645 lines
28 KiB
C
645 lines
28 KiB
C
|
/* $FreeBSD$ */
|
||
|
/*-
|
||
|
* Copyright (c) 2010 Lev Serebryakov <lev@FreeBSD.org>.
|
||
|
* All rights reserved.
|
||
|
*
|
||
|
* Redistribution and use in source and binary forms, with or without
|
||
|
* modification, are permitted provided that the following conditions
|
||
|
* are met:
|
||
|
* 1. Redistributions of source code must retain the above copyright
|
||
|
* notice, this list of conditions and the following disclaimer.
|
||
|
* 2. Redistributions in binary form must reproduce the above copyright
|
||
|
* notice, this list of conditions and the following disclaimer in the
|
||
|
* documentation and/or other materials provided with the distribution.
|
||
|
*
|
||
|
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
|
||
|
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
||
|
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
||
|
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
|
||
|
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
||
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
||
|
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
||
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
|
||
|
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
|
||
|
* SUCH DAMAGE.
|
||
|
*/
|
||
|
#ifndef _UMCS7840_H_
|
||
|
#define _UMCS7840_H_
|
||
|
|
||
|
#define UMCS7840_MAX_PORTS 4
|
||
|
|
||
|
#define UMCS7840_READ_LENGTH 1 /* bytes */
|
||
|
#define UMCS7840_CTRL_TIMEOUT 500 /* ms */
|
||
|
|
||
|
/* Read/Wrtire registers vendor commands */
|
||
|
#define MCS7840_RDREQ 0x0d
|
||
|
#define MCS7840_WRREQ 0x0e
|
||
|
|
||
|
/* Read/Wrtie EEPROM values */
|
||
|
#define MCS7840_EEPROM_RW_WVALUE 0x0900
|
||
|
|
||
|
/*
|
||
|
* All these registers are documented only in full datasheet,
|
||
|
* which can be requested from MosChip tech support.
|
||
|
*/
|
||
|
#define MCS7840_DEV_REG_SP1 0x00 /* Options for for UART 1, R/W */
|
||
|
#define MCS7840_DEV_REG_CONTROL1 0x01 /* Control bits for UART 1,
|
||
|
* R/W */
|
||
|
#define MCS7840_DEV_REG_PINPONGHIGH 0x02 /* High bits of ping-pong
|
||
|
* register, R/W */
|
||
|
#define MCS7840_DEV_REG_PINPONGLOW 0x03 /* Low bits of ping-pong
|
||
|
* register, R/W */
|
||
|
/* DCRx_1 Registers goes here (see below, they are documented) */
|
||
|
#define MCS7840_DEV_REG_GPIO 0x07 /* GPIO_0 and GPIO_1 bits,
|
||
|
* undocumented, see notes
|
||
|
* below R/W */
|
||
|
#define MCS7840_DEV_REG_SP2 0x08 /* Options for for UART 2, R/W */
|
||
|
#define MCS7840_DEV_REG_CONTROL2 0x09 /* Control bits for UART 2,
|
||
|
* R/W */
|
||
|
#define MCS7840_DEV_REG_SP3 0x0a /* Options for for UART 3, R/W */
|
||
|
#define MCS7840_DEV_REG_CONTROL3 0x0b /* Control bits for UART 3,
|
||
|
* R/W */
|
||
|
#define MCS7840_DEV_REG_SP4 0x0c /* Options for for UART 4, R/W */
|
||
|
#define MCS7840_DEV_REG_CONTROL4 0x0d /* Control bits for UART 4,
|
||
|
* R/W */
|
||
|
#define MCS7840_DEV_REG_PLL_DIV_M 0x0e /* Pre-diviedr for PLL, R/W */
|
||
|
#define MCS7840_DEV_REG_UNKNOWN1 0x0f /* NOT MENTIONED AND NOT USED */
|
||
|
#define MCS7840_DEV_REG_PLL_DIV_N 0x10 /* Loop divider for PLL, R/W */
|
||
|
#define MCS7840_DEV_REG_CLOCK_MUX 0x12 /* PLL input clock & Interrupt
|
||
|
* endpoint control, R/W */
|
||
|
#define MCS7840_DEV_REG_UNKNOWN2 0x11 /* NOT MENTIONED AND NOT USED */
|
||
|
#define MCS7840_DEV_REG_CLOCK_SELECT12 0x13 /* Clock source for ports 1 &
|
||
|
* 2, R/W */
|
||
|
#define MCS7840_DEV_REG_CLOCK_SELECT34 0x14 /* Clock source for ports 3 &
|
||
|
* 4, R/W */
|
||
|
#define MCS7840_DEV_REG_UNKNOWN3 0x15 /* NOT MENTIONED AND NOT USED */
|
||
|
/* DCRx_2-DCRx_4 Registers goes here (see below, they are documented) */
|
||
|
#define MCS7840_DEV_REG_UNKNOWN4 0x1f /* NOT MENTIONED AND NOT USED */
|
||
|
#define MCS7840_DEV_REG_UNKNOWN5 0x20 /* NOT MENTIONED AND NOT USED */
|
||
|
#define MCS7840_DEV_REG_UNKNOWN6 0x21 /* NOT MENTIONED AND NOT USED */
|
||
|
#define MCS7840_DEV_REG_UNKNOWN7 0x22 /* NOT MENTIONED AND NOT USED */
|
||
|
#define MCS7840_DEV_REG_UNKNOWN8 0x23 /* NOT MENTIONED AND NOT USED */
