freebsd-dev/sys/dev/ep/if_epvar.h

113 lines
3.9 KiB
C
Raw Normal View History

/*-
* Copyright (c) 1993 Herb Peyerl (hpeyerl@novatel.ca) All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are
* met: 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer. 2. The name
* of the author may not be used to endorse or promote products derived from
* this software without specific prior written permission
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR IMPLIED
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
* EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
* SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED
* TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
* PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
* LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
* NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
* $FreeBSD$
*/
HEADS UP! All 3c5x9 users! - Rip out all the static softc stuff and do softc allocation the right way. - Rewrite most of the ISA code so that it provides a DEVICE_IDENTIFY method to enumerate all non-PnP ISA devices. This has the following consequences: - No 'ep' devices may be hardwired. - All hardwired devices will probably be detected twice. By hardwired I mean: device ep0 at isa? port 0x300 irq 10 - 'ep' devices are ordered by bus, slot, and then MAC address. - Make 3c509B cards work in PnP mode. Yes, they really work. - Convert over to using ifmedia for media selection. No more of this lame 'linkX' stuff. - Consolidate a lot of duplicated code. - Make a stab at not breaking MII based PCCARD devices. I doubt that the PCCARD stuff works any more than it did before my changes but theres hope. My PCCARD hardware should arrive in a week or so. - Retreive the media settings from the card EEPROM rather than guessing. I've got a 3c509-TPO that thinks its got an AUI port and if others can report similar problems I'll write a bit of clever code that will fix this but right now it works correctly on all but 1 card. - Clean up a few things and make some cosmetic changes. - Add myself as the MAINTAINER since nobody else wants to. I'm in the best position to do this as I've got an example of most of the cards: EISA 3c579 bnc/aui MCA 3c529 tp/aui ISA 3c509 tpo ISA-PnP 3c509B combo If someone wants to send me a any cards I don't have I'd appriciate it. Also welcome are 3c59x boards since I'll be folding if_vx and if_ep at some point.
1999-10-27 06:25:16 +00:00
struct ep_board {
u_short prod_id; /* product ID */
int cmd_off; /* command offset (bit shift) */
int mii_trans; /* activate MII transiever */
u_short res_cfg; /* resource configuration */
HEADS UP! All 3c5x9 users! - Rip out all the static softc stuff and do softc allocation the right way. - Rewrite most of the ISA code so that it provides a DEVICE_IDENTIFY method to enumerate all non-PnP ISA devices. This has the following consequences: - No 'ep' devices may be hardwired. - All hardwired devices will probably be detected twice. By hardwired I mean: device ep0 at isa? port 0x300 irq 10 - 'ep' devices are ordered by bus, slot, and then MAC address. - Make 3c509B cards work in PnP mode. Yes, they really work. - Convert over to using ifmedia for media selection. No more of this lame 'linkX' stuff. - Consolidate a lot of duplicated code. - Make a stab at not breaking MII based PCCARD devices. I doubt that the PCCARD stuff works any more than it did before my changes but theres hope. My PCCARD hardware should arrive in a week or so. - Retreive the media settings from the card EEPROM rather than guessing. I've got a 3c509-TPO that thinks its got an AUI port and if others can report similar problems I'll write a bit of clever code that will fix this but right now it works correctly on all but 1 card. - Clean up a few things and make some cosmetic changes. - Add myself as the MAINTAINER since nobody else wants to. I'm in the best position to do this as I've got an example of most of the cards: EISA 3c579 bnc/aui MCA 3c529 tp/aui ISA 3c509 tpo ISA-PnP 3c509B combo If someone wants to send me a any cards I don't have I'd appriciate it. Also welcome are 3c59x boards since I'll be folding if_vx and if_ep at some point.
1999-10-27 06:25:16 +00:00
};
/*
* Ethernet software status per interface.
