d/freebsd-dev
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
9cf43b9716
freebsd-dev/sys/dev/isp/isp.c

4948 lines
129 KiB
C
Raw Normal View History

$Id$ -> $FreeBSD$
1999-08-28 01:08:13 +00:00
/* $FreeBSD$ */
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
/*
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
* Machine and OS Independent (well, as best as possible)
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
* code for the Qlogic ISP SCSI adapters.
*
some copyright cleanups
2000-09-21 20:16:04 +00:00
* Copyright (c) 1997, 1998, 1999, 2000 by Matthew Jacob
* Feral Software
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice immediately at the beginning of the file, without modification,
* this list of conditions, and the following disclaimer.
some copyright cleanups
2000-09-21 20:16:04 +00:00
* 2. The name of the author may not be used to endorse or promote products
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
* derived from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*/
/*
* Inspiration and ideas about this driver are from Erik Moe's Linux driver
* (qlogicisp.c) and Dave Miller's SBus version of same (qlogicisp.c). Some
* ideas dredged from the Solaris driver.
*/
/*
* Include header file appropriate for platform we're building on.
*/
#ifdef __NetBSD__
#include <dev/ic/isp_netbsd.h>
#endif
#ifdef __FreeBSD__
#include <dev/isp/isp_freebsd.h>
#endif
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
#ifdef __OpenBSD__
#include <dev/ic/isp_openbsd.h>
#endif
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
#ifdef __linux__
clarify headers;move uninit to outer layer;remove watchdog
1998-12-28 19:22:27 +00:00
#include "isp_linux.h"
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
#endif
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
#ifdef __svr4__
#include "isp_solaris.h"
#endif
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
/*
* General defines
*/
#define MBOX_DELAY_COUNT 1000000 / 100
/*
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
* Local static data
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
*/
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
static char *warnlun =
"WARNING- cannot determine Expanded LUN capability- limiting to one LUN";
static char *portshift =
"Target %d Loop ID 0x%x (Port 0x%x) => Loop 0x%x (Port 0x%x)";
static char *portdup =
"Target %d duplicates Target %d- killing off both";
static char *retained =
"Retaining Loop ID 0x%x for Target %d (Port 0x%x)";
#ifdef ISP2100_FABRIC
static char *lretained =
"Retained login of Target %d (Loop ID 0x%x) Port 0x%x";
static char *plogout =
"Logging out Target %d at Loop ID 0x%x (Port 0x%x)";
static char *plogierr =
"Command Error in PLOGI for Port 0x%x (0x%x)";
static char *nopdb =
"Could not get PDB for Device @ Port 0x%x";
static char *pdbmfail1 =
"PDB Loop ID info for Device @ Port 0x%x does not match up (0x%x)";
static char *pdbmfail2 =
"PDB Port info for Device @ Port 0x%x does not match up (0x%x)";
static char *ldumped =
"Target %d (Loop ID 0x%x) Port 0x%x dumped after login info mismatch";
#endif
static char *notresp =
"Not RESPONSE in RESPONSE Queue (type 0x%x) @ idx %d (next %d)";
static char *xact1 =
"HBA attempted queued transaction with disconnect not set for %d.%d.%d";
static char *xact2 =
"HBA attempted queued transaction to target routine %d on target %d bus %d";
static char *xact3 =
"HBA attempted queued cmd for %d.%d.%d when queueing disabled";
static char *pskip =
"SCSI phase skipped for target %d.%d.%d";
static char *topology =
"Loop ID %d, AL_PA 0x%x, Port ID 0x%x, Loop State 0x%x, Topology '%s'";
static char *finmsg =
"(%d.%d.%d): FIN dl%d resid%d STS 0x%x SKEY %c XS_ERR=0x%x";
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
/*
* Local function prototypes.
*/
Remove the Target mode functions until they're in better shape. Implement some suggested compilation cleanups from Eklund. Wire down a hard loop id if we are not on a platform that has the ability to get to a PCI BIOS (it still will float to the ID it gets after a LIP but at least we can try). Clarify that the expanded lun is based upon SCCLUN defines (in f/w).
1998-12-05 01:33:57 +00:00
static int isp_parse_async __P((struct ispsoftc *, int));
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
static int isp_handle_other_response
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
__P((struct ispsoftc *, ispstatusreq_t *, u_int16_t *));
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
static void isp_parse_status
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
__P((struct ispsoftc *, ispstatusreq_t *, XS_T *));
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
static void isp_fastpost_complete __P((struct ispsoftc *, u_int32_t));
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
static void isp_scsi_init __P((struct ispsoftc *));
static void isp_scsi_channel_init __P((struct ispsoftc *, int));
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
static void isp_fibre_init __P((struct ispsoftc *));
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
static void isp_mark_getpdb_all __P((struct ispsoftc *));
static int isp_getpdb __P((struct ispsoftc *, int, isp_pdb_t *));
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
static u_int64_t isp_get_portname __P((struct ispsoftc *, int, int));
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
static int isp_fclink_test __P((struct ispsoftc *, int));
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
static char *isp2100_fw_statename __P((int));
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
static int isp_same_lportdb __P((struct lportdb *, struct lportdb *));
static int isp_pdb_sync __P((struct ispsoftc *, int));
#ifdef ISP2100_FABRIC
static int isp_scan_fabric __P((struct ispsoftc *));
#endif
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
static void isp_fw_state __P((struct ispsoftc *));
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
static void isp_mboxcmd __P((struct ispsoftc *, mbreg_t *, int));
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
static void isp_update __P((struct ispsoftc *));
static void isp_update_bus __P((struct ispsoftc *, int));
static void isp_setdfltparm __P((struct ispsoftc *, int));
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
static int isp_read_nvram __P((struct ispsoftc *));
static void isp_rdnvram_word __P((struct ispsoftc *, int, u_int16_t *));
Restructure nvram reading routine to split out to separate functions for 1020/1X80/12160/2X00- for readability. Add in 12160 (Ultra3) support- but not with PPR just yet. Fix and clarify fetching of return parameter for getting firmware rev which for the 2200 contains the connection topology (Private Loop (NL-port), N-port, FL-port, F-port). Synthesize the connection topology for the 2100 which can only be Private Loop or FL-port. Handle a couple of new async mailbox commands which signify connection in Point-to-Point mode (N-port or F-port) or indicate various toe stubbing getting to same. Approved: jkh@freebsd.org
2000-02-11 19:31:32 +00:00
static void isp_parse_nvram_1020 __P((struct ispsoftc *, u_int8_t *));
static void isp_parse_nvram_1080 __P((struct ispsoftc *, int, u_int8_t *));
static void isp_parse_nvram_12160 __P((struct ispsoftc *, int, u_int8_t *));
static void isp_parse_nvram_2100 __P((struct ispsoftc *, u_int8_t *));
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
/*
* Reset Hardware.
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
*
Use pointer to f/w in md structure as to whether f/w exists or not. If firmware length isn't specified, extract from the 4th short into the firmware.
1999-10-30 19:32:44 +00:00
* Hit the chip over the head, download new f/w if available and set it running.
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
*
* Locking done elsewhere.
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
*/
void
isp_reset(isp)
struct ispsoftc *isp;
{
mbreg_t mbs;
Once we have firmware running (if isp_reset) and this is the first time through, establish what our LUN width is. Unfortunately, we can't ask the f/w. If we loaded the f/w, we'll now assume we have expanded LUNs (SCCLUN for fibre channel, just plain 32 LUN for SCSI). If we didn't load firmware, assume 8 LUNs for SCSI and 1 LUN for Fibre Channel. We have to assume only one LUN for Fibre Channel because the LUN setting in Request Queue entries is in different places whether we have SCCLUN firmware or not, so the only LUN guaranteed to work for both is LUN 0. Clean up the rest of isp.c so that ISP2100_SCCLUN defines aren't used- instead use run time determinants based upon isp->isp_maxluns. After starting firmware, delay 500us to give it a chance to get rolling. Fix the interrupt service routine to check for both isr && sema being zero before thinking this was a spurious interrupt. Following the manuals, allow for both Mailbox as well as Queue Reponse type interrupts for regular SCSI.
2000-06-18 04:56:17 +00:00
int loops, i, touched, dodnld = 1;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
char *revname;
isp->isp_state = ISP_NILSTATE;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
/*
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
* Basic types (SCSI, FibreChannel and PCI or SBus)
* have been set in the MD code. We figure out more
* here.
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
*
Roll internal release tag. Print out if we're in a 64 bit PCI slot. Use fast memory timing NVRAM parameter. Clean up and fix establishment of default target parameters. Don't use NVRAM if are flagged as not to do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC mode but disabled disconnect/reconnect and wide!!). Fix delays after resets. BUS resets not done in isp_init anymore- relegated to OS specific outer layers. Fix a buglet where you can get in a loop for a NULL xs in the completion list in isp_intr. Add in some defines that can disable fast posting. Add in code for Loop Up/Loop Down events that call into the outer layers as to what to do.
1999-02-09 01:07:06 +00:00
* After we've fired this chip up, zero out the conf1 register
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
* for SCSI adapters and do other settings for the 2100.
Roll internal release tag. Print out if we're in a 64 bit PCI slot. Use fast memory timing NVRAM parameter. Clean up and fix establishment of default target parameters. Don't use NVRAM if are flagged as not to do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC mode but disabled disconnect/reconnect and wide!!). Fix delays after resets. BUS resets not done in isp_init anymore- relegated to OS specific outer layers. Fix a buglet where you can get in a loop for a NULL xs in the completion list in isp_intr. Add in some defines that can disable fast posting. Add in code for Loop Up/Loop Down events that call into the outer layers as to what to do.
1999-02-09 01:07:06 +00:00
*/
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
/*
* Get the current running firmware revision out of the
* chip before we hit it over the head (if this is our
* first time through). Note that we store this as the
* 'ROM' firmware revision- which it may not be. In any
* case, we don't really use this yet, but we may in
* the future.
*/
Once we have firmware running (if isp_reset) and this is the first time through, establish what our LUN width is. Unfortunately, we can't ask the f/w. If we loaded the f/w, we'll now assume we have expanded LUNs (SCCLUN for fibre channel, just plain 32 LUN for SCSI). If we didn't load firmware, assume 8 LUNs for SCSI and 1 LUN for Fibre Channel. We have to assume only one LUN for Fibre Channel because the LUN setting in Request Queue entries is in different places whether we have SCCLUN firmware or not, so the only LUN guaranteed to work for both is LUN 0. Clean up the rest of isp.c so that ISP2100_SCCLUN defines aren't used- instead use run time determinants based upon isp->isp_maxluns. After starting firmware, delay 500us to give it a chance to get rolling. Fix the interrupt service routine to check for both isr && sema being zero before thinking this was a spurious interrupt. Following the manuals, allow for both Mailbox as well as Queue Reponse type interrupts for regular SCSI.
2000-06-18 04:56:17 +00:00
if ((touched = isp->isp_touched) == 0) {
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
/*
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
* First see whether or not we're sitting in the ISP PROM.
* If we've just been reset, we'll have the string "ISP "
* spread through outgoing mailbox registers 1-3.
Make firmware revision a triple. Clean up some FC init stuff for board versions with no BIOS. Separate mailbox interrupts from IOCB interrupts. Read OUTMAILBOX5 while RISC_INT is active- not after you clear it (potential race condition). Clear out older broken BIG_ENDIAN goop. Don't negotiate narrow/async for LVD busses at startup if already in LVD mode. Note usage of presumptive 1040C revision. For all the LIP, PDB Changed, Loop UP/DOWN async events, mark fw state as unknown as well as marking the need to do a getpdb on targets- after a LIP for certain the f/w has to do PRLI/PLOGI for all targets again and marking f/w state as unknown gives us a fighting chance to (start to) hold up for that to complete.
1999-04-04 02:28:29 +00:00
*/
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
if (ISP_READ(isp, OUTMAILBOX1) != 0x4953 ||
ISP_READ(isp, OUTMAILBOX2) != 0x5020 ||
ISP_READ(isp, OUTMAILBOX3) != 0x2020) {
/*
* Just in case it was paused...
*/
ISP_WRITE(isp, HCCR, HCCR_CMD_RELEASE);
mbs.param[0] = MBOX_ABOUT_FIRMWARE;
isp_mboxcmd(isp, &mbs, MBLOGNONE);
/*
* This *shouldn't* fail.....
*/
if (mbs.param[0] == MBOX_COMMAND_COMPLETE) {
isp->isp_romfw_rev[0] = mbs.param[1];
isp->isp_romfw_rev[1] = mbs.param[2];
isp->isp_romfw_rev[2] = mbs.param[3];
}
Add some prototype deadchip detection. Set FIFO bursting (1XX0 only- it's already on for the 2XX0) and detect the broken 1040A FIFO. Change bzero to MEMZERO (portability with **nux). Use memcpy for same reason. Finally detect QUEUE FULL conditions and return this as an error that will get cam_periph_error to do it's 'tagged openings now XXX' dance.
1999-01-10 02:55:10 +00:00
}
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
isp->isp_touched = 1;
Add some prototype deadchip detection. Set FIFO bursting (1XX0 only- it's already on for the 2XX0) and detect the broken 1040A FIFO. Change bzero to MEMZERO (portability with **nux). Use memcpy for same reason. Finally detect QUEUE FULL conditions and return this as an error that will get cam_periph_error to do it's 'tagged openings now XXX' dance.
1999-01-10 02:55:10 +00:00
}
Make firmware revision a triple. Clean up some FC init stuff for board versions with no BIOS. Separate mailbox interrupts from IOCB interrupts. Read OUTMAILBOX5 while RISC_INT is active- not after you clear it (potential race condition). Clear out older broken BIG_ENDIAN goop. Don't negotiate narrow/async for LVD busses at startup if already in LVD mode. Note usage of presumptive 1040C revision. For all the LIP, PDB Changed, Loop UP/DOWN async events, mark fw state as unknown as well as marking the need to do a getpdb on targets- after a LIP for certain the f/w has to do PRLI/PLOGI for all targets again and marking f/w state as unknown gives us a fighting chance to (start to) hold up for that to complete.
1999-04-04 02:28:29 +00:00
DISABLE_INTS(isp);
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
/*
Add Dual LVD bus (1280) support
1999-12-16 05:42:02 +00:00
* Put the board into PAUSE mode (so we can read the SXP registers).
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
*/
ISP_WRITE(isp, HCCR, HCCR_CMD_PAUSE);
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
if (IS_FC(isp)) {
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
revname = "2X00";
switch (isp->isp_type) {
case ISP_HA_FC_2100:
revname[1] = '1';
break;
case ISP_HA_FC_2200:
revname[1] = '2';
break;
default:
break;
}
Add Dual LVD bus (1280) support
1999-12-16 05:42:02 +00:00
} else if (IS_1240(isp)) {
sdparam *sdp = isp->isp_param;
revname = "1240";
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
isp->isp_clock = 60;
Add Dual LVD bus (1280) support
1999-12-16 05:42:02 +00:00
sdp->isp_ultramode = 1;
sdp++;
sdp->isp_ultramode = 1;
/*
* XXX: Should probably do some bus sensing.
*/
} else if (IS_ULTRA2(isp)) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
static char *m = "bus %d is in %s Mode";
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
u_int16_t l;
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
sdparam *sdp = isp->isp_param;
Add Dual LVD bus (1280) support
1999-12-16 05:42:02 +00:00
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
isp->isp_clock = 100;
Add Dual LVD bus (1280) support
1999-12-16 05:42:02 +00:00
Restructure nvram reading routine to split out to separate functions for 1020/1X80/12160/2X00- for readability. Add in 12160 (Ultra3) support- but not with PPR just yet. Fix and clarify fetching of return parameter for getting firmware rev which for the 2200 contains the connection topology (Private Loop (NL-port), N-port, FL-port, F-port). Synthesize the connection topology for the 2100 which can only be Private Loop or FL-port. Handle a couple of new async mailbox commands which signify connection in Point-to-Point mode (N-port or F-port) or indicate various toe stubbing getting to same. Approved: jkh@freebsd.org
2000-02-11 19:31:32 +00:00
if (IS_1280(isp))
revname = "1280";
else if (IS_1080(isp))
revname = "1080";
else if (IS_12160(isp))
revname = "12160";
else
revname = "<UNKLVD>";
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
l = ISP_READ(isp, SXP_PINS_DIFF) & ISP1080_MODE_MASK;
switch (l) {
case ISP1080_LVD_MODE:
sdp->isp_lvdmode = 1;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGCONFIG, m, 0, "LVD");
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
break;
case ISP1080_HVD_MODE:
sdp->isp_diffmode = 1;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGCONFIG, m, 0, "Differential");
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
break;
case ISP1080_SE_MODE:
sdp->isp_ultramode = 1;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGCONFIG, m, 0, "Single-Ended");
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
break;
default:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR,
"unknown mode on bus %d (0x%x)", 0, l);
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
break;
}
Add Dual LVD bus (1280) support
1999-12-16 05:42:02 +00:00
Restructure nvram reading routine to split out to separate functions for 1020/1X80/12160/2X00- for readability. Add in 12160 (Ultra3) support- but not with PPR just yet. Fix and clarify fetching of return parameter for getting firmware rev which for the 2200 contains the connection topology (Private Loop (NL-port), N-port, FL-port, F-port). Synthesize the connection topology for the 2100 which can only be Private Loop or FL-port. Handle a couple of new async mailbox commands which signify connection in Point-to-Point mode (N-port or F-port) or indicate various toe stubbing getting to same. Approved: jkh@freebsd.org
2000-02-11 19:31:32 +00:00
if (IS_DUALBUS(isp)) {
Add Dual LVD bus (1280) support
1999-12-16 05:42:02 +00:00
sdp++;
l = ISP_READ(isp, SXP_PINS_DIFF|SXP_BANK1_SELECT);
l &= ISP1080_MODE_MASK;
switch(l) {
case ISP1080_LVD_MODE:
sdp->isp_lvdmode = 1;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGCONFIG, m, 1, "LVD");
Add Dual LVD bus (1280) support
1999-12-16 05:42:02 +00:00
break;
case ISP1080_HVD_MODE:
sdp->isp_diffmode = 1;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGCONFIG,
m, 1, "Differential");
Add Dual LVD bus (1280) support
1999-12-16 05:42:02 +00:00
break;
case ISP1080_SE_MODE:
sdp->isp_ultramode = 1;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGCONFIG,
m, 1, "Single-Ended");
Add Dual LVD bus (1280) support
1999-12-16 05:42:02 +00:00
break;
default:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR,
"unknown mode on bus %d (0x%x)", 1, l);
Add Dual LVD bus (1280) support
1999-12-16 05:42:02 +00:00
break;
}
}
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
} else {
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
sdparam *sdp = isp->isp_param;
Add some prototype deadchip detection. Set FIFO bursting (1XX0 only- it's already on for the 2XX0) and detect the broken 1040A FIFO. Change bzero to MEMZERO (portability with **nux). Use memcpy for same reason. Finally detect QUEUE FULL conditions and return this as an error that will get cam_periph_error to do it's 'tagged openings now XXX' dance.
1999-01-10 02:55:10 +00:00
i = ISP_READ(isp, BIU_CONF0) & BIU_CONF0_HW_MASK;
switch (i) {
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
default:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGALL, "Unknown Chip Type 0x%x", i);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
/* FALLTHROUGH */
case 1:
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
revname = "1020";
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
isp->isp_type = ISP_HA_SCSI_1020;
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
isp->isp_clock = 40;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
break;
case 2:
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
/*
* Some 1020A chips are Ultra Capable, but don't
* run the clock rate up for that unless told to
* do so by the Ultra Capable bits being set.
*/
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
revname = "1020A";
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
isp->isp_type = ISP_HA_SCSI_1020A;
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
isp->isp_clock = 40;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
break;
case 3:
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
revname = "1040";
isp->isp_type = ISP_HA_SCSI_1040;
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
isp->isp_clock = 60;
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case 4:
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
revname = "1040A";
isp->isp_type = ISP_HA_SCSI_1040A;
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
isp->isp_clock = 60;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
break;
case 5:
revname = "1040B";
isp->isp_type = ISP_HA_SCSI_1040B;
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
isp->isp_clock = 60;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
break;
Make firmware revision a triple. Clean up some FC init stuff for board versions with no BIOS. Separate mailbox interrupts from IOCB interrupts. Read OUTMAILBOX5 while RISC_INT is active- not after you clear it (potential race condition). Clear out older broken BIG_ENDIAN goop. Don't negotiate narrow/async for LVD busses at startup if already in LVD mode. Note usage of presumptive 1040C revision. For all the LIP, PDB Changed, Loop UP/DOWN async events, mark fw state as unknown as well as marking the need to do a getpdb on targets- after a LIP for certain the f/w has to do PRLI/PLOGI for all targets again and marking f/w state as unknown gives us a fighting chance to (start to) hold up for that to complete.
1999-04-04 02:28:29 +00:00
case 6:
Add Dual LVD bus (1280) support
1999-12-16 05:42:02 +00:00
revname = "1040C";
Make firmware revision a triple. Clean up some FC init stuff for board versions with no BIOS. Separate mailbox interrupts from IOCB interrupts. Read OUTMAILBOX5 while RISC_INT is active- not after you clear it (potential race condition). Clear out older broken BIG_ENDIAN goop. Don't negotiate narrow/async for LVD busses at startup if already in LVD mode. Note usage of presumptive 1040C revision. For all the LIP, PDB Changed, Loop UP/DOWN async events, mark fw state as unknown as well as marking the need to do a getpdb on targets- after a LIP for certain the f/w has to do PRLI/PLOGI for all targets again and marking f/w state as unknown gives us a fighting chance to (start to) hold up for that to complete.
1999-04-04 02:28:29 +00:00
isp->isp_type = ISP_HA_SCSI_1040C;
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
isp->isp_clock = 60;
Make firmware revision a triple. Clean up some FC init stuff for board versions with no BIOS. Separate mailbox interrupts from IOCB interrupts. Read OUTMAILBOX5 while RISC_INT is active- not after you clear it (potential race condition). Clear out older broken BIG_ENDIAN goop. Don't negotiate narrow/async for LVD busses at startup if already in LVD mode. Note usage of presumptive 1040C revision. For all the LIP, PDB Changed, Loop UP/DOWN async events, mark fw state as unknown as well as marking the need to do a getpdb on targets- after a LIP for certain the f/w has to do PRLI/PLOGI for all targets again and marking f/w state as unknown gives us a fighting chance to (start to) hold up for that to complete.
1999-04-04 02:28:29 +00:00
break;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
/*
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
* Now, while we're at it, gather info about ultra
* and/or differential mode.
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
*/
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
if (ISP_READ(isp, SXP_PINS_DIFF) & SXP_PINS_DIFF_MODE) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGCONFIG, "Differential Mode");
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
sdp->isp_diffmode = 1;
Add some prototype deadchip detection. Set FIFO bursting (1XX0 only- it's already on for the 2XX0) and detect the broken 1040A FIFO. Change bzero to MEMZERO (portability with **nux). Use memcpy for same reason. Finally detect QUEUE FULL conditions and return this as an error that will get cam_periph_error to do it's 'tagged openings now XXX' dance.
1999-01-10 02:55:10 +00:00
} else {
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
sdp->isp_diffmode = 0;
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
}
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
i = ISP_READ(isp, RISC_PSR);
if (isp->isp_bustype == ISP_BT_SBUS) {
i &= RISC_PSR_SBUS_ULTRA;
} else {
i &= RISC_PSR_PCI_ULTRA;
}
if (i != 0) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGCONFIG, "Ultra Mode Capable");
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
sdp->isp_ultramode = 1;
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
/*
* If we're in Ultra Mode, we have to be 60Mhz clock-
* even for the SBus version.
*/
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
isp->isp_clock = 60;
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
} else {
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
sdp->isp_ultramode = 0;
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
/*
* Clock is known. Gronk.
*/
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
}
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
/*
* Machine dependent clock (if set) overrides
* our generic determinations.
*/
if (isp->isp_mdvec->dv_clock) {
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
if (isp->isp_mdvec->dv_clock < isp->isp_clock) {
isp->isp_clock = isp->isp_mdvec->dv_clock;
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
}
}
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
/*
* Do MD specific pre initialization
*/
ISP_RESET0(isp);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
again:
Add some prototype deadchip detection. Set FIFO bursting (1XX0 only- it's already on for the 2XX0) and detect the broken 1040A FIFO. Change bzero to MEMZERO (portability with **nux). Use memcpy for same reason. Finally detect QUEUE FULL conditions and return this as an error that will get cam_periph_error to do it's 'tagged openings now XXX' dance.
1999-01-10 02:55:10 +00:00
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
/*
* Hit the chip over the head with hammer,
* and give the ISP a chance to recover.
*/
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
if (IS_SCSI(isp)) {
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
ISP_WRITE(isp, BIU_ICR, BIU_ICR_SOFT_RESET);
/*
* A slight delay...
*/
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
USEC_DELAY(100);
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
/*
* Clear data && control DMA engines.
*/
ISP_WRITE(isp, CDMA_CONTROL,
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
DMA_CNTRL_CLEAR_CHAN | DMA_CNTRL_RESET_INT);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
ISP_WRITE(isp, DDMA_CONTROL,
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
DMA_CNTRL_CLEAR_CHAN | DMA_CNTRL_RESET_INT);
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
} else {
ISP_WRITE(isp, BIU2100_CSR, BIU2100_SOFT_RESET);
/*
* A slight delay...
*/
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
USEC_DELAY(100);
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
/*
* Clear data && control DMA engines.
*/
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
ISP_WRITE(isp, CDMA2100_CONTROL,
DMA_CNTRL2100_CLEAR_CHAN | DMA_CNTRL2100_RESET_INT);
ISP_WRITE(isp, TDMA2100_CONTROL,
DMA_CNTRL2100_CLEAR_CHAN | DMA_CNTRL2100_RESET_INT);
ISP_WRITE(isp, RDMA2100_CONTROL,
DMA_CNTRL2100_CLEAR_CHAN | DMA_CNTRL2100_RESET_INT);
}
/*
* Wait for ISP to be ready to go...
*/
loops = MBOX_DELAY_COUNT;
for (;;) {
More code cleanup. Go back to using FULL_LOGIN Fibre Chan if f/w is less than 1.17.0 level. Change where we do the loop database init. Add in the CMD_RQLATER return. Add some register debounce.
1999-08-16 19:59:55 +00:00
if (IS_SCSI(isp)) {
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
if (!(ISP_READ(isp, BIU_ICR) & BIU_ICR_SOFT_RESET))
break;
} else {
if (!(ISP_READ(isp, BIU2100_CSR) & BIU2100_SOFT_RESET))
break;
}
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
USEC_DELAY(100);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
if (--loops < 0) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
ISP_DUMPREGS(isp, "chip reset timed out");
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
return;
}
}
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
/*
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
* After we've fired this chip up, zero out the conf1 register
* for SCSI adapters and other settings for the 2100.
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
*/
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
if (IS_SCSI(isp)) {
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
ISP_WRITE(isp, BIU_CONF1, 0);
} else {
ISP_WRITE(isp, BIU2100_CSR, 0);
}
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
/*
* Reset RISC Processor
*/
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
ISP_WRITE(isp, HCCR, HCCR_CMD_RESET);
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
USEC_DELAY(100);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
Add some prototype deadchip detection. Set FIFO bursting (1XX0 only- it's already on for the 2XX0) and detect the broken 1040A FIFO. Change bzero to MEMZERO (portability with **nux). Use memcpy for same reason. Finally detect QUEUE FULL conditions and return this as an error that will get cam_periph_error to do it's 'tagged openings now XXX' dance.
1999-01-10 02:55:10 +00:00
/*
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
* Establish some initial burst rate stuff.
Add some prototype deadchip detection. Set FIFO bursting (1XX0 only- it's already on for the 2XX0) and detect the broken 1040A FIFO. Change bzero to MEMZERO (portability with **nux). Use memcpy for same reason. Finally detect QUEUE FULL conditions and return this as an error that will get cam_periph_error to do it's 'tagged openings now XXX' dance.
1999-01-10 02:55:10 +00:00
* (only for the 1XX0 boards). This really should
* be done later after fetching from NVRAM.
*/
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
if (IS_SCSI(isp)) {
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
u_int16_t tmp = isp->isp_mdvec->dv_conf1;
Add some prototype deadchip detection. Set FIFO bursting (1XX0 only- it's already on for the 2XX0) and detect the broken 1040A FIFO. Change bzero to MEMZERO (portability with **nux). Use memcpy for same reason. Finally detect QUEUE FULL conditions and return this as an error that will get cam_periph_error to do it's 'tagged openings now XXX' dance.
1999-01-10 02:55:10 +00:00
/*
* Busted FIFO. Turn off all but burst enables.
*/
if (isp->isp_type == ISP_HA_SCSI_1040A) {
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
tmp &= BIU_BURST_ENABLE;
Add some prototype deadchip detection. Set FIFO bursting (1XX0 only- it's already on for the 2XX0) and detect the broken 1040A FIFO. Change bzero to MEMZERO (portability with **nux). Use memcpy for same reason. Finally detect QUEUE FULL conditions and return this as an error that will get cam_periph_error to do it's 'tagged openings now XXX' dance.
1999-01-10 02:55:10 +00:00
}
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
ISP_SETBITS(isp, BIU_CONF1, tmp);
if (tmp & BIU_BURST_ENABLE) {
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
ISP_SETBITS(isp, CDMA_CONF, DMA_ENABLE_BURST);
ISP_SETBITS(isp, DDMA_CONF, DMA_ENABLE_BURST);
}
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
#ifdef PTI_CARDS
if (((sdparam *) isp->isp_param)->isp_ultramode) {
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
while (ISP_READ(isp, RISC_MTR) != 0x1313) {
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
ISP_WRITE(isp, RISC_MTR, 0x1313);
ISP_WRITE(isp, HCCR, HCCR_CMD_STEP);
}
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
} else {
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
ISP_WRITE(isp, RISC_MTR, 0x1212);
}
/*
* PTI specific register
*/
ISP_WRITE(isp, RISC_EMB, DUAL_BANK)
#else
ISP_WRITE(isp, RISC_MTR, 0x1212);
#endif
} else {
ISP_WRITE(isp, RISC_MTR2100, 0x1212);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
ISP_WRITE(isp, HCCR, HCCR_CMD_RELEASE); /* release paused processor */
/*
* Do MD specific post initialization
*/
ISP_RESET1(isp);
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
/*
* Wait for everything to finish firing up...
*/
loops = MBOX_DELAY_COUNT;
while (ISP_READ(isp, OUTMAILBOX0) == MBOX_BUSY) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
USEC_DELAY(100);
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
if (--loops < 0) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR,
"MBOX_BUSY never cleared on reset");
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
return;
}
}
/*
* Up until this point we've done everything by just reading or
* setting registers. From this point on we rely on at least *some*
* kind of firmware running in the card.
*/
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
/*
* Do some sanity checking.
*/
mbs.param[0] = MBOX_NO_OP;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGALL);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
if (mbs.param[0] != MBOX_COMMAND_COMPLETE) {
return;
}
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
if (IS_SCSI(isp)) {
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
mbs.param[0] = MBOX_MAILBOX_REG_TEST;
mbs.param[1] = 0xdead;
mbs.param[2] = 0xbeef;
mbs.param[3] = 0xffff;
mbs.param[4] = 0x1111;
mbs.param[5] = 0xa5a5;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGALL);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
if (mbs.param[0] != MBOX_COMMAND_COMPLETE) {
return;
}
if (mbs.param[1] != 0xdead || mbs.param[2] != 0xbeef ||
mbs.param[3] != 0xffff || mbs.param[4] != 0x1111 ||
mbs.param[5] != 0xa5a5) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR,
"Register Test Failed (0x%x 0x%x 0x%x 0x%x 0x%x)",
mbs.param[1], mbs.param[2], mbs.param[3],
mbs.param[4], mbs.param[5]);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
return;
}
}
/*
* Download new Firmware, unless requested not to do so.
* This is made slightly trickier in some cases where the
* firmware of the ROM revision is newer than the revision
* compiled into the driver. So, where we used to compare
* versions of our f/w and the ROM f/w, now we just see
* whether we have f/w at all and whether a config flag
* has disabled our download.
*/
correct moronic typo
1999-11-01 04:39:52 +00:00
if ((isp->isp_mdvec->dv_ispfw == NULL) ||
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
(isp->isp_confopts & ISP_CFG_NORELOAD)) {
dodnld = 0;
}
correct moronic typo
1999-11-01 04:39:52 +00:00
if (dodnld) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
u_int16_t fwlen = isp->isp_mdvec->dv_ispfw[3];
Use pointer to f/w in md structure as to whether f/w exists or not. If firmware length isn't specified, extract from the 4th short into the firmware.
1999-10-30 19:32:44 +00:00
for (i = 0; i < fwlen; i++) {
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
mbs.param[0] = MBOX_WRITE_RAM_WORD;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
mbs.param[1] = ISP_CODE_ORG + i;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
mbs.param[2] = isp->isp_mdvec->dv_ispfw[i];
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGNONE);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
if (mbs.param[0] != MBOX_COMMAND_COMPLETE) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR,
"F/W download failed at word %d", i);
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
dodnld = 0;
goto again;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
}
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
/*
* Verify that it downloaded correctly.
*/
mbs.param[0] = MBOX_VERIFY_CHECKSUM;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
mbs.param[1] = ISP_CODE_ORG;
isp_mboxcmd(isp, &mbs, MBLOGNONE);
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
if (mbs.param[0] != MBOX_COMMAND_COMPLETE) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR, "Ram Checksum Failure");
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
return;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
various fixes
2000-08-27 23:38:44 +00:00
isp->isp_loaded_fw = 1;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
} else {
various fixes
2000-08-27 23:38:44 +00:00
isp->isp_loaded_fw = 0;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGDEBUG2, "skipping f/w download");
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
/*
* Now start it rolling.
*
* If we didn't actually download f/w,
* we still need to (re)start it.
*/
mbs.param[0] = MBOX_EXEC_FIRMWARE;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
mbs.param[1] = ISP_CODE_ORG;
isp_mboxcmd(isp, &mbs, MBLOGNONE);
Once we have firmware running (if isp_reset) and this is the first time through, establish what our LUN width is. Unfortunately, we can't ask the f/w. If we loaded the f/w, we'll now assume we have expanded LUNs (SCCLUN for fibre channel, just plain 32 LUN for SCSI). If we didn't load firmware, assume 8 LUNs for SCSI and 1 LUN for Fibre Channel. We have to assume only one LUN for Fibre Channel because the LUN setting in Request Queue entries is in different places whether we have SCCLUN firmware or not, so the only LUN guaranteed to work for both is LUN 0. Clean up the rest of isp.c so that ISP2100_SCCLUN defines aren't used- instead use run time determinants based upon isp->isp_maxluns. After starting firmware, delay 500us to give it a chance to get rolling. Fix the interrupt service routine to check for both isr && sema being zero before thinking this was a spurious interrupt. Following the manuals, allow for both Mailbox as well as Queue Reponse type interrupts for regular SCSI.
2000-06-18 04:56:17 +00:00
/* give it a chance to start */
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
USEC_DELAY(500);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
More code cleanup. Go back to using FULL_LOGIN Fibre Chan if f/w is less than 1.17.0 level. Change where we do the loop database init. Add in the CMD_RQLATER return. Add some register debounce.
1999-08-16 19:59:55 +00:00
if (IS_SCSI(isp)) {
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
/*
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
* Set CLOCK RATE, but only if asked to.
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
*/
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
if (isp->isp_clock) {
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
mbs.param[0] = MBOX_SET_CLOCK_RATE;
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
mbs.param[1] = isp->isp_clock;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGALL);
/* we will try not to care if this fails */
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
}
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
mbs.param[0] = MBOX_ABOUT_FIRMWARE;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGALL);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
if (mbs.param[0] != MBOX_COMMAND_COMPLETE) {
return;
}
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGCONFIG,
"Board Revision %s, %s F/W Revision %d.%d.%d", revname,
dodnld? "loaded" : "resident", mbs.param[1], mbs.param[2],
mbs.param[3]);
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
if (IS_FC(isp)) {
Roll internal release tag. Print out if we're in a 64 bit PCI slot. Use fast memory timing NVRAM parameter. Clean up and fix establishment of default target parameters. Don't use NVRAM if are flagged as not to do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC mode but disabled disconnect/reconnect and wide!!). Fix delays after resets. BUS resets not done in isp_init anymore- relegated to OS specific outer layers. Fix a buglet where you can get in a loop for a NULL xs in the completion list in isp_intr. Add in some defines that can disable fast posting. Add in code for Loop Up/Loop Down events that call into the outer layers as to what to do.
1999-02-09 01:07:06 +00:00
if (ISP_READ(isp, BIU2100_CSR) & BIU2100_PCI64) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGCONFIG,
"Installed in 64-Bit PCI slot");
Roll internal release tag. Print out if we're in a 64 bit PCI slot. Use fast memory timing NVRAM parameter. Clean up and fix establishment of default target parameters. Don't use NVRAM if are flagged as not to do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC mode but disabled disconnect/reconnect and wide!!). Fix delays after resets. BUS resets not done in isp_init anymore- relegated to OS specific outer layers. Fix a buglet where you can get in a loop for a NULL xs in the completion list in isp_intr. Add in some defines that can disable fast posting. Add in code for Loop Up/Loop Down events that call into the outer layers as to what to do.
1999-02-09 01:07:06 +00:00
}
}
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
Make firmware revision a triple. Clean up some FC init stuff for board versions with no BIOS. Separate mailbox interrupts from IOCB interrupts. Read OUTMAILBOX5 while RISC_INT is active- not after you clear it (potential race condition). Clear out older broken BIG_ENDIAN goop. Don't negotiate narrow/async for LVD busses at startup if already in LVD mode. Note usage of presumptive 1040C revision. For all the LIP, PDB Changed, Loop UP/DOWN async events, mark fw state as unknown as well as marking the need to do a getpdb on targets- after a LIP for certain the f/w has to do PRLI/PLOGI for all targets again and marking f/w state as unknown gives us a fighting chance to (start to) hold up for that to complete.
