d/freebsd-dev
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
df3ac04211
freebsd-dev/sys/dev/aic7xxx/aic79xx.c

10150 lines
275 KiB
C
Raw Normal View History

Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*
* Core routines and tables shareable across OS platforms.
*
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
* Copyright (c) 1994-2002 Justin T. Gibbs.
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
* Copyright (c) 2000-2003 Adaptec Inc.
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions, and the following disclaimer,
* without modification.
* 2. Redistributions in binary form must reproduce at minimum a disclaimer
* substantially similar to the "NO WARRANTY" disclaimer below
* ("Disclaimer") and any redistribution must be conditioned upon
* including a substantially similar Disclaimer requirement for further
* binary redistribution.
* 3. Neither the names of the above-listed copyright holders nor the names
* of any contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* Alternatively, this software may be distributed under the terms of the
* GNU General Public License ("GPL") version 2 as published by the Free
* Software Foundation.
*
* NO WARRANTY
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR
* A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
* HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
* IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGES.
*
In ahd_run_qoutfifos, correct a !=/== logic bug that would cause an infinite loop any time we manually flush the good status FIFO. Also make our loop delay unconditional to ensure we don't miss any FIFO allocations by the hardware.
2003-12-19 04:17:43 +00:00
* $Id: //depot/aic7xxx/aic7xxx/aic79xx.c#224 $
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
*/
#ifdef __linux__
#include "aic79xx_osm.h"
#include "aic79xx_inline.h"
#include "aicasm/aicasm_insformat.h"
#else
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
#include <sys/cdefs.h>
__FBSDID("$FreeBSD$");
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
#include <dev/aic7xxx/aic79xx_osm.h>
#include <dev/aic7xxx/aic79xx_inline.h>
#include <dev/aic7xxx/aicasm/aicasm_insformat.h>
#endif
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
/******************************** Globals *************************************/
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
struct ahd_softc_tailq ahd_tailq = TAILQ_HEAD_INITIALIZER(ahd_tailq);
/***************************** Lookup Tables **********************************/
char *ahd_chip_names[] =
{
"NONE",
"aic7901",
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
"aic7902",
"aic7901A"
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
};
static const u_int num_chip_names = NUM_ELEMENTS(ahd_chip_names);
/*
* Hardware error codes.
*/
struct ahd_hard_error_entry {
uint8_t errno;
char *errmesg;
};
static struct ahd_hard_error_entry ahd_hard_errors[] = {
{ DSCTMOUT, "Discard Timer has timed out" },
{ ILLOPCODE, "Illegal Opcode in sequencer program" },
{ SQPARERR, "Sequencer Parity Error" },
{ DPARERR, "Data-path Parity Error" },
{ MPARERR, "Scratch or SCB Memory Parity Error" },
{ CIOPARERR, "CIOBUS Parity Error" },
};
static const u_int num_errors = NUM_ELEMENTS(ahd_hard_errors);
static struct ahd_phase_table_entry ahd_phase_table[] =
{
{ P_DATAOUT, MSG_NOOP, "in Data-out phase" },
{ P_DATAIN, MSG_INITIATOR_DET_ERR, "in Data-in phase" },
{ P_DATAOUT_DT, MSG_NOOP, "in DT Data-out phase" },
{ P_DATAIN_DT, MSG_INITIATOR_DET_ERR, "in DT Data-in phase" },
{ P_COMMAND, MSG_NOOP, "in Command phase" },
{ P_MESGOUT, MSG_NOOP, "in Message-out phase" },
{ P_STATUS, MSG_INITIATOR_DET_ERR, "in Status phase" },
{ P_MESGIN, MSG_PARITY_ERROR, "in Message-in phase" },
{ P_BUSFREE, MSG_NOOP, "while idle" },
{ 0, MSG_NOOP, "in unknown phase" }
};
/*
* In most cases we only wish to itterate over real phases, so
* exclude the last element from the count.
*/
static const u_int num_phases = NUM_ELEMENTS(ahd_phase_table) - 1;
/* Our Sequencer Program */
#include "aic79xx_seq.h"
/**************************** Function Declarations ***************************/
static void ahd_handle_transmission_error(struct ahd_softc *ahd);
static void ahd_handle_lqiphase_error(struct ahd_softc *ahd,
u_int lqistat1);
static int ahd_handle_pkt_busfree(struct ahd_softc *ahd,
u_int busfreetime);
static int ahd_handle_nonpkt_busfree(struct ahd_softc *ahd);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
static void ahd_handle_proto_violation(struct ahd_softc *ahd);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
static void ahd_force_renegotiation(struct ahd_softc *ahd,
struct ahd_devinfo *devinfo);
static struct ahd_tmode_tstate*
ahd_alloc_tstate(struct ahd_softc *ahd,
u_int scsi_id, char channel);
#ifdef AHD_TARGET_MODE
static void ahd_free_tstate(struct ahd_softc *ahd,
u_int scsi_id, char channel, int force);
#endif
static void ahd_devlimited_syncrate(struct ahd_softc *ahd,
struct ahd_initiator_tinfo *,
u_int *period,
u_int *ppr_options,
role_t role);
static void ahd_update_neg_table(struct ahd_softc *ahd,
struct ahd_devinfo *devinfo,
struct ahd_transinfo *tinfo);
static void ahd_update_pending_scbs(struct ahd_softc *ahd);
static void ahd_fetch_devinfo(struct ahd_softc *ahd,
struct ahd_devinfo *devinfo);
static void ahd_scb_devinfo(struct ahd_softc *ahd,
struct ahd_devinfo *devinfo,
struct scb *scb);
static void ahd_setup_initiator_msgout(struct ahd_softc *ahd,
struct ahd_devinfo *devinfo,
struct scb *scb);
static void ahd_build_transfer_msg(struct ahd_softc *ahd,
struct ahd_devinfo *devinfo);
static void ahd_construct_sdtr(struct ahd_softc *ahd,
struct ahd_devinfo *devinfo,
u_int period, u_int offset);
static void ahd_construct_wdtr(struct ahd_softc *ahd,
struct ahd_devinfo *devinfo,
u_int bus_width);
static void ahd_construct_ppr(struct ahd_softc *ahd,
struct ahd_devinfo *devinfo,
u_int period, u_int offset,
u_int bus_width, u_int ppr_options);
static void ahd_clear_msg_state(struct ahd_softc *ahd);
static void ahd_handle_message_phase(struct ahd_softc *ahd);
typedef enum {
AHDMSG_1B,
AHDMSG_2B,
AHDMSG_EXT
} ahd_msgtype;
static int ahd_sent_msg(struct ahd_softc *ahd, ahd_msgtype type,
u_int msgval, int full);
static int ahd_parse_msg(struct ahd_softc *ahd,
struct ahd_devinfo *devinfo);
static int ahd_handle_msg_reject(struct ahd_softc *ahd,
struct ahd_devinfo *devinfo);
static void ahd_handle_ign_wide_residue(struct ahd_softc *ahd,
struct ahd_devinfo *devinfo);
static void ahd_reinitialize_dataptrs(struct ahd_softc *ahd);
static void ahd_handle_devreset(struct ahd_softc *ahd,
struct ahd_devinfo *devinfo,
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
u_int lun, cam_status status,
char *message, int verbose_level);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
#if AHD_TARGET_MODE
static void ahd_setup_target_msgin(struct ahd_softc *ahd,
struct ahd_devinfo *devinfo,
struct scb *scb);
#endif
Use better return types and a couple of casts to eliminate warnings on alpha. This will take the file out of sync with the private version that we maintain, but alpha tinderbox has been broken for too long. Tested on: i386, sparc64, alpha
2002-11-12 10:22:49 +00:00
static u_int ahd_sglist_size(struct ahd_softc *ahd);
static u_int ahd_sglist_allocsize(struct ahd_softc *ahd);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
static bus_dmamap_callback_t
ahd_dmamap_cb;
static void ahd_initialize_hscbs(struct ahd_softc *ahd);
static int ahd_init_scbdata(struct ahd_softc *ahd);
static void ahd_fini_scbdata(struct ahd_softc *ahd);
static void ahd_setup_iocell_workaround(struct ahd_softc *ahd);
static void ahd_iocell_first_selection(struct ahd_softc *ahd);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
static void ahd_add_col_list(struct ahd_softc *ahd,
struct scb *scb, u_int col_idx);
static void ahd_rem_col_list(struct ahd_softc *ahd,
struct scb *scb);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
static void ahd_chip_init(struct ahd_softc *ahd);
static void ahd_qinfifo_requeue(struct ahd_softc *ahd,
struct scb *prev_scb,
struct scb *scb);
static int ahd_qinfifo_count(struct ahd_softc *ahd);
static int ahd_search_scb_list(struct ahd_softc *ahd, int target,
char channel, int lun, u_int tag,
role_t role, uint32_t status,
ahd_search_action action,
u_int *list_head, u_int tid);
static void ahd_stitch_tid_list(struct ahd_softc *ahd,
u_int tid_prev, u_int tid_cur,
u_int tid_next);
static void ahd_add_scb_to_free_list(struct ahd_softc *ahd,
u_int scbid);
static u_int ahd_rem_wscb(struct ahd_softc *ahd, u_int scbid,
u_int prev, u_int next, u_int tid);
static void ahd_reset_current_bus(struct ahd_softc *ahd);
static ahd_callback_t ahd_reset_poll;
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
static ahd_callback_t ahd_stat_timer;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
#ifdef AHD_DUMP_SEQ
static void ahd_dumpseq(struct ahd_softc *ahd);
#endif
static void ahd_loadseq(struct ahd_softc *ahd);
static int ahd_check_patch(struct ahd_softc *ahd,
struct patch **start_patch,
u_int start_instr, u_int *skip_addr);
static u_int ahd_resolve_seqaddr(struct ahd_softc *ahd,
u_int address);
static void ahd_download_instr(struct ahd_softc *ahd,
u_int instrptr, uint8_t *dconsts);
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
static int ahd_probe_stack_size(struct ahd_softc *ahd);
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
static void ahd_other_scb_timeout(struct ahd_softc *ahd,
struct scb *scb,
struct scb *other_scb);
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
static int ahd_scb_active_in_fifo(struct ahd_softc *ahd,
struct scb *scb);
static void ahd_run_data_fifo(struct ahd_softc *ahd,
struct scb *scb);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
#ifdef AHD_TARGET_MODE
static void ahd_queue_lstate_event(struct ahd_softc *ahd,
struct ahd_tmode_lstate *lstate,
u_int initiator_id,
u_int event_type,
u_int event_arg);
static void ahd_update_scsiid(struct ahd_softc *ahd,
u_int targid_mask);
static int ahd_handle_target_cmd(struct ahd_softc *ahd,
struct target_cmd *cmd);
#endif
/******************************** Private Inlines *****************************/
static __inline void ahd_assert_atn(struct ahd_softc *ahd);
static __inline int ahd_currently_packetized(struct ahd_softc *ahd);
static __inline int ahd_set_active_fifo(struct ahd_softc *ahd);
static __inline void
ahd_assert_atn(struct ahd_softc *ahd)
{
ahd_outb(ahd, SCSISIGO, ATNO);
}
/*
* Determine if the current connection has a packetized
* agreement. This does not necessarily mean that we
* are currently in a packetized transfer. We could
* just as easily be sending or receiving a message.
*/
static __inline int
ahd_currently_packetized(struct ahd_softc *ahd)
{
ahd_mode_state saved_modes;
int packetized;
saved_modes = ahd_save_modes(ahd);
if ((ahd->bugs & AHD_PKTIZED_STATUS_BUG) != 0) {
/*
* The packetized bit refers to the last
* connection, not the current one. Check
* for non-zero LQISTATE instead.
*/
ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG);
packetized = ahd_inb(ahd, LQISTATE) != 0;
} else {
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
packetized = ahd_inb(ahd, LQISTAT2) & PACKETIZED;
}
ahd_restore_modes(ahd, saved_modes);
return (packetized);
}
static __inline int
ahd_set_active_fifo(struct ahd_softc *ahd)
{
u_int active_fifo;
AHD_ASSERT_MODES(ahd, AHD_MODE_SCSI_MSK, AHD_MODE_SCSI_MSK);
active_fifo = ahd_inb(ahd, DFFSTAT) & CURRFIFO;
switch (active_fifo) {
case 0:
case 1:
ahd_set_modes(ahd, active_fifo, active_fifo);
return (1);
default:
return (0);
}
}
/************************* Sequencer Execution Control ************************/
/*
* Restart the sequencer program from address zero
*/
void
ahd_restart(struct ahd_softc *ahd)
{
ahd_pause(ahd);
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
/* No more pending messages */
ahd_clear_msg_state(ahd);
ahd_outb(ahd, SCSISIGO, 0); /* De-assert BSY */
ahd_outb(ahd, MSG_OUT, MSG_NOOP); /* No message to send */
ahd_outb(ahd, SXFRCTL1, ahd_inb(ahd, SXFRCTL1) & ~BITBUCKET);
ahd_outb(ahd, SEQINTCTL, 0);
ahd_outb(ahd, LASTPHASE, P_BUSFREE);
ahd_outb(ahd, SEQ_FLAGS, 0);
ahd_outb(ahd, SAVED_SCSIID, 0xFF);
ahd_outb(ahd, SAVED_LUN, 0xFF);
/*
* Ensure that the sequencer's idea of TQINPOS
* matches our own. The sequencer increments TQINPOS
* only after it sees a DMA complete and a reset could
* occur before the increment leaving the kernel to believe
* the command arrived but the sequencer to not.
*/
ahd_outb(ahd, TQINPOS, ahd->tqinfifonext);
/* Always allow reselection */
ahd_outb(ahd, SCSISEQ1,
ahd_inb(ahd, SCSISEQ_TEMPLATE) & (ENSELI|ENRSELI|ENAUTOATNP));
ahd_set_modes(ahd, AHD_MODE_CCHAN, AHD_MODE_CCHAN);
ahd_outb(ahd, SEQCTL0, FASTMODE|SEQRESET);
ahd_unpause(ahd);
}
void
ahd_clear_fifo(struct ahd_softc *ahd, u_int fifo)
{
ahd_mode_state saved_modes;
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_FIFOS) != 0)
printf("%s: Clearing FIFO %d\n", ahd_name(ahd), fifo);
#endif
saved_modes = ahd_save_modes(ahd);
ahd_set_modes(ahd, fifo, fifo);
ahd_outb(ahd, DFFSXFRCTL, RSTCHN|CLRSHCNT);
if ((ahd_inb(ahd, SG_STATE) & FETCH_INPROG) != 0)
ahd_outb(ahd, CCSGCTL, CCSGRESET);
ahd_outb(ahd, LONGJMP_ADDR + 1, INVALID_ADDR);
ahd_outb(ahd, SG_STATE, 0);
ahd_restore_modes(ahd, saved_modes);
}
/************************* Input/Output Queues ********************************/
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
/*
* Flush and completed commands that are sitting in the command
* complete queues down on the chip but have yet to be dma'ed back up.
*/
void
ahd_flush_qoutfifo(struct ahd_softc *ahd)
{
struct scb *scb;
ahd_mode_state saved_modes;
u_int saved_scbptr;
u_int ccscbctl;
u_int scbid;
u_int next_scbid;
saved_modes = ahd_save_modes(ahd);
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
/*
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
* Flush the good status FIFO for completed packetized commands.
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
*/
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
saved_scbptr = ahd_get_scbptr(ahd);
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
while ((ahd_inb(ahd, LQISTAT2) & LQIGSAVAIL) != 0) {
u_int fifo_mode;
u_int i;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
scbid = ahd_inw(ahd, GSFIFO);
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
scb = ahd_lookup_scb(ahd, scbid);
if (scb == NULL) {
printf("%s: Warning - GSFIFO SCB %d invalid\n",
ahd_name(ahd), scbid);
continue;
}
/*
* Determine if this transaction is still active in
* any FIFO. If it is, we must flush that FIFO to
* the host before completing the command.
*/
fifo_mode = 0;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
rescan_fifos:
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
for (i = 0; i < 2; i++) {
/* Toggle to the other mode. */
fifo_mode ^= 1;
ahd_set_modes(ahd, fifo_mode, fifo_mode);
In ahd_run_qoutfifos, correct a !=/== logic bug that would cause an infinite loop any time we manually flush the good status FIFO. Also make our loop delay unconditional to ensure we don't miss any FIFO allocations by the hardware.
2003-12-19 04:17:43 +00:00
if (ahd_scb_active_in_fifo(ahd, scb) == 0)
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
continue;
ahd_run_data_fifo(ahd, scb);
/*
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
* Running this FIFO may cause a CFG4DATA for
* this same transaction to assert in the other
* FIFO or a new snapshot SAVEPTRS interrupt
* in this FIFO. Even running a FIFO may not
* clear the transaction if we are still waiting
* for data to drain to the host. We must loop
* until the transaction is not active in either
* FIFO just to be sure. Reset our loop counter
* so we will visit both FIFOs again before
In ahd_run_qoutfifos, correct a !=/== logic bug that would cause an infinite loop any time we manually flush the good status FIFO. Also make our loop delay unconditional to ensure we don't miss any FIFO allocations by the hardware.
2003-12-19 04:17:43 +00:00
* declaring this transaction finished. We
* also delay a bit so that status has a chance
* to change before we look at this FIFO again.
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
*/
In ahd_run_qoutfifos, correct a !=/== logic bug that would cause an infinite loop any time we manually flush the good status FIFO. Also make our loop delay unconditional to ensure we don't miss any FIFO allocations by the hardware.
2003-12-19 04:17:43 +00:00
aic_delay(200);
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
goto rescan_fifos;
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
}
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
ahd_set_scbptr(ahd, scbid);
if ((ahd_inb_scbram(ahd, SCB_SGPTR) & SG_LIST_NULL) == 0
&& ((ahd_inb_scbram(ahd, SCB_SGPTR) & SG_FULL_RESID) != 0
|| (ahd_inb_scbram(ahd, SCB_RESIDUAL_SGPTR)
& SG_LIST_NULL) != 0)) {
u_int comp_head;
/*
* The transfer completed with a residual.
* Place this SCB on the complete DMA list
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
* so that we update our in-core copy of the
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
* SCB before completing the command.
*/
ahd_outb(ahd, SCB_SCSI_STATUS, 0);
ahd_outb(ahd, SCB_SGPTR,
ahd_inb_scbram(ahd, SCB_SGPTR)
| SG_STATUS_VALID);
ahd_outw(ahd, SCB_TAG, SCB_GET_TAG(scb));
comp_head = ahd_inw(ahd, COMPLETE_DMA_SCB_HEAD);
ahd_outw(ahd, SCB_NEXT_COMPLETE, comp_head);
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
ahd_outw(ahd, COMPLETE_DMA_SCB_HEAD, SCB_GET_TAG(scb));
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
} else
ahd_complete_scb(ahd, scb);
}
ahd_set_scbptr(ahd, saved_scbptr);
/*
* Setup for command channel portion of flush.
*/
ahd_set_modes(ahd, AHD_MODE_CCHAN, AHD_MODE_CCHAN);
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
/*
* Wait for any inprogress DMA to complete and clear DMA state
* if this if for an SCB in the qinfifo.
*/
Add parenthesis so that we get all of the bits all of the contents of the CCSCBCTL register into our local varaible. The other bits are used in later tests. This avoids a potential deadlock in ahd_run_qoutfifo() if we happen to catch the DMA engine in just the right state.
2003-06-23 22:06:34 +00:00
while (((ccscbctl = ahd_inb(ahd, CCSCBCTL)) & (CCARREN|CCSCBEN)) != 0) {
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
if ((ccscbctl & (CCSCBDIR|CCARREN)) == (CCSCBDIR|CCARREN)) {
if ((ccscbctl & ARRDONE) != 0)
break;
} else if ((ccscbctl & CCSCBDONE) != 0)
break;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_delay(200);
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
}
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
/*
* We leave the sequencer to cleanup in the case of DMA's to
* update the qoutfifo. In all other cases (DMA's to the
* chip or a push of an SCB from the COMPLETE_DMA_SCB list),
* we disable the DMA engine so that the sequencer will not
* attempt to handle the DMA completion.
*/
if ((ccscbctl & CCSCBDIR) != 0 || (ccscbctl & ARRDONE) != 0)
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
ahd_outb(ahd, CCSCBCTL, ccscbctl & ~(CCARREN|CCSCBEN));
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
/*
* Complete any SCBs that just finished
* being DMA'ed into the qoutfifo.
*/
ahd_run_qoutfifo(ahd);
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
saved_scbptr = ahd_get_scbptr(ahd);
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
/*
* Manually update/complete any completed SCBs that are waiting to be
* DMA'ed back up to the host.
*/
scbid = ahd_inw(ahd, COMPLETE_DMA_SCB_HEAD);
while (!SCBID_IS_NULL(scbid)) {
uint8_t *hscb_ptr;
u_int i;
ahd_set_scbptr(ahd, scbid);
aic79xx.c: Include read streaming in the PPR flags we display in diagnostics. In ahd_reset(), set the known mode after our initial pause prior to setting the mode. We can't just set the mode directly because the current mode, after the pause, is most likely unknown and setting the mode when the saved mode is unknown will trigger an assertion in the mode debug code. Complete an audit for SCB RAM reads. These reads must be performed via the special ahd_in?_scbram() methods so we can perform a Rev A. PCI-X workaround. Remove a superfluous mode save operation that was performed just prior to a call to ahd_clear_critical_section(). The saved mode was never restored and wouldn't have been valid anyway since the mode could change while single stepping out of a critical section. aic79xx.h: Add new BUG definition AHD_PCIX_SCBRAM_RD_BUG. aic79xx_inline.h: Update ahd_inb_scbram routine to check for AHD_PCIX_SCBRAM_RD_BUG and only apply the workaround if this bug is active. The old code applied the workaround in all cases. aic79xx_pci.c: Set AHD_PCIX_SCBRAM_RD_BUG for the A4. Remove an attempted saved_modes call in ahd_pci_test_register_access(). Saving the modes can only occur when we are paused, but the call was happening before the chip was known to be paused. Restoring the modes doesn't make sense either since the code makes no assumptions about the state of the sequencer until the first time the mode is set by the driver. This happens after the registers are successfully mapped.