*/
struct ep_softc {
struct ifnet *ifp;
struct ifmedia ifmedia; /* media info */
device_t dev;
HEADS UP! All 3c5x9 users! - Rip out all the static softc stuff and do softc allocation the right way. - Rewrite most of the ISA code so that it provides a DEVICE_IDENTIFY method to enumerate all non-PnP ISA devices. This has the following consequences: - No 'ep' devices may be hardwired. - All hardwired devices will probably be detected twice. By hardwired I mean: device ep0 at isa? port 0x300 irq 10 - 'ep' devices are ordered by bus, slot, and then MAC address. - Make 3c509B cards work in PnP mode. Yes, they really work. - Convert over to using ifmedia for media selection. No more of this lame 'linkX' stuff. - Consolidate a lot of duplicated code. - Make a stab at not breaking MII based PCCARD devices. I doubt that the PCCARD stuff works any more than it did before my changes but theres hope. My PCCARD hardware should arrive in a week or so. - Retreive the media settings from the card EEPROM rather than guessing. I've got a 3c509-TPO that thinks its got an AUI port and if others can report similar problems I'll write a bit of clever code that will fix this but right now it works correctly on all but 1 card. - Clean up a few things and make some cosmetic changes. - Add myself as the MAINTAINER since nobody else wants to. I'm in the best position to do this as I've got an example of most of the cards: EISA 3c579 bnc/aui MCA 3c529 tp/aui ISA 3c509 tpo ISA-PnP 3c509B combo If someone wants to send me a any cards I don't have I'd appriciate it. Also welcome are 3c59x boards since I'll be folding if_vx and if_ep at some point.
1999-10-27 06:25:16 +00:00
struct mtx sc_mtx;
struct resource *iobase;
struct resource *irq;
HEADS UP! All 3c5x9 users! - Rip out all the static softc stuff and do softc allocation the right way. - Rewrite most of the ISA code so that it provides a DEVICE_IDENTIFY method to enumerate all non-PnP ISA devices. This has the following consequences: - No 'ep' devices may be hardwired. - All hardwired devices will probably be detected twice. By hardwired I mean: device ep0 at isa? port 0x300 irq 10 - 'ep' devices are ordered by bus, slot, and then MAC address. - Make 3c509B cards work in PnP mode. Yes, they really work. - Convert over to using ifmedia for media selection. No more of this lame 'linkX' stuff. - Consolidate a lot of duplicated code. - Make a stab at not breaking MII based PCCARD devices. I doubt that the PCCARD stuff works any more than it did before my changes but theres hope. My PCCARD hardware should arrive in a week or so. - Retreive the media settings from the card EEPROM rather than guessing. I've got a 3c509-TPO that thinks its got an AUI port and if others can report similar problems I'll write a bit of clever code that will fix this but right now it works correctly on all but 1 card. - Clean up a few things and make some cosmetic changes. - Add myself as the MAINTAINER since nobody else wants to. I'm in the best position to do this as I've got an example of most of the cards: EISA 3c579 bnc/aui MCA 3c529 tp/aui ISA 3c509 tpo ISA-PnP 3c509B combo If someone wants to send me a any cards I don't have I'd appriciate it. Also welcome are 3c59x boards since I'll be folding if_vx and if_ep at some point.
1999-10-27 06:25:16 +00:00
2003-10-19 00:03:10 +00:00
bus_space_handle_t bsh;
bus_space_tag_t bst;
void *ep_intrhand;
HEADS UP! All 3c5x9 users! - Rip out all the static softc stuff and do softc allocation the right way. - Rewrite most of the ISA code so that it provides a DEVICE_IDENTIFY method to enumerate all non-PnP ISA devices. This has the following consequences: - No 'ep' devices may be hardwired. - All hardwired devices will probably be detected twice. By hardwired I mean: device ep0 at isa? port 0x300 irq 10 - 'ep' devices are ordered by bus, slot, and then MAC address. - Make 3c509B cards work in PnP mode. Yes, they really work. - Convert over to using ifmedia for media selection. No more of this lame 'linkX' stuff. - Consolidate a lot of duplicated code. - Make a stab at not breaking MII based PCCARD devices. I doubt that the PCCARD stuff works any more than it did before my changes but theres hope. My PCCARD hardware should arrive in a week or so. - Retreive the media settings from the card EEPROM rather than guessing. I've got a 3c509-TPO that thinks its got an AUI port and if others can report similar problems I'll write a bit of clever code that will fix this but right now it works correctly on all but 1 card. - Clean up a few things and make some cosmetic changes. - Add myself as the MAINTAINER since nobody else wants to. I'm in the best position to do this as I've got an example of most of the cards: EISA 3c579 bnc/aui MCA 3c529 tp/aui ISA 3c509 tpo ISA-PnP 3c509B combo If someone wants to send me a any cards I don't have I'd appriciate it. Also welcome are 3c59x boards since I'll be folding if_vx and if_ep at some point.
