freebsd-dev/sys/dev/ida/idareg.h

328 lines
10 KiB
C
Raw Normal View History

/*-
* Copyright (c) 1999,2000 Jonathan Lemon
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
1999-08-28 01:08:13 +00:00
* $FreeBSD$
*/
/*
* #defines and software structures for the Compaq RAID card
*/
/*
* defines for older EISA controllers (IDA, IDA-2, IAES, SMART)
*/
2004-01-13 11:28:21 +00:00
#define R_EISA_INT_MASK 0x01
#define R_EISA_LOCAL_MASK 0x04
#define R_EISA_LOCAL_DOORBELL 0x05
#define R_EISA_SYSTEM_MASK 0x06
#define R_EISA_SYSTEM_DOORBELL 0x07
#define R_EISA_LIST_ADDR 0x08
#define R_EISA_LIST_LEN 0x0c
#define R_EISA_TAG 0x0f
#define R_EISA_COMPLETE_ADDR 0x10
#define R_EISA_LIST_STATUS 0x16
2004-01-13 11:28:21 +00:00
#define EISA_CHANNEL_BUSY 0x01
#define EISA_CHANNEL_CLEAR 0x02
/*
* board register offsets for SMART-2 controllers
*/
2004-01-13 11:28:21 +00:00
#define R_CMD_FIFO 0x04
#define R_DONE_FIFO 0x08
#define R_INT_MASK 0x0C
#define R_STATUS 0x10
#define R_INT_PENDING 0x14
/*
* interrupt mask values for SMART series
*/
2004-01-13 11:28:21 +00:00
#define INT_DISABLE 0x00
#define INT_ENABLE 0x01
/*
* board offsets for the 42xx series
*/
2004-01-13 11:28:21 +00:00
#define R_42XX_STATUS 0x30
#define R_42XX_INT_MASK 0x34
#define R_42XX_REQUEST 0x40
#define R_42XX_REPLY 0x44
/*
* interrupt values for 42xx series
*/
2004-01-13 11:28:21 +00:00
#define INT_ENABLE_42XX 0x00
#define INT_DISABLE_42XX 0x08
#define STATUS_42XX_INT_PENDING 0x08
/*
* return status codes
*/
#define SOFT_ERROR 0x02 /* Non-fatal error. */
#define HARD_ERROR 0x04 /* Fatal error. */
#define INVALID_ERROR 0x10 /* Invalid Request Block. */
2004-01-13 11:28:21 +00:00
#define CMD_REJECTED 0x14
/*
2005-04-13 05:06:57 +00:00
* command types
*/
#define CMD_GET_LOG_DRV_INFO 0x10 /* Identify controller */
#define CMD_GET_CTRL_INFO 0x11 /* Identify logical driver */
#define CMD_SENSE_DRV_STATUS 0x12 /* Sense logical drive status */
#define CMD_START_RECOVERY 0x13 /* Start recover */
#define CMD_GET_PHYS_DRV_INFO 0x15 /* Identify physical drive */
#define CMD_BLINK_DRV_LEDS 0x16 /* Blink drive tray LEDs */
#define CMD_SENSE_DRV_LEDS 0x17 /* Sense Blinking drive tray LEDs */
#define CMD_GET_LOG_DRV_EXT 0x18 /* Identify logical drive, Extended */
#define CMD_READ 0x20 /* Read */
#define CMD_WRITE 0x30 /* Write */
#define CMD_WRITE_MEDIA 0x31 /* Write media */
#define CMD_RESET_CTRL 0x40 /* Reset controller */
#define CMD_DIAG_PASS_THRU 0x41 /* ??? */
#define CMD_GET_CONFIG 0x50 /* Sense configuration */
#define CMD_SET_CONFIG 0x51 /* Set configuration */
#define CMD_BYPASS_VOL_STATE 0x52 /* ??? */
#define CMD_SS_CREATE_VOL 0x53 /* ??? */
#define CMD_CHANGE_CONFIG 0x54 /* ??? */
#define CMD_SENSE_ORIG_CONF 0x55 /* ??? */
#define CMD_REORDER_LOG_DRV 0x56 /* ??? */
#define CMD_LABEL_LOG_DRV 0x57 /* Label logical drive */
#define CMD_SS_TO_VOL 0x58 /* ??? */
#define CMD_SET_SURFACE_DELAY 0x60 /* Set surface delay */
#define CMD_SET_OVERHEAT_DELAY 0x61 /* ??? */
#define CMD_SENSE_BUS_PARAMS 0x65 /* Sense bus parameters */
#define CMD_SENSE_SUBSYS_INFO 0x66 /* Sense Subsystem Information */
#define CMD_SENSE_SURFACE_ATS 0x70 /* Sense surface analysis task status */
#define CMD_PASSTHROUGH 0x90 /* Pass-through operation */