2003-03-06 23:58:34 +00:00
next_scbid = ahd_inw_scbram(ahd, SCB_NEXT_COMPLETE);
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
scb = ahd_lookup_scb(ahd, scbid);
if (scb == NULL) {
printf("%s: Warning - DMA-up and complete "
"SCB %d invalid\n", ahd_name(ahd), scbid);
continue;
}
hscb_ptr = (uint8_t *)scb->hscb;
for (i = 0; i < sizeof(struct hardware_scb); i++)
aic79xx.c: Include read streaming in the PPR flags we display in diagnostics. In ahd_reset(), set the known mode after our initial pause prior to setting the mode. We can't just set the mode directly because the current mode, after the pause, is most likely unknown and setting the mode when the saved mode is unknown will trigger an assertion in the mode debug code. Complete an audit for SCB RAM reads. These reads must be performed via the special ahd_in?_scbram() methods so we can perform a Rev A. PCI-X workaround. Remove a superfluous mode save operation that was performed just prior to a call to ahd_clear_critical_section(). The saved mode was never restored and wouldn't have been valid anyway since the mode could change while single stepping out of a critical section. aic79xx.h: Add new BUG definition AHD_PCIX_SCBRAM_RD_BUG. aic79xx_inline.h: Update ahd_inb_scbram routine to check for AHD_PCIX_SCBRAM_RD_BUG and only apply the workaround if this bug is active. The old code applied the workaround in all cases. aic79xx_pci.c: Set AHD_PCIX_SCBRAM_RD_BUG for the A4. Remove an attempted saved_modes call in ahd_pci_test_register_access(). Saving the modes can only occur when we are paused, but the call was happening before the chip was known to be paused. Restoring the modes doesn't make sense either since the code makes no assumptions about the state of the sequencer until the first time the mode is set by the driver. This happens after the registers are successfully mapped.
2003-03-06 23:58:34 +00:00
*hscb_ptr++ = ahd_inb_scbram(ahd, SCB_BASE + i);
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
ahd_complete_scb(ahd, scb);
scbid = next_scbid;
}
ahd_outw(ahd, COMPLETE_DMA_SCB_HEAD, SCB_LIST_NULL);
scbid = ahd_inw(ahd, COMPLETE_SCB_HEAD);
while (!SCBID_IS_NULL(scbid)) {
ahd_set_scbptr(ahd, scbid);
aic79xx.c: Include read streaming in the PPR flags we display in diagnostics. In ahd_reset(), set the known mode after our initial pause prior to setting the mode. We can't just set the mode directly because the current mode, after the pause, is most likely unknown and setting the mode when the saved mode is unknown will trigger an assertion in the mode debug code. Complete an audit for SCB RAM reads. These reads must be performed via the special ahd_in?_scbram() methods so we can perform a Rev A. PCI-X workaround. Remove a superfluous mode save operation that was performed just prior to a call to ahd_clear_critical_section(). The saved mode was never restored and wouldn't have been valid anyway since the mode could change while single stepping out of a critical section. aic79xx.h: Add new BUG definition AHD_PCIX_SCBRAM_RD_BUG. aic79xx_inline.h: Update ahd_inb_scbram routine to check for AHD_PCIX_SCBRAM_RD_BUG and only apply the workaround if this bug is active. The old code applied the workaround in all cases. aic79xx_pci.c: Set AHD_PCIX_SCBRAM_RD_BUG for the A4. Remove an attempted saved_modes call in ahd_pci_test_register_access(). Saving the modes can only occur when we are paused, but the call was happening before the chip was known to be paused. Restoring the modes doesn't make sense either since the code makes no assumptions about the state of the sequencer until the first time the mode is set by the driver. This happens after the registers are successfully mapped.
2003-03-06 23:58:34 +00:00
next_scbid = ahd_inw_scbram(ahd, SCB_NEXT_COMPLETE);
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
scb = ahd_lookup_scb(ahd, scbid);
if (scb == NULL) {
printf("%s: Warning - Complete SCB %d invalid\n",
ahd_name(ahd), scbid);
continue;
}
ahd_complete_scb(ahd, scb);
scbid = next_scbid;
}
ahd_outw(ahd, COMPLETE_SCB_HEAD, SCB_LIST_NULL);
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
/*
* Restore state.
*/
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
ahd_set_scbptr(ahd, saved_scbptr);
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
ahd_restore_modes(ahd, saved_modes);
ahd->flags |= AHD_UPDATE_PEND_CMDS;
}
/*
* Determine if an SCB for a packetized transaction
* is active in a FIFO.
*/
static int
ahd_scb_active_in_fifo(struct ahd_softc *ahd, struct scb *scb)
{
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
/*
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
* The FIFO is only active for our transaction if
* the SCBPTR matches the SCB's ID and the firmware
* has installed a handler for the FIFO or we have
* a pending SAVEPTRS or CFG4DATA interrupt.
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
*/
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
if (ahd_get_scbptr(ahd) != SCB_GET_TAG(scb)
|| ((ahd_inb(ahd, LONGJMP_ADDR+1) & INVALID_ADDR) != 0
&& (ahd_inb(ahd, SEQINTSRC) & (CFG4DATA|SAVEPTRS)) == 0))
return (0);
return (1);
}
/*
* Run a data fifo to completion for a transaction we know
* has completed across the SCSI bus (good status has been
* received). We are already set to the correct FIFO mode
* on entry to this routine.
*
* This function attempts to operate exactly as the firmware
* would when running this FIFO. Care must be taken to update
* this routine any time the firmware's FIFO algorithm is
* changed.
*/
static void
ahd_run_data_fifo(struct ahd_softc *ahd, struct scb *scb)
{
u_int seqintsrc;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
seqintsrc = ahd_inb(ahd, SEQINTSRC);
if ((seqintsrc & CFG4DATA) != 0) {
uint32_t datacnt;
uint32_t sgptr;
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
/*
* Clear full residual flag.
*/
sgptr = ahd_inl_scbram(ahd, SCB_SGPTR) & ~SG_FULL_RESID;
ahd_outb(ahd, SCB_SGPTR, sgptr);
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
/*
* Load datacnt and address.
*/
datacnt = ahd_inl_scbram(ahd, SCB_DATACNT);
if ((datacnt & AHD_DMA_LAST_SEG) != 0) {
sgptr |= LAST_SEG;
ahd_outb(ahd, SG_STATE, 0);
} else
ahd_outb(ahd, SG_STATE, LOADING_NEEDED);
ahd_outq(ahd, HADDR, ahd_inq_scbram(ahd, SCB_DATAPTR));
ahd_outl(ahd, HCNT, datacnt & AHD_SG_LEN_MASK);
ahd_outb(ahd, SG_CACHE_PRE, sgptr);
ahd_outb(ahd, DFCNTRL, PRELOADEN|SCSIEN|HDMAEN);
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
/*
* Initialize Residual Fields.
*/
ahd_outb(ahd, SCB_RESIDUAL_DATACNT+3, datacnt >> 24);
ahd_outl(ahd, SCB_RESIDUAL_SGPTR, sgptr & SG_PTR_MASK);
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
/*
* Mark the SCB as having a FIFO in use.
*/
ahd_outb(ahd, SCB_FIFO_USE_COUNT,
ahd_inb_scbram(ahd, SCB_FIFO_USE_COUNT) + 1);
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
/*
* Install a "fake" handler for this FIFO.
*/
ahd_outw(ahd, LONGJMP_ADDR, 0);
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
/*
* Notify the hardware that we have satisfied
* this sequencer interrupt.
*/
ahd_outb(ahd, CLRSEQINTSRC, CLRCFG4DATA);
} else if ((seqintsrc & SAVEPTRS) != 0) {
uint32_t sgptr;
uint32_t resid;
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
if ((ahd_inb(ahd, LONGJMP_ADDR+1)&INVALID_ADDR) != 0) {
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
/*
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
* Snapshot Save Pointers. All that
* is necessary to clear the snapshot
* is a CLRCHN.
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
*/
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
goto clrchn;
}
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
/*
* Disable S/G fetch so the DMA engine
* is available to future users.
*/
if ((ahd_inb(ahd, SG_STATE) & FETCH_INPROG) != 0)
ahd_outb(ahd, CCSGCTL, 0);
ahd_outb(ahd, SG_STATE, 0);
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
/*
* Flush the data FIFO. Strickly only
* necessary for Rev A parts.
*/
ahd_outb(ahd, DFCNTRL, ahd_inb(ahd, DFCNTRL) | FIFOFLUSH);
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
/*
* Calculate residual.
*/
sgptr = ahd_inl_scbram(ahd, SCB_RESIDUAL_SGPTR);
resid = ahd_inl(ahd, SHCNT);
resid |= ahd_inb_scbram(ahd, SCB_RESIDUAL_DATACNT+3) << 24;
ahd_outl(ahd, SCB_RESIDUAL_DATACNT, resid);
if ((ahd_inb(ahd, SG_CACHE_SHADOW) & LAST_SEG) == 0) {
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
/*
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
* Must back up to the correct S/G element.
* Typically this just means resetting our
* low byte to the offset in the SG_CACHE,
* but if we wrapped, we have to correct
* the other bytes of the sgptr too.
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
*/
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
if ((ahd_inb(ahd, SG_CACHE_SHADOW) & 0x80) != 0
&& (sgptr & 0x80) == 0)
sgptr -= 0x100;
sgptr &= ~0xFF;
sgptr |= ahd_inb(ahd, SG_CACHE_SHADOW)
& SG_ADDR_MASK;
ahd_outl(ahd, SCB_RESIDUAL_SGPTR, sgptr);
ahd_outb(ahd, SCB_RESIDUAL_DATACNT + 3, 0);
} else if ((resid & AHD_SG_LEN_MASK) == 0) {
ahd_outb(ahd, SCB_RESIDUAL_SGPTR,
sgptr | SG_LIST_NULL);
}
/*
* Save Pointers.
*/
ahd_outq(ahd, SCB_DATAPTR, ahd_inq(ahd, SHADDR));
ahd_outl(ahd, SCB_DATACNT, resid);
ahd_outl(ahd, SCB_SGPTR, sgptr);
ahd_outb(ahd, CLRSEQINTSRC, CLRSAVEPTRS);
ahd_outb(ahd, SEQIMODE,
ahd_inb(ahd, SEQIMODE) | ENSAVEPTRS);
/*
* If the data is to the SCSI bus, we are
* done, otherwise wait for FIFOEMP.
*/
if ((ahd_inb(ahd, DFCNTRL) & DIRECTION) != 0)
goto clrchn;
} else if ((ahd_inb(ahd, SG_STATE) & LOADING_NEEDED) != 0) {
uint32_t sgptr;
uint64_t data_addr;
uint32_t data_len;
u_int dfcntrl;
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
/*
* Disable S/G fetch so the DMA engine
* is available to future users. We won't
* be using the DMA engine to load segments.
*/
if ((ahd_inb(ahd, SG_STATE) & FETCH_INPROG) != 0) {
ahd_outb(ahd, CCSGCTL, 0);
ahd_outb(ahd, SG_STATE, LOADING_NEEDED);
}
/*
* Wait for the DMA engine to notice that the
* host transfer is enabled and that there is
* space in the S/G FIFO for new segments before
* loading more segments.
*/
if ((ahd_inb(ahd, DFSTATUS) & PRELOAD_AVAIL) != 0
&& (ahd_inb(ahd, DFCNTRL) & HDMAENACK) != 0) {
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
/*
* Determine the offset of the next S/G
* element to load.
*/
sgptr = ahd_inl_scbram(ahd, SCB_RESIDUAL_SGPTR);
sgptr &= SG_PTR_MASK;
if ((ahd->flags & AHD_64BIT_ADDRESSING) != 0) {
struct ahd_dma64_seg *sg;
sg = ahd_sg_bus_to_virt(ahd, scb, sgptr);
data_addr = sg->addr;
data_len = sg->len;
sgptr += sizeof(*sg);
} else {
struct ahd_dma_seg *sg;
sg = ahd_sg_bus_to_virt(ahd, scb, sgptr);
data_addr = sg->len & AHD_SG_HIGH_ADDR_MASK;
data_addr <<= 8;
data_addr |= sg->addr;
data_len = sg->len;
sgptr += sizeof(*sg);
}
/*
* Update residual information.
*/
ahd_outb(ahd, SCB_RESIDUAL_DATACNT+3, data_len >> 24);
ahd_outl(ahd, SCB_RESIDUAL_SGPTR, sgptr);
/*
* Load the S/G.
*/
if (data_len & AHD_DMA_LAST_SEG) {
sgptr |= LAST_SEG;
ahd_outb(ahd, SG_STATE, 0);
}
ahd_outq(ahd, HADDR, data_addr);
ahd_outl(ahd, HCNT, data_len & AHD_SG_LEN_MASK);
ahd_outb(ahd, SG_CACHE_PRE, sgptr & 0xFF);
/*
* Advertise the segment to the hardware.
*/
dfcntrl = ahd_inb(ahd, DFCNTRL)|PRELOADEN|HDMAEN;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
if ((ahd->features & AHD_NEW_DFCNTRL_OPTS) != 0) {
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
/*
* Use SCSIENWRDIS so that SCSIEN
* is never modified by this
* operation.
*/
dfcntrl |= SCSIENWRDIS;
}
ahd_outb(ahd, DFCNTRL, dfcntrl);
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
}
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
} else if ((ahd_inb(ahd, SG_CACHE_SHADOW) & LAST_SEG_DONE) != 0) {
/*
* Transfer completed to the end of SG list
* and has flushed to the host.
*/
ahd_outb(ahd, SCB_SGPTR,
ahd_inb_scbram(ahd, SCB_SGPTR) | SG_LIST_NULL);
goto clrchn;
} else if ((ahd_inb(ahd, DFSTATUS) & FIFOEMP) != 0) {
clrchn:
/*
* Clear any handler for this FIFO, decrement
* the FIFO use count for the SCB, and release
* the FIFO.
*/
ahd_outb(ahd, LONGJMP_ADDR + 1, INVALID_ADDR);
ahd_outb(ahd, SCB_FIFO_USE_COUNT,
ahd_inb_scbram(ahd, SCB_FIFO_USE_COUNT) - 1);
ahd_outb(ahd, DFFSXFRCTL, CLRCHN);
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
}
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
void
ahd_run_qoutfifo(struct ahd_softc *ahd)
{
struct scb *scb;
u_int scb_index;
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
if ((ahd->flags & AHD_RUNNING_QOUTFIFO) != 0)
panic("ahd_run_qoutfifo recursion");
ahd->flags |= AHD_RUNNING_QOUTFIFO;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_sync_qoutfifo(ahd, BUS_DMASYNC_POSTREAD);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
while ((ahd->qoutfifo[ahd->qoutfifonext]
& QOUTFIFO_ENTRY_VALID_LE) == ahd->qoutfifonext_valid_tag) {
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
scb_index = aic_le16toh(ahd->qoutfifo[ahd->qoutfifonext]
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
& ~QOUTFIFO_ENTRY_VALID_LE);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
scb = ahd_lookup_scb(ahd, scb_index);
if (scb == NULL) {
printf("%s: WARNING no command for scb %d "
"(cmdcmplt)\nQOUTPOS = %d\n",
ahd_name(ahd), scb_index,
ahd->qoutfifonext);
ahd_dump_card_state(ahd);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
} else
ahd_complete_scb(ahd, scb);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
ahd->qoutfifonext = (ahd->qoutfifonext+1) & (AHD_QOUT_SIZE-1);
if (ahd->qoutfifonext == 0)
ahd->qoutfifonext_valid_tag ^= QOUTFIFO_ENTRY_VALID_LE;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
ahd->flags &= ~AHD_RUNNING_QOUTFIFO;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
/************************* Interrupt Handling *********************************/
void
ahd_handle_hwerrint(struct ahd_softc *ahd)
{
/*
* Some catastrophic hardware error has occurred.
* Print it for the user and disable the controller.
*/
int i;
int error;
error = ahd_inb(ahd, ERROR);
for (i = 0; i < num_errors; i++) {
if ((error & ahd_hard_errors[i].errno) != 0)
printf("%s: hwerrint, %s\n",
ahd_name(ahd), ahd_hard_errors[i].errmesg);
}
ahd_dump_card_state(ahd);
panic("BRKADRINT");
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
/* Tell everyone that this HBA is no longer available */
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_abort_scbs(ahd, CAM_TARGET_WILDCARD, ALL_CHANNELS,
CAM_LUN_WILDCARD, SCB_LIST_NULL, ROLE_UNKNOWN,
CAM_NO_HBA);
/* Tell the system that this controller has gone away. */
ahd_free(ahd);
}
void
ahd_handle_seqint(struct ahd_softc *ahd, u_int intstat)
{
u_int seqintcode;
/*
* Save the sequencer interrupt code and clear the SEQINT
* bit. We will unpause the sequencer, if appropriate,
* after servicing the request.
*/
seqintcode = ahd_inb(ahd, SEQINTCODE);
ahd_outb(ahd, CLRINT, CLRSEQINT);
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
if ((ahd->bugs & AHD_INTCOLLISION_BUG) != 0) {
/*
* Unpause the sequencer and let it clear
* SEQINT by writing NO_SEQINT to it. This
* will cause the sequencer to be paused again,
* which is the expected state of this routine.
*/
ahd_unpause(ahd);
while (!ahd_is_paused(ahd))
;
ahd_outb(ahd, CLRINT, CLRSEQINT);
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_update_modes(ahd);
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_MISC) != 0)
printf("%s: Handle Seqint Called for code %d\n",
ahd_name(ahd), seqintcode);
#endif
switch (seqintcode) {
case ENTERING_NONPACK:
{
struct scb *scb;
u_int scbid;
AHD_ASSERT_MODES(ahd, ~(AHD_MODE_UNKNOWN_MSK|AHD_MODE_CFG_MSK),
~(AHD_MODE_UNKNOWN_MSK|AHD_MODE_CFG_MSK));
scbid = ahd_get_scbptr(ahd);
scb = ahd_lookup_scb(ahd, scbid);
if (scb == NULL) {
/*
* Somehow need to know if this
* is from a selection or reselection.
Correct a typo in a comment. Add a comment in ahd_clear_critical_sections() about our need to leave ENBUSFREE set in SIMODE1 while single stepping. Re-arrange some delay loops so that we always perform a read after any register write and before the delay. This should make the delay loop more accurate. When completing message processing for a packetized commention, return the controller to a state where invalid non-packetized phases will still cause protocol violations. These are the same operations as those performed in the clear_target_state routine in the firmware. Now that we have a chip with working ABORTPENDING support (the 7901B), comment out the automatic use of this feature until we can adequately test it. The previous checkin updated the bug mask for the 7901B so this code was exercised. When resetting the bus, perform an ahd_flush_device_writes() call so that our reset assertion delay is acurately timed from when the reset bit is written to the controller.
2003-06-28 04:42:11 +00:00
* From that, we can determine target
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
* ID so we at least have an I_T nexus.
*/
} else {
ahd_outb(ahd, SAVED_SCSIID, scb->hscb->scsiid);
ahd_outb(ahd, SAVED_LUN, scb->hscb->lun);
ahd_outb(ahd, SEQ_FLAGS, 0x0);
}
if ((ahd_inb(ahd, LQISTAT2) & LQIPHASE_OUTPKT) != 0
&& (ahd_inb(ahd, SCSISIGO) & ATNO) != 0) {
/*
* Phase change after read stream with
* CRC error with P0 asserted on last
* packet.
*/
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_RECOVERY) != 0)
printf("%s: Assuming LQIPHASE_NLQ with "
"P0 assertion\n", ahd_name(ahd));
#endif
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_RECOVERY) != 0)
printf("%s: Entering NONPACK\n", ahd_name(ahd));
#endif
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
break;
}
case INVALID_SEQINT:
printf("%s: Invalid Sequencer interrupt occurred.\n",
ahd_name(ahd));
ahd_dump_card_state(ahd);
ahd_reset_channel(ahd, 'A', /*Initiate Reset*/TRUE);
break;
case STATUS_OVERRUN:
{
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
struct scb *scb;
u_int scbid;
scbid = ahd_get_scbptr(ahd);
scb = ahd_lookup_scb(ahd, scbid);
if (scb != NULL)
ahd_print_path(ahd, scb);
else
printf("%s: ", ahd_name(ahd));
printf("SCB %d Packetized Status Overrun", scbid);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_dump_card_state(ahd);
ahd_reset_channel(ahd, 'A', /*Initiate Reset*/TRUE);
break;
}
case CFG4ISTAT_INTR:
{
struct scb *scb;
u_int scbid;
scbid = ahd_get_scbptr(ahd);
scb = ahd_lookup_scb(ahd, scbid);
if (scb == NULL) {
ahd_dump_card_state(ahd);
printf("CFG4ISTAT: Free SCB %d referenced", scbid);
panic("For safety");
}
ahd_outq(ahd, HADDR, scb->sense_busaddr);
ahd_outw(ahd, HCNT, AHD_SENSE_BUFSIZE);
ahd_outb(ahd, HCNT + 2, 0);
ahd_outb(ahd, SG_CACHE_PRE, SG_LAST_SEG);
ahd_outb(ahd, DFCNTRL, PRELOADEN|SCSIEN|HDMAEN);
break;
}
case ILLEGAL_PHASE:
{
u_int bus_phase;
bus_phase = ahd_inb(ahd, SCSISIGI) & PHASE_MASK;
printf("%s: ILLEGAL_PHASE 0x%x\n",
ahd_name(ahd), bus_phase);
switch (bus_phase) {
case P_DATAOUT:
case P_DATAIN:
case P_DATAOUT_DT:
case P_DATAIN_DT:
case P_MESGOUT:
case P_STATUS:
case P_MESGIN:
ahd_reset_channel(ahd, 'A', /*Initiate Reset*/TRUE);
printf("%s: Issued Bus Reset.\n", ahd_name(ahd));
break;
case P_COMMAND:
{
struct ahd_devinfo devinfo;
struct scb *scb;
struct ahd_initiator_tinfo *targ_info;
struct ahd_tmode_tstate *tstate;
struct ahd_transinfo *tinfo;
u_int scbid;
/*
* If a target takes us into the command phase
* assume that it has been externally reset and
* has thus lost our previous packetized negotiation
* agreement. Since we have not sent an identify
* message and may not have fully qualified the
* connection, we change our command to TUR, assert
* ATN and ABORT the task when we go to message in
* phase. The OSM will see the REQUEUE_REQUEST
* status and retry the command.