1999-10-27 06:25:16 +00:00
struct callout watchdog_timer;
int tx_timer;
u_short ep_connectors; /* Connectors on this card. */
u_char ep_connector; /* Configured connector. */
struct mbuf *top;
struct mbuf *mcur;
short cur_len;
HEADS UP! All 3c5x9 users! - Rip out all the static softc stuff and do softc allocation the right way. - Rewrite most of the ISA code so that it provides a DEVICE_IDENTIFY method to enumerate all non-PnP ISA devices. This has the following consequences: - No 'ep' devices may be hardwired. - All hardwired devices will probably be detected twice. By hardwired I mean: device ep0 at isa? port 0x300 irq 10 - 'ep' devices are ordered by bus, slot, and then MAC address. - Make 3c509B cards work in PnP mode. Yes, they really work. - Convert over to using ifmedia for media selection. No more of this lame 'linkX' stuff. - Consolidate a lot of duplicated code. - Make a stab at not breaking MII based PCCARD devices. I doubt that the PCCARD stuff works any more than it did before my changes but theres hope. My PCCARD hardware should arrive in a week or so. - Retreive the media settings from the card EEPROM rather than guessing. I've got a 3c509-TPO that thinks its got an AUI port and if others can report similar problems I'll write a bit of clever code that will fix this but right now it works correctly on all but 1 card. - Clean up a few things and make some cosmetic changes. - Add myself as the MAINTAINER since nobody else wants to. I'm in the best position to do this as I've got an example of most of the cards: EISA 3c579 bnc/aui MCA 3c529 tp/aui ISA 3c509 tpo ISA-PnP 3c509B combo If someone wants to send me a any cards I don't have I'd appriciate it. Also welcome are 3c59x boards since I'll be folding if_vx and if_ep at some point.
1999-10-27 06:25:16 +00:00
int stat; /* some flags */
HEADS UP! All 3c5x9 users! - Rip out all the static softc stuff and do softc allocation the right way. - Rewrite most of the ISA code so that it provides a DEVICE_IDENTIFY method to enumerate all non-PnP ISA devices. This has the following consequences: - No 'ep' devices may be hardwired. - All hardwired devices will probably be detected twice. By hardwired I mean: device ep0 at isa? port 0x300 irq 10 - 'ep' devices are ordered by bus, slot, and then MAC address. - Make 3c509B cards work in PnP mode. Yes, they really work. - Convert over to using ifmedia for media selection. No more of this lame 'linkX' stuff. - Consolidate a lot of duplicated code. - Make a stab at not breaking MII based PCCARD devices. I doubt that the PCCARD stuff works any more than it did before my changes but theres hope. My PCCARD hardware should arrive in a week or so. - Retreive the media settings from the card EEPROM rather than guessing. I've got a 3c509-TPO that thinks its got an AUI port and if others can report similar problems I'll write a bit of clever code that will fix this but right now it works correctly on all but 1 card. - Clean up a few things and make some cosmetic changes. - Add myself as the MAINTAINER since nobody else wants to. I'm in the best position to do this as I've got an example of most of the cards: EISA 3c579 bnc/aui MCA 3c529 tp/aui ISA 3c509 tpo ISA-PnP 3c509B combo If someone wants to send me a any cards I don't have I'd appriciate it. Also welcome are 3c59x boards since I'll be folding if_vx and if_ep at some point.