|
||
|
#define MCS7840_DEV_REG_UNKNOWN9 0x24 /* NOT MENTIONED AND NOT USED */
|
||
|
#define MCS7840_DEV_REG_UNKNOWNA 0x25 /* NOT MENTIONED AND NOT USED */
|
||
|
#define MCS7840_DEV_REG_UNKNOWNB 0x26 /* NOT MENTIONED AND NOT USED */
|
||
|
#define MCS7840_DEV_REG_UNKNOWNC 0x27 /* NOT MENTIONED AND NOT USED */
|
||
|
#define MCS7840_DEV_REG_UNKNOWND 0x28 /* NOT MENTIONED AND NOT USED */
|
||
|
#define MCS7840_DEV_REG_UNKNOWNE 0x29 /* NOT MENTIONED AND NOT USED */
|
||
|
#define MCS7840_DEV_REG_UNKNOWNF 0x2a /* NOT MENTIONED AND NOT USED */
|
||
|
#define MCS7840_DEV_REG_MODE 0x2b /* Hardware configuration,
|
||
|
* R/Only */
|
||
|
#define MCS7840_DEV_REG_SP1_ICG 0x2c /* Inter character gap
|
||
|
* configuration for Port 1,
|
||
|
* R/W */
|
||
|
#define MCS7840_DEV_REG_SP2_ICG 0x2d /* Inter character gap
|
||
|
* configuration for Port 2,
|
||
|
* R/W */
|
||
|
#define MCS7840_DEV_REG_SP3_ICG 0x2e /* Inter character gap
|
||
|
* configuration for Port 3,
|
||
|
* R/W */
|
||
|
#define MCS7840_DEV_REG_SP4_ICG 0x2f /* Inter character gap
|
||
|
* configuration for Port 4,
|
||
|
* R/W */
|
||
|
#define MCS7840_DEV_REG_RX_SAMPLING12 0x30 /* RX sampling for ports 1 &
|
||
|
* 2, R/W */
|
||
|
#define MCS7840_DEV_REG_RX_SAMPLING34 0x31 /* RX sampling for ports 3 &
|
||
|
* 4, R/W */
|
||
|
#define MCS7840_DEV_REG_BI_FIFO_STAT1 0x32 /* Bulk-In FIFO Stat for Port
|
||
|
* 1, contains number of
|
||
|
* availiable bytes, R/Only */
|
||
|
#define MCS7840_DEV_REG_BO_FIFO_STAT1 0x33 /* Bulk-out FIFO Stat for Port
|
||
|
* 1, contains number of
|
||
|
* availiable bytes, R/Only */
|
||
|
#define MCS7840_DEV_REG_BI_FIFO_STAT2 0x34 /* Bulk-In FIFO Stat for Port
|
||
|
* 2, contains number of
|
||
|
* availiable bytes, R/Only */
|
||
|
#define MCS7840_DEV_REG_BO_FIFO_STAT2 0x35 /* Bulk-out FIFO Stat for Port
|
||
|
* 2, contains number of
|
||
|
* availiable bytes, R/Only */
|
||
|
#define MCS7840_DEV_REG_BI_FIFO_STAT3 0x36 /* Bulk-In FIFO Stat for Port
|
||
|
* 3, contains number of
|
||
|
* availiable bytes, R/Only */
|
||
|
#define MCS7840_DEV_REG_BO_FIFO_STAT3 0x37 /* Bulk-out FIFO Stat for Port
|
||
|
* 3, contains number of
|
||
|
* availiable bytes, R/Only */
|
||
|
#define MCS7840_DEV_REG_BI_FIFO_STAT4 0x38 /* Bulk-In FIFO Stat for Port
|
||
|
* 4, contains number of
|
||
|
* availiable bytes, R/Only */
|
||
|
#define MCS7840_DEV_REG_BO_FIFO_STAT4 0x39 /* Bulk-out FIFO Stat for Port
|
||
|
* 4, contains number of
|
||
|
* availiable bytes, R/Only */
|
||
|
#define MCS7840_DEV_REG_ZERO_PERIOD1 0x3a /* Period between zero out
|
||
|
* frames for Port 1, R/W */
|
||
|
#define MCS7840_DEV_REG_ZERO_PERIOD2 0x3b /* Period between zero out
|
||
|
* frames for Port 1, R/W */
|
||
|
#define MCS7840_DEV_REG_ZERO_PERIOD3 0x3c /* Period between zero out
|
||
|
* frames for Port 1, R/W */
|
||
|
#define MCS7840_DEV_REG_ZERO_PERIOD4 0x3d /* Period between zero out
|
||
|
* frames for Port 1, R/W */
|
||
|
#define MCS7840_DEV_REG_ZERO_ENABLE 0x3e /* Enable/disable of zero out
|
||
|
* frames, R/W */
|
||
|
#define MCS7840_DEV_REG_THR_VAL_LOW1 0x3f /* Low 8 bits of threshhold
|
||
|
* value for Bulk-Out for Port
|
||
|
* 1, R/W */
|
||
|
#define MCS7840_DEV_REG_THR_VAL_HIGH1 0x40 /* High 1 bit of threshhold
|
||
|
* value for Bulk-Out and
|
||
|
* enable flag for Port 1, R/W */
|
||
|
#define MCS7840_DEV_REG_THR_VAL_LOW2 0x41 /* Low 8 bits of threshhold
|
||
|
* value for Bulk-Out for Port
|
||
|
* 2, R/W */
|
||
|
#define MCS7840_DEV_REG_THR_VAL_HIGH2 0x42 /* High 1 bit of threshhold
|
||
|
* value for Bulk-Out and
|
||
|
* enable flag for Port 2, R/W */
|
||
|
#define MCS7840_DEV_REG_THR_VAL_LOW3 0x43 /* Low 8 bits of threshhold
|
||
|
* value for Bulk-Out for Port
|
||
|
* 3, R/W */
|
||
|
#define MCS7840_DEV_REG_THR_VAL_HIGH3 0x44 /* High 1 bit of threshhold
|
||
|
* value for Bulk-Out and
|
||
|
* enable flag for Port 3, R/W */
|
||
|
#define MCS7840_DEV_REG_THR_VAL_LOW4 0x45 /* Low 8 bits of threshhold
|
||
|
* value for Bulk-Out for Port
|
||
|
* 4, R/W */
|
||
|