*/
scbid = ahd_get_scbptr(ahd);
scb = ahd_lookup_scb(ahd, scbid);
if (scb == NULL) {
printf("Invalid phase with no valid SCB. "
"Resetting bus.\n");
ahd_reset_channel(ahd, 'A',
/*Initiate Reset*/TRUE);
break;
}
ahd_compile_devinfo(&devinfo, SCB_GET_OUR_ID(scb),
SCB_GET_TARGET(ahd, scb),
SCB_GET_LUN(scb),
SCB_GET_CHANNEL(ahd, scb),
ROLE_INITIATOR);
targ_info = ahd_fetch_transinfo(ahd,
devinfo.channel,
devinfo.our_scsiid,
devinfo.target,
&tstate);
tinfo = &targ_info->curr;
ahd_set_width(ahd, &devinfo, MSG_EXT_WDTR_BUS_8_BIT,
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
AHD_TRANS_ACTIVE, /*paused*/TRUE);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_set_syncrate(ahd, &devinfo, /*period*/0,
/*offset*/0, /*ppr_options*/0,
AHD_TRANS_ACTIVE, /*paused*/TRUE);
ahd_outb(ahd, SCB_CDB_STORE, 0);
ahd_outb(ahd, SCB_CDB_STORE+1, 0);
ahd_outb(ahd, SCB_CDB_STORE+2, 0);
ahd_outb(ahd, SCB_CDB_STORE+3, 0);
ahd_outb(ahd, SCB_CDB_STORE+4, 0);
ahd_outb(ahd, SCB_CDB_STORE+5, 0);
ahd_outb(ahd, SCB_CDB_LEN, 6);
scb->hscb->control &= ~(TAG_ENB|SCB_TAG_TYPE);
scb->hscb->control |= MK_MESSAGE;
ahd_outb(ahd, SCB_CONTROL, scb->hscb->control);
ahd_outb(ahd, MSG_OUT, HOST_MSG);
ahd_outb(ahd, SAVED_SCSIID, scb->hscb->scsiid);
/*
* The lun is 0, regardless of the SCB's lun
* as we have not sent an identify message.
*/
ahd_outb(ahd, SAVED_LUN, 0);
ahd_outb(ahd, SEQ_FLAGS, 0);
ahd_assert_atn(ahd);
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
scb->flags &= ~SCB_PACKETIZED;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
scb->flags |= SCB_ABORT|SCB_CMDPHASE_ABORT;
ahd_freeze_devq(ahd, scb);
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_set_transaction_status(scb, CAM_REQUEUE_REQ);
aic_freeze_scb(scb);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*
* Allow the sequencer to continue with
* non-pack processing.
*/
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
ahd_outb(ahd, CLRLQOINT1, CLRLQOPHACHGINPKT);
if ((ahd->bugs & AHD_CLRLQO_AUTOCLR_BUG) != 0) {
ahd_outb(ahd, CLRLQOINT1, 0);
}
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_RECOVERY) != 0) {
ahd_print_path(ahd, scb);
printf("Unexpected command phase from "
"packetized target\n");
}
#endif
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
break;
}
}
break;
}
case CFG4OVERRUN:
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
{
struct scb *scb;
u_int scb_index;
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_RECOVERY) != 0) {
printf("%s: CFG4OVERRUN mode = %x\n", ahd_name(ahd),
ahd_inb(ahd, MODE_PTR));
}
#endif
scb_index = ahd_get_scbptr(ahd);
scb = ahd_lookup_scb(ahd, scb_index);
if (scb == NULL) {
/*
* Attempt to transfer to an SCB that is
* not outstanding.
*/
ahd_assert_atn(ahd);
ahd_outb(ahd, MSG_OUT, HOST_MSG);
ahd->msgout_buf[0] = MSG_ABORT_TASK;
ahd->msgout_len = 1;
ahd->msgout_index = 0;
ahd->msg_type = MSG_TYPE_INITIATOR_MSGOUT;
/*
* Clear status received flag to prevent any
* attempt to complete this bogus SCB.
*/
ahd_outb(ahd, SCB_CONTROL,
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
ahd_inb_scbram(ahd, SCB_CONTROL)
& ~STATUS_RCVD);
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
break;
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
case DUMP_CARD_STATE:
{
ahd_dump_card_state(ahd);
break;
}
case PDATA_REINIT:
{
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_RECOVERY) != 0) {
printf("%s: PDATA_REINIT - DFCNTRL = 0x%x "
"SG_CACHE_SHADOW = 0x%x\n",
ahd_name(ahd), ahd_inb(ahd, DFCNTRL),
ahd_inb(ahd, SG_CACHE_SHADOW));
}
#endif
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_reinitialize_dataptrs(ahd);
break;
}
case HOST_MSG_LOOP:
{
struct ahd_devinfo devinfo;
/*
* The sequencer has encountered a message phase
* that requires host assistance for completion.
* While handling the message phase(s), we will be
* notified by the sequencer after each byte is
* transfered so we can track bus phase changes.
*
* If this is the first time we've seen a HOST_MSG_LOOP
* interrupt, initialize the state of the host message
* loop.
*/
ahd_fetch_devinfo(ahd, &devinfo);
if (ahd->msg_type == MSG_TYPE_NONE) {
struct scb *scb;
u_int scb_index;
u_int bus_phase;
bus_phase = ahd_inb(ahd, SCSISIGI) & PHASE_MASK;
if (bus_phase != P_MESGIN
&& bus_phase != P_MESGOUT) {
printf("ahd_intr: HOST_MSG_LOOP bad "
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
"phase 0x%x\n", bus_phase);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*
* Probably transitioned to bus free before
* we got here. Just punt the message.
*/
ahd_dump_card_state(ahd);
ahd_clear_intstat(ahd);
ahd_restart(ahd);
return;
}
scb_index = ahd_get_scbptr(ahd);
scb = ahd_lookup_scb(ahd, scb_index);
if (devinfo.role == ROLE_INITIATOR) {
if (bus_phase == P_MESGOUT)
ahd_setup_initiator_msgout(ahd,
&devinfo,
scb);
else {
ahd->msg_type =
MSG_TYPE_INITIATOR_MSGIN;
ahd->msgin_index = 0;
}
}
#if AHD_TARGET_MODE
else {
if (bus_phase == P_MESGOUT) {
ahd->msg_type =
MSG_TYPE_TARGET_MSGOUT;
ahd->msgin_index = 0;
}
else
ahd_setup_target_msgin(ahd,
&devinfo,
scb);
}
#endif
}
ahd_handle_message_phase(ahd);
break;
}
case NO_MATCH:
{
/* Ensure we don't leave the selection hardware on */
AHD_ASSERT_MODES(ahd, AHD_MODE_SCSI_MSK, AHD_MODE_SCSI_MSK);
ahd_outb(ahd, SCSISEQ0, ahd_inb(ahd, SCSISEQ0) & ~ENSELO);
printf("%s:%c:%d: no active SCB for reconnecting "
"target - issuing BUS DEVICE RESET\n",
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
ahd_name(ahd), 'A', ahd_inb(ahd, SELID) >> 4);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
printf("SAVED_SCSIID == 0x%x, SAVED_LUN == 0x%x, "
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
"REG0 == 0x%x ACCUM = 0x%x\n",
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_inb(ahd, SAVED_SCSIID), ahd_inb(ahd, SAVED_LUN),
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
ahd_inw(ahd, REG0), ahd_inb(ahd, ACCUM));
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
printf("SEQ_FLAGS == 0x%x, SCBPTR == 0x%x, BTT == 0x%x, "
"SINDEX == 0x%x\n",
ahd_inb(ahd, SEQ_FLAGS), ahd_get_scbptr(ahd),
ahd_find_busy_tcl(ahd,
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
BUILD_TCL(ahd_inb(ahd, SAVED_SCSIID),
ahd_inb(ahd, SAVED_LUN))),
ahd_inw(ahd, SINDEX));
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
printf("SELID == 0x%x, SCB_SCSIID == 0x%x, SCB_LUN == 0x%x, "
"SCB_CONTROL == 0x%x\n",
ahd_inb(ahd, SELID), ahd_inb_scbram(ahd, SCB_SCSIID),
ahd_inb_scbram(ahd, SCB_LUN),
ahd_inb_scbram(ahd, SCB_CONTROL));
printf("SCSIBUS[0] == 0x%x, SCSISIGI == 0x%x\n",
ahd_inb(ahd, SCSIBUS), ahd_inb(ahd, SCSISIGI));
printf("SXFRCTL0 == 0x%x\n", ahd_inb(ahd, SXFRCTL0));
printf("SEQCTL0 == 0x%x\n", ahd_inb(ahd, SEQCTL0));
ahd_dump_card_state(ahd);
ahd->msgout_buf[0] = MSG_BUS_DEV_RESET;
ahd->msgout_len = 1;
ahd->msgout_index = 0;
ahd->msg_type = MSG_TYPE_INITIATOR_MSGOUT;
ahd_outb(ahd, MSG_OUT, HOST_MSG);
ahd_assert_atn(ahd);
break;
}
case PROTO_VIOLATION:
{
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
ahd_handle_proto_violation(ahd);
break;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
case IGN_WIDE_RES:
{
struct ahd_devinfo devinfo;
ahd_fetch_devinfo(ahd, &devinfo);
ahd_handle_ign_wide_residue(ahd, &devinfo);
break;
}
case BAD_PHASE:
{
u_int lastphase;
lastphase = ahd_inb(ahd, LASTPHASE);
printf("%s:%c:%d: unknown scsi bus phase %x, "
"lastphase = 0x%x. Attempting to continue\n",
ahd_name(ahd), 'A',
SCSIID_TARGET(ahd, ahd_inb(ahd, SAVED_SCSIID)),
lastphase, ahd_inb(ahd, SCSISIGI));
break;
}
case MISSED_BUSFREE:
{
u_int lastphase;
lastphase = ahd_inb(ahd, LASTPHASE);
printf("%s:%c:%d: Missed busfree. "
"Lastphase = 0x%x, Curphase = 0x%x\n",
ahd_name(ahd), 'A',
SCSIID_TARGET(ahd, ahd_inb(ahd, SAVED_SCSIID)),
lastphase, ahd_inb(ahd, SCSISIGI));
ahd_restart(ahd);
return;
}
case DATA_OVERRUN:
{
/*
* When the sequencer detects an overrun, it
* places the controller in "BITBUCKET" mode
* and allows the target to complete its transfer.
* Unfortunately, none of the counters get updated
* when the controller is in this mode, so we have
* no way of knowing how large the overrun was.
*/
struct scb *scb;
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
u_int scbindex;
#ifdef AHD_DEBUG
u_int lastphase;
#endif
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
scbindex = ahd_get_scbptr(ahd);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
scb = ahd_lookup_scb(ahd, scbindex);
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
#ifdef AHD_DEBUG
lastphase = ahd_inb(ahd, LASTPHASE);
if ((ahd_debug & AHD_SHOW_RECOVERY) != 0) {
ahd_print_path(ahd, scb);
printf("data overrun detected %s. Tag == 0x%x.\n",
ahd_lookup_phase_entry(lastphase)->phasemsg,
SCB_GET_TAG(scb));
ahd_print_path(ahd, scb);
printf("%s seen Data Phase. Length = %ld. "
"NumSGs = %d.\n",
ahd_inb(ahd, SEQ_FLAGS) & DPHASE
? "Have" : "Haven't",
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_get_transfer_length(scb), scb->sg_count);
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
ahd_dump_sglist(scb);
}
#endif
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*
* Set this and it will take effect when the
* target does a command complete.
*/
ahd_freeze_devq(ahd, scb);
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_set_transaction_status(scb, CAM_DATA_RUN_ERR);
aic_freeze_scb(scb);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
break;
}
case MKMSG_FAILED:
{
struct ahd_devinfo devinfo;
struct scb *scb;
u_int scbid;
ahd_fetch_devinfo(ahd, &devinfo);
printf("%s:%c:%d:%d: Attempt to issue message failed\n",
ahd_name(ahd), devinfo.channel, devinfo.target,
devinfo.lun);
scbid = ahd_get_scbptr(ahd);
scb = ahd_lookup_scb(ahd, scbid);
if (scb != NULL
&& (scb->flags & SCB_RECOVERY_SCB) != 0)
/*
* Ensure that we didn't put a second instance of this
* SCB into the QINFIFO.
*/
ahd_search_qinfifo(ahd, SCB_GET_TARGET(ahd, scb),
SCB_GET_CHANNEL(ahd, scb),
SCB_GET_LUN(scb), SCB_GET_TAG(scb),
ROLE_INITIATOR, /*status*/0,
SEARCH_REMOVE);
ahd_outb(ahd, SCB_CONTROL,
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
ahd_inb_scbram(ahd, SCB_CONTROL) & ~MK_MESSAGE);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
break;
}
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
case TASKMGMT_FUNC_COMPLETE:
{
u_int scbid;
struct scb *scb;
scbid = ahd_get_scbptr(ahd);
scb = ahd_lookup_scb(ahd, scbid);
if (scb != NULL) {
u_int lun;
u_int tag;
cam_status error;
ahd_print_path(ahd, scb);
printf("Task Management Func 0x%x Complete\n",
scb->hscb->task_management);
lun = CAM_LUN_WILDCARD;
tag = SCB_LIST_NULL;
switch (scb->hscb->task_management) {
case SIU_TASKMGMT_ABORT_TASK:
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
tag = SCB_GET_TAG(scb);
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
case SIU_TASKMGMT_ABORT_TASK_SET:
case SIU_TASKMGMT_CLEAR_TASK_SET:
lun = scb->hscb->lun;
error = CAM_REQ_ABORTED;
ahd_abort_scbs(ahd, SCB_GET_TARGET(ahd, scb),
'A', lun, tag, ROLE_INITIATOR,
error);
break;
case SIU_TASKMGMT_LUN_RESET:
lun = scb->hscb->lun;
case SIU_TASKMGMT_TARGET_RESET:
{
struct ahd_devinfo devinfo;
ahd_scb_devinfo(ahd, &devinfo, scb);
error = CAM_BDR_SENT;
ahd_handle_devreset(ahd, &devinfo, lun,
CAM_BDR_SENT,
lun != CAM_LUN_WILDCARD
? "Lun Reset"
: "Target Reset",
/*verbose_level*/0);
break;
}
default:
panic("Unexpected TaskMgmt Func\n");
break;
}
}
break;
}
case TASKMGMT_CMD_CMPLT_OKAY:
{
u_int scbid;
struct scb *scb;
/*
* An ABORT TASK TMF failed to be delivered before
* the targeted command completed normally.
*/
scbid = ahd_get_scbptr(ahd);
scb = ahd_lookup_scb(ahd, scbid);
if (scb != NULL) {
/*
* Remove the second instance of this SCB from
* the QINFIFO if it is still there.
*/
ahd_print_path(ahd, scb);
printf("SCB completes before TMF\n");
/*
* Handle losing the race. Wait until any
* current selection completes. We will then
* set the TMF back to zero in this SCB so that
* the sequencer doesn't bother to issue another
* sequencer interrupt for its completion.
*/
while ((ahd_inb(ahd, SCSISEQ0) & ENSELO) != 0
&& (ahd_inb(ahd, SSTAT0) & SELDO) == 0
&& (ahd_inb(ahd, SSTAT1) & SELTO) == 0)
;
ahd_outb(ahd, SCB_TASK_MANAGEMENT, 0);
ahd_search_qinfifo(ahd, SCB_GET_TARGET(ahd, scb),
SCB_GET_CHANNEL(ahd, scb),
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
SCB_GET_LUN(scb), SCB_GET_TAG(scb),
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
ROLE_INITIATOR, /*status*/0,
SEARCH_REMOVE);
}
break;
}
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
case TRACEPOINT0:
case TRACEPOINT1:
case TRACEPOINT2:
case TRACEPOINT3:
printf("%s: Tracepoint %d\n", ahd_name(ahd),
seqintcode - TRACEPOINT0);
break;
case NO_SEQINT:
break;
case SAW_HWERR:
ahd_handle_hwerrint(ahd);
break;
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
default:
printf("%s: Unexpected SEQINTCODE %d\n", ahd_name(ahd),
seqintcode);
break;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
/*
* The sequencer is paused immediately on
* a SEQINT, so we should restart it when
* we're done.
*/
ahd_unpause(ahd);
}
void
ahd_handle_scsiint(struct ahd_softc *ahd, u_int intstat)
{
struct scb *scb;
u_int status0;
u_int status3;
u_int status;
u_int lqistat1;
u_int lqostat0;
u_int scbid;
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
u_int busfreetime;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_update_modes(ahd);
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
status3 = ahd_inb(ahd, SSTAT3) & (NTRAMPERR|OSRAMPERR);
status0 = ahd_inb(ahd, SSTAT0) & (IOERR|OVERRUN|SELDI|SELDO);
status = ahd_inb(ahd, SSTAT1) & (SELTO|SCSIRSTI|BUSFREE|SCSIPERR);
lqistat1 = ahd_inb(ahd, LQISTAT1);
lqostat0 = ahd_inb(ahd, LQOSTAT0);
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
busfreetime = ahd_inb(ahd, SSTAT2) & BUSFREETIME;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if ((status0 & (SELDI|SELDO)) != 0) {
u_int simode0;
ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG);
simode0 = ahd_inb(ahd, SIMODE0);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
status0 &= simode0 & (IOERR|OVERRUN|SELDI|SELDO);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
}
scbid = ahd_get_scbptr(ahd);
scb = ahd_lookup_scb(ahd, scbid);
if (scb != NULL
&& (ahd_inb(ahd, SEQ_FLAGS) & NOT_IDENTIFIED) != 0)
scb = NULL;
/* Make sure the sequencer is in a safe location. */
ahd_clear_critical_section(ahd);
if ((status0 & IOERR) != 0) {
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
u_int now_lvd;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
now_lvd = ahd_inb(ahd, SBLKCTL) & ENAB40;
printf("%s: Transceiver State Has Changed to %s mode\n",
ahd_name(ahd), now_lvd ? "LVD" : "SE");
ahd_outb(ahd, CLRSINT0, CLRIOERR);
/*
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
* A change in I/O mode is equivalent to a bus reset.
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
*/
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
ahd_reset_channel(ahd, 'A', /*Initiate Reset*/TRUE);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_pause(ahd);
ahd_setup_iocell_workaround(ahd);
ahd_unpause(ahd);
} else if ((status0 & OVERRUN) != 0) {
printf("%s: SCSI offset overrun detected. Resetting bus.\n",
ahd_name(ahd));
ahd_reset_channel(ahd, 'A', /*Initiate Reset*/TRUE);
} else if ((status & SCSIRSTI) != 0) {
printf("%s: Someone reset channel A\n", ahd_name(ahd));
ahd_reset_channel(ahd, 'A', /*Initiate Reset*/FALSE);
} else if ((status & SCSIPERR) != 0) {
ahd_handle_transmission_error(ahd);
} else if (lqostat0 != 0) {
printf("%s: lqostat0 == 0x%x!\n", ahd_name(ahd), lqostat0);
ahd_outb(ahd, CLRLQOINT0, lqostat0);
if ((ahd->bugs & AHD_CLRLQO_AUTOCLR_BUG) != 0) {
ahd_outb(ahd, CLRLQOINT1, 0);
}
} else if ((status & SELTO) != 0) {
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
u_int scbid;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/* Stop the selection */
ahd_outb(ahd, SCSISEQ0, 0);
/* No more pending messages */
ahd_clear_msg_state(ahd);
/* Clear interrupt state */
ahd_outb(ahd, CLRSINT1, CLRSELTIMEO|CLRBUSFREE|CLRSCSIPERR);
/*
* Although the driver does not care about the
* 'Selection in Progress' status bit, the busy
* LED does. SELINGO is only cleared by a sucessfull
* selection, so we must manually clear it to insure
* the LED turns off just incase no future successful
* selections occur (e.g. no devices on the bus).
*/
ahd_outb(ahd, CLRSINT0, CLRSELINGO);
scbid = ahd_inw(ahd, WAITING_TID_HEAD);
scb = ahd_lookup_scb(ahd, scbid);
if (scb == NULL) {
printf("%s: ahd_intr - referenced scb not "
"valid during SELTO scb(0x%x)\n",
ahd_name(ahd), scbid);
ahd_dump_card_state(ahd);
} else {
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
struct ahd_devinfo devinfo;
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_SELTO) != 0) {
ahd_print_path(ahd, scb);
printf("Saw Selection Timeout for SCB 0x%x\n",
scbid);
}
#endif
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
/*
* Force a renegotiation with this target just in
* case the cable was pulled and will later be
* re-attached. The target may forget its negotiation
* settings with us should it attempt to reselect
* during the interruption. The target will not issue
* a unit attention in this case, so we must always
* renegotiate.
