freebsd-dev/sys/dev/mii/bmtphyreg.h

175 lines
7.5 KiB
C
Raw Normal View History

/*-
* Copyright (c) 2001 The NetBSD Foundation, Inc.
* All rights reserved.
*
* This code is derived from software contributed to The NetBSD Foundation
* by Jason R. Thorpe.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
*
* THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
* TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
* PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
* from NetBSD: bmtphyreg.h,v 1.1 2001/06/02 21:42:10 thorpej Exp
*
* $FreeBSD$
*/
#ifndef _DEV_MII_BMTPHYREG_H_
#define _DEV_MII_BMTPHYREG_H_
/*
* BCM5201/BCM5202 registers.
*/
#define MII_BMTPHY_AUX_CTL 0x10 /* auxiliary control */
#define AUX_CTL_TXDIS 0x2000 /* transmitter disable */
#define AUX_CTL_4B5B_BYPASS 0x0400 /* bypass 4b5b encoder */
#define AUX_CTL_SCR_BYPASS 0x0200 /* bypass scrambler */
#define AUX_CTL_NRZI_BYPASS 0x0100 /* bypass NRZI encoder */
#define AUX_CTL_RXALIGN_BYPASS 0x0080 /* bypass rx symbol alignment */
#define AUX_CTL_BASEWANDER_DIS 0x0040 /* disable baseline wander correction */
#define AUX_CTL_FEF_EN 0x0020 /* far-end fault enable */
#define MII_BMTPHY_AUX_STS 0x11 /* auxiliary status */
#define AUX_STS_FX_MODE 0x0400 /* 100base-FX mode (strap pin) */
#define AUX_STS_LOCKED 0x0200 /* descrambler locked */
#define AUX_STS_100BASE_LINK 0x0100 /* 1 = 100base link */
#define AUX_STS_REMFAULT 0x0080 /* remote fault */
#define AUX_STS_DISCON_STATE 0x0040 /* disconnect state */
#define AUX_STS_FCARDET 0x0020 /* false carrier detected */
#define AUX_STS_BAD_ESD 0x0010 /* bad ESD detected */
#define AUX_STS_RXERROR 0x0008 /* Rx error detected */
#define AUX_STS_TXERROR 0x0004 /* Tx error detected */
#define AUX_STS_LOCKERROR 0x0002 /* lock error detected */
#define AUX_STS_MLT3ERROR 0x0001 /* MLT3 code error detected */
#define MII_BMTPHY_RXERROR_CTR 0x12 /* 100base-X Rx error counter */
#define RXERROR_CTR_MASK 0x00ff
#define MII_BMTPHY_FCS_CTR 0x13 /* 100base-X false carrier counter */
#define FCS_CTR_MASK 0x00ff
#define MII_BMTPHY_DIS_CTR 0x14 /* 100base-X disconnect counter */
#define DIS_CTR_MASK 0x00ff
#define MII_BMTPHY_PTEST 0x17 /* PTEST */
#define MII_BMTPHY_AUX_CSR 0x18 /* auxiliary control/status */
#define AUX_CSR_JABBER_DIS 0x8000 /* jabber disable */
#define AUX_CSR_FLINK 0x4000 /* force 10baseT link pass */
#define AUX_CSR_HSQ 0x0080 /* SQ high */
#define AUX_CSR_LSQ 0x0040 /* SQ low */
#define AUX_CSR_ER1 0x0020 /* edge rate 1 */
#define AUX_CSR_ER0 0x0010 /* edge rate 0 */
#define AUX_CSR_ANEG 0x0008 /* auto-negotiation activated */
#define AUX_CSR_F100 0x0004 /* force 100base */
#define AUX_CSR_SPEED 0x0002 /* 1 = 100, 0 = 10 */
#define AUX_CSR_FDX 0x0001 /* full-duplex */
#define MII_BMTPHY_AUX_SS 0x19 /* auxiliary status summary */
#define AUX_SS_ACOMP 0x8000 /* auto-negotiation complete */
#define AUX_SS_ACOMP_ACK 0x4000 /* auto-negotiation compl. ack */
#define AUX_SS_AACK_DET 0x2000 /* auto-neg. ack detected */
#define AUX_SS_ANLPAD 0x1000 /* auto-neg. link part. ability det */
#define AUX_SS_ANEG_PAUSE 0x0800 /* pause operation bit */
#define AUX_SS_HCD 0x0700 /* highest common denominator */
#define AUX_SS_HCD_NONE 0x0000 /* none */
#define AUX_SS_HCD_10T 0x0100 /* 10baseT */
#define AUX_SS_HCD_10T_FDX 0x0200 /* 10baseT-FDX */
#define AUX_SS_HCD_100TX 0x0300 /* 100baseTX-FDX */
#define AUX_SS_HCD_100T4 0x0400 /* 100baseT4 */
#define AUX_SS_HCD_100TX_FDX 0x0500 /* 100baseTX-FDX */
#define AUX_SS_PDF 0x0080 /* parallel detection fault */
#define AUX_SS_LPRF 0x0040 /* link partner remote fault */
#define AUX_SS_LPPR 0x0020 /* link partner page received */
#define AUX_SS_LPANA 0x0010 /* link partner auto-neg able */
#define AUX_SS_SPEED 0x0008 /* 1 = 100, 0 = 10 */
#define AUX_SS_LINK 0x0004 /* link pass */
#define AUX_SS_ANEN 0x0002 /* auto-neg. enabled */
#define AUX_SS_JABBER 0x0001 /* jabber detected */
#define MII_BMTPHY_INTR 0x1a /* interrupt register */
#define INTR_FDX_LED 0x8000 /* full-duplex led enable */
#define INTR_INTR_EN 0x4000 /* interrupt enable */
#define INTR_FDX_MASK 0x0800 /* full-dupled intr mask */
#define INTR_SPD_MASK 0x0400 /* speed intr mask */
#define INTR_LINK_MASK 0x0200 /* link intr mask */
#define INTR_INTR_MASK 0x0100 /* master interrupt mask */
#define INTR_FDX_CHANGE 0x0008 /* full-duplex change */
#define INTR_SPD_CHANGE 0x0004 /* speed change */
#define INTR_LINK_CHANGE 0x0002 /* link change */
#define INTR_INTR_STATUS 0x0001 /* interrupt status */
#define MII_BMTPHY_AUX2 0x1b /* auliliary mode 2 */
#define AUX2_BLOCK_RXDV 0x0200 /* block RXDV mode enabled */
#define AUX2_ANPDQ 0x0100 /* auto-neg parallel detection Q mode */
#define AUX2_TRAFFIC_LED 0x0040 /* traffic meter led enable */
#define AUX2_FXMTRCV_LED 0x0020 /* force Tx and Rx LEDs */
#define AUX2_HS_TOKEN 0x0010 /* high-speed token ring mode */
#define AUX2_AUTO_LP 0x0008 /* auto low-power mode */
#define AUX2_TWOLINK_LED 0x0004 /* two link LEDs */
#define AUX2_SQE_DIS 0x0002 /* disable SQE pulse */
#define MII_BMTPHY_AUXERR 0x1c /* auxiliary error */
#define AUXERR_MANCHESTER 0x0400 /* Manchester code error */
#define AUXERR_EOF 0x0200 /* EOF detection error */
#define AUXERR_POLARITY 0x0100 /* polarity inversion */
#define AUXERR_ANEG 0x0008 /* autonegotiation enabled */
#define AUXERR_F100 0x0004 /* force 100base */
#define AUXERR_SPEED 0x0002 /* 1 = 100, 0 = 10 */
#define AUXERR_FDX 0x0001 /* full-duplex */
#define MII_BMTPHY_AUXMODE 0x1d /* auxiliary mode */
#define AUXMODE_ACT_LED_DIS 0x0010 /* activity LED disable */
#define AUXMODE_LINK_LED_DIS 0x0008 /* link LED disable */
#define AUXMODE_BLOCK_TXEN 0x0002 /* enable block TXEN */
#define MII_BMTPHY_AUXMPHY 0x1e /* auxiliary multiple phy register */
#define AUXMPHY_HCD_TX_FDX 0x8000 /* res. is 100baseTX-FDX */
#define AUXMPHY_HCD_T4 0x4000 /* res. is 100baseT4 */
#define AUXMPHY_HCD_TX 0x2000 /* res. is 100baseTX */
#define AUXMPHY_HCD_10T_FDX 0x1000 /* res. is 10baseT-FDX */
#define AUXMPHY_HCD_10T 0x0800 /* res. is 10baseT */
#define AUXMPHY_RES_ANEG 0x0100 /* restart auto-negotiation */
#define AUXMPHY_ANEG_COMP 0x0080 /* auto-negotiation complete */
#define AUXMPHY_ACK_COMP 0x0040 /* acknowledge complete */
#define AUXMPHY_ACK_DET 0x0020 /* acknowledge detected */
#define AUXMPHY_ABILITY_DET 0x0010 /* waiting for LP ability */
#define AUXMPHY_SUPER_ISO 0x0008 /* super-isolate mode */
#define AUXMPHY_10T_SERIAL 0x0002 /* 10baseT serial mode */
#define MII_BMTPHY_TEST 0x1d /* Broadcom test register */
#endif /* _DEV_MII_BMTPHYREG_H_ */