freebsd-dev/sys/dev/usb2/ethernet/if_aue2.c

/*-
 * Copyright (c) 1997, 1998, 1999, 2000
 *	Bill Paul <wpaul@ee.columbia.edu>.  All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 * 3. All advertising materials mentioning features or use of this software
 *    must display the following acknowledgement:
 *	This product includes software developed by Bill Paul.
 * 4. Neither the name of the author nor the names of any co-contributors
 *    may be used to endorse or promote products derived from this software
 *    without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND
 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
 * ARE DISCLAIMED.  IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD
 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
 * THE POSSIBILITY OF SUCH DAMAGE.
 */

#include <sys/cdefs.h>
__FBSDID("$FreeBSD$");

/*
 * ADMtek AN986 Pegasus and AN8511 Pegasus II USB to ethernet driver.
 * Datasheet is available from http://www.admtek.com.tw.
 *
 * Written by Bill Paul <wpaul@ee.columbia.edu>
 * Electrical Engineering Department
 * Columbia University, New York City
 */

/*
 * The Pegasus chip uses four USB "endpoints" to provide 10/100 ethernet
 * support: the control endpoint for reading/writing registers, burst
 * read endpoint for packet reception, burst write for packet transmission
 * and one for "interrupts." The chip uses the same RX filter scheme
 * as the other ADMtek ethernet parts: one perfect filter entry for the
 * the station address and a 64-bit multicast hash table. The chip supports
 * both MII and HomePNA attachments.
 *
 * Since the maximum data transfer speed of USB is supposed to be 12Mbps,
 * you're never really going to get 100Mbps speeds from this device. I
 * think the idea is to allow the device to connect to 10 or 100Mbps
 * networks, not necessarily to provide 100Mbps performance. Also, since
 * the controller uses an external PHY chip, it's possible that board
 * designers might simply choose a 10Mbps PHY.
 *
 * Registers are accessed using usb2_do_request(). Packet transfers are
 * done using usb2_transfer() and friends.
 */

/*
 * NOTE: all function names beginning like "aue_cfg_" can only
 * be called from within the config thread function !
 */

#include <dev/usb2/include/usb2_devid.h>
#include <dev/usb2/include/usb2_standard.h>
#include <dev/usb2/include/usb2_mfunc.h>
#include <dev/usb2/include/usb2_error.h>

#define	usb2_config_td_cc usb2_ether_cc
#define	usb2_config_td_softc aue_softc

#define	USB_DEBUG_VAR aue_debug

#include <dev/usb2/core/usb2_core.h>
#include <dev/usb2/core/usb2_lookup.h>
#include <dev/usb2/core/usb2_process.h>
#include <dev/usb2/core/usb2_config_td.h>
#include <dev/usb2/core/usb2_debug.h>
#include <dev/usb2/core/usb2_request.h>
#include <dev/usb2/core/usb2_busdma.h>
#include <dev/usb2/core/usb2_util.h>

#include <dev/usb2/ethernet/usb2_ethernet.h>
#include <dev/usb2/ethernet/if_aue2_reg.h>

MODULE_DEPEND(aue, usb2_ethernet, 1, 1, 1);
MODULE_DEPEND(aue, usb2_core, 1, 1, 1);
MODULE_DEPEND(aue, ether, 1, 1, 1);
MODULE_DEPEND(aue, miibus, 1, 1, 1);

#if USB_DEBUG
static int aue_debug = 0;

SYSCTL_NODE(_hw_usb2, OID_AUTO, aue, CTLFLAG_RW, 0, "USB aue");
SYSCTL_INT(_hw_usb2_aue, OID_AUTO, debug, CTLFLAG_RW, &aue_debug, 0,
    "Debug level");
#endif