*/
ahd_scb_devinfo(ahd, &devinfo, scb);
ahd_force_renegotiation(ahd, &devinfo);
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_set_transaction_status(scb, CAM_SEL_TIMEOUT);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_freeze_devq(ahd, scb);
}
ahd_outb(ahd, CLRINT, CLRSCSIINT);
ahd_iocell_first_selection(ahd);
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
ahd_unpause(ahd);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
} else if ((status0 & (SELDI|SELDO)) != 0) {
ahd_iocell_first_selection(ahd);
ahd_unpause(ahd);
} else if (status3 != 0) {
printf("%s: SCSI Cell parity error SSTAT3 == 0x%x\n",
ahd_name(ahd), status3);
ahd_outb(ahd, CLRSINT3, status3);
} else if ((lqistat1 & (LQIPHASE_LQ|LQIPHASE_NLQ)) != 0) {
ahd_handle_lqiphase_error(ahd, lqistat1);
aic79xx.c: Clear the LQICRC_NLQ status should it pop up after we have already handled the SCSIPERR. During some streaming operations this status can be delayed until the stream ends. Without this change, the driver would complain about a "Missing case in ahd_handle_scsiint". In the LQOBUSFREE handler... Don't return the LQOMGR back to the idle state until after we have cleaned up ENSELO and any status related to this selection. The last thing we need is the LQO manager starting another select-out before we have updated the execution queue. It is not clear whether the LQOMGR would, or would not start a new selection early. Make sure ENSELO is off prior to clearing SELDO by flushing device writes. Move assignment of the next target SCB pointer inside of an if to make the code clearer. The effect is the same. Dump card state in both "Unexpected PKT busfree" paths. In ahd_reset(), set the chip to SCSI mode before reading SXFRCTL1. That register only exists in the SCSI mode. Also set the mode explicitly to the SCSI mode after chip reset due to paranoia. Re-arrange code so that SXFRCTL1 is restored as quickly after the chip reset as possible. S/G structurs must be 8byte aligned. Make this official by saying so in our DMA tag. Disable CIO bus stretch on MDFFSTAT if SHVALID is about to come true. This can cause a CIO bus lockup if a PCI or PCI-X error occurs while the stretch is occurring - the host cannot service the PCI-X error since the CIO bus is locked out and SHVALID will never resolve. The stretch was added in the Rev B to simplify the wait for SHVALID to resolve, but the code to do this in the open source sequencer is so simple it was never removed. Consistently use MAX_OFFSET for the user max syncrate set from non-volatile storage. This ensures that the offset does not conflict with AH?_OFFSET_UNKNOWN. Have ahd_pause_and_flushwork set the mode to ensure that it has access to the registers it checks. Also modify the checking of intstat so that the check against 0xFF can actually succeed if the INT_PEND mask is something other than 0xFF. Although there are no cardbus U320 controllers, this check may be needed to recover from a hot-plug PCI removal that occurs without informing the driver. Fix a typo. sg_prefetch_cnt -> sg_prefetch_align. This fixes an infinite loop at card initialization if the cacheline size is 0. aic79xx.h: Add AHD_EARLY_REQ_BUG bug flag. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. Change AH?_OFFSET_UNKNOWN to 0xFF. This is a value that the curr->offset can never be, unlike '0' which we previously used. This fixes code that only checks for a non-zero offset to determine if a sync negotiation is required since it will fire in the unknown case even if the goal is async. aic79xx.reg: Add comments for LQISTAT bits indicating their names in the 7902 data book. We use slightly different and more descriptive names in the firmware. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. aic79xx.seq: Update comments regarding rundown of the GSFIFO to reflect reality. Fix spelling errors. Since we use an 8byte address and 1 byte length, shorten the size of a block move for the legacy DMA'ed CDB case from 11 to 9 bytes. Remove code that, assuming the abort pending feature worked, would set MK_MESSAGE in the SCB's control byte on completion to catch invalid reselections. Since we don't see interrupts for completed selections, this status update could occur prior to us noticing the SELDO. The "select-out" queue logic will get confused by the MK_MESSAGE bit being set as this is used to catch packatized connections where we select-out with ATN. Since the abort pending feature doesn't work on any released controllers yet, this code was never executed. Add support for the AHD_EARLY_REQ_BUG. Don't ignore persistent REQ assertions just because they were asserted within the bus settle delay window. This allows us to tolerate devices like the GEM318 that violate the SCSI spec. Remove unintentional settnig of SG_CACHE_AVAIL. Writing this bit should have no effect, but who knows... On the Rev A, we must wait for HDMAENACK before loading additional segments to avoid clobbering the address of the first segment in the S/G FIFO. This resolves data-corruption issues with certain IBM (now Hitachi) and Fujitsu U320 drives. Rearrange calc_residual to avoid an extra jmp instruction. On RevA Silicon, if the target returns us to data-out after we have already trained for data-out, it is possible for us to transition the free running clock to data-valid before the required 100ns P1 setup time (8 P1 assertions in fast-160 mode). This will only happen if this L-Q is a continuation of a data transfer for which we have already prefetched data into our FIFO (LQ/Data followed by LQ/Data for the same write transaction). This can cause some target implementations to miss the first few data transfers on the bus. We detect this situation by noticing that this is the first data transfer after an LQ (LQIWORKONLQ true), that the data transfer is a continuation of a transfer already setup in our FIFO (SAVEPTRS interrupt), and that the transaction is a write (DIRECTION set in DFCNTRL). The delay is performed by disabling SCSIEN until we see the first REQ from the target. Only compile in snapshot savepointers handler for RevA silicon where it is enabled. Handle the cfg4icmd packetized interrupt. We just need to load the address and count, start the DMA, and CLRCHN once the transfer is complete. Fix an oversight in the overrun handler for packetized status operations. We need to wait for either CTXTDONE or an overrun when checking for an overrun. The previous code did not wait and thus could decide that no overrun had occurred even though an overrun will occur on the next data-valid req. Add some comment to this section for clarity. Use LAST_SEG_DONE instead of LASTSDONE for testing transfer completion in the packetized status case. LASTSDONE may come up more quickly since it only records completion on the SCSI side, but since LAST_SEG_DONE is used everywhere else (and needs to be), this is less confusing. Add a missing invalidation of the longjmp address in the non-pack handler. This code needs additional review. aic79xx_inline.h: Fix spelling error. aic79xx_osm.c: Set the cdb length for CDBs dma'ed from host memory. Add a comment indicating that, should CAM start supporting cdbs larger than 16bytes, the driver could store the CDB in the status buffer. aic79xx_pci.c: Add a table entry for the 39320A. Added a missing comma to an error string table. Fix spelling errors.
2003-02-27 23:23:16 +00:00
} else if ((lqistat1 & LQICRCI_NLQ) != 0) {
/*
* This status can be delayed during some
* streaming operations. The SCSIPHASE
* handler has already dealt with this case
* so just clear the error.
*/
ahd_outb(ahd, CLRLQIINT1, CLRLQICRCI_NLQ);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
} else if ((status & BUSFREE) != 0) {
u_int lqostat1;
int restart;
int clear_fifo;
int packetized;
u_int mode;
/*
* Clear our selection hardware as soon as possible.
* We may have an entry in the waiting Q for this target,
* that is affected by this busfree and we don't want to
* go about selecting the target while we handle the event.
*/
ahd_outb(ahd, SCSISEQ0, 0);
/*
* Determine what we were up to at the time of
* the busfree.
*/
mode = AHD_MODE_SCSI;
busfreetime = ahd_inb(ahd, SSTAT2) & BUSFREETIME;
lqostat1 = ahd_inb(ahd, LQOSTAT1);
switch (busfreetime) {
case BUSFREE_DFF0:
case BUSFREE_DFF1:
{
u_int scbid;
struct scb *scb;
mode = busfreetime == BUSFREE_DFF0
? AHD_MODE_DFF0 : AHD_MODE_DFF1;
ahd_set_modes(ahd, mode, mode);
scbid = ahd_get_scbptr(ahd);
scb = ahd_lookup_scb(ahd, scbid);
if (scb == NULL) {
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
printf("%s: Invalid SCB %d in DFF%d "
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
"during unexpected busfree\n",
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
ahd_name(ahd), scbid, mode);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
packetized = 0;
} else
packetized = (scb->flags & SCB_PACKETIZED) != 0;
clear_fifo = 1;
break;
}
case BUSFREE_LQO:
clear_fifo = 0;
packetized = 1;
break;
default:
clear_fifo = 0;
packetized = (lqostat1 & LQOBUSFREE) != 0;
if (!packetized
&& ahd_inb(ahd, LASTPHASE) == P_BUSFREE)
packetized = 1;
break;
}
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_MISC) != 0)
printf("Saw Busfree. Busfreetime = 0x%x.\n",
busfreetime);
#endif
/*
* Busfrees that occur in non-packetized phases are
* handled by the nonpkt_busfree handler.
*/
if (packetized && ahd_inb(ahd, LASTPHASE) == P_BUSFREE) {
restart = ahd_handle_pkt_busfree(ahd, busfreetime);
} else {
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
packetized = 0;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
restart = ahd_handle_nonpkt_busfree(ahd);
}
/*
* Clear the busfree interrupt status. The setting of
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
* the interrupt is a pulse, so in a perfect world, we
* would not need to muck with the ENBUSFREE logic. This
* would ensure that if the bus moves on to another
* connection, busfree protection is still in force. If
* BUSFREEREV is broken, however, we must manually clear
* the ENBUSFREE if the busfree occurred during a non-pack
* connection so that we don't get false positives during
* future, packetized, connections.
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
*/
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
ahd_outb(ahd, CLRSINT1, CLRBUSFREE);
if (packetized == 0
&& (ahd->bugs & AHD_BUSFREEREV_BUG) != 0)
ahd_outb(ahd, SIMODE1,
ahd_inb(ahd, SIMODE1) & ~ENBUSFREE);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if (clear_fifo)
ahd_clear_fifo(ahd, mode);
ahd_clear_msg_state(ahd);
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
ahd_outb(ahd, CLRINT, CLRSCSIINT);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
if (restart) {
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_restart(ahd);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
} else {
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_unpause(ahd);
}
} else {
printf("%s: Missing case in ahd_handle_scsiint. status = %x\n",
ahd_name(ahd), status);
ahd_dump_card_state(ahd);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
ahd_clear_intstat(ahd);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_unpause(ahd);
}
}
static void
ahd_handle_transmission_error(struct ahd_softc *ahd)
{
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
struct scb *scb;
u_int scbid;
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
u_int lqistat1;
u_int lqistat2;
u_int msg_out;
u_int curphase;
u_int lastphase;
u_int perrdiag;
u_int cur_col;
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
int silent;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
scb = NULL;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
lqistat1 = ahd_inb(ahd, LQISTAT1) & ~(LQIPHASE_LQ|LQIPHASE_NLQ);
lqistat2 = ahd_inb(ahd, LQISTAT2);
if ((lqistat1 & (LQICRCI_NLQ|LQICRCI_LQ)) == 0
&& (ahd->bugs & AHD_NLQICRC_DELAYED_BUG) != 0) {
u_int lqistate;
ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG);
lqistate = ahd_inb(ahd, LQISTATE);
if ((lqistate >= 0x1E && lqistate <= 0x24)
|| (lqistate == 0x29)) {
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_RECOVERY) != 0) {
printf("%s: NLQCRC found via LQISTATE\n",
ahd_name(ahd));
}
#endif
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
lqistat1 |= LQICRCI_NLQ;
}
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
}
ahd_outb(ahd, CLRLQIINT1, lqistat1);
lastphase = ahd_inb(ahd, LASTPHASE);
curphase = ahd_inb(ahd, SCSISIGI) & PHASE_MASK;
perrdiag = ahd_inb(ahd, PERRDIAG);
msg_out = MSG_INITIATOR_DET_ERR;
ahd_outb(ahd, CLRSINT1, CLRSCSIPERR);
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
/*
* Try to find the SCB associated with this error.
*/
silent = FALSE;
if (lqistat1 == 0
|| (lqistat1 & LQICRCI_NLQ) != 0) {
if ((lqistat1 & (LQICRCI_NLQ|LQIOVERI_NLQ)) != 0)
ahd_set_active_fifo(ahd);
scbid = ahd_get_scbptr(ahd);
scb = ahd_lookup_scb(ahd, scbid);
if (scb != NULL && SCB_IS_SILENT(scb))
silent = TRUE;
}
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
cur_col = 0;
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
if (silent == FALSE) {
printf("%s: Transmission error detected\n", ahd_name(ahd));
ahd_lqistat1_print(lqistat1, &cur_col, 50);
ahd_lastphase_print(lastphase, &cur_col, 50);
ahd_scsisigi_print(curphase, &cur_col, 50);
ahd_perrdiag_print(perrdiag, &cur_col, 50);
printf("\n");
ahd_dump_card_state(ahd);
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if ((lqistat1 & (LQIOVERI_LQ|LQIOVERI_NLQ)) != 0) {
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
if (silent == FALSE) {
printf("%s: Gross protocol error during incoming "
"packet. lqistat1 == 0x%x. Resetting bus.\n",
ahd_name(ahd), lqistat1);
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_reset_channel(ahd, 'A', /*Initiate Reset*/TRUE);
return;
} else if ((lqistat1 & LQICRCI_LQ) != 0) {
/*
* A CRC error has been detected on an incoming LQ.
* The bus is currently hung on the last ACK.
* Hit LQIRETRY to release the last ack, and
* wait for the sequencer to determine that ATNO
* is asserted while in message out to take us
* to our host message loop. No NONPACKREQ or
* LQIPHASE type errors will occur in this
* scenario. After this first LQIRETRY, the LQI
* manager will be in ISELO where it will
* happily sit until another packet phase begins.
* Unexpected bus free detection is enabled
* through any phases that occur after we release
* this last ack until the LQI manager sees a
* packet phase. This implies we may have to
* ignore a perfectly valid "unexected busfree"
* after our "initiator detected error" message is
* sent. A busfree is the expected response after
* we tell the target that it's L_Q was corrupted.
* (SPI4R09 10.7.3.3.3)
*/
ahd_outb(ahd, LQCTL2, LQIRETRY);
printf("LQIRetry for LQICRCI_LQ to release ACK\n");
} else if ((lqistat1 & LQICRCI_NLQ) != 0) {
/*
* We detected a CRC error in a NON-LQ packet.
* The hardware has varying behavior in this situation
* depending on whether this packet was part of a
* stream or not.
*
* PKT by PKT mode:
* The hardware has already acked the complete packet.
* If the target honors our outstanding ATN condition,
* we should be (or soon will be) in MSGOUT phase.
* This will trigger the LQIPHASE_LQ status bit as the
* hardware was expecting another LQ. Unexpected
* busfree detection is enabled. Once LQIPHASE_LQ is
* true (first entry into host message loop is much
* the same), we must clear LQIPHASE_LQ and hit
* LQIRETRY so the hardware is ready to handle
* a future LQ. NONPACKREQ will not be asserted again
* once we hit LQIRETRY until another packet is
* processed. The target may either go busfree
* or start another packet in response to our message.
*
* Read Streaming P0 asserted:
* If we raise ATN and the target completes the entire
* stream (P0 asserted during the last packet), the
* hardware will ack all data and return to the ISTART
* state. When the target reponds to our ATN condition,
* LQIPHASE_LQ will be asserted. We should respond to
* this with an LQIRETRY to prepare for any future
* packets. NONPACKREQ will not be asserted again
* once we hit LQIRETRY until another packet is
* processed. The target may either go busfree or
* start another packet in response to our message.
* Busfree detection is enabled.
*
* Read Streaming P0 not asserted:
* If we raise ATN and the target transitions to
* MSGOUT in or after a packet where P0 is not
* asserted, the hardware will assert LQIPHASE_NLQ.
* We should respond to the LQIPHASE_NLQ with an
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
* LQIRETRY. Should the target stay in a non-pkt
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
* phase after we send our message, the hardware
* will assert LQIPHASE_LQ. Recovery is then just as
* listed above for the read streaming with P0 asserted.
* Busfree detection is enabled.
*/
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
if (silent == FALSE)
printf("LQICRC_NLQ\n");
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if (scb == NULL) {
printf("%s: No SCB valid for LQICRC_NLQ. "
"Resetting bus\n", ahd_name(ahd));
ahd_reset_channel(ahd, 'A', /*Initiate Reset*/TRUE);
return;
}
} else if ((lqistat1 & LQIBADLQI) != 0) {
printf("Need to handle BADLQI!\n");
ahd_reset_channel(ahd, 'A', /*Initiate Reset*/TRUE);
return;
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
} else if ((perrdiag & (PARITYERR|PREVPHASE)) == PARITYERR) {
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if ((curphase & ~P_DATAIN_DT) != 0) {
/* Ack the byte. So we can continue. */
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
if (silent == FALSE)
printf("Acking %s to clear perror\n",
ahd_lookup_phase_entry(curphase)->phasemsg);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_inb(ahd, SCSIDAT);
}
if (curphase == P_MESGIN)
msg_out = MSG_PARITY_ERROR;
}
/*
* We've set the hardware to assert ATN if we
* get a parity error on "in" phases, so all we
* need to do is stuff the message buffer with
* the appropriate message. "In" phases have set
* mesg_out to something other than MSG_NOP.
*/
ahd->send_msg_perror = msg_out;
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
if (scb != NULL && msg_out == MSG_INITIATOR_DET_ERR)
scb->flags |= SCB_TRANSMISSION_ERROR;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_outb(ahd, MSG_OUT, HOST_MSG);
ahd_outb(ahd, CLRINT, CLRSCSIINT);
ahd_unpause(ahd);
}
static void
ahd_handle_lqiphase_error(struct ahd_softc *ahd, u_int lqistat1)
{
/*
* Clear the sources of the interrupts.
*/
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
ahd_outb(ahd, CLRLQIINT1, lqistat1);
/*
* If the "illegal" phase changes were in response
* to our ATN to flag a CRC error, AND we ended up
* on packet boundaries, clear the error, restart the
* LQI manager as appropriate, and go on our merry
* way toward sending the message. Otherwise, reset
* the bus to clear the error.
*/
ahd_set_active_fifo(ahd);
if ((ahd_inb(ahd, SCSISIGO) & ATNO) != 0
&& (ahd_inb(ahd, MDFFSTAT) & DLZERO) != 0) {
if ((lqistat1 & LQIPHASE_LQ) != 0) {
printf("LQIRETRY for LQIPHASE_LQ\n");
ahd_outb(ahd, LQCTL2, LQIRETRY);
} else if ((lqistat1 & LQIPHASE_NLQ) != 0) {
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
printf("LQIRETRY for LQIPHASE_NLQ\n");
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_outb(ahd, LQCTL2, LQIRETRY);
} else
panic("ahd_handle_lqiphase_error: No phase errors\n");
ahd_dump_card_state(ahd);
ahd_outb(ahd, CLRINT, CLRSCSIINT);
ahd_unpause(ahd);
} else {
printf("Reseting Channel for LQI Phase error\n");
ahd_dump_card_state(ahd);
ahd_reset_channel(ahd, 'A', /*Initiate Reset*/TRUE);
}
}
/*
* Packetized unexpected or expected busfree.
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
* Entered in mode based on busfreetime.
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
*/
static int
ahd_handle_pkt_busfree(struct ahd_softc *ahd, u_int busfreetime)
{
u_int lqostat1;
AHD_ASSERT_MODES(ahd, ~(AHD_MODE_UNKNOWN_MSK|AHD_MODE_CFG_MSK),
~(AHD_MODE_UNKNOWN_MSK|AHD_MODE_CFG_MSK));
lqostat1 = ahd_inb(ahd, LQOSTAT1);
if ((lqostat1 & LQOBUSFREE) != 0) {
struct scb *scb;
u_int scbid;
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
u_int saved_scbptr;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
u_int waiting_h;
u_int waiting_t;
u_int next;
if ((busfreetime & BUSFREE_LQO) == 0)
printf("%s: Warning, BUSFREE time is 0x%x. "
"Expected BUSFREE_LQO.\n",
ahd_name(ahd), busfreetime);
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
/*
* The LQO manager detected an unexpected busfree
* either:
*
* 1) During an outgoing LQ.
* 2) After an outgoing LQ but before the first
* REQ of the command packet.
* 3) During an outgoing command packet.
*
* In all cases, CURRSCB is pointing to the
* SCB that encountered the failure. Clean
* up the queue, clear SELDO and LQOBUSFREE,
* and allow the sequencer to restart the select
* out at its lesure.
*/
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
scbid = ahd_inw(ahd, CURRSCB);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
scb = ahd_lookup_scb(ahd, scbid);
if (scb == NULL)
panic("SCB not valid during LQOBUSFREE");
/*
* Clear the status.