1999-10-27 06:25:16 +00:00
#define F_RX_FIRST 0x001
2005-07-01 04:23:32 +00:00
#define F_ENADDR_SKIP 0x002
HEADS UP! All 3c5x9 users! - Rip out all the static softc stuff and do softc allocation the right way. - Rewrite most of the ISA code so that it provides a DEVICE_IDENTIFY method to enumerate all non-PnP ISA devices. This has the following consequences: - No 'ep' devices may be hardwired. - All hardwired devices will probably be detected twice. By hardwired I mean: device ep0 at isa? port 0x300 irq 10 - 'ep' devices are ordered by bus, slot, and then MAC address. - Make 3c509B cards work in PnP mode. Yes, they really work. - Convert over to using ifmedia for media selection. No more of this lame 'linkX' stuff. - Consolidate a lot of duplicated code. - Make a stab at not breaking MII based PCCARD devices. I doubt that the PCCARD stuff works any more than it did before my changes but theres hope. My PCCARD hardware should arrive in a week or so. - Retreive the media settings from the card EEPROM rather than guessing. I've got a 3c509-TPO that thinks its got an AUI port and if others can report similar problems I'll write a bit of clever code that will fix this but right now it works correctly on all but 1 card. - Clean up a few things and make some cosmetic changes. - Add myself as the MAINTAINER since nobody else wants to. I'm in the best position to do this as I've got an example of most of the cards: EISA 3c579 bnc/aui MCA 3c529 tp/aui ISA 3c509 tpo ISA-PnP 3c509B combo If someone wants to send me a any cards I don't have I'd appriciate it. Also welcome are 3c59x boards since I'll be folding if_vx and if_ep at some point.
1999-10-27 06:25:16 +00:00
#define F_PROMISC 0x008
#define F_ACCESS_32_BITS 0x100
#define F_HAS_TX_PLL 0x200
int gone; /* adapter is not present (for PCCARD) */
struct ep_board epb;
2005-07-01 04:23:32 +00:00
uint8_t eaddr[6];
#ifdef EP_LOCAL_STATS
short tx_underrun;
short rx_no_first;
short rx_no_mbuf;
short rx_overrunf;
short rx_overrunl;
#endif
};
int ep_alloc(device_t);
void ep_free(device_t);
int ep_detach(device_t);
void ep_get_media(struct ep_softc *);
int ep_attach(struct ep_softc *);
void ep_intr(void *);
int ep_get_e(struct ep_softc *, uint16_t, uint16_t *);
#define CSR_READ_1(sc, off) (bus_space_read_1((sc)->bst, (sc)->bsh, off))
#define CSR_READ_2(sc, off) (bus_space_read_2((sc)->bst, (sc)->bsh, off))
#define CSR_WRITE_1(sc, off, val) \
bus_space_write_1(sc->bst, sc->bsh, off, val)
#define CSR_WRITE_2(sc, off, val) \
bus_space_write_2(sc->bst, sc->bsh, off, val)
#define CSR_WRITE_MULTI_1(sc, off, addr, count) \
bus_space_write_multi_1(sc->bst, sc->bsh, off, addr, count)
#define CSR_WRITE_MULTI_2(sc, off, addr, count) \
bus_space_write_multi_2(sc->bst, sc->bsh, off, addr, count)
#define CSR_WRITE_MULTI_4(sc, off, addr, count) \
bus_space_write_multi_4(sc->bst, sc->bsh, off, addr, count)
#define CSR_READ_MULTI_1(sc, off, addr, count) \
bus_space_read_multi_1(sc->bst, sc->bsh, off, addr, count)
#define CSR_READ_MULTI_2(sc, off, addr, count) \
bus_space_read_multi_2(sc->bst, sc->bsh, off, addr, count)
#define CSR_READ_MULTI_4(sc, off, addr, count) \
bus_space_read_multi_4(sc->bst, sc->bsh, off, addr, count)
#define EP_LOCK(_sc) mtx_lock(&(_sc)->sc_mtx)
#define EP_UNLOCK(_sc) mtx_unlock(&(_sc)->sc_mtx)
#define EP_LOCK_INIT(_sc) \
mtx_init(&_sc->sc_mtx, device_get_nameunit(_sc->dev), \
MTX_NETWORK_LOCK, MTX_DEF)
#define EP_LOCK_DESTROY(_sc) mtx_destroy(&_sc->sc_mtx);
#define EP_ASSERT_LOCKED(_sc) mtx_assert(&_sc->sc_mtx, MA_OWNED);
#define EP_ASSERT_UNLOCKED(_sc) mtx_assert(&_sc->sc_mtx, MA_NOTOWNED);