#define CMD_PASSTHROUGH_A 0x91 /* ??? */
#define CMD_RESET_SCSI_DEV 0x94 /* Reset SCSI device */
#define CMD_PAUSE_BG_ACT 0x98 /* Pause Background Activity */
#define CMD_RESUME_BG_ACT 0x99 /* Resume Background Activity */
#define CMD_START_FIRMWARE 0x99 /* for integrated RAID */
#define CMD_SENSE_DRV_ERR_LOG 0xa6 /* Sense drive error log */
#define CMD_START_CPM 0xa7 /* Start controller performance monitoring */
#define CMD_SENSE_CP 0xa8 /* Sense controller performance */
#define CMD_STOP_CPM 0xa9 /* Stop controller performance monitoring */
#define CMD_FLUSH_CACHE 0xc2 /* Flush/disable write cache */
#define CMD_COLLECT_BUFFER 0xd2 /* ??? */
#define CMD_ACCEPT_MEDIA_EXCH 0xe0 /* Accept Media Exchange */
#define CMD_FLASH_READ 0xf6 /* Read FLASH */
#define CMD_FLASH_WRITE 0xf7 /* Write FLASH */
/* logical drive parameter table */
struct ida_drive_param {
u_int16_t ncylinders;
u_int8_t nheads;
u_int8_t signature;
u_int8_t psectors;
u_int16_t wprecomp;
u_int8_t max_acc;
u_int8_t control;
u_int16_t pcylinders;
u_int8_t ptracks;
u_int16_t landing_zone;
u_int8_t nsectors;
u_int8_t checksum;
2002-09-23 18:54:32 +00:00
} __packed;
#define IDA_RAID0 0 /* No fault tolerance. */
#define IDA_RAID4 1 /* Data Guard */
#define IDA_RAID1 2 /* Mirroring */
#define IDA_RAID5 3 /* Distributed Data Guard */
/*
* CMD_GET_LOG_DRV_INFO (0x10)
* Identify Logical Drive
*/
struct ida_drive_info {
u_int16_t secsize; /* block size in bytes */
u_int32_t secperunit; /* blocks available */
struct ida_drive_param dp; /* logical drive parameter table */
u_int8_t mirror; /* fault tolerance */
u_int8_t reserved;
u_int8_t bios_disable;
2002-09-23 18:54:32 +00:00
} __packed;
/*
* CMD_GET_LOG_DRV_EXT (0x18)
* Identify Logical Drive, Extended
*/
struct ida_drive_info_ext {
u_int16_t secsize; /* block size in bytes */
u_int32_t secperunit; /* blocks available */
struct ida_drive_param dp; /* logical drive parameter table */
u_int8_t mirror; /* fault tolerance */
u_int8_t reserved;
u_int8_t bios_disable;
u_int32_t ld_id; /* Logical drive identifier */
u_int8_t ld_label[64]; /* Logical drive label */
} __packed;
/*
* CMD_GET_CTRL_INFO (0x11)
* Identify Controller
*/
struct ida_controller_info {
u_int8_t num_drvs; /* Number of configured logical drives */
u_int32_t signature; /* Configuration signature */
u_int8_t firm_rev[4]; /* ASCII firmware revision */
u_int8_t rom_rev[4]; /* ROM firmware revision */
u_int8_t hw_rev; /* Revision level of the hardware */
u_int32_t bb_rev;
u_int32_t dp_map; /* Drive present bit map */
u_int32_t ed_map; /* External drive bit map */
u_int32_t board_id;
u_int8_t cfg_error;
u_int32_t nd_map; /* Non-disk map */
u_int8_t bad_ram_addr;
u_int8_t cpu_rev;
u_int8_t pdpi_rev;
u_int8_t epic_rev;
u_int8_t wcxc_rev;
u_int8_t mkt_rev; /* Marketing revision */
u_int8_t cflag; /* Controller flags */
#define IDA_CI_CFLAG_7DPB (1<<3)
#define IDA_CI_CFLAG_BIGMAP (1<<7)
u_int8_t hflag;
u_int8_t expand_dis;
u_int8_t scsi_cc; /* SCSI chip count */
u_int32_t max_req_blocks;
u_int32_t cclock; /* Controller Clock */
u_int8_t dp_scsi; /* Drives per SCSI bus */
u_int16_t big_dp_map[8]; /* Big drive present bit map */
u_int16_t big_ed_map[8]; /* Big external drive bit map */
u_int16_t big_nd_map[8]; /* Big non-disk map */