#define MCS7840_DEV_REG_THR_VAL_HIGH4 0x46 /* High 1 bit of threshhold
|
||
|
* value for Bulk-Out and
|
||
|
* enable flag for Port 4, R/W */
|
||
|
|
||
|
/* Bits for SPx registers */
|
||
|
#define MCS7840_DEV_SPx_LOOP_PIPES 0x01 /* Loop Bulk-Out FIFO to the
|
||
|
* Bulk-In FIFO, default = 0 */
|
||
|
#define MCS7840_DEV_SPx_SKIP_ERR_DATA 0x02 /* Drop data bytes from UART,
|
||
|
* which were recevied with
|
||
|
* errors, default = 0 */
|
||
|
#define MCS7840_DEV_SPx_RESET_OUT_FIFO 0x04 /* Reset Bulk-Out FIFO */
|
||
|
#define MCS7840_DEV_SPx_RESET_IN_FIFO 0x08 /* Reset Bulk-In FIFO */
|
||
|
#define MCS7840_DEV_SPx_CLOCK_MASK 0x70 /* Mask to extract Baud CLK
|
||
|
* source */
|
||
|
#define MCS7840_DEV_SPx_CLOCK_X1 0x00 /* CLK = 1.8432Mhz, max speed
|
||
|
* = 115200 bps, default */
|
||
|
#define MCS7840_DEV_SPx_CLOCK_X2 0x10 /* CLK = 3.6864Mhz, max speed
|
||
|
* = 230400 bps */
|
||
|
#define MCS7840_DEV_SPx_CLOCK_X35 0x20 /* CLK = 6.4512Mhz, max speed
|
||
|
* = 403200 bps */
|
||
|
#define MCS7840_DEV_SPx_CLOCK_X4 0x30 /* CLK = 7.3728Mhz, max speed
|
||
|
* = 460800 bps */
|
||
|
#define MCS7840_DEV_SPx_CLOCK_X7 0x40 /* CLK = 12.9024Mhz, max speed
|
||
|
* = 806400 bps */
|
||
|
#define MCS7840_DEV_SPx_CLOCK_X8 0x50 /* CLK = 14.7456Mhz, max speed
|
||
|
* = 921600 bps */
|
||
|
#define MCS7840_DEV_SPx_CLOCK_24MHZ 0x60 /* CLK = 24.0000Mhz, max speed
|
||
|
* = 1.5 Mbps */
|
||
|
#define MCS7840_DEV_SPx_CLOCK_48MHZ 0x70 /* CLK = 48.0000Mhz, max speed
|
||
|
* = 3.0 Mbps */
|
||
|
#define MCS7840_DEV_SPx_CLOCK_SHIFT 4 /* Value 0..7 can be shifted
|
||
|
* to get clock value */
|
||
|
#define MCS7840_DEV_SPx_UART_RESET 0x80 /* Reset UART */
|
||
|
|
||
|
/* Bits for CONTROLx registers */
|
||
|
#define MCS7840_DEV_CONTROLx_HWFC 0x01 /* Enable hardware flow
|
||
|
* control (when power
|
||
|
* down? It is unclear
|
||
|
* in documents),
|
||
|
* default = 0 */
|
||
|
#define MCS7840_DEV_CONTROLx_UNUNSED1 0x02 /* Reserved */
|
||
|
#define MCS7840_DEV_CONTROLx_CTS_ENABLE 0x04 /* CTS changes are
|
||
|
* translated to MSR,
|
||
|
* default = 0 */
|
||
|
#define MCS7840_DEV_CONTROLx_UNUSED2 0x08 /* Reserved for ports
|
||
|
* 2,3,4 */
|
||
|
#define MCS7840_DEV_CONTROL1_DRIVER_DONE 0x08 /* USB enumerating is
|
||
|
* finished, USB
|
||
|
* enumeration memory
|
||
|
* can be used as FIFOs */
|
||
|
#define MCS7840_DEV_CONTROLx_RX_NEGATE 0x10 /* Negate RX input,
|
||
|
* works for IrDA mode
|
||
|
* only, default = 0 */
|
||
|
#define MCS7840_DEV_CONTROLx_RX_DISABLE 0x20 /* Disable RX logic,
|
||
|
* works only for
|
||
|
* RS-232/RS-485 mode,
|
||
|
* default = 0 */
|
||
|
#define MCS7840_DEV_CONTROLx_FSM_CONTROL 0x40 /* Disable RX FSM when
|
||
|
* TX is in progress,
|
||
|
* works for IrDA mode
|
||
|
* only, default = 0 */
|
||
|
#define MCS7840_DEV_CONTROLx_UNUSED3 0x80 /* Reserved */
|
||
|
|
||
|
/*
|
||
|
* Bits for PINPONGx registers
|
||
|
* These registers control how often two input buffers
|
||
|
* for Bulk-In FIFOs are swapped. One of buffers is used
|
||
|
* for USB trnasfer, other for receiving data from UART.
|
||
|
* Exact meaning of 15 bit value in these registers is unknown
|
||
|
*/
|
||
|
#define MCS7840_DEV_PINPONGHIGH_MULT 128 /* Only 7 bits in PINPONGLOW
|
||
|
* register */
|
||
|
#define MCS7840_DEV_PINPONGLOW_BITS 7 /* Only 7 bits in PINPONGLOW
|
||
|
* register */
|
||
|
|
||
|
/*
|
||
|
* THIS ONE IS UNDOCUMENTED IN FULL DATASHEET, but e-mail from tech support
|
||
|
* confirms, that it is register for GPIO_0 and GPIO_1 data input/output.
|
||
|
* Chips has 2 GPIO, but first one (lower bit) MUST be used by device
|
||
|
* authors as "number of port" indicator, grounded (0) for two-port
|
||
|
* devices and pulled-up to 1 for 4-port devices.
|
||
|
*/
|
||
|
#define MCS7840_DEV_GPIO_4PORTS 0x01 /* Device has 4 ports
|
||
|
* configured */
|
||
|
#define MCS7840_DEV_GPIO_GPIO_0 0x01 /* The same as above */
|
||
|
#define MCS7840_DEV_GPIO_GPIO_1 0x02 /* GPIO_1 data */
|
||
|
|
||
|
/*
|
||
|
* Constants for PLL dividers
|
||
|
* Ouptut frequency of PLL is:
|
||
|
* Fout = (N/M) * Fin.
