freebsd-dev/sys/cam/cam_xpt_sim.h

60 lines
2.4 KiB
C
Raw Normal View History

/*-
* Data structures and definitions for dealing with the
* Common Access Method Transport (xpt) layer.
*
* Copyright (c) 1997 Justin T. Gibbs.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions, and the following disclaimer,
* without modification, immediately at the beginning of the file.
* 2. The name of the author may not be used to endorse or promote products
* derived from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
1999-08-28 01:08:13 +00:00
* $FreeBSD$
*/
#ifndef _CAM_CAM_XPT_SIM_H
#define _CAM_CAM_XPT_SIM_H 1
#include <cam/cam_xpt.h>
#include <cam/cam_queue.h>
/* Functions accessed by SIM drivers */
#ifdef _KERNEL
int32_t xpt_bus_register(struct cam_sim *sim, device_t parent,
u_int32_t bus);
int32_t xpt_bus_deregister(path_id_t path_id);
u_int32_t xpt_freeze_simq(struct cam_sim *sim, u_int count);
void xpt_release_simq(struct cam_sim *sim, int run_queue);
u_int32_t xpt_freeze_devq(struct cam_path *path, u_int count);
MFp4: Large set of CAM inprovements. - Unify bus reset/probe sequence. Whenever bus attached at boot or later, CAM will automatically reset and scan it. It allows to remove duplicate code from many drivers. - Any bus, attached before CAM completed it's boot-time initialization, will equally join to the process, delaying boot if needed. - New kern.cam.boot_delay loader tunable should help controllers that are still unable to register their buses in time (such as slow USB/ PCCard/ CardBus devices), by adding one more event to wait on boot. - To allow synchronization between different CAM levels, concept of requests priorities was extended. Priorities now split between several "run levels". Device can be freezed at specified level, allowing higher priority requests to pass. For example, no payload requests allowed, until PMP driver enable port. ATA XPT negotiate transfer parameters, periph driver configure caching and so on. - Frozen requests are no more counted by request allocation scheduler. It fixes deadlocks, when frozen low priority payload requests occupying slots, required by higher levels to manage theit execution. - Two last changes were holding proper ATA reinitialization and error recovery implementation. Now it is done: SATA controllers and Port Multipliers now implement automatic hot-plug and should correctly recover from timeouts and bus resets. - Improve SCSI error recovery for devices on buses without automatic sense reporting, such as ATAPI or USB. For example, it allows CAM to wait, while CD drive loads disk, instead of immediately return error status. - Decapitalize diagnostic messages and make them more readable and sensible. - Teach PMP driver to limit maximum speed on fan-out ports. - Make boot wait for PMP scan completes, and make rescan more reliable. - Fix pass driver, to return CCB to user level in case of error. - Increase number of retries in cd driver, as device may return several UAs.
2010-01-28 08:41:30 +00:00
u_int32_t xpt_freeze_devq_rl(struct cam_path *path, cam_rl rl,
u_int count);
void xpt_release_devq(struct cam_path *path,
u_int count, int run_queue);
void xpt_release_devq_rl(struct cam_path *path, cam_rl rl,
u_int count, int run_queue);
int xpt_sim_opened(struct cam_sim *sim);
void xpt_done(union ccb *done_ccb);
void xpt_batch_start(struct cam_sim *sim);
void xpt_batch_done(struct cam_sim *sim);
#endif
#endif /* _CAM_CAM_XPT_SIM_H */