1999-04-04 02:28:29 +00:00
isp->isp_fwrev[0] = mbs.param[1];
isp->isp_fwrev[1] = mbs.param[2];
isp->isp_fwrev[2] = mbs.param[3];
if (isp->isp_romfw_rev[0] || isp->isp_romfw_rev[1] ||
isp->isp_romfw_rev[2]) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGCONFIG, "Last F/W revision was %d.%d.%d",
Make firmware revision a triple. Clean up some FC init stuff for board versions with no BIOS. Separate mailbox interrupts from IOCB interrupts. Read OUTMAILBOX5 while RISC_INT is active- not after you clear it (potential race condition). Clear out older broken BIG_ENDIAN goop. Don't negotiate narrow/async for LVD busses at startup if already in LVD mode. Note usage of presumptive 1040C revision. For all the LIP, PDB Changed, Loop UP/DOWN async events, mark fw state as unknown as well as marking the need to do a getpdb on targets- after a LIP for certain the f/w has to do PRLI/PLOGI for all targets again and marking f/w state as unknown gives us a fighting chance to (start to) hold up for that to complete.
1999-04-04 02:28:29 +00:00
isp->isp_romfw_rev[0], isp->isp_romfw_rev[1],
isp->isp_romfw_rev[2]);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
}
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
mbs.param[0] = MBOX_GET_FIRMWARE_STATUS;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGALL);
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
if (mbs.param[0] != MBOX_COMMAND_COMPLETE) {
return;
}
isp->isp_maxcmds = mbs.param[2];
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGINFO,
"%d max I/O commands supported", mbs.param[2]);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
isp_fw_state(isp);
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
/*
* Set up DMA for the request and result mailboxes.
*/
if (ISP_MBOXDMASETUP(isp) != 0) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR, "Cannot setup DMA");
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
return;
}
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
isp->isp_state = ISP_RESETSTATE;
Once we have firmware running (if isp_reset) and this is the first time through, establish what our LUN width is. Unfortunately, we can't ask the f/w. If we loaded the f/w, we'll now assume we have expanded LUNs (SCCLUN for fibre channel, just plain 32 LUN for SCSI). If we didn't load firmware, assume 8 LUNs for SCSI and 1 LUN for Fibre Channel. We have to assume only one LUN for Fibre Channel because the LUN setting in Request Queue entries is in different places whether we have SCCLUN firmware or not, so the only LUN guaranteed to work for both is LUN 0. Clean up the rest of isp.c so that ISP2100_SCCLUN defines aren't used- instead use run time determinants based upon isp->isp_maxluns. After starting firmware, delay 500us to give it a chance to get rolling. Fix the interrupt service routine to check for both isr && sema being zero before thinking this was a spurious interrupt. Following the manuals, allow for both Mailbox as well as Queue Reponse type interrupts for regular SCSI.
2000-06-18 04:56:17 +00:00
/*
* Okay- now that we have new firmware running, we now (re)set our
* notion of how many luns we support. This is somewhat tricky because
* if we haven't loaded firmware, we don't have an easy way of telling
* how many luns we support.
*
* We'll make a simplifying assumption- if we loaded firmware, we
* are running with expanded lun firmware, otherwise not.
*
* Expanded lun firmware gives you 32 luns for SCSI cards and
* 65536 luns for Fibre Channel cards.
*
* Because the lun is in a a different position in the Request Queue
* Entry structure for Fibre Channel with expanded lun firmware, we
* can only support one lun (lun zero) when we don't know what kind
* of firmware we're running.
*
* Note that we only do this once (the first time thru isp_reset)
* because we may be called again after firmware has been loaded once
* and released.
*/
if (touched == 0) {
if (dodnld) {
if (IS_SCSI(isp)) {
isp->isp_maxluns = 32;
} else {
isp->isp_maxluns = 65536;
}
} else {
if (IS_SCSI(isp)) {
isp->isp_maxluns = 8;
} else {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGALL, warnlun);
Once we have firmware running (if isp_reset) and this is the first time through, establish what our LUN width is. Unfortunately, we can't ask the f/w. If we loaded the f/w, we'll now assume we have expanded LUNs (SCCLUN for fibre channel, just plain 32 LUN for SCSI). If we didn't load firmware, assume 8 LUNs for SCSI and 1 LUN for Fibre Channel. We have to assume only one LUN for Fibre Channel because the LUN setting in Request Queue entries is in different places whether we have SCCLUN firmware or not, so the only LUN guaranteed to work for both is LUN 0. Clean up the rest of isp.c so that ISP2100_SCCLUN defines aren't used- instead use run time determinants based upon isp->isp_maxluns. After starting firmware, delay 500us to give it a chance to get rolling. Fix the interrupt service routine to check for both isr && sema being zero before thinking this was a spurious interrupt. Following the manuals, allow for both Mailbox as well as Queue Reponse type interrupts for regular SCSI.
2000-06-18 04:56:17 +00:00
isp->isp_maxluns = 1;
}
}
}
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
/*
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
* Initialize Parameters of Hardware to a known state.
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
*
* Locks are held before coming here.
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
*/
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
void
isp_init(isp)
struct ispsoftc *isp;
{
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
/*
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
* Must do this first to get defaults established.
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
*/
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
isp_setdfltparm(isp, 0);
Add Dual LVD bus (1280) support
1999-12-16 05:42:02 +00:00
if (IS_DUALBUS(isp)) {
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
isp_setdfltparm(isp, 1);
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
}
if (IS_FC(isp)) {
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
isp_fibre_init(isp);
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
} else {
isp_scsi_init(isp);
}
}
static void
isp_scsi_init(isp)
struct ispsoftc *isp;
{
sdparam *sdp_chan0, *sdp_chan1;
mbreg_t mbs;
sdp_chan0 = isp->isp_param;
sdp_chan1 = sdp_chan0;
Add Dual LVD bus (1280) support
1999-12-16 05:42:02 +00:00
if (IS_DUALBUS(isp)) {
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
sdp_chan1++;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
/* First do overall per-card settings. */
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
Roll internal release tag. Print out if we're in a 64 bit PCI slot. Use fast memory timing NVRAM parameter. Clean up and fix establishment of default target parameters. Don't use NVRAM if are flagged as not to do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC mode but disabled disconnect/reconnect and wide!!). Fix delays after resets. BUS resets not done in isp_init anymore- relegated to OS specific outer layers. Fix a buglet where you can get in a loop for a NULL xs in the completion list in isp_intr. Add in some defines that can disable fast posting. Add in code for Loop Up/Loop Down events that call into the outer layers as to what to do.
1999-02-09 01:07:06 +00:00
/*
* If we have fast memory timing enabled, turn it on.
*/
various fixes
2000-08-27 23:38:44 +00:00
if (sdp_chan0->isp_fast_mttr) {
Roll internal release tag. Print out if we're in a 64 bit PCI slot. Use fast memory timing NVRAM parameter. Clean up and fix establishment of default target parameters. Don't use NVRAM if are flagged as not to do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC mode but disabled disconnect/reconnect and wide!!). Fix delays after resets. BUS resets not done in isp_init anymore- relegated to OS specific outer layers. Fix a buglet where you can get in a loop for a NULL xs in the completion list in isp_intr. Add in some defines that can disable fast posting. Add in code for Loop Up/Loop Down events that call into the outer layers as to what to do.
1999-02-09 01:07:06 +00:00
ISP_WRITE(isp, RISC_MTR, 0x1313);
}
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
/*
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
* Set Retry Delay and Count.
* You set both channels at the same time.
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
*/
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
mbs.param[0] = MBOX_SET_RETRY_COUNT;
mbs.param[1] = sdp_chan0->isp_retry_count;
mbs.param[2] = sdp_chan0->isp_retry_delay;
mbs.param[6] = sdp_chan1->isp_retry_count;
mbs.param[7] = sdp_chan1->isp_retry_delay;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGALL);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
if (mbs.param[0] != MBOX_COMMAND_COMPLETE) {
return;
}
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
/*
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
* Set ASYNC DATA SETUP time. This is very important.
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
*/
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
mbs.param[0] = MBOX_SET_ASYNC_DATA_SETUP_TIME;
mbs.param[1] = sdp_chan0->isp_async_data_setup;
mbs.param[2] = sdp_chan1->isp_async_data_setup;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGALL);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
if (mbs.param[0] != MBOX_COMMAND_COMPLETE) {
return;
}
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
/*
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
* Set ACTIVE Negation State.
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
*/
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
mbs.param[0] = MBOX_SET_ACT_NEG_STATE;
mbs.param[1] =
(sdp_chan0->isp_req_ack_active_neg << 4) |
(sdp_chan0->isp_data_line_active_neg << 5);
mbs.param[2] =
(sdp_chan1->isp_req_ack_active_neg << 4) |
(sdp_chan1->isp_data_line_active_neg << 5);
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGNONE);
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
if (mbs.param[0] != MBOX_COMMAND_COMPLETE) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR,
"failed to set active negation state (%d,%d), (%d,%d)",
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
sdp_chan0->isp_req_ack_active_neg,
sdp_chan0->isp_data_line_active_neg,
sdp_chan1->isp_req_ack_active_neg,
sdp_chan1->isp_data_line_active_neg);
/*
* But don't return.
*/
}
/*
* Set the Tag Aging limit
*/
mbs.param[0] = MBOX_SET_TAG_AGE_LIMIT;
mbs.param[1] = sdp_chan0->isp_tag_aging;
mbs.param[2] = sdp_chan1->isp_tag_aging;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGALL);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
if (mbs.param[0] != MBOX_COMMAND_COMPLETE) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR, "failed to set tag age limit (%d,%d)",
sdp_chan0->isp_tag_aging, sdp_chan1->isp_tag_aging);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
return;
}
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
/*
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
* Set selection timeout.
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
*/
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
mbs.param[0] = MBOX_SET_SELECT_TIMEOUT;
mbs.param[1] = sdp_chan0->isp_selection_timeout;
mbs.param[2] = sdp_chan1->isp_selection_timeout;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGALL);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
if (mbs.param[0] != MBOX_COMMAND_COMPLETE) {
return;
}
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
/* now do per-channel settings */
isp_scsi_channel_init(isp, 0);
Add Dual LVD bus (1280) support
1999-12-16 05:42:02 +00:00
if (IS_DUALBUS(isp))
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
isp_scsi_channel_init(isp, 1);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
/*
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
* Now enable request/response queues
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
*/
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
mbs.param[0] = MBOX_INIT_RES_QUEUE;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
mbs.param[1] = RESULT_QUEUE_LEN(isp);
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
mbs.param[2] = DMA_MSW(isp->isp_result_dma);
mbs.param[3] = DMA_LSW(isp->isp_result_dma);
mbs.param[4] = 0;
mbs.param[5] = 0;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGALL);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
if (mbs.param[0] != MBOX_COMMAND_COMPLETE) {
return;
}
Inintialize the queue index stuff from what the f/w sends back- just in case it's insane enough to not do what you tell it to. Print out (LOGINFO level) initiator ID.
2000-09-21 17:06:45 +00:00
isp->isp_residx = mbs.param[5];
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
mbs.param[0] = MBOX_INIT_REQ_QUEUE;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
mbs.param[1] = RQUEST_QUEUE_LEN(isp);
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
mbs.param[2] = DMA_MSW(isp->isp_rquest_dma);
mbs.param[3] = DMA_LSW(isp->isp_rquest_dma);
mbs.param[4] = 0;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGALL);
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
if (mbs.param[0] != MBOX_COMMAND_COMPLETE) {
return;
}
Inintialize the queue index stuff from what the f/w sends back- just in case it's insane enough to not do what you tell it to. Print out (LOGINFO level) initiator ID.
2000-09-21 17:06:45 +00:00
isp->isp_reqidx = isp->isp_reqodx = mbs.param[4];
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
/*
Clean up some f/w revision checking wrt enabling fast posting. Make sure we set defaults sanely for dual-bus adapters.
1999-12-20 01:34:01 +00:00
* Turn on Fast Posting, LVD transitions
*
* Ultra2 F/W always has had fast posting (and LVD transitions)
*
Clean out residual bogosity for fast posting stuff- ISP_NO_FASTPOST_SCSI is gone as a define. We just don't support fast posting for anything less than the 1240/1080/1280/12160 or Fibre Channel cards. Put in support for CDB's larger than 12 bytes for parallel SCSI (up to 44 bytes are allowed). Approved: jkh
2000-02-15 00:35:00 +00:00
* Ultra and older (i.e., SBus) cards may not. It's just safer
* to assume not for them.
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
*/
Clean up some f/w revision checking wrt enabling fast posting. Make sure we set defaults sanely for dual-bus adapters.
1999-12-20 01:34:01 +00:00
mbs.param[0] = MBOX_SET_FW_FEATURES;
mbs.param[1] = 0;
if (IS_ULTRA2(isp))
mbs.param[1] |= FW_FEATURE_LVD_NOTIFY;
Restructure nvram reading routine to split out to separate functions for 1020/1X80/12160/2X00- for readability. Add in 12160 (Ultra3) support- but not with PPR just yet. Fix and clarify fetching of return parameter for getting firmware rev which for the 2200 contains the connection topology (Private Loop (NL-port), N-port, FL-port, F-port). Synthesize the connection topology for the 2100 which can only be Private Loop or FL-port. Handle a couple of new async mailbox commands which signify connection in Point-to-Point mode (N-port or F-port) or indicate various toe stubbing getting to same. Approved: jkh@freebsd.org
2000-02-11 19:31:32 +00:00
if (IS_ULTRA2(isp) || IS_1240(isp))
mbs.param[1] |= FW_FEATURE_FAST_POST;
Clean up some f/w revision checking wrt enabling fast posting. Make sure we set defaults sanely for dual-bus adapters.
1999-12-20 01:34:01 +00:00
if (mbs.param[1] != 0) {
u_int16_t sfeat = mbs.param[1];
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGALL);
if (mbs.param[0] == MBOX_COMMAND_COMPLETE) {
isp_prt(isp, ISP_LOGINFO,
"Enabled FW features (0x%x)", sfeat);
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
}
}
/*
* Let the outer layers decide whether to issue a SCSI bus reset.
*/
isp->isp_state = ISP_INITSTATE;
}
static void
isp_scsi_channel_init(isp, channel)
struct ispsoftc *isp;
int channel;
{
sdparam *sdp;
mbreg_t mbs;
int tgt;
sdp = isp->isp_param;
sdp += channel;
/*
* Set (possibly new) Initiator ID.
*/
mbs.param[0] = MBOX_SET_INIT_SCSI_ID;
mbs.param[1] = (channel << 7) | sdp->isp_initiator_id;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGALL);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
if (mbs.param[0] != MBOX_COMMAND_COMPLETE) {
return;
}
Inintialize the queue index stuff from what the f/w sends back- just in case it's insane enough to not do what you tell it to. Print out (LOGINFO level) initiator ID.
2000-09-21 17:06:45 +00:00
isp_prt(isp, ISP_LOGINFO, "Initiator ID is %d", sdp->isp_initiator_id);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
/*
Roll internal release tag. Print out if we're in a 64 bit PCI slot. Use fast memory timing NVRAM parameter. Clean up and fix establishment of default target parameters. Don't use NVRAM if are flagged as not to do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC mode but disabled disconnect/reconnect and wide!!). Fix delays after resets. BUS resets not done in isp_init anymore- relegated to OS specific outer layers. Fix a buglet where you can get in a loop for a NULL xs in the completion list in isp_intr. Add in some defines that can disable fast posting. Add in code for Loop Up/Loop Down events that call into the outer layers as to what to do.
1999-02-09 01:07:06 +00:00
* Set current per-target parameters to a safe minimum.
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
*/
for (tgt = 0; tgt < MAX_TARGETS; tgt++) {
Once we have firmware running (if isp_reset) and this is the first time through, establish what our LUN width is. Unfortunately, we can't ask the f/w. If we loaded the f/w, we'll now assume we have expanded LUNs (SCCLUN for fibre channel, just plain 32 LUN for SCSI). If we didn't load firmware, assume 8 LUNs for SCSI and 1 LUN for Fibre Channel. We have to assume only one LUN for Fibre Channel because the LUN setting in Request Queue entries is in different places whether we have SCCLUN firmware or not, so the only LUN guaranteed to work for both is LUN 0. Clean up the rest of isp.c so that ISP2100_SCCLUN defines aren't used- instead use run time determinants based upon isp->isp_maxluns. After starting firmware, delay 500us to give it a chance to get rolling. Fix the interrupt service routine to check for both isr && sema being zero before thinking this was a spurious interrupt. Following the manuals, allow for both Mailbox as well as Queue Reponse type interrupts for regular SCSI.
2000-06-18 04:56:17 +00:00
int lun;
Roll internal release tag. Print out if we're in a 64 bit PCI slot. Use fast memory timing NVRAM parameter. Clean up and fix establishment of default target parameters. Don't use NVRAM if are flagged as not to do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC mode but disabled disconnect/reconnect and wide!!). Fix delays after resets. BUS resets not done in isp_init anymore- relegated to OS specific outer layers. Fix a buglet where you can get in a loop for a NULL xs in the completion list in isp_intr. Add in some defines that can disable fast posting. Add in code for Loop Up/Loop Down events that call into the outer layers as to what to do.
1999-02-09 01:07:06 +00:00
u_int16_t sdf;
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
if (sdp->isp_devparam[tgt].dev_enable == 0) {
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
continue;
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
}
various fixes
2000-08-27 23:38:44 +00:00
sdf = DPARM_SAFE_DFLT;
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
/*
various fixes
2000-08-27 23:38:44 +00:00
* It is not quite clear when this changed over so that
* we could force narrow and async for 1000/1020 cards,
* but assume that this is only the case for loaded
* firmware.
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
*/
various fixes
2000-08-27 23:38:44 +00:00
if (isp->isp_loaded_fw) {
sdf |= DPARM_NARROW | DPARM_ASYNC;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
Roll internal release tag. Print out if we're in a 64 bit PCI slot. Use fast memory timing NVRAM parameter. Clean up and fix establishment of default target parameters. Don't use NVRAM if are flagged as not to do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC mode but disabled disconnect/reconnect and wide!!). Fix delays after resets. BUS resets not done in isp_init anymore- relegated to OS specific outer layers. Fix a buglet where you can get in a loop for a NULL xs in the completion list in isp_intr. Add in some defines that can disable fast posting. Add in code for Loop Up/Loop Down events that call into the outer layers as to what to do.
1999-02-09 01:07:06 +00:00
mbs.param[0] = MBOX_SET_TARGET_PARAMS;
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
mbs.param[1] = (tgt << 8) | (channel << 15);
Roll internal release tag. Print out if we're in a 64 bit PCI slot. Use fast memory timing NVRAM parameter. Clean up and fix establishment of default target parameters. Don't use NVRAM if are flagged as not to do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC mode but disabled disconnect/reconnect and wide!!). Fix delays after resets. BUS resets not done in isp_init anymore- relegated to OS specific outer layers. Fix a buglet where you can get in a loop for a NULL xs in the completion list in isp_intr. Add in some defines that can disable fast posting. Add in code for Loop Up/Loop Down events that call into the outer layers as to what to do.
1999-02-09 01:07:06 +00:00
mbs.param[2] = sdf;
various fixes
2000-08-27 23:38:44 +00:00
if ((sdf & DPARM_SYNC) == 0) {
mbs.param[3] = 0;
} else {
mbs.param[3] =
(sdp->isp_devparam[tgt].sync_offset << 8) |
(sdp->isp_devparam[tgt].sync_period);
}
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGALL);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
if (mbs.param[0] != MBOX_COMMAND_COMPLETE) {
Roll internal release tag. Print out if we're in a 64 bit PCI slot. Use fast memory timing NVRAM parameter. Clean up and fix establishment of default target parameters. Don't use NVRAM if are flagged as not to do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC mode but disabled disconnect/reconnect and wide!!). Fix delays after resets. BUS resets not done in isp_init anymore- relegated to OS specific outer layers. Fix a buglet where you can get in a loop for a NULL xs in the completion list in isp_intr. Add in some defines that can disable fast posting. Add in code for Loop Up/Loop Down events that call into the outer layers as to what to do.
1999-02-09 01:07:06 +00:00
sdf = DPARM_SAFE_DFLT;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
mbs.param[0] = MBOX_SET_TARGET_PARAMS;
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
mbs.param[1] = (tgt << 8) | (channel << 15);
Roll internal release tag. Print out if we're in a 64 bit PCI slot. Use fast memory timing NVRAM parameter. Clean up and fix establishment of default target parameters. Don't use NVRAM if are flagged as not to do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC mode but disabled disconnect/reconnect and wide!!). Fix delays after resets. BUS resets not done in isp_init anymore- relegated to OS specific outer layers. Fix a buglet where you can get in a loop for a NULL xs in the completion list in isp_intr. Add in some defines that can disable fast posting. Add in code for Loop Up/Loop Down events that call into the outer layers as to what to do.
1999-02-09 01:07:06 +00:00
mbs.param[2] = sdf;
various fixes
2000-08-27 23:38:44 +00:00
mbs.param[3] = 0;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGALL);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
if (mbs.param[0] != MBOX_COMMAND_COMPLETE) {
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
continue;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
}
Clean up some f/w revision checking wrt enabling fast posting. Make sure we set defaults sanely for dual-bus adapters.
1999-12-20 01:34:01 +00:00
Annoying little nigglet- apparently *some* Qlogic temporarily ignore settings you've just sent them and return random values if you follow the set by a get. This causes problems when you latter run a Tag-enabled command when you've command tagged mode off.
1999-03-26 00:33:13 +00:00
/*
various fixes
2000-08-27 23:38:44 +00:00
* We don't update any information directly from the f/w
* because we need to run at least one command to cause a
* new state to be latched up. So, we just assume that we
* converge to the values we just had set.
*
Annoying little nigglet- apparently *some* Qlogic temporarily ignore settings you've just sent them and return random values if you follow the set by a get. This causes problems when you latter run a Tag-enabled command when you've command tagged mode off.
1999-03-26 00:33:13 +00:00
* Ensure that we don't believe tagged queuing is enabled yet.
* It turns out that sometimes the ISP just ignores our
* attempts to set parameters for devices that it hasn't
* seen yet.
*/
various fixes
2000-08-27 23:38:44 +00:00
sdp->isp_devparam[tgt].cur_dflags = sdf & ~DPARM_TQING;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
for (lun = 0; lun < (int) isp->isp_maxluns; lun++) {
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
mbs.param[0] = MBOX_SET_DEV_QUEUE_PARAMS;
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
mbs.param[1] = (channel << 15) | (tgt << 8) | lun;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
mbs.param[2] = sdp->isp_max_queue_depth;
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
mbs.param[3] = sdp->isp_devparam[tgt].exc_throttle;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGALL);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
if (mbs.param[0] != MBOX_COMMAND_COMPLETE) {
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
}
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
}
various fixes
2000-08-27 23:38:44 +00:00
for (tgt = 0; tgt < MAX_TARGETS; tgt++) {
if (sdp->isp_devparam[tgt].dev_refresh) {
isp->isp_sendmarker |= (1 << channel);
isp->isp_update |= (1 << channel);
break;
}
}
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
/*
* Fibre Channel specific initialization.
*
* Locks are held before coming here.
*/
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
static void
isp_fibre_init(isp)
struct ispsoftc *isp;
{
fcparam *fcp;
isp_icb_t *icbp;
mbreg_t mbs;
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
int loopid;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
fcp = isp->isp_param;
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
loopid = DEFAULT_LOOPID(isp);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
icbp = (isp_icb_t *) fcp->isp_scratch;
Add some prototype deadchip detection. Set FIFO bursting (1XX0 only- it's already on for the 2XX0) and detect the broken 1040A FIFO. Change bzero to MEMZERO (portability with **nux). Use memcpy for same reason. Finally detect QUEUE FULL conditions and return this as an error that will get cam_periph_error to do it's 'tagged openings now XXX' dance.
1999-01-10 02:55:10 +00:00
MEMZERO(icbp, sizeof (*icbp));
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
icbp->icb_version = ICB_VERSION1;
various fixes
2000-08-27 23:38:44 +00:00
/*
* Firmware Options are either retrieved from NVRAM or
* are patched elsewhere. We check them for sanity here
* and make changes based on board revision, but otherwise
* let others decide policy.
*/
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
/*
* If this is a 2100 < revision 5, we have to turn off FAIRNESS.
*/
if ((isp->isp_type == ISP_HA_FC_2100) && isp->isp_revision < 5) {
fcp->isp_fwoptions &= ~ICBOPT_FAIRNESS;
}
various fixes
2000-08-27 23:38:44 +00:00
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
/*
More code cleanup. Go back to using FULL_LOGIN Fibre Chan if f/w is less than 1.17.0 level. Change where we do the loop database init. Add in the CMD_RQLATER return. Add some register debounce.
1999-08-16 19:59:55 +00:00
* We have to use FULL LOGIN even though it resets the loop too much
* because otherwise port database entries don't get updated after
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
* a LIP- this is a known f/w bug for 2100 f/w less than 1.17.0.
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
*/
More code cleanup. Go back to using FULL_LOGIN Fibre Chan if f/w is less than 1.17.0 level. Change where we do the loop database init. Add in the CMD_RQLATER return. Add some register debounce.
1999-08-16 19:59:55 +00:00
if (ISP_FW_REVX(isp->isp_fwrev) < ISP_FW_REV(1, 17, 0)) {
fcp->isp_fwoptions |= ICBOPT_FULL_LOGIN;
}
various fixes
2000-08-27 23:38:44 +00:00
/*
* Insist on Port Database Update Async notifications
*/
fcp->isp_fwoptions |= ICBOPT_PDBCHANGE_AE;
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
/*
* We don't set ICBOPT_PORTNAME because we want our
* Node Name && Port Names to be distinct.
*/
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
icbp->icb_fwoptions = fcp->isp_fwoptions;
icbp->icb_maxfrmlen = fcp->isp_maxfrmlen;
if (icbp->icb_maxfrmlen < ICB_MIN_FRMLEN ||
icbp->icb_maxfrmlen > ICB_MAX_FRMLEN) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR,
"bad frame length (%d) from NVRAM- using %d",
fcp->isp_maxfrmlen, ICB_DFLT_FRMLEN);
Make firmware revision a triple. Clean up some FC init stuff for board versions with no BIOS. Separate mailbox interrupts from IOCB interrupts. Read OUTMAILBOX5 while RISC_INT is active- not after you clear it (potential race condition). Clear out older broken BIG_ENDIAN goop. Don't negotiate narrow/async for LVD busses at startup if already in LVD mode. Note usage of presumptive 1040C revision. For all the LIP, PDB Changed, Loop UP/DOWN async events, mark fw state as unknown as well as marking the need to do a getpdb on targets- after a LIP for certain the f/w has to do PRLI/PLOGI for all targets again and marking f/w state as unknown gives us a fighting chance to (start to) hold up for that to complete.
1999-04-04 02:28:29 +00:00
icbp->icb_maxfrmlen = ICB_DFLT_FRMLEN;
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
}
icbp->icb_maxalloc = fcp->isp_maxalloc;
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
if (icbp->icb_maxalloc < 1) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR,
"bad maximum allocation (%d)- using 16", fcp->isp_maxalloc);
Make firmware revision a triple. Clean up some FC init stuff for board versions with no BIOS. Separate mailbox interrupts from IOCB interrupts. Read OUTMAILBOX5 while RISC_INT is active- not after you clear it (potential race condition). Clear out older broken BIG_ENDIAN goop. Don't negotiate narrow/async for LVD busses at startup if already in LVD mode. Note usage of presumptive 1040C revision. For all the LIP, PDB Changed, Loop UP/DOWN async events, mark fw state as unknown as well as marking the need to do a getpdb on targets- after a LIP for certain the f/w has to do PRLI/PLOGI for all targets again and marking f/w state as unknown gives us a fighting chance to (start to) hold up for that to complete.
1999-04-04 02:28:29 +00:00
icbp->icb_maxalloc = 16;
}
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
icbp->icb_execthrottle = fcp->isp_execthrottle;
Make firmware revision a triple. Clean up some FC init stuff for board versions with no BIOS. Separate mailbox interrupts from IOCB interrupts. Read OUTMAILBOX5 while RISC_INT is active- not after you clear it (potential race condition). Clear out older broken BIG_ENDIAN goop. Don't negotiate narrow/async for LVD busses at startup if already in LVD mode. Note usage of presumptive 1040C revision. For all the LIP, PDB Changed, Loop UP/DOWN async events, mark fw state as unknown as well as marking the need to do a getpdb on targets- after a LIP for certain the f/w has to do PRLI/PLOGI for all targets again and marking f/w state as unknown gives us a fighting chance to (start to) hold up for that to complete.
1999-04-04 02:28:29 +00:00
if (icbp->icb_execthrottle < 1) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR,
"bad execution throttle of %d- using 16",
fcp->isp_execthrottle);
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
icbp->icb_execthrottle = ICB_DFLT_THROTTLE;
Make firmware revision a triple. Clean up some FC init stuff for board versions with no BIOS. Separate mailbox interrupts from IOCB interrupts. Read OUTMAILBOX5 while RISC_INT is active- not after you clear it (potential race condition). Clear out older broken BIG_ENDIAN goop. Don't negotiate narrow/async for LVD busses at startup if already in LVD mode. Note usage of presumptive 1040C revision. For all the LIP, PDB Changed, Loop UP/DOWN async events, mark fw state as unknown as well as marking the need to do a getpdb on targets- after a LIP for certain the f/w has to do PRLI/PLOGI for all targets again and marking f/w state as unknown gives us a fighting chance to (start to) hold up for that to complete.
1999-04-04 02:28:29 +00:00
}
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
icbp->icb_retry_delay = fcp->isp_retry_delay;
icbp->icb_retry_count = fcp->isp_retry_count;
oops on last
1998-12-05 01:46:40 +00:00
icbp->icb_hardaddr = loopid;
various fixes
2000-08-27 23:38:44 +00:00
/*
* Right now we just set extended options to prefer point-to-point
* over loop based upon some soft config options.
*/
Restructure nvram reading routine to split out to separate functions for 1020/1X80/12160/2X00- for readability. Add in 12160 (Ultra3) support- but not with PPR just yet. Fix and clarify fetching of return parameter for getting firmware rev which for the 2200 contains the connection topology (Private Loop (NL-port), N-port, FL-port, F-port). Synthesize the connection topology for the 2100 which can only be Private Loop or FL-port. Handle a couple of new async mailbox commands which signify connection in Point-to-Point mode (N-port or F-port) or indicate various toe stubbing getting to same. Approved: jkh@freebsd.org
2000-02-11 19:31:32 +00:00
if (IS_2200(isp)) {
icbp->icb_fwoptions |= ICBOPT_EXTENDED;
/*
* Prefer or force Point-To-Point instead Loop?
*/
if (isp->isp_confopts & ISP_CFG_NPORT)
icbp->icb_xfwoptions = ICBXOPT_PTP_2_LOOP;
else
icbp->icb_xfwoptions = ICBXOPT_LOOP_2_PTP;
}
Raise default FCP logintime to 60 seconds. Move the position of where we could have seen the loop up at least once so it makes sense. Change some stuff in ispscsicmd so we don't get stuck there if the loop has never come up yet. Add in some target mode support code.
2000-01-03 23:52:41 +00:00
icbp->icb_logintime = 60; /* 60 second login timeout */
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
if (fcp->isp_nodewwn) {
MAKE_NODE_NAME_FROM_WWN(icbp->icb_nodename, fcp->isp_nodewwn);
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
MAKE_NODE_NAME_FROM_WWN(icbp->icb_portname, fcp->isp_portwwn);
Make firmware revision a triple. Clean up some FC init stuff for board versions with no BIOS. Separate mailbox interrupts from IOCB interrupts. Read OUTMAILBOX5 while RISC_INT is active- not after you clear it (potential race condition). Clear out older broken BIG_ENDIAN goop. Don't negotiate narrow/async for LVD busses at startup if already in LVD mode. Note usage of presumptive 1040C revision. For all the LIP, PDB Changed, Loop UP/DOWN async events, mark fw state as unknown as well as marking the need to do a getpdb on targets- after a LIP for certain the f/w has to do PRLI/PLOGI for all targets again and marking f/w state as unknown gives us a fighting chance to (start to) hold up for that to complete.
1999-04-04 02:28:29 +00:00
} else {
fcp->isp_fwoptions &= ~(ICBOPT_USE_PORTNAME|ICBOPT_FULL_LOGIN);
Remove the Target mode functions until they're in better shape. Implement some suggested compilation cleanups from Eklund. Wire down a hard loop id if we are not on a platform that has the ability to get to a PCI BIOS (it still will float to the ID it gets after a LIP but at least we can try). Clarify that the expanded lun is based upon SCCLUN defines (in f/w).
1998-12-05 01:33:57 +00:00
}
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
icbp->icb_rqstqlen = RQUEST_QUEUE_LEN(isp);
icbp->icb_rsltqlen = RESULT_QUEUE_LEN(isp);
Make firmware revision a triple. Clean up some FC init stuff for board versions with no BIOS. Separate mailbox interrupts from IOCB interrupts. Read OUTMAILBOX5 while RISC_INT is active- not after you clear it (potential race condition). Clear out older broken BIG_ENDIAN goop. Don't negotiate narrow/async for LVD busses at startup if already in LVD mode. Note usage of presumptive 1040C revision. For all the LIP, PDB Changed, Loop UP/DOWN async events, mark fw state as unknown as well as marking the need to do a getpdb on targets- after a LIP for certain the f/w has to do PRLI/PLOGI for all targets again and marking f/w state as unknown gives us a fighting chance to (start to) hold up for that to complete.
1999-04-04 02:28:29 +00:00
icbp->icb_rqstaddr[RQRSP_ADDR0015] = DMA_LSW(isp->isp_rquest_dma);
icbp->icb_rqstaddr[RQRSP_ADDR1631] = DMA_MSW(isp->isp_rquest_dma);
icbp->icb_respaddr[RQRSP_ADDR0015] = DMA_LSW(isp->isp_result_dma);
icbp->icb_respaddr[RQRSP_ADDR1631] = DMA_MSW(isp->isp_result_dma);
various fixes
2000-08-27 23:38:44 +00:00
isp_prt(isp, ISP_LOGDEBUG1,
"isp_fibre_init: fwoptions 0x%x", fcp->isp_fwoptions);
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
ISP_SWIZZLE_ICB(isp, icbp);
More code cleanup. Go back to using FULL_LOGIN Fibre Chan if f/w is less than 1.17.0 level. Change where we do the loop database init. Add in the CMD_RQLATER return. Add some register debounce.
1999-08-16 19:59:55 +00:00
/*
* Do this *before* initializing the firmware.
*/
isp_mark_getpdb_all(isp);
fcp->isp_fwstate = FW_CONFIG_WAIT;
fcp->isp_loopstate = LOOP_NIL;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
mbs.param[0] = MBOX_INIT_FIRMWARE;
mbs.param[1] = 0;
mbs.param[2] = DMA_MSW(fcp->isp_scdma);
mbs.param[3] = DMA_LSW(fcp->isp_scdma);
mbs.param[4] = 0;
mbs.param[5] = 0;
mbs.param[6] = 0;
mbs.param[7] = 0;
isp_mboxcmd(isp, &mbs, MBLOGALL);
if (mbs.param[0] != MBOX_COMMAND_COMPLETE) {
return;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
isp->isp_reqidx = isp->isp_reqodx = 0;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
isp->isp_residx = 0;
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
isp->isp_sendmarker = 1;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
/*
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
* Whatever happens, we're now committed to being here.
*/
isp->isp_state = ISP_INITSTATE;
}
/*
* Fibre Channel Support- get the port database for the id.
*
* Locks are held before coming here. Return 0 if success,
* else failure.
*/
static void
isp_mark_getpdb_all(isp)
struct ispsoftc *isp;
{
fcparam *fcp = (fcparam *) isp->isp_param;
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
int i;
for (i = 0; i < MAX_FC_TARG; i++) {
fcp->portdb[i].valid = 0;
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
}
}
static int
isp_getpdb(isp, id, pdbp)
struct ispsoftc *isp;
int id;
isp_pdb_t *pdbp;
{
fcparam *fcp = (fcparam *) isp->isp_param;
mbreg_t mbs;
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
mbs.param[0] = MBOX_GET_PORT_DB;
mbs.param[1] = id << 8;
Make firmware revision a triple. Clean up some FC init stuff for board versions with no BIOS. Separate mailbox interrupts from IOCB interrupts. Read OUTMAILBOX5 while RISC_INT is active- not after you clear it (potential race condition). Clear out older broken BIG_ENDIAN goop. Don't negotiate narrow/async for LVD busses at startup if already in LVD mode. Note usage of presumptive 1040C revision. For all the LIP, PDB Changed, Loop UP/DOWN async events, mark fw state as unknown as well as marking the need to do a getpdb on targets- after a LIP for certain the f/w has to do PRLI/PLOGI for all targets again and marking f/w state as unknown gives us a fighting chance to (start to) hold up for that to complete.
1999-04-04 02:28:29 +00:00
mbs.param[2] = DMA_MSW(fcp->isp_scdma);
mbs.param[3] = DMA_LSW(fcp->isp_scdma);
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
/*
* Unneeded. For the 2100, except for initializing f/w, registers
* 4/5 have to not be written to.
* mbs.param[4] = 0;
* mbs.param[5] = 0;
*
*/
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
mbs.param[6] = 0;
mbs.param[7] = 0;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGALL & ~MBOX_COMMAND_PARAM_ERROR);
if (mbs.param[0] == MBOX_COMMAND_COMPLETE) {
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
ISP_UNSWIZZLE_AND_COPY_PDBP(isp, pdbp, fcp->isp_scratch);
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
return (0);
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
}
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
return (-1);
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
}
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
static u_int64_t
isp_get_portname(isp, loopid, nodename)
struct ispsoftc *isp;
int loopid;
int nodename;
{
u_int64_t wwn = 0;
mbreg_t mbs;
mbs.param[0] = MBOX_GET_PORT_NAME;
mbs.param[1] = loopid << 8;
if (nodename)
mbs.param[1] |= 1;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGALL & ~MBOX_COMMAND_PARAM_ERROR);
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
if (mbs.param[0] == MBOX_COMMAND_COMPLETE) {
wwn =
(((u_int64_t)(mbs.param[2] & 0xff)) << 56) |
(((u_int64_t)(mbs.param[2] >> 8)) << 48) |
(((u_int64_t)(mbs.param[3] & 0xff)) << 40) |
(((u_int64_t)(mbs.param[3] >> 8)) << 32) |
(((u_int64_t)(mbs.param[6] & 0xff)) << 24) |
(((u_int64_t)(mbs.param[6] >> 8)) << 16) |
(((u_int64_t)(mbs.param[7] & 0xff)) << 8) |
(((u_int64_t)(mbs.param[7] >> 8)));
}
return (wwn);
}
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
/*
* Make sure we have good FC link and know our Loop ID.