|
||
|
* Default PLL input frequency Fin is 12Mhz (on-chip).
|
||
|
*/
|
||
|
#define MCS7840_DEV_PLL_DIV_M_BITS 6 /* Number of useful bits for M
|
||
|
* divider */
|
||
|
#define MCS7840_DEV_PLL_DIV_M_MASK 0x3f /* Mask for M divider */
|
||
|
#define MCS7840_DEV_PLL_DIV_M_MIN 1 /* Minimum value for M, 0 is
|
||
|
* forbidden */
|
||
|
#define MCS7840_DEV_PLL_DIV_M_DEF 1 /* Default value for M */
|
||
|
#define MCS7840_DEV_PLL_DIV_M_MAX 63 /* Maximum value for M */
|
||
|
#define MCS7840_DEV_PLL_DIV_N_BITS 6 /* Number of useful bits for N
|
||
|
* divider */
|
||
|
#define MCS7840_DEV_PLL_DIV_N_MASK 0x3f /* Mask for N divider */
|
||
|
#define MCS7840_DEV_PLL_DIV_N_MIN 1 /* Minimum value for N, 0 is
|
||
|
* forbidden */
|
||
|
#define MCS7840_DEV_PLL_DIV_N_DEF 8 /* Default value for N */
|
||
|
#define MCS7840_DEV_PLL_DIV_N_MAX 63 /* Maximum value for N */
|
||
|
|
||
|
/* Bits for CLOCK_MUX register */
|
||
|
#define MCS7840_DEV_CLOCK_MUX_INPUTMASK 0x03 /* Mask to extract PLL clock
|
||
|
* input */
|
||
|
#define MCS7840_DEV_CLOCK_MUX_IN12MHZ 0x00 /* 12Mhz PLL input, default */
|
||
|
#define MCS7840_DEV_CLOCK_MUX_INEXTRN 0x01 /* External (device-depended)
|
||
|
* PLL input */
|
||
|
#define MCS7840_DEV_CLOCK_MUX_INRSV1 0x02 /* Reserved */
|
||
|
#define MCS7840_DEV_CLOCK_MUX_INRSV2 0x03 /* Reserved */
|
||
|
#define MCS7840_DEV_CLOCK_MUX_PLLHIGH 0x04 /* 0 = PLL Output is
|
||
|
* 20MHz-100MHz (default), 1 =
|
||
|
* 100MHz-300MHz range */
|
||
|
#define MCS7840_DEV_CLOCK_MUX_INTRFIFOS 0x08 /* Enable additional 8 bytes
|
||
|
* fro Interrupt USB pipe with
|
||
|
* USB FIFOs statuses, default
|
||
|
* = 0 */
|
||
|
#define MCS7840_DEV_CLOCK_MUX_RESERVED1 0x10 /* Unused */
|
||
|
#define MCS7840_DEV_CLOCK_MUX_RESERVED2 0x20 /* Unused */
|
||
|
#define MCS7840_DEV_CLOCK_MUX_RESERVED3 0x40 /* Unused */
|
||
|
#define MCS7840_DEV_CLOCK_MUX_RESERVED4 0x80 /* Unused */
|
||
|
|
||
|
/* Bits for CLOCK_SELECTxx registers */
|
||
|
#define MCS7840_DEV_CLOCK_SELECT1_MASK 0x07 /* Bits for port 1 in
|
||
|
* CLOCK_SELECT12 */
|
||
|
#define MCS7840_DEV_CLOCK_SELECT1_SHIFT 0 /* Shift for port 1in
|
||
|
* CLOCK_SELECT12 */
|
||
|
#define MCS7840_DEV_CLOCK_SELECT2_MASK 0x38 /* Bits for port 2 in
|
||
|
* CLOCK_SELECT12 */
|
||
|
#define MCS7840_DEV_CLOCK_SELECT2_SHIFT 3 /* Shift for port 2 in
|
||
|
* CLOCK_SELECT12 */
|
||
|
#define MCS7840_DEV_CLOCK_SELECT3_MASK 0x07 /* Bits for port 3 in
|
||
|
* CLOCK_SELECT23 */
|
||
|
#define MCS7840_DEV_CLOCK_SELECT3_SHIFT 0 /* Shift for port 3 in
|
||
|
* CLOCK_SELECT23 */
|
||
|
#define MCS7840_DEV_CLOCK_SELECT4_MASK 0x38 /* Bits for port 4 in
|
||
|
* CLOCK_SELECT23 */
|
||
|
#define MCS7840_DEV_CLOCK_SELECT4_SHIFT 3 /* Shift for port 4 in
|
||
|
* CLOCK_SELECT23 */
|
||
|
#define MCS7840_DEV_CLOCK_SELECT_STD 0x00 /* STANDARD baudrate derived
|
||
|
* from 96Mhz, default for all
|
||
|
* ports */
|
||
|
#define MCS7840_DEV_CLOCK_SELECT_30MHZ 0x01 /* 30Mhz */
|
||
|
#define MCS7840_DEV_CLOCK_SELECT_96MHZ 0x02 /* 96Mhz direct */
|
||
|
#define MCS7840_DEV_CLOCK_SELECT_120MHZ 0x03 /* 120Mhz */
|
||
|
#define MCS7840_DEV_CLOCK_SELECT_PLL 0x04 /* PLL output (see for M and N
|
||
|
* dividers) */
|
||
|
#define MCS7840_DEV_CLOCK_SELECT_EXT 0x05 /* External clock input
|
||
|
* (device-dependend) */
|
||
|
#define MCS7840_DEV_CLOCK_SELECT_RES1 0x06 /* Unused */
|
||
|
#define MCS7840_DEV_CLOCK_SELECT_RES2 0x07 /* Unused */
|
||
|
|
||
|
/* Bits for MODE register */
|
||
|
#define MCS7840_DEV_MODE_RESERVED1 0x01 /* Unused */
|
||
|
#define MCS7840_DEV_MODE_RESET 0x02 /* 0: RESET = Active High
|
||
|
* (default), 1: Reserved (?) */
|
||
|
#define MCS7840_DEV_MODE_SER_PRSNT 0x04 /* 0: Reserved, 1: Do not use
|
||
|
* hardocded values (default)
|
||
|
* (?) */
|
||
|
#define MCS7840_DEV_MODE_PLLBYPASS 0x08 /* 1: PLL output is bypassed,
|
||
|
* default = 0 */
|
||
|
#define MCS7840_DEV_MODE_PORBYPASS 0x10 /* 1: Power-On Reset is
|
||
|
* bypassed, default = 0 */
|
||
|
#define MCS7840_DEV_MODE_SELECT24S 0x20 /* 0: 4 Serial Ports / IrDA
|
||
|
* active, 1: 2 Serial Ports /
|
||
|
* IrDA active */
|
||
|
#define MCS7840_DEV_MODE_EEPROMWR 0x40 /* EEPROM write is enabled,
|
||
|
* default */
|
||
|
#define MCS7840_DEV_MODE_IRDA 0x80 /* IrDA mode is activated
|
||
|
* (could be turned on),
|
||
|
* default */
|
||
|
|
||
|
/* Bits for SPx ICG */
|
||
|
#define MCS7840_DEV_SPx_ICG_DEF 0x24 /* All 8 bits is used as
|
||
|
* number of BAUD clocks of
|
||
|
* pause */
|
||
|
|
||
|
/*
|
||
|
* Bits for RX_SAMPLINGxx registers
|
||
|
* These registers control when bit value will be sampled within
|
||
|
* the baud period.
