freebsd-dev/sys/modules/aac/Makefile

# $FreeBSD$

.PATH: ${SRCTOP}/sys/dev/aac

.if ${MACHINE_CPUARCH} == "i386"
SUBDIR= aac_linux
.endif

KMOD=	aac
SRCS=	aac.c aac_pci.c aac_disk.c aac_cam.c
SRCS+=	opt_scsi.h opt_cam.h opt_aac.h
SRCS+=	device_if.h bus_if.h pci_if.h

# To enable debug output from the driver, uncomment these two lines.
#CFLAGS+= -DAAC_DEBUG=2
#SRCS+=	aac_debug.c

.include <bsd.kmod.mk>
A new driver for PCI:SCSI RAID controllers based on the Adaptec FSA design. This includes integrated Dell RAID controllers, the Dell PERC 2/QC and the HP NetRAID-4M. 2000-09-13 03:20:35 +00:00			`# $FreeBSD$`

sys/modules: normalize .CURDIR-relative paths to SRCTOP This simplifies make output/logic Tested with: `cd sys/modules; make ALL_MODULES=` on amd64 MFC after: 1 month Sponsored by: Dell EMC Isilon 2017-03-04 10:10:17 +00:00			`.PATH: ${SRCTOP}/sys/dev/aac`
A new driver for PCI:SCSI RAID controllers based on the Adaptec FSA design. This includes integrated Dell RAID controllers, the Dell PERC 2/QC and the HP NetRAID-4M. 2000-09-13 03:20:35 +00:00
MFtbemd: Use MACHINE_CPUARCH in preference to MACHINE_ARCH. The former is the source code location of the machine, the latter the binary output. In general, we want to use MACHINE_CPUARCH instead of MACHINE_ARCH unless we're tesitng for a specific target. The isn't even moot for i386/amd64 where there's momemntum towards a MACHINE_CPUARCH == x86, although a specific cleanup for that likely would be needed... 2010-08-23 06:13:29 +00:00			`.if ${MACHINE_CPUARCH} == "i386"`
The AAC_COMPAT_LINUX option was really annoying, since it made the aac driver dependent on the linux emulation module. This was especially bad for the release engineers who tried to move the aac driver from the kernel onto the drivers floppy. The linux compat bits for this driver are now in their own driver, aac_linux. It can be loaded as a module or compiled into the kernel. For the latter case, the AAC_COMPAT_LINUX option is needed, along with the COMPAT_LINUX option. I've tested this in every configuration I can think of. This is an MFC candidate for 4.7. Idea from: rwatson MFC after: 3 days 2002-09-25 05:00:25 +00:00			`SUBDIR= aac_linux`
Only compile aac_linux.ko for i386 2004-08-30 03:35:17 +00:00			`.endif`
The AAC_COMPAT_LINUX option was really annoying, since it made the aac driver dependent on the linux emulation module. This was especially bad for the release engineers who tried to move the aac driver from the kernel onto the drivers floppy. The linux compat bits for this driver are now in their own driver, aac_linux. It can be loaded as a module or compiled into the kernel. For the latter case, the AAC_COMPAT_LINUX option is needed, along with the COMPAT_LINUX option. I've tested this in every configuration I can think of. This is an MFC candidate for 4.7. Idea from: rwatson MFC after: 3 days 2002-09-25 05:00:25 +00:00
Use a consistent style and one much closer to the rest of /usr/src 2001-01-06 14:00:42 +00:00			`KMOD= aac`
Add a CAM interface to the aac driver. This is useful in case you should ever connect a SCSI Cdrom/Tape/Jukebox/Scanner/Printer/kitty-litter-scooper to your high-end RAID controller. The interface to the arrays is still via the block interface; this merely provides a way to circumvent the RAID functionality and access the SCSI buses directly. Note that for somewhat obvious reasons, hard drives are not exposed to the da driver through this interface, though you can still talk to them via the pass driver. Be the first on your block to low-level format unsuspecting drives that are part of an array! To enable this, add the 'aacp' device to your kernel config. MFC after: 3 days 2002-04-27 01:31:17 +00:00			`SRCS= aac.c aac_pci.c aac_disk.c aac_cam.c`
Move most of the contents of opt_compat.h to opt_global.h. opt_compat.h is mentioned in nearly 180 files. In-progress network driver compabibility improvements may add over 100 more so this is closer to "just about everywhere" than "only some files" per the guidance in sys/conf/options. Keep COMPAT_LINUX32 in opt_compat.h as it is confined to a subset of sys/compat/linux/*.c. A fake _COMPAT_LINUX option ensure opt_compat.h is created on all architectures. Move COMPAT_LINUXKPI to opt_dontuse.h as it is only used to control the set of compiled files. Reviewed by: kib, cem, jhb, jtl Sponsored by: DARPA, AFRL Differential Revision: https://reviews.freebsd.org/D14941 2018-04-06 17:35:35 +00:00			`SRCS+= opt_scsi.h opt_cam.h opt_aac.h`
Use a consistent style and one much closer to the rest of /usr/src 2001-01-06 14:00:42 +00:00			`SRCS+= device_if.h bus_if.h pci_if.h`
A new driver for PCI:SCSI RAID controllers based on the Adaptec FSA design. This includes integrated Dell RAID controllers, the Dell PERC 2/QC and the HP NetRAID-4M. 2000-09-13 03:20:35 +00:00
Fix the building of the aac driver as a module. Add a comment about enabling debug information for the driver. 2001-03-17 04:42:33 +00:00			`# To enable debug output from the driver, uncomment these two lines.`
Use a consistent style and one much closer to the rest of /usr/src 2001-01-06 14:00:42 +00:00			`#CFLAGS+= -DAAC_DEBUG=2`
			`#SRCS+= aac_debug.c`
A new driver for PCI:SCSI RAID controllers based on the Adaptec FSA design. This includes integrated Dell RAID controllers, the Dell PERC 2/QC and the HP NetRAID-4M. 2000-09-13 03:20:35 +00:00
			`.include <bsd.kmod.mk>`