freebsd-dev/sys/dev/mmc/bridge.h

/*-
 * Copyright (c) 2006 M. Warner Losh.  All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 *
 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
 * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
 * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
 * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
 * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 *
 * $FreeBSD$
 */

#ifndef DEV_MMC_BRIDGE_H
#define DEV_MMC_BRIDGE_H

/*
 * This file defines interfaces for the mmc bridge.  The names chosen
 * are similar to or the same as the names used in Linux to allow for
 * easy porting of what Linux calls mmc host drivers.  I use the
 * FreeBSD terminology of bridge and bus for consistancy with other
 * drivers in the system.  This file corresponds roughly to the Linux
 * linux/mmc/host.h file.
 *
 * A mmc bridge is a chipset that can have one or more mmc and/or sd
 * cards attached to it.  mmc cards are attached on a bus topology,
 * while sd and sdio cards are attached using a star topology (meaning
 * in practice each sd card has its own, independent slot).  Each
 * mmcbr is assumed to be derived from the mmcbr.  This is done to
 * allow for easier addition of bridges (as each bridge does not need
 * to be added to the mmcbus file).
 *
 * Attached to the mmc bridge is an mmcbus.  The mmcbus is described
 * in dev/mmc/bus.h.
 */


/*
 * mmc_ios is a structure that is used to store the state of the mmc/sd
 * bus configuration.  This include the bus' clock speed, its voltage,
 * the bus mode for command output, the SPI chip select, some power
 * states and the bus width.
 */
enum mmc_vdd {
	vdd_150 = 0, vdd_155, vdd_160, vdd_165, vdd_170, vdd_180,
	vdd_190, vdd_200, vdd_210, vdd_220, vdd_230, vdd_240, vdd_250,
	vdd_260, vdd_270, vdd_280, vdd_290, vdd_300, vdd_310, vdd_320,
	vdd_330, vdd_340, vdd_350, vdd_360
};

enum mmc_power_mode {
	power_off = 0, power_up, power_on
};

enum mmc_bus_mode {
	opendrain = 1, pushpull
};

enum mmc_chip_select {
	cs_dontcare = 0, cs_high, cs_low
};

enum mmc_bus_width {
	bus_width_1 = 0, bus_width_4 = 2, bus_width_8 = 3
};

struct mmc_ios {
	uint32_t	clock;	/* Speed of the clock in Hz to move data */
	enum mmc_vdd	vdd;	/* Voltage to apply to the power pins/ */
	enum mmc_bus_mode bus_mode;
	enum mmc_chip_select chip_select;
	enum mmc_bus_width bus_width;
	enum mmc_power_mode power_mode;
};

enum mmc_card_mode {
	mode_mmc, mode_sd
};

struct mmc_host {
	int f_min;
	int f_max;
	uint32_t host_ocr;
	uint32_t ocr;
	uint32_t caps;
#define MMC_CAP_4_BIT_DATA	(1 << 0) /* Can do 4-bit data transfers */
#define MMC_CAP_8_BIT_DATA	(1 << 1) /* Can do 8-bit data transfers */
	enum mmc_card_mode mode;
	struct mmc_ios ios;	/* Current state of the host */
};

#endif /* DEV_MMC_BRIDGE_H */