|
||
|
* 0 is very beginning of period, 15 is very end, 7 is the middle.
|
||
|
*/
|
||
|
#define MCS7840_DEV_RX_SAMPLING1_MASK 0x0f /* Bits for port 1 in
|
||
|
* RX_SAMPLING12 */
|
||
|
#define MCS7840_DEV_RX_SAMPLING1_SHIFT 0 /* Shift for port 1in
|
||
|
* RX_SAMPLING12 */
|
||
|
#define MCS7840_DEV_RX_SAMPLING2_MASK 0xf0 /* Bits for port 2 in
|
||
|
* RX_SAMPLING12 */
|
||
|
#define MCS7840_DEV_RX_SAMPLING2_SHIFT 4 /* Shift for port 2 in
|
||
|
* RX_SAMPLING12 */
|
||
|
#define MCS7840_DEV_RX_SAMPLING3_MASK 0x0f /* Bits for port 3 in
|
||
|
* RX_SAMPLING23 */
|
||
|
#define MCS7840_DEV_RX_SAMPLING3_SHIFT 0 /* Shift for port 3 in
|
||
|
* RX_SAMPLING23 */
|
||
|
#define MCS7840_DEV_RX_SAMPLING4_MASK 0xf0 /* Bits for port 4 in
|
||
|
* RX_SAMPLING23 */
|
||
|
#define MCS7840_DEV_RX_SAMPLING4_SHIFT 4 /* Shift for port 4 in
|
||
|
* RX_SAMPLING23 */
|
||
|
#define MCS7840_DEV_RX_SAMPLINGx_MIN 0 /* Max for any RX Sampling */
|
||
|
#define MCS7840_DEV_RX_SAMPLINGx_DEF 7 /* Default for any RX
|
||
|
* Sampling, center of period */
|
||
|
#define MCS7840_DEV_RX_SAMPLINGx_MAX 15 /* Min for any RX Sampling */
|
||
|
|
||
|
/* Bits for ZERO_PERIODx */
|
||
|
#define MCS7840_DEV_ZERO_PERIODx_DEF 20 /* Number of Bulk-in requests
|
||
|
* befor sending zero-sized
|
||
|
* reply */
|
||
|
|
||
|
/* Bits for ZERO_ENABLE */
|
||
|
#define MCS7840_DEV_ZERO_ENABLE_PORT1 0x01 /* Enable of sending
|
||
|
* zero-sized replies for port
|
||
|
* 1, default */
|
||
|
#define MCS7840_DEV_ZERO_ENABLE_PORT2 0x02 /* Enable of sending
|
||
|
* zero-sized replies for port
|
||
|
* 2, default */
|
||
|
#define MCS7840_DEV_ZERO_ENABLE_PORT3 0x04 /* Enable of sending
|
||
|
* zero-sized replies for port
|
||
|
* 3, default */
|
||
|
#define MCS7840_DEV_ZERO_ENABLE_PORT4 0x08 /* Enable of sending
|
||
|
* zero-sized replies for port
|
||
|
* 4, default */
|
||
|
|
||
|
/* Bits for THR_VAL_HIGHx */
|
||
|
#define MCS7840_DEV_THR_VAL_HIGH_MASK 0x01 /* Only one bit is used */
|
||
|
#define MCS7840_DEV_THR_VAL_HIGH_MUL 256 /* This one bit is means "256" */
|
||
|
#define MCS7840_DEV_THR_VAL_HIGH_SHIFT 8 /* This one bit is means "256" */
|
||
|
#define MCS7840_DEV_THR_VAL_HIGH_ENABLE 0x80 /* Enable threshold */
|
||
|
|
||
|
/* These are documented in "public" datasheet */
|
||
|
#define MCS7840_DEV_REG_DCR0_1 0x04 /* Device contol register 0 for Port
|
||
|
* 1, R/W */
|
||
|
#define MCS7840_DEV_REG_DCR1_1 0x05 /* Device contol register 1 for Port
|
||
|
* 1, R/W */
|
||
|
#define MCS7840_DEV_REG_DCR2_1 0x06 /* Device contol register 2 for Port
|
||
|
* 1, R/W */
|
||
|
#define MCS7840_DEV_REG_DCR0_2 0x16 /* Device contol register 0 for Port
|
||
|
* 2, R/W */
|
||
|
#define MCS7840_DEV_REG_DCR1_2 0x17 /* Device contol register 1 for Port
|
||
|
* 2, R/W */
|
||
|
#define MCS7840_DEV_REG_DCR2_2 0x18 /* Device contol register 2 for Port
|
||
|
* 2, R/W */
|
||
|
#define MCS7840_DEV_REG_DCR0_3 0x19 /* Device contol register 0 for Port
|
||
|
* 3, R/W */
|
||
|
#define MCS7840_DEV_REG_DCR1_3 0x1a /* Device contol register 1 for Port
|
||
|
* 3, R/W */
|
||
|
#define MCS7840_DEV_REG_DCR2_3 0x1b /* Device contol register 2 for Port
|
||
|