/*
 * Various supported device vendors/products.
 */
static const struct usb2_device_id aue_devs[] = {
	{USB_VPI(USB_VENDOR_3COM, USB_PRODUCT_3COM_3C460B, AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_ABOCOM, USB_PRODUCT_ABOCOM_DSB650TX_PNA, 0)},
	{USB_VPI(USB_VENDOR_ABOCOM, USB_PRODUCT_ABOCOM_UFE1000, AUE_FLAG_LSYS)},
	{USB_VPI(USB_VENDOR_ABOCOM, USB_PRODUCT_ABOCOM_XX10, 0)},
	{USB_VPI(USB_VENDOR_ABOCOM, USB_PRODUCT_ABOCOM_XX1, AUE_FLAG_PNA | AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_ABOCOM, USB_PRODUCT_ABOCOM_XX2, AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_ABOCOM, USB_PRODUCT_ABOCOM_XX4, AUE_FLAG_PNA)},
	{USB_VPI(USB_VENDOR_ABOCOM, USB_PRODUCT_ABOCOM_XX5, AUE_FLAG_PNA)},
	{USB_VPI(USB_VENDOR_ABOCOM, USB_PRODUCT_ABOCOM_XX6, AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_ABOCOM, USB_PRODUCT_ABOCOM_XX7, AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_ABOCOM, USB_PRODUCT_ABOCOM_XX8, AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_ABOCOM, USB_PRODUCT_ABOCOM_XX9, AUE_FLAG_PNA)},
	{USB_VPI(USB_VENDOR_ACCTON, USB_PRODUCT_ACCTON_SS1001, AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_ACCTON, USB_PRODUCT_ACCTON_USB320_EC, 0)},
	{USB_VPI(USB_VENDOR_ADMTEK, USB_PRODUCT_ADMTEK_PEGASUSII_2, AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_ADMTEK, USB_PRODUCT_ADMTEK_PEGASUSII_3, AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_ADMTEK, USB_PRODUCT_ADMTEK_PEGASUSII_4, AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_ADMTEK, USB_PRODUCT_ADMTEK_PEGASUSII, AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_ADMTEK, USB_PRODUCT_ADMTEK_PEGASUS, AUE_FLAG_PNA | AUE_FLAG_DUAL_PHY)},
	{USB_VPI(USB_VENDOR_AEI, USB_PRODUCT_AEI_FASTETHERNET, AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_ALLIEDTELESYN, USB_PRODUCT_ALLIEDTELESYN_ATUSB100, AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_ATEN, USB_PRODUCT_ATEN_UC110T, AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_BELKIN, USB_PRODUCT_BELKIN_USB2LAN, AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_BILLIONTON, USB_PRODUCT_BILLIONTON_USB100, 0)},
	{USB_VPI(USB_VENDOR_BILLIONTON, USB_PRODUCT_BILLIONTON_USBE100, AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_BILLIONTON, USB_PRODUCT_BILLIONTON_USBEL100, 0)},
	{USB_VPI(USB_VENDOR_BILLIONTON, USB_PRODUCT_BILLIONTON_USBLP100, AUE_FLAG_PNA)},
	{USB_VPI(USB_VENDOR_COREGA, USB_PRODUCT_COREGA_FETHER_USB_TXS, AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_COREGA, USB_PRODUCT_COREGA_FETHER_USB_TX, 0)},
	{USB_VPI(USB_VENDOR_DLINK, USB_PRODUCT_DLINK_DSB650TX1, AUE_FLAG_LSYS)},
	{USB_VPI(USB_VENDOR_DLINK, USB_PRODUCT_DLINK_DSB650TX2, AUE_FLAG_LSYS | AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_DLINK, USB_PRODUCT_DLINK_DSB650TX3, AUE_FLAG_LSYS | AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_DLINK, USB_PRODUCT_DLINK_DSB650TX4, AUE_FLAG_LSYS | AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_DLINK, USB_PRODUCT_DLINK_DSB650TX_PNA, AUE_FLAG_PNA)},
	{USB_VPI(USB_VENDOR_DLINK, USB_PRODUCT_DLINK_DSB650TX, AUE_FLAG_LSYS)},
	{USB_VPI(USB_VENDOR_DLINK, USB_PRODUCT_DLINK_DSB650, AUE_FLAG_LSYS)},
	{USB_VPI(USB_VENDOR_ELCON, USB_PRODUCT_ELCON_PLAN, AUE_FLAG_PNA | AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_ELECOM, USB_PRODUCT_ELECOM_LDUSB20, AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_ELECOM, USB_PRODUCT_ELECOM_LDUSBLTX, AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_ELECOM, USB_PRODUCT_ELECOM_LDUSBTX0, 0)},
	{USB_VPI(USB_VENDOR_ELECOM, USB_PRODUCT_ELECOM_LDUSBTX1, AUE_FLAG_LSYS)},
	{USB_VPI(USB_VENDOR_ELECOM, USB_PRODUCT_ELECOM_LDUSBTX2, 0)},
	{USB_VPI(USB_VENDOR_ELECOM, USB_PRODUCT_ELECOM_LDUSBTX3, AUE_FLAG_LSYS)},
	{USB_VPI(USB_VENDOR_ELSA, USB_PRODUCT_ELSA_USB2ETHERNET, 0)},
	{USB_VPI(USB_VENDOR_GIGABYTE, USB_PRODUCT_GIGABYTE_GNBR402W, 0)},
	{USB_VPI(USB_VENDOR_HAWKING, USB_PRODUCT_HAWKING_UF100, AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_HP, USB_PRODUCT_HP_HN210E, AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_IODATA, USB_PRODUCT_IODATA_USBETTXS, AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_IODATA, USB_PRODUCT_IODATA_USBETTX, 0)},
	{USB_VPI(USB_VENDOR_KINGSTON, USB_PRODUCT_KINGSTON_KNU101TX, 0)},
	{USB_VPI(USB_VENDOR_LINKSYS, USB_PRODUCT_LINKSYS_USB100H1, AUE_FLAG_LSYS | AUE_FLAG_PNA)},
	{USB_VPI(USB_VENDOR_LINKSYS, USB_PRODUCT_LINKSYS_USB100TX, AUE_FLAG_LSYS)},
	{USB_VPI(USB_VENDOR_LINKSYS, USB_PRODUCT_LINKSYS_USB10TA, AUE_FLAG_LSYS)},
	{USB_VPI(USB_VENDOR_LINKSYS, USB_PRODUCT_LINKSYS_USB10TX1, AUE_FLAG_LSYS | AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_LINKSYS, USB_PRODUCT_LINKSYS_USB10TX2, AUE_FLAG_LSYS | AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_LINKSYS, USB_PRODUCT_LINKSYS_USB10T, AUE_FLAG_LSYS)},
	{USB_VPI(USB_VENDOR_MELCO, USB_PRODUCT_MELCO_LUA2TX5, AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_MELCO, USB_PRODUCT_MELCO_LUATX1, 0)},
	{USB_VPI(USB_VENDOR_MELCO, USB_PRODUCT_MELCO_LUATX5, 0)},
	{USB_VPI(USB_VENDOR_MICROSOFT, USB_PRODUCT_MICROSOFT_MN110, AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_NETGEAR, USB_PRODUCT_NETGEAR_FA101, AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_SIEMENS, USB_PRODUCT_SIEMENS_SPEEDSTREAM, AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_SIIG2, USB_PRODUCT_SIIG2_USBTOETHER, AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_SMARTBRIDGES, USB_PRODUCT_SMARTBRIDGES_SMARTNIC, AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_SMC, USB_PRODUCT_SMC_2202USB, 0)},
	{USB_VPI(USB_VENDOR_SMC, USB_PRODUCT_SMC_2206USB, AUE_FLAG_PII)},
	{USB_VPI(USB_VENDOR_SOHOWARE, USB_PRODUCT_SOHOWARE_NUB100, 0)},
	{USB_VPI(USB_VENDOR_SOHOWARE, USB_PRODUCT_SOHOWARE_NUB110, AUE_FLAG_PII)},
};

/* prototypes */

static device_probe_t aue_probe;
static device_attach_t aue_attach;
static device_detach_t aue_detach;
static device_shutdown_t aue_shutdown;

static usb2_callback_t aue_intr_clear_stall_callback;
static usb2_callback_t aue_intr_callback;
static usb2_callback_t aue_bulk_read_clear_stall_callback;
static usb2_callback_t aue_bulk_read_callback;
static usb2_callback_t aue_bulk_write_clear_stall_callback;
static usb2_callback_t aue_bulk_write_callback;

static void aue_cfg_do_request(struct aue_softc *sc, struct usb2_device_request *req, void *data);
static uint8_t aue_cfg_csr_read_1(struct aue_softc *sc, uint16_t reg);
static uint16_t aue_cfg_csr_read_2(struct aue_softc *sc, uint16_t reg);
static void aue_cfg_csr_write_1(struct aue_softc *sc, uint16_t reg, uint8_t val);
static void aue_cfg_csr_write_2(struct aue_softc *sc, uint16_t reg, uint16_t val);
static void aue_cfg_eeprom_getword(struct aue_softc *sc, uint8_t addr, uint8_t *dest);
static void aue_cfg_read_eeprom(struct aue_softc *sc, uint8_t *dest, uint16_t off, uint16_t len);

static miibus_readreg_t aue_cfg_miibus_readreg;
static miibus_writereg_t aue_cfg_miibus_writereg;
static miibus_statchg_t aue_cfg_miibus_statchg;

static usb2_config_td_command_t aue_cfg_setmulti;
static usb2_config_td_command_t aue_cfg_first_time_setup;
static usb2_config_td_command_t aue_config_copy;
static usb2_config_td_command_t aue_cfg_tick;
static usb2_config_td_command_t aue_cfg_pre_init;
static usb2_config_td_command_t aue_cfg_init;
static usb2_config_td_command_t aue_cfg_promisc_upd;
static usb2_config_td_command_t aue_cfg_ifmedia_upd;
static usb2_config_td_command_t aue_cfg_pre_stop;
static usb2_config_td_command_t aue_cfg_stop;

static void aue_cfg_reset_pegasus_II(struct aue_softc *sc);
static void aue_cfg_reset(struct aue_softc *sc);
static void aue_start_cb(struct ifnet *ifp);
static void aue_init_cb(void *arg);
static void aue_start_transfers(struct aue_softc *sc);
static int aue_ifmedia_upd_cb(struct ifnet *ifp);
static void aue_ifmedia_sts_cb(struct ifnet *ifp, struct ifmediareq *ifmr);
static int aue_ioctl_cb(struct ifnet *ifp, u_long command, caddr_t data);
static void aue_watchdog(void *arg);

static const struct usb2_config aue_config[AUE_ENDPT_MAX] = {

	[0] = {
		.type = UE_BULK,
		.endpoint = UE_ADDR_ANY,
		.direction = UE_DIR_OUT,
		.mh.bufsize = (MCLBYTES + 2),
		.mh.flags = {.pipe_bof = 1,.force_short_xfer = 1,},
		.mh.callback = &aue_bulk_write_callback,
		.mh.timeout = 10000,	/* 10 seconds */
	},