*/
ahd_outb(ahd, CLRLQOINT1, CLRLQOBUSFREE);
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
if ((ahd->bugs & AHD_CLRLQO_AUTOCLR_BUG) != 0)
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_outb(ahd, CLRLQOINT1, 0);
ahd_outb(ahd, SCSISEQ0, ahd_inb(ahd, SCSISEQ0) & ~ENSELO);
aic79xx.c: Clear the LQICRC_NLQ status should it pop up after we have already handled the SCSIPERR. During some streaming operations this status can be delayed until the stream ends. Without this change, the driver would complain about a "Missing case in ahd_handle_scsiint". In the LQOBUSFREE handler... Don't return the LQOMGR back to the idle state until after we have cleaned up ENSELO and any status related to this selection. The last thing we need is the LQO manager starting another select-out before we have updated the execution queue. It is not clear whether the LQOMGR would, or would not start a new selection early. Make sure ENSELO is off prior to clearing SELDO by flushing device writes. Move assignment of the next target SCB pointer inside of an if to make the code clearer. The effect is the same. Dump card state in both "Unexpected PKT busfree" paths. In ahd_reset(), set the chip to SCSI mode before reading SXFRCTL1. That register only exists in the SCSI mode. Also set the mode explicitly to the SCSI mode after chip reset due to paranoia. Re-arrange code so that SXFRCTL1 is restored as quickly after the chip reset as possible. S/G structurs must be 8byte aligned. Make this official by saying so in our DMA tag. Disable CIO bus stretch on MDFFSTAT if SHVALID is about to come true. This can cause a CIO bus lockup if a PCI or PCI-X error occurs while the stretch is occurring - the host cannot service the PCI-X error since the CIO bus is locked out and SHVALID will never resolve. The stretch was added in the Rev B to simplify the wait for SHVALID to resolve, but the code to do this in the open source sequencer is so simple it was never removed. Consistently use MAX_OFFSET for the user max syncrate set from non-volatile storage. This ensures that the offset does not conflict with AH?_OFFSET_UNKNOWN. Have ahd_pause_and_flushwork set the mode to ensure that it has access to the registers it checks. Also modify the checking of intstat so that the check against 0xFF can actually succeed if the INT_PEND mask is something other than 0xFF. Although there are no cardbus U320 controllers, this check may be needed to recover from a hot-plug PCI removal that occurs without informing the driver. Fix a typo. sg_prefetch_cnt -> sg_prefetch_align. This fixes an infinite loop at card initialization if the cacheline size is 0. aic79xx.h: Add AHD_EARLY_REQ_BUG bug flag. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. Change AH?_OFFSET_UNKNOWN to 0xFF. This is a value that the curr->offset can never be, unlike '0' which we previously used. This fixes code that only checks for a non-zero offset to determine if a sync negotiation is required since it will fire in the unknown case even if the goal is async. aic79xx.reg: Add comments for LQISTAT bits indicating their names in the 7902 data book. We use slightly different and more descriptive names in the firmware. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. aic79xx.seq: Update comments regarding rundown of the GSFIFO to reflect reality. Fix spelling errors. Since we use an 8byte address and 1 byte length, shorten the size of a block move for the legacy DMA'ed CDB case from 11 to 9 bytes. Remove code that, assuming the abort pending feature worked, would set MK_MESSAGE in the SCB's control byte on completion to catch invalid reselections. Since we don't see interrupts for completed selections, this status update could occur prior to us noticing the SELDO. The "select-out" queue logic will get confused by the MK_MESSAGE bit being set as this is used to catch packatized connections where we select-out with ATN. Since the abort pending feature doesn't work on any released controllers yet, this code was never executed. Add support for the AHD_EARLY_REQ_BUG. Don't ignore persistent REQ assertions just because they were asserted within the bus settle delay window. This allows us to tolerate devices like the GEM318 that violate the SCSI spec. Remove unintentional settnig of SG_CACHE_AVAIL. Writing this bit should have no effect, but who knows... On the Rev A, we must wait for HDMAENACK before loading additional segments to avoid clobbering the address of the first segment in the S/G FIFO. This resolves data-corruption issues with certain IBM (now Hitachi) and Fujitsu U320 drives. Rearrange calc_residual to avoid an extra jmp instruction. On RevA Silicon, if the target returns us to data-out after we have already trained for data-out, it is possible for us to transition the free running clock to data-valid before the required 100ns P1 setup time (8 P1 assertions in fast-160 mode). This will only happen if this L-Q is a continuation of a data transfer for which we have already prefetched data into our FIFO (LQ/Data followed by LQ/Data for the same write transaction). This can cause some target implementations to miss the first few data transfers on the bus. We detect this situation by noticing that this is the first data transfer after an LQ (LQIWORKONLQ true), that the data transfer is a continuation of a transfer already setup in our FIFO (SAVEPTRS interrupt), and that the transaction is a write (DIRECTION set in DFCNTRL). The delay is performed by disabling SCSIEN until we see the first REQ from the target. Only compile in snapshot savepointers handler for RevA silicon where it is enabled. Handle the cfg4icmd packetized interrupt. We just need to load the address and count, start the DMA, and CLRCHN once the transfer is complete. Fix an oversight in the overrun handler for packetized status operations. We need to wait for either CTXTDONE or an overrun when checking for an overrun. The previous code did not wait and thus could decide that no overrun had occurred even though an overrun will occur on the next data-valid req. Add some comment to this section for clarity. Use LAST_SEG_DONE instead of LASTSDONE for testing transfer completion in the packetized status case. LASTSDONE may come up more quickly since it only records completion on the SCSI side, but since LAST_SEG_DONE is used everywhere else (and needs to be), this is less confusing. Add a missing invalidation of the longjmp address in the non-pack handler. This code needs additional review. aic79xx_inline.h: Fix spelling error. aic79xx_osm.c: Set the cdb length for CDBs dma'ed from host memory. Add a comment indicating that, should CAM start supporting cdbs larger than 16bytes, the driver could store the CDB in the status buffer. aic79xx_pci.c: Add a table entry for the 39320A. Added a missing comma to an error string table. Fix spelling errors.
2003-02-27 23:23:16 +00:00
ahd_flush_device_writes(ahd);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_outb(ahd, CLRSINT0, CLRSELDO);
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
aic79xx.c: Clear the LQICRC_NLQ status should it pop up after we have already handled the SCSIPERR. During some streaming operations this status can be delayed until the stream ends. Without this change, the driver would complain about a "Missing case in ahd_handle_scsiint". In the LQOBUSFREE handler... Don't return the LQOMGR back to the idle state until after we have cleaned up ENSELO and any status related to this selection. The last thing we need is the LQO manager starting another select-out before we have updated the execution queue. It is not clear whether the LQOMGR would, or would not start a new selection early. Make sure ENSELO is off prior to clearing SELDO by flushing device writes. Move assignment of the next target SCB pointer inside of an if to make the code clearer. The effect is the same. Dump card state in both "Unexpected PKT busfree" paths. In ahd_reset(), set the chip to SCSI mode before reading SXFRCTL1. That register only exists in the SCSI mode. Also set the mode explicitly to the SCSI mode after chip reset due to paranoia. Re-arrange code so that SXFRCTL1 is restored as quickly after the chip reset as possible. S/G structurs must be 8byte aligned. Make this official by saying so in our DMA tag. Disable CIO bus stretch on MDFFSTAT if SHVALID is about to come true. This can cause a CIO bus lockup if a PCI or PCI-X error occurs while the stretch is occurring - the host cannot service the PCI-X error since the CIO bus is locked out and SHVALID will never resolve. The stretch was added in the Rev B to simplify the wait for SHVALID to resolve, but the code to do this in the open source sequencer is so simple it was never removed. Consistently use MAX_OFFSET for the user max syncrate set from non-volatile storage. This ensures that the offset does not conflict with AH?_OFFSET_UNKNOWN. Have ahd_pause_and_flushwork set the mode to ensure that it has access to the registers it checks. Also modify the checking of intstat so that the check against 0xFF can actually succeed if the INT_PEND mask is something other than 0xFF. Although there are no cardbus U320 controllers, this check may be needed to recover from a hot-plug PCI removal that occurs without informing the driver. Fix a typo. sg_prefetch_cnt -> sg_prefetch_align. This fixes an infinite loop at card initialization if the cacheline size is 0. aic79xx.h: Add AHD_EARLY_REQ_BUG bug flag. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. Change AH?_OFFSET_UNKNOWN to 0xFF. This is a value that the curr->offset can never be, unlike '0' which we previously used. This fixes code that only checks for a non-zero offset to determine if a sync negotiation is required since it will fire in the unknown case even if the goal is async. aic79xx.reg: Add comments for LQISTAT bits indicating their names in the 7902 data book. We use slightly different and more descriptive names in the firmware. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. aic79xx.seq: Update comments regarding rundown of the GSFIFO to reflect reality. Fix spelling errors. Since we use an 8byte address and 1 byte length, shorten the size of a block move for the legacy DMA'ed CDB case from 11 to 9 bytes. Remove code that, assuming the abort pending feature worked, would set MK_MESSAGE in the SCB's control byte on completion to catch invalid reselections. Since we don't see interrupts for completed selections, this status update could occur prior to us noticing the SELDO. The "select-out" queue logic will get confused by the MK_MESSAGE bit being set as this is used to catch packatized connections where we select-out with ATN. Since the abort pending feature doesn't work on any released controllers yet, this code was never executed. Add support for the AHD_EARLY_REQ_BUG. Don't ignore persistent REQ assertions just because they were asserted within the bus settle delay window. This allows us to tolerate devices like the GEM318 that violate the SCSI spec. Remove unintentional settnig of SG_CACHE_AVAIL. Writing this bit should have no effect, but who knows... On the Rev A, we must wait for HDMAENACK before loading additional segments to avoid clobbering the address of the first segment in the S/G FIFO. This resolves data-corruption issues with certain IBM (now Hitachi) and Fujitsu U320 drives. Rearrange calc_residual to avoid an extra jmp instruction. On RevA Silicon, if the target returns us to data-out after we have already trained for data-out, it is possible for us to transition the free running clock to data-valid before the required 100ns P1 setup time (8 P1 assertions in fast-160 mode). This will only happen if this L-Q is a continuation of a data transfer for which we have already prefetched data into our FIFO (LQ/Data followed by LQ/Data for the same write transaction). This can cause some target implementations to miss the first few data transfers on the bus. We detect this situation by noticing that this is the first data transfer after an LQ (LQIWORKONLQ true), that the data transfer is a continuation of a transfer already setup in our FIFO (SAVEPTRS interrupt), and that the transaction is a write (DIRECTION set in DFCNTRL). The delay is performed by disabling SCSIEN until we see the first REQ from the target. Only compile in snapshot savepointers handler for RevA silicon where it is enabled. Handle the cfg4icmd packetized interrupt. We just need to load the address and count, start the DMA, and CLRCHN once the transfer is complete. Fix an oversight in the overrun handler for packetized status operations. We need to wait for either CTXTDONE or an overrun when checking for an overrun. The previous code did not wait and thus could decide that no overrun had occurred even though an overrun will occur on the next data-valid req. Add some comment to this section for clarity. Use LAST_SEG_DONE instead of LASTSDONE for testing transfer completion in the packetized status case. LASTSDONE may come up more quickly since it only records completion on the SCSI side, but since LAST_SEG_DONE is used everywhere else (and needs to be), this is less confusing. Add a missing invalidation of the longjmp address in the non-pack handler. This code needs additional review. aic79xx_inline.h: Fix spelling error. aic79xx_osm.c: Set the cdb length for CDBs dma'ed from host memory. Add a comment indicating that, should CAM start supporting cdbs larger than 16bytes, the driver could store the CDB in the status buffer. aic79xx_pci.c: Add a table entry for the 39320A. Added a missing comma to an error string table. Fix spelling errors.
2003-02-27 23:23:16 +00:00
/*
* Return the LQO manager to its idle loop. It will
* not do this automatically if the busfree occurs
* after the first REQ of either the LQ or command
* packet or between the LQ and command packet.
*/
ahd_outb(ahd, LQCTL2, ahd_inb(ahd, LQCTL2) | LQOTOIDLE);
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
/*
* Update the waiting for selection queue so
* we restart on the correct SCB.
*/
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
waiting_h = ahd_inw(ahd, WAITING_TID_HEAD);
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
saved_scbptr = ahd_get_scbptr(ahd);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if (waiting_h != scbid) {
ahd_outw(ahd, WAITING_TID_HEAD, scbid);
waiting_t = ahd_inw(ahd, WAITING_TID_TAIL);
if (waiting_t == waiting_h) {
ahd_outw(ahd, WAITING_TID_TAIL, scbid);
aic79xx.c: Clear the LQICRC_NLQ status should it pop up after we have already handled the SCSIPERR. During some streaming operations this status can be delayed until the stream ends. Without this change, the driver would complain about a "Missing case in ahd_handle_scsiint". In the LQOBUSFREE handler... Don't return the LQOMGR back to the idle state until after we have cleaned up ENSELO and any status related to this selection. The last thing we need is the LQO manager starting another select-out before we have updated the execution queue. It is not clear whether the LQOMGR would, or would not start a new selection early. Make sure ENSELO is off prior to clearing SELDO by flushing device writes. Move assignment of the next target SCB pointer inside of an if to make the code clearer. The effect is the same. Dump card state in both "Unexpected PKT busfree" paths. In ahd_reset(), set the chip to SCSI mode before reading SXFRCTL1. That register only exists in the SCSI mode. Also set the mode explicitly to the SCSI mode after chip reset due to paranoia. Re-arrange code so that SXFRCTL1 is restored as quickly after the chip reset as possible. S/G structurs must be 8byte aligned. Make this official by saying so in our DMA tag. Disable CIO bus stretch on MDFFSTAT if SHVALID is about to come true. This can cause a CIO bus lockup if a PCI or PCI-X error occurs while the stretch is occurring - the host cannot service the PCI-X error since the CIO bus is locked out and SHVALID will never resolve. The stretch was added in the Rev B to simplify the wait for SHVALID to resolve, but the code to do this in the open source sequencer is so simple it was never removed. Consistently use MAX_OFFSET for the user max syncrate set from non-volatile storage. This ensures that the offset does not conflict with AH?_OFFSET_UNKNOWN. Have ahd_pause_and_flushwork set the mode to ensure that it has access to the registers it checks. Also modify the checking of intstat so that the check against 0xFF can actually succeed if the INT_PEND mask is something other than 0xFF. Although there are no cardbus U320 controllers, this check may be needed to recover from a hot-plug PCI removal that occurs without informing the driver. Fix a typo. sg_prefetch_cnt -> sg_prefetch_align. This fixes an infinite loop at card initialization if the cacheline size is 0. aic79xx.h: Add AHD_EARLY_REQ_BUG bug flag. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. Change AH?_OFFSET_UNKNOWN to 0xFF. This is a value that the curr->offset can never be, unlike '0' which we previously used. This fixes code that only checks for a non-zero offset to determine if a sync negotiation is required since it will fire in the unknown case even if the goal is async. aic79xx.reg: Add comments for LQISTAT bits indicating their names in the 7902 data book. We use slightly different and more descriptive names in the firmware. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. aic79xx.seq: Update comments regarding rundown of the GSFIFO to reflect reality. Fix spelling errors. Since we use an 8byte address and 1 byte length, shorten the size of a block move for the legacy DMA'ed CDB case from 11 to 9 bytes. Remove code that, assuming the abort pending feature worked, would set MK_MESSAGE in the SCB's control byte on completion to catch invalid reselections. Since we don't see interrupts for completed selections, this status update could occur prior to us noticing the SELDO. The "select-out" queue logic will get confused by the MK_MESSAGE bit being set as this is used to catch packatized connections where we select-out with ATN. Since the abort pending feature doesn't work on any released controllers yet, this code was never executed. Add support for the AHD_EARLY_REQ_BUG. Don't ignore persistent REQ assertions just because they were asserted within the bus settle delay window. This allows us to tolerate devices like the GEM318 that violate the SCSI spec. Remove unintentional settnig of SG_CACHE_AVAIL. Writing this bit should have no effect, but who knows... On the Rev A, we must wait for HDMAENACK before loading additional segments to avoid clobbering the address of the first segment in the S/G FIFO. This resolves data-corruption issues with certain IBM (now Hitachi) and Fujitsu U320 drives. Rearrange calc_residual to avoid an extra jmp instruction. On RevA Silicon, if the target returns us to data-out after we have already trained for data-out, it is possible for us to transition the free running clock to data-valid before the required 100ns P1 setup time (8 P1 assertions in fast-160 mode). This will only happen if this L-Q is a continuation of a data transfer for which we have already prefetched data into our FIFO (LQ/Data followed by LQ/Data for the same write transaction). This can cause some target implementations to miss the first few data transfers on the bus. We detect this situation by noticing that this is the first data transfer after an LQ (LQIWORKONLQ true), that the data transfer is a continuation of a transfer already setup in our FIFO (SAVEPTRS interrupt), and that the transaction is a write (DIRECTION set in DFCNTRL). The delay is performed by disabling SCSIEN until we see the first REQ from the target. Only compile in snapshot savepointers handler for RevA silicon where it is enabled. Handle the cfg4icmd packetized interrupt. We just need to load the address and count, start the DMA, and CLRCHN once the transfer is complete. Fix an oversight in the overrun handler for packetized status operations. We need to wait for either CTXTDONE or an overrun when checking for an overrun. The previous code did not wait and thus could decide that no overrun had occurred even though an overrun will occur on the next data-valid req. Add some comment to this section for clarity. Use LAST_SEG_DONE instead of LASTSDONE for testing transfer completion in the packetized status case. LASTSDONE may come up more quickly since it only records completion on the SCSI side, but since LAST_SEG_DONE is used everywhere else (and needs to be), this is less confusing. Add a missing invalidation of the longjmp address in the non-pack handler. This code needs additional review. aic79xx_inline.h: Fix spelling error. aic79xx_osm.c: Set the cdb length for CDBs dma'ed from host memory. Add a comment indicating that, should CAM start supporting cdbs larger than 16bytes, the driver could store the CDB in the status buffer. aic79xx_pci.c: Add a table entry for the 39320A. Added a missing comma to an error string table. Fix spelling errors.
2003-02-27 23:23:16 +00:00
next = SCB_LIST_NULL;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
} else {
ahd_set_scbptr(ahd, waiting_h);
aic79xx.c: Include read streaming in the PPR flags we display in diagnostics. In ahd_reset(), set the known mode after our initial pause prior to setting the mode. We can't just set the mode directly because the current mode, after the pause, is most likely unknown and setting the mode when the saved mode is unknown will trigger an assertion in the mode debug code. Complete an audit for SCB RAM reads. These reads must be performed via the special ahd_in?_scbram() methods so we can perform a Rev A. PCI-X workaround. Remove a superfluous mode save operation that was performed just prior to a call to ahd_clear_critical_section(). The saved mode was never restored and wouldn't have been valid anyway since the mode could change while single stepping out of a critical section. aic79xx.h: Add new BUG definition AHD_PCIX_SCBRAM_RD_BUG. aic79xx_inline.h: Update ahd_inb_scbram routine to check for AHD_PCIX_SCBRAM_RD_BUG and only apply the workaround if this bug is active. The old code applied the workaround in all cases. aic79xx_pci.c: Set AHD_PCIX_SCBRAM_RD_BUG for the A4. Remove an attempted saved_modes call in ahd_pci_test_register_access(). Saving the modes can only occur when we are paused, but the call was happening before the chip was known to be paused. Restoring the modes doesn't make sense either since the code makes no assumptions about the state of the sequencer until the first time the mode is set by the driver. This happens after the registers are successfully mapped.
2003-03-06 23:58:34 +00:00
next = ahd_inw_scbram(ahd, SCB_NEXT2);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
ahd_set_scbptr(ahd, scbid);
ahd_outw(ahd, SCB_NEXT2, next);
}
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
ahd_set_scbptr(ahd, saved_scbptr);
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
if (scb->crc_retry_count < AHD_MAX_LQ_CRC_ERRORS) {
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
if (SCB_IS_SILENT(scb) == FALSE) {
ahd_print_path(ahd, scb);
printf("Probable outgoing LQ CRC error. "
"Retrying command\n");
}
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
scb->crc_retry_count++;
} else {
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_set_transaction_status(scb, CAM_UNCOR_PARITY);
aic_freeze_scb(scb);
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
ahd_freeze_devq(ahd, scb);
}
/* Return unpausing the sequencer. */
return (0);
} else if ((ahd_inb(ahd, PERRDIAG) & PARITYERR) != 0) {
/*
* Ignore what are really parity errors that
* occur on the last REQ of a free running
* clock prior to going busfree. Some drives
* do not properly active negate just before
* going busfree resulting in a parity glitch.