*/
static int
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_fclink_test(isp, usdelay)
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
struct ispsoftc *isp;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
int usdelay;
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
{
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
static char *toponames[] = {
"Private Loop",
"FL Port",
"N-Port to N-Port",
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
"F Port",
"F Port (no FLOGI_ACC response)"
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
};
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
mbreg_t mbs;
Pick up topology more sanely at f/w startup. Change the restrictions of where we can have targets (based on topology). Much more importantly, make sure all mods to isp_sendmarker or |= so we don't lose the marking of a bus that needs to have a marker sent for it.
2000-04-21 02:04:34 +00:00
int count;
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
u_int8_t lwfs;
fcparam *fcp;
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
#if defined(ISP2100_FABRIC)
isp_pdb_t pdb;
#endif
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
fcp = isp->isp_param;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
/*
* XXX: Here is where we would start a 'loop dead' timeout
*/
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
/*
* Wait up to N microseconds for F/W to go to a ready state.
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
*/
lwfs = FW_CONFIG_WAIT;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
count = 0;
while (count < usdelay) {
u_int64_t enano;
u_int32_t wrk;
NANOTIME_T hra, hrb;
GET_NANOTIME(&hra);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
isp_fw_state(isp);
if (lwfs != fcp->isp_fwstate) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGINFO, "Firmware State <%s->%s>",
isp2100_fw_statename((int)lwfs),
Remove the Target mode functions until they're in better shape. Implement some suggested compilation cleanups from Eklund. Wire down a hard loop id if we are not on a platform that has the ability to get to a PCI BIOS (it still will float to the ID it gets after a LIP but at least we can try). Clarify that the expanded lun is based upon SCCLUN defines (in f/w).
1998-12-05 01:33:57 +00:00
isp2100_fw_statename((int)fcp->isp_fwstate));
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
lwfs = fcp->isp_fwstate;
}
if (fcp->isp_fwstate == FW_READY) {
break;
}
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
GET_NANOTIME(&hrb);
/*
* Get the elapsed time in nanoseconds.
* Always guaranteed to be non-zero.
*/
enano = NANOTIME_SUB(&hrb, &hra);
/*
* If the elapsed time is less than 1 millisecond,
* delay a period of time up to that millisecond of
* waiting.
*/
isp_prt(isp, ISP_LOGDEBUG3, "usec%d: 0x%lx->0x%lx enano %u",
various fixes
2000-08-27 23:38:44 +00:00
count, (long) GET_NANOSEC(&hra), (long) GET_NANOSEC(&hrb),
enano);
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
/*
* This peculiar code is an attempt to try and avoid
* invoking u_int64_t math support functions for some
* platforms where linkage is a problem.
*/
if (enano < (1000 * 1000)) {
count += 1000;
enano = (1000 * 1000) - enano;
while (enano > (u_int64_t) 4000000000U) {
USEC_DELAY(4000000);
enano -= (u_int64_t) 4000000000U;
}
wrk = enano;
USEC_DELAY(wrk/1000);
} else {
while (enano > (u_int64_t) 4000000000U) {
count += 4000000;
enano -= (u_int64_t) 4000000000U;
}
wrk = enano;
count += (wrk / 1000);
}
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
/*
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
* If we haven't gone to 'ready' state, return.
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
*/
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
if (fcp->isp_fwstate != FW_READY) {
return (-1);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
/*
* Get our Loop ID (if possible). We really need to have it.
*/
mbs.param[0] = MBOX_GET_LOOP_ID;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGALL);
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
if (mbs.param[0] != MBOX_COMMAND_COMPLETE) {
return (-1);
}
fcp->isp_loopid = mbs.param[1];
Restructure nvram reading routine to split out to separate functions for 1020/1X80/12160/2X00- for readability. Add in 12160 (Ultra3) support- but not with PPR just yet. Fix and clarify fetching of return parameter for getting firmware rev which for the 2200 contains the connection topology (Private Loop (NL-port), N-port, FL-port, F-port). Synthesize the connection topology for the 2100 which can only be Private Loop or FL-port. Handle a couple of new async mailbox commands which signify connection in Point-to-Point mode (N-port or F-port) or indicate various toe stubbing getting to same. Approved: jkh@freebsd.org
2000-02-11 19:31:32 +00:00
if (IS_2200(isp)) {
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
int topo = (int) mbs.param[6];
if (topo < TOPO_NL_PORT || topo > TOPO_PTP_STUB)
topo = TOPO_PTP_STUB;
fcp->isp_topo = topo;
Restructure nvram reading routine to split out to separate functions for 1020/1X80/12160/2X00- for readability. Add in 12160 (Ultra3) support- but not with PPR just yet. Fix and clarify fetching of return parameter for getting firmware rev which for the 2200 contains the connection topology (Private Loop (NL-port), N-port, FL-port, F-port). Synthesize the connection topology for the 2100 which can only be Private Loop or FL-port. Handle a couple of new async mailbox commands which signify connection in Point-to-Point mode (N-port or F-port) or indicate various toe stubbing getting to same. Approved: jkh@freebsd.org
2000-02-11 19:31:32 +00:00
} else {
Pick up topology more sanely at f/w startup. Change the restrictions of where we can have targets (based on topology). Much more importantly, make sure all mods to isp_sendmarker or |= so we don't lose the marking of a bus that needs to have a marker sent for it.
2000-04-21 02:04:34 +00:00
fcp->isp_topo = TOPO_NL_PORT;
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
}
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
fcp->isp_alpa = mbs.param[2];
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
#if defined(ISP2100_FABRIC)
More code cleanup. Go back to using FULL_LOGIN Fibre Chan if f/w is less than 1.17.0 level. Change where we do the loop database init. Add in the CMD_RQLATER return. Add some register debounce.
1999-08-16 19:59:55 +00:00
fcp->isp_onfabric = 0;
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
if (fcp->isp_topo != TOPO_N_PORT &&
isp_getpdb(isp, FL_PORT_ID, &pdb) == 0) {
struct lportdb *lp;
if (IS_2100(isp)) {
Pick up topology more sanely at f/w startup. Change the restrictions of where we can have targets (based on topology). Much more importantly, make sure all mods to isp_sendmarker or |= so we don't lose the marking of a bus that needs to have a marker sent for it.
2000-04-21 02:04:34 +00:00
fcp->isp_topo = TOPO_FL_PORT;
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
}
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
fcp->isp_portid = mbs.param[2] | (((int)mbs.param[3]) << 16);
fcp->isp_onfabric = 1;
/*
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
* Save the Fabric controller's port database entry.
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
*/
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
lp = &fcp->portdb[FL_PORT_ID];
lp->node_wwn =
(((u_int64_t)pdb.pdb_nodename[0]) << 56) |
(((u_int64_t)pdb.pdb_nodename[1]) << 48) |
(((u_int64_t)pdb.pdb_nodename[2]) << 40) |
(((u_int64_t)pdb.pdb_nodename[3]) << 32) |
(((u_int64_t)pdb.pdb_nodename[4]) << 24) |
(((u_int64_t)pdb.pdb_nodename[5]) << 16) |
(((u_int64_t)pdb.pdb_nodename[6]) << 8) |
(((u_int64_t)pdb.pdb_nodename[7]));
lp->port_wwn =
(((u_int64_t)pdb.pdb_portname[0]) << 56) |
(((u_int64_t)pdb.pdb_portname[1]) << 48) |
(((u_int64_t)pdb.pdb_portname[2]) << 40) |
(((u_int64_t)pdb.pdb_portname[3]) << 32) |
(((u_int64_t)pdb.pdb_portname[4]) << 24) |
(((u_int64_t)pdb.pdb_portname[5]) << 16) |
(((u_int64_t)pdb.pdb_portname[6]) << 8) |
(((u_int64_t)pdb.pdb_portname[7]));
lp->roles =
(pdb.pdb_prli_svc3 & SVC3_ROLE_MASK) >> SVC3_ROLE_SHIFT;
lp->portid = BITS2WORD(pdb.pdb_portid_bits);
lp->loopid = pdb.pdb_loopid;
lp->loggedin = lp->valid = 1;
#if 0
if (isp->isp_rfabric == 0) {
isp_i_register_fc4_type(isp);
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
}
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
#endif
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
} else
#endif
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
{
fcp->isp_portid = mbs.param[2];
fcp->isp_onfabric = 0;
#if 0
isp->isp_rfabric = 0;
#endif
fcp->portdb[FL_PORT_ID].valid = 0;
}
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGINFO, topology, fcp->isp_loopid, fcp->isp_alpa,
fcp->isp_portid, fcp->isp_loopstate, toponames[fcp->isp_topo]);
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
return (0);
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
}
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
static char *
isp2100_fw_statename(state)
int state;
{
switch(state) {
case FW_CONFIG_WAIT: return "Config Wait";
case FW_WAIT_AL_PA: return "Waiting for AL_PA";
case FW_WAIT_LOGIN: return "Wait Login";
case FW_READY: return "Ready";
case FW_LOSS_OF_SYNC: return "Loss Of Sync";
case FW_ERROR: return "Error";
case FW_REINIT: return "Re-Init";
case FW_NON_PART: return "Nonparticipating";
default: return "?????";
}
}
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
static int
isp_same_lportdb(a, b)
struct lportdb *a, *b;
{
/*
* We decide two lports are the same if they have non-zero and
* identical port WWNs and identical loop IDs.
*/
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
if (a->port_wwn == 0 || a->port_wwn != b->port_wwn ||
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
a->loopid != b->loopid || a->roles != b->roles) {
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
return (0);
} else {
return (1);
}
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
/*
* Synchronize our soft copy of the port database with what the f/w thinks
* (with a view toward possibly for a specific target....)
*/
static int
isp_pdb_sync(isp, target)
struct ispsoftc *isp;
int target;
{
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
struct lportdb *lp, *tport;
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
fcparam *fcp = isp->isp_param;
isp_pdb_t pdb;
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
int loopid, prange, lim;
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
#ifdef ISP2100_FABRIC
/*
* XXX: If we do this *after* building up our local port database,
* XXX: the commands simply don't work.
*/
/*
* (Re)discover all fabric devices
*/
if (fcp->isp_onfabric)
(void) isp_scan_fabric(isp);
#endif
More code cleanup. Go back to using FULL_LOGIN Fibre Chan if f/w is less than 1.17.0 level. Change where we do the loop database init. Add in the CMD_RQLATER return. Add some register debounce.
1999-08-16 19:59:55 +00:00
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
switch (fcp->isp_topo) {
case TOPO_F_PORT:
case TOPO_PTP_STUB:
prange = 0;
break;
case TOPO_N_PORT:
prange = 2;
break;
default:
prange = FL_PORT_ID;
break;
}
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
/*
* Run through the local loop ports and get port database info
* for each loop ID.
*
* There's a somewhat unexplained situation where the f/w passes back
* the wrong database entity- if that happens, just restart (up to
* FL_PORT_ID times).
*/
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
tport = fcp->tport;
Raise default FCP logintime to 60 seconds. Move the position of where we could have seen the loop up at least once so it makes sense. Change some stuff in ispscsicmd so we don't get stuck there if the loop has never come up yet. Add in some target mode support code.
2000-01-03 23:52:41 +00:00
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
/*
* make sure the temp port database is clean...
*/
More code cleanup. Go back to using FULL_LOGIN Fibre Chan if f/w is less than 1.17.0 level. Change where we do the loop database init. Add in the CMD_RQLATER return. Add some register debounce.
1999-08-16 19:59:55 +00:00
MEMZERO((void *) tport, sizeof (tport));
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
for (lim = loopid = 0; loopid < prange; loopid++) {
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
lp = &tport[loopid];
lp->node_wwn = isp_get_portname(isp, loopid, 1);
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
if (fcp->isp_loopstate < LOOP_PDB_RCVD)
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
return (-1);
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
if (lp->node_wwn == 0)
continue;
lp->port_wwn = isp_get_portname(isp, loopid, 0);
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
if (fcp->isp_loopstate < LOOP_PDB_RCVD)
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
return (-1);
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
if (lp->port_wwn == 0) {
lp->node_wwn = 0;
continue;
}
More code cleanup. Go back to using FULL_LOGIN Fibre Chan if f/w is less than 1.17.0 level. Change where we do the loop database init. Add in the CMD_RQLATER return. Add some register debounce.
1999-08-16 19:59:55 +00:00
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
/*
* Get an entry....
*/
if (isp_getpdb(isp, loopid, &pdb) != 0) {
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
if (fcp->isp_loopstate < LOOP_PDB_RCVD)
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
return (-1);
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
continue;
}
More code cleanup. Go back to using FULL_LOGIN Fibre Chan if f/w is less than 1.17.0 level. Change where we do the loop database init. Add in the CMD_RQLATER return. Add some register debounce.
1999-08-16 19:59:55 +00:00
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
if (fcp->isp_loopstate < LOOP_PDB_RCVD)
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
return (-1);
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
/*
* If the returned database element doesn't match what we
* asked for, restart the process entirely (up to a point...).
*/
if (pdb.pdb_loopid != loopid) {
loopid = 0;
if (lim++ < FL_PORT_ID) {
continue;
}
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGWARN,
"giving up on synchronizing the port database");
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
return (-1);
}
More code cleanup. Go back to using FULL_LOGIN Fibre Chan if f/w is less than 1.17.0 level. Change where we do the loop database init. Add in the CMD_RQLATER return. Add some register debounce.
1999-08-16 19:59:55 +00:00
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
/*
* Save the pertinent info locally.
*/
lp->node_wwn =
(((u_int64_t)pdb.pdb_nodename[0]) << 56) |
(((u_int64_t)pdb.pdb_nodename[1]) << 48) |
(((u_int64_t)pdb.pdb_nodename[2]) << 40) |
(((u_int64_t)pdb.pdb_nodename[3]) << 32) |
(((u_int64_t)pdb.pdb_nodename[4]) << 24) |
(((u_int64_t)pdb.pdb_nodename[5]) << 16) |
(((u_int64_t)pdb.pdb_nodename[6]) << 8) |
(((u_int64_t)pdb.pdb_nodename[7]));
lp->port_wwn =
(((u_int64_t)pdb.pdb_portname[0]) << 56) |
(((u_int64_t)pdb.pdb_portname[1]) << 48) |
(((u_int64_t)pdb.pdb_portname[2]) << 40) |
(((u_int64_t)pdb.pdb_portname[3]) << 32) |
(((u_int64_t)pdb.pdb_portname[4]) << 24) |
(((u_int64_t)pdb.pdb_portname[5]) << 16) |
(((u_int64_t)pdb.pdb_portname[6]) << 8) |
(((u_int64_t)pdb.pdb_portname[7]));
lp->roles =
(pdb.pdb_prli_svc3 & SVC3_ROLE_MASK) >> SVC3_ROLE_SHIFT;
lp->portid = BITS2WORD(pdb.pdb_portid_bits);
lp->loopid = pdb.pdb_loopid;
/*
* Do a quick check to see whether this matches the saved port
* database for the same loopid. We do this here to save
* searching later (if possible). Note that this fails over
* time as things shuffle on the loop- we get the current
* loop state (where loop id as an index matches loop id in
* use) and then compare it to our saved database which
* never shifts.
*/
Raise default FCP logintime to 60 seconds. Move the position of where we could have seen the loop up at least once so it makes sense. Change some stuff in ispscsicmd so we don't get stuck there if the loop has never come up yet. Add in some target mode support code.
2000-01-03 23:52:41 +00:00
if (target >= 0 && isp_same_lportdb(lp, &fcp->portdb[target])) {
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
lp->valid = 1;
}
}
/*
* If we get this far, we've settled our differences with the f/w
* and we can say that the loop state is ready.
*/
fcp->isp_loopstate = LOOP_READY;
More code cleanup. Go back to using FULL_LOGIN Fibre Chan if f/w is less than 1.17.0 level. Change where we do the loop database init. Add in the CMD_RQLATER return. Add some register debounce.
1999-08-16 19:59:55 +00:00
/*
* Mark all of the permanent local loop database entries as invalid.
*/
for (loopid = 0; loopid < FL_PORT_ID; loopid++) {
fcp->portdb[loopid].valid = 0;
}
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
/*
* Now merge our local copy of the port database into our saved copy.
* Notify the outer layers of new devices arriving.
*/
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
for (loopid = 0; loopid < prange; loopid++) {
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
int i;
/*
* If we don't have a non-zero Port WWN, we're not here.
*/
if (tport[loopid].port_wwn == 0) {
continue;
}
/*
* If we've already marked our tmp copy as valid,
* this means that we've decided that it's the
More code cleanup. Go back to using FULL_LOGIN Fibre Chan if f/w is less than 1.17.0 level. Change where we do the loop database init. Add in the CMD_RQLATER return. Add some register debounce.
1999-08-16 19:59:55 +00:00
* same as our saved data base. This didn't include
* the 'valid' marking so we have set that here.
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
*/
if (tport[loopid].valid) {
fcp->portdb[loopid].valid = 1;
continue;
}
/*
* For the purposes of deciding whether this is the
* 'same' device or not, we only search for an identical
* Port WWN. Node WWNs may or may not be the same as
* the Port WWN, and there may be multiple different
* Port WWNs with the same Node WWN. It would be chaos
* to have multiple identical Port WWNs, so we don't
* allow that.
*/
for (i = 0; i < FL_PORT_ID; i++) {
int j;
if (fcp->portdb[i].port_wwn == 0)
continue;
if (fcp->portdb[i].port_wwn != tport[loopid].port_wwn)
continue;
/*
* We found this WWN elsewhere- it's changed
* loopids then. We don't change it's actual
* position in our cached port database- we
* just change the actual loop ID we'd use.
*/
if (fcp->portdb[i].loopid != loopid) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGINFO, portshift, i,
fcp->portdb[i].loopid,
More code cleanup. Go back to using FULL_LOGIN Fibre Chan if f/w is less than 1.17.0 level. Change where we do the loop database init. Add in the CMD_RQLATER return. Add some register debounce.
1999-08-16 19:59:55 +00:00
fcp->portdb[i].portid, loopid,
tport[loopid].portid);
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
}
More code cleanup. Go back to using FULL_LOGIN Fibre Chan if f/w is less than 1.17.0 level. Change where we do the loop database init. Add in the CMD_RQLATER return. Add some register debounce.
1999-08-16 19:59:55 +00:00
fcp->portdb[i].portid = tport[loopid].portid;
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
fcp->portdb[i].loopid = loopid;
fcp->portdb[i].valid = 1;
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
fcp->portdb[i].roles = tport[loopid].roles;
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
/*
* Now make sure this Port WWN doesn't exist elsewhere
* in the port database.
*/
for (j = i+1; j < FL_PORT_ID; j++) {
if (fcp->portdb[i].port_wwn !=
fcp->portdb[j].port_wwn) {
continue;
}
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGWARN, portdup, j, i);
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
/*
* Invalidate the 'old' *and* 'new' ones.
* This is really harsh and not quite right,
* but if this happens, we really don't know
* who is what at this point.
*/
fcp->portdb[i].valid = 0;
fcp->portdb[j].valid = 0;
}
break;
}
/*
* If we didn't traverse the entire port database,
* then we found (and remapped) an existing entry.
* No need to notify anyone- go for the next one.
*/
if (i < FL_PORT_ID) {
continue;
}
/*
* We've not found this Port WWN anywhere. It's a new entry.
* See if we can leave it where it is (with target == loopid).
*/
if (fcp->portdb[loopid].port_wwn != 0) {
for (lim = 0; lim < FL_PORT_ID; lim++) {
if (fcp->portdb[lim].port_wwn == 0)
break;
}
/* "Cannot Happen" */
if (lim == FL_PORT_ID) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGWARN, "Remap Overflow");
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
continue;
}
i = lim;
} else {
i = loopid;
}
/*
* NB: The actual loopid we use here is loopid- we may
* in fact be at a completely different index (target).
*/
fcp->portdb[i].loopid = loopid;
fcp->portdb[i].port_wwn = tport[loopid].port_wwn;
fcp->portdb[i].node_wwn = tport[loopid].node_wwn;
fcp->portdb[i].roles = tport[loopid].roles;
fcp->portdb[i].portid = tport[loopid].portid;
fcp->portdb[i].valid = 1;
/*
* Tell the outside world we've arrived.
*/
(void) isp_async(isp, ISPASYNC_PDB_CHANGED, &i);
}
/*
* Now find all previously used targets that are now invalid and
* notify the outer layers that they're gone.
*/
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
for (lp = fcp->portdb; lp < &fcp->portdb[prange]; lp++) {
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
if (lp->valid || lp->port_wwn == 0)
continue;
/*
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
* Tell the outside world we've gone away.
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
*/
loopid = lp - fcp->portdb;
(void) isp_async(isp, ISPASYNC_PDB_CHANGED, &loopid);
MEMZERO((void *) lp, sizeof (*lp));
}
#ifdef ISP2100_FABRIC
/*
* Now log in any fabric devices
*/
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
for (lp = &fcp->portdb[FC_SNS_ID+1];
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
lp < &fcp->portdb[MAX_FC_TARG]; lp++) {
Slightly cleaner fabric support (whiter whites! redder reds!).. No, seriously- only attempt to logout a previously logged in fabric device. Fix a longstanding bug for aborting overtime commands- handle halves have always been reversed. Clean up some error messages to indicate channel number. Approved:jkh
2000-02-29 05:52:14 +00:00
u_int32_t portid;
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
mbreg_t mbs;
/*
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
* Anything here?
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
*/
if (lp->port_wwn == 0)
continue;
Slightly cleaner fabric support (whiter whites! redder reds!).. No, seriously- only attempt to logout a previously logged in fabric device. Fix a longstanding bug for aborting overtime commands- handle halves have always been reversed. Clean up some error messages to indicate channel number. Approved:jkh
2000-02-29 05:52:14 +00:00
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
/*
* Don't try to log into yourself.
*/
Slightly cleaner fabric support (whiter whites! redder reds!).. No, seriously- only attempt to logout a previously logged in fabric device. Fix a longstanding bug for aborting overtime commands- handle halves have always been reversed. Clean up some error messages to indicate channel number. Approved:jkh
2000-02-29 05:52:14 +00:00
if ((portid = lp->portid) == fcp->isp_portid)
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
continue;
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
/*
* If we'd been logged in- see if we still are and we haven't
* changed. If so, no need to log ourselves out, etc..
*/
if (lp->loggedin &&
isp_getpdb(isp, lp->loopid, &pdb) == 0) {
int nrole;
u_int64_t nwwnn, nwwpn;
nwwnn =
(((u_int64_t)pdb.pdb_nodename[0]) << 56) |
(((u_int64_t)pdb.pdb_nodename[1]) << 48) |
(((u_int64_t)pdb.pdb_nodename[2]) << 40) |
(((u_int64_t)pdb.pdb_nodename[3]) << 32) |
(((u_int64_t)pdb.pdb_nodename[4]) << 24) |
(((u_int64_t)pdb.pdb_nodename[5]) << 16) |
(((u_int64_t)pdb.pdb_nodename[6]) << 8) |
(((u_int64_t)pdb.pdb_nodename[7]));
nwwpn =
(((u_int64_t)pdb.pdb_portname[0]) << 56) |
(((u_int64_t)pdb.pdb_portname[1]) << 48) |
(((u_int64_t)pdb.pdb_portname[2]) << 40) |
(((u_int64_t)pdb.pdb_portname[3]) << 32) |
(((u_int64_t)pdb.pdb_portname[4]) << 24) |
(((u_int64_t)pdb.pdb_portname[5]) << 16) |
(((u_int64_t)pdb.pdb_portname[6]) << 8) |
(((u_int64_t)pdb.pdb_portname[7]));
nrole = (pdb.pdb_prli_svc3 & SVC3_ROLE_MASK) >>
SVC3_ROLE_SHIFT;
if (pdb.pdb_loopid == lp->loopid && lp->portid ==
(u_int32_t) BITS2WORD(pdb.pdb_portid_bits) &&
nwwnn == lp->node_wwn && nwwpn == lp->port_wwn &&
lp->roles == nrole) {
lp->loggedin = lp->valid = 1;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGINFO, lretained,
(int) (lp - fcp->portdb),
(int) lp->loopid, lp->portid);
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
continue;
}
}
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
/*
Slightly cleaner fabric support (whiter whites! redder reds!).. No, seriously- only attempt to logout a previously logged in fabric device. Fix a longstanding bug for aborting overtime commands- handle halves have always been reversed. Clean up some error messages to indicate channel number. Approved:jkh
2000-02-29 05:52:14 +00:00
* Force a logout if we were logged in.
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
*/
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
if (lp->loggedin) {
Slightly cleaner fabric support (whiter whites! redder reds!).. No, seriously- only attempt to logout a previously logged in fabric device. Fix a longstanding bug for aborting overtime commands- handle halves have always been reversed. Clean up some error messages to indicate channel number. Approved:jkh
2000-02-29 05:52:14 +00:00
mbs.param[0] = MBOX_FABRIC_LOGOUT;
mbs.param[1] = lp->loopid << 8;
mbs.param[2] = 0;
mbs.param[3] = 0;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGNONE);
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
lp->loggedin = 0;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGINFO, plogout,
(int) (lp - fcp->portdb), lp->loopid, lp->portid);
Slightly cleaner fabric support (whiter whites! redder reds!).. No, seriously- only attempt to logout a previously logged in fabric device. Fix a longstanding bug for aborting overtime commands- handle halves have always been reversed. Clean up some error messages to indicate channel number. Approved:jkh
2000-02-29 05:52:14 +00:00
}
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
/*
* And log in....
*/
Slightly cleaner fabric support (whiter whites! redder reds!).. No, seriously- only attempt to logout a previously logged in fabric device. Fix a longstanding bug for aborting overtime commands- handle halves have always been reversed. Clean up some error messages to indicate channel number. Approved:jkh
2000-02-29 05:52:14 +00:00
loopid = lp - fcp->portdb;
lp->loopid = 0;
do {
mbs.param[0] = MBOX_FABRIC_LOGIN;
mbs.param[1] = loopid << 8;
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
mbs.param[2] = portid >> 16;
mbs.param[3] = portid & 0xffff;
Slightly cleaner fabric support (whiter whites! redder reds!).. No, seriously- only attempt to logout a previously logged in fabric device. Fix a longstanding bug for aborting overtime commands- handle halves have always been reversed. Clean up some error messages to indicate channel number. Approved:jkh
2000-02-29 05:52:14 +00:00
if (IS_2200(isp)) {
/* only issue a PLOGI if not logged in */
mbs.param[1] |= 0x1;
}
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGALL & ~(MBOX_LOOP_ID_USED |
MBOX_PORT_ID_USED | MBOX_COMMAND_ERROR));
Slightly cleaner fabric support (whiter whites! redder reds!).. No, seriously- only attempt to logout a previously logged in fabric device. Fix a longstanding bug for aborting overtime commands- handle halves have always been reversed. Clean up some error messages to indicate channel number. Approved:jkh
2000-02-29 05:52:14 +00:00
switch (mbs.param[0]) {
case MBOX_LOOP_ID_USED:
/*
* Try the next available loop id.
*/
loopid++;
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
break;
Slightly cleaner fabric support (whiter whites! redder reds!).. No, seriously- only attempt to logout a previously logged in fabric device. Fix a longstanding bug for aborting overtime commands- handle halves have always been reversed. Clean up some error messages to indicate channel number. Approved:jkh
2000-02-29 05:52:14 +00:00
case MBOX_PORT_ID_USED:
/*
* This port is already logged in.
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
* Snaffle the loop id it's using if it's
* nonzero, otherwise we're hosed.
Slightly cleaner fabric support (whiter whites! redder reds!).. No, seriously- only attempt to logout a previously logged in fabric device. Fix a longstanding bug for aborting overtime commands- handle halves have always been reversed. Clean up some error messages to indicate channel number. Approved:jkh
2000-02-29 05:52:14 +00:00
*/
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
if (mbs.param[1] != 0) {
loopid = mbs.param[1];
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGINFO, retained,
loopid, (int) (lp - fcp->portdb),
lp->portid);
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
} else {
loopid = MAX_FC_TARG;
break;
Slightly cleaner fabric support (whiter whites! redder reds!).. No, seriously- only attempt to logout a previously logged in fabric device. Fix a longstanding bug for aborting overtime commands- handle halves have always been reversed. Clean up some error messages to indicate channel number. Approved:jkh
2000-02-29 05:52:14 +00:00
}
/* FALLTHROUGH */
case MBOX_COMMAND_COMPLETE:
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
lp->loggedin = 1;
Slightly cleaner fabric support (whiter whites! redder reds!).. No, seriously- only attempt to logout a previously logged in fabric device. Fix a longstanding bug for aborting overtime commands- handle halves have always been reversed. Clean up some error messages to indicate channel number. Approved:jkh
2000-02-29 05:52:14 +00:00
lp->loopid = loopid;
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
break;
Slightly cleaner fabric support (whiter whites! redder reds!).. No, seriously- only attempt to logout a previously logged in fabric device. Fix a longstanding bug for aborting overtime commands- handle halves have always been reversed. Clean up some error messages to indicate channel number. Approved:jkh
2000-02-29 05:52:14 +00:00
case MBOX_COMMAND_ERROR:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGINFO, plogierr,
portid, mbs.param[1]);
Slightly cleaner fabric support (whiter whites! redder reds!).. No, seriously- only attempt to logout a previously logged in fabric device. Fix a longstanding bug for aborting overtime commands- handle halves have always been reversed. Clean up some error messages to indicate channel number. Approved:jkh
2000-02-29 05:52:14 +00:00
/* FALLTHROUGH */
case MBOX_ALL_IDS_USED: /* We're outta IDs */
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
default:
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
loopid = MAX_FC_TARG;
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
break;
More code cleanup. Go back to using FULL_LOGIN Fibre Chan if f/w is less than 1.17.0 level. Change where we do the loop database init. Add in the CMD_RQLATER return. Add some register debounce.
1999-08-16 19:59:55 +00:00
}
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
} while (lp->loopid == 0 && loopid < MAX_FC_TARG);
/*
* If we get here and we haven't set a Loop ID,
* we failed to log into this device.
*/
if (lp->loopid == 0) {
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
continue;
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
}
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
/*
* Make sure we can get the approriate port information.
*/
Slightly cleaner fabric support (whiter whites! redder reds!).. No, seriously- only attempt to logout a previously logged in fabric device. Fix a longstanding bug for aborting overtime commands- handle halves have always been reversed. Clean up some error messages to indicate channel number. Approved:jkh
2000-02-29 05:52:14 +00:00
if (isp_getpdb(isp, lp->loopid, &pdb) != 0) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGWARN, nopdb, lp->portid);
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
goto dump_em;
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
}
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
if (pdb.pdb_loopid != lp->loopid) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGWARN, pdbmfail1,
lp->portid, pdb.pdb_loopid);
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
goto dump_em;
}
if (lp->portid != (u_int32_t) BITS2WORD(pdb.pdb_portid_bits)) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGWARN, pdbmfail2,
lp->portid, BITS2WORD(pdb.pdb_portid_bits));
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
goto dump_em;
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
}
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
lp->roles =
(pdb.pdb_prli_svc3 & SVC3_ROLE_MASK) >> SVC3_ROLE_SHIFT;
lp->node_wwn =
(((u_int64_t)pdb.pdb_nodename[0]) << 56) |
(((u_int64_t)pdb.pdb_nodename[1]) << 48) |
(((u_int64_t)pdb.pdb_nodename[2]) << 40) |
(((u_int64_t)pdb.pdb_nodename[3]) << 32) |
(((u_int64_t)pdb.pdb_nodename[4]) << 24) |
(((u_int64_t)pdb.pdb_nodename[5]) << 16) |
(((u_int64_t)pdb.pdb_nodename[6]) << 8) |
(((u_int64_t)pdb.pdb_nodename[7]));
lp->port_wwn =
(((u_int64_t)pdb.pdb_portname[0]) << 56) |
(((u_int64_t)pdb.pdb_portname[1]) << 48) |
(((u_int64_t)pdb.pdb_portname[2]) << 40) |
(((u_int64_t)pdb.pdb_portname[3]) << 32) |
(((u_int64_t)pdb.pdb_portname[4]) << 24) |
(((u_int64_t)pdb.pdb_portname[5]) << 16) |
(((u_int64_t)pdb.pdb_portname[6]) << 8) |
(((u_int64_t)pdb.pdb_portname[7]));
/*
* Check to make sure this all makes sense.
*/
if (lp->node_wwn && lp->port_wwn) {
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
lp->valid = 1;
Slightly cleaner fabric support (whiter whites! redder reds!).. No, seriously- only attempt to logout a previously logged in fabric device. Fix a longstanding bug for aborting overtime commands- handle halves have always been reversed. Clean up some error messages to indicate channel number. Approved:jkh
2000-02-29 05:52:14 +00:00
loopid = lp - fcp->portdb;
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
(void) isp_async(isp, ISPASYNC_PDB_CHANGED, &loopid);
continue;
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
}
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
dump_em:
lp->valid = 0;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGINFO,
ldumped, loopid, lp->loopid, lp->portid);
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
mbs.param[0] = MBOX_FABRIC_LOGOUT;
mbs.param[1] = lp->loopid << 8;
mbs.param[2] = 0;
mbs.param[3] = 0;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGNONE);
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
}
#endif
Raise default FCP logintime to 60 seconds. Move the position of where we could have seen the loop up at least once so it makes sense. Change some stuff in ispscsicmd so we don't get stuck there if the loop has never come up yet. Add in some target mode support code.
2000-01-03 23:52:41 +00:00
/*
* If we get here, we've for sure seen not only a valid loop
* but know what is or isn't on it, so mark this for usage
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
* in isp_start.
Raise default FCP logintime to 60 seconds. Move the position of where we could have seen the loop up at least once so it makes sense. Change some stuff in ispscsicmd so we don't get stuck there if the loop has never come up yet. Add in some target mode support code.
2000-01-03 23:52:41 +00:00
*/
fcp->loop_seen_once = 1;
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
return (0);
}
#ifdef ISP2100_FABRIC
static int
isp_scan_fabric(isp)
struct ispsoftc *isp;
{
fcparam *fcp = isp->isp_param;
u_int32_t portid, first_nz_portid;
sns_screq_t *reqp;
sns_scrsp_t *resp;
mbreg_t mbs;
int hicap;
reqp = (sns_screq_t *) fcp->isp_scratch;
resp = (sns_scrsp_t *) (&((char *)fcp->isp_scratch)[0x100]);
first_nz_portid = portid = fcp->isp_portid;
for (hicap = 0; hicap < 1024; hicap++) {
MEMZERO((void *) reqp, SNS_GAN_REQ_SIZE);
reqp->snscb_rblen = SNS_GAN_RESP_SIZE >> 1;
reqp->snscb_addr[RQRSP_ADDR0015] =
DMA_LSW(fcp->isp_scdma + 0x100);
reqp->snscb_addr[RQRSP_ADDR1631] =
DMA_MSW(fcp->isp_scdma + 0x100);
reqp->snscb_sblen = 6;
reqp->snscb_data[0] = SNS_GAN;
reqp->snscb_data[4] = portid & 0xffff;
reqp->snscb_data[5] = (portid >> 16) & 0xff;
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
ISP_SWIZZLE_SNS_REQ(isp, reqp);
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
mbs.param[0] = MBOX_SEND_SNS;
mbs.param[1] = SNS_GAN_REQ_SIZE >> 1;
mbs.param[2] = DMA_MSW(fcp->isp_scdma);
mbs.param[3] = DMA_LSW(fcp->isp_scdma);
mbs.param[6] = 0;
mbs.param[7] = 0;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGALL);
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
if (mbs.param[0] != MBOX_COMMAND_COMPLETE) {
return (-1);
}
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
ISP_UNSWIZZLE_SNS_RSP(isp, resp, SNS_GAN_RESP_SIZE >> 1);
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
portid = (((u_int32_t) resp->snscb_port_id[0]) << 16) |
(((u_int32_t) resp->snscb_port_id[1]) << 8) |
(((u_int32_t) resp->snscb_port_id[2]));
if (isp_async(isp, ISPASYNC_FABRIC_DEV, resp)) {
return (-1);
}
if (first_nz_portid == 0 && portid) {
first_nz_portid = portid;
}
if (first_nz_portid == portid) {
return (0);
}
}
/*
* We either have a broken name server or a huge fabric if we get here.
*/
return (0);
}
#endif
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
/*
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
* Start a command. Locking is assumed done in the caller.
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
*/
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
int
isp_start(xs)
XS_T *xs;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
{
struct ispsoftc *isp;
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
u_int16_t iptr, optr;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
union {
ispreq_t *_reqp;
ispreqt2_t *_t2reqp;
} _u;
#define reqp _u._reqp
#define t2reqp _u._t2reqp
#define UZSIZE max(sizeof (ispreq_t), sizeof (ispreqt2_t))
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
int target, i;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
XS_INITERR(xs);
isp = XS_ISP(xs);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
if (isp->isp_state != ISP_RUNSTATE) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR, "Adapter not at RUNSTATE");
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
XS_SETERR(xs, HBA_BOTCH);
return (CMD_COMPLETE);
}
/*
Clean out residual bogosity for fast posting stuff- ISP_NO_FASTPOST_SCSI is gone as a define. We just don't support fast posting for anything less than the 1240/1080/1280/12160 or Fibre Channel cards. Put in support for CDB's larger than 12 bytes for parallel SCSI (up to 44 bytes are allowed). Approved: jkh
2000-02-15 00:35:00 +00:00
* Check command CDB length, etc.. We really are limited to 16 bytes
* for Fibre Channel, but can do up to 44 bytes in parallel SCSI,
* but probably only if we're running fairly new firmware (we'll
* let the old f/w choke on an extended command queue entry).
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
*/
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
Clean out residual bogosity for fast posting stuff- ISP_NO_FASTPOST_SCSI is gone as a define. We just don't support fast posting for anything less than the 1240/1080/1280/12160 or Fibre Channel cards. Put in support for CDB's larger than 12 bytes for parallel SCSI (up to 44 bytes are allowed). Approved: jkh
2000-02-15 00:35:00 +00:00
if (XS_CDBLEN(xs) > (IS_FC(isp)? 16 : 44) || XS_CDBLEN(xs) == 0) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR,
"unsupported cdb length (%d, CDB[0]=0x%x)",
XS_CDBLEN(xs), XS_CDBP(xs)[0] & 0xff);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
XS_SETERR(xs, HBA_BOTCH);
return (CMD_COMPLETE);
}
/*
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
* Check to see whether we have good firmware state still or
* need to refresh our port database for this target.