u_int16_t task_flags;
u_int8_t icl_bus;
u_int8_t red_modes;
u_int8_t cur_red_mode;
u_int8_t red_ctlr_stat;
u_int8_t red_fail_reason;
u_int8_t reserved[403];
} __packed;
2005-04-13 05:06:57 +00:00
/*
* CMD_SENSE_DRV_STATUS (0x12)
* Sense logical drive status
*/
struct ida_drive_status {
u_int8_t status;
u_int32_t failure_map;
u_int16_t read_err[32];
u_int16_t write_error[32];
u_int8_t reserved0[288];
u_int32_t secrecover;
u_int8_t rebuilding;
u_int16_t remap_cnt[32];
u_int32_t repl_map;
u_int32_t spare_map;
u_int8_t spare_status;
u_int8_t spare_repl_map[32];
u_int32_t repl_ok_map;
u_int8_t media_exchange;
u_int8_t cache_failure;
u_int8_t expand_failure;
u_int8_t unit_flags;
u_int16_t big_failure_map[8];
u_int16_t big_remap_cnt[128];
u_int16_t big_repl_map[8];
u_int16_t big_act_spare_map[8];
u_int8_t big_spare_repl_map[128];
u_int16_t big_repl_ok_map[8];
u_int8_t big_rebuilding;
u_int8_t reserved1[36];
} __packed;
/*
* CMD_GET_PHYS_DRV_INFO (0x15)
* Identify Physical Drive
*/
struct ida_phys_drv_info {
u_int8_t scsi_bus; /* SCSI Bus */
u_int8_t scsi_id; /* SCSI ID */
u_int16_t blksize; /* block size in bytes */
u_int32_t blkcount; /* total blocks */
u_int32_t blkreserved; /* reserved blocks */
u_int8_t drv_model[40]; /* drive model */
u_int8_t drv_serial[40]; /* drive serial number */
u_int8_t drv_fwrev[8]; /* drive firmware revision */
u_int8_t scsi_inq; /* SCSI inquiry bits */
u_int8_t cpq_drv_stmp;
u_int8_t last_fail;
u_int8_t pd_flags; /* physical drive flags */
#define PDF_DISK_PRESENT 0x01
#define PDF_NONDISK_PRESENT 0x02
#define PDF_WIDE_ENABLED 0x04
#define PDF_SYNC 0x08
#define PDF_NARROW_TRAY 0x10
#define PDF_WIDEFAIL 0x20
#define PDF_ULTRA 0x40
#define PDF_ULTRA2 0x80
u_int8_t mpd_flags; /* more physical drive flags */
#define MPDF_SMART_SUPPORT 0x01 /* S.M.A.R.T supported */
#define MPDF_SMART_ERRORS 0x02 /* S.M.A.R.T errors recorded */
#define MPDF_SMART_ENABLED 0x04 /* S.M.A.R.T predictive failure is enabled */
#define MPDF_SMART_ERR_RESET 0x08 /* S.M.A.R.T errors recorded since last reset */
#define MPDF_DRIVE_EXTERNAL 0x10 /* Connected to external connector. */
#define MPDF_DRIVE_CONF_LVOL 0x20 /* Configured as part of a logical volume */
#define MPDF_DRIVE_CONF_SPARE 0x40 /* Configured as a spare */
#define MPDF_DRIVE_WCE 0x80 /* Drive WCE set on spinup */
u_int8_t scsi_lun;
u_int8_t ympd_flags; /* yet more physical drive flags */
#define YMPDF_DRIVE_WCE_SET 0x40 /* WCE currently set */
#define YMPDF_DRIVE_WCE_CHNG 0x80 /* WCE changable */
u_int8_t reserved;
u_int32_t spi_speed_rules;
u_int8_t phys_con[2]; /* Physical Connector */
u_int8_t phys_box; /* Physical Box on Bus */
u_int8_t phys_bay; /* Physical Bay in Box */
} __packed;
/*
* CMD_BLINK_DRV_LEDS (0x16)
* Blink Drive Tray LEDs
*
* CMD_SENSE_DRV_LEDS (0x17)
* Sense Blinking Drive Tray LEDs
*/
struct ida_blink_drv_leds {
u_int32_t bd; /* Blink duration (in 10ths sec) */
u_int32_t bte; /* Blink time elapsed (sense only) */
u_int8_t bse[256]; /* Blink/seek enable */
u_int8_t reserved1[248];
} __packed;
/*
* CMD_LABEL_LOG_DRV (0x57)
* Label Logical Drive
*/
struct ida_label_logical {
u_int32_t ld_id; /* Logical drive identifier */
u_int8_t ld_label[64]; /* Logical drive label */
2002-09-23 18:54:32 +00:00
} __packed;