*/
ahd_outb(ahd, CLRSINT1, CLRSCSIPERR|CLRBUSFREE);
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_MASKED_ERRORS) != 0)
printf("%s: Parity on last REQ detected "
"during busfree phase.\n",
ahd_name(ahd));
#endif
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/* Return unpausing the sequencer. */
return (0);
}
if (ahd->src_mode != AHD_MODE_SCSI) {
u_int scbid;
struct scb *scb;
scbid = ahd_get_scbptr(ahd);
scb = ahd_lookup_scb(ahd, scbid);
ahd_print_path(ahd, scb);
printf("Unexpected PKT busfree condition\n");
aic79xx.c: Clear the LQICRC_NLQ status should it pop up after we have already handled the SCSIPERR. During some streaming operations this status can be delayed until the stream ends. Without this change, the driver would complain about a "Missing case in ahd_handle_scsiint". In the LQOBUSFREE handler... Don't return the LQOMGR back to the idle state until after we have cleaned up ENSELO and any status related to this selection. The last thing we need is the LQO manager starting another select-out before we have updated the execution queue. It is not clear whether the LQOMGR would, or would not start a new selection early. Make sure ENSELO is off prior to clearing SELDO by flushing device writes. Move assignment of the next target SCB pointer inside of an if to make the code clearer. The effect is the same. Dump card state in both "Unexpected PKT busfree" paths. In ahd_reset(), set the chip to SCSI mode before reading SXFRCTL1. That register only exists in the SCSI mode. Also set the mode explicitly to the SCSI mode after chip reset due to paranoia. Re-arrange code so that SXFRCTL1 is restored as quickly after the chip reset as possible. S/G structurs must be 8byte aligned. Make this official by saying so in our DMA tag. Disable CIO bus stretch on MDFFSTAT if SHVALID is about to come true. This can cause a CIO bus lockup if a PCI or PCI-X error occurs while the stretch is occurring - the host cannot service the PCI-X error since the CIO bus is locked out and SHVALID will never resolve. The stretch was added in the Rev B to simplify the wait for SHVALID to resolve, but the code to do this in the open source sequencer is so simple it was never removed. Consistently use MAX_OFFSET for the user max syncrate set from non-volatile storage. This ensures that the offset does not conflict with AH?_OFFSET_UNKNOWN. Have ahd_pause_and_flushwork set the mode to ensure that it has access to the registers it checks. Also modify the checking of intstat so that the check against 0xFF can actually succeed if the INT_PEND mask is something other than 0xFF. Although there are no cardbus U320 controllers, this check may be needed to recover from a hot-plug PCI removal that occurs without informing the driver. Fix a typo. sg_prefetch_cnt -> sg_prefetch_align. This fixes an infinite loop at card initialization if the cacheline size is 0. aic79xx.h: Add AHD_EARLY_REQ_BUG bug flag. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. Change AH?_OFFSET_UNKNOWN to 0xFF. This is a value that the curr->offset can never be, unlike '0' which we previously used. This fixes code that only checks for a non-zero offset to determine if a sync negotiation is required since it will fire in the unknown case even if the goal is async. aic79xx.reg: Add comments for LQISTAT bits indicating their names in the 7902 data book. We use slightly different and more descriptive names in the firmware. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. aic79xx.seq: Update comments regarding rundown of the GSFIFO to reflect reality. Fix spelling errors. Since we use an 8byte address and 1 byte length, shorten the size of a block move for the legacy DMA'ed CDB case from 11 to 9 bytes. Remove code that, assuming the abort pending feature worked, would set MK_MESSAGE in the SCB's control byte on completion to catch invalid reselections. Since we don't see interrupts for completed selections, this status update could occur prior to us noticing the SELDO. The "select-out" queue logic will get confused by the MK_MESSAGE bit being set as this is used to catch packatized connections where we select-out with ATN. Since the abort pending feature doesn't work on any released controllers yet, this code was never executed. Add support for the AHD_EARLY_REQ_BUG. Don't ignore persistent REQ assertions just because they were asserted within the bus settle delay window. This allows us to tolerate devices like the GEM318 that violate the SCSI spec. Remove unintentional settnig of SG_CACHE_AVAIL. Writing this bit should have no effect, but who knows... On the Rev A, we must wait for HDMAENACK before loading additional segments to avoid clobbering the address of the first segment in the S/G FIFO. This resolves data-corruption issues with certain IBM (now Hitachi) and Fujitsu U320 drives. Rearrange calc_residual to avoid an extra jmp instruction. On RevA Silicon, if the target returns us to data-out after we have already trained for data-out, it is possible for us to transition the free running clock to data-valid before the required 100ns P1 setup time (8 P1 assertions in fast-160 mode). This will only happen if this L-Q is a continuation of a data transfer for which we have already prefetched data into our FIFO (LQ/Data followed by LQ/Data for the same write transaction). This can cause some target implementations to miss the first few data transfers on the bus. We detect this situation by noticing that this is the first data transfer after an LQ (LQIWORKONLQ true), that the data transfer is a continuation of a transfer already setup in our FIFO (SAVEPTRS interrupt), and that the transaction is a write (DIRECTION set in DFCNTRL). The delay is performed by disabling SCSIEN until we see the first REQ from the target. Only compile in snapshot savepointers handler for RevA silicon where it is enabled. Handle the cfg4icmd packetized interrupt. We just need to load the address and count, start the DMA, and CLRCHN once the transfer is complete. Fix an oversight in the overrun handler for packetized status operations. We need to wait for either CTXTDONE or an overrun when checking for an overrun. The previous code did not wait and thus could decide that no overrun had occurred even though an overrun will occur on the next data-valid req. Add some comment to this section for clarity. Use LAST_SEG_DONE instead of LASTSDONE for testing transfer completion in the packetized status case. LASTSDONE may come up more quickly since it only records completion on the SCSI side, but since LAST_SEG_DONE is used everywhere else (and needs to be), this is less confusing. Add a missing invalidation of the longjmp address in the non-pack handler. This code needs additional review. aic79xx_inline.h: Fix spelling error. aic79xx_osm.c: Set the cdb length for CDBs dma'ed from host memory. Add a comment indicating that, should CAM start supporting cdbs larger than 16bytes, the driver could store the CDB in the status buffer. aic79xx_pci.c: Add a table entry for the 39320A. Added a missing comma to an error string table. Fix spelling errors.
2003-02-27 23:23:16 +00:00
ahd_dump_card_state(ahd);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_abort_scbs(ahd, SCB_GET_TARGET(ahd, scb), 'A',
SCB_GET_LUN(scb), SCB_GET_TAG(scb),
ROLE_INITIATOR, CAM_UNEXP_BUSFREE);
/* Return restarting the sequencer. */
return (1);
}
printf("%s: Unexpected PKT busfree condition\n", ahd_name(ahd));
ahd_dump_card_state(ahd);
/* Restart the sequencer. */
return (1);
}
/*
* Non-packetized unexpected or expected busfree.
*/
static int
ahd_handle_nonpkt_busfree(struct ahd_softc *ahd)
{
struct ahd_devinfo devinfo;
struct scb *scb;
u_int lastphase;
u_int saved_scsiid;
u_int saved_lun;
u_int target;
u_int initiator_role_id;
u_int scbid;
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
u_int ppr_busfree;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
int printerror;
/*
* Look at what phase we were last in. If its message out,
* chances are pretty good that the busfree was in response
* to one of our abort requests.
*/
lastphase = ahd_inb(ahd, LASTPHASE);
saved_scsiid = ahd_inb(ahd, SAVED_SCSIID);
saved_lun = ahd_inb(ahd, SAVED_LUN);
target = SCSIID_TARGET(ahd, saved_scsiid);
initiator_role_id = SCSIID_OUR_ID(saved_scsiid);
ahd_compile_devinfo(&devinfo, initiator_role_id,
target, saved_lun, 'A', ROLE_INITIATOR);
printerror = 1;
scbid = ahd_get_scbptr(ahd);
scb = ahd_lookup_scb(ahd, scbid);
if (scb != NULL
&& (ahd_inb(ahd, SEQ_FLAGS) & NOT_IDENTIFIED) != 0)
scb = NULL;
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
ppr_busfree = (ahd->msg_flags & MSG_FLAG_EXPECT_PPR_BUSFREE) != 0;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if (lastphase == P_MESGOUT) {
u_int tag;
tag = SCB_LIST_NULL;
if (ahd_sent_msg(ahd, AHDMSG_1B, MSG_ABORT_TAG, TRUE)
|| ahd_sent_msg(ahd, AHDMSG_1B, MSG_ABORT, TRUE)) {
int found;
int sent_msg;
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
if (scb == NULL) {
ahd_print_devinfo(ahd, &devinfo);
printf("Abort for unidentified "
"connection completed.\n");
/* restart the sequencer. */
return (1);
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
sent_msg = ahd->msgout_buf[ahd->msgout_index - 1];
ahd_print_path(ahd, scb);
printf("SCB %d - Abort%s Completed.\n",
SCB_GET_TAG(scb),
sent_msg == MSG_ABORT_TAG ? "" : " Tag");
if (sent_msg == MSG_ABORT_TAG)
tag = SCB_GET_TAG(scb);
if ((scb->flags & SCB_CMDPHASE_ABORT) != 0) {
/*
* This abort is in response to an
* unexpected switch to command phase
* for a packetized connection. Since
* the identify message was never sent,
* "saved lun" is 0. We really want to
* abort only the SCB that encountered
* this error, which could have a different
* lun. The SCB will be retried so the OS
* will see the UA after renegotiating to
* packetized.
*/
tag = SCB_GET_TAG(scb);
saved_lun = scb->hscb->lun;
}
found = ahd_abort_scbs(ahd, target, 'A', saved_lun,
tag, ROLE_INITIATOR,
CAM_REQ_ABORTED);
printf("found == 0x%x\n", found);
printerror = 0;
} else if (ahd_sent_msg(ahd, AHDMSG_1B,
MSG_BUS_DEV_RESET, TRUE)) {
#ifdef __FreeBSD__
/*
* Don't mark the user's request for this BDR
* as completing with CAM_BDR_SENT. CAM3
* specifies CAM_REQ_CMP.
*/
if (scb != NULL
&& scb->io_ctx->ccb_h.func_code== XPT_RESET_DEV
&& ahd_match_scb(ahd, scb, target, 'A',
CAM_LUN_WILDCARD, SCB_LIST_NULL,
ROLE_INITIATOR))
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_set_transaction_status(scb, CAM_REQ_CMP);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
#endif
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
ahd_handle_devreset(ahd, &devinfo, CAM_LUN_WILDCARD,
CAM_BDR_SENT, "Bus Device Reset",
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*verbose_level*/0);
printerror = 0;
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
} else if (ahd_sent_msg(ahd, AHDMSG_EXT, MSG_EXT_PPR, FALSE)
&& ppr_busfree == 0) {
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
struct ahd_initiator_tinfo *tinfo;
struct ahd_tmode_tstate *tstate;
/*
* PPR Rejected. Try non-ppr negotiation
* and retry command.
*/
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_MESSAGES) != 0)
printf("PPR negotiation rejected busfree.\n");
#endif
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
tinfo = ahd_fetch_transinfo(ahd, devinfo.channel,
devinfo.our_scsiid,
devinfo.target, &tstate);
tinfo->curr.transport_version = 2;
tinfo->goal.transport_version = 2;
tinfo->goal.ppr_options = 0;
ahd_qinfifo_requeue_tail(ahd, scb);
printerror = 0;
Work around SCSI spec violation by the Quantum Atlas 10K. This drive delays going async after receiving a WDTR message. We now send an SDTR message after a WDTR even if our goal is to go async. This should work even for confused devices. If we get an unexpected busfree when attempting a WDTR or SDTR, only set the goal negotiation parameters we were trying to negotiate to off. This means that should a WDTR message fail, we will still try an SDTR if our goal is non-async. Fix a few more places where we were looking at goal.period instead of goal.offset for determining if we should be negotiating sync. This should not have any impact on our behavior, but the offset is more definitive and should be used.
2003-06-06 23:51:13 +00:00
} else if (ahd_sent_msg(ahd, AHDMSG_EXT, MSG_EXT_WDTR, FALSE)
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
&& ppr_busfree == 0) {
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*
Work around SCSI spec violation by the Quantum Atlas 10K. This drive delays going async after receiving a WDTR message. We now send an SDTR message after a WDTR even if our goal is to go async. This should work even for confused devices. If we get an unexpected busfree when attempting a WDTR or SDTR, only set the goal negotiation parameters we were trying to negotiate to off. This means that should a WDTR message fail, we will still try an SDTR if our goal is non-async. Fix a few more places where we were looking at goal.period instead of goal.offset for determining if we should be negotiating sync. This should not have any impact on our behavior, but the offset is more definitive and should be used.
2003-06-06 23:51:13 +00:00
* Negotiation Rejected. Go-narrow and
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
* retry command.
*/
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_MESSAGES) != 0)
Work around SCSI spec violation by the Quantum Atlas 10K. This drive delays going async after receiving a WDTR message. We now send an SDTR message after a WDTR even if our goal is to go async. This should work even for confused devices. If we get an unexpected busfree when attempting a WDTR or SDTR, only set the goal negotiation parameters we were trying to negotiate to off. This means that should a WDTR message fail, we will still try an SDTR if our goal is non-async. Fix a few more places where we were looking at goal.period instead of goal.offset for determining if we should be negotiating sync. This should not have any impact on our behavior, but the offset is more definitive and should be used.
2003-06-06 23:51:13 +00:00
printf("WDTR negotiation rejected busfree.\n");
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
#endif
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_set_width(ahd, &devinfo,
MSG_EXT_WDTR_BUS_8_BIT,
AHD_TRANS_CUR|AHD_TRANS_GOAL,
/*paused*/TRUE);
Work around SCSI spec violation by the Quantum Atlas 10K. This drive delays going async after receiving a WDTR message. We now send an SDTR message after a WDTR even if our goal is to go async. This should work even for confused devices. If we get an unexpected busfree when attempting a WDTR or SDTR, only set the goal negotiation parameters we were trying to negotiate to off. This means that should a WDTR message fail, we will still try an SDTR if our goal is non-async. Fix a few more places where we were looking at goal.period instead of goal.offset for determining if we should be negotiating sync. This should not have any impact on our behavior, but the offset is more definitive and should be used.
2003-06-06 23:51:13 +00:00
ahd_qinfifo_requeue_tail(ahd, scb);
printerror = 0;
} else if (ahd_sent_msg(ahd, AHDMSG_EXT, MSG_EXT_SDTR, FALSE)
&& ppr_busfree == 0) {
/*
* Negotiation Rejected. Go-async and
* retry command.
*/
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_MESSAGES) != 0)
printf("SDTR negotiation rejected busfree.\n");
#endif
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_set_syncrate(ahd, &devinfo,
/*period*/0, /*offset*/0,
/*ppr_options*/0,
AHD_TRANS_CUR|AHD_TRANS_GOAL,
/*paused*/TRUE);
ahd_qinfifo_requeue_tail(ahd, scb);
printerror = 0;
} else if ((ahd->msg_flags & MSG_FLAG_EXPECT_IDE_BUSFREE) != 0
&& ahd_sent_msg(ahd, AHDMSG_1B,
MSG_INITIATOR_DET_ERR, TRUE)) {
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_MESSAGES) != 0)
printf("Expected IDE Busfree\n");
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
#endif
printerror = 0;
} else if ((ahd->msg_flags & MSG_FLAG_EXPECT_QASREJ_BUSFREE)
&& ahd_sent_msg(ahd, AHDMSG_1B,
MSG_MESSAGE_REJECT, TRUE)) {
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_MESSAGES) != 0)
printf("Expected QAS Reject Busfree\n");
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
#endif
printerror = 0;
}
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
/*
* The busfree required flag is honored at the end of
* the message phases. We check it last in case we
* had to send some other message that caused a busfree.
*/
if (printerror != 0
&& (lastphase == P_MESGIN || lastphase == P_MESGOUT)
&& ((ahd->msg_flags & MSG_FLAG_EXPECT_PPR_BUSFREE) != 0)) {
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
ahd_freeze_devq(ahd, scb);
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_set_transaction_status(scb, CAM_REQUEUE_REQ);
aic_freeze_scb(scb);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
if ((ahd->msg_flags & MSG_FLAG_IU_REQ_CHANGED) != 0) {
ahd_abort_scbs(ahd, SCB_GET_TARGET(ahd, scb),
SCB_GET_CHANNEL(ahd, scb),
SCB_GET_LUN(scb), SCB_LIST_NULL,
ROLE_INITIATOR, CAM_REQ_ABORTED);
} else {
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
#ifdef AHD_DEBUG
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
if ((ahd_debug & AHD_SHOW_MESSAGES) != 0)
printf("PPR Negotiation Busfree.\n");
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
#endif
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
ahd_done(ahd, scb);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
printerror = 0;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
if (printerror != 0) {
int aborted;
aborted = 0;
if (scb != NULL) {
u_int tag;
if ((scb->hscb->control & TAG_ENB) != 0)
tag = SCB_GET_TAG(scb);
else
tag = SCB_LIST_NULL;
ahd_print_path(ahd, scb);
aborted = ahd_abort_scbs(ahd, target, 'A',
SCB_GET_LUN(scb), tag,
ROLE_INITIATOR,
CAM_UNEXP_BUSFREE);
} else {
/*
* We had not fully identified this connection,
* so we cannot abort anything.
*/
printf("%s: ", ahd_name(ahd));
}
if (lastphase != P_BUSFREE)
ahd_force_renegotiation(ahd, &devinfo);
printf("Unexpected busfree %s, %d SCBs aborted, "
"PRGMCNT == 0x%x\n",
ahd_lookup_phase_entry(lastphase)->phasemsg,
aborted,
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
ahd_inw(ahd, PRGMCNT));
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_dump_card_state(ahd);
}
/* Always restart the sequencer. */
return (1);
}
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
static void
ahd_handle_proto_violation(struct ahd_softc *ahd)
{
struct ahd_devinfo devinfo;
struct scb *scb;
u_int scbid;
u_int seq_flags;
u_int curphase;
u_int lastphase;
int found;
ahd_fetch_devinfo(ahd, &devinfo);
scbid = ahd_get_scbptr(ahd);
scb = ahd_lookup_scb(ahd, scbid);
seq_flags = ahd_inb(ahd, SEQ_FLAGS);
curphase = ahd_inb(ahd, SCSISIGI) & PHASE_MASK;
lastphase = ahd_inb(ahd, LASTPHASE);
if ((seq_flags & NOT_IDENTIFIED) != 0) {
/*
* The reconnecting target either did not send an
* identify message, or did, but we didn't find an SCB
* to match.
*/
ahd_print_devinfo(ahd, &devinfo);
printf("Target did not send an IDENTIFY message. "
"LASTPHASE = 0x%x.\n", lastphase);
scb = NULL;
} else if (scb == NULL) {
/*
* We don't seem to have an SCB active for this
* transaction. Print an error and reset the bus.
*/
ahd_print_devinfo(ahd, &devinfo);
printf("No SCB found during protocol violation\n");
goto proto_violation_reset;
} else {
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_set_transaction_status(scb, CAM_SEQUENCE_FAIL);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
if ((seq_flags & NO_CDB_SENT) != 0) {
ahd_print_path(ahd, scb);
printf("No or incomplete CDB sent to device.\n");
aic79xx.c: Include read streaming in the PPR flags we display in diagnostics. In ahd_reset(), set the known mode after our initial pause prior to setting the mode. We can't just set the mode directly because the current mode, after the pause, is most likely unknown and setting the mode when the saved mode is unknown will trigger an assertion in the mode debug code. Complete an audit for SCB RAM reads. These reads must be performed via the special ahd_in?_scbram() methods so we can perform a Rev A. PCI-X workaround. Remove a superfluous mode save operation that was performed just prior to a call to ahd_clear_critical_section(). The saved mode was never restored and wouldn't have been valid anyway since the mode could change while single stepping out of a critical section. aic79xx.h: Add new BUG definition AHD_PCIX_SCBRAM_RD_BUG. aic79xx_inline.h: Update ahd_inb_scbram routine to check for AHD_PCIX_SCBRAM_RD_BUG and only apply the workaround if this bug is active. The old code applied the workaround in all cases. aic79xx_pci.c: Set AHD_PCIX_SCBRAM_RD_BUG for the A4. Remove an attempted saved_modes call in ahd_pci_test_register_access(). Saving the modes can only occur when we are paused, but the call was happening before the chip was known to be paused. Restoring the modes doesn't make sense either since the code makes no assumptions about the state of the sequencer until the first time the mode is set by the driver. This happens after the registers are successfully mapped.
2003-03-06 23:58:34 +00:00
} else if ((ahd_inb_scbram(ahd, SCB_CONTROL)
& STATUS_RCVD) == 0) {
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
/*
* The target never bothered to provide status to
* us prior to completing the command. Since we don't
* know the disposition of this command, we must attempt
* to abort it. Assert ATN and prepare to send an abort
* message.
*/
ahd_print_path(ahd, scb);
printf("Completed command without status.\n");
} else {
ahd_print_path(ahd, scb);
printf("Unknown protocol violation.\n");
ahd_dump_card_state(ahd);
}
}
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
if ((lastphase & ~P_DATAIN_DT) == 0
|| lastphase == P_COMMAND) {
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
proto_violation_reset:
/*
* Target either went directly to data
* phase or didn't respond to our ATN.
* The only safe thing to do is to blow
* it away with a bus reset.
*/
found = ahd_reset_channel(ahd, 'A', TRUE);
printf("%s: Issued Channel %c Bus Reset. "
"%d SCBs aborted\n", ahd_name(ahd), 'A', found);
} else {
/*
* Leave the selection hardware off in case
* this abort attempt will affect yet to
* be sent commands.
*/
ahd_outb(ahd, SCSISEQ0,
ahd_inb(ahd, SCSISEQ0) & ~ENSELO);
ahd_assert_atn(ahd);
ahd_outb(ahd, MSG_OUT, HOST_MSG);
if (scb == NULL) {
ahd_print_devinfo(ahd, &devinfo);
ahd->msgout_buf[0] = MSG_ABORT_TASK;
ahd->msgout_len = 1;
ahd->msgout_index = 0;
ahd->msg_type = MSG_TYPE_INITIATOR_MSGOUT;
} else {
ahd_print_path(ahd, scb);
scb->flags |= SCB_ABORT;
}
printf("Protocol violation %s. Attempting to abort.\n",
ahd_lookup_phase_entry(curphase)->phasemsg);
}
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*
* Force renegotiation to occur the next time we initiate
* a command to the current device.
*/
static void
ahd_force_renegotiation(struct ahd_softc *ahd, struct ahd_devinfo *devinfo)
{
struct ahd_initiator_tinfo *targ_info;
struct ahd_tmode_tstate *tstate;
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_MESSAGES) != 0) {
ahd_print_devinfo(ahd, devinfo);
printf("Forcing renegotiation\n");
}
#endif
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
targ_info = ahd_fetch_transinfo(ahd,
devinfo->channel,
devinfo->our_scsiid,
devinfo->target,
&tstate);
ahd_update_neg_request(ahd, devinfo, tstate,
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
targ_info, AHD_NEG_IF_NON_ASYNC);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
#define AHD_MAX_STEPS 2000
void
ahd_clear_critical_section(struct ahd_softc *ahd)
{
ahd_mode_state saved_modes;
int stepping;
int steps;
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
int first_instr;
u_int simode0;
u_int simode1;
u_int simode3;
u_int lqimode0;
u_int lqimode1;
u_int lqomode0;
u_int lqomode1;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if (ahd->num_critical_sections == 0)
return;
stepping = FALSE;
steps = 0;
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
first_instr = 0;
simode0 = 0;
simode1 = 0;
simode3 = 0;
lqimode0 = 0;
lqimode1 = 0;
lqomode0 = 0;
lqomode1 = 0;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
saved_modes = ahd_save_modes(ahd);
for (;;) {
struct cs *cs;
u_int seqaddr;
u_int i;
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
seqaddr = ahd_inw(ahd, CURADDR);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
cs = ahd->critical_sections;
for (i = 0; i < ahd->num_critical_sections; i++, cs++) {
if (cs->begin < seqaddr && cs->end >= seqaddr)
break;
}
if (i == ahd->num_critical_sections)
break;
if (steps > AHD_MAX_STEPS) {
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
printf("%s: Infinite loop in critical section\n"
"%s: First Instruction 0x%x now 0x%x\n",
ahd_name(ahd), ahd_name(ahd), first_instr,
seqaddr);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_dump_card_state(ahd);
panic("critical section loop");
}
steps++;
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_MISC) != 0)
printf("%s: Single stepping at 0x%x\n", ahd_name(ahd),
seqaddr);
#endif
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if (stepping == FALSE) {
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
first_instr = seqaddr;
ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG);
simode0 = ahd_inb(ahd, SIMODE0);
simode3 = ahd_inb(ahd, SIMODE3);
lqimode0 = ahd_inb(ahd, LQIMODE0);
lqimode1 = ahd_inb(ahd, LQIMODE1);
lqomode0 = ahd_inb(ahd, LQOMODE0);
lqomode1 = ahd_inb(ahd, LQOMODE1);
ahd_outb(ahd, SIMODE0, 0);
ahd_outb(ahd, SIMODE3, 0);
ahd_outb(ahd, LQIMODE0, 0);
ahd_outb(ahd, LQIMODE1, 0);
ahd_outb(ahd, LQOMODE0, 0);
ahd_outb(ahd, LQOMODE1, 0);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
Correct a typo in a comment. Add a comment in ahd_clear_critical_sections() about our need to leave ENBUSFREE set in SIMODE1 while single stepping. Re-arrange some delay loops so that we always perform a read after any register write and before the delay. This should make the delay loop more accurate. When completing message processing for a packetized commention, return the controller to a state where invalid non-packetized phases will still cause protocol violations. These are the same operations as those performed in the clear_target_state routine in the firmware. Now that we have a chip with working ABORTPENDING support (the 7901B), comment out the automatic use of this feature until we can adequately test it. The previous checkin updated the bug mask for the 7901B so this code was exercised. When resetting the bus, perform an ahd_flush_device_writes() call so that our reset assertion delay is acurately timed from when the reset bit is written to the controller.