	[1] = {
		.type = UE_BULK,
		.endpoint = UE_ADDR_ANY,
		.direction = UE_DIR_IN,
		.mh.bufsize = (MCLBYTES + 4 + ETHER_CRC_LEN),
		.mh.flags = {.pipe_bof = 1,.short_xfer_ok = 1,},
		.mh.callback = &aue_bulk_read_callback,
	},

	[2] = {
		.type = UE_CONTROL,
		.endpoint = 0x00,	/* Control pipe */
		.direction = UE_DIR_ANY,
		.mh.bufsize = sizeof(struct usb2_device_request),
		.mh.flags = {},
		.mh.callback = &aue_bulk_write_clear_stall_callback,
		.mh.timeout = 1000,	/* 1 second */
		.mh.interval = 50,	/* 50ms */
	},

	[3] = {
		.type = UE_CONTROL,
		.endpoint = 0x00,	/* Control pipe */
		.direction = UE_DIR_ANY,
		.mh.bufsize = sizeof(struct usb2_device_request),
		.mh.flags = {},
		.mh.callback = &aue_bulk_read_clear_stall_callback,
		.mh.timeout = 1000,	/* 1 second */
		.mh.interval = 50,	/* 50ms */
	},

	[4] = {
		.type = UE_INTERRUPT,
		.endpoint = UE_ADDR_ANY,
		.direction = UE_DIR_IN,
		.mh.flags = {.pipe_bof = 1,.short_xfer_ok = 1,},
		.mh.bufsize = 0,	/* use wMaxPacketSize */
		.mh.callback = &aue_intr_callback,
	},

	[5] = {
		.type = UE_CONTROL,
		.endpoint = 0x00,	/* Control pipe */
		.direction = UE_DIR_ANY,
		.mh.bufsize = sizeof(struct usb2_device_request),
		.mh.flags = {},
		.mh.callback = &aue_intr_clear_stall_callback,
		.mh.timeout = 1000,	/* 1 second */
		.mh.interval = 50,	/* 50ms */
	},
};

static device_method_t aue_methods[] = {
	/* Device interface */
	DEVMETHOD(device_probe, aue_probe),
	DEVMETHOD(device_attach, aue_attach),
	DEVMETHOD(device_detach, aue_detach),
	DEVMETHOD(device_shutdown, aue_shutdown),

	/* bus interface */
	DEVMETHOD(bus_print_child, bus_generic_print_child),
	DEVMETHOD(bus_driver_added, bus_generic_driver_added),

	/* MII interface */
	DEVMETHOD(miibus_readreg, aue_cfg_miibus_readreg),
	DEVMETHOD(miibus_writereg, aue_cfg_miibus_writereg),
	DEVMETHOD(miibus_statchg, aue_cfg_miibus_statchg),

	{0, 0}
};

static driver_t aue_driver = {
	.name = "aue",
	.methods = aue_methods,
	.size = sizeof(struct aue_softc)
};

static devclass_t aue_devclass;

DRIVER_MODULE(aue, ushub, aue_driver, aue_devclass, NULL, 0);
DRIVER_MODULE(miibus, aue, miibus_driver, miibus_devclass, 0, 0);

static void
aue_cfg_do_request(struct aue_softc *sc, struct usb2_device_request *req,
    void *data)
{
	uint16_t length;
	usb2_error_t err;

	if (usb2_config_td_is_gone(&sc->sc_config_td)) {
		goto error;
	}
	err = usb2_do_request_flags
	    (sc->sc_udev, &sc->sc_mtx, req, data, 0, NULL, 1000);

	if (err) {

		DPRINTF("device request failed, err=%s "
		    "(ignored)\n", usb2_errstr(err));

error:
		length = UGETW(req->wLength);

		if ((req->bmRequestType & UT_READ) && length) {
			bzero(data, length);
		}
	}
	return;
}

#define	AUE_CFG_SETBIT(sc, reg, x) \
	aue_cfg_csr_write_1(sc, reg, aue_cfg_csr_read_1(sc, reg) | (x))

#define	AUE_CFG_CLRBIT(sc, reg, x) \
	aue_cfg_csr_write_1(sc, reg, aue_cfg_csr_read_1(sc, reg) & ~(x))

static uint8_t
aue_cfg_csr_read_1(struct aue_softc *sc, uint16_t reg)
{
	struct usb2_device_request req;
	uint8_t val;

	req.bmRequestType = UT_READ_VENDOR_DEVICE;
	req.bRequest = AUE_UR_READREG;
	USETW(req.wValue, 0);
	USETW(req.wIndex, reg);
	USETW(req.wLength, 1);

	aue_cfg_do_request(sc, &req, &val);
	return (val);
}

static uint16_t
aue_cfg_csr_read_2(struct aue_softc *sc, uint16_t reg)
{
	struct usb2_device_request req;
	uint16_t val;

	req.bmRequestType = UT_READ_VENDOR_DEVICE;
	req.bRequest = AUE_UR_READREG;
	USETW(req.wValue, 0);
	USETW(req.wIndex, reg);
	USETW(req.wLength, 2);

	aue_cfg_do_request(sc, &req, &val);
	return (le16toh(val));
}

static void
aue_cfg_csr_write_1(struct aue_softc *sc, uint16_t reg, uint8_t val)
{
	struct usb2_device_request req;

	req.bmRequestType = UT_WRITE_VENDOR_DEVICE;
	req.bRequest = AUE_UR_WRITEREG;
	req.wValue[0] = val;
	req.wValue[1] = 0;
	USETW(req.wIndex, reg);
	USETW(req.wLength, 1);

	aue_cfg_do_request(sc, &req, &val);
	return;
}

static void
aue_cfg_csr_write_2(struct aue_softc *sc, uint16_t reg, uint16_t val)
{
	struct usb2_device_request req;

	req.bmRequestType = UT_WRITE_VENDOR_DEVICE;
	req.bRequest = AUE_UR_WRITEREG;
	USETW(req.wValue, val);
	USETW(req.wIndex, reg);
	USETW(req.wLength, 2);

	val = htole16(val);

	aue_cfg_do_request(sc, &req, &val);
	return;
}

/*
 * Read a word of data stored in the EEPROM at address 'addr.'
 */
static void
aue_cfg_eeprom_getword(struct aue_softc *sc, uint8_t addr,
    uint8_t *dest)
{
	uint16_t i;

	aue_cfg_csr_write_1(sc, AUE_EE_REG, addr);
	aue_cfg_csr_write_1(sc, AUE_EE_CTL, AUE_EECTL_READ);

	for (i = 0;; i++) {

		if (i < AUE_TIMEOUT) {

			if (aue_cfg_csr_read_1(sc, AUE_EE_CTL) & AUE_EECTL_DONE) {
				break;
			}
			if (usb2_config_td_sleep(&sc->sc_config_td, hz / 100)) {
				break;
			}
		} else {
			DPRINTF("EEPROM read timed out!\n");
			break;
		}
	}

	i = aue_cfg_csr_read_2(sc, AUE_EE_DATA);

	dest[0] = (i & 0xFF);
	dest[1] = (i >> 8);

	return;
}

/*
 * Read a sequence of words from the EEPROM.
 */
static void
aue_cfg_read_eeprom(struct aue_softc *sc, uint8_t *dest,
    uint16_t off, uint16_t len)
{
	uint16_t i;

	for (i = 0; i < len; i++) {
		aue_cfg_eeprom_getword(sc, off + i, dest + (i * 2));
	}
	return;
}

static int
aue_cfg_miibus_readreg(device_t dev, int phy, int reg)
{
	struct aue_softc *sc = device_get_softc(dev);
	uint16_t i;
	uint8_t do_unlock;

	/* avoid recursive locking */
	if (mtx_owned(&sc->sc_mtx)) {
		do_unlock = 0;
	} else {
		mtx_lock(&sc->sc_mtx);
		do_unlock = 1;
	}

	/*
	 * The Am79C901 HomePNA PHY actually contains
	 * two transceivers: a 1Mbps HomePNA PHY and a
	 * 10Mbps full/half duplex ethernet PHY with
	 * NWAY autoneg. However in the ADMtek adapter,
	 * only the 1Mbps PHY is actually connected to
	 * anything, so we ignore the 10Mbps one. It
	 * happens to be configured for MII address 3,
	 * so we filter that out.
	 */
	if (sc->sc_flags & AUE_FLAG_DUAL_PHY) {

		if (phy == 3) {
			i = 0;
			goto done;
		}
#if 0
		if (phy != 1) {
			i = 0;
			goto done;
		}
#endif
	}
	aue_cfg_csr_write_1(sc, AUE_PHY_ADDR, phy);
	aue_cfg_csr_write_1(sc, AUE_PHY_CTL, reg | AUE_PHYCTL_READ);

	for (i = 0;; i++) {

		if (i < AUE_TIMEOUT) {

			if (aue_cfg_csr_read_1(sc, AUE_PHY_CTL) & AUE_PHYCTL_DONE) {
				break;
			}
			if (usb2_config_td_sleep(&sc->sc_config_td, hz / 100)) {
				break;
			}
		} else {
			DPRINTF("MII read timed out\n");
			break;
		}
	}

	i = aue_cfg_csr_read_2(sc, AUE_PHY_DATA);

done:
	if (do_unlock) {
		mtx_unlock(&sc->sc_mtx);
	}
	return (i);
}

static int
aue_cfg_miibus_writereg(device_t dev, int phy, int reg, int data)
{
	struct aue_softc *sc = device_get_softc(dev);
	uint16_t i;
	uint8_t do_unlock;

	if (phy == 3) {
		return (0);
	}
	/* avoid recursive locking */
	if (mtx_owned(&sc->sc_mtx)) {
		do_unlock = 0;
	} else {
		mtx_lock(&sc->sc_mtx);
		do_unlock = 1;
	}

	aue_cfg_csr_write_2(sc, AUE_PHY_DATA, data);
	aue_cfg_csr_write_1(sc, AUE_PHY_ADDR, phy);
	aue_cfg_csr_write_1(sc, AUE_PHY_CTL, reg | AUE_PHYCTL_WRITE);

	for (i = 0;; i++) {

		if (i < AUE_TIMEOUT) {
			if (aue_cfg_csr_read_1(sc, AUE_PHY_CTL) & AUE_PHYCTL_DONE) {
				break;
			}
			if (usb2_config_td_sleep(&sc->sc_config_td, hz / 100)) {
				break;
			}
		} else {
			DPRINTF("MII write timed out\n");
			break;
		}
	}

	if (do_unlock) {
		mtx_unlock(&sc->sc_mtx);
	}
	return (0);
}

static void
aue_cfg_miibus_statchg(device_t dev)
{
	struct aue_softc *sc = device_get_softc(dev);
	struct mii_data *mii = GET_MII(sc);
	uint8_t do_unlock;

	/* avoid recursive locking */
	if (mtx_owned(&sc->sc_mtx)) {
		do_unlock = 0;
	} else {
		mtx_lock(&sc->sc_mtx);
		do_unlock = 1;
	}

	AUE_CFG_CLRBIT(sc, AUE_CTL0, AUE_CTL0_RX_ENB | AUE_CTL0_TX_ENB);

	if (IFM_SUBTYPE(mii->mii_media_active) == IFM_100_TX) {
		AUE_CFG_SETBIT(sc, AUE_CTL1, AUE_CTL1_SPEEDSEL);
	} else {
		AUE_CFG_CLRBIT(sc, AUE_CTL1, AUE_CTL1_SPEEDSEL);
	}

	if ((mii->mii_media_active & IFM_GMASK) == IFM_FDX) {
		AUE_CFG_SETBIT(sc, AUE_CTL1, AUE_CTL1_DUPLEX);
	} else {
		AUE_CFG_CLRBIT(sc, AUE_CTL1, AUE_CTL1_DUPLEX);
	}

	AUE_CFG_SETBIT(sc, AUE_CTL0, AUE_CTL0_RX_ENB | AUE_CTL0_TX_ENB);

	/*
	 * Set the LED modes on the LinkSys adapter.
	 * This turns on the 'dual link LED' bin in the auxmode
	 * register of the Broadcom PHY.
	 */
	if (sc->sc_flags & AUE_FLAG_LSYS) {
		uint16_t auxmode;

		auxmode = aue_cfg_miibus_readreg(dev, 0, 0x1b);
		aue_cfg_miibus_writereg(dev, 0, 0x1b, auxmode | 0x04);
	}
	if (do_unlock) {
		mtx_unlock(&sc->sc_mtx);
	}
	return;
}

static void
aue_cfg_setmulti(struct aue_softc *sc,
    struct usb2_config_td_cc *cc, uint16_t refcount)
{
	uint16_t i;

	if ((cc->if_flags & IFF_ALLMULTI) ||
	    (cc->if_flags & IFF_PROMISC)) {
		AUE_CFG_SETBIT(sc, AUE_CTL0, AUE_CTL0_ALLMULTI);
		return;
	}
	AUE_CFG_CLRBIT(sc, AUE_CTL0, AUE_CTL0_ALLMULTI);

	/* clear existing ones */
	for (i = 0; i < 8; i++) {
		aue_cfg_csr_write_1(sc, AUE_MAR0 + i, 0);
	}

	/* now program new ones */
	for (i = 0; i < 8; i++) {
		aue_cfg_csr_write_1(sc, AUE_MAR0 + i, cc->if_hash[i]);
	}
	return;
}

static void
aue_cfg_reset_pegasus_II(struct aue_softc *sc)
{
	/* Magic constants taken from Linux driver. */
	aue_cfg_csr_write_1(sc, AUE_REG_1D, 0);
	aue_cfg_csr_write_1(sc, AUE_REG_7B, 2);
#if 0
	if ((sc->sc_flags & HAS_HOME_PNA) && mii_mode)
		aue_cfg_csr_write_1(sc, AUE_REG_81, 6);
	else
#endif
		aue_cfg_csr_write_1(sc, AUE_REG_81, 2);

	return;
}

static void
aue_cfg_reset(struct aue_softc *sc)
{
	uint16_t i;

	AUE_CFG_SETBIT(sc, AUE_CTL1, AUE_CTL1_RESETMAC);

	for (i = 0;; i++) {

		if (i < AUE_TIMEOUT) {

			if (!(aue_cfg_csr_read_1(sc, AUE_CTL1) & AUE_CTL1_RESETMAC)) {
				break;
			}
			if (usb2_config_td_sleep(&sc->sc_config_td, hz / 100)) {
				break;
			}
		} else {
			DPRINTF("reset timed out\n");
			break;
		}
	}

	/*
	 * The PHY(s) attached to the Pegasus chip may be held
	 * in reset until we flip on the GPIO outputs. Make sure
	 * to set the GPIO pins high so that the PHY(s) will
	 * be enabled.
	 *
	 * Note: We force all of the GPIO pins low first, *then*
	 * enable the ones we want.
	 */
	aue_cfg_csr_write_1(sc, AUE_GPIO0, (AUE_GPIO_OUT0 | AUE_GPIO_SEL0));
	aue_cfg_csr_write_1(sc, AUE_GPIO0, (AUE_GPIO_OUT0 | AUE_GPIO_SEL0 |
	    AUE_GPIO_SEL1));

	if (sc->sc_flags & AUE_FLAG_LSYS) {
		/* Grrr. LinkSys has to be different from everyone else. */
		aue_cfg_csr_write_1(sc, AUE_GPIO0,
		    (AUE_GPIO_SEL0 | AUE_GPIO_SEL1));
		aue_cfg_csr_write_1(sc, AUE_GPIO0,
		    (AUE_GPIO_SEL0 |
		    AUE_GPIO_SEL1 |
		    AUE_GPIO_OUT0));
	}
	if (sc->sc_flags & AUE_FLAG_PII) {
		aue_cfg_reset_pegasus_II(sc);
	}
	/* wait a little while for the chip to get its brains in order: */
	usb2_config_td_sleep(&sc->sc_config_td, hz / 100);

	return;
}

/*
 * Probe for a Pegasus chip.
 */
static int
aue_probe(device_t dev)
{
	struct usb2_attach_arg *uaa = device_get_ivars(dev);

	if (uaa->usb2_mode != USB_MODE_HOST) {
		return (ENXIO);
	}
	if (uaa->info.bConfigIndex != AUE_CONFIG_INDEX) {
		return (ENXIO);
	}
	if (uaa->info.bIfaceIndex != AUE_IFACE_IDX) {
		return (ENXIO);
	}
	/*
	 * Belkin USB Bluetooth dongles of the F8T012xx1 model series
	 * conflict with older Belkin USB2LAN adapters. Skip if_aue if
	 * we detect one of the devices that look like Bluetooth
	 * adapters.
	 */
	if ((uaa->info.idVendor == USB_VENDOR_BELKIN) &&
	    (uaa->info.idProduct == USB_PRODUCT_BELKIN_F8T012) &&
	    (uaa->info.bcdDevice == 0x0413)) {
		return (ENXIO);
	}
	return (usb2_lookup_id_by_uaa(aue_devs, sizeof(aue_devs), uaa));
}

/*
 * Attach the interface. Allocate softc structures, do ifmedia
 * setup and ethernet/BPF attach.
 */
static int
aue_attach(device_t dev)
{
	struct usb2_attach_arg *uaa = device_get_ivars(dev);
	struct aue_softc *sc = device_get_softc(dev);
	int32_t error;
	uint8_t iface_index;

	if (sc == NULL) {
		return (ENOMEM);
	}
	sc->sc_udev = uaa->device;
	sc->sc_dev = dev;
	sc->sc_unit = device_get_unit(dev);
	sc->sc_flags = USB_GET_DRIVER_INFO(uaa);

	if (uaa->info.bcdDevice >= 0x0201) {
		sc->sc_flags |= AUE_FLAG_VER_2;	/* XXX currently undocumented */
	}
	device_set_usb2_desc(dev);

	snprintf(sc->sc_name, sizeof(sc->sc_name), "%s",
	    device_get_nameunit(dev));

	mtx_init(&sc->sc_mtx, "aue lock", NULL, MTX_DEF | MTX_RECURSE);

	usb2_callout_init_mtx(&sc->sc_watchdog,
	    &sc->sc_mtx, CALLOUT_RETURNUNLOCKED);

	iface_index = AUE_IFACE_IDX;
	error = usb2_transfer_setup(uaa->device, &iface_index,
	    sc->sc_xfer, aue_config, AUE_ENDPT_MAX,
	    sc, &sc->sc_mtx);
	if (error) {
		device_printf(dev, "allocating USB "
		    "transfers failed!\n");
		goto detach;
	}
	error = usb2_config_td_setup(&sc->sc_config_td, sc, &sc->sc_mtx,
	    NULL, sizeof(struct usb2_config_td_cc), 16);
	if (error) {
		device_printf(dev, "could not setup config "
		    "thread!\n");
		goto detach;
	}
	mtx_lock(&sc->sc_mtx);

	sc->sc_flags |= AUE_FLAG_WAIT_LINK;

	/* start setup */

	usb2_config_td_queue_command
	    (&sc->sc_config_td, NULL, &aue_cfg_first_time_setup, 0, 0);

	/* start watchdog (will exit mutex) */

	aue_watchdog(sc);

	return (0);			/* success */

detach:
	aue_detach(dev);
	return (ENXIO);			/* failure */
}

static void
aue_cfg_first_time_setup(struct aue_softc *sc,
    struct usb2_config_td_cc *cc, uint16_t refcount)
{
	struct ifnet *ifp;
	int error;
	uint8_t eaddr[min(ETHER_ADDR_LEN, 6)];

	/* reset the adapter */
	aue_cfg_reset(sc);

	/* set default value */
	bzero(eaddr, sizeof(eaddr));

	/* get station address from the EEPROM */
	aue_cfg_read_eeprom(sc, eaddr, 0, 3);

	mtx_unlock(&sc->sc_mtx);

	ifp = if_alloc(IFT_ETHER);

	mtx_lock(&sc->sc_mtx);

	if (ifp == NULL) {
		printf("%s: could not if_alloc()\n",
		    sc->sc_name);
		goto done;
	}
	sc->sc_evilhack = ifp;

	ifp->if_softc = sc;
	if_initname(ifp, "aue", sc->sc_unit);
	ifp->if_mtu = ETHERMTU;
	ifp->if_flags = IFF_BROADCAST | IFF_SIMPLEX | IFF_MULTICAST;
	ifp->if_ioctl = aue_ioctl_cb;
	ifp->if_start = aue_start_cb;
	ifp->if_watchdog = NULL;
	ifp->if_init = aue_init_cb;
	IFQ_SET_MAXLEN(&ifp->if_snd, IFQ_MAXLEN);
	ifp->if_snd.ifq_drv_maxlen = IFQ_MAXLEN;
	IFQ_SET_READY(&ifp->if_snd);