*/
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
target = XS_TGT(xs);
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
if (IS_FC(isp)) {
fcparam *fcp = isp->isp_param;
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
struct lportdb *lp;
#if defined(ISP2100_FABRIC)
Pick up topology more sanely at f/w startup. Change the restrictions of where we can have targets (based on topology). Much more importantly, make sure all mods to isp_sendmarker or |= so we don't lose the marking of a bus that needs to have a marker sent for it.
2000-04-21 02:04:34 +00:00
/*
* If we're not on a Fabric, we can't have a target
* above FL_PORT_ID-1. If we're on a fabric and
* connected as an F-port, we can't have a target
* less than FC_SNS_ID+1.
*/
if (fcp->isp_onfabric == 0) {
if (target >= FL_PORT_ID) {
XS_SETERR(xs, HBA_SELTIMEOUT);
return (CMD_COMPLETE);
}
} else {
if (target >= FL_PORT_ID && target <= FC_SNS_ID) {
XS_SETERR(xs, HBA_SELTIMEOUT);
return (CMD_COMPLETE);
}
if (fcp->isp_topo == TOPO_F_PORT &&
target < FL_PORT_ID) {
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
XS_SETERR(xs, HBA_SELTIMEOUT);
return (CMD_COMPLETE);
}
}
#endif
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
/*
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
* Check for f/w being in ready state. If the f/w
* isn't in ready state, then we don't know our
* loop ID and the f/w hasn't completed logging
* into all targets on the loop. If this is the
* case, then bounce the command. We pretend this is
* a SELECTION TIMEOUT error if we've never gone to
* FW_READY state at all- in this case we may not
* be hooked to a loop at all and we shouldn't hang
* the machine for this. Otherwise, defer this command
* until later.
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
*/
if (fcp->isp_fwstate != FW_READY) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
/*
* Give ourselves at most a 250ms delay.
*/
if (isp_fclink_test(isp, 250000)) {
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
XS_SETERR(xs, HBA_SELTIMEOUT);
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
if (fcp->loop_seen_once) {
More code cleanup. Go back to using FULL_LOGIN Fibre Chan if f/w is less than 1.17.0 level. Change where we do the loop database init. Add in the CMD_RQLATER return. Add some register debounce.
1999-08-16 19:59:55 +00:00
return (CMD_RQLATER);
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
} else {
return (CMD_COMPLETE);
}
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
}
}
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
/*
* If our loop state is such that we haven't yet received
* a "Port Database Changed" notification (after a LIP or
* a Loop Reset or firmware initialization), then defer
Raise default FCP logintime to 60 seconds. Move the position of where we could have seen the loop up at least once so it makes sense. Change some stuff in ispscsicmd so we don't get stuck there if the loop has never come up yet. Add in some target mode support code.
2000-01-03 23:52:41 +00:00
* sending commands for a little while, but only if we've
* seen a valid loop at one point (otherwise we can get
* stuck at initialization time).
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
*/
if (fcp->isp_loopstate < LOOP_PDB_RCVD) {
XS_SETERR(xs, HBA_SELTIMEOUT);
Raise default FCP logintime to 60 seconds. Move the position of where we could have seen the loop up at least once so it makes sense. Change some stuff in ispscsicmd so we don't get stuck there if the loop has never come up yet. Add in some target mode support code.
2000-01-03 23:52:41 +00:00
if (fcp->loop_seen_once) {
return (CMD_RQLATER);
} else {
return (CMD_COMPLETE);
}
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
}
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
/*
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
* If our loop state is now such that we've just now
* received a Port Database Change notification, then
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
* we have to go off and (re)synchronize our port
* database.
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
*/
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
if (fcp->isp_loopstate == LOOP_PDB_RCVD) {
if (isp_pdb_sync(isp, target)) {
XS_SETERR(xs, HBA_SELTIMEOUT);
return (CMD_COMPLETE);
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
}
}
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
/*
* XXX: Here's were we would cancel any loop_dead flag
* XXX: also cancel in dead_loop timeout that's running
*/
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
/*
* Now check whether we should even think about pursuing this.
*/
lp = &fcp->portdb[target];
if (lp->valid == 0) {
XS_SETERR(xs, HBA_SELTIMEOUT);
return (CMD_COMPLETE);
}
if ((lp->roles & (SVC3_TGT_ROLE >> SVC3_ROLE_SHIFT)) == 0) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGDEBUG2,
"Target %d does not have target service", target);
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
XS_SETERR(xs, HBA_SELTIMEOUT);
return (CMD_COMPLETE);
}
/*
* Now turn target into what the actual loop ID is.
*/
target = lp->loopid;
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
}
/*
* Next check to see if any HBA or Device
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
* parameters need to be updated.
*/
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
if (isp->isp_update != 0) {
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
isp_update(isp);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
if (isp_getrqentry(isp, &iptr, &optr, (void **) &reqp)) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGDEBUG0, "Request Queue Overflow");
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
XS_SETERR(xs, HBA_BOTCH);
return (CMD_EAGAIN);
}
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
/*
* Now see if we need to synchronize the ISP with respect to anything.
* We do dual duty here (cough) for synchronizing for busses other
* than which we got here to send a command to.
*/
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
if (isp->isp_sendmarker) {
Add Dual LVD bus (1280) support
1999-12-16 05:42:02 +00:00
u_int8_t n = (IS_DUALBUS(isp)? 2: 1);
ISP_DMASETUP now returns a value to be possibly punted to outer layers. Turn request queue overflow messages into debug messages. Ensure on isp_restarts that we nullify the xflist array.
1998-09-17 21:03:45 +00:00
/*
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
* Check ports to send markers for...
ISP_DMASETUP now returns a value to be possibly punted to outer layers. Turn request queue overflow messages into debug messages. Ensure on isp_restarts that we nullify the xflist array.
1998-09-17 21:03:45 +00:00
*/
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
for (i = 0; i < n; i++) {
if ((isp->isp_sendmarker & (1 << i)) == 0) {
continue;
}
MEMZERO((void *) reqp, sizeof (*reqp));
reqp->req_header.rqs_entry_count = 1;
reqp->req_header.rqs_entry_type = RQSTYPE_MARKER;
reqp->req_modifier = SYNC_ALL;
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
reqp->req_target = i << 7; /* insert bus number */
ISP_SWIZZLE_REQUEST(isp, reqp);
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
ISP_ADD_REQUEST(isp, iptr);
ISP_DMASETUP now returns a value to be possibly punted to outer layers. Turn request queue overflow messages into debug messages. Ensure on isp_restarts that we nullify the xflist array.
1998-09-17 21:03:45 +00:00
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
if (isp_getrqentry(isp, &iptr, &optr, (void **)&reqp)) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGDEBUG0,
"Request Queue Overflow+");
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
XS_SETERR(xs, HBA_BOTCH);
return (CMD_EAGAIN);
}
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
}
Add some prototype deadchip detection. Set FIFO bursting (1XX0 only- it's already on for the 2XX0) and detect the broken 1040A FIFO. Change bzero to MEMZERO (portability with **nux). Use memcpy for same reason. Finally detect QUEUE FULL conditions and return this as an error that will get cam_periph_error to do it's 'tagged openings now XXX' dance.
1999-01-10 02:55:10 +00:00
MEMZERO((void *) reqp, UZSIZE);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
reqp->req_header.rqs_entry_count = 1;
More code cleanup. Go back to using FULL_LOGIN Fibre Chan if f/w is less than 1.17.0 level. Change where we do the loop database init. Add in the CMD_RQLATER return. Add some register debounce.
1999-08-16 19:59:55 +00:00
if (IS_FC(isp)) {
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
reqp->req_header.rqs_entry_type = RQSTYPE_T2RQS;
} else {
Clean out residual bogosity for fast posting stuff- ISP_NO_FASTPOST_SCSI is gone as a define. We just don't support fast posting for anything less than the 1240/1080/1280/12160 or Fibre Channel cards. Put in support for CDB's larger than 12 bytes for parallel SCSI (up to 44 bytes are allowed). Approved: jkh
2000-02-15 00:35:00 +00:00
if (XS_CDBLEN(xs) > 12)
reqp->req_header.rqs_entry_type = RQSTYPE_CMDONLY;
else
reqp->req_header.rqs_entry_type = RQSTYPE_REQUEST;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
reqp->req_header.rqs_flags = 0;
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
reqp->req_header.rqs_seqno = 0;
More code cleanup. Go back to using FULL_LOGIN Fibre Chan if f/w is less than 1.17.0 level. Change where we do the loop database init. Add in the CMD_RQLATER return. Add some register debounce.
1999-08-16 19:59:55 +00:00
if (IS_FC(isp)) {
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
/*
* See comment in isp_intr
*/
XS_RESID(xs) = 0;
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
/*
I was misinformed. I cannot get away from specifying tags for FC. Some devices are happy w/o them- some are unhappy (IBM drives).
1999-10-28 02:48:42 +00:00
* Fibre Channel always requires some kind of tag.
* The Qlogic drivers seem be happy not to use a tag,
* but this breaks for some devices (IBM drives).
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
*/
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
if (XS_TAG_P(xs)) {
t2reqp->req_flags = XS_TAG_TYPE(xs);
I was misinformed. I cannot get away from specifying tags for FC. Some devices are happy w/o them- some are unhappy (IBM drives).
1999-10-28 02:48:42 +00:00
} else {
various fixes
2000-08-27 23:38:44 +00:00
/*
* If we don't know what tag to use, use HEAD OF QUEUE
* for Request Sense or Ordered (for safety's sake).
*/
I was misinformed. I cannot get away from specifying tags for FC. Some devices are happy w/o them- some are unhappy (IBM drives).
1999-10-28 02:48:42 +00:00
if (XS_CDBP(xs)[0] == 0x3) /* REQUEST SENSE */
t2reqp->req_flags = REQFLAG_HTAG;
else
t2reqp->req_flags = REQFLAG_OTAG;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
} else {
sdparam *sdp = (sdparam *)isp->isp_param;
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
if ((sdp->isp_devparam[target].cur_dflags & DPARM_TQING) &&
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
XS_TAG_P(xs)) {
reqp->req_flags = XS_TAG_TYPE(xs);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
}
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
reqp->req_target = target | (XS_CHANNEL(xs) << 7);
More code cleanup. Go back to using FULL_LOGIN Fibre Chan if f/w is less than 1.17.0 level. Change where we do the loop database init. Add in the CMD_RQLATER return. Add some register debounce.
1999-08-16 19:59:55 +00:00
if (IS_SCSI(isp)) {
Remove the Target mode functions until they're in better shape. Implement some suggested compilation cleanups from Eklund. Wire down a hard loop id if we are not on a platform that has the ability to get to a PCI BIOS (it still will float to the ID it gets after a LIP but at least we can try). Clarify that the expanded lun is based upon SCCLUN defines (in f/w).
1998-12-05 01:33:57 +00:00
reqp->req_lun_trn = XS_LUN(xs);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
reqp->req_cdblen = XS_CDBLEN(xs);
Remove the Target mode functions until they're in better shape. Implement some suggested compilation cleanups from Eklund. Wire down a hard loop id if we are not on a platform that has the ability to get to a PCI BIOS (it still will float to the ID it gets after a LIP but at least we can try). Clarify that the expanded lun is based upon SCCLUN defines (in f/w).
1998-12-05 01:33:57 +00:00
} else {
Once we have firmware running (if isp_reset) and this is the first time through, establish what our LUN width is. Unfortunately, we can't ask the f/w. If we loaded the f/w, we'll now assume we have expanded LUNs (SCCLUN for fibre channel, just plain 32 LUN for SCSI). If we didn't load firmware, assume 8 LUNs for SCSI and 1 LUN for Fibre Channel. We have to assume only one LUN for Fibre Channel because the LUN setting in Request Queue entries is in different places whether we have SCCLUN firmware or not, so the only LUN guaranteed to work for both is LUN 0. Clean up the rest of isp.c so that ISP2100_SCCLUN defines aren't used- instead use run time determinants based upon isp->isp_maxluns. After starting firmware, delay 500us to give it a chance to get rolling. Fix the interrupt service routine to check for both isr && sema being zero before thinking this was a spurious interrupt. Following the manuals, allow for both Mailbox as well as Queue Reponse type interrupts for regular SCSI.
2000-06-18 04:56:17 +00:00
if (isp->isp_maxluns > 16)
t2reqp->req_scclun = XS_LUN(xs);
else
t2reqp->req_lun_trn = XS_LUN(xs);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
Suggested by bde@freebsd.org- memcpy not necessarily good to use. D'oh- not in the BSD DKI. Stop being lazy and finish the defines so MEMCPY becomes bzero for FreeBSD.
1999-01-10 11:15:23 +00:00
MEMCPY(reqp->req_cdb, XS_CDBP(xs), XS_CDBLEN(xs));
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
reqp->req_time = XS_TIME(xs) / 1000;
if (reqp->req_time == 0 && XS_TIME(xs))
reqp->req_time = 1;
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
/*
* Always give a bit more leeway to commands after a bus reset.
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
* XXX: DOES NOT DISTINGUISH WHICH PORT MAY HAVE BEEN SYNCED
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
*/
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
if (isp->isp_sendmarker && reqp->req_time < 5) {
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
reqp->req_time = 5;
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
}
if (isp_save_xs(isp, xs, &reqp->req_handle)) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGDEBUG1, "out of xflist pointers");
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
XS_SETERR(xs, HBA_BOTCH);
return (CMD_EAGAIN);
}
/*
* Set up DMA and/or do any bus swizzling of the request entry
* so that the Qlogic F/W understands what is being asked of it.
*/
ISP_DMASETUP now returns a value to be possibly punted to outer layers. Turn request queue overflow messages into debug messages. Ensure on isp_restarts that we nullify the xflist array.
1998-09-17 21:03:45 +00:00
i = ISP_DMASETUP(isp, xs, reqp, &iptr, optr);
if (i != CMD_QUEUED) {
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
isp_destroy_handle(isp, reqp->req_handle);
ISP_DMASETUP now returns a value to be possibly punted to outer layers. Turn request queue overflow messages into debug messages. Ensure on isp_restarts that we nullify the xflist array.
1998-09-17 21:03:45 +00:00
/*
* dmasetup sets actual error in packet, and
* return what we were given to return.
*/
return (i);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
XS_SETERR(xs, HBA_NOERROR);
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGDEBUG2,
"START cmd for %d.%d.%d cmd 0x%x datalen %d",
XS_CHANNEL(xs), target, XS_LUN(xs), XS_CDBP(xs)[0], XS_XFRLEN(xs));
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
ISP_ADD_REQUEST(isp, iptr);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
isp->isp_nactive++;
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
if (isp->isp_sendmarker)
isp->isp_sendmarker = 0;
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
return (CMD_QUEUED);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
#undef reqp
#undef t2reqp
}
/*
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
* isp control
* Locks (ints blocked) assumed held.
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
*/
int
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
isp_control(isp, ctl, arg)
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
struct ispsoftc *isp;
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
ispctl_t ctl;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
void *arg;
{
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
XS_T *xs;
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
mbreg_t mbs;
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
int bus, tgt;
u_int32_t handle;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
switch (ctl) {
default:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR, "Unknown Control Opcode 0x%x", ctl);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case ISPCTL_RESET_BUS:
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
/*
* Issue a bus reset.
*/
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
mbs.param[0] = MBOX_BUS_RESET;
Slightly cleaner fabric support (whiter whites! redder reds!).. No, seriously- only attempt to logout a previously logged in fabric device. Fix a longstanding bug for aborting overtime commands- handle halves have always been reversed. Clean up some error messages to indicate channel number. Approved:jkh
2000-02-29 05:52:14 +00:00
mbs.param[2] = 0;
More code cleanup. Go back to using FULL_LOGIN Fibre Chan if f/w is less than 1.17.0 level. Change where we do the loop database init. Add in the CMD_RQLATER return. Add some register debounce.
1999-08-16 19:59:55 +00:00
if (IS_SCSI(isp)) {
Roll internal release tag. Print out if we're in a 64 bit PCI slot. Use fast memory timing NVRAM parameter. Clean up and fix establishment of default target parameters. Don't use NVRAM if are flagged as not to do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC mode but disabled disconnect/reconnect and wide!!). Fix delays after resets. BUS resets not done in isp_init anymore- relegated to OS specific outer layers. Fix a buglet where you can get in a loop for a NULL xs in the completion list in isp_intr. Add in some defines that can disable fast posting. Add in code for Loop Up/Loop Down events that call into the outer layers as to what to do.
1999-02-09 01:07:06 +00:00
mbs.param[1] =
((sdparam *) isp->isp_param)->isp_bus_reset_delay;
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
if (mbs.param[1] < 2)
mbs.param[1] = 2;
More code cleanup. Go back to using FULL_LOGIN Fibre Chan if f/w is less than 1.17.0 level. Change where we do the loop database init. Add in the CMD_RQLATER return. Add some register debounce.
1999-08-16 19:59:55 +00:00
bus = *((int *) arg);
Slightly cleaner fabric support (whiter whites! redder reds!).. No, seriously- only attempt to logout a previously logged in fabric device. Fix a longstanding bug for aborting overtime commands- handle halves have always been reversed. Clean up some error messages to indicate channel number. Approved:jkh
2000-02-29 05:52:14 +00:00
if (IS_DUALBUS(isp))
mbs.param[2] = bus;
Roll internal release tag. Print out if we're in a 64 bit PCI slot. Use fast memory timing NVRAM parameter. Clean up and fix establishment of default target parameters. Don't use NVRAM if are flagged as not to do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC mode but disabled disconnect/reconnect and wide!!). Fix delays after resets. BUS resets not done in isp_init anymore- relegated to OS specific outer layers. Fix a buglet where you can get in a loop for a NULL xs in the completion list in isp_intr. Add in some defines that can disable fast posting. Add in code for Loop Up/Loop Down events that call into the outer layers as to what to do.
1999-02-09 01:07:06 +00:00
} else {
More code cleanup. Go back to using FULL_LOGIN Fibre Chan if f/w is less than 1.17.0 level. Change where we do the loop database init. Add in the CMD_RQLATER return. Add some register debounce.
1999-08-16 19:59:55 +00:00
mbs.param[1] = 10;
bus = 0;
Roll internal release tag. Print out if we're in a 64 bit PCI slot. Use fast memory timing NVRAM parameter. Clean up and fix establishment of default target parameters. Don't use NVRAM if are flagged as not to do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC mode but disabled disconnect/reconnect and wide!!). Fix delays after resets. BUS resets not done in isp_init anymore- relegated to OS specific outer layers. Fix a buglet where you can get in a loop for a NULL xs in the completion list in isp_intr. Add in some defines that can disable fast posting. Add in code for Loop Up/Loop Down events that call into the outer layers as to what to do.
1999-02-09 01:07:06 +00:00
}
Pick up topology more sanely at f/w startup. Change the restrictions of where we can have targets (based on topology). Much more importantly, make sure all mods to isp_sendmarker or |= so we don't lose the marking of a bus that needs to have a marker sent for it.
2000-04-21 02:04:34 +00:00
isp->isp_sendmarker |= (1 << bus);
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGALL);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
if (mbs.param[0] != MBOX_COMMAND_COMPLETE) {
break;
}
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGINFO,
"driver initiated bus reset of bus %d", bus);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
return (0);
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
case ISPCTL_RESET_DEV:
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
tgt = (*((int *) arg)) & 0xffff;
bus = (*((int *) arg)) >> 16;
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
mbs.param[0] = MBOX_ABORT_TARGET;
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
mbs.param[1] = (tgt << 8) | (bus << 15);
Roll internal release tag. Print out if we're in a 64 bit PCI slot. Use fast memory timing NVRAM parameter. Clean up and fix establishment of default target parameters. Don't use NVRAM if are flagged as not to do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC mode but disabled disconnect/reconnect and wide!!). Fix delays after resets. BUS resets not done in isp_init anymore- relegated to OS specific outer layers. Fix a buglet where you can get in a loop for a NULL xs in the completion list in isp_intr. Add in some defines that can disable fast posting. Add in code for Loop Up/Loop Down events that call into the outer layers as to what to do.
1999-02-09 01:07:06 +00:00
mbs.param[2] = 3; /* 'delay', in seconds */
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGALL);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
if (mbs.param[0] != MBOX_COMMAND_COMPLETE) {
break;
}
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGINFO,
"Target %d on Bus %d Reset Succeeded", tgt, bus);
Pick up topology more sanely at f/w startup. Change the restrictions of where we can have targets (based on topology). Much more importantly, make sure all mods to isp_sendmarker or |= so we don't lose the marking of a bus that needs to have a marker sent for it.
2000-04-21 02:04:34 +00:00
isp->isp_sendmarker |= (1 << bus);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
return (0);
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
case ISPCTL_ABORT_CMD:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
xs = (XS_T *) arg;
Clean up ISPCTL_ABORT_CMD function to not be too chatty if it succeeds, or even if it fails with INVALID_PARM (which just means that the handle doesn't refer to an active commane).
2000-07-05 06:41:36 +00:00
tgt = XS_TGT(xs);
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
handle = isp_find_handle(isp, xs);
if (handle == 0) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGWARN,
"cannot find handle for command to abort");
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
}
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
bus = XS_CHANNEL(xs);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
mbs.param[0] = MBOX_ABORT;
More code cleanup. Go back to using FULL_LOGIN Fibre Chan if f/w is less than 1.17.0 level. Change where we do the loop database init. Add in the CMD_RQLATER return. Add some register debounce.
1999-08-16 19:59:55 +00:00
if (IS_FC(isp)) {
Once we have firmware running (if isp_reset) and this is the first time through, establish what our LUN width is. Unfortunately, we can't ask the f/w. If we loaded the f/w, we'll now assume we have expanded LUNs (SCCLUN for fibre channel, just plain 32 LUN for SCSI). If we didn't load firmware, assume 8 LUNs for SCSI and 1 LUN for Fibre Channel. We have to assume only one LUN for Fibre Channel because the LUN setting in Request Queue entries is in different places whether we have SCCLUN firmware or not, so the only LUN guaranteed to work for both is LUN 0. Clean up the rest of isp.c so that ISP2100_SCCLUN defines aren't used- instead use run time determinants based upon isp->isp_maxluns. After starting firmware, delay 500us to give it a chance to get rolling. Fix the interrupt service routine to check for both isr && sema being zero before thinking this was a spurious interrupt. Following the manuals, allow for both Mailbox as well as Queue Reponse type interrupts for regular SCSI.
2000-06-18 04:56:17 +00:00
if (isp->isp_maxluns > 16) {
Clean up ISPCTL_ABORT_CMD function to not be too chatty if it succeeds, or even if it fails with INVALID_PARM (which just means that the handle doesn't refer to an active commane).
2000-07-05 06:41:36 +00:00
mbs.param[1] = tgt << 8;
Once we have firmware running (if isp_reset) and this is the first time through, establish what our LUN width is. Unfortunately, we can't ask the f/w. If we loaded the f/w, we'll now assume we have expanded LUNs (SCCLUN for fibre channel, just plain 32 LUN for SCSI). If we didn't load firmware, assume 8 LUNs for SCSI and 1 LUN for Fibre Channel. We have to assume only one LUN for Fibre Channel because the LUN setting in Request Queue entries is in different places whether we have SCCLUN firmware or not, so the only LUN guaranteed to work for both is LUN 0. Clean up the rest of isp.c so that ISP2100_SCCLUN defines aren't used- instead use run time determinants based upon isp->isp_maxluns. After starting firmware, delay 500us to give it a chance to get rolling. Fix the interrupt service routine to check for both isr && sema being zero before thinking this was a spurious interrupt. Following the manuals, allow for both Mailbox as well as Queue Reponse type interrupts for regular SCSI.
2000-06-18 04:56:17 +00:00
mbs.param[4] = 0;
mbs.param[5] = 0;
mbs.param[6] = XS_LUN(xs);
} else {
Clean up ISPCTL_ABORT_CMD function to not be too chatty if it succeeds, or even if it fails with INVALID_PARM (which just means that the handle doesn't refer to an active commane).
2000-07-05 06:41:36 +00:00
mbs.param[1] = tgt << 8 | XS_LUN(xs);
Once we have firmware running (if isp_reset) and this is the first time through, establish what our LUN width is. Unfortunately, we can't ask the f/w. If we loaded the f/w, we'll now assume we have expanded LUNs (SCCLUN for fibre channel, just plain 32 LUN for SCSI). If we didn't load firmware, assume 8 LUNs for SCSI and 1 LUN for Fibre Channel. We have to assume only one LUN for Fibre Channel because the LUN setting in Request Queue entries is in different places whether we have SCCLUN firmware or not, so the only LUN guaranteed to work for both is LUN 0. Clean up the rest of isp.c so that ISP2100_SCCLUN defines aren't used- instead use run time determinants based upon isp->isp_maxluns. After starting firmware, delay 500us to give it a chance to get rolling. Fix the interrupt service routine to check for both isr && sema being zero before thinking this was a spurious interrupt. Following the manuals, allow for both Mailbox as well as Queue Reponse type interrupts for regular SCSI.
2000-06-18 04:56:17 +00:00
}
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
} else {
mbs.param[1] =
(bus << 15) | (XS_TGT(xs) << 8) | XS_LUN(xs);
}
Slightly cleaner fabric support (whiter whites! redder reds!).. No, seriously- only attempt to logout a previously logged in fabric device. Fix a longstanding bug for aborting overtime commands- handle halves have always been reversed. Clean up some error messages to indicate channel number. Approved:jkh
2000-02-29 05:52:14 +00:00
mbs.param[3] = handle >> 16;
mbs.param[2] = handle & 0xffff;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGALL & ~MBOX_COMMAND_ERROR);
if (mbs.param[0] == MBOX_COMMAND_COMPLETE) {
return (0);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
}
various fixes
2000-08-27 23:38:44 +00:00
/*
* XXX: Look for command in the REQUEST QUEUE. That is,
* XXX: It hasen't been picked up by firmware yet.
*/
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
break;
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
case ISPCTL_UPDATE_PARAMS:
isp_update(isp);
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
return (0);
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
case ISPCTL_FCLINK_TEST:
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
if (IS_FC(isp)) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
int usdelay = (arg)? *((int *) arg) : 250000;
return (isp_fclink_test(isp, usdelay));
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
}
break;
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
Raise default FCP logintime to 60 seconds. Move the position of where we could have seen the loop up at least once so it makes sense. Change some stuff in ispscsicmd so we don't get stuck there if the loop has never come up yet. Add in some target mode support code.
2000-01-03 23:52:41 +00:00
case ISPCTL_PDB_SYNC:
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
if (IS_FC(isp)) {
return (isp_pdb_sync(isp, -1));
}
break;
Raise default FCP logintime to 60 seconds. Move the position of where we could have seen the loop up at least once so it makes sense. Change some stuff in ispscsicmd so we don't get stuck there if the loop has never come up yet. Add in some target mode support code.
2000-01-03 23:52:41 +00:00
#ifdef ISP_TARGET_MODE
case ISPCTL_TOGGLE_TMODE:
various fixes
2000-08-27 23:38:44 +00:00
{
int ena = *(int *)arg;
Raise default FCP logintime to 60 seconds. Move the position of where we could have seen the loop up at least once so it makes sense. Change some stuff in ispscsicmd so we don't get stuck there if the loop has never come up yet. Add in some target mode support code.
2000-01-03 23:52:41 +00:00
if (IS_SCSI(isp)) {
mbs.param[0] = MBOX_ENABLE_TARGET_MODE;
mbs.param[1] = (ena)? ENABLE_TARGET_FLAG : 0;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGALL);
Raise default FCP logintime to 60 seconds. Move the position of where we could have seen the loop up at least once so it makes sense. Change some stuff in ispscsicmd so we don't get stuck there if the loop has never come up yet. Add in some target mode support code.
2000-01-03 23:52:41 +00:00
if (mbs.param[0] != MBOX_COMMAND_COMPLETE) {
break;
}
various fixes
2000-08-27 23:38:44 +00:00
} else {
fcparam *fcp = isp->isp_param;
/*
* We assume somebody has quiesced this bus.
*/
if (ena) {
if (fcp->isp_fwoptions & ICBOPT_TGT_ENABLE) {
return (0);
}
fcp->isp_fwoptions |= ICBOPT_TGT_ENABLE;
} else {
if (!(fcp->isp_fwoptions & ICBOPT_TGT_ENABLE)) {
return (0);
}
fcp->isp_fwoptions &= ~ICBOPT_TGT_ENABLE;
}
isp->isp_state = ISP_NILSTATE;
isp_reset(isp);
if (isp->isp_state != ISP_RESETSTATE) {
break;
}
isp_init(isp);
if (isp->isp_state != ISP_INITSTATE) {
break;
}
isp->isp_state = ISP_RUNSTATE;
Raise default FCP logintime to 60 seconds. Move the position of where we could have seen the loop up at least once so it makes sense. Change some stuff in ispscsicmd so we don't get stuck there if the loop has never come up yet. Add in some target mode support code.
2000-01-03 23:52:41 +00:00
}
return (0);
various fixes
2000-08-27 23:38:44 +00:00
}
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
#endif
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
}
return (-1);
}
/*
* Interrupt Service Routine(s).
*
* External (OS) framework has done the appropriate locking,
* and the locking will be held throughout this function.
*/
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
/*
* Limit our stack depth by sticking with the max likely number
* of completions on a request queue at any one time.
*/
#define MAX_REQUESTQ_COMPLETIONS 32
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
int
isp_intr(arg)
void *arg;
{
struct ispsoftc *isp = arg;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
XS_T *complist[MAX_REQUESTQ_COMPLETIONS], *xs;
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
u_int16_t iptr, optr, isr, sema, junk;
Roll internal release tag. Print out if we're in a 64 bit PCI slot. Use fast memory timing NVRAM parameter. Clean up and fix establishment of default target parameters. Don't use NVRAM if are flagged as not to do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC mode but disabled disconnect/reconnect and wide!!). Fix delays after resets. BUS resets not done in isp_init anymore- relegated to OS specific outer layers. Fix a buglet where you can get in a loop for a NULL xs in the completion list in isp_intr. Add in some defines that can disable fast posting. Add in code for Loop Up/Loop Down events that call into the outer layers as to what to do.
1999-02-09 01:07:06 +00:00
int i, nlooked = 0, ndone = 0;
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
if (IS_2100(isp)) {
i = 0;
do {
isr = ISP_READ(isp, BIU_ISR);
junk = ISP_READ(isp, BIU_ISR);
} while (isr != junk && ++i < 1000);
if (isr != junk) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGWARN,
"isr unsteady (%x, %x)", isr, junk);
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
}
i = 0;
do {
sema = ISP_READ(isp, BIU_SEMA);
junk = ISP_READ(isp, BIU_SEMA);
} while (sema != junk && ++i < 1000);
if (sema != junk) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGWARN,
"sema unsteady (%x, %x)", sema, junk);
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
}
} else {
isr = ISP_READ(isp, BIU_ISR);
sema = ISP_READ(isp, BIU_SEMA);
}
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGDEBUG3, "isp_intr isr %x sem %x", isr, sema);
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
isr &= INT_PENDING_MASK(isp);
sema &= BIU_SEMA_LOCK;
Once we have firmware running (if isp_reset) and this is the first time through, establish what our LUN width is. Unfortunately, we can't ask the f/w. If we loaded the f/w, we'll now assume we have expanded LUNs (SCCLUN for fibre channel, just plain 32 LUN for SCSI). If we didn't load firmware, assume 8 LUNs for SCSI and 1 LUN for Fibre Channel. We have to assume only one LUN for Fibre Channel because the LUN setting in Request Queue entries is in different places whether we have SCCLUN firmware or not, so the only LUN guaranteed to work for both is LUN 0. Clean up the rest of isp.c so that ISP2100_SCCLUN defines aren't used- instead use run time determinants based upon isp->isp_maxluns. After starting firmware, delay 500us to give it a chance to get rolling. Fix the interrupt service routine to check for both isr && sema being zero before thinking this was a spurious interrupt. Following the manuals, allow for both Mailbox as well as Queue Reponse type interrupts for regular SCSI.
2000-06-18 04:56:17 +00:00
if (isr == 0 && sema == 0) {
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
return (0);
}
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
if (sema) {
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
u_int16_t mbox;
if (IS_2100(isp)) {
i = 0;
do {
mbox = ISP_READ(isp, OUTMAILBOX0);
junk = ISP_READ(isp, OUTMAILBOX0);;
} while (junk != mbox && ++i < 1000);
if (mbox != junk) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGWARN,
"mailbox0 unsteady (%x, %x)", mbox, junk);
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
ISP_WRITE(isp, BIU_SEMA, 0);
ISP_WRITE(isp, HCCR, HCCR_CMD_CLEAR_RISC_INT);
return (1);
}
} else {
mbox = ISP_READ(isp, OUTMAILBOX0);
}
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
if (mbox & 0x4000) {
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
int obits, i = 0;
if ((obits = isp->isp_mboxbsy) != 0) {
isp->isp_mboxtmp[i++] = mbox;
for (i = 1; i < 8; i++) {
if ((obits & (1 << i)) == 0) {
continue;
}
isp->isp_mboxtmp[i] =
ISP_READ(isp, MBOX_OFF(i));
}
Change delay loop in new isp_mboxcmd to the use of the new MBOX_WAIT_COMPLETE macro. Change notification of completion of a mailbox command in isp_intr to MBOX_NOTIFY_COMPLETE macro.
2000-07-04 01:02:38 +00:00
MBOX_NOTIFY_COMPLETE(isp);
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
} else {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGWARN,
"Mbox Command Async (0x%x) with no waiters",
mbox);
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
}
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
} else {
u_int32_t fhandle = isp_parse_async(isp, (int) mbox);
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGDEBUG2, "Async Mbox 0x%x", mbox);
Make firmware revision a triple. Clean up some FC init stuff for board versions with no BIOS. Separate mailbox interrupts from IOCB interrupts. Read OUTMAILBOX5 while RISC_INT is active- not after you clear it (potential race condition). Clear out older broken BIG_ENDIAN goop. Don't negotiate narrow/async for LVD busses at startup if already in LVD mode. Note usage of presumptive 1040C revision. For all the LIP, PDB Changed, Loop UP/DOWN async events, mark fw state as unknown as well as marking the need to do a getpdb on targets- after a LIP for certain the f/w has to do PRLI/PLOGI for all targets again and marking f/w state as unknown gives us a fighting chance to (start to) hold up for that to complete.
1999-04-04 02:28:29 +00:00
if (fhandle > 0) {
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
isp_fastpost_complete(isp, fhandle);
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
}
}
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
if (IS_FC(isp) || isp->isp_state != ISP_RUNSTATE) {
Once we have firmware running (if isp_reset) and this is the first time through, establish what our LUN width is. Unfortunately, we can't ask the f/w. If we loaded the f/w, we'll now assume we have expanded LUNs (SCCLUN for fibre channel, just plain 32 LUN for SCSI). If we didn't load firmware, assume 8 LUNs for SCSI and 1 LUN for Fibre Channel. We have to assume only one LUN for Fibre Channel because the LUN setting in Request Queue entries is in different places whether we have SCCLUN firmware or not, so the only LUN guaranteed to work for both is LUN 0. Clean up the rest of isp.c so that ISP2100_SCCLUN defines aren't used- instead use run time determinants based upon isp->isp_maxluns. After starting firmware, delay 500us to give it a chance to get rolling. Fix the interrupt service routine to check for both isr && sema being zero before thinking this was a spurious interrupt. Following the manuals, allow for both Mailbox as well as Queue Reponse type interrupts for regular SCSI.
2000-06-18 04:56:17 +00:00
ISP_WRITE(isp, BIU_SEMA, 0);
ISP_WRITE(isp, HCCR, HCCR_CMD_CLEAR_RISC_INT);
return (1);
}
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
/*
* We can't be getting this now.
*/
if (isp->isp_state != ISP_RUNSTATE) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGWARN,
"interrupt (isr=%x, sema=%x) when not ready", isr, sema);
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
ISP_WRITE(isp, INMAILBOX5, ISP_READ(isp, OUTMAILBOX5));
ISP_WRITE(isp, HCCR, HCCR_CMD_CLEAR_RISC_INT);
ISP_WRITE(isp, BIU_SEMA, 0);
return (1);
}
Make firmware revision a triple. Clean up some FC init stuff for board versions with no BIOS. Separate mailbox interrupts from IOCB interrupts. Read OUTMAILBOX5 while RISC_INT is active- not after you clear it (potential race condition). Clear out older broken BIG_ENDIAN goop. Don't negotiate narrow/async for LVD busses at startup if already in LVD mode. Note usage of presumptive 1040C revision. For all the LIP, PDB Changed, Loop UP/DOWN async events, mark fw state as unknown as well as marking the need to do a getpdb on targets- after a LIP for certain the f/w has to do PRLI/PLOGI for all targets again and marking f/w state as unknown gives us a fighting chance to (start to) hold up for that to complete.
1999-04-04 02:28:29 +00:00
/*
* You *must* read OUTMAILBOX5 prior to clearing the RISC interrupt.
*/
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
optr = isp->isp_residx;
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
if (IS_2100(isp)) {
i = 0;
do {
iptr = ISP_READ(isp, OUTMAILBOX5);
junk = ISP_READ(isp, OUTMAILBOX5);
} while (junk != iptr && ++i < 1000);
if (iptr != junk) {
ISP_WRITE(isp, HCCR, HCCR_CMD_CLEAR_RISC_INT);
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGWARN,
"mailbox5 unsteady (%x, %x)", iptr, junk);
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
return (1);
}
} else {
iptr = ISP_READ(isp, OUTMAILBOX5);
}
Once we have firmware running (if isp_reset) and this is the first time through, establish what our LUN width is. Unfortunately, we can't ask the f/w. If we loaded the f/w, we'll now assume we have expanded LUNs (SCCLUN for fibre channel, just plain 32 LUN for SCSI). If we didn't load firmware, assume 8 LUNs for SCSI and 1 LUN for Fibre Channel. We have to assume only one LUN for Fibre Channel because the LUN setting in Request Queue entries is in different places whether we have SCCLUN firmware or not, so the only LUN guaranteed to work for both is LUN 0. Clean up the rest of isp.c so that ISP2100_SCCLUN defines aren't used- instead use run time determinants based upon isp->isp_maxluns. After starting firmware, delay 500us to give it a chance to get rolling. Fix the interrupt service routine to check for both isr && sema being zero before thinking this was a spurious interrupt. Following the manuals, allow for both Mailbox as well as Queue Reponse type interrupts for regular SCSI.
2000-06-18 04:56:17 +00:00
if (sema) {
ISP_WRITE(isp, BIU_SEMA, 0);
}
Make firmware revision a triple. Clean up some FC init stuff for board versions with no BIOS. Separate mailbox interrupts from IOCB interrupts. Read OUTMAILBOX5 while RISC_INT is active- not after you clear it (potential race condition). Clear out older broken BIG_ENDIAN goop. Don't negotiate narrow/async for LVD busses at startup if already in LVD mode. Note usage of presumptive 1040C revision. For all the LIP, PDB Changed, Loop UP/DOWN async events, mark fw state as unknown as well as marking the need to do a getpdb on targets- after a LIP for certain the f/w has to do PRLI/PLOGI for all targets again and marking f/w state as unknown gives us a fighting chance to (start to) hold up for that to complete.
1999-04-04 02:28:29 +00:00
ISP_WRITE(isp, HCCR, HCCR_CMD_CLEAR_RISC_INT);
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
Once we have firmware running (if isp_reset) and this is the first time through, establish what our LUN width is. Unfortunately, we can't ask the f/w. If we loaded the f/w, we'll now assume we have expanded LUNs (SCCLUN for fibre channel, just plain 32 LUN for SCSI). If we didn't load firmware, assume 8 LUNs for SCSI and 1 LUN for Fibre Channel. We have to assume only one LUN for Fibre Channel because the LUN setting in Request Queue entries is in different places whether we have SCCLUN firmware or not, so the only LUN guaranteed to work for both is LUN 0. Clean up the rest of isp.c so that ISP2100_SCCLUN defines aren't used- instead use run time determinants based upon isp->isp_maxluns. After starting firmware, delay 500us to give it a chance to get rolling. Fix the interrupt service routine to check for both isr && sema being zero before thinking this was a spurious interrupt. Following the manuals, allow for both Mailbox as well as Queue Reponse type interrupts for regular SCSI.
2000-06-18 04:56:17 +00:00
if (optr == iptr && sema == 0) {
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
/*
* There are a lot of these- reasons unknown- mostly on
* faster Alpha machines.
*
* I tried delaying after writing HCCR_CMD_CLEAR_RISC_INT to
* make sure the old interrupt went away (to avoid 'ringing'
* effects), but that didn't stop this from occurring.
*/
junk = ISP_READ(isp, BIU_ISR);
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGDEBUG2,
"bogus intr- isr %x (%x) iptr %x optr %x",
isr, junk, iptr, optr);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
while (optr != iptr) {
ispstatusreq_t *sp;
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
u_int16_t oop;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
int buddaboom = 0;
sp = (ispstatusreq_t *) ISP_QUEUE_ENTRY(isp->isp_result, optr);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
oop = optr;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
optr = ISP_NXT_QENTRY(optr, RESULT_QUEUE_LEN(isp));
Roll internal release tag. Print out if we're in a 64 bit PCI slot. Use fast memory timing NVRAM parameter. Clean up and fix establishment of default target parameters. Don't use NVRAM if are flagged as not to do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC mode but disabled disconnect/reconnect and wide!!). Fix delays after resets. BUS resets not done in isp_init anymore- relegated to OS specific outer layers. Fix a buglet where you can get in a loop for a NULL xs in the completion list in isp_intr. Add in some defines that can disable fast posting. Add in code for Loop Up/Loop Down events that call into the outer layers as to what to do.
1999-02-09 01:07:06 +00:00
nlooked++;
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
/*
* Do any appropriate unswizzling of what the Qlogic f/w has
Raise default FCP logintime to 60 seconds. Move the position of where we could have seen the loop up at least once so it makes sense. Change some stuff in ispscsicmd so we don't get stuck there if the loop has never come up yet. Add in some target mode support code.
2000-01-03 23:52:41 +00:00
* written into memory so it makes sense to us. This is a
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
* per-platform thing. Also includes any memory barriers.
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
*/
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
ISP_UNSWIZZLE_RESPONSE(isp, sp, oop);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
if (sp->req_header.rqs_entry_type != RQSTYPE_RESPONSE) {
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
if (isp_handle_other_response(isp, sp, &optr) == 0) {
various fixes
2000-08-27 23:38:44 +00:00
MEMZERO(sp, sizeof (isphdr_t));
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
continue;
}
/*
* It really has to be a bounced request just copied
temp fix for internal queue overflow problem
1999-04-14 17:37:36 +00:00
* from the request queue to the response queue. If
* not, something bad has happened.
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
*/
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
if (sp->req_header.rqs_entry_type != RQSTYPE_REQUEST) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR, notresp,
temp fix for internal queue overflow problem
1999-04-14 17:37:36 +00:00
sp->req_header.rqs_entry_type, oop, optr);
various fixes
2000-08-27 23:38:44 +00:00
MEMZERO(sp, sizeof (isphdr_t));
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
continue;
}
buddaboom = 1;
}
if (sp->req_header.rqs_flags & 0xf) {
temp fix for internal queue overflow problem
1999-04-14 17:37:36 +00:00
#define _RQS_OFLAGS \
~(RQSFLAG_CONTINUATION|RQSFLAG_FULL|RQSFLAG_BADHEADER|RQSFLAG_BADPACKET)
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
if (sp->req_header.rqs_flags & RQSFLAG_CONTINUATION) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGWARN,
"continuation segment");
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
ISP_WRITE(isp, INMAILBOX5, optr);
continue;
}
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
if (sp->req_header.rqs_flags & RQSFLAG_FULL) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGDEBUG1,
"internal queues full");
temp fix for internal queue overflow problem
1999-04-14 17:37:36 +00:00
/*
* We'll synthesize a QUEUE FULL message below.
*/
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
}
if (sp->req_header.rqs_flags & RQSFLAG_BADHEADER) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR, "bad header flag");
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
buddaboom++;
}
if (sp->req_header.rqs_flags & RQSFLAG_BADPACKET) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR, "bad request packet");
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
buddaboom++;
}
temp fix for internal queue overflow problem
1999-04-14 17:37:36 +00:00
if (sp->req_header.rqs_flags & _RQS_OFLAGS) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR,
"unknown flags (0x%x) in response",
sp->req_header.rqs_flags);
temp fix for internal queue overflow problem
1999-04-14 17:37:36 +00:00
buddaboom++;
}
#undef _RQS_OFLAGS
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
if (sp->req_handle > isp->isp_maxcmds || sp->req_handle < 1) {
various fixes
2000-08-27 23:38:44 +00:00
MEMZERO(sp, sizeof (isphdr_t));
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR,
"bad request handle %d", sp->req_handle);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
ISP_WRITE(isp, INMAILBOX5, optr);
continue;
}
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
xs = isp_find_xs(isp, sp->req_handle);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
if (xs == NULL) {
various fixes
2000-08-27 23:38:44 +00:00
MEMZERO(sp, sizeof (isphdr_t));
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR,
"cannot find handle 0x%x in xflist",
sp->req_handle);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
ISP_WRITE(isp, INMAILBOX5, optr);
continue;
}
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
isp_destroy_handle(isp, sp->req_handle);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
if (sp->req_status_flags & RQSTF_BUS_RESET) {
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
isp->isp_sendmarker |= (1 << XS_CHANNEL(xs));
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
if (buddaboom) {
XS_SETERR(xs, HBA_BOTCH);
}
various fixes
2000-08-27 23:38:44 +00:00
if (IS_FC(isp) && (sp->req_scsi_status & RQCS_SV)) {
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
/*
various fixes
2000-08-27 23:38:44 +00:00
* Fibre Channel F/W doesn't say we got status
* if there's Sense Data instead. I guess they
* think it goes w/o saying.
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
*/
various fixes
2000-08-27 23:38:44 +00:00
sp->req_state_flags |= RQSF_GOT_STATUS;
}
if (sp->req_state_flags & RQSF_GOT_STATUS) {
*XS_STSP(xs) = sp->req_scsi_status & 0xff;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
various fixes
2000-08-27 23:38:44 +00:00
switch (sp->req_header.rqs_entry_type) {
case RQSTYPE_RESPONSE:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
XS_SET_STATE_STAT(isp, xs, sp);
isp_parse_status(isp, sp, xs);
if ((XS_NOERR(xs) || XS_ERR(xs) == HBA_NOERROR) &&
(*XS_STSP(xs) == SCSI_BUSY)) {
XS_SETERR(xs, HBA_TGTBSY);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
}
various fixes
2000-08-27 23:38:44 +00:00
if (IS_SCSI(isp)) {
XS_RESID(xs) = sp->req_resid;
if ((sp->req_state_flags & RQSF_GOT_STATUS) &&
(*XS_STSP(xs) == SCSI_CHECK) &&
(sp->req_state_flags & RQSF_GOT_SENSE)) {
XS_SAVE_SENSE(xs, sp);
}
/*
* A new synchronous rate was negotiated for
* this target. Mark state such that we'll go
* look up that which has changed later.
*/
if (sp->req_status_flags & RQSTF_NEGOTIATION) {
int t = XS_TGT(xs);
sdparam *sdp = isp->isp_param;
sdp += XS_CHANNEL(xs);
sdp->isp_devparam[t].dev_refresh = 1;
isp->isp_update |=
(1 << XS_CHANNEL(xs));
}
} else {
if (sp->req_status_flags & RQSF_XFER_COMPLETE) {
XS_RESID(xs) = 0;
} else if (sp->req_scsi_status & RQCS_RESID) {
XS_RESID(xs) = sp->req_resid;
} else {
XS_RESID(xs) = 0;
}
if ((sp->req_state_flags & RQSF_GOT_STATUS) &&
(*XS_STSP(xs) == SCSI_CHECK) &&
(sp->req_scsi_status & RQCS_SV)) {
XS_SAVE_SENSE(xs, sp);
}
}
isp_prt(isp, ISP_LOGDEBUG2, "asked for %d got resid %d",
XS_XFRLEN(xs), sp->req_resid);
break;
case RQSTYPE_REQUEST:
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
if (sp->req_header.rqs_flags & RQSFLAG_FULL) {
/*
* Force Queue Full status.
*/
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
*XS_STSP(xs) = SCSI_QFULL;
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
XS_SETERR(xs, HBA_NOERROR);
} else if (XS_NOERR(xs)) {
XS_SETERR(xs, HBA_BOTCH);
}
various fixes
2000-08-27 23:38:44 +00:00
XS_RESID(xs) = XS_XFRLEN(xs);
break;
default:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGWARN,
"unhandled respose queue type 0x%x",
sp->req_header.rqs_entry_type);
Add some prototype deadchip detection. Set FIFO bursting (1XX0 only- it's already on for the 2XX0) and detect the broken 1040A FIFO. Change bzero to MEMZERO (portability with **nux). Use memcpy for same reason. Finally detect QUEUE FULL conditions and return this as an error that will get cam_periph_error to do it's 'tagged openings now XXX' dance.
1999-01-10 02:55:10 +00:00
if (XS_NOERR(xs)) {
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
XS_SETERR(xs, HBA_BOTCH);
Add some prototype deadchip detection. Set FIFO bursting (1XX0 only- it's already on for the 2XX0) and detect the broken 1040A FIFO. Change bzero to MEMZERO (portability with **nux). Use memcpy for same reason. Finally detect QUEUE FULL conditions and return this as an error that will get cam_periph_error to do it's 'tagged openings now XXX' dance.
1999-01-10 02:55:10 +00:00
}
various fixes
2000-08-27 23:38:44 +00:00
break;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
various fixes
2000-08-27 23:38:44 +00:00
/*
* Free any dma resources. As a side effect, this may
* also do any cache flushing necessary for data coherence. */
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
if (XS_XFRLEN(xs)) {
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
ISP_DMAFREE(isp, xs, sp->req_handle);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
various fixes
2000-08-27 23:38:44 +00:00
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
if (((isp->isp_dblev & (ISP_LOGDEBUG2|ISP_LOGDEBUG3))) ||
((isp->isp_dblev & ISP_LOGDEBUG1) && !XS_NOERR(xs))) {
char skey;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
if (sp->req_state_flags & RQSF_GOT_SENSE) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
skey = XS_SNSKEY(xs) & 0xf;
if (skey < 10)
skey += '0';
else
skey += 'a';
} else if (*XS_STSP(xs) == SCSI_CHECK) {
skey = '?';
} else {
skey = '.';
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGALL, finmsg, XS_CHANNEL(xs),
XS_TGT(xs), XS_LUN(xs), XS_XFRLEN(xs), XS_RESID(xs),
*XS_STSP(xs), skey, XS_ERR(xs));
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
Remove the Target mode functions until they're in better shape. Implement some suggested compilation cleanups from Eklund. Wire down a hard loop id if we are not on a platform that has the ability to get to a PCI BIOS (it still will float to the ID it gets after a LIP but at least we can try). Clarify that the expanded lun is based upon SCCLUN defines (in f/w).
1998-12-05 01:33:57 +00:00
if (isp->isp_nactive > 0)
isp->isp_nactive--;
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
complist[ndone++] = xs; /* defer completion call until later */
various fixes
2000-08-27 23:38:44 +00:00
MEMZERO(sp, sizeof (isphdr_t));
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
if (ndone == MAX_REQUESTQ_COMPLETIONS) {
break;
}
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
}
Roll internal release tag. Print out if we're in a 64 bit PCI slot. Use fast memory timing NVRAM parameter. Clean up and fix establishment of default target parameters. Don't use NVRAM if are flagged as not to do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC mode but disabled disconnect/reconnect and wide!!). Fix delays after resets. BUS resets not done in isp_init anymore- relegated to OS specific outer layers. Fix a buglet where you can get in a loop for a NULL xs in the completion list in isp_intr. Add in some defines that can disable fast posting. Add in code for Loop Up/Loop Down events that call into the outer layers as to what to do.
1999-02-09 01:07:06 +00:00
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
/*
Roll internal release tag. Print out if we're in a 64 bit PCI slot. Use fast memory timing NVRAM parameter. Clean up and fix establishment of default target parameters. Don't use NVRAM if are flagged as not to do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC mode but disabled disconnect/reconnect and wide!!). Fix delays after resets. BUS resets not done in isp_init anymore- relegated to OS specific outer layers. Fix a buglet where you can get in a loop for a NULL xs in the completion list in isp_intr. Add in some defines that can disable fast posting. Add in code for Loop Up/Loop Down events that call into the outer layers as to what to do.
1999-02-09 01:07:06 +00:00
* If we looked at any commands, then it's valid to find out
* what the outpointer is. It also is a trigger to update the
* ISP's notion of what we've seen so far.
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
*/
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
if (nlooked) {
Roll internal release tag. Print out if we're in a 64 bit PCI slot. Use fast memory timing NVRAM parameter. Clean up and fix establishment of default target parameters. Don't use NVRAM if are flagged as not to do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC mode but disabled disconnect/reconnect and wide!!). Fix delays after resets. BUS resets not done in isp_init anymore- relegated to OS specific outer layers. Fix a buglet where you can get in a loop for a NULL xs in the completion list in isp_intr. Add in some defines that can disable fast posting. Add in code for Loop Up/Loop Down events that call into the outer layers as to what to do.
1999-02-09 01:07:06 +00:00
ISP_WRITE(isp, INMAILBOX5, optr);
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
isp->isp_reqodx = ISP_READ(isp, OUTMAILBOX4);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
isp->isp_residx = optr;
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
for (i = 0; i < ndone; i++) {
xs = complist[i];
if (xs) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_done(xs);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
}
}
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
return (1);
}
/*
* Support routines.
*/
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
static int
isp_parse_async(isp, mbox)
struct ispsoftc *isp;
Remove the Target mode functions until they're in better shape. Implement some suggested compilation cleanups from Eklund. Wire down a hard loop id if we are not on a platform that has the ability to get to a PCI BIOS (it still will float to the ID it gets after a LIP but at least we can try). Clarify that the expanded lun is based upon SCCLUN defines (in f/w).
1998-12-05 01:33:57 +00:00
int mbox;
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
{
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
int bus;
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
u_int32_t fast_post_handle = 0;
Add Dual LVD bus (1280) support
1999-12-16 05:42:02 +00:00
if (IS_DUALBUS(isp)) {
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
bus = ISP_READ(isp, OUTMAILBOX6);
} else {
bus = 0;
}
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
switch (mbox) {
case ASYNC_BUS_RESET:
Pick up topology more sanely at f/w startup. Change the restrictions of where we can have targets (based on topology). Much more importantly, make sure all mods to isp_sendmarker or |= so we don't lose the marking of a bus that needs to have a marker sent for it.
2000-04-21 02:04:34 +00:00
isp->isp_sendmarker |= (1 << bus);
Remove the Target mode functions until they're in better shape. Implement some suggested compilation cleanups from Eklund. Wire down a hard loop id if we are not on a platform that has the ability to get to a PCI BIOS (it still will float to the ID it gets after a LIP but at least we can try). Clarify that the expanded lun is based upon SCCLUN defines (in f/w).
1998-12-05 01:33:57 +00:00
#ifdef ISP_TARGET_MODE
Raise default FCP logintime to 60 seconds. Move the position of where we could have seen the loop up at least once so it makes sense. Change some stuff in ispscsicmd so we don't get stuck there if the loop has never come up yet. Add in some target mode support code.
2000-01-03 23:52:41 +00:00
isp_target_async(isp, bus, mbox);
Remove the Target mode functions until they're in better shape. Implement some suggested compilation cleanups from Eklund. Wire down a hard loop id if we are not on a platform that has the ability to get to a PCI BIOS (it still will float to the ID it gets after a LIP but at least we can try). Clarify that the expanded lun is based upon SCCLUN defines (in f/w).
1998-12-05 01:33:57 +00:00
#endif
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
isp_async(isp, ISPASYNC_BUS_RESET, &bus);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case ASYNC_SYSTEM_ERROR:
mbox = ISP_READ(isp, OUTMAILBOX1);
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR,
"Internal FW Error @ RISC Addr 0x%x", mbox);
isp_reinit(isp);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
/* no point continuing after this */
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
return (-1);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
case ASYNC_RQS_XFER_ERR:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR, "Request Queue Transfer Error");
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case ASYNC_RSP_XFER_ERR:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR, "Response Queue Transfer Error");
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case ASYNC_QWAKEUP:
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
/*
* We've just been notified that the Queue has woken up.
* We don't need to be chatty about this- just unlatch things
* and move on.
*/
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
mbox = ISP_READ(isp, OUTMAILBOX4);
break;
case ASYNC_TIMEOUT_RESET:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGWARN,
"timeout initiated SCSI bus reset of bus %d\n", bus);
Pick up topology more sanely at f/w startup. Change the restrictions of where we can have targets (based on topology). Much more importantly, make sure all mods to isp_sendmarker or |= so we don't lose the marking of a bus that needs to have a marker sent for it.
2000-04-21 02:04:34 +00:00
isp->isp_sendmarker |= (1 << bus);
Remove the Target mode functions until they're in better shape. Implement some suggested compilation cleanups from Eklund. Wire down a hard loop id if we are not on a platform that has the ability to get to a PCI BIOS (it still will float to the ID it gets after a LIP but at least we can try). Clarify that the expanded lun is based upon SCCLUN defines (in f/w).
1998-12-05 01:33:57 +00:00
#ifdef ISP_TARGET_MODE
Raise default FCP logintime to 60 seconds. Move the position of where we could have seen the loop up at least once so it makes sense. Change some stuff in ispscsicmd so we don't get stuck there if the loop has never come up yet. Add in some target mode support code.
2000-01-03 23:52:41 +00:00
isp_target_async(isp, bus, mbox);
Remove the Target mode functions until they're in better shape. Implement some suggested compilation cleanups from Eklund. Wire down a hard loop id if we are not on a platform that has the ability to get to a PCI BIOS (it still will float to the ID it gets after a LIP but at least we can try). Clarify that the expanded lun is based upon SCCLUN defines (in f/w).
1998-12-05 01:33:57 +00:00
#endif
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
Remove the Target mode functions until they're in better shape. Implement some suggested compilation cleanups from Eklund. Wire down a hard loop id if we are not on a platform that has the ability to get to a PCI BIOS (it still will float to the ID it gets after a LIP but at least we can try). Clarify that the expanded lun is based upon SCCLUN defines (in f/w).
1998-12-05 01:33:57 +00:00
case ASYNC_DEVICE_RESET:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGINFO, "device reset on bus %d", bus);
Pick up topology more sanely at f/w startup. Change the restrictions of where we can have targets (based on topology). Much more importantly, make sure all mods to isp_sendmarker or |= so we don't lose the marking of a bus that needs to have a marker sent for it.
2000-04-21 02:04:34 +00:00
isp->isp_sendmarker |= (1 << bus);
Remove the Target mode functions until they're in better shape. Implement some suggested compilation cleanups from Eklund. Wire down a hard loop id if we are not on a platform that has the ability to get to a PCI BIOS (it still will float to the ID it gets after a LIP but at least we can try). Clarify that the expanded lun is based upon SCCLUN defines (in f/w).
1998-12-05 01:33:57 +00:00
#ifdef ISP_TARGET_MODE
Raise default FCP logintime to 60 seconds. Move the position of where we could have seen the loop up at least once so it makes sense. Change some stuff in ispscsicmd so we don't get stuck there if the loop has never come up yet. Add in some target mode support code.
2000-01-03 23:52:41 +00:00
isp_target_async(isp, bus, mbox);
Remove the Target mode functions until they're in better shape. Implement some suggested compilation cleanups from Eklund. Wire down a hard loop id if we are not on a platform that has the ability to get to a PCI BIOS (it still will float to the ID it gets after a LIP but at least we can try). Clarify that the expanded lun is based upon SCCLUN defines (in f/w).
1998-12-05 01:33:57 +00:00
#endif
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case ASYNC_EXTMSG_UNDERRUN:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGWARN, "extended message underrun");
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case ASYNC_SCAM_INT:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGINFO, "SCAM interrupt");
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case ASYNC_HUNG_SCSI:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR,
"stalled SCSI Bus after DATA Overrun");
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
/* XXX: Need to issue SCSI reset at this point */
break;
case ASYNC_KILLED_BUS:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR, "SCSI Bus reset after DATA Overrun");
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case ASYNC_BUS_TRANSIT:
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
mbox = ISP_READ(isp, OUTMAILBOX2);
switch (mbox & 0x1c00) {
case SXP_PINS_LVD_MODE:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGINFO, "Transition to LVD mode");
various fixes
2000-08-27 23:38:44 +00:00
SDPARAM(isp)->isp_diffmode = 0;
SDPARAM(isp)->isp_ultramode = 0;
SDPARAM(isp)->isp_lvdmode = 1;
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
break;
case SXP_PINS_HVD_MODE:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGINFO,
"Transition to Differential mode");
various fixes
2000-08-27 23:38:44 +00:00
SDPARAM(isp)->isp_diffmode = 1;
SDPARAM(isp)->isp_ultramode = 0;
SDPARAM(isp)->isp_lvdmode = 0;
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
break;
case SXP_PINS_SE_MODE:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGINFO,
"Transition to Single Ended mode");
various fixes
2000-08-27 23:38:44 +00:00
SDPARAM(isp)->isp_diffmode = 0;
SDPARAM(isp)->isp_ultramode = 1;
SDPARAM(isp)->isp_lvdmode = 0;
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
break;
default:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGWARN,
"Transition to Unknown Mode 0x%x", mbox);
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
break;
}
/*
* XXX: Set up to renegotiate again!
*/
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
/* Can only be for a 1080... */
Pick up topology more sanely at f/w startup. Change the restrictions of where we can have targets (based on topology). Much more importantly, make sure all mods to isp_sendmarker or |= so we don't lose the marking of a bus that needs to have a marker sent for it.
2000-04-21 02:04:34 +00:00
isp->isp_sendmarker |= (1 << bus);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case ASYNC_CMD_CMPLT:
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
fast_post_handle = (ISP_READ(isp, OUTMAILBOX2) << 16) |
ISP_READ(isp, OUTMAILBOX1);
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGDEBUG3, "fast post completion of %u",
fast_post_handle);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case ASYNC_CTIO_DONE:
various fixes
2000-08-27 23:38:44 +00:00
#ifdef ISP_TARGET_MODE
/*
* Bus gets overloaded with the handle. Dual bus
* cards don't put bus# into the handle.
*/
bus = (ISP_READ(isp, OUTMAILBOX2) << 16) |
ISP_READ(isp, OUTMAILBOX1);
isp_target_async(isp, bus, mbox);
#else
isp_prt(isp, ISP_LOGINFO, "Fast Posting CTIO done");
#endif
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case ASYNC_LIP_OCCURRED:
various fixes
2000-08-27 23:38:44 +00:00
FCPARAM(isp)->isp_lipseq =
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
ISP_READ(isp, OUTMAILBOX1);
various fixes
2000-08-27 23:38:44 +00:00
FCPARAM(isp)->isp_fwstate = FW_CONFIG_WAIT;
FCPARAM(isp)->isp_loopstate = LOOP_LIP_RCVD;
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
isp->isp_sendmarker = 1;
Make firmware revision a triple. Clean up some FC init stuff for board versions with no BIOS. Separate mailbox interrupts from IOCB interrupts. Read OUTMAILBOX5 while RISC_INT is active- not after you clear it (potential race condition). Clear out older broken BIG_ENDIAN goop. Don't negotiate narrow/async for LVD busses at startup if already in LVD mode. Note usage of presumptive 1040C revision. For all the LIP, PDB Changed, Loop UP/DOWN async events, mark fw state as unknown as well as marking the need to do a getpdb on targets- after a LIP for certain the f/w has to do PRLI/PLOGI for all targets again and marking f/w state as unknown gives us a fighting chance to (start to) hold up for that to complete.
1999-04-04 02:28:29 +00:00
isp_mark_getpdb_all(isp);
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGINFO, "LIP occurred");
Raise default FCP logintime to 60 seconds. Move the position of where we could have seen the loop up at least once so it makes sense. Change some stuff in ispscsicmd so we don't get stuck there if the loop has never come up yet. Add in some target mode support code.
2000-01-03 23:52:41 +00:00
#ifdef ISP_TARGET_MODE
isp_target_async(isp, bus, mbox);
#endif
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case ASYNC_LOOP_UP:
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
isp->isp_sendmarker = 1;
various fixes
2000-08-27 23:38:44 +00:00
FCPARAM(isp)->isp_fwstate = FW_CONFIG_WAIT;
FCPARAM(isp)->isp_loopstate = LOOP_LIP_RCVD;
Make firmware revision a triple. Clean up some FC init stuff for board versions with no BIOS. Separate mailbox interrupts from IOCB interrupts. Read OUTMAILBOX5 while RISC_INT is active- not after you clear it (potential race condition). Clear out older broken BIG_ENDIAN goop. Don't negotiate narrow/async for LVD busses at startup if already in LVD mode. Note usage of presumptive 1040C revision. For all the LIP, PDB Changed, Loop UP/DOWN async events, mark fw state as unknown as well as marking the need to do a getpdb on targets- after a LIP for certain the f/w has to do PRLI/PLOGI for all targets again and marking f/w state as unknown gives us a fighting chance to (start to) hold up for that to complete.
1999-04-04 02:28:29 +00:00
isp_mark_getpdb_all(isp);
Roll internal release tag. Print out if we're in a 64 bit PCI slot. Use fast memory timing NVRAM parameter. Clean up and fix establishment of default target parameters. Don't use NVRAM if are flagged as not to do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC mode but disabled disconnect/reconnect and wide!!). Fix delays after resets. BUS resets not done in isp_init anymore- relegated to OS specific outer layers. Fix a buglet where you can get in a loop for a NULL xs in the completion list in isp_intr. Add in some defines that can disable fast posting. Add in code for Loop Up/Loop Down events that call into the outer layers as to what to do.
1999-02-09 01:07:06 +00:00
isp_async(isp, ISPASYNC_LOOP_UP, NULL);
Raise default FCP logintime to 60 seconds. Move the position of where we could have seen the loop up at least once so it makes sense. Change some stuff in ispscsicmd so we don't get stuck there if the loop has never come up yet. Add in some target mode support code.
2000-01-03 23:52:41 +00:00
#ifdef ISP_TARGET_MODE
isp_target_async(isp, bus, mbox);
#endif
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case ASYNC_LOOP_DOWN:
Make firmware revision a triple. Clean up some FC init stuff for board versions with no BIOS. Separate mailbox interrupts from IOCB interrupts. Read OUTMAILBOX5 while RISC_INT is active- not after you clear it (potential race condition). Clear out older broken BIG_ENDIAN goop. Don't negotiate narrow/async for LVD busses at startup if already in LVD mode. Note usage of presumptive 1040C revision. For all the LIP, PDB Changed, Loop UP/DOWN async events, mark fw state as unknown as well as marking the need to do a getpdb on targets- after a LIP for certain the f/w has to do PRLI/PLOGI for all targets again and marking f/w state as unknown gives us a fighting chance to (start to) hold up for that to complete.
1999-04-04 02:28:29 +00:00
isp->isp_sendmarker = 1;
various fixes
2000-08-27 23:38:44 +00:00
FCPARAM(isp)->isp_fwstate = FW_CONFIG_WAIT;
FCPARAM(isp)->isp_loopstate = LOOP_NIL;
Make firmware revision a triple. Clean up some FC init stuff for board versions with no BIOS. Separate mailbox interrupts from IOCB interrupts. Read OUTMAILBOX5 while RISC_INT is active- not after you clear it (potential race condition). Clear out older broken BIG_ENDIAN goop. Don't negotiate narrow/async for LVD busses at startup if already in LVD mode. Note usage of presumptive 1040C revision. For all the LIP, PDB Changed, Loop UP/DOWN async events, mark fw state as unknown as well as marking the need to do a getpdb on targets- after a LIP for certain the f/w has to do PRLI/PLOGI for all targets again and marking f/w state as unknown gives us a fighting chance to (start to) hold up for that to complete.
1999-04-04 02:28:29 +00:00
isp_mark_getpdb_all(isp);
Roll internal release tag. Print out if we're in a 64 bit PCI slot. Use fast memory timing NVRAM parameter. Clean up and fix establishment of default target parameters. Don't use NVRAM if are flagged as not to do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC mode but disabled disconnect/reconnect and wide!!). Fix delays after resets. BUS resets not done in isp_init anymore- relegated to OS specific outer layers. Fix a buglet where you can get in a loop for a NULL xs in the completion list in isp_intr. Add in some defines that can disable fast posting. Add in code for Loop Up/Loop Down events that call into the outer layers as to what to do.
1999-02-09 01:07:06 +00:00
isp_async(isp, ISPASYNC_LOOP_DOWN, NULL);
Raise default FCP logintime to 60 seconds. Move the position of where we could have seen the loop up at least once so it makes sense. Change some stuff in ispscsicmd so we don't get stuck there if the loop has never come up yet. Add in some target mode support code.
2000-01-03 23:52:41 +00:00
#ifdef ISP_TARGET_MODE
isp_target_async(isp, bus, mbox);
#endif
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case ASYNC_LOOP_RESET:
Pick up topology more sanely at f/w startup. Change the restrictions of where we can have targets (based on topology). Much more importantly, make sure all mods to isp_sendmarker or |= so we don't lose the marking of a bus that needs to have a marker sent for it.
2000-04-21 02:04:34 +00:00
isp->isp_sendmarker = 1;
various fixes
2000-08-27 23:38:44 +00:00
FCPARAM(isp)->isp_fwstate = FW_CONFIG_WAIT;
FCPARAM(isp)->isp_loopstate = LOOP_NIL;
Make firmware revision a triple. Clean up some FC init stuff for board versions with no BIOS. Separate mailbox interrupts from IOCB interrupts. Read OUTMAILBOX5 while RISC_INT is active- not after you clear it (potential race condition). Clear out older broken BIG_ENDIAN goop. Don't negotiate narrow/async for LVD busses at startup if already in LVD mode. Note usage of presumptive 1040C revision. For all the LIP, PDB Changed, Loop UP/DOWN async events, mark fw state as unknown as well as marking the need to do a getpdb on targets- after a LIP for certain the f/w has to do PRLI/PLOGI for all targets again and marking f/w state as unknown gives us a fighting chance to (start to) hold up for that to complete.
1999-04-04 02:28:29 +00:00
isp_mark_getpdb_all(isp);
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGINFO, "Loop RESET");
Remove the Target mode functions until they're in better shape. Implement some suggested compilation cleanups from Eklund. Wire down a hard loop id if we are not on a platform that has the ability to get to a PCI BIOS (it still will float to the ID it gets after a LIP but at least we can try). Clarify that the expanded lun is based upon SCCLUN defines (in f/w).
1998-12-05 01:33:57 +00:00
#ifdef ISP_TARGET_MODE
Raise default FCP logintime to 60 seconds. Move the position of where we could have seen the loop up at least once so it makes sense. Change some stuff in ispscsicmd so we don't get stuck there if the loop has never come up yet. Add in some target mode support code.
2000-01-03 23:52:41 +00:00
isp_target_async(isp, bus, mbox);
Remove the Target mode functions until they're in better shape. Implement some suggested compilation cleanups from Eklund. Wire down a hard loop id if we are not on a platform that has the ability to get to a PCI BIOS (it still will float to the ID it gets after a LIP but at least we can try). Clarify that the expanded lun is based upon SCCLUN defines (in f/w).
1998-12-05 01:33:57 +00:00
#endif
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case ASYNC_PDB_CHANGED:
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
isp->isp_sendmarker = 1;
various fixes
2000-08-27 23:38:44 +00:00
FCPARAM(isp)->isp_loopstate = LOOP_PDB_RCVD;
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
isp_mark_getpdb_all(isp);
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGINFO, "Port Database Changed");
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case ASYNC_CHANGE_NOTIFY:
More code cleanup. Go back to using FULL_LOGIN Fibre Chan if f/w is less than 1.17.0 level. Change where we do the loop database init. Add in the CMD_RQLATER return. Add some register debounce.
1999-08-16 19:59:55 +00:00
isp_mark_getpdb_all(isp);
/*
* Not correct, but it will force us to rescan the loop.
*/
various fixes
2000-08-27 23:38:44 +00:00
FCPARAM(isp)->isp_loopstate = LOOP_PDB_RCVD;
More code cleanup. Go back to using FULL_LOGIN Fibre Chan if f/w is less than 1.17.0 level. Change where we do the loop database init. Add in the CMD_RQLATER return. Add some register debounce.
1999-08-16 19:59:55 +00:00
isp_async(isp, ISPASYNC_CHANGE_NOTIFY, NULL);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
Restructure nvram reading routine to split out to separate functions for 1020/1X80/12160/2X00- for readability. Add in 12160 (Ultra3) support- but not with PPR just yet. Fix and clarify fetching of return parameter for getting firmware rev which for the 2200 contains the connection topology (Private Loop (NL-port), N-port, FL-port, F-port). Synthesize the connection topology for the 2100 which can only be Private Loop or FL-port. Handle a couple of new async mailbox commands which signify connection in Point-to-Point mode (N-port or F-port) or indicate various toe stubbing getting to same. Approved: jkh@freebsd.org
2000-02-11 19:31:32 +00:00
case ASYNC_PTPMODE:
various fixes
2000-08-27 23:38:44 +00:00
if (FCPARAM(isp)->isp_onfabric)
FCPARAM(isp)->isp_topo = TOPO_N_PORT;
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
else
various fixes
2000-08-27 23:38:44 +00:00
FCPARAM(isp)->isp_topo = TOPO_F_PORT;
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
isp_mark_getpdb_all(isp);
isp->isp_sendmarker = 1;
various fixes
2000-08-27 23:38:44 +00:00
FCPARAM(isp)->isp_fwstate = FW_CONFIG_WAIT;
FCPARAM(isp)->isp_loopstate = LOOP_LIP_RCVD;
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
#ifdef ISP_TARGET_MODE
isp_target_async(isp, bus, mbox);
#endif
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGINFO, "Point-to-Point mode");
Restructure nvram reading routine to split out to separate functions for 1020/1X80/12160/2X00- for readability. Add in 12160 (Ultra3) support- but not with PPR just yet. Fix and clarify fetching of return parameter for getting firmware rev which for the 2200 contains the connection topology (Private Loop (NL-port), N-port, FL-port, F-port). Synthesize the connection topology for the 2100 which can only be Private Loop or FL-port. Handle a couple of new async mailbox commands which signify connection in Point-to-Point mode (N-port or F-port) or indicate various toe stubbing getting to same. Approved: jkh@freebsd.org
2000-02-11 19:31:32 +00:00
break;
case ASYNC_CONNMODE:
mbox = ISP_READ(isp, OUTMAILBOX1);
switch (mbox) {
case ISP_CONN_LOOP:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGINFO, "Point-to-Point->Loop mode");
Restructure nvram reading routine to split out to separate functions for 1020/1X80/12160/2X00- for readability. Add in 12160 (Ultra3) support- but not with PPR just yet. Fix and clarify fetching of return parameter for getting firmware rev which for the 2200 contains the connection topology (Private Loop (NL-port), N-port, FL-port, F-port). Synthesize the connection topology for the 2100 which can only be Private Loop or FL-port. Handle a couple of new async mailbox commands which signify connection in Point-to-Point mode (N-port or F-port) or indicate various toe stubbing getting to same. Approved: jkh@freebsd.org
2000-02-11 19:31:32 +00:00
break;
case ISP_CONN_PTP:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGINFO, "Loop->Point-to-Point mode");
Restructure nvram reading routine to split out to separate functions for 1020/1X80/12160/2X00- for readability. Add in 12160 (Ultra3) support- but not with PPR just yet. Fix and clarify fetching of return parameter for getting firmware rev which for the 2200 contains the connection topology (Private Loop (NL-port), N-port, FL-port, F-port). Synthesize the connection topology for the 2100 which can only be Private Loop or FL-port. Handle a couple of new async mailbox commands which signify connection in Point-to-Point mode (N-port or F-port) or indicate various toe stubbing getting to same. Approved: jkh@freebsd.org
2000-02-11 19:31:32 +00:00
break;
case ISP_CONN_BADLIP:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGWARN,
"Point-to-Point->Loop mode (1)");
Restructure nvram reading routine to split out to separate functions for 1020/1X80/12160/2X00- for readability. Add in 12160 (Ultra3) support- but not with PPR just yet. Fix and clarify fetching of return parameter for getting firmware rev which for the 2200 contains the connection topology (Private Loop (NL-port), N-port, FL-port, F-port). Synthesize the connection topology for the 2100 which can only be Private Loop or FL-port. Handle a couple of new async mailbox commands which signify connection in Point-to-Point mode (N-port or F-port) or indicate various toe stubbing getting to same. Approved: jkh@freebsd.org
2000-02-11 19:31:32 +00:00
break;
case ISP_CONN_FATAL:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR, "FATAL CONNECTION ERROR");
isp_reinit(isp);
Restructure nvram reading routine to split out to separate functions for 1020/1X80/12160/2X00- for readability. Add in 12160 (Ultra3) support- but not with PPR just yet. Fix and clarify fetching of return parameter for getting firmware rev which for the 2200 contains the connection topology (Private Loop (NL-port), N-port, FL-port, F-port). Synthesize the connection topology for the 2100 which can only be Private Loop or FL-port. Handle a couple of new async mailbox commands which signify connection in Point-to-Point mode (N-port or F-port) or indicate various toe stubbing getting to same. Approved: jkh@freebsd.org
2000-02-11 19:31:32 +00:00
/* no point continuing after this */
return (-1);
case ISP_CONN_LOOPBACK:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGWARN,
"Looped Back in Point-to-Point mode");
Restructure nvram reading routine to split out to separate functions for 1020/1X80/12160/2X00- for readability. Add in 12160 (Ultra3) support- but not with PPR just yet. Fix and clarify fetching of return parameter for getting firmware rev which for the 2200 contains the connection topology (Private Loop (NL-port), N-port, FL-port, F-port). Synthesize the connection topology for the 2100 which can only be Private Loop or FL-port. Handle a couple of new async mailbox commands which signify connection in Point-to-Point mode (N-port or F-port) or indicate various toe stubbing getting to same. Approved: jkh@freebsd.org
2000-02-11 19:31:32 +00:00
}
break;
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
default:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGWARN, "Unknown Async Code 0x%x", mbox);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
}
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
return (fast_post_handle);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
}
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
/*
* Handle other response entries. A pointer to the request queue output
* index is here in case we want to eat several entries at once, although
* this is not used currently.
*/
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
static int
isp_handle_other_response(isp, sp, optrp)
struct ispsoftc *isp;
ispstatusreq_t *sp;
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
u_int16_t *optrp;
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
{
switch (sp->req_header.rqs_entry_type) {
various fixes
2000-08-27 23:38:44 +00:00
case RQSTYPE_STATUS_CONT:
isp_prt(isp, ISP_LOGINFO, "Ignored Continuation Response");
return (0);
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
case RQSTYPE_ATIO:
Raise default FCP logintime to 60 seconds. Move the position of where we could have seen the loop up at least once so it makes sense. Change some stuff in ispscsicmd so we don't get stuck there if the loop has never come up yet. Add in some target mode support code.
2000-01-03 23:52:41 +00:00
case RQSTYPE_CTIO:
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
case RQSTYPE_ENABLE_LUN:
Remove the Target mode functions until they're in better shape. Implement some suggested compilation cleanups from Eklund. Wire down a hard loop id if we are not on a platform that has the ability to get to a PCI BIOS (it still will float to the ID it gets after a LIP but at least we can try). Clarify that the expanded lun is based upon SCCLUN defines (in f/w).
1998-12-05 01:33:57 +00:00
case RQSTYPE_MODIFY_LUN:
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
case RQSTYPE_NOTIFY:
case RQSTYPE_NOTIFY_ACK:
case RQSTYPE_CTIO1:
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
case RQSTYPE_ATIO2:
case RQSTYPE_CTIO2:
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
case RQSTYPE_CTIO3:
#ifdef ISP_TARGET_MODE
Raise default FCP logintime to 60 seconds. Move the position of where we could have seen the loop up at least once so it makes sense. Change some stuff in ispscsicmd so we don't get stuck there if the loop has never come up yet. Add in some target mode support code.
2000-01-03 23:52:41 +00:00
return (isp_target_notify(isp, sp, optrp));
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
#else
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
optrp = optrp;
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
/* FALLTHROUGH */
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
#endif
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
case RQSTYPE_REQUEST:
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
default:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGWARN, "Unhandled Response Type 0x%x",
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
sp->req_header.rqs_entry_type);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
return (-1);
}
}
Remove the Target mode functions until they're in better shape. Implement some suggested compilation cleanups from Eklund. Wire down a hard loop id if we are not on a platform that has the ability to get to a PCI BIOS (it still will float to the ID it gets after a LIP but at least we can try). Clarify that the expanded lun is based upon SCCLUN defines (in f/w).
1998-12-05 01:33:57 +00:00
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
static void
isp_parse_status(isp, sp, xs)
struct ispsoftc *isp;
ispstatusreq_t *sp;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
XS_T *xs;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
{
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
switch (sp->req_completion_status & 0xff) {
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
case RQCS_COMPLETE:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
if (XS_NOERR(xs)) {
XS_SETERR(xs, HBA_NOERROR);
}
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
return;
case RQCS_INCOMPLETE:
if ((sp->req_state_flags & RQSF_GOT_TARGET) == 0) {
various fixes
2000-08-27 23:38:44 +00:00
isp_prt(isp, ISP_LOGDEBUG1,
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
"Selection Timeout for %d.%d.%d",
XS_TGT(xs), XS_LUN(xs), XS_CHANNEL(xs));
if (XS_NOERR(xs)) {
XS_SETERR(xs, HBA_SELTIMEOUT);
}
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
return;
}
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR,
"command incomplete for %d.%d.%d, state 0x%x",
XS_CHANNEL(xs), XS_TGT(xs), XS_LUN(xs),
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
sp->req_state_flags);
break;
case RQCS_DMA_ERROR:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR, "DMA error for command on %d.%d.%d",
XS_CHANNEL(xs), XS_TGT(xs), XS_LUN(xs));
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
break;
case RQCS_TRANSPORT_ERROR:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
{
char buf[172];
buf[0] = 0;
STRNCAT(buf, "states=>", sizeof buf);
if (sp->req_state_flags & RQSF_GOT_BUS) {
STRNCAT(buf, " GOT_BUS", sizeof buf);
}
if (sp->req_state_flags & RQSF_GOT_TARGET) {
STRNCAT(buf, " GOT_TGT", sizeof buf);
}
if (sp->req_state_flags & RQSF_SENT_CDB) {
STRNCAT(buf, " SENT_CDB", sizeof buf);
}
if (sp->req_state_flags & RQSF_XFRD_DATA) {
STRNCAT(buf, " XFRD_DATA", sizeof buf);
}
if (sp->req_state_flags & RQSF_GOT_STATUS) {
STRNCAT(buf, " GOT_STS", sizeof buf);
}
if (sp->req_state_flags & RQSF_GOT_SENSE) {
STRNCAT(buf, " GOT_SNS", sizeof buf);
}
if (sp->req_state_flags & RQSF_XFER_COMPLETE) {
STRNCAT(buf, " XFR_CMPLT", sizeof buf);
}
STRNCAT(buf, "\nstatus=>", sizeof buf);
if (sp->req_status_flags & RQSTF_DISCONNECT) {
STRNCAT(buf, " Disconnect", sizeof buf);
}
if (sp->req_status_flags & RQSTF_SYNCHRONOUS) {
STRNCAT(buf, " Sync_xfr", sizeof buf);
}
if (sp->req_status_flags & RQSTF_PARITY_ERROR) {
STRNCAT(buf, " Parity", sizeof buf);
}
if (sp->req_status_flags & RQSTF_BUS_RESET) {
STRNCAT(buf, " Bus_Reset", sizeof buf);
}
if (sp->req_status_flags & RQSTF_DEVICE_RESET) {
STRNCAT(buf, " Device_Reset", sizeof buf);
}
if (sp->req_status_flags & RQSTF_ABORTED) {
STRNCAT(buf, " Aborted", sizeof buf);
}
if (sp->req_status_flags & RQSTF_TIMEOUT) {
STRNCAT(buf, " Timeout", sizeof buf);
}
if (sp->req_status_flags & RQSTF_NEGOTIATION) {
STRNCAT(buf, " Negotiation", sizeof buf);
}
isp_prt(isp, ISP_LOGERR, "%s", buf);
isp_prt(isp, ISP_LOGERR, "transport error for %d.%d.%d:\n%s",
XS_CHANNEL(xs), XS_TGT(xs), XS_LUN(xs), buf);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
break;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
}
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
case RQCS_RESET_OCCURRED:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGWARN,
"bus reset destroyed command for %d.%d.%d",
XS_CHANNEL(xs), XS_TGT(xs), XS_LUN(xs));
Slightly cleaner fabric support (whiter whites! redder reds!).. No, seriously- only attempt to logout a previously logged in fabric device. Fix a longstanding bug for aborting overtime commands- handle halves have always been reversed. Clean up some error messages to indicate channel number. Approved:jkh
2000-02-29 05:52:14 +00:00
isp->isp_sendmarker |= (1 << XS_CHANNEL(xs));
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
if (XS_NOERR(xs)) {
XS_SETERR(xs, HBA_BUSRESET);
}
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
return;
case RQCS_ABORTED:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR, "command aborted for %d.%d.%d",
XS_CHANNEL(xs), XS_TGT(xs), XS_LUN(xs));
Slightly cleaner fabric support (whiter whites! redder reds!).. No, seriously- only attempt to logout a previously logged in fabric device. Fix a longstanding bug for aborting overtime commands- handle halves have always been reversed. Clean up some error messages to indicate channel number. Approved:jkh
2000-02-29 05:52:14 +00:00
isp->isp_sendmarker |= (1 << XS_CHANNEL(xs));
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
if (XS_NOERR(xs)) {
XS_SETERR(xs, HBA_ABORTED);
}
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
return;
case RQCS_TIMEOUT:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGWARN, "command timed out for %d.%d.%d",
XS_CHANNEL(xs), XS_TGT(xs), XS_LUN(xs));
if (XS_NOERR(xs)) {
XS_SETERR(xs, HBA_CMDTIMEOUT);
}
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
return;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
case RQCS_DATA_OVERRUN:
various fixes
2000-08-27 23:38:44 +00:00
XS_RESID(xs) = sp->req_resid;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR, "data overrun for command on %d.%d.%d",
XS_CHANNEL(xs), XS_TGT(xs), XS_LUN(xs));
if (XS_NOERR(xs)) {
XS_SETERR(xs, HBA_DATAOVR);
}
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
return;
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
case RQCS_COMMAND_OVERRUN:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR,
"command overrun for command on %d.%d.%d",
XS_CHANNEL(xs), XS_TGT(xs), XS_LUN(xs));
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case RQCS_STATUS_OVERRUN:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR,
"status overrun for command on %d.%d.%d",
XS_CHANNEL(xs), XS_TGT(xs), XS_LUN(xs));
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case RQCS_BAD_MESSAGE:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR,
"msg not COMMAND COMPLETE after status %d.%d.%d",
XS_CHANNEL(xs), XS_TGT(xs), XS_LUN(xs));
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case RQCS_NO_MESSAGE_OUT:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR,
"No MESSAGE OUT phase after selection on %d.%d.%d",
XS_CHANNEL(xs), XS_TGT(xs), XS_LUN(xs));
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case RQCS_EXT_ID_FAILED:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR, "EXTENDED IDENTIFY failed %d.%d.%d",
XS_CHANNEL(xs), XS_TGT(xs), XS_LUN(xs));
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case RQCS_IDE_MSG_FAILED:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR,
"INITIATOR DETECTED ERROR rejected by %d.%d.%d",
XS_CHANNEL(xs), XS_TGT(xs), XS_LUN(xs));
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case RQCS_ABORT_MSG_FAILED:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR, "ABORT OPERATION rejected by %d.%d.%d",
XS_CHANNEL(xs), XS_TGT(xs), XS_LUN(xs));
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case RQCS_REJECT_MSG_FAILED:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR, "MESSAGE REJECT rejected by %d.%d.%d",
XS_CHANNEL(xs), XS_TGT(xs), XS_LUN(xs));
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case RQCS_NOP_MSG_FAILED:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR, "NOP rejected by %d.%d.%d",
XS_CHANNEL(xs), XS_TGT(xs), XS_LUN(xs));
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case RQCS_PARITY_ERROR_MSG_FAILED:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR,
"MESSAGE PARITY ERROR rejected by %d.%d.%d",
XS_CHANNEL(xs), XS_TGT(xs), XS_LUN(xs));
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case RQCS_DEVICE_RESET_MSG_FAILED:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGWARN,
"BUS DEVICE RESET rejected by %d.%d.%d",
XS_CHANNEL(xs), XS_TGT(xs), XS_LUN(xs));
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case RQCS_ID_MSG_FAILED:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR, "IDENTIFY rejected by %d.%d.%d",
XS_CHANNEL(xs), XS_TGT(xs), XS_LUN(xs));
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case RQCS_UNEXP_BUS_FREE:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR, "%d.%d.%d had an unexpected bus free",
XS_CHANNEL(xs), XS_TGT(xs), XS_LUN(xs));
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
case RQCS_DATA_UNDERRUN:
various fixes
2000-08-27 23:38:44 +00:00
XS_RESID(xs) = sp->req_resid;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
if (XS_NOERR(xs)) {
XS_SETERR(xs, HBA_NOERROR);
}
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
return;
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
case RQCS_XACT_ERR1:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR, xact1, XS_CHANNEL(xs),
Slightly cleaner fabric support (whiter whites! redder reds!).. No, seriously- only attempt to logout a previously logged in fabric device. Fix a longstanding bug for aborting overtime commands- handle halves have always been reversed. Clean up some error messages to indicate channel number. Approved:jkh
2000-02-29 05:52:14 +00:00
XS_TGT(xs), XS_LUN(xs));
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
case RQCS_XACT_ERR2:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR, xact2,
Slightly cleaner fabric support (whiter whites! redder reds!).. No, seriously- only attempt to logout a previously logged in fabric device. Fix a longstanding bug for aborting overtime commands- handle halves have always been reversed. Clean up some error messages to indicate channel number. Approved:jkh
2000-02-29 05:52:14 +00:00
XS_LUN(xs), XS_TGT(xs), XS_CHANNEL(xs));
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case RQCS_XACT_ERR3:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR, xact3, XS_TGT(xs),
XS_LUN(xs), XS_CHANNEL(xs));
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case RQCS_BAD_ENTRY:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR, "Invalid IOCB entry type detected");
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case RQCS_QUEUE_FULL:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGDEBUG1,
"internal queues full for %d.%d.%d status 0x%x", XS_TGT(xs),
XS_LUN(xs), XS_CHANNEL(xs), *XS_STSP(xs));
Add some prototype deadchip detection. Set FIFO bursting (1XX0 only- it's already on for the 2XX0) and detect the broken 1040A FIFO. Change bzero to MEMZERO (portability with **nux). Use memcpy for same reason. Finally detect QUEUE FULL conditions and return this as an error that will get cam_periph_error to do it's 'tagged openings now XXX' dance.
1999-01-10 02:55:10 +00:00
/*
* If QFULL or some other status byte is set, then this
* isn't an error, per se.
*/
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
if (*XS_STSP(xs) != SCSI_GOOD && XS_NOERR(xs)) {
Add some prototype deadchip detection. Set FIFO bursting (1XX0 only- it's already on for the 2XX0) and detect the broken 1040A FIFO. Change bzero to MEMZERO (portability with **nux). Use memcpy for same reason. Finally detect QUEUE FULL conditions and return this as an error that will get cam_periph_error to do it's 'tagged openings now XXX' dance.
1999-01-10 02:55:10 +00:00
XS_SETERR(xs, HBA_NOERROR);
return;
}
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case RQCS_PHASE_SKIPPED:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR, pskip,
XS_TGT(xs), XS_LUN(xs), XS_CHANNEL(xs));
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
case RQCS_ARQS_FAILED:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR,
"Auto Request Sense failed for %d.%d.%d",
XS_CHANNEL(xs), XS_TGT(xs), XS_LUN(xs));
if (XS_NOERR(xs)) {
XS_SETERR(xs, HBA_ARQFAIL);
}
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
return;
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
case RQCS_WIDE_FAILED:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR,
"Wide Negotiation failed for %d.%d.%d",
XS_TGT(xs), XS_LUN(xs), XS_CHANNEL(xs));
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
if (IS_SCSI(isp)) {
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
sdparam *sdp = isp->isp_param;
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
sdp += XS_CHANNEL(xs);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
sdp->isp_devparam[XS_TGT(xs)].dev_flags &= ~DPARM_WIDE;
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
sdp->isp_devparam[XS_TGT(xs)].dev_update = 1;
Slightly cleaner fabric support (whiter whites! redder reds!).. No, seriously- only attempt to logout a previously logged in fabric device. Fix a longstanding bug for aborting overtime commands- handle halves have always been reversed. Clean up some error messages to indicate channel number. Approved:jkh
2000-02-29 05:52:14 +00:00
isp->isp_update |= (1 << XS_CHANNEL(xs));
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
}
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
if (XS_NOERR(xs)) {
XS_SETERR(xs, HBA_NOERROR);
}
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
return;
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
case RQCS_SYNCXFER_FAILED:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR,
"SDTR Message failed for target %d.%d.%d",
XS_TGT(xs), XS_LUN(xs), XS_CHANNEL(xs));
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
if (IS_SCSI(isp)) {
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
sdparam *sdp = isp->isp_param;
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
sdp += XS_CHANNEL(xs);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
sdp->isp_devparam[XS_TGT(xs)].dev_flags &= ~DPARM_SYNC;
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
sdp->isp_devparam[XS_TGT(xs)].dev_update = 1;
Slightly cleaner fabric support (whiter whites! redder reds!).. No, seriously- only attempt to logout a previously logged in fabric device. Fix a longstanding bug for aborting overtime commands- handle halves have always been reversed. Clean up some error messages to indicate channel number. Approved:jkh
2000-02-29 05:52:14 +00:00
isp->isp_update |= (1 << XS_CHANNEL(xs));
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
}
break;
case RQCS_LVD_BUSERR:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR,
"Bad LVD condition while talking to %d.%d.%d",
XS_TGT(xs), XS_LUN(xs), XS_CHANNEL(xs));
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
break;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
case RQCS_PORT_UNAVAILABLE:
/*
* No such port on the loop. Moral equivalent of SELTIMEO
*/
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGINFO,
"Port Unavailable for target %d", XS_TGT(xs));
if (XS_NOERR(xs)) {
XS_SETERR(xs, HBA_SELTIMEOUT);
}
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
return;
case RQCS_PORT_LOGGED_OUT:
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
/*
* It was there (maybe)- treat as a selection timeout.
*/
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGINFO,
"port logout for target %d", XS_TGT(xs));
if (XS_NOERR(xs)) {
XS_SETERR(xs, HBA_SELTIMEOUT);
}
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
return;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
case RQCS_PORT_CHANGED:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGWARN,
"port changed for target %d", XS_TGT(xs));
if (XS_NOERR(xs)) {
XS_SETERR(xs, HBA_SELTIMEOUT);
}
Slightly cleaner fabric support (whiter whites! redder reds!).. No, seriously- only attempt to logout a previously logged in fabric device. Fix a longstanding bug for aborting overtime commands- handle halves have always been reversed. Clean up some error messages to indicate channel number. Approved:jkh
2000-02-29 05:52:14 +00:00
return;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
case RQCS_PORT_BUSY:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGWARN,
"port busy for target %d", XS_TGT(xs));
if (XS_NOERR(xs)) {
XS_SETERR(xs, HBA_TGTBSY);
}
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
return;
default:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR, "Unknown Completion Status 0x%x",
sp->req_completion_status);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
break;
}
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
if (XS_NOERR(xs)) {
XS_SETERR(xs, HBA_BOTCH);
}
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
static void
isp_fastpost_complete(isp, fph)
struct ispsoftc *isp;
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
u_int32_t fph;
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
{
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
XS_T *xs;
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
if (fph < 1) {
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
return;
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
}
xs = isp_find_xs(isp, fph);
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
if (xs == NULL) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGWARN,
"Command for fast post handle 0x%x not found", fph);
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
return;
}
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
isp_destroy_handle(isp, fph);
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
/*
* Since we don't have a result queue entry item,
* we must believe that SCSI status is zero and
* that all data transferred.
*/
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
XS_SET_STATE_STAT(isp, xs, NULL);
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
XS_RESID(xs) = 0;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
*XS_STSP(xs) = SCSI_GOOD;
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
if (XS_XFRLEN(xs)) {
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
ISP_DMAFREE(isp, xs, fph);
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
}
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
if (isp->isp_nactive)
isp->isp_nactive--;
various fixes
2000-08-27 23:38:44 +00:00
isp_done(xs);
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
}
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
#define HIBYT(x) ((x) >> 0x8)
#define LOBYT(x) ((x) & 0xff)
#define ISPOPMAP(a, b) (((a) << 8) | (b))
static u_int16_t mbpscsi[] = {
ISPOPMAP(0x01, 0x01), /* 0x00: MBOX_NO_OP */
ISPOPMAP(0x1f, 0x01), /* 0x01: MBOX_LOAD_RAM */
ISPOPMAP(0x03, 0x01), /* 0x02: MBOX_EXEC_FIRMWARE */
ISPOPMAP(0x1f, 0x01), /* 0x03: MBOX_DUMP_RAM */
ISPOPMAP(0x07, 0x07), /* 0x04: MBOX_WRITE_RAM_WORD */
ISPOPMAP(0x03, 0x07), /* 0x05: MBOX_READ_RAM_WORD */
ISPOPMAP(0x3f, 0x3f), /* 0x06: MBOX_MAILBOX_REG_TEST */
ISPOPMAP(0x03, 0x07), /* 0x07: MBOX_VERIFY_CHECKSUM */
ISPOPMAP(0x01, 0x0f), /* 0x08: MBOX_ABOUT_FIRMWARE */
ISPOPMAP(0x00, 0x00), /* 0x09: */
ISPOPMAP(0x00, 0x00), /* 0x0a: */
ISPOPMAP(0x00, 0x00), /* 0x0b: */
ISPOPMAP(0x00, 0x00), /* 0x0c: */
ISPOPMAP(0x00, 0x00), /* 0x0d: */
ISPOPMAP(0x01, 0x05), /* 0x0e: MBOX_CHECK_FIRMWARE */
ISPOPMAP(0x00, 0x00), /* 0x0f: */
ISPOPMAP(0x1f, 0x1f), /* 0x10: MBOX_INIT_REQ_QUEUE */
ISPOPMAP(0x3f, 0x3f), /* 0x11: MBOX_INIT_RES_QUEUE */
ISPOPMAP(0x0f, 0x0f), /* 0x12: MBOX_EXECUTE_IOCB */
ISPOPMAP(0x03, 0x03), /* 0x13: MBOX_WAKE_UP */
ISPOPMAP(0x01, 0x3f), /* 0x14: MBOX_STOP_FIRMWARE */
ISPOPMAP(0x0f, 0x0f), /* 0x15: MBOX_ABORT */
ISPOPMAP(0x03, 0x03), /* 0x16: MBOX_ABORT_DEVICE */
ISPOPMAP(0x07, 0x07), /* 0x17: MBOX_ABORT_TARGET */
ISPOPMAP(0x07, 0x07), /* 0x18: MBOX_BUS_RESET */
ISPOPMAP(0x03, 0x07), /* 0x19: MBOX_STOP_QUEUE */
ISPOPMAP(0x03, 0x07), /* 0x1a: MBOX_START_QUEUE */
ISPOPMAP(0x03, 0x07), /* 0x1b: MBOX_SINGLE_STEP_QUEUE */
ISPOPMAP(0x03, 0x07), /* 0x1c: MBOX_ABORT_QUEUE */
ISPOPMAP(0x03, 0x4f), /* 0x1d: MBOX_GET_DEV_QUEUE_STATUS */
ISPOPMAP(0x00, 0x00), /* 0x1e: */
ISPOPMAP(0x01, 0x07), /* 0x1f: MBOX_GET_FIRMWARE_STATUS */
ISPOPMAP(0x01, 0x07), /* 0x20: MBOX_GET_INIT_SCSI_ID */
ISPOPMAP(0x01, 0x07), /* 0x21: MBOX_GET_SELECT_TIMEOUT */
ISPOPMAP(0x01, 0xc7), /* 0x22: MBOX_GET_RETRY_COUNT */
ISPOPMAP(0x01, 0x07), /* 0x23: MBOX_GET_TAG_AGE_LIMIT */
ISPOPMAP(0x01, 0x03), /* 0x24: MBOX_GET_CLOCK_RATE */
ISPOPMAP(0x01, 0x07), /* 0x25: MBOX_GET_ACT_NEG_STATE */
ISPOPMAP(0x01, 0x07), /* 0x26: MBOX_GET_ASYNC_DATA_SETUP_TIME */
ISPOPMAP(0x01, 0x07), /* 0x27: MBOX_GET_PCI_PARAMS */
ISPOPMAP(0x03, 0x4f), /* 0x28: MBOX_GET_TARGET_PARAMS */
ISPOPMAP(0x03, 0x0f), /* 0x29: MBOX_GET_DEV_QUEUE_PARAMS */
ISPOPMAP(0x01, 0x07), /* 0x2a: MBOX_GET_RESET_DELAY_PARAMS */
ISPOPMAP(0x00, 0x00), /* 0x2b: */
ISPOPMAP(0x00, 0x00), /* 0x2c: */
ISPOPMAP(0x00, 0x00), /* 0x2d: */
ISPOPMAP(0x00, 0x00), /* 0x2e: */
ISPOPMAP(0x00, 0x00), /* 0x2f: */
ISPOPMAP(0x03, 0x03), /* 0x30: MBOX_SET_INIT_SCSI_ID */
ISPOPMAP(0x07, 0x07), /* 0x31: MBOX_SET_SELECT_TIMEOUT */
ISPOPMAP(0xc7, 0xc7), /* 0x32: MBOX_SET_RETRY_COUNT */
ISPOPMAP(0x07, 0x07), /* 0x33: MBOX_SET_TAG_AGE_LIMIT */
ISPOPMAP(0x03, 0x03), /* 0x34: MBOX_SET_CLOCK_RATE */
ISPOPMAP(0x07, 0x07), /* 0x35: MBOX_SET_ACT_NEG_STATE */
ISPOPMAP(0x07, 0x07), /* 0x36: MBOX_SET_ASYNC_DATA_SETUP_TIME */
ISPOPMAP(0x07, 0x07), /* 0x37: MBOX_SET_PCI_CONTROL_PARAMS */
ISPOPMAP(0x4f, 0x4f), /* 0x38: MBOX_SET_TARGET_PARAMS */
ISPOPMAP(0x0f, 0x0f), /* 0x39: MBOX_SET_DEV_QUEUE_PARAMS */
ISPOPMAP(0x07, 0x07), /* 0x3a: MBOX_SET_RESET_DELAY_PARAMS */
ISPOPMAP(0x00, 0x00), /* 0x3b: */
ISPOPMAP(0x00, 0x00), /* 0x3c: */
ISPOPMAP(0x00, 0x00), /* 0x3d: */
ISPOPMAP(0x00, 0x00), /* 0x3e: */
ISPOPMAP(0x00, 0x00), /* 0x3f: */
ISPOPMAP(0x01, 0x03), /* 0x40: MBOX_RETURN_BIOS_BLOCK_ADDR */
ISPOPMAP(0x3f, 0x01), /* 0x41: MBOX_WRITE_FOUR_RAM_WORDS */
ISPOPMAP(0x03, 0x07), /* 0x42: MBOX_EXEC_BIOS_IOCB */
ISPOPMAP(0x00, 0x00), /* 0x43: */
ISPOPMAP(0x00, 0x00), /* 0x44: */
ISPOPMAP(0x03, 0x03), /* 0x45: SET SYSTEM PARAMETER */
ISPOPMAP(0x01, 0x03), /* 0x46: GET SYSTEM PARAMETER */
ISPOPMAP(0x00, 0x00), /* 0x47: */
ISPOPMAP(0x01, 0xcf), /* 0x48: GET SCAM CONFIGURATION */
ISPOPMAP(0xcf, 0xcf), /* 0x49: SET SCAM CONFIGURATION */
ISPOPMAP(0x03, 0x03), /* 0x4a: MBOX_SET_FIRMWARE_FEATURES */
ISPOPMAP(0x01, 0x03), /* 0x4b: MBOX_GET_FIRMWARE_FEATURES */
ISPOPMAP(0x00, 0x00), /* 0x4c: */
ISPOPMAP(0x00, 0x00), /* 0x4d: */
ISPOPMAP(0x00, 0x00), /* 0x4e: */
ISPOPMAP(0x00, 0x00), /* 0x4f: */
ISPOPMAP(0xdf, 0xdf), /* 0x50: LOAD RAM A64 */
ISPOPMAP(0xdf, 0xdf), /* 0x51: DUMP RAM A64 */
ISPOPMAP(0xdf, 0xdf), /* 0x52: INITIALIZE REQUEST QUEUE A64 */
ISPOPMAP(0xff, 0xff), /* 0x53: INITIALIZE RESPONSE QUEUE A64 */
ISPOPMAP(0xcf, 0xff), /* 0x54: EXECUTE IOCB A64 */
ISPOPMAP(0x03, 0x01), /* 0x55: ENABLE TARGET MODE */
ISPOPMAP(0x00, 0x00), /* 0x56: */
ISPOPMAP(0x00, 0x00), /* 0x57: */
ISPOPMAP(0x00, 0x00), /* 0x58: */
ISPOPMAP(0x00, 0x00), /* 0x59: */
ISPOPMAP(0x03, 0x03), /* 0x5a: SET DATA OVERRUN RECOVERY MODE */
ISPOPMAP(0x01, 0x03), /* 0x5b: GET DATA OVERRUN RECOVERY MODE */
ISPOPMAP(0x0f, 0x0f), /* 0x5c: SET HOST DATA */
ISPOPMAP(0x01, 0x01) /* 0x5d: GET NOST DATA */
};
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
#ifndef ISP_STRIPEED
static char *scsi_mbcmd_names[] = {
"NO-OP",
"LOAD RAM",
"EXEC FIRMWARE",
"DUMP RAM",
"WRITE RAM WORD",
"READ RAM WORD",
"MAILBOX REG TEST",
"VERIFY CHECKSUM",
"ABOUT FIRMWARE",
NULL,
NULL,
NULL,
NULL,
NULL,
"CHECK FIRMWARE",
NULL,
"INIT REQUEST QUEUE",
"INIT RESULT QUEUE",
"EXECUTE IOCB",
"WAKE UP",
"STOP FIRMWARE",
"ABORT",
"ABORT DEVICE",
"ABORT TARGET",
"BUS RESET",
"STOP QUEUE",
"START QUEUE",
"SINGLE STEP QUEUE",
"ABORT QUEUE",
"GET DEV QUEUE STATUS",
NULL,
"GET FIRMWARE STATUS",
"GET INIT SCSI ID",
"GET SELECT TIMEOUT",
"GET RETRY COUNT",
"GET TAG AGE LIMIT",
"GET CLOCK RATE",
"GET ACT NEG STATE",
"GET ASYNC DATA SETUP TIME",
"GET PCI PARAMS",
"GET TARGET PARAMS",
"GET DEV QUEUE PARAMS",
"GET RESET DELAY PARAMS",
NULL,
NULL,
NULL,
NULL,
NULL,
"SET INIT SCSI ID",
"SET SELECT TIMEOUT",
"SET RETRY COUNT",
"SET TAG AGE LIMIT",
"SET CLOCK RATE",
"SET ACT NEG STATE",
"SET ASYNC DATA SETUP TIME",
"SET PCI CONTROL PARAMS",
"SET TARGET PARAMS",
"SET DEV QUEUE PARAMS",
"SET RESET DELAY PARAMS",
NULL,
NULL,
NULL,
NULL,
NULL,
"RETURN BIOS BLOCK ADDR",
"WRITE FOUR RAM WORDS",
"EXEC BIOS IOCB",
NULL,
NULL,
"SET SYSTEM PARAMETER",
"GET SYSTEM PARAMETER",
NULL,
"GET SCAM CONFIGURATION",
"SET SCAM CONFIGURATION",
"SET FIRMWARE FEATURES",
"GET FIRMWARE FEATURES",
NULL,
NULL,
NULL,
NULL,
"LOAD RAM A64",
"DUMP RAM A64",
"INITIALIZE REQUEST QUEUE A64",
"INITIALIZE RESPONSE QUEUE A64",
"EXECUTE IOCB A64",
"ENABLE TARGET MODE",
NULL,
NULL,
NULL,
NULL,
"SET DATA OVERRUN RECOVERY MODE",
"GET DATA OVERRUN RECOVERY MODE",
"SET HOST DATA",
"GET NOST DATA",
};
#endif
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
static u_int16_t mbpfc[] = {
ISPOPMAP(0x01, 0x01), /* 0x00: MBOX_NO_OP */
ISPOPMAP(0x1f, 0x01), /* 0x01: MBOX_LOAD_RAM */
ISPOPMAP(0x03, 0x01), /* 0x02: MBOX_EXEC_FIRMWARE */
ISPOPMAP(0x1f, 0x01), /* 0x03: MBOX_DUMP_RAM */
ISPOPMAP(0x07, 0x07), /* 0x04: MBOX_WRITE_RAM_WORD */
ISPOPMAP(0x03, 0x07), /* 0x05: MBOX_READ_RAM_WORD */
ISPOPMAP(0xff, 0xff), /* 0x06: MBOX_MAILBOX_REG_TEST */
ISPOPMAP(0x03, 0x05), /* 0x07: MBOX_VERIFY_CHECKSUM */
ISPOPMAP(0x01, 0x0f), /* 0x08: MBOX_ABOUT_FIRMWARE */
ISPOPMAP(0xdf, 0x01), /* 0x09: LOAD RAM */
ISPOPMAP(0xdf, 0x01), /* 0x0a: DUMP RAM */
ISPOPMAP(0x00, 0x00), /* 0x0b: */
ISPOPMAP(0x00, 0x00), /* 0x0c: */
ISPOPMAP(0x00, 0x00), /* 0x0d: */
ISPOPMAP(0x01, 0x05), /* 0x0e: MBOX_CHECK_FIRMWARE */
ISPOPMAP(0x00, 0x00), /* 0x0f: */
ISPOPMAP(0x1f, 0x11), /* 0x10: MBOX_INIT_REQ_QUEUE */
ISPOPMAP(0x2f, 0x21), /* 0x11: MBOX_INIT_RES_QUEUE */
ISPOPMAP(0x0f, 0x01), /* 0x12: MBOX_EXECUTE_IOCB */
ISPOPMAP(0x03, 0x03), /* 0x13: MBOX_WAKE_UP */
ISPOPMAP(0x01, 0xff), /* 0x14: MBOX_STOP_FIRMWARE */
ISPOPMAP(0x4f, 0x01), /* 0x15: MBOX_ABORT */
ISPOPMAP(0x07, 0x01), /* 0x16: MBOX_ABORT_DEVICE */
ISPOPMAP(0x07, 0x01), /* 0x17: MBOX_ABORT_TARGET */
ISPOPMAP(0x03, 0x03), /* 0x18: MBOX_BUS_RESET */
ISPOPMAP(0x07, 0x05), /* 0x19: MBOX_STOP_QUEUE */
ISPOPMAP(0x07, 0x05), /* 0x1a: MBOX_START_QUEUE */
ISPOPMAP(0x07, 0x05), /* 0x1b: MBOX_SINGLE_STEP_QUEUE */
ISPOPMAP(0x07, 0x05), /* 0x1c: MBOX_ABORT_QUEUE */
ISPOPMAP(0x07, 0x03), /* 0x1d: MBOX_GET_DEV_QUEUE_STATUS */
ISPOPMAP(0x00, 0x00), /* 0x1e: */
ISPOPMAP(0x01, 0x07), /* 0x1f: MBOX_GET_FIRMWARE_STATUS */
ISPOPMAP(0x01, 0x4f), /* 0x20: MBOX_GET_LOOP_ID */
ISPOPMAP(0x00, 0x00), /* 0x21: */
ISPOPMAP(0x01, 0x07), /* 0x22: MBOX_GET_RETRY_COUNT */
ISPOPMAP(0x00, 0x00), /* 0x23: */
ISPOPMAP(0x00, 0x00), /* 0x24: */
ISPOPMAP(0x00, 0x00), /* 0x25: */
ISPOPMAP(0x00, 0x00), /* 0x26: */
ISPOPMAP(0x00, 0x00), /* 0x27: */
ISPOPMAP(0x0f, 0x1), /* 0x28: MBOX_GET_FIRMWARE_OPTIONS */
ISPOPMAP(0x03, 0x07), /* 0x29: MBOX_GET_PORT_QUEUE_PARAMS */
ISPOPMAP(0x00, 0x00), /* 0x2a: */
ISPOPMAP(0x00, 0x00), /* 0x2b: */
ISPOPMAP(0x00, 0x00), /* 0x2c: */
ISPOPMAP(0x00, 0x00), /* 0x2d: */
ISPOPMAP(0x00, 0x00), /* 0x2e: */
ISPOPMAP(0x00, 0x00), /* 0x2f: */
ISPOPMAP(0x00, 0x00), /* 0x30: */
ISPOPMAP(0x00, 0x00), /* 0x31: */
ISPOPMAP(0x07, 0x07), /* 0x32: MBOX_SET_RETRY_COUNT */
ISPOPMAP(0x00, 0x00), /* 0x33: */
ISPOPMAP(0x00, 0x00), /* 0x34: */
ISPOPMAP(0x00, 0x00), /* 0x35: */
ISPOPMAP(0x00, 0x00), /* 0x36: */
ISPOPMAP(0x00, 0x00), /* 0x37: */
ISPOPMAP(0x0f, 0x01), /* 0x38: MBOX_SET_FIRMWARE_OPTIONS */
ISPOPMAP(0x0f, 0x07), /* 0x39: MBOX_SET_PORT_QUEUE_PARAMS */
ISPOPMAP(0x00, 0x00), /* 0x3a: */
ISPOPMAP(0x00, 0x00), /* 0x3b: */
ISPOPMAP(0x00, 0x00), /* 0x3c: */
ISPOPMAP(0x00, 0x00), /* 0x3d: */
ISPOPMAP(0x00, 0x00), /* 0x3e: */
ISPOPMAP(0x00, 0x00), /* 0x3f: */
ISPOPMAP(0x03, 0x01), /* 0x40: MBOX_LOOP_PORT_BYPASS */
ISPOPMAP(0x03, 0x01), /* 0x41: MBOX_LOOP_PORT_ENABLE */
ISPOPMAP(0x03, 0x07), /* 0x42: MBOX_GET_RESOURCE_COUNTS */
ISPOPMAP(0x01, 0x01), /* 0x43: MBOX_REQUEST_NON_PARTICIPATING_MODE */
ISPOPMAP(0x00, 0x00), /* 0x44: */
ISPOPMAP(0x00, 0x00), /* 0x45: */
ISPOPMAP(0x00, 0x00), /* 0x46: */
ISPOPMAP(0xcf, 0x03), /* 0x47: GET PORT_DATABASE ENHANCED */
ISPOPMAP(0x00, 0x00), /* 0x48: */
ISPOPMAP(0x00, 0x00), /* 0x49: */
ISPOPMAP(0x00, 0x00), /* 0x4a: */
ISPOPMAP(0x00, 0x00), /* 0x4b: */
ISPOPMAP(0x00, 0x00), /* 0x4c: */
ISPOPMAP(0x00, 0x00), /* 0x4d: */
ISPOPMAP(0x00, 0x00), /* 0x4e: */
ISPOPMAP(0x00, 0x00), /* 0x4f: */
ISPOPMAP(0x00, 0x00), /* 0x50: */
ISPOPMAP(0x00, 0x00), /* 0x51: */
ISPOPMAP(0x00, 0x00), /* 0x52: */
ISPOPMAP(0x00, 0x00), /* 0x53: */
ISPOPMAP(0xcf, 0x01), /* 0x54: EXECUTE IOCB A64 */
ISPOPMAP(0x00, 0x00), /* 0x55: */
ISPOPMAP(0x00, 0x00), /* 0x56: */
ISPOPMAP(0x00, 0x00), /* 0x57: */
ISPOPMAP(0x00, 0x00), /* 0x58: */
ISPOPMAP(0x00, 0x00), /* 0x59: */
ISPOPMAP(0x00, 0x00), /* 0x5a: */
ISPOPMAP(0x00, 0x00), /* 0x5b: */
ISPOPMAP(0x00, 0x00), /* 0x5c: */
ISPOPMAP(0x00, 0x00), /* 0x5d: */
ISPOPMAP(0x00, 0x00), /* 0x5e: */
ISPOPMAP(0x00, 0x00), /* 0x5f: */
ISPOPMAP(0xfd, 0x31), /* 0x60: MBOX_INIT_FIRMWARE */
ISPOPMAP(0x00, 0x00), /* 0x61: */
ISPOPMAP(0x01, 0x01), /* 0x62: MBOX_INIT_LIP */
ISPOPMAP(0xcd, 0x03), /* 0x63: MBOX_GET_FC_AL_POSITION_MAP */
ISPOPMAP(0xcf, 0x01), /* 0x64: MBOX_GET_PORT_DB */
ISPOPMAP(0x07, 0x01), /* 0x65: MBOX_CLEAR_ACA */
ISPOPMAP(0x07, 0x01), /* 0x66: MBOX_TARGET_RESET */
ISPOPMAP(0x07, 0x01), /* 0x67: MBOX_CLEAR_TASK_SET */
ISPOPMAP(0x07, 0x01), /* 0x68: MBOX_ABORT_TASK_SET */
ISPOPMAP(0x01, 0x07), /* 0x69: MBOX_GET_FW_STATE */
ISPOPMAP(0x03, 0xcf), /* 0x6a: MBOX_GET_PORT_NAME */
ISPOPMAP(0xcf, 0x01), /* 0x6b: MBOX_GET_LINK_STATUS */
ISPOPMAP(0x0f, 0x01), /* 0x6c: MBOX_INIT_LIP_RESET */
ISPOPMAP(0x00, 0x00), /* 0x6d: */
ISPOPMAP(0xcf, 0x03), /* 0x6e: MBOX_SEND_SNS */
ISPOPMAP(0x0f, 0x07), /* 0x6f: MBOX_FABRIC_LOGIN */
ISPOPMAP(0x03, 0x01), /* 0x70: MBOX_SEND_CHANGE_REQUEST */
ISPOPMAP(0x03, 0x03), /* 0x71: MBOX_FABRIC_LOGOUT */
ISPOPMAP(0x0f, 0x0f), /* 0x72: MBOX_INIT_LIP_LOGIN */
ISPOPMAP(0x00, 0x00), /* 0x73: */
ISPOPMAP(0x07, 0x01), /* 0x74: LOGIN LOOP PORT */
ISPOPMAP(0xcf, 0x03), /* 0x75: GET PORT/NODE NAME LIST */
ISPOPMAP(0x4f, 0x01), /* 0x76: SET VENDOR ID */
ISPOPMAP(0xcd, 0x01), /* 0x77: INITIALIZE IP MAILBOX */
ISPOPMAP(0x00, 0x00), /* 0x78: */
ISPOPMAP(0x00, 0x00), /* 0x79: */
ISPOPMAP(0x00, 0x00), /* 0x7a: */
ISPOPMAP(0x00, 0x00), /* 0x7b: */
ISPOPMAP(0x4f, 0x03), /* 0x7c: Get ID List */
ISPOPMAP(0xcf, 0x01), /* 0x7d: SEND LFA */
ISPOPMAP(0x07, 0x01) /* 0x7e: Lun RESET */
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
};
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
#ifndef ISP_STRIPPED
static char *fc_mbcmd_names[] = {
"NO-OP",
"LOAD RAM",
"EXEC FIRMWARE",
"DUMP RAM",
"WRITE RAM WORD",
"READ RAM WORD",
"MAILBOX REG TEST",
"VERIFY CHECKSUM",
"ABOUT FIRMWARE",
"LOAD RAM",
"DUMP RAM",
NULL,
NULL,
NULL,
"CHECK FIRMWARE",
NULL,
"INIT REQUEST QUEUE",
"INIT RESULT QUEUE",
"EXECUTE IOCB",
"WAKE UP",
"STOP FIRMWARE",
"ABORT",
"ABORT DEVICE",
"ABORT TARGET",
"BUS RESET",
"STOP QUEUE",
"START QUEUE",
"SINGLE STEP QUEUE",
"ABORT QUEUE",
"GET DEV QUEUE STATUS",
NULL,
"GET FIRMWARE STATUS",
"GET LOOP ID",
NULL,
"GET RETRY COUNT",
NULL,
NULL,
NULL,
NULL,
NULL,
"GET FIRMWARE OPTIONS",
"GET PORT QUEUE PARAMS",
NULL,
NULL,
NULL,
NULL,
NULL,
NULL,
NULL,
NULL,
"SET RETRY COUNT",
NULL,
NULL,
NULL,
NULL,
NULL,
"SET FIRMWARE OPTIONS",
"SET PORT QUEUE PARAMS",
NULL,
NULL,
NULL,
NULL,
NULL,
NULL,
"LOOP PORT BYPASS",
"LOOP PORT ENABLE",
"GET RESOURCE COUNTS",
"REQUEST NON PARTICIPATING MODE",
NULL,
NULL,
NULL,
"GET PORT DATABASE,, ENHANCED",
NULL,
NULL,
NULL,
NULL,
NULL,
NULL,
NULL,
NULL,
NULL,
NULL,
NULL,
NULL,
"EXECUTE IOCB A64",
NULL,
NULL,
NULL,
NULL,
NULL,
NULL,
NULL,
NULL,
NULL,
NULL,
NULL,
"INIT FIRMWARE",
NULL,
"INIT LIP",
"GET FC-AL POSITION MAP",
"GET PORT DATABASE",
"CLEAR ACA",
"TARGET RESET",
"CLEAR TASK SET",
"ABORT TASK SET",
"GET FW STATE",
"GET PORT NAME",
"GET LINK STATUS",
"INIT LIP RESET",
NULL,
"SEND SNS",
"FABRIC LOGIN",
"SEND CHANGE REQUEST",
"FABRIC LOGOUT",
"INIT LIP LOGIN",
NULL,
"LOGIN LOOP PORT",
"GET PORT/NODE NAME LIST",
"SET VENDOR ID",
"INITIALIZE IP MAILBOX",
NULL,
NULL,
NULL,
NULL,
"Get ID List",
"SEND LFA",
"Lun RESET"
};
#endif
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
static void
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, mbp, logmask)
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
struct ispsoftc *isp;
mbreg_t *mbp;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
int logmask;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
{
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
char *cname, *xname, tname[16], mname[16];
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
unsigned int lim, ibits, obits, box, opcode;
u_int16_t *mcp;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
if (IS_FC(isp)) {
mcp = mbpfc;
lim = (sizeof (mbpfc) / sizeof (mbpfc[0]));
} else {
mcp = mbpscsi;
lim = (sizeof (mbpscsi) / sizeof (mbpscsi[0]));
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
if ((opcode = mbp->param[0]) >= lim) {
mbp->param[0] = MBOX_INVALID_COMMAND;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR, "Unknown Command 0x%x", opcode);
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
return;
Remove the Target mode functions until they're in better shape. Implement some suggested compilation cleanups from Eklund. Wire down a hard loop id if we are not on a platform that has the ability to get to a PCI BIOS (it still will float to the ID it gets after a LIP but at least we can try). Clarify that the expanded lun is based upon SCCLUN defines (in f/w).
1998-12-05 01:33:57 +00:00
}
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
ibits = HIBYT(mcp[opcode]) & NMBOX_BMASK(isp);
obits = LOBYT(mcp[opcode]) & NMBOX_BMASK(isp);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
if (ibits == 0 && obits == 0) {
mbp->param[0] = MBOX_COMMAND_PARAM_ERROR;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR, "no parameters for 0x%x", opcode);
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
return;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
/*
* Get exclusive usage of mailbox registers.
*/
MBOX_ACQUIRE(isp);
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
for (box = 0; box < MAX_MAILBOX; box++) {
if (ibits & (1 << box)) {
ISP_WRITE(isp, MBOX_OFF(box), mbp->param[box]);
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
}
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
isp->isp_mboxtmp[box] = mbp->param[box] = 0;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
/*
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
* We assume that we can't overwrite a previous command.
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
*/
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
isp->isp_mboxbsy = obits;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
/*
* Set Host Interrupt condition so that RISC will pick up mailbox regs.
*/
ISP_WRITE(isp, HCCR, HCCR_CMD_SET_HOST_INT);
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
/*
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
* Give the f/w a chance to pick this up.
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
*/
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
USEC_DELAY(250);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
/*
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
* While we haven't finished the command, spin our wheels here.
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
*/
Change delay loop in new isp_mboxcmd to the use of the new MBOX_WAIT_COMPLETE macro. Change notification of completion of a mailbox command in isp_intr to MBOX_NOTIFY_COMPLETE macro.
2000-07-04 01:02:38 +00:00
MBOX_WAIT_COMPLETE(isp);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
/*
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
* Copy back output registers.
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
*/
Fix usage of DELAY (SYS_DELAY is the platform independent local define). Fix stupidity wrt checking whether we've gone to LOOP_PDB_RCVD loopstate- it's okay to be greater than this state. D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC macros. Completely redo mailbox command routine (in preparation to make this possibly wait rather than poll for completion). Make a major attempt to solve the 'lost interrupt' problem 1. Problem The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate regular SCSI command placed on the request queue would never complete and the watchdog routine in the driver would eventually wakeup and catch it. This would typically only happen on Alphas, although a couple folks with 700MHz Intel platforms have also seen this. For a long time I thought it was a foulup with f/w negotiations of SYNC and/or WIDE as it always seemed to happen right after the platform it was running on had done a SET TARGET PARAMETERS mailbox command to (re)enable sync && wide (after initially forcing ASYNC/NARROW at startup). However, occasionally, the same thing would also occur for the Fibre Channel cards as well (which, ahem, have no SET TARGET PARAMETERS for transfer mode). After finally putting in a better set of watchdog routines for the platforms for this driver, it seemed to be the case that the command in question (usually a READ CAPACITY) just had up and died- the watchdog routine would catch it after ~10 seconds. For some platforms (NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which would always fail- indicating that the f/w denied knowledge of this command, i.e., the f/w thought it was a done command). In any case, retrying the command worked. But this whole problem needed to be really fixed. 2. A False Step That Went in The Right Direction The mailbox code was completely rewritten to no longer try and grab the mailbox semaphore register and to try and 'by hand' complete async fast posting completions. It was also rewritten to now have separate in && out bitpatterns for registers to load to start and retrieve to complete. This means that isp_intr now handles mailbox completions. This substantially simplifies the mailbox handling code, and carries things 90% toward getting this to be a non-polled routine for this driver. This did not solve the problem, though. 3. Register Debouncing I saw some comments in some errata sheets and some notes in a Qlogic produced Linux driver (for the Qlogic 2100) that seemed to indicate that debouncing of reads of the mailbox registers might be needed, so I added this. This did not affect the problem. In fact, it made the problem worse for non-2100 cards. 5. Interrupt masking/unmasking The driver *used* to do a substantial amount of masking/unmasking of the interrupt control register. This was done to make sure that the core common code could just assume it would never get pre-empted. This apparently substantially contributed to the lost interrupt problem. The rewrite of the ICR (Interrupt Control Register), which is a separate register from the ISR (Interrupt Status Register) should not have caused any change to interrupt assertions pending. The manual does not state that it will, and the register layout seems to imply that the ICR is just an active route gate. We only enable PCI Interrupts and RISC Interrupts- this should mean that when the f/w asserts a RISC interrupt and (and the ICR allows RISC Interrupts) and we have PCI Interrupts enabled, we should get a PCI interrupt. Apparently this is a latch- not a signal route. Removing this got rid of *most* but not all, lost interrupts. 5. Watchdog Smartening I made sure that the watchdog routine would catch cases where the Qlogic's ISR showed an interrupt assertion. The watchdog routine now calls the interrupt service routine if it sees this. Some additional internal state flags were added so that the watchdog routine could then know whether the command it was in the middle of burying (because we had time it out) was in fact completed by the interrupt service routine. 6. Occasional Constipation Of Commands.. In running some very strenous high IOPs tests (generating about 11000 interrupts/second across one Qlogic 1040, one Qlogic 1080 and one Qlogic 2200 on an Alpha PC164), I found that I would get occasional but regular 'watchdog timeouts' on both the 1080 and the 2100 cards. This is under FreeBSD, and the watchdog timeout routine just marks the command in error and retries it. Invariably, right after this 'watchdog timeout' error, I'd get a command completion for the command that I had thought timed out. That is, I'd get a command completion, but the handle returned by the firmware mapped to no current command. The frequency of this problem is low under such a load- it would usually take an 30 minutes per 'lost' interrupt. I doubled the timeout for commands to see if it just was an edge case of waiting too short a period. This has no effect. I gathered and printed out microtimes for the watchdog completed command and the completion that couldn't find a command- it was always the case that the order of occurrence was "timeout, completion" separated by a time on the order of 100 to 150 ms. This caused me to consider 'firmware constipation' as to be a possible culprit. That is, resubmission of a command to the device that had suffered a watchdog timeout seemed to cause the presumed dead command to show back up. I added code in the watchdog routine that, when first entered for the command, marks the command with a flag, reissues a local timeout call for one second later, but also then issues a MARKER Request Queue entry to the Qlogic f/w. A MARKER entry is used typically after a Bus Reset to cause the f/w to get synchronized with respect to either a Bus, a Nexus or a Target. Since I've added this code, I always now see the occasional watchdog timeout, but the command that was about to be terminated always now seems to be completed after the MARKER entry is issued (and before the timeout extension fires, which would come back and *really* terminate the command).
2000-06-27 19:44:31 +00:00
for (box = 0; box < MAX_MAILBOX; box++) {
if (obits & (1 << box)) {
mbp->param[box] = isp->isp_mboxtmp[box];
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
}
}
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
MBOX_RELEASE(isp);
if (logmask == 0 || opcode == MBOX_EXEC_FIRMWARE) {
return;
}
#ifdef ISP_STRIPPED
cname = NULL;
#else
cname = (IS_FC(isp))? fc_mbcmd_names[opcode] : scsi_mbcmd_names[opcode];
#endif
if (cname == NULL) {
SNPRINTF(cname, sizeof tname, "opcode %x", opcode);
}
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
/*
* Just to be chatty here...
*/
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
xname = NULL;
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
switch (mbp->param[0]) {
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
case MBOX_COMMAND_COMPLETE:
break;
case MBOX_INVALID_COMMAND:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
if (logmask & MBLOGMASK(MBOX_COMMAND_COMPLETE))
xname = "INVALID COMMAND";
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
break;
case MBOX_HOST_INTERFACE_ERROR:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
if (logmask & MBLOGMASK(MBOX_HOST_INTERFACE_ERROR))
xname = "HOST INTERFACE ERROR";
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
break;
case MBOX_TEST_FAILED:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
if (logmask & MBLOGMASK(MBOX_TEST_FAILED))
xname = "TEST FAILED";
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
break;
case MBOX_COMMAND_ERROR:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
if (logmask & MBLOGMASK(MBOX_COMMAND_ERROR))
xname = "COMMAND ERROR";
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
break;
case MBOX_COMMAND_PARAM_ERROR:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
if (logmask & MBLOGMASK(MBOX_COMMAND_PARAM_ERROR))
xname = "COMMAND PARAMETER ERROR";
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
break;
Slightly cleaner fabric support (whiter whites! redder reds!).. No, seriously- only attempt to logout a previously logged in fabric device. Fix a longstanding bug for aborting overtime commands- handle halves have always been reversed. Clean up some error messages to indicate channel number. Approved:jkh
2000-02-29 05:52:14 +00:00
case MBOX_LOOP_ID_USED:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
if (logmask & MBLOGMASK(MBOX_LOOP_ID_USED))
xname = "LOOP ID ALREADY IN USE";
break;
Slightly cleaner fabric support (whiter whites! redder reds!).. No, seriously- only attempt to logout a previously logged in fabric device. Fix a longstanding bug for aborting overtime commands- handle halves have always been reversed. Clean up some error messages to indicate channel number. Approved:jkh
2000-02-29 05:52:14 +00:00
case MBOX_PORT_ID_USED:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
if (logmask & MBLOGMASK(MBOX_PORT_ID_USED))
xname = "PORT ID ALREADY IN USE";
break;
Slightly cleaner fabric support (whiter whites! redder reds!).. No, seriously- only attempt to logout a previously logged in fabric device. Fix a longstanding bug for aborting overtime commands- handle halves have always been reversed. Clean up some error messages to indicate channel number. Approved:jkh
2000-02-29 05:52:14 +00:00
case MBOX_ALL_IDS_USED:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
if (logmask & MBLOGMASK(MBOX_ALL_IDS_USED))
xname = "ALL LOOP IDS IN USE";
break;
case 0: /* special case */
xname = "TIMEOUT";
Slightly cleaner fabric support (whiter whites! redder reds!).. No, seriously- only attempt to logout a previously logged in fabric device. Fix a longstanding bug for aborting overtime commands- handle halves have always been reversed. Clean up some error messages to indicate channel number. Approved:jkh
2000-02-29 05:52:14 +00:00
break;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
default:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
SNPRINTF(mname, sizeof mname, "error 0x%x", mbp->param[0]);
xname = mname;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
break;
}
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
if (xname)
isp_prt(isp, ISP_LOGALL, "Mailbox Command '%s' failed (%s)",
cname, xname);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
static void
isp_fw_state(isp)
struct ispsoftc *isp;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
{
More code cleanup. Go back to using FULL_LOGIN Fibre Chan if f/w is less than 1.17.0 level. Change where we do the loop database init. Add in the CMD_RQLATER return. Add some register debounce.
1999-08-16 19:59:55 +00:00
if (IS_FC(isp)) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
mbreg_t mbs;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
fcparam *fcp = isp->isp_param;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
mbs.param[0] = MBOX_GET_FW_STATE;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGALL);
if (mbs.param[0] == MBOX_COMMAND_COMPLETE)
fcp->isp_fwstate = mbs.param[1];
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
}
static void
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
isp_update(isp)
struct ispsoftc *isp;
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
{
various fixes
2000-08-27 23:38:44 +00:00
int bus, upmask;
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
various fixes
2000-08-27 23:38:44 +00:00
for (bus = 0, upmask = isp->isp_update; upmask != 0; bus++) {
if (upmask & (1 << bus)) {
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
isp_update_bus(isp, bus);
}
various fixes
2000-08-27 23:38:44 +00:00
upmask &= ~(1 << bus);
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
}
}
static void
isp_update_bus(isp, bus)
struct ispsoftc *isp;
int bus;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
{
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
int tgt;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
mbreg_t mbs;
sdparam *sdp;
various fixes
2000-08-27 23:38:44 +00:00
isp->isp_update &= ~(1 << bus);
More code cleanup. Go back to using FULL_LOGIN Fibre Chan if f/w is less than 1.17.0 level. Change where we do the loop database init. Add in the CMD_RQLATER return. Add some register debounce.
1999-08-16 19:59:55 +00:00
if (IS_FC(isp)) {
various fixes
2000-08-27 23:38:44 +00:00
/*
* There are no 'per-bus' settings for Fibre Channel.
*/
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
return;
}
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
sdp = isp->isp_param;
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
sdp += bus;
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
for (tgt = 0; tgt < MAX_TARGETS; tgt++) {
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
u_int16_t flags, period, offset;
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
int get;
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
if (sdp->isp_devparam[tgt].dev_enable == 0) {
various fixes
2000-08-27 23:38:44 +00:00
sdp->isp_devparam[tgt].dev_update = 0;
sdp->isp_devparam[tgt].dev_refresh = 0;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGDEBUG1,
"skipping target %d bus %d update", tgt, bus);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
continue;
}
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
/*
* If the goal is to update the status of the device,
* take what's in dev_flags and try and set the device
* toward that. Otherwise, if we're just refreshing the
* current device state, get the current parameters.
*/
various fixes
2000-08-27 23:38:44 +00:00
/*
* Refresh overrides set
*/
if (sdp->isp_devparam[tgt].dev_refresh) {
mbs.param[0] = MBOX_GET_TARGET_PARAMS;
sdp->isp_devparam[tgt].dev_refresh = 0;
get = 1;
} else if (sdp->isp_devparam[tgt].dev_update) {
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
mbs.param[0] = MBOX_SET_TARGET_PARAMS;
various fixes
2000-08-27 23:38:44 +00:00
/*
* Make sure dev_flags has "Renegotiate on Error"
* on and "Freeze Queue on Error" off.
*/
sdp->isp_devparam[tgt].dev_flags |= DPARM_RENEG;
sdp->isp_devparam[tgt].dev_flags &= ~DPARM_QFRZ;
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
mbs.param[2] = sdp->isp_devparam[tgt].dev_flags;
various fixes
2000-08-27 23:38:44 +00:00
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
/*
various fixes
2000-08-27 23:38:44 +00:00
* Insist that PARITY must be enabled
* if SYNC or WIDE is enabled.
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
*/
various fixes
2000-08-27 23:38:44 +00:00
if ((mbs.param[2] & (DPARM_SYNC|DPARM_WIDE)) != 0) {
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
mbs.param[2] |= DPARM_PARITY;
}
various fixes
2000-08-27 23:38:44 +00:00
if ((mbs.param[2] & DPARM_SYNC) == 0) {
mbs.param[3] = 0;
} else {
mbs.param[3] =
(sdp->isp_devparam[tgt].sync_offset << 8) |
(sdp->isp_devparam[tgt].sync_period);
}
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
/*
* A command completion later that has
various fixes
2000-08-27 23:38:44 +00:00
* RQSTF_NEGOTIATION set canl cause
* the dev_refresh/announce cycle also.
&
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
*
* Note: It is really important to update our current
* flags with at least the state of TAG capabilities-
* otherwise we might try and send a tagged command
* when we have it all turned off. So change it here
* to say that current already matches goal.
*/
sdp->isp_devparam[tgt].cur_dflags &= ~DPARM_TQING;
sdp->isp_devparam[tgt].cur_dflags |=
(sdp->isp_devparam[tgt].dev_flags & DPARM_TQING);
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGDEBUG2,
"bus %d set tgt %d flags 0x%x off 0x%x period 0x%x",
bus, tgt, mbs.param[2], mbs.param[3] >> 8,
mbs.param[3] & 0xff);
various fixes
2000-08-27 23:38:44 +00:00
sdp->isp_devparam[tgt].dev_update = 0;
sdp->isp_devparam[tgt].dev_refresh = 1;
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
get = 0;
} else {
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
continue;
}
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
mbs.param[1] = (bus << 15) | (tgt << 8) ;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGALL);
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
if (get == 0) {
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
isp->isp_sendmarker |= (1 << bus);
Implement and use Fast Posting for both parallel && fibre. Redo a bit of the startup code. Implement a call to outer framework function so that asynchronous events can be handled (e.g., speed negotiation, target mode). Roll internal release tags.
1999-01-30 07:29:00 +00:00
continue;
}
flags = mbs.param[2];
period = mbs.param[3] & 0xff;
offset = mbs.param[3] >> 8;
sdp->isp_devparam[tgt].cur_dflags = flags;
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
sdp->isp_devparam[tgt].cur_period = period;
sdp->isp_devparam[tgt].cur_offset = offset;
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
get = (bus << 16) | tgt;
(void) isp_async(isp, ISPASYNC_NEW_TGT_PARAMS, &get);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
various fixes
2000-08-27 23:38:44 +00:00
for (tgt = 0; tgt < MAX_TARGETS; tgt++) {
if (sdp->isp_devparam[tgt].dev_update ||
sdp->isp_devparam[tgt].dev_refresh) {
isp->isp_update |= (1 << bus);
break;
}
}
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
}
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
static void
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
isp_setdfltparm(isp, channel)
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
struct ispsoftc *isp;
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
int channel;
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
{
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
int tgt;
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
mbreg_t mbs;
Clean up some f/w revision checking wrt enabling fast posting. Make sure we set defaults sanely for dual-bus adapters.
1999-12-20 01:34:01 +00:00
sdparam *sdp;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
if (IS_FC(isp)) {
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
fcparam *fcp = (fcparam *) isp->isp_param;
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
fcp += channel;
if (fcp->isp_gotdparms) {
return;
}
fcp->isp_gotdparms = 1;
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
fcp->isp_maxfrmlen = ICB_DFLT_FRMLEN;
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
fcp->isp_maxalloc = ICB_DFLT_ALLOC;
various fixes
2000-08-27 23:38:44 +00:00
fcp->isp_execthrottle = ISP_EXEC_THROTTLE;
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
fcp->isp_retry_delay = ICB_DFLT_RDELAY;
fcp->isp_retry_count = ICB_DFLT_RCOUNT;
/* Platform specific.... */
fcp->isp_loopid = DEFAULT_LOOPID(isp);
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
fcp->isp_nodewwn = DEFAULT_NODEWWN(isp);
fcp->isp_portwwn = DEFAULT_PORTWWN(isp);
various fixes
2000-08-27 23:38:44 +00:00
fcp->isp_fwoptions = 0;
fcp->isp_fwoptions |= ICBOPT_FAIRNESS;
fcp->isp_fwoptions |= ICBOPT_PDBCHANGE_AE;
fcp->isp_fwoptions |= ICBOPT_HARD_ADDRESS;
#ifndef ISP_NO_FASTPOST_FC
fcp->isp_fwoptions |= ICBOPT_FAST_POST;
#endif
if (isp->isp_confopts & ISP_CFG_FULL_DUPLEX)
fcp->isp_fwoptions |= ICBOPT_FULL_DUPLEX;
/*
* Make sure this is turned off now until we get
* extended options from NVRAM
*/
fcp->isp_fwoptions &= ~ICBOPT_EXTENDED;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
/*
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
* Now try and read NVRAM
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
*/
Clean up stupidity in the isp_handle_other_response function- indexes of queue entries have to be at least 16 bits now! If we're running a 2100 less than rev 5, turn off loop fairness (per Qlogic errata). Fix typo in checking against 2200 F/W revision. Slightly fix/reorder fabric login stuff. Change to usage of isp_getrqentry for code clarity. Add some defensive dual bus assumptions. Various cleanups, etc...
1999-11-21 03:18:22 +00:00
if ((isp->isp_confopts & (ISP_CFG_NONVRAM|ISP_CFG_OWNWWN)) ||
(isp_read_nvram(isp))) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGINFO,
"Node WWN 0x%08x%08x, Port WWN 0x%08x%08x",
(u_int32_t) (fcp->isp_nodewwn >> 32),
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
(u_int32_t) (fcp->isp_nodewwn & 0xffffffff),
(u_int32_t) (fcp->isp_portwwn >> 32),
(u_int32_t) (fcp->isp_portwwn & 0xffffffff));
Roll revision levels. Add support for the Qlogic 2200 (warn about not having SCSI_ISP_SCCLUN config defined if we don't have f/w for the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change the way the default LoopID is gathered (it's now a platform specific define so that some attempt at a synthetic WWN can be made in case NVRAM isn't readable). Change initialization of options a bit- don't use ADISC. Set FullDuplex mode if config options tells us to do so. Do not use FULL_LOGIN after LIP- it's the right thing to do but it causes too much loop disruption (Loop Resets). Sanity check some default values. Redo construction of port and node WWNs based upon what we have- if we have 2 in the top nibble, we can have distinct port and node WWNs. Clean up some SCCLUN related code that we obviously had never compiled (:-(). Audit commands coming int ispscsicmd and don't throw commands at Fibre devices that do not have Class 3 service parameters TARGET ROLE defined. Clean up f/w initialization a bit. Add Fabric support (or at least the first blush of it). Whew - way too much to describe here. Basically, after a LIP, hang out until we see a Loop Up or a Port DataBase Change async event, then see if we're on a Fabric (GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric controller for fabric devices using the GetAllNext SNS subcommand. As we find devices, announce them to the outer layer. Try and do some guard code for broken (Brocade) SNS servers (that get stuck in loops- gotta maybe do this a different way using the GP_ID3 cmd instead). Then do a scan of the lower (local loop) ids using a GET_PORT_NAME to see if the f/w has logged into anything at that loop id. If so, then do a GET_PORT_DATABASE command. Do this scan into a local database. At this point we can say the loop is 'Ready'. After this, we merge our local loop port database with our stored port database- in a as yet to be really fully exercised fashion we try and follow the logic of something having moved around. The first time we see something at a Loop ID, we fix it, for the purpose of this system instance, at that Loop ID. If things shift around so it ends up somewhere else, we still keep it at this Loop ID (our 'Target') but use the new (moved) Loop ID when we actually throw commands at it. Check for insane cases of different Loop IDs both claiming to have the same WWN- if that happens, invalidate both. Notify the outer layer of devices that have arrived and devices that have gone away. *Finally*, when this is done, search the softc's database of Fabric devices and perform logout/login actions. The Qlogic f/w maintains logout/login for all local loop devices. We have to maintain logout/login for fabric devices- total PITA. Expect to see this area undergo more change over time.
1999-07-02 23:06:38 +00:00
}
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
return;
}
Clean up some f/w revision checking wrt enabling fast posting. Make sure we set defaults sanely for dual-bus adapters.
1999-12-20 01:34:01 +00:00
sdp = (sdparam *) isp->isp_param;
sdp += channel;
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
/*
* Been there, done that, got the T-shirt...
*/
if (sdp->isp_gotdparms) {
return;
}
sdp->isp_gotdparms = 1;
/*
* If we've not been told to avoid reading NVRAM, try and read it.
* If we're successful reading it, we can return since NVRAM will
* tell us the right thing to do. Otherwise, establish some reasonable
* defaults.
*/
if ((isp->isp_confopts & ISP_CFG_NONVRAM) == 0) {
if (isp_read_nvram(isp) == 0) {
return;
}
}
/*
* Now try and see whether we have specific values for them.
*/
Clean up some f/w revision checking wrt enabling fast posting. Make sure we set defaults sanely for dual-bus adapters.
1999-12-20 01:34:01 +00:00
if ((isp->isp_confopts & ISP_CFG_NONVRAM) == 0) {
mbs.param[0] = MBOX_GET_ACT_NEG_STATE;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGALL);
Clean up some f/w revision checking wrt enabling fast posting. Make sure we set defaults sanely for dual-bus adapters.
1999-12-20 01:34:01 +00:00
if (mbs.param[0] != MBOX_COMMAND_COMPLETE) {
sdp->isp_req_ack_active_neg = 1;
sdp->isp_data_line_active_neg = 1;
} else {
sdp->isp_req_ack_active_neg =
(mbs.param[1+channel] >> 4) & 0x1;
sdp->isp_data_line_active_neg =
(mbs.param[1+channel] >> 5) & 0x1;
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
}
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
} else {
Clean up some f/w revision checking wrt enabling fast posting. Make sure we set defaults sanely for dual-bus adapters.
1999-12-20 01:34:01 +00:00
sdp->isp_req_ack_active_neg = 1;
sdp->isp_data_line_active_neg = 1;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
Roll internal release tag. Print out if we're in a 64 bit PCI slot. Use fast memory timing NVRAM parameter. Clean up and fix establishment of default target parameters. Don't use NVRAM if are flagged as not to do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC mode but disabled disconnect/reconnect and wide!!). Fix delays after resets. BUS resets not done in isp_init anymore- relegated to OS specific outer layers. Fix a buglet where you can get in a loop for a NULL xs in the completion list in isp_intr. Add in some defines that can disable fast posting. Add in code for Loop Up/Loop Down events that call into the outer layers as to what to do.
1999-02-09 01:07:06 +00:00
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGDEBUG1,
"defaulting bus %d REQ/ACK Active Negation is %d",
channel, sdp->isp_req_ack_active_neg);
isp_prt(isp, ISP_LOGDEBUG1,
"defaulting bus %d DATA Active Negation is %d",
channel, sdp->isp_data_line_active_neg);
Clean up some f/w revision checking wrt enabling fast posting. Make sure we set defaults sanely for dual-bus adapters.
1999-12-20 01:34:01 +00:00
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
/*
* The trick here is to establish a default for the default (honk!)
* state (dev_flags). Then try and get the current status from
* the card to fill in the current state. We don't, in fact, set
* the default to the SAFE default state- that's not the goal state.
*/
for (tgt = 0; tgt < MAX_TARGETS; tgt++) {
sdp->isp_devparam[tgt].cur_offset = 0;
sdp->isp_devparam[tgt].cur_period = 0;
sdp->isp_devparam[tgt].dev_flags = DPARM_DEFAULT;
sdp->isp_devparam[tgt].cur_dflags = 0;
clean up for SBus Ultra (yes, we do not do that here yet)
2000-01-15 01:52:01 +00:00
/*
* We default to Wide/Fast for versions less than a 1040
* (unless it's SBus).
*/
if ((isp->isp_bustype == ISP_BT_SBUS &&
isp->isp_type < ISP_HA_SCSI_1020A) ||
(isp->isp_bustype == ISP_BT_PCI &&
isp->isp_type < ISP_HA_SCSI_1040) ||
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
(isp->isp_clock && isp->isp_clock < 60) ||
(sdp->isp_ultramode == 0)) {
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
sdp->isp_devparam[tgt].sync_offset =
Roll internal release tag. Print out if we're in a 64 bit PCI slot. Use fast memory timing NVRAM parameter. Clean up and fix establishment of default target parameters. Don't use NVRAM if are flagged as not to do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC mode but disabled disconnect/reconnect and wide!!). Fix delays after resets. BUS resets not done in isp_init anymore- relegated to OS specific outer layers. Fix a buglet where you can get in a loop for a NULL xs in the completion list in isp_intr. Add in some defines that can disable fast posting. Add in code for Loop Up/Loop Down events that call into the outer layers as to what to do.
1999-02-09 01:07:06 +00:00
ISP_10M_SYNCPARMS >> 8;
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
sdp->isp_devparam[tgt].sync_period =
Roll internal release tag. Print out if we're in a 64 bit PCI slot. Use fast memory timing NVRAM parameter. Clean up and fix establishment of default target parameters. Don't use NVRAM if are flagged as not to do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC mode but disabled disconnect/reconnect and wide!!). Fix delays after resets. BUS resets not done in isp_init anymore- relegated to OS specific outer layers. Fix a buglet where you can get in a loop for a NULL xs in the completion list in isp_intr. Add in some defines that can disable fast posting. Add in code for Loop Up/Loop Down events that call into the outer layers as to what to do.
1999-02-09 01:07:06 +00:00
ISP_10M_SYNCPARMS & 0xff;
various fixes
2000-08-27 23:38:44 +00:00
} else if (IS_ULTRA3(isp)) {
sdp->isp_devparam[tgt].sync_offset =
ISP_80M_SYNCPARMS >> 8;
sdp->isp_devparam[tgt].sync_period =
ISP_80M_SYNCPARMS & 0xff;
Add Dual LVD bus (1280) support
1999-12-16 05:42:02 +00:00
} else if (IS_ULTRA2(isp)) {
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
sdp->isp_devparam[tgt].sync_offset =
ISP_40M_SYNCPARMS >> 8;
sdp->isp_devparam[tgt].sync_period =
ISP_40M_SYNCPARMS & 0xff;
various fixes
2000-08-27 23:38:44 +00:00
} else if (IS_1240(isp)) {
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
sdp->isp_devparam[tgt].sync_offset =
Roll internal release tag. Print out if we're in a 64 bit PCI slot. Use fast memory timing NVRAM parameter. Clean up and fix establishment of default target parameters. Don't use NVRAM if are flagged as not to do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC mode but disabled disconnect/reconnect and wide!!). Fix delays after resets. BUS resets not done in isp_init anymore- relegated to OS specific outer layers. Fix a buglet where you can get in a loop for a NULL xs in the completion list in isp_intr. Add in some defines that can disable fast posting. Add in code for Loop Up/Loop Down events that call into the outer layers as to what to do.
1999-02-09 01:07:06 +00:00
ISP_20M_SYNCPARMS >> 8;
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
sdp->isp_devparam[tgt].sync_period =
Roll internal release tag. Print out if we're in a 64 bit PCI slot. Use fast memory timing NVRAM parameter. Clean up and fix establishment of default target parameters. Don't use NVRAM if are flagged as not to do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC mode but disabled disconnect/reconnect and wide!!). Fix delays after resets. BUS resets not done in isp_init anymore- relegated to OS specific outer layers. Fix a buglet where you can get in a loop for a NULL xs in the completion list in isp_intr. Add in some defines that can disable fast posting. Add in code for Loop Up/Loop Down events that call into the outer layers as to what to do.
1999-02-09 01:07:06 +00:00
ISP_20M_SYNCPARMS & 0xff;
various fixes
2000-08-27 23:38:44 +00:00
} else {
sdp->isp_devparam[tgt].sync_offset =
ISP_20M_SYNCPARMS_1040 >> 8;
sdp->isp_devparam[tgt].sync_period =
ISP_20M_SYNCPARMS_1040 & 0xff;
Roll internal release tag. Print out if we're in a 64 bit PCI slot. Use fast memory timing NVRAM parameter. Clean up and fix establishment of default target parameters. Don't use NVRAM if are flagged as not to do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC mode but disabled disconnect/reconnect and wide!!). Fix delays after resets. BUS resets not done in isp_init anymore- relegated to OS specific outer layers. Fix a buglet where you can get in a loop for a NULL xs in the completion list in isp_intr. Add in some defines that can disable fast posting. Add in code for Loop Up/Loop Down events that call into the outer layers as to what to do.
1999-02-09 01:07:06 +00:00
}
/*
* Don't get current target parameters if we've been
* told not to use NVRAM- it's really the same thing.
*/
Clean up some f/w revision checking wrt enabling fast posting. Make sure we set defaults sanely for dual-bus adapters.
1999-12-20 01:34:01 +00:00
if ((isp->isp_confopts & ISP_CFG_NONVRAM) == 0) {
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
Clean up some f/w revision checking wrt enabling fast posting. Make sure we set defaults sanely for dual-bus adapters.
1999-12-20 01:34:01 +00:00
mbs.param[0] = MBOX_GET_TARGET_PARAMS;
mbs.param[1] = tgt << 8;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_mboxcmd(isp, &mbs, MBLOGALL);
Clean up some f/w revision checking wrt enabling fast posting. Make sure we set defaults sanely for dual-bus adapters.
1999-12-20 01:34:01 +00:00
if (mbs.param[0] != MBOX_COMMAND_COMPLETE) {
continue;
}
sdp->isp_devparam[tgt].cur_dflags = mbs.param[2];
sdp->isp_devparam[tgt].dev_flags = mbs.param[2];
sdp->isp_devparam[tgt].cur_period = mbs.param[3] & 0xff;
sdp->isp_devparam[tgt].cur_offset = mbs.param[3] >> 8;
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
Clean up some f/w revision checking wrt enabling fast posting. Make sure we set defaults sanely for dual-bus adapters.
1999-12-20 01:34:01 +00:00
/*
* The maximum period we can really see
* here is 100 (decimal), or 400 ns.
* For some unknown reason we sometimes
* get back wildass numbers from the
* boot device's parameters (alpha only).
*/
if ((mbs.param[3] & 0xff) <= 0x64) {
sdp->isp_devparam[tgt].sync_period =
mbs.param[3] & 0xff;
sdp->isp_devparam[tgt].sync_offset =
mbs.param[3] >> 8;
}
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
Clean up some f/w revision checking wrt enabling fast posting. Make sure we set defaults sanely for dual-bus adapters.
1999-12-20 01:34:01 +00:00
/*
* It is not safe to run Ultra Mode with a clock < 60.
*/
if (((isp->isp_clock && isp->isp_clock < 60) ||
(isp->isp_type < ISP_HA_SCSI_1020A)) &&
(sdp->isp_devparam[tgt].sync_period <=
(ISP_20M_SYNCPARMS & 0xff))) {
sdp->isp_devparam[tgt].sync_offset =
ISP_10M_SYNCPARMS >> 8;
sdp->isp_devparam[tgt].sync_period =
ISP_10M_SYNCPARMS & 0xff;
}
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGDEBUG1,
various fixes
2000-08-27 23:38:44 +00:00
"Initial bus %d tgt %d flags %x offset %x period %x",
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
channel, tgt, sdp->isp_devparam[tgt].dev_flags,
clean up for SBus Ultra (yes, we do not do that here yet)
2000-01-15 01:52:01 +00:00
sdp->isp_devparam[tgt].sync_offset,
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
sdp->isp_devparam[tgt].sync_period);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
/*
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
* Establish default some more default parameters.
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
*/
sdp->isp_cmd_dma_burst_enable = 1;
sdp->isp_data_dma_burst_enabl = 1;
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
sdp->isp_fifo_threshold = 0;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
sdp->isp_initiator_id = DEFAULT_IID(isp);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
if (isp->isp_type >= ISP_HA_SCSI_1040) {
sdp->isp_async_data_setup = 9;
} else {
sdp->isp_async_data_setup = 6;
}
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
sdp->isp_selection_timeout = 250;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
sdp->isp_max_queue_depth = MAXISPREQUEST(isp);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
sdp->isp_tag_aging = 8;
sdp->isp_bus_reset_delay = 3;
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
sdp->isp_retry_count = 2;
sdp->isp_retry_delay = 2;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
for (tgt = 0; tgt < MAX_TARGETS; tgt++) {
various fixes
2000-08-27 23:38:44 +00:00
sdp->isp_devparam[tgt].exc_throttle = ISP_EXEC_THROTTLE;
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
sdp->isp_devparam[tgt].dev_enable = 1;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
}
Add in 1080 LVD support and some basis also for the 1240. The port database printout is now enabled.
1999-03-25 22:52:45 +00:00
/*
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
* Re-initialize the ISP and complete all orphaned commands
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
* with a 'botched' notice. The reset/init routines should
* not disturb an already active list of commands.
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
*
* Locks held prior to coming here.
*/
void
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_reinit(isp)
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
struct ispsoftc *isp;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
{
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
XS_T *xs;
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
u_int32_t handle;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
isp_reset(isp);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
if (isp->isp_state == ISP_RESETSTATE) {
isp_init(isp);
if (isp->isp_state == ISP_INITSTATE) {
isp->isp_state = ISP_RUNSTATE;
}
}
if (isp->isp_state != ISP_RUNSTATE) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGERR, "isp_reinit cannot restart ISP");
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
}
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
isp->isp_nactive = 0;
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
for (handle = 1; (int) handle <= isp->isp_maxcmds; handle++) {
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
xs = isp_find_xs(isp, handle);
if (xs == NULL) {
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
continue;
ISP_DMASETUP now returns a value to be possibly punted to outer layers. Turn request queue overflow messages into debug messages. Ensure on isp_restarts that we nullify the xflist array.
1998-09-17 21:03:45 +00:00
}
Remove some target mode stuff. It will get re-introduced in a different file later. Do some pencil-sharpening types of minor changes. Change how active commands are remembered (using new inline functions to get handles, etc..). Now do a GET FIRMWARE STATUS after firing up the f/w as outgoing mailbox 2 will tell you the f/w's notion of the max commands that can be supported. Attempt to retrieve loop topology. Add in the appropriate SWIZZLE/UNSWIZZLE macros calls (this is a no-op on Little Endian machines but is needed for sparc (on other platforms)). Move the temp port database we use to find out where things have moved to after a LIP to the softc and off the kernel stack. Follow Qlogic's hint and don't bother setting a tag for commands that don't have this enabled (presumably the f/w will do it's own selection then). Use an INT_PENDING macro to check for an interrupt. The call to ISP_DMAFREE now just takes the handle- not the 'handle-1' which was a layering violation. Use CFGPRINTF in a couple of places to make things less chatty if not booting verbose, or CAMDEBUG compiles, etc..
1999-10-17 18:58:22 +00:00
isp_destroy_handle(isp, handle);
if (XS_XFRLEN(xs)) {
ISP_DMAFREE(isp, xs, handle);
XS_RESID(xs) = XS_XFRLEN(xs);
} else {
XS_RESID(xs) = 0;
}
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
XS_SETERR(xs, HBA_BUSRESET);
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_done(xs);
Add support for the Qlogic ISP SCSI && FC/AL Adapters
1998-04-22 17:54:58 +00:00
}
}
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
/*
* NVRAM Routines
*/
static int
isp_read_nvram(isp)
struct ispsoftc *isp;
{
int i, amt;
u_int8_t csum, minversion;
union {
u_int8_t _x[ISP2100_NVRAM_SIZE];
u_int16_t _s[ISP2100_NVRAM_SIZE>>1];
} _n;
#define nvram_data _n._x
#define nvram_words _n._s
A wad of changes- prepping for 1080/1240 support (which caused a massive thwank in register layout goop). A different mboxcmd approach. Some PDB change infrastructure. Some better management of loopdown/loopup events (keep them distinct from resource starvation for simq freeze/unfreeze actions).
1999-03-17 05:04:39 +00:00
if (IS_FC(isp)) {
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
amt = ISP2100_NVRAM_SIZE;
minversion = 1;
Add Dual LVD bus (1280) support
1999-12-16 05:42:02 +00:00
} else if (IS_ULTRA2(isp)) {
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
amt = ISP1080_NVRAM_SIZE;
minversion = 0;
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
} else {
amt = ISP_NVRAM_SIZE;
minversion = 2;
}
/*
* Just read the first two words first to see if we have a valid
* NVRAM to continue reading the rest with.
*/
for (i = 0; i < 2; i++) {
isp_rdnvram_word(isp, i, &nvram_words[i]);
}
if (nvram_data[0] != 'I' || nvram_data[1] != 'S' ||
nvram_data[2] != 'P') {
if (isp->isp_bustype != ISP_BT_SBUS) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGWARN, "invalid NVRAM header");
isp_prt(isp, ISP_LOGDEBUG0, "%x %x %x",
nvram_data[0], nvram_data[1], nvram_data[2]);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
}
return (-1);
}
for (i = 2; i < amt>>1; i++) {
isp_rdnvram_word(isp, i, &nvram_words[i]);
}
for (csum = 0, i = 0; i < amt; i++) {
csum += nvram_data[i];
}
if (csum != 0) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGWARN, "invalid NVRAM checksum");
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
return (-1);
}
if (ISP_NVRAM_VERSION(nvram_data) < minversion) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGWARN, "version %d NVRAM not understood",
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
ISP_NVRAM_VERSION(nvram_data));
return (-1);
}
Restructure nvram reading routine to split out to separate functions for 1020/1X80/12160/2X00- for readability. Add in 12160 (Ultra3) support- but not with PPR just yet. Fix and clarify fetching of return parameter for getting firmware rev which for the 2200 contains the connection topology (Private Loop (NL-port), N-port, FL-port, F-port). Synthesize the connection topology for the 2100 which can only be Private Loop or FL-port. Handle a couple of new async mailbox commands which signify connection in Point-to-Point mode (N-port or F-port) or indicate various toe stubbing getting to same. Approved: jkh@freebsd.org
2000-02-11 19:31:32 +00:00
if (IS_ULTRA3(isp)) {
isp_parse_nvram_12160(isp, 0, nvram_data);
isp_parse_nvram_12160(isp, 1, nvram_data);
} else if (IS_1080(isp)) {
isp_parse_nvram_1080(isp, 0, nvram_data);
} else if (IS_1280(isp) || IS_1240(isp)) {
isp_parse_nvram_1080(isp, 0, nvram_data);
isp_parse_nvram_1080(isp, 1, nvram_data);
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
} else if (IS_SCSI(isp)) {
Restructure nvram reading routine to split out to separate functions for 1020/1X80/12160/2X00- for readability. Add in 12160 (Ultra3) support- but not with PPR just yet. Fix and clarify fetching of return parameter for getting firmware rev which for the 2200 contains the connection topology (Private Loop (NL-port), N-port, FL-port, F-port). Synthesize the connection topology for the 2100 which can only be Private Loop or FL-port. Handle a couple of new async mailbox commands which signify connection in Point-to-Point mode (N-port or F-port) or indicate various toe stubbing getting to same. Approved: jkh@freebsd.org
2000-02-11 19:31:32 +00:00
isp_parse_nvram_1020(isp, nvram_data);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
} else {
Restructure nvram reading routine to split out to separate functions for 1020/1X80/12160/2X00- for readability. Add in 12160 (Ultra3) support- but not with PPR just yet. Fix and clarify fetching of return parameter for getting firmware rev which for the 2200 contains the connection topology (Private Loop (NL-port), N-port, FL-port, F-port). Synthesize the connection topology for the 2100 which can only be Private Loop or FL-port. Handle a couple of new async mailbox commands which signify connection in Point-to-Point mode (N-port or F-port) or indicate various toe stubbing getting to same. Approved: jkh@freebsd.org
2000-02-11 19:31:32 +00:00
isp_parse_nvram_2100(isp, nvram_data);
Roll internal release tag. Print out if we're in a 64 bit PCI slot. Use fast memory timing NVRAM parameter. Clean up and fix establishment of default target parameters. Don't use NVRAM if are flagged as not to do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC mode but disabled disconnect/reconnect and wide!!). Fix delays after resets. BUS resets not done in isp_init anymore- relegated to OS specific outer layers. Fix a buglet where you can get in a loop for a NULL xs in the completion list in isp_intr. Add in some defines that can disable fast posting. Add in code for Loop Up/Loop Down events that call into the outer layers as to what to do.
1999-02-09 01:07:06 +00:00
}
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
return (0);
Restructure nvram reading routine to split out to separate functions for 1020/1X80/12160/2X00- for readability. Add in 12160 (Ultra3) support- but not with PPR just yet. Fix and clarify fetching of return parameter for getting firmware rev which for the 2200 contains the connection topology (Private Loop (NL-port), N-port, FL-port, F-port). Synthesize the connection topology for the 2100 which can only be Private Loop or FL-port. Handle a couple of new async mailbox commands which signify connection in Point-to-Point mode (N-port or F-port) or indicate various toe stubbing getting to same. Approved: jkh@freebsd.org
2000-02-11 19:31:32 +00:00
#undef nvram_data
#undef nvram_words
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
}
static void
isp_rdnvram_word(isp, wo, rp)
struct ispsoftc *isp;
int wo;
u_int16_t *rp;
{
int i, cbits;
u_int16_t bit, rqst;
ISP_WRITE(isp, BIU_NVRAM, BIU_NVRAM_SELECT);
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
USEC_DELAY(2);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
ISP_WRITE(isp, BIU_NVRAM, BIU_NVRAM_SELECT|BIU_NVRAM_CLOCK);
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
USEC_DELAY(2);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
if (IS_FC(isp)) {
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
wo &= ((ISP2100_NVRAM_SIZE >> 1) - 1);
rqst = (ISP_NVRAM_READ << 8) | wo;
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
cbits = 10;
Add Dual LVD bus (1280) support
1999-12-16 05:42:02 +00:00
} else if (IS_ULTRA2(isp)) {
Some massive thwunking in initialization to handle dual bus adapters. More massive thwunking to include an XS_CHANNEL value. Some changes of how parameters are reported to outer layers (including bus, e.g.). Yet more stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240 NVRAM.
1999-05-11 05:06:55 +00:00
wo &= ((ISP1080_NVRAM_SIZE >> 1) - 1);
rqst = (ISP_NVRAM_READ << 8) | wo;
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
cbits = 10;
} else {
wo &= ((ISP_NVRAM_SIZE >> 1) - 1);
rqst = (ISP_NVRAM_READ << 6) | wo;
cbits = 8;
}
/*
* Clock the word select request out...
*/
for (i = cbits; i >= 0; i--) {
if ((rqst >> i) & 1) {
bit = BIU_NVRAM_SELECT | BIU_NVRAM_DATAOUT;
} else {
bit = BIU_NVRAM_SELECT;
}
ISP_WRITE(isp, BIU_NVRAM, bit);
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
USEC_DELAY(2);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
ISP_WRITE(isp, BIU_NVRAM, bit | BIU_NVRAM_CLOCK);
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
USEC_DELAY(2);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
ISP_WRITE(isp, BIU_NVRAM, bit);
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
USEC_DELAY(2);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
}
/*
* Now read the result back in (bits come back in MSB format).
*/
*rp = 0;
for (i = 0; i < 16; i++) {
u_int16_t rv;
*rp <<= 1;
ISP_WRITE(isp, BIU_NVRAM, BIU_NVRAM_SELECT|BIU_NVRAM_CLOCK);
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
USEC_DELAY(2);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
rv = ISP_READ(isp, BIU_NVRAM);
if (rv & BIU_NVRAM_DATAIN) {
*rp |= 1;
}
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
USEC_DELAY(2);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
ISP_WRITE(isp, BIU_NVRAM, BIU_NVRAM_SELECT);
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
USEC_DELAY(2);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
}
ISP_WRITE(isp, BIU_NVRAM, 0);
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
USEC_DELAY(2);
ISP_SWIZZLE_NVRAM_WORD(isp, rp);
Update QLogic ISP support for CAM. Add preliminary target mode support. Submitted by: Matthew Jacob <mjacob@feral.com>
1998-09-15 08:42:56 +00:00
}
Restructure nvram reading routine to split out to separate functions for 1020/1X80/12160/2X00- for readability. Add in 12160 (Ultra3) support- but not with PPR just yet. Fix and clarify fetching of return parameter for getting firmware rev which for the 2200 contains the connection topology (Private Loop (NL-port), N-port, FL-port, F-port). Synthesize the connection topology for the 2100 which can only be Private Loop or FL-port. Handle a couple of new async mailbox commands which signify connection in Point-to-Point mode (N-port or F-port) or indicate various toe stubbing getting to same. Approved: jkh@freebsd.org
2000-02-11 19:31:32 +00:00
static void
isp_parse_nvram_1020(isp, nvram_data)
struct ispsoftc *isp;
u_int8_t *nvram_data;
{
int i;
sdparam *sdp = (sdparam *) isp->isp_param;
sdp->isp_fifo_threshold =
ISP_NVRAM_FIFO_THRESHOLD(nvram_data) |
(ISP_NVRAM_FIFO_THRESHOLD_128(nvram_data) << 2);
sdp->isp_initiator_id =
ISP_NVRAM_INITIATOR_ID(nvram_data);
sdp->isp_bus_reset_delay =
ISP_NVRAM_BUS_RESET_DELAY(nvram_data);
sdp->isp_retry_count =
ISP_NVRAM_BUS_RETRY_COUNT(nvram_data);
sdp->isp_retry_delay =
ISP_NVRAM_BUS_RETRY_DELAY(nvram_data);
sdp->isp_async_data_setup =
ISP_NVRAM_ASYNC_DATA_SETUP_TIME(nvram_data);
if (isp->isp_type >= ISP_HA_SCSI_1040) {
if (sdp->isp_async_data_setup < 9) {
sdp->isp_async_data_setup = 9;
}
} else {
if (sdp->isp_async_data_setup != 6) {
sdp->isp_async_data_setup = 6;
}
}
sdp->isp_req_ack_active_neg =
ISP_NVRAM_REQ_ACK_ACTIVE_NEGATION(nvram_data);
sdp->isp_data_line_active_neg =
ISP_NVRAM_DATA_LINE_ACTIVE_NEGATION(nvram_data);
sdp->isp_data_dma_burst_enabl =
ISP_NVRAM_DATA_DMA_BURST_ENABLE(nvram_data);
sdp->isp_cmd_dma_burst_enable =
ISP_NVRAM_CMD_DMA_BURST_ENABLE(nvram_data);
sdp->isp_tag_aging =
ISP_NVRAM_TAG_AGE_LIMIT(nvram_data);
sdp->isp_selection_timeout =
ISP_NVRAM_SELECTION_TIMEOUT(nvram_data);
sdp->isp_max_queue_depth =
ISP_NVRAM_MAX_QUEUE_DEPTH(nvram_data);
various fixes
2000-08-27 23:38:44 +00:00
sdp->isp_fast_mttr = ISP_NVRAM_FAST_MTTR_ENABLE(nvram_data);
Restructure nvram reading routine to split out to separate functions for 1020/1X80/12160/2X00- for readability. Add in 12160 (Ultra3) support- but not with PPR just yet. Fix and clarify fetching of return parameter for getting firmware rev which for the 2200 contains the connection topology (Private Loop (NL-port), N-port, FL-port, F-port). Synthesize the connection topology for the 2100 which can only be Private Loop or FL-port. Handle a couple of new async mailbox commands which signify connection in Point-to-Point mode (N-port or F-port) or indicate various toe stubbing getting to same. Approved: jkh@freebsd.org
2000-02-11 19:31:32 +00:00
for (i = 0; i < MAX_TARGETS; i++) {
sdp->isp_devparam[i].dev_enable =
ISP_NVRAM_TGT_DEVICE_ENABLE(nvram_data, i);
sdp->isp_devparam[i].exc_throttle =
ISP_NVRAM_TGT_EXEC_THROTTLE(nvram_data, i);
sdp->isp_devparam[i].sync_offset =
ISP_NVRAM_TGT_SYNC_OFFSET(nvram_data, i);
sdp->isp_devparam[i].sync_period =
ISP_NVRAM_TGT_SYNC_PERIOD(nvram_data, i);
if (isp->isp_type < ISP_HA_SCSI_1040) {
/*
* If we're not ultra, we can't possibly
* be a shorter period than this.
*/
if (sdp->isp_devparam[i].sync_period < 0x19) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
sdp->isp_devparam[i].sync_period = 0x19;
Restructure nvram reading routine to split out to separate functions for 1020/1X80/12160/2X00- for readability. Add in 12160 (Ultra3) support- but not with PPR just yet. Fix and clarify fetching of return parameter for getting firmware rev which for the 2200 contains the connection topology (Private Loop (NL-port), N-port, FL-port, F-port). Synthesize the connection topology for the 2100 which can only be Private Loop or FL-port. Handle a couple of new async mailbox commands which signify connection in Point-to-Point mode (N-port or F-port) or indicate various toe stubbing getting to same. Approved: jkh@freebsd.org
2000-02-11 19:31:32 +00:00
}
if (sdp->isp_devparam[i].sync_offset > 0xc) {
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
sdp->isp_devparam[i].sync_offset = 0x0c;
Restructure nvram reading routine to split out to separate functions for 1020/1X80/12160/2X00- for readability. Add in 12160 (Ultra3) support- but not with PPR just yet. Fix and clarify fetching of return parameter for getting firmware rev which for the 2200 contains the connection topology (Private Loop (NL-port), N-port, FL-port, F-port). Synthesize the connection topology for the 2100 which can only be Private Loop or FL-port. Handle a couple of new async mailbox commands which signify connection in Point-to-Point mode (N-port or F-port) or indicate various toe stubbing getting to same. Approved: jkh@freebsd.org
2000-02-11 19:31:32 +00:00
}
} else {
if (sdp->isp_devparam[i].sync_offset > 0x8) {
sdp->isp_devparam[i].sync_offset = 0x8;
}
}
sdp->isp_devparam[i].dev_flags = 0;
if (ISP_NVRAM_TGT_RENEG(nvram_data, i))
sdp->isp_devparam[i].dev_flags |= DPARM_RENEG;
sdp->isp_devparam[i].dev_flags |= DPARM_ARQ;
if (ISP_NVRAM_TGT_TQING(nvram_data, i))
sdp->isp_devparam[i].dev_flags |= DPARM_TQING;
if (ISP_NVRAM_TGT_SYNC(nvram_data, i))
sdp->isp_devparam[i].dev_flags |= DPARM_SYNC;
if (ISP_NVRAM_TGT_WIDE(nvram_data, i))
sdp->isp_devparam[i].dev_flags |= DPARM_WIDE;
if (ISP_NVRAM_TGT_PARITY(nvram_data, i))
sdp->isp_devparam[i].dev_flags |= DPARM_PARITY;
if (ISP_NVRAM_TGT_DISC(nvram_data, i))
sdp->isp_devparam[i].dev_flags |= DPARM_DISC;
sdp->isp_devparam[i].cur_dflags = 0; /* we don't know */
}
}
static void
isp_parse_nvram_1080(isp, bus, nvram_data)
struct ispsoftc *isp;
int bus;
u_int8_t *nvram_data;
{
int i;
sdparam *sdp = (sdparam *) isp->isp_param;
sdp += bus;
sdp->isp_fifo_threshold =
ISP1080_NVRAM_FIFO_THRESHOLD(nvram_data);
sdp->isp_initiator_id =
ISP1080_NVRAM_INITIATOR_ID(nvram_data, bus);
sdp->isp_bus_reset_delay =
ISP1080_NVRAM_BUS_RESET_DELAY(nvram_data, bus);
sdp->isp_retry_count =
ISP1080_NVRAM_BUS_RETRY_COUNT(nvram_data, bus);
sdp->isp_retry_delay =
ISP1080_NVRAM_BUS_RETRY_DELAY(nvram_data, bus);
sdp->isp_async_data_setup =
ISP1080_NVRAM_ASYNC_DATA_SETUP_TIME(nvram_data,
bus);
sdp->isp_req_ack_active_neg =
ISP1080_NVRAM_REQ_ACK_ACTIVE_NEGATION(nvram_data,
bus);
sdp->isp_data_line_active_neg =
ISP1080_NVRAM_DATA_LINE_ACTIVE_NEGATION(nvram_data,
bus);
sdp->isp_data_dma_burst_enabl =
ISP1080_NVRAM_BURST_ENABLE(nvram_data);
sdp->isp_cmd_dma_burst_enable =
ISP1080_NVRAM_BURST_ENABLE(nvram_data);
sdp->isp_selection_timeout =
ISP1080_NVRAM_SELECTION_TIMEOUT(nvram_data, bus);
sdp->isp_max_queue_depth =
ISP1080_NVRAM_MAX_QUEUE_DEPTH(nvram_data, bus);
for (i = 0; i < MAX_TARGETS; i++) {
sdp->isp_devparam[i].dev_enable =
ISP1080_NVRAM_TGT_DEVICE_ENABLE(nvram_data, i, bus);
sdp->isp_devparam[i].exc_throttle =
ISP1080_NVRAM_TGT_EXEC_THROTTLE(nvram_data, i, bus);
sdp->isp_devparam[i].sync_offset =
ISP1080_NVRAM_TGT_SYNC_OFFSET(nvram_data, i, bus);
sdp->isp_devparam[i].sync_period =
ISP1080_NVRAM_TGT_SYNC_PERIOD(nvram_data, i, bus);
sdp->isp_devparam[i].dev_flags = 0;
if (ISP1080_NVRAM_TGT_RENEG(nvram_data, i, bus))
sdp->isp_devparam[i].dev_flags |= DPARM_RENEG;
sdp->isp_devparam[i].dev_flags |= DPARM_ARQ;
if (ISP1080_NVRAM_TGT_TQING(nvram_data, i, bus))
sdp->isp_devparam[i].dev_flags |= DPARM_TQING;
if (ISP1080_NVRAM_TGT_SYNC(nvram_data, i, bus))
sdp->isp_devparam[i].dev_flags |= DPARM_SYNC;
if (ISP1080_NVRAM_TGT_WIDE(nvram_data, i, bus))
sdp->isp_devparam[i].dev_flags |= DPARM_WIDE;
if (ISP1080_NVRAM_TGT_PARITY(nvram_data, i, bus))
sdp->isp_devparam[i].dev_flags |= DPARM_PARITY;
if (ISP1080_NVRAM_TGT_DISC(nvram_data, i, bus))
sdp->isp_devparam[i].dev_flags |= DPARM_DISC;
sdp->isp_devparam[i].cur_dflags = 0;
}
}
static void
isp_parse_nvram_12160(isp, bus, nvram_data)
struct ispsoftc *isp;
int bus;
u_int8_t *nvram_data;
{
sdparam *sdp = (sdparam *) isp->isp_param;
int i;
sdp += bus;
sdp->isp_fifo_threshold =
ISP12160_NVRAM_FIFO_THRESHOLD(nvram_data);
sdp->isp_initiator_id =
ISP12160_NVRAM_INITIATOR_ID(nvram_data, bus);
sdp->isp_bus_reset_delay =
ISP12160_NVRAM_BUS_RESET_DELAY(nvram_data, bus);
sdp->isp_retry_count =
ISP12160_NVRAM_BUS_RETRY_COUNT(nvram_data, bus);
sdp->isp_retry_delay =
ISP12160_NVRAM_BUS_RETRY_DELAY(nvram_data, bus);
sdp->isp_async_data_setup =
ISP12160_NVRAM_ASYNC_DATA_SETUP_TIME(nvram_data,
bus);
sdp->isp_req_ack_active_neg =
ISP12160_NVRAM_REQ_ACK_ACTIVE_NEGATION(nvram_data,
bus);
sdp->isp_data_line_active_neg =
ISP12160_NVRAM_DATA_LINE_ACTIVE_NEGATION(nvram_data,
bus);
sdp->isp_data_dma_burst_enabl =
ISP12160_NVRAM_BURST_ENABLE(nvram_data);
sdp->isp_cmd_dma_burst_enable =
ISP12160_NVRAM_BURST_ENABLE(nvram_data);
sdp->isp_selection_timeout =
ISP12160_NVRAM_SELECTION_TIMEOUT(nvram_data, bus);
sdp->isp_max_queue_depth =
ISP12160_NVRAM_MAX_QUEUE_DEPTH(nvram_data, bus);
for (i = 0; i < MAX_TARGETS; i++) {
sdp->isp_devparam[i].dev_enable =
ISP12160_NVRAM_TGT_DEVICE_ENABLE(nvram_data, i, bus);
sdp->isp_devparam[i].exc_throttle =
ISP12160_NVRAM_TGT_EXEC_THROTTLE(nvram_data, i, bus);
sdp->isp_devparam[i].sync_offset =
ISP12160_NVRAM_TGT_SYNC_OFFSET(nvram_data, i, bus);
sdp->isp_devparam[i].sync_period =
ISP12160_NVRAM_TGT_SYNC_PERIOD(nvram_data, i, bus);
sdp->isp_devparam[i].dev_flags = 0;
if (ISP12160_NVRAM_TGT_RENEG(nvram_data, i, bus))
sdp->isp_devparam[i].dev_flags |= DPARM_RENEG;
sdp->isp_devparam[i].dev_flags |= DPARM_ARQ;
if (ISP12160_NVRAM_TGT_TQING(nvram_data, i, bus))
sdp->isp_devparam[i].dev_flags |= DPARM_TQING;
if (ISP12160_NVRAM_TGT_SYNC(nvram_data, i, bus))
sdp->isp_devparam[i].dev_flags |= DPARM_SYNC;
if (ISP12160_NVRAM_TGT_WIDE(nvram_data, i, bus))
sdp->isp_devparam[i].dev_flags |= DPARM_WIDE;
if (ISP12160_NVRAM_TGT_PARITY(nvram_data, i, bus))
sdp->isp_devparam[i].dev_flags |= DPARM_PARITY;
if (ISP12160_NVRAM_TGT_DISC(nvram_data, i, bus))
sdp->isp_devparam[i].dev_flags |= DPARM_DISC;
sdp->isp_devparam[i].cur_dflags = 0;
}
}
static void
isp_parse_nvram_2100(isp, nvram_data)
struct ispsoftc *isp;
u_int8_t *nvram_data;
{
fcparam *fcp = (fcparam *) isp->isp_param;
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
u_int64_t wwn;
Restructure nvram reading routine to split out to separate functions for 1020/1X80/12160/2X00- for readability. Add in 12160 (Ultra3) support- but not with PPR just yet. Fix and clarify fetching of return parameter for getting firmware rev which for the 2200 contains the connection topology (Private Loop (NL-port), N-port, FL-port, F-port). Synthesize the connection topology for the 2100 which can only be Private Loop or FL-port. Handle a couple of new async mailbox commands which signify connection in Point-to-Point mode (N-port or F-port) or indicate various toe stubbing getting to same. Approved: jkh@freebsd.org
2000-02-11 19:31:32 +00:00
/*
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
* There is supposed to be WWNN storage as distinct
* from WWPN storage in NVRAM, but it doesn't appear
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
* to be used sanely across all cards.
Restructure nvram reading routine to split out to separate functions for 1020/1X80/12160/2X00- for readability. Add in 12160 (Ultra3) support- but not with PPR just yet. Fix and clarify fetching of return parameter for getting firmware rev which for the 2200 contains the connection topology (Private Loop (NL-port), N-port, FL-port, F-port). Synthesize the connection topology for the 2100 which can only be Private Loop or FL-port. Handle a couple of new async mailbox commands which signify connection in Point-to-Point mode (N-port or F-port) or indicate various toe stubbing getting to same. Approved: jkh@freebsd.org
2000-02-11 19:31:32 +00:00
*/
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
wwn = ISP2100_NVRAM_PORT_NAME(nvram_data);
if (wwn != 0LL) {
switch ((int) (wwn >> 60)) {
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
case 0:
/*
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
* Broken PTI cards with nothing in the top nibble. Pah.
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
*/
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
wwn |= (2LL << 60);
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
/* FALLTHROUGH */
case 2:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
fcp->isp_nodewwn = wwn;
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
fcp->isp_nodewwn &= ~((0xfffLL) << 48);
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
fcp->isp_portwwn =
PORT_FROM_NODE_WWN(isp, fcp->isp_nodewwn);
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
break;
default:
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
fcp->isp_portwwn = fcp->isp_nodewwn = wwn;
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
}
Restructure nvram reading routine to split out to separate functions for 1020/1X80/12160/2X00- for readability. Add in 12160 (Ultra3) support- but not with PPR just yet. Fix and clarify fetching of return parameter for getting firmware rev which for the 2200 contains the connection topology (Private Loop (NL-port), N-port, FL-port, F-port). Synthesize the connection topology for the 2100 which can only be Private Loop or FL-port. Handle a couple of new async mailbox commands which signify connection in Point-to-Point mode (N-port or F-port) or indicate various toe stubbing getting to same. Approved: jkh@freebsd.org
2000-02-11 19:31:32 +00:00
}
Major whacking for core version 2.0. A major motivator for 2.0 and these changes is that there's now a Solaris port of this driver, so some things in the core version had to change (not much, but some). In order, from the top.....: A lot of error strings are gathered in one place at the head of the file. This caused me to rewrite them to look consistent (with respect to things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'. The major mailbox function, isp_mboxcmd, now takes a third argument, which is a mask that selectively says whether mailbox command failures will be logged. This will substantially reduce a lot of spurious noise from the driver. At the first run through isp_reset we used to try and get the current running firmware's revision by issuing a mailbox command. This would invariably fail on alpha's with anything but a Qlogic 1040 since SRM doesn't *start* the f/w on these cards. Instead, we now see whether we're sitting ROM state before trying to get a running BIOS loaded f/w version. All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to isp_prt. There are seperate print levels that can be independently set (see ispvar.h), which include debugging, etc. All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry indices, so we can make a 1024 entry index for them instead of the 256 entries we've had until now. A major change it to fix isp_fclink_test to actually only wait the delay of time specified in the microsecond argument being passed. The problem has always been that a call to isp_mboxcmd to get he current firmware state takes an unknown (sometimes long) amount of time- this is if the firmware is busy doing PLOGIs while we ask it what's up. So, up until now, the usdelay argument has been a joke. The net effect has been that if you boot without being plugged into a good loop or into a switch, you hang. Massively annonying, and hard to fix because the actual time delta was impossible to know from just guessing. Now, using the new GET_NANOTIME macros, a precise and measured amount of USEC_DELAY calls are done so that only the specified usecdelay is allowed to pass. This means that if the initial startup of the firmware if followed by a call from isp_freebsd.c:isp_attach to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000, no more than two seconds will actually elapse before we leave concluding that the cable is unhooked. Jeez. About time.... Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE macro to a call to the platform supplied isp_done (sane naming). Limit our size of request queue completions we'll look at at interrupt time. Since we've increased the size of the Request Queue (and the size of the Response Queue proportionally), let's not create an interrupt stack overflow by having to keep a max completion list (forw links are not an option because this is common code with some platforms that don't have link space in their XS_T structures). A limit of 32 is not unreasonable- I doubt there'd be even this many request queue completions at a time- remember, most boards now use fast posting for normal command completion instead of filling out response queue entries. In the isp_mboxcmd cleanup, also create an array of command names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8". Remove the isp_lostcmd function- it's been deprecated for a while. Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus register dump fucntion. Various other cleanups.
2000-08-01 06:51:05 +00:00
isp_prt(isp, ISP_LOGCONFIG, "NVRAM Derived Node WWN 0x%08x%08x",
(u_int32_t) (fcp->isp_nodewwn >> 32),
(u_int32_t) (fcp->isp_nodewwn & 0xffffffff));
isp_prt(isp, ISP_LOGCONFIG, "NVRAM Derived Port WWN 0x%08x%08x",
Fix some breakage about how we build WWNs. Do some other fabric related changes: consider a new PDB entry different if Class 3 service parameter roles change (!!!). Do some checking as we're getting a port database that traps whether things change while we're doing so. Handle N-port and F-ports correctly. Fix the fabric login loop to retain a login/binding if things haven't changed (I mean, why logout a device only to log it back in). No longer accept, after fabric logins, garbage if we can't get a PDB entry that matches the device we've just logged into- if it doesn't, log it out as it is very unlikely to still be what we thought it was. Get rid of some of the debounce loops because we could get stuck there.
2000-05-09 01:14:43 +00:00
(u_int32_t) (fcp->isp_portwwn >> 32),
(u_int32_t) (fcp->isp_portwwn & 0xffffffff));
Restructure nvram reading routine to split out to separate functions for 1020/1X80/12160/2X00- for readability. Add in 12160 (Ultra3) support- but not with PPR just yet. Fix and clarify fetching of return parameter for getting firmware rev which for the 2200 contains the connection topology (Private Loop (NL-port), N-port, FL-port, F-port). Synthesize the connection topology for the 2100 which can only be Private Loop or FL-port. Handle a couple of new async mailbox commands which signify connection in Point-to-Point mode (N-port or F-port) or indicate various toe stubbing getting to same. Approved: jkh@freebsd.org
2000-02-11 19:31:32 +00:00
fcp->isp_maxalloc =
ISP2100_NVRAM_MAXIOCBALLOCATION(nvram_data);
fcp->isp_maxfrmlen =
ISP2100_NVRAM_MAXFRAMELENGTH(nvram_data);
fcp->isp_retry_delay =
ISP2100_NVRAM_RETRY_DELAY(nvram_data);
fcp->isp_retry_count =
ISP2100_NVRAM_RETRY_COUNT(nvram_data);
fcp->isp_loopid =
ISP2100_NVRAM_HARDLOOPID(nvram_data);
fcp->isp_execthrottle =
ISP2100_NVRAM_EXECUTION_THROTTLE(nvram_data);
fcp->isp_fwoptions = ISP2100_NVRAM_OPTIONS(nvram_data);
}
Reference in New Issue Copy Permalink