* 3, R/W */
|
||
|
#define MCS7840_DEV_REG_DCR0_4 0x1c /* Device contol register 0 for Port
|
||
|
* 4, R/W */
|
||
|
#define MCS7840_DEV_REG_DCR1_4 0x1d /* Device contol register 1 for Port
|
||
|
* 4, R/W */
|
||
|
#define MCS7840_DEV_REG_DCR2_4 0x1e /* Device contol register 2 for Port
|
||
|
* 4, R/W */
|
||
|
|
||
|
/* Bits of DCR0 registers, documented in datasheet */
|
||
|
#define MCS7840_DEV_DCR0_PWRSAVE 0x01 /* Shutdown transiver
|
||
|
* when USB Suspend is
|
||
|
* engaged, default = 1 */
|
||
|
#define MCS7840_DEV_DCR0_RESERVED1 0x02 /* Unused */
|
||
|
#define MCS7840_DEV_DCR0_GPIO_MODE_MASK 0x0c /* GPIO Mode bits, WORKS
|
||
|
* ONLY FOR PORT 1 */
|
||
|
#define MCS7840_DEV_DCR0_GPIO_MODE_IN 0x00 /* GPIO Mode - Input
|
||
|
* (0b00), WORKS ONLY
|
||
|
* FOR PORT 1 */
|
||
|
#define MCS7840_DEV_DCR0_GPIO_MODE_OUT 0x08 /* GPIO Mode - Input
|
||
|
* (0b10), WORKS ONLY
|
||
|
* FOR PORT 1 */
|
||
|
#define MCS7840_DEV_DCR0_RTS_ACTIVE_HIGH 0x10 /* RTS Active is HIGH,
|
||
|
* default = 0 (low) */
|
||
|
#define MCS7840_DEV_DCR0_RTS_AUTO 0x20 /* RTS is controlled by
|
||
|
* state of TX buffer,
|
||
|
* default = 0
|
||
|
* (controlled by MCR) */
|
||
|
#define MCS7840_DEV_DCR0_IRDA 0x40 /* IrDA mode */
|
||
|
#define MCS7840_DEV_DCR0_RESERVED2 0x80 /* Unused */
|
||
|
|
||
|
/* Bits of DCR1 registers, documented in datasheet */
|
||
|
#define MCS7840_DEV_DCR1_GPIO_CURRENT_MASK 0x03 /* Mask to extract GPIO
|
||
|
* current value, WORKS
|
||
|
* ONLY FOR PORT 1 */
|
||
|
#define MCS7840_DEV_DCR1_GPIO_CURRENT_6MA 0x00 /* GPIO output current
|
||
|
* 6mA, WORKS ONLY FOR
|
||
|
* PORT 1 */
|
||
|
#define MCS7840_DEV_DCR1_GPIO_CURRENT_8MA 0x01 /* GPIO output current
|
||
|
* 8mA, defauilt, WORKS
|
||
|
* ONLY FOR PORT 1 */
|
||
|
#define MCS7840_DEV_DCR1_GPIO_CURRENT_10MA 0x02 /* GPIO output current
|
||
|
* 10mA, WORKS ONLY FOR
|
||
|
* PORT 1 */
|
||
|
#define MCS7840_DEV_DCR1_GPIO_CURRENT_12MA 0x03 /* GPIO output current
|
||
|
* 12mA, WORKS ONLY FOR
|
||
|
* PORT 1 */
|
||
|
#define MCS7840_DEV_DCR1_UART_CURRENT_MASK 0x0c /* Mask to extract UART
|
||
|
* signals current value */
|
||
|
#define MCS7840_DEV_DCR1_UART_CURRENT_6MA 0x00 /* UART output current
|
||
|
* 6mA */
|
||
|
#define MCS7840_DEV_DCR1_UART_CURRENT_8MA 0x04 /* UART output current
|
||
|
* 8mA, defauilt */
|
||
|
#define MCS7840_DEV_DCR1_UART_CURRENT_10MA 0x08 /* UART output current
|
||
|
* 10mA */
|
||
|
#define MCS7840_DEV_DCR1_UART_CURRENT_12MA 0x0c /* UART output current
|
||
|
* 12mA */
|
||
|
#define MCS7840_DEV_DCR1_WAKEUP_DISABLE 0x10 /* Disable Remote USB
|
||
|
* Wakeup */
|
||
|
#define MCS7840_DEV_DCR1_PLLPWRDOWN_DISABLE 0x20 /* Disable PLL power
|
||
|
* down when not needed,
|
||
|
* WORKS ONLY FOR PORT 1 */
|
||
|
#define MCS7840_DEV_DCR1_LONG_INTERRUPT 0x40 /* Enable 13 bytes of
|
||
|
* interrupt data, with
|
||
|
* FIFO statistics,
|
||
|
* WORKS ONLY FOR PORT 1 */
|
||
|
#define MCS7840_DEV_DCR1_RESERVED1 0x80 /* Unused */
|
||
|
|
||
|
/*
|
||
|
* Bits of DCR2 registers, documented in datasheet
|
||
|
* Wakeup will work only if DCR0_IRDA = 0 (RS-xxx mode) and
|
||
|
* DCR1_WAKEUP_DISABLE = 0 (wakeup enabled).
|
||
|
*/
|
||
|
#define MCS7840_DEV_DCR2_WAKEUP_CTS 0x01 /* Wakeup on CTS change,
|
||
|
* default = 0 */
|
||
|
#define MCS7840_DEV_DCR2_WAKEUP_DCD 0x02 /* Wakeup on DCD change,
|
||
|
* default = 0 */
|
||
|
#define MCS7840_DEV_DCR2_WAKEUP_RI 0x04 /* Wakeup on RI change,
|
||
|
* default = 1 */
|
||
|
#define MCS7840_DEV_DCR2_WAKEUP_DSR 0x08 /* Wakeup on DSR change,
|
||
|
* default = 0 */
|
||
|
#define MCS7840_DEV_DCR2_WAKEUP_RXD 0x10 /* Wakeup on RX Data change,
|
||
|
* default = 0 */
|
||
|
#define MCS7840_DEV_DCR2_WAKEUP_RESUME 0x20 /* Wakeup issues RESUME
|
||
|
* signal, DISCONNECT
|
||
|
* otherwise, default = 1 */
|
||
|
#define MCS7840_DEV_DCR2_RESERVED1 0x40 /* Unused */
|
||
|
#define MCS7840_DEV_DCR2_SHDN_POLARITY 0x80 /* 0: Pin 12 Active Low, 1:
|
||
|
* Pin 12 Active High, default
|
||
|
* = 0 */
|
||
|
|
||
|
/* Interrupt endpoint bytes & bits */
|
||
|
#define MCS7840_IEP_FIFO_STATUS_INDEX 5
|
||
|
/*
|
||
|
* Thesse can be calculated as "1 << portnumber" for Bulk-out and
|
||
|
* "1 << (portnumber+1)" for Bulk-in
|
||
|
*/
|
||
|
#define MCS7840_IEP_BO_PORT1_HASDATA 0x01
|
||
|
#define MCS7840_IEP_BI_PORT1_HASDATA 0x02
|
||
|
#define MCS7840_IEP_BO_PORT2_HASDATA 0x04
|
||
|
#define MCS7840_IEP_BI_PORT2_HASDATA 0x08
|
||
|
#define MCS7840_IEP_BO_PORT3_HASDATA 0x10
|
||
|
#define MCS7840_IEP_BI_PORT3_HASDATA 0x20
|
||
|
#define MCS7840_IEP_BO_PORT4_HASDATA 0x40
|
||
|
#define MCS7840_IEP_BI_PORT4_HASDATA 0x80
|
||
|
|
||
|
/* Documented UART registers (fully compatible with 16550 UART) */
|
||
|
#define MCS7840_UART_REG_THR 0x00 /* Transmitter Holding
|
||
|
* Register W/Only */
|
||
|
#define MCS7840_UART_REG_RHR 0x00 /* Receiver Holding Register
|
||
|
* R/Only */
|
||
|
#define MCS7840_UART_REG_IER 0x01 /* Interrupt enable register -
|
||
|
* R/W */
|
||
|
#define MCS7840_UART_REG_FCR 0x02 /* FIFO Control register -
|
||
|
* W/Only */
|
||
|
#define MCS7840_UART_REG_ISR 0x02 /* Interrupt Status Registter
|
||
|
* R/Only */
|
||
|
#define MCS7840_UART_REG_LCR 0x03 /* Line control register R/W */
|
||
|
#define MCS7840_UART_REG_MCR 0x04 /* Modem control register R/W */
|
||
|
#define MCS7840_UART_REG_LSR 0x05 /* Line status register R/Only */
|
||
|
#define MCS7840_UART_REG_MSR 0x06 /* Modem status register
|
||
|
* R/Only */
|
||
|
#define MCS7840_UART_REG_SCRATCHPAD 0x07 /* Scratch pad register */
|
||
|
|
||
|
#define MCS7840_UART_REG_DLL 0x00 /* Low bits of BAUD divider */
|
||
|
#define MCS7840_UART_REG_DLM 0x01 /* High bits of BAUD divider */
|
||
|
|
||
|
/* IER bits */
|
||
|
#define MCS7840_UART_IER_RXREADY 0x01 /* RX Ready interrumpt mask */
|
||
|
#define MCS7840_UART_IER_TXREADY 0x02 /* TX Ready interrumpt mask */
|
||
|
#define MCS7840_UART_IER_RXSTAT 0x04 /* RX Status interrumpt mask */
|
||
|
#define MCS7840_UART_IER_MODEM 0x08 /* Modem status change
|
||
|
* interrumpt mask */
|
||
|
#define MCS7840_UART_IER_SLEEP 0x10 /* SLEEP enable */
|
||
|
|
||
|
/* FCR bits */
|
||
|
#define MCS7840_UART_FCR_ENABLE 0x01 /* Enable FIFO */
|
||
|
#define MCS7840_UART_FCR_FLUSHRHR 0x02 /* Flush RHR and FIFO */
|
||
|
#define MCS7840_UART_FCR_FLUSHTHR 0x04 /* Flush THR and FIFO */
|
||
|
#define MCS7840_UART_FCR_RTLMASK 0xa0 /* Mask to select RHR
|
||
|
* Interrupt Trigger level */
|
||
|
#define MCS7840_UART_FCR_RTL_1_1 0x00 /* L1 = 1, L2 = 1 */
|
||
|
#define MCS7840_UART_FCR_RTL_1_4 0x40 /* L1 = 1, L2 = 4 */
|
||
|
#define MCS7840_UART_FCR_RTL_1_8 0x80 /* L1 = 1, L2 = 8 */
|
||
|
#define MCS7840_UART_FCR_RTL_1_14 0xa0 /* L1 = 1, L2 = 14 */
|
||
|
|
||
|
/* ISR bits */
|
||
|
#define MCS7840_UART_ISR_NOPENDING 0x01 /* No interrupt pending */
|
||
|
#define MCS7840_UART_ISR_INTMASK 0x3f /* Mask to select interrupt
|
||
|
* source */
|
||
|
#define MCS7840_UART_ISR_RXERR 0x06 /* Recevir error */
|
||
|