2003-06-28 04:42:11 +00:00
simode1 = ahd_inb(ahd, SIMODE1);
/*
* We don't clear ENBUSFREE. Unfortunately
* we cannot re-enable busfree detection within
* the current connection, so we must leave it
* on while single stepping.
*/
ahd_outb(ahd, SIMODE1, simode1 & ENBUSFREE);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_outb(ahd, SEQCTL0, ahd_inb(ahd, SEQCTL0) | STEP);
stepping = TRUE;
}
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
ahd_outb(ahd, CLRSINT1, CLRBUSFREE);
ahd_outb(ahd, CLRINT, CLRSCSIINT);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_set_modes(ahd, ahd->saved_src_mode, ahd->saved_dst_mode);
ahd_outb(ahd, HCNTRL, ahd->unpause);
Correct a typo in a comment. Add a comment in ahd_clear_critical_sections() about our need to leave ENBUSFREE set in SIMODE1 while single stepping. Re-arrange some delay loops so that we always perform a read after any register write and before the delay. This should make the delay loop more accurate. When completing message processing for a packetized commention, return the controller to a state where invalid non-packetized phases will still cause protocol violations. These are the same operations as those performed in the clear_target_state routine in the firmware. Now that we have a chip with working ABORTPENDING support (the 7901B), comment out the automatic use of this feature until we can adequately test it. The previous checkin updated the bug mask for the 7901B so this code was exercised. When resetting the bus, perform an ahd_flush_device_writes() call so that our reset assertion delay is acurately timed from when the reset bit is written to the controller.
2003-06-28 04:42:11 +00:00
while (!ahd_is_paused(ahd))
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_delay(200);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_update_modes(ahd);
}
if (stepping) {
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG);
ahd_outb(ahd, SIMODE0, simode0);
ahd_outb(ahd, SIMODE3, simode3);
ahd_outb(ahd, LQIMODE0, lqimode0);
ahd_outb(ahd, LQIMODE1, lqimode1);
ahd_outb(ahd, LQOMODE0, lqomode0);
ahd_outb(ahd, LQOMODE1, lqomode1);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
ahd_outb(ahd, SEQCTL0, ahd_inb(ahd, SEQCTL0) & ~STEP);
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
ahd_outb(ahd, SIMODE1, simode1);
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
/*
* SCSIINT seems to glitch occassionally when
* the interrupt masks are restored. Clear SCSIINT
* one more time so that only persistent errors
* are seen as a real interrupt.
*/
ahd_outb(ahd, CLRINT, CLRSCSIINT);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
ahd_restore_modes(ahd, saved_modes);
}
/*
* Clear any pending interrupt status.
*/
void
ahd_clear_intstat(struct ahd_softc *ahd)
{
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
AHD_ASSERT_MODES(ahd, ~(AHD_MODE_UNKNOWN_MSK|AHD_MODE_CFG_MSK),
~(AHD_MODE_UNKNOWN_MSK|AHD_MODE_CFG_MSK));
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/* Clear any interrupt conditions this may have caused */
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
ahd_outb(ahd, CLRLQIINT0, CLRLQIATNQAS|CLRLQICRCT1|CLRLQICRCT2
|CLRLQIBADLQT|CLRLQIATNLQ|CLRLQIATNCMD);
ahd_outb(ahd, CLRLQIINT1, CLRLQIPHASE_LQ|CLRLQIPHASE_NLQ|CLRLIQABORT
|CLRLQICRCI_LQ|CLRLQICRCI_NLQ|CLRLQIBADLQI
|CLRLQIOVERI_LQ|CLRLQIOVERI_NLQ|CLRNONPACKREQ);
ahd_outb(ahd, CLRLQOINT0, CLRLQOTARGSCBPERR|CLRLQOSTOPT2|CLRLQOATNLQ
|CLRLQOATNPKT|CLRLQOTCRC);
ahd_outb(ahd, CLRLQOINT1, CLRLQOINITSCBPERR|CLRLQOSTOPI2|CLRLQOBADQAS
|CLRLQOBUSFREE|CLRLQOPHACHGINPKT);
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
if ((ahd->bugs & AHD_CLRLQO_AUTOCLR_BUG) != 0) {
ahd_outb(ahd, CLRLQOINT0, 0);
ahd_outb(ahd, CLRLQOINT1, 0);
}
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
ahd_outb(ahd, CLRSINT3, CLRNTRAMPERR|CLROSRAMPERR);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_outb(ahd, CLRSINT1, CLRSELTIMEO|CLRATNO|CLRSCSIRSTI
|CLRBUSFREE|CLRSCSIPERR|CLRREQINIT);
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
ahd_outb(ahd, CLRSINT0, CLRSELDO|CLRSELDI|CLRSELINGO
|CLRIOERR|CLROVERRUN);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_outb(ahd, CLRINT, CLRSCSIINT);
}
/**************************** Debugging Routines ******************************/
#ifdef AHD_DEBUG
uint32_t ahd_debug = AHD_DEBUG_OPTS;
#endif
void
ahd_print_scb(struct scb *scb)
{
struct hardware_scb *hscb;
int i;
hscb = scb->hscb;
printf("scb:%p control:0x%x scsiid:0x%x lun:%d cdb_len:%d\n",
(void *)scb,
hscb->control,
hscb->scsiid,
hscb->lun,
hscb->cdb_len);
printf("Shared Data: ");
for (i = 0; i < sizeof(hscb->shared_data.idata.cdb); i++)
printf("%#02x", hscb->shared_data.idata.cdb[i]);
printf(" dataptr:%#x%x datacnt:%#x sgptr:%#x tag:%#x\n",
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
(uint32_t)((aic_le64toh(hscb->dataptr) >> 32) & 0xFFFFFFFF),
(uint32_t)(aic_le64toh(hscb->dataptr) & 0xFFFFFFFF),
aic_le32toh(hscb->datacnt),
aic_le32toh(hscb->sgptr),
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
SCB_GET_TAG(scb));
ahd_dump_sglist(scb);
}
void
ahd_dump_sglist(struct scb *scb)
{
int i;
if (scb->sg_count > 0) {
if ((scb->ahd_softc->flags & AHD_64BIT_ADDRESSING) != 0) {
struct ahd_dma64_seg *sg_list;
sg_list = (struct ahd_dma64_seg*)scb->sg_list;
for (i = 0; i < scb->sg_count; i++) {
uint64_t addr;
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
uint32_t len;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
addr = aic_le64toh(sg_list[i].addr);
len = aic_le32toh(sg_list[i].len);
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
printf("sg[%d] - Addr 0x%x%x : Length %d%s\n",
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
i,
(uint32_t)((addr >> 32) & 0xFFFFFFFF),
(uint32_t)(addr & 0xFFFFFFFF),
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
sg_list[i].len & AHD_SG_LEN_MASK,
(sg_list[i].len & AHD_DMA_LAST_SEG)
? " Last" : "");
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
} else {
struct ahd_dma_seg *sg_list;
sg_list = (struct ahd_dma_seg*)scb->sg_list;
for (i = 0; i < scb->sg_count; i++) {
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
uint32_t len;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
len = aic_le32toh(sg_list[i].len);
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
printf("sg[%d] - Addr 0x%x%x : Length %d%s\n",
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
i,
aic79xx.h: Add softc flag to indicate that we have seen at least one selection since the last bus reset or SE/LVD bus change. aic79xx.c: Fix a few style nits. In ahd_update_pending_scbs(), only touch card registers once we have found an SCB that needs to be updated. This removes lots of clutter from PCI traces taken of error recovery performed by the driver. Short circuit the first selection iocell workaround handler if we've run once since the last bus reset or iocell change. This also removes clutter from PCI traces. Note if completions are pending in the qoutfifo when we dump card state.
2003-06-28 04:45:25 +00:00
(len & AHD_SG_HIGH_ADDR_MASK) >> 24,
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_le32toh(sg_list[i].addr),
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
len & AHD_SG_LEN_MASK,
len & AHD_DMA_LAST_SEG ? " Last" : "");
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
}
}
}
/************************* Transfer Negotiation *******************************/
/*
* Allocate per target mode instance (ID we respond to as a target)
* transfer negotiation data structures.
*/
static struct ahd_tmode_tstate *
ahd_alloc_tstate(struct ahd_softc *ahd, u_int scsi_id, char channel)
{
struct ahd_tmode_tstate *master_tstate;
struct ahd_tmode_tstate *tstate;
int i;
master_tstate = ahd->enabled_targets[ahd->our_id];
if (ahd->enabled_targets[scsi_id] != NULL
&& ahd->enabled_targets[scsi_id] != master_tstate)
panic("%s: ahd_alloc_tstate - Target already allocated",
ahd_name(ahd));
tstate = malloc(sizeof(*tstate), M_DEVBUF, M_NOWAIT);
if (tstate == NULL)
return (NULL);
/*
* If we have allocated a master tstate, copy user settings from
* the master tstate (taken from SRAM or the EEPROM) for this
* channel, but reset our current and goal settings to async/narrow
* until an initiator talks to us.
*/
if (master_tstate != NULL) {
memcpy(tstate, master_tstate, sizeof(*tstate));
memset(tstate->enabled_luns, 0, sizeof(tstate->enabled_luns));
for (i = 0; i < 16; i++) {
memset(&tstate->transinfo[i].curr, 0,
sizeof(tstate->transinfo[i].curr));
memset(&tstate->transinfo[i].goal, 0,
sizeof(tstate->transinfo[i].goal));
}
} else
memset(tstate, 0, sizeof(*tstate));
ahd->enabled_targets[scsi_id] = tstate;
return (tstate);
}
#ifdef AHD_TARGET_MODE
/*
* Free per target mode instance (ID we respond to as a target)
* transfer negotiation data structures.
*/
static void
ahd_free_tstate(struct ahd_softc *ahd, u_int scsi_id, char channel, int force)
{
struct ahd_tmode_tstate *tstate;
/*
* Don't clean up our "master" tstate.
* It has our default user settings.
*/
if (scsi_id == ahd->our_id
&& force == FALSE)
return;
tstate = ahd->enabled_targets[scsi_id];
if (tstate != NULL)
free(tstate, M_DEVBUF);
ahd->enabled_targets[scsi_id] = NULL;
}
#endif
/*
* Called when we have an active connection to a target on the bus,
* this function finds the nearest period to the input period limited
* by the capabilities of the bus connectivity of and sync settings for
* the target.
*/
void
ahd_devlimited_syncrate(struct ahd_softc *ahd,
struct ahd_initiator_tinfo *tinfo,
u_int *period, u_int *ppr_options, role_t role)
{
struct ahd_transinfo *transinfo;
u_int maxsync;
if ((ahd_inb(ahd, SBLKCTL) & ENAB40) != 0
&& (ahd_inb(ahd, SSTAT2) & EXP_ACTIVE) == 0) {
maxsync = AHD_SYNCRATE_PACED;
} else {
maxsync = AHD_SYNCRATE_ULTRA;
/* Can't do DT related options on an SE bus */
*ppr_options &= MSG_EXT_PPR_QAS_REQ;
}
/*
* Never allow a value higher than our current goal
* period otherwise we may allow a target initiated
* negotiation to go above the limit as set by the
* user. In the case of an initiator initiated
* sync negotiation, we limit based on the user
* setting. This allows the system to still accept
* incoming negotiations even if target initiated
* negotiation is not performed.
*/
if (role == ROLE_TARGET)
transinfo = &tinfo->user;
else
transinfo = &tinfo->goal;
*ppr_options &= (transinfo->ppr_options|MSG_EXT_PPR_PCOMP_EN);
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
if (transinfo->width == MSG_EXT_WDTR_BUS_8_BIT) {
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
maxsync = MAX(maxsync, AHD_SYNCRATE_ULTRA2);
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
*ppr_options &= ~MSG_EXT_PPR_DT_REQ;
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if (transinfo->period == 0) {
*period = 0;
*ppr_options = 0;
} else {
*period = MAX(*period, transinfo->period);
ahd_find_syncrate(ahd, period, ppr_options, maxsync);
}
}
/*
* Look up the valid period to SCSIRATE conversion in our table.
* Return the period and offset that should be sent to the target
* if this was the beginning of an SDTR.
*/
void
ahd_find_syncrate(struct ahd_softc *ahd, u_int *period,
u_int *ppr_options, u_int maxsync)
{
if (*period < maxsync)
*period = maxsync;
if ((*ppr_options & MSG_EXT_PPR_DT_REQ) != 0
&& *period > AHD_SYNCRATE_MIN_DT)
*ppr_options &= ~MSG_EXT_PPR_DT_REQ;
if (*period > AHD_SYNCRATE_MIN)
*period = 0;
/* Honor PPR option conformance rules. */
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
if (*period > AHD_SYNCRATE_PACED)
*ppr_options &= ~MSG_EXT_PPR_RTI;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if ((*ppr_options & MSG_EXT_PPR_IU_REQ) == 0)
*ppr_options &= (MSG_EXT_PPR_DT_REQ|MSG_EXT_PPR_QAS_REQ);
if ((*ppr_options & MSG_EXT_PPR_DT_REQ) == 0)
*ppr_options &= MSG_EXT_PPR_QAS_REQ;
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
/* Skip all PACED only entries if IU is not available */
if ((*ppr_options & MSG_EXT_PPR_IU_REQ) == 0
&& *period < AHD_SYNCRATE_DT)
*period = AHD_SYNCRATE_DT;
/* Skip all DT only entries if DT is not available */
if ((*ppr_options & MSG_EXT_PPR_DT_REQ) == 0
&& *period < AHD_SYNCRATE_ULTRA2)
*period = AHD_SYNCRATE_ULTRA2;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
/*
* Truncate the given synchronous offset to a value the
* current adapter type and syncrate are capable of.
*/
void
ahd_validate_offset(struct ahd_softc *ahd,
struct ahd_initiator_tinfo *tinfo,
u_int period, u_int *offset, int wide,
role_t role)
{
u_int maxoffset;
/* Limit offset to what we can do */
if (period == 0)
maxoffset = 0;
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
else if (period <= AHD_SYNCRATE_PACED) {
if ((ahd->bugs & AHD_PACED_NEGTABLE_BUG) != 0)
maxoffset = MAX_OFFSET_PACED_BUG;
else
maxoffset = MAX_OFFSET_PACED;
} else
maxoffset = MAX_OFFSET_NON_PACED;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
*offset = MIN(*offset, maxoffset);
if (tinfo != NULL) {
if (role == ROLE_TARGET)
*offset = MIN(*offset, tinfo->user.offset);
else
*offset = MIN(*offset, tinfo->goal.offset);
}
}
/*
* Truncate the given transfer width parameter to a value the
* current adapter type is capable of.
*/
void
ahd_validate_width(struct ahd_softc *ahd, struct ahd_initiator_tinfo *tinfo,
u_int *bus_width, role_t role)
{
switch (*bus_width) {
default:
if (ahd->features & AHD_WIDE) {
/* Respond Wide */
*bus_width = MSG_EXT_WDTR_BUS_16_BIT;
break;
}
/* FALLTHROUGH */
case MSG_EXT_WDTR_BUS_8_BIT:
*bus_width = MSG_EXT_WDTR_BUS_8_BIT;
break;
}
if (tinfo != NULL) {
if (role == ROLE_TARGET)
*bus_width = MIN(tinfo->user.width, *bus_width);
else
*bus_width = MIN(tinfo->goal.width, *bus_width);
}
}
/*
* Update the bitmask of targets for which the controller should
* negotiate with at the next convenient oportunity. This currently
* means the next time we send the initial identify messages for
* a new transaction.
*/
int
ahd_update_neg_request(struct ahd_softc *ahd, struct ahd_devinfo *devinfo,
struct ahd_tmode_tstate *tstate,
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
struct ahd_initiator_tinfo *tinfo, ahd_neg_type neg_type)
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
{
u_int auto_negotiate_orig;
auto_negotiate_orig = tstate->auto_negotiate;
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
if (neg_type == AHD_NEG_ALWAYS) {
/*
* Force our "current" settings to be
* unknown so that unless a bus reset
* occurs the need to renegotiate is
* recorded persistently.
*/
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
if ((ahd->features & AHD_WIDE) != 0)
tinfo->curr.width = AHD_WIDTH_UNKNOWN;
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
tinfo->curr.period = AHD_PERIOD_UNKNOWN;
tinfo->curr.offset = AHD_OFFSET_UNKNOWN;
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if (tinfo->curr.period != tinfo->goal.period
|| tinfo->curr.width != tinfo->goal.width
|| tinfo->curr.offset != tinfo->goal.offset
|| tinfo->curr.ppr_options != tinfo->goal.ppr_options
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
|| (neg_type == AHD_NEG_IF_NON_ASYNC
&& (tinfo->goal.offset != 0
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
|| tinfo->goal.width != MSG_EXT_WDTR_BUS_8_BIT
|| tinfo->goal.ppr_options != 0)))
tstate->auto_negotiate |= devinfo->target_mask;
else
tstate->auto_negotiate &= ~devinfo->target_mask;
return (auto_negotiate_orig != tstate->auto_negotiate);
}
/*
* Update the user/goal/curr tables of synchronous negotiation
* parameters as well as, in the case of a current or active update,
* any data structures on the host controller. In the case of an
* active update, the specified target is currently talking to us on
* the bus, so the transfer parameter update must take effect
* immediately.
*/
void
ahd_set_syncrate(struct ahd_softc *ahd, struct ahd_devinfo *devinfo,
u_int period, u_int offset, u_int ppr_options,
u_int type, int paused)
{
struct ahd_initiator_tinfo *tinfo;
struct ahd_tmode_tstate *tstate;
u_int old_period;
u_int old_offset;
u_int old_ppr;
int active;
int update_needed;
active = (type & AHD_TRANS_ACTIVE) == AHD_TRANS_ACTIVE;
update_needed = 0;
if (period == 0 || offset == 0) {
period = 0;
offset = 0;
}
tinfo = ahd_fetch_transinfo(ahd, devinfo->channel, devinfo->our_scsiid,
devinfo->target, &tstate);
if ((type & AHD_TRANS_USER) != 0) {
tinfo->user.period = period;
tinfo->user.offset = offset;
tinfo->user.ppr_options = ppr_options;
}
if ((type & AHD_TRANS_GOAL) != 0) {
tinfo->goal.period = period;
tinfo->goal.offset = offset;
tinfo->goal.ppr_options = ppr_options;
}
old_period = tinfo->curr.period;
old_offset = tinfo->curr.offset;
old_ppr = tinfo->curr.ppr_options;
if ((type & AHD_TRANS_CUR) != 0
&& (old_period != period
|| old_offset != offset
|| old_ppr != ppr_options)) {
update_needed++;
tinfo->curr.period = period;
tinfo->curr.offset = offset;
tinfo->curr.ppr_options = ppr_options;
ahd_send_async(ahd, devinfo->channel, devinfo->target,
CAM_LUN_WILDCARD, AC_TRANSFER_NEG, NULL);
if (bootverbose) {
if (offset != 0) {
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
int options;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
printf("%s: target %d synchronous with "
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
"period = 0x%x, offset = 0x%x",
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_name(ahd), devinfo->target,
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
period, offset);
options = 0;
aic79xx.c: Include read streaming in the PPR flags we display in diagnostics. In ahd_reset(), set the known mode after our initial pause prior to setting the mode. We can't just set the mode directly because the current mode, after the pause, is most likely unknown and setting the mode when the saved mode is unknown will trigger an assertion in the mode debug code. Complete an audit for SCB RAM reads. These reads must be performed via the special ahd_in?_scbram() methods so we can perform a Rev A. PCI-X workaround. Remove a superfluous mode save operation that was performed just prior to a call to ahd_clear_critical_section(). The saved mode was never restored and wouldn't have been valid anyway since the mode could change while single stepping out of a critical section. aic79xx.h: Add new BUG definition AHD_PCIX_SCBRAM_RD_BUG. aic79xx_inline.h: Update ahd_inb_scbram routine to check for AHD_PCIX_SCBRAM_RD_BUG and only apply the workaround if this bug is active. The old code applied the workaround in all cases. aic79xx_pci.c: Set AHD_PCIX_SCBRAM_RD_BUG for the A4. Remove an attempted saved_modes call in ahd_pci_test_register_access(). Saving the modes can only occur when we are paused, but the call was happening before the chip was known to be paused. Restoring the modes doesn't make sense either since the code makes no assumptions about the state of the sequencer until the first time the mode is set by the driver. This happens after the registers are successfully mapped.