	/*
	 * XXX need Giant when accessing the device structures !
	 */

	mtx_unlock(&sc->sc_mtx);

	mtx_lock(&Giant);

	error = mii_phy_probe(sc->sc_dev, &sc->sc_miibus,
	    &aue_ifmedia_upd_cb,
	    &aue_ifmedia_sts_cb);

	mtx_unlock(&Giant);

	mtx_lock(&sc->sc_mtx);

	/*
	 * Do MII setup.
	 * NOTE: Doing this causes child devices to be attached to us,
	 * which we would normally disconnect at in the detach routine
	 * using device_delete_child(). However the USB code is set up
	 * such that when this driver is removed, all children devices
	 * are removed as well. In effect, the USB code ends up detaching
	 * all of our children for us, so we don't have to do is ourselves
	 * in aue_detach(). It's important to point this out since if
	 * we *do* try to detach the child devices ourselves, we will
	 * end up getting the children deleted twice, which will crash
	 * the system.
	 */
	if (error) {
		printf("%s: MII without any PHY!\n",
		    sc->sc_name);
		if_free(ifp);
		goto done;
	}
	sc->sc_ifp = ifp;

	mtx_unlock(&sc->sc_mtx);

	/*
	 * Call MI attach routine.
	 */
	ether_ifattach(ifp, eaddr);

	mtx_lock(&sc->sc_mtx);

done:
	return;
}

static int
aue_detach(device_t dev)
{
	struct aue_softc *sc = device_get_softc(dev);
	struct ifnet *ifp;

	usb2_config_td_drain(&sc->sc_config_td);

	mtx_lock(&sc->sc_mtx);

	usb2_callout_stop(&sc->sc_watchdog);

	aue_cfg_pre_stop(sc, NULL, 0);

	ifp = sc->sc_ifp;

	mtx_unlock(&sc->sc_mtx);

	/* stop all USB transfers first */
	usb2_transfer_unsetup(sc->sc_xfer, AUE_ENDPT_MAX);

	/* get rid of any late children */
	bus_generic_detach(dev);

	if (ifp) {
		ether_ifdetach(ifp);
		if_free(ifp);
	}
	usb2_config_td_unsetup(&sc->sc_config_td);

	usb2_callout_drain(&sc->sc_watchdog);

	mtx_destroy(&sc->sc_mtx);

	return (0);
}

static void
aue_intr_clear_stall_callback(struct usb2_xfer *xfer)
{
	struct aue_softc *sc = xfer->priv_sc;
	struct usb2_xfer *xfer_other = sc->sc_xfer[4];

	if (usb2_clear_stall_callback(xfer, xfer_other)) {
		DPRINTF("stall cleared\n");
		sc->sc_flags &= ~AUE_FLAG_INTR_STALL;
		usb2_transfer_start(xfer_other);
	}
	return;
}

static void
aue_intr_callback(struct usb2_xfer *xfer)
{
	struct aue_softc *sc = xfer->priv_sc;
	struct ifnet *ifp = sc->sc_ifp;
	struct aue_intrpkt pkt;

	switch (USB_GET_STATE(xfer)) {
	case USB_ST_TRANSFERRED:

		if (ifp && (ifp->if_drv_flags & IFF_DRV_RUNNING) &&
		    (xfer->actlen >= sizeof(pkt))) {

			usb2_copy_out(xfer->frbuffers, 0, &pkt, sizeof(pkt));

			if (pkt.aue_txstat0) {
				ifp->if_oerrors++;
			}
			if (pkt.aue_txstat0 & (AUE_TXSTAT0_LATECOLL &
			    AUE_TXSTAT0_EXCESSCOLL)) {
				ifp->if_collisions++;
			}
		}
	case USB_ST_SETUP:
		if (sc->sc_flags & AUE_FLAG_INTR_STALL) {
			usb2_transfer_start(sc->sc_xfer[5]);
		} else {
			xfer->frlengths[0] = xfer->max_data_length;
			usb2_start_hardware(xfer);
		}
		return;

	default:			/* Error */
		if (xfer->error != USB_ERR_CANCELLED) {
			/* start clear stall */
			sc->sc_flags |= AUE_FLAG_INTR_STALL;
			usb2_transfer_start(sc->sc_xfer[5]);
		}
		return;
	}
}

static void
aue_bulk_read_clear_stall_callback(struct usb2_xfer *xfer)
{
	struct aue_softc *sc = xfer->priv_sc;
	struct usb2_xfer *xfer_other = sc->sc_xfer[1];

	if (usb2_clear_stall_callback(xfer, xfer_other)) {
		DPRINTF("stall cleared\n");
		sc->sc_flags &= ~AUE_FLAG_READ_STALL;
		usb2_transfer_start(xfer_other);
	}
	return;
}

static void
aue_bulk_read_callback(struct usb2_xfer *xfer)
{
	struct aue_softc *sc = xfer->priv_sc;
	struct ifnet *ifp = sc->sc_ifp;
	struct mbuf *m = NULL;

	switch (USB_GET_STATE(xfer)) {
	case USB_ST_TRANSFERRED:
		DPRINTFN(11, "received %d bytes\n", xfer->actlen);

		if (sc->sc_flags & AUE_FLAG_VER_2) {

			if (xfer->actlen == 0) {
				ifp->if_ierrors++;
				goto tr_setup;
			}
		} else {

			if (xfer->actlen <= (4 + ETHER_CRC_LEN)) {
				ifp->if_ierrors++;
				goto tr_setup;
			}
			usb2_copy_out(xfer->frbuffers, xfer->actlen - 4, &sc->sc_rxpkt,
			    sizeof(sc->sc_rxpkt));

			/*
			 * turn off all the non-error bits in the rx status
			 * word:
			 */
			sc->sc_rxpkt.aue_rxstat &= AUE_RXSTAT_MASK;

			if (sc->sc_rxpkt.aue_rxstat) {
				ifp->if_ierrors++;
				goto tr_setup;
			}
			/* No errors; receive the packet. */
			xfer->actlen -= (4 + ETHER_CRC_LEN);
		}

		m = usb2_ether_get_mbuf();

		if (m == NULL) {
			ifp->if_ierrors++;
			goto tr_setup;
		}
		xfer->actlen = min(xfer->actlen, m->m_len);

		usb2_copy_out(xfer->frbuffers, 0, m->m_data, xfer->actlen);

		ifp->if_ipackets++;
		m->m_pkthdr.rcvif = ifp;
		m->m_pkthdr.len = m->m_len = xfer->actlen;

	case USB_ST_SETUP:
tr_setup:

		if (sc->sc_flags & AUE_FLAG_READ_STALL) {
			usb2_transfer_start(sc->sc_xfer[3]);
		} else {
			xfer->frlengths[0] = xfer->max_data_length;
			usb2_start_hardware(xfer);
		}

		/*
		 * At the end of a USB callback it is always safe to unlock
		 * the private mutex of a device! That is why we do the
		 * "if_input" here, and not some lines up!
		 */
		if (m) {
			mtx_unlock(&sc->sc_mtx);
			(ifp->if_input) (ifp, m);
			mtx_lock(&sc->sc_mtx);
		}
		return;

	default:			/* Error */
		if (xfer->error != USB_ERR_CANCELLED) {
			/* try to clear stall first */
			sc->sc_flags |= AUE_FLAG_READ_STALL;
			usb2_transfer_start(sc->sc_xfer[3]);
		}
		DPRINTF("bulk read error, %s\n",
		    usb2_errstr(xfer->error));
		return;

	}
}

static void
aue_bulk_write_clear_stall_callback(struct usb2_xfer *xfer)
{
	struct aue_softc *sc = xfer->priv_sc;
	struct usb2_xfer *xfer_other = sc->sc_xfer[0];

	if (usb2_clear_stall_callback(xfer, xfer_other)) {
		DPRINTF("stall cleared\n");
		sc->sc_flags &= ~AUE_FLAG_WRITE_STALL;
		usb2_transfer_start(xfer_other);
	}
	return;
}

static void
aue_bulk_write_callback(struct usb2_xfer *xfer)
{
	struct aue_softc *sc = xfer->priv_sc;
	struct ifnet *ifp = sc->sc_ifp;
	struct mbuf *m;
	uint8_t buf[2];

	switch (USB_GET_STATE(xfer)) {
	case USB_ST_TRANSFERRED:
		DPRINTFN(11, "transfer of %d bytes complete\n", xfer->actlen);

		ifp->if_opackets++;

	case USB_ST_SETUP:

		if (sc->sc_flags & AUE_FLAG_WRITE_STALL) {
			usb2_transfer_start(sc->sc_xfer[2]);
			goto done;
		}
		if (sc->sc_flags & AUE_FLAG_WAIT_LINK) {
			/*
			 * don't send anything if there is no link !
			 */
			goto done;
		}
		IFQ_DRV_DEQUEUE(&ifp->if_snd, m);

		if (m == NULL) {
			goto done;
		}
		if (m->m_pkthdr.len > MCLBYTES) {
			m->m_pkthdr.len = MCLBYTES;
		}
		if (sc->sc_flags & AUE_FLAG_VER_2) {

			xfer->frlengths[0] = m->m_pkthdr.len;

			usb2_m_copy_in(xfer->frbuffers, 0,
			    m, 0, m->m_pkthdr.len);

		} else {

			xfer->frlengths[0] = (m->m_pkthdr.len + 2);

			/*
		         * The ADMtek documentation says that the packet length is
		         * supposed to be specified in the first two bytes of the
		         * transfer, however it actually seems to ignore this info
		         * and base the frame size on the bulk transfer length.
		         */
			buf[0] = (uint8_t)(m->m_pkthdr.len);
			buf[1] = (uint8_t)(m->m_pkthdr.len >> 8);

			usb2_copy_in(xfer->frbuffers, 0, buf, 2);

			usb2_m_copy_in(xfer->frbuffers, 2,
			    m, 0, m->m_pkthdr.len);
		}

		/*
		 * if there's a BPF listener, bounce a copy
		 * of this frame to him:
		 */
		BPF_MTAP(ifp, m);

		m_freem(m);

		usb2_start_hardware(xfer);

done:
		return;

	default:			/* Error */
		DPRINTFN(11, "transfer error, %s\n",
		    usb2_errstr(xfer->error));

		if (xfer->error != USB_ERR_CANCELLED) {
			/* try to clear stall first */
			sc->sc_flags |= AUE_FLAG_WRITE_STALL;
			usb2_transfer_start(sc->sc_xfer[2]);
		}
		ifp->if_oerrors++;
		return;

	}
}

#define	AUE_BITS 6

static void
aue_mchash(struct usb2_config_td_cc *cc, const uint8_t *ptr)
{
	uint8_t h;

	h = ether_crc32_le(ptr, ETHER_ADDR_LEN) &
	    ((1 << AUE_BITS) - 1);
	cc->if_hash[(h >> 3)] |= (1 << (h & 7));
	return;
}

static void
aue_config_copy(struct aue_softc *sc,
    struct usb2_config_td_cc *cc, uint16_t refcount)
{
	bzero(cc, sizeof(*cc));
	usb2_ether_cc(sc->sc_ifp, &aue_mchash, cc);
	return;
}

static void
aue_cfg_tick(struct aue_softc *sc,
    struct usb2_config_td_cc *cc, uint16_t refcount)
{
	struct ifnet *ifp = sc->sc_ifp;
	struct mii_data *mii = GET_MII(sc);

	if ((ifp == NULL) ||
	    (mii == NULL)) {
		/* not ready */
		return;
	}
	mii_tick(mii);

	mii_pollstat(mii);

	if ((sc->sc_flags & AUE_FLAG_WAIT_LINK) &&
	    (mii->mii_media_status & IFM_ACTIVE) &&
	    (IFM_SUBTYPE(mii->mii_media_active) != IFM_NONE)) {
		sc->sc_flags &= ~AUE_FLAG_WAIT_LINK;
	}
	sc->sc_media_active = mii->mii_media_active;
	sc->sc_media_status = mii->mii_media_status;

	/* start stopped transfers, if any */

	aue_start_transfers(sc);

	return;
}

static void
aue_start_cb(struct ifnet *ifp)
{
	struct aue_softc *sc = ifp->if_softc;

	mtx_lock(&sc->sc_mtx);

	aue_start_transfers(sc);

	mtx_unlock(&sc->sc_mtx);

	return;
}

static void
aue_init_cb(void *arg)
{
	struct aue_softc *sc = arg;

	mtx_lock(&sc->sc_mtx);
	usb2_config_td_queue_command
	    (&sc->sc_config_td, &aue_cfg_pre_init, &aue_cfg_init, 0, 0);
	mtx_unlock(&sc->sc_mtx);

	return;
}

static void
aue_start_transfers(struct aue_softc *sc)
{
	if ((sc->sc_flags & AUE_FLAG_LL_READY) &&
	    (sc->sc_flags & AUE_FLAG_HL_READY)) {

		/*
		 * start the USB transfers, if not already started:
		 */
		usb2_transfer_start(sc->sc_xfer[4]);
		usb2_transfer_start(sc->sc_xfer[1]);
		usb2_transfer_start(sc->sc_xfer[0]);
	}
	return;
}

static void
aue_cfg_pre_init(struct aue_softc *sc,
    struct usb2_config_td_cc *cc, uint16_t refcount)
{
	struct ifnet *ifp = sc->sc_ifp;

	/* immediate configuration */

	aue_cfg_pre_stop(sc, cc, 0);

	ifp->if_drv_flags |= IFF_DRV_RUNNING;

	sc->sc_flags |= AUE_FLAG_HL_READY;
	return;
}

static void
aue_cfg_init(struct aue_softc *sc,
    struct usb2_config_td_cc *cc, uint16_t refcount)
{
	struct mii_data *mii = GET_MII(sc);
	uint8_t i;

	/*
	 * Cancel pending I/O
	 */
	aue_cfg_stop(sc, cc, 0);

	/* Set MAC address */
	for (i = 0; i < ETHER_ADDR_LEN; i++) {
		aue_cfg_csr_write_1(sc, AUE_PAR0 + i, cc->if_lladdr[i]);
	}

	/* update promiscuous setting */
	aue_cfg_promisc_upd(sc, cc, 0);

	/* load the multicast filter */
	aue_cfg_setmulti(sc, cc, 0);

	/* enable RX and TX */
	aue_cfg_csr_write_1(sc, AUE_CTL0,
	    (AUE_CTL0_RXSTAT_APPEND |
	    AUE_CTL0_RX_ENB));

	AUE_CFG_SETBIT(sc, AUE_CTL0, AUE_CTL0_TX_ENB);
	AUE_CFG_SETBIT(sc, AUE_CTL2, AUE_CTL2_EP3_CLR);

	mii_mediachg(mii);

	sc->sc_flags |= (AUE_FLAG_READ_STALL |
	    AUE_FLAG_WRITE_STALL |
	    AUE_FLAG_LL_READY);

	aue_start_transfers(sc);
	return;
}

static void
aue_cfg_promisc_upd(struct aue_softc *sc,
    struct usb2_config_td_cc *cc, uint16_t refcount)
{
	/* if we want promiscuous mode, set the allframes bit: */
	if (cc->if_flags & IFF_PROMISC) {
		AUE_CFG_SETBIT(sc, AUE_CTL2, AUE_CTL2_RX_PROMISC);
	} else {
		AUE_CFG_CLRBIT(sc, AUE_CTL2, AUE_CTL2_RX_PROMISC);
	}
	return;
}

/*
 * Set media options.
 */
static int
aue_ifmedia_upd_cb(struct ifnet *ifp)
{
	struct aue_softc *sc = ifp->if_softc;

	mtx_lock(&sc->sc_mtx);
	usb2_config_td_queue_command
	    (&sc->sc_config_td, NULL, &aue_cfg_ifmedia_upd, 0, 0);
	mtx_unlock(&sc->sc_mtx);

	return (0);
}

static void
aue_cfg_ifmedia_upd(struct aue_softc *sc,
    struct usb2_config_td_cc *cc, uint16_t refcount)
{
	struct ifnet *ifp = sc->sc_ifp;
	struct mii_data *mii = GET_MII(sc);

	if ((ifp == NULL) ||
	    (mii == NULL)) {
		/* not ready */
		return;
	}
	sc->sc_flags |= AUE_FLAG_WAIT_LINK;

	if (mii->mii_instance) {
		struct mii_softc *miisc;

		LIST_FOREACH(miisc, &mii->mii_phys, mii_list) {
			mii_phy_reset(miisc);
		}
	}
	mii_mediachg(mii);

	return;
}

/*
 * Report current media status.
 */
static void
aue_ifmedia_sts_cb(struct ifnet *ifp, struct ifmediareq *ifmr)
{
	struct aue_softc *sc = ifp->if_softc;

	mtx_lock(&sc->sc_mtx);

	ifmr->ifm_active = sc->sc_media_active;
	ifmr->ifm_status = sc->sc_media_status;

	mtx_unlock(&sc->sc_mtx);
	return;
}

static int
aue_ioctl_cb(struct ifnet *ifp, u_long command, caddr_t data)
{
	struct aue_softc *sc = ifp->if_softc;
	struct mii_data *mii;
	int error = 0;

	switch (command) {
	case SIOCSIFFLAGS:
		mtx_lock(&sc->sc_mtx);
		if (ifp->if_flags & IFF_UP) {
			if (ifp->if_drv_flags & IFF_DRV_RUNNING) {
				usb2_config_td_queue_command
				    (&sc->sc_config_td, &aue_config_copy,
				    &aue_cfg_promisc_upd, 0, 0);
			} else {
				usb2_config_td_queue_command
				    (&sc->sc_config_td, &aue_cfg_pre_init,
				    &aue_cfg_init, 0, 0);
			}
		} else {
			if (ifp->if_drv_flags & IFF_DRV_RUNNING) {
				usb2_config_td_queue_command
				    (&sc->sc_config_td, &aue_cfg_pre_stop,
				    &aue_cfg_stop, 0, 0);
			}
		}
		mtx_unlock(&sc->sc_mtx);
		break;

	case SIOCADDMULTI:
	case SIOCDELMULTI:
		mtx_lock(&sc->sc_mtx);
		usb2_config_td_queue_command
		    (&sc->sc_config_td, &aue_config_copy,
		    &aue_cfg_setmulti, 0, 0);
		mtx_unlock(&sc->sc_mtx);
		break;

	case SIOCGIFMEDIA:
	case SIOCSIFMEDIA:
		mii = GET_MII(sc);
		if (mii == NULL) {
			error = EINVAL;
		} else {
			error = ifmedia_ioctl
			    (ifp, (void *)data, &mii->mii_media, command);
		}
		break;

	default:
		error = ether_ioctl(ifp, command, data);
		break;
	}
	return (error);
}

static void
aue_watchdog(void *arg)
{
	struct aue_softc *sc = arg;

	mtx_assert(&sc->sc_mtx, MA_OWNED);

	usb2_config_td_queue_command
	    (&sc->sc_config_td, NULL, &aue_cfg_tick, 0, 0);

	usb2_callout_reset(&sc->sc_watchdog,
	    hz, &aue_watchdog, sc);

	mtx_unlock(&sc->sc_mtx);
	return;
}

/*
 * Stop the adapter and free any mbufs allocated to the
 * RX and TX lists.
 *
 * NOTE: can be called when "ifp" is NULL
 */
static void
aue_cfg_pre_stop(struct aue_softc *sc,
    struct usb2_config_td_cc *cc, uint16_t refcount)
{
	struct ifnet *ifp = sc->sc_ifp;

	if (cc) {
		/* copy the needed configuration */
		aue_config_copy(sc, cc, refcount);
	}
	/* immediate configuration */

	if (ifp) {
		/* clear flags */
		ifp->if_drv_flags &= ~IFF_DRV_RUNNING;
	}
	sc->sc_flags &= ~(AUE_FLAG_HL_READY |
	    AUE_FLAG_LL_READY);

	sc->sc_flags |= AUE_FLAG_WAIT_LINK;

	/*
	 * stop all the transfers, if not already stopped:
	 */
	usb2_transfer_stop(sc->sc_xfer[0]);
	usb2_transfer_stop(sc->sc_xfer[1]);
	usb2_transfer_stop(sc->sc_xfer[2]);
	usb2_transfer_stop(sc->sc_xfer[3]);
	usb2_transfer_stop(sc->sc_xfer[4]);
	usb2_transfer_stop(sc->sc_xfer[5]);
	return;
}

static void
aue_cfg_stop(struct aue_softc *sc,
    struct usb2_config_td_cc *cc, uint16_t refcount)
{
	aue_cfg_csr_write_1(sc, AUE_CTL0, 0);
	aue_cfg_csr_write_1(sc, AUE_CTL1, 0);
	aue_cfg_reset(sc);
	return;
}

/*
 * Stop all chip I/O so that the kernel's probe routines don't
 * get confused by errant DMAs when rebooting.
 */
static int
aue_shutdown(device_t dev)
{
	struct aue_softc *sc = device_get_softc(dev);

	mtx_lock(&sc->sc_mtx);

	usb2_config_td_queue_command
	    (&sc->sc_config_td, &aue_cfg_pre_stop,
	    &aue_cfg_stop, 0, 0);

	mtx_unlock(&sc->sc_mtx);

	return (0);
}