#define MCS7840_UART_ISR_RXHASDATA 0x04 /* Recevier has data */
|
||
|
#define MCS7840_UART_ISR_RXTIMEOUT 0x0c /* Recevier timeout */
|
||
|
#define MCS7840_UART_ISR_TXEMPTY 0x02 /* Transmitter empty */
|
||
|
#define MCS7840_UART_ISR_MSCHANGE 0x00 /* Modem status change */
|
||
|
|
||
|
/* LCR bits */
|
||
|
#define MCS7840_UART_LCR_DATALENMASK 0x03 /* Mask for data length */
|
||
|
#define MCS7840_UART_LCR_DATALEN5 0x00 /* 5 data bits */
|
||
|
#define MCS7840_UART_LCR_DATALEN6 0x01 /* 6 data bits */
|
||
|
#define MCS7840_UART_LCR_DATALEN7 0x02 /* 7 data bits */
|
||
|
#define MCS7840_UART_LCR_DATALEN8 0x03 /* 8 data bits */
|
||
|
|
||
|
#define MCS7840_UART_LCR_STOPBMASK 0x04 /* Mask for stop bits */
|
||
|
#define MCS7840_UART_LCR_STOPB1 0x00 /* 1 stop bit in any case */
|
||
|
#define MCS7840_UART_LCR_STOPB2 0x04 /* 1.5-2 stop bits depends on
|
||
|
* data length */
|
||
|
|
||
|
#define MCS7840_UART_LCR_PARITYMASK 0x38 /* Mask for all parity data */
|
||
|
#define MCS7840_UART_LCR_PARITYON 0x08 /* Parity ON/OFF - ON */
|
||
|
#define MCS7840_UART_LCR_PARITYODD 0x00 /* Parity Odd */
|
||
|
#define MCS7840_UART_LCR_PARITYEVEN 0x10 /* Parity Even */
|
||
|
#define MCS7840_UART_LCR_PARITYODD 0x00 /* Parity Odd */
|
||
|
#define MCS7840_UART_LCR_PARITYFORCE 0x20 /* Force parity odd/even */
|
||
|
|
||
|
#define MCS7840_UART_LCR_BREAK 0x40 /* Send BREAK */
|
||
|
#define MCS7840_UART_LCR_DIVISORS 0x80 /* Map DLL/DLM instead of
|
||
|
* xHR/IER */
|
||
|
|
||
|
/* LSR bits */
|
||
|
#define MCS7840_UART_LSR_RHRAVAIL 0x01 /* Data available for read */
|
||
|
#define MCS7840_UART_LSR_RHROVERRUN 0x02 /* Data FIFO/register overflow */
|
||
|
#define MCS7840_UART_LSR_PARITYERR 0x04 /* Parity error */
|
||
|
#define MCS7840_UART_LSR_FRAMEERR 0x10 /* Framing error */
|
||
|
#define MCS7840_UART_LSR_BREAKERR 0x20 /* BREAK sigmal received */
|
||
|
#define MCS7840_UART_LSR_THREMPTY 0x40 /* THR register is empty,
|
||
|
* ready for transmit */
|
||
|
#define MCS7840_UART_LSR_HASERR 0x80 /* Has error in receiver FIFO */
|
||
|
|
||
|
/* MCR bits */
|
||
|
#define MCS7840_UART_MCR_DTR 0x01 /* Force DTR to be active
|
||
|
* (low) */
|
||
|
#define MCS7840_UART_MCR_RTS 0x02 /* Force RTS to be active
|
||
|
* (low) */
|
||
|
#define MCS7840_UART_MCR_IE 0x04 /* Enable interrupts (from
|
||
|
* code, not documented) */
|
||
|
#define MCS7840_UART_MCR_LOOPBACK 0x10 /* Enable local loopback test
|
||
|
* mode */
|
||
|
#define MCS7840_UART_MCR_CTSRTS 0x20 /* Enable CTS/RTS flow control
|
||
|
* in 550 (FIFO) mode */
|
||
|
#define MCS7840_UART_MCR_DTRDSR 0x40 /* Enable DTR/DSR flow control
|
||
|
* in 550 (FIFO) mode */
|
||
|
#define MCS7840_UART_MCR_DCD 0x80 /* Enable DCD flow control in
|
||
|
* 550 (FIFO) mode */
|
||
|
|
||
|
/* MSR bits */
|
||
|
#define MCS7840_UART_MSR_DELTACTS 0x01 /* CTS was changed since last
|
||
|
* read */
|
||
|
#define MCS7840_UART_MSR_DELTADSR 0x02 /* DSR was changed since last
|
||
|
* read */
|
||
|
#define MCS7840_UART_MSR_DELTARI 0x04 /* RI was changed from low to
|
||
|
* high since last read */
|
||
|
#define MCS7840_UART_MSR_DELTADCD 0x08 /* DCD was changed since last
|
||
|
* read */
|
||
|
#define MCS7840_UART_MSR_NEGCTS 0x10 /* Negated CTS signal */
|
||
|
#define MCS7840_UART_MSR_NEGDSR 0x20 /* Negated DSR signal */
|
||
|
#define MCS7840_UART_MSR_NEGRI 0x40 /* Negated RI signal */
|
||
|
#define MCS7840_UART_MSR_NEGDCD 0x80 /* Negated DCD signal */
|
||
|
|
||
|
/* SCRATCHPAD bits */
|
||
|
#define MCS7840_UART_SCRATCHPAD_RS232 0x00 /* RS-485 disabled */
|
||
|
#define MCS7840_UART_SCRATCHPAD_RS485_DTRRX 0x80 /* RS-485 mode, DTR High
|
||
|
* = RX */
|
||
|
#define MCS7840_UART_SCRATCHPAD_RS485_DTRTX 0xc0 /* RS-485 mode, DTR High
|
||
|
* = TX */
|
||
|
|
||
|
#define MCS7840_CONFIG_INDEX 0
|
||
|
#define MCS7840_IFACE_INDEX 0
|
||
|
|
||
|
#endif
|