2003-03-06 23:58:34 +00:00
if ((ppr_options & MSG_EXT_PPR_RD_STRM) != 0) {
printf("(RDSTRM");
options++;
}
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
if ((ppr_options & MSG_EXT_PPR_DT_REQ) != 0) {
aic79xx.c: Include read streaming in the PPR flags we display in diagnostics. In ahd_reset(), set the known mode after our initial pause prior to setting the mode. We can't just set the mode directly because the current mode, after the pause, is most likely unknown and setting the mode when the saved mode is unknown will trigger an assertion in the mode debug code. Complete an audit for SCB RAM reads. These reads must be performed via the special ahd_in?_scbram() methods so we can perform a Rev A. PCI-X workaround. Remove a superfluous mode save operation that was performed just prior to a call to ahd_clear_critical_section(). The saved mode was never restored and wouldn't have been valid anyway since the mode could change while single stepping out of a critical section. aic79xx.h: Add new BUG definition AHD_PCIX_SCBRAM_RD_BUG. aic79xx_inline.h: Update ahd_inb_scbram routine to check for AHD_PCIX_SCBRAM_RD_BUG and only apply the workaround if this bug is active. The old code applied the workaround in all cases. aic79xx_pci.c: Set AHD_PCIX_SCBRAM_RD_BUG for the A4. Remove an attempted saved_modes call in ahd_pci_test_register_access(). Saving the modes can only occur when we are paused, but the call was happening before the chip was known to be paused. Restoring the modes doesn't make sense either since the code makes no assumptions about the state of the sequencer until the first time the mode is set by the driver. This happens after the registers are successfully mapped.
2003-03-06 23:58:34 +00:00
printf("%s", options ? "|DT" : "(DT");
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
options++;
}
if ((ppr_options & MSG_EXT_PPR_IU_REQ) != 0) {
printf("%s", options ? "|IU" : "(IU");
options++;
}
if ((ppr_options & MSG_EXT_PPR_RTI) != 0) {
printf("%s", options ? "|RTI" : "(RTI");
options++;
}
if ((ppr_options & MSG_EXT_PPR_QAS_REQ) != 0) {
printf("%s", options ? "|QAS" : "(QAS");
options++;
}
if (options != 0)
printf(")\n");
else
printf("\n");
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
} else {
printf("%s: target %d using "
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
"asynchronous transfers%s\n",
ahd_name(ahd), devinfo->target,
(ppr_options & MSG_EXT_PPR_QAS_REQ) != 0
? "(QAS)" : "");
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
}
}
/*
* Always refresh the neg-table to handle the case of the
* sequencer setting the ENATNO bit for a MK_MESSAGE request.
* We will always renegotiate in that case if this is a
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
* packetized request. Also manage the busfree expected flag
* from this common routine so that we catch changes due to
* WDTR or SDTR messages.
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
*/
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
if ((type & AHD_TRANS_CUR) != 0) {
if (!paused)
ahd_pause(ahd);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_update_neg_table(ahd, devinfo, &tinfo->curr);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
if (!paused)
ahd_unpause(ahd);
if (ahd->msg_type != MSG_TYPE_NONE) {
if ((old_ppr & MSG_EXT_PPR_IU_REQ)
!= (ppr_options & MSG_EXT_PPR_IU_REQ)) {
#ifdef AHD_DEBUG
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
if ((ahd_debug & AHD_SHOW_MESSAGES) != 0) {
ahd_print_devinfo(ahd, devinfo);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
printf("Expecting IU Change busfree\n");
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
}
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
#endif
ahd->msg_flags |= MSG_FLAG_EXPECT_PPR_BUSFREE
| MSG_FLAG_IU_REQ_CHANGED;
}
if ((old_ppr & MSG_EXT_PPR_IU_REQ) != 0) {
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_MESSAGES) != 0)
printf("PPR with IU_REQ outstanding\n");
#endif
ahd->msg_flags |= MSG_FLAG_EXPECT_PPR_BUSFREE;
}
}
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
update_needed += ahd_update_neg_request(ahd, devinfo, tstate,
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
tinfo, AHD_NEG_TO_GOAL);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
if (update_needed && active)
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_update_pending_scbs(ahd);
}
/*
* Update the user/goal/curr tables of wide negotiation
* parameters as well as, in the case of a current or active update,
* any data structures on the host controller. In the case of an
* active update, the specified target is currently talking to us on
* the bus, so the transfer parameter update must take effect
* immediately.
*/
void
ahd_set_width(struct ahd_softc *ahd, struct ahd_devinfo *devinfo,
u_int width, u_int type, int paused)
{
struct ahd_initiator_tinfo *tinfo;
struct ahd_tmode_tstate *tstate;
u_int oldwidth;
int active;
int update_needed;
active = (type & AHD_TRANS_ACTIVE) == AHD_TRANS_ACTIVE;
update_needed = 0;
tinfo = ahd_fetch_transinfo(ahd, devinfo->channel, devinfo->our_scsiid,
devinfo->target, &tstate);
if ((type & AHD_TRANS_USER) != 0)
tinfo->user.width = width;
if ((type & AHD_TRANS_GOAL) != 0)
tinfo->goal.width = width;
oldwidth = tinfo->curr.width;
if ((type & AHD_TRANS_CUR) != 0 && oldwidth != width) {
update_needed++;
tinfo->curr.width = width;
ahd_send_async(ahd, devinfo->channel, devinfo->target,
CAM_LUN_WILDCARD, AC_TRANSFER_NEG, NULL);
if (bootverbose) {
printf("%s: target %d using %dbit transfers\n",
ahd_name(ahd), devinfo->target,
8 * (0x01 << width));
}
}
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
if ((type & AHD_TRANS_CUR) != 0) {
if (!paused)
ahd_pause(ahd);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_update_neg_table(ahd, devinfo, &tinfo->curr);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
if (!paused)
ahd_unpause(ahd);
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
update_needed += ahd_update_neg_request(ahd, devinfo, tstate,
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
tinfo, AHD_NEG_TO_GOAL);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
if (update_needed && active)
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_update_pending_scbs(ahd);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
/*
* Update the current state of tagged queuing for a given target.
*/
void
ahd_set_tags(struct ahd_softc *ahd, struct ahd_devinfo *devinfo,
ahd_queue_alg alg)
{
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
ahd_platform_set_tags(ahd, devinfo, alg);
ahd_send_async(ahd, devinfo->channel, devinfo->target,
devinfo->lun, AC_TRANSFER_NEG, &alg);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
static void
ahd_update_neg_table(struct ahd_softc *ahd, struct ahd_devinfo *devinfo,
struct ahd_transinfo *tinfo)
{
ahd_mode_state saved_modes;
u_int period;
u_int ppr_opts;
u_int con_opts;
u_int offset;
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
u_int saved_negoaddr;
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
uint8_t iocell_opts[sizeof(ahd->iocell_opts)];
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
saved_modes = ahd_save_modes(ahd);
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
saved_negoaddr = ahd_inb(ahd, NEGOADDR);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_outb(ahd, NEGOADDR, devinfo->target);
period = tinfo->period;
offset = tinfo->offset;
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
memcpy(iocell_opts, ahd->iocell_opts, sizeof(ahd->iocell_opts));
ppr_opts = tinfo->ppr_options & (MSG_EXT_PPR_QAS_REQ|MSG_EXT_PPR_DT_REQ
|MSG_EXT_PPR_IU_REQ|MSG_EXT_PPR_RTI);
con_opts = 0;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if (period == 0)
period = AHD_SYNCRATE_ASYNC;
if (period == AHD_SYNCRATE_160) {
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
if ((ahd->bugs & AHD_PACED_NEGTABLE_BUG) != 0) {
/*
* When the SPI4 spec was finalized, PACE transfers
* was not made a configurable option in the PPR
* message. Instead it is assumed to be enabled for
* any syncrate faster than 80MHz. Nevertheless,
* Harpoon2A4 allows this to be configurable.
*
* Harpoon2A4 also assumes at most 2 data bytes per
* negotiated REQ/ACK offset. Paced transfers take
* 4, so we must adjust our offset.
*/
ppr_opts |= PPROPT_PACE;
offset *= 2;
/*
* Harpoon2A assumed that there would be a
* fallback rate between 160MHz and 80Mhz,
* so 7 is used as the period factor rather
* than 8 for 160MHz.
*/
period = AHD_SYNCRATE_REVA_160;
}
if ((tinfo->ppr_options & MSG_EXT_PPR_PCOMP_EN) == 0)
iocell_opts[AHD_PRECOMP_SLEW_INDEX] &=
~AHD_PRECOMP_MASK;
} else {
/*
* Precomp should be disabled for non-paced transfers.
*/
iocell_opts[AHD_PRECOMP_SLEW_INDEX] &= ~AHD_PRECOMP_MASK;
if ((ahd->features & AHD_NEW_IOCELL_OPTS) != 0
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
&& (ppr_opts & MSG_EXT_PPR_DT_REQ) != 0
&& (ppr_opts & MSG_EXT_PPR_IU_REQ) == 0) {
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
/*
* Slow down our CRC interval to be
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
* compatible with non-packetized
* U160 devices that can't handle a
* CRC at full speed.
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
*/
con_opts |= ENSLOWCRC;
}
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
if ((ahd->bugs & AHD_PACED_NEGTABLE_BUG) != 0) {
/*
* On H2A4, revert to a slower slewrate
* on non-paced transfers.
*/
iocell_opts[AHD_PRECOMP_SLEW_INDEX] &=
~AHD_SLEWRATE_MASK;
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
ahd_outb(ahd, ANNEXCOL, AHD_ANNEXCOL_PRECOMP_SLEW);
ahd_outb(ahd, ANNEXDAT, iocell_opts[AHD_PRECOMP_SLEW_INDEX]);
ahd_outb(ahd, ANNEXCOL, AHD_ANNEXCOL_AMPLITUDE);
ahd_outb(ahd, ANNEXDAT, iocell_opts[AHD_AMPLITUDE_INDEX]);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_outb(ahd, NEGPERIOD, period);
ahd_outb(ahd, NEGPPROPTS, ppr_opts);
ahd_outb(ahd, NEGOFFSET, offset);
if (tinfo->width == MSG_EXT_WDTR_BUS_16_BIT)
con_opts |= WIDEXFER;
/*
* During packetized transfers, the target will
* give us the oportunity to send command packets
* without us asserting attention.
*/
if ((tinfo->ppr_options & MSG_EXT_PPR_IU_REQ) == 0)
con_opts |= ENAUTOATNO;
ahd_outb(ahd, NEGCONOPTS, con_opts);
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
ahd_outb(ahd, NEGOADDR, saved_negoaddr);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_restore_modes(ahd, saved_modes);
}
/*
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
* When the transfer settings for a connection change, setup for
* negotiation in pending SCBs to effect the change as quickly as
* possible. We also cancel any negotiations that are scheduled
* for inflight SCBs that have not been started yet.
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
*/
static void
ahd_update_pending_scbs(struct ahd_softc *ahd)
{
struct scb *pending_scb;
int pending_scb_count;
aic79xx.h: Add softc flag to indicate that we have seen at least one selection since the last bus reset or SE/LVD bus change. aic79xx.c: Fix a few style nits. In ahd_update_pending_scbs(), only touch card registers once we have found an SCB that needs to be updated. This removes lots of clutter from PCI traces taken of error recovery performed by the driver. Short circuit the first selection iocell workaround handler if we've run once since the last bus reset or iocell change. This also removes clutter from PCI traces. Note if completions are pending in the qoutfifo when we dump card state.
2003-06-28 04:45:25 +00:00
u_int scb_tag;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
int paused;
u_int saved_scbptr;
ahd_mode_state saved_modes;
/*
* Traverse the pending SCB list and ensure that all of the
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
* SCBs there have the proper settings. We can only safely
* clear the negotiation required flag (setting requires the
* execution queue to be modified) and this is only possible
* if we are not already attempting to select out for this
* SCB. For this reason, all callers only call this routine
* if we are changing the negotiation settings for the currently
* active transaction on the bus.
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
*/
pending_scb_count = 0;
LIST_FOREACH(pending_scb, &ahd->pending_scbs, pending_links) {
struct ahd_devinfo devinfo;
struct hardware_scb *pending_hscb;
struct ahd_initiator_tinfo *tinfo;
struct ahd_tmode_tstate *tstate;
ahd_scb_devinfo(ahd, &devinfo, pending_scb);
tinfo = ahd_fetch_transinfo(ahd, devinfo.channel,
devinfo.our_scsiid,
devinfo.target, &tstate);
pending_hscb = pending_scb->hscb;
if ((tstate->auto_negotiate & devinfo.target_mask) == 0
&& (pending_scb->flags & SCB_AUTO_NEGOTIATE) != 0) {
pending_scb->flags &= ~SCB_AUTO_NEGOTIATE;
pending_hscb->control &= ~MK_MESSAGE;
}
ahd_sync_scb(ahd, pending_scb,
BUS_DMASYNC_PREREAD|BUS_DMASYNC_PREWRITE);
pending_scb_count++;
}
if (pending_scb_count == 0)
return;
if (ahd_is_paused(ahd)) {
paused = 1;
} else {
paused = 0;
ahd_pause(ahd);
}
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
/*
* Force the sequencer to reinitialize the selection for
* the command at the head of the execution queue if it
* has already been setup. The negotiation changes may
* effect whether we select-out with ATN.
*/
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
saved_modes = ahd_save_modes(ahd);
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
ahd_outb(ahd, SCSISEQ0, ahd_inb(ahd, SCSISEQ0) & ~ENSELO);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
saved_scbptr = ahd_get_scbptr(ahd);
/* Ensure that the hscbs down on the card match the new information */
aic79xx.h: Add softc flag to indicate that we have seen at least one selection since the last bus reset or SE/LVD bus change. aic79xx.c: Fix a few style nits. In ahd_update_pending_scbs(), only touch card registers once we have found an SCB that needs to be updated. This removes lots of clutter from PCI traces taken of error recovery performed by the driver. Short circuit the first selection iocell workaround handler if we've run once since the last bus reset or iocell change. This also removes clutter from PCI traces. Note if completions are pending in the qoutfifo when we dump card state.
2003-06-28 04:45:25 +00:00
for (scb_tag = 0; scb_tag < ahd->scb_data.maxhscbs; scb_tag++) {
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
struct hardware_scb *pending_hscb;
u_int control;
pending_scb = ahd_lookup_scb(ahd, scb_tag);
if (pending_scb == NULL)
continue;
aic79xx.h: Add softc flag to indicate that we have seen at least one selection since the last bus reset or SE/LVD bus change. aic79xx.c: Fix a few style nits. In ahd_update_pending_scbs(), only touch card registers once we have found an SCB that needs to be updated. This removes lots of clutter from PCI traces taken of error recovery performed by the driver. Short circuit the first selection iocell workaround handler if we've run once since the last bus reset or iocell change. This also removes clutter from PCI traces. Note if completions are pending in the qoutfifo when we dump card state.
2003-06-28 04:45:25 +00:00
ahd_set_scbptr(ahd, scb_tag);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
pending_hscb = pending_scb->hscb;
control = ahd_inb_scbram(ahd, SCB_CONTROL);
control &= ~MK_MESSAGE;
control |= pending_hscb->control & MK_MESSAGE;
ahd_outb(ahd, SCB_CONTROL, control);
}
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
ahd_set_scbptr(ahd, saved_scbptr);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_restore_modes(ahd, saved_modes);
if (paused == 0)
ahd_unpause(ahd);
}
/**************************** Pathing Information *****************************/
static void
ahd_fetch_devinfo(struct ahd_softc *ahd, struct ahd_devinfo *devinfo)
{
ahd_mode_state saved_modes;
u_int saved_scsiid;
role_t role;
int our_id;
saved_modes = ahd_save_modes(ahd);
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
if (ahd_inb(ahd, SSTAT0) & TARGET)
role = ROLE_TARGET;
else
role = ROLE_INITIATOR;
if (role == ROLE_TARGET
&& (ahd_inb(ahd, SEQ_FLAGS) & CMDPHASE_PENDING) != 0) {
/* We were selected, so pull our id from TARGIDIN */
our_id = ahd_inb(ahd, TARGIDIN) & OID;
} else if (role == ROLE_TARGET)
our_id = ahd_inb(ahd, TOWNID);
else
our_id = ahd_inb(ahd, IOWNID);
saved_scsiid = ahd_inb(ahd, SAVED_SCSIID);
ahd_compile_devinfo(devinfo,
our_id,
SCSIID_TARGET(ahd, saved_scsiid),
ahd_inb(ahd, SAVED_LUN),
SCSIID_CHANNEL(ahd, saved_scsiid),
role);
ahd_restore_modes(ahd, saved_modes);
}
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
void
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
ahd_print_devinfo(struct ahd_softc *ahd, struct ahd_devinfo *devinfo)
{
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
printf("%s:%c:%d:%d: ", ahd_name(ahd), 'A',
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
devinfo->target, devinfo->lun);
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
struct ahd_phase_table_entry*
ahd_lookup_phase_entry(int phase)
{
struct ahd_phase_table_entry *entry;
struct ahd_phase_table_entry *last_entry;
/*
* num_phases doesn't include the default entry which
* will be returned if the phase doesn't match.
*/
last_entry = &ahd_phase_table[num_phases];
for (entry = ahd_phase_table; entry < last_entry; entry++) {
if (phase == entry->phase)
break;
}
return (entry);
}
void
ahd_compile_devinfo(struct ahd_devinfo *devinfo, u_int our_id, u_int target,
u_int lun, char channel, role_t role)
{
devinfo->our_scsiid = our_id;
devinfo->target = target;
devinfo->lun = lun;
devinfo->target_offset = target;
devinfo->channel = channel;
devinfo->role = role;
if (channel == 'B')
devinfo->target_offset += 8;
devinfo->target_mask = (0x01 << devinfo->target_offset);
}
static void
ahd_scb_devinfo(struct ahd_softc *ahd, struct ahd_devinfo *devinfo,
struct scb *scb)
{
role_t role;
int our_id;
our_id = SCSIID_OUR_ID(scb->hscb->scsiid);
role = ROLE_INITIATOR;
if ((scb->hscb->control & TARGET_SCB) != 0)
role = ROLE_TARGET;
ahd_compile_devinfo(devinfo, our_id, SCB_GET_TARGET(ahd, scb),
SCB_GET_LUN(scb), SCB_GET_CHANNEL(ahd, scb), role);
}
/************************ Message Phase Processing ****************************/
/*
* When an initiator transaction with the MK_MESSAGE flag either reconnects
* or enters the initial message out phase, we are interrupted. Fill our
* outgoing message buffer with the appropriate message and beging handing
* the message phase(s) manually.
*/
static void
ahd_setup_initiator_msgout(struct ahd_softc *ahd, struct ahd_devinfo *devinfo,
struct scb *scb)
{
/*
* To facilitate adding multiple messages together,
* each routine should increment the index and len
* variables instead of setting them explicitly.
*/
ahd->msgout_index = 0;
ahd->msgout_len = 0;
if (ahd_currently_packetized(ahd))
ahd->msg_flags |= MSG_FLAG_PACKETIZED;
if (ahd->send_msg_perror
&& ahd_inb(ahd, MSG_OUT) == HOST_MSG) {
ahd->msgout_buf[ahd->msgout_index++] = ahd->send_msg_perror;
ahd->msgout_len++;
ahd->msg_type = MSG_TYPE_INITIATOR_MSGOUT;
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_MESSAGES) != 0)
printf("Setting up for Parity Error delivery\n");
#endif
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
return;
} else if (scb == NULL) {
printf("%s: WARNING. No pending message for "
"I_T msgin. Issuing NO-OP\n", ahd_name(ahd));
ahd->msgout_buf[ahd->msgout_index++] = MSG_NOOP;
ahd->msgout_len++;
ahd->msg_type = MSG_TYPE_INITIATOR_MSGOUT;
return;
}
if ((scb->flags & SCB_DEVICE_RESET) == 0
&& (scb->flags & SCB_PACKETIZED) == 0
&& ahd_inb(ahd, MSG_OUT) == MSG_IDENTIFYFLAG) {
u_int identify_msg;
identify_msg = MSG_IDENTIFYFLAG | SCB_GET_LUN(scb);
if ((scb->hscb->control & DISCENB) != 0)
identify_msg |= MSG_IDENTIFY_DISCFLAG;
ahd->msgout_buf[ahd->msgout_index++] = identify_msg;
ahd->msgout_len++;
if ((scb->hscb->control & TAG_ENB) != 0) {
ahd->msgout_buf[ahd->msgout_index++] =
scb->hscb->control & (TAG_ENB|SCB_TAG_TYPE);
ahd->msgout_buf[ahd->msgout_index++] = SCB_GET_TAG(scb);
ahd->msgout_len += 2;
}
}
if (scb->flags & SCB_DEVICE_RESET) {
ahd->msgout_buf[ahd->msgout_index++] = MSG_BUS_DEV_RESET;
ahd->msgout_len++;
ahd_print_path(ahd, scb);
printf("Bus Device Reset Message Sent\n");
/*
* Clear our selection hardware in advance of
* the busfree. We may have an entry in the waiting
* Q for this target, and we don't want to go about
* selecting while we handle the busfree and blow it
* away.
*/
ahd_outb(ahd, SCSISEQ0, 0);
} else if ((scb->flags & SCB_ABORT) != 0) {
if ((scb->hscb->control & TAG_ENB) != 0) {
ahd->msgout_buf[ahd->msgout_index++] = MSG_ABORT_TAG;
} else {
ahd->msgout_buf[ahd->msgout_index++] = MSG_ABORT;
}
ahd->msgout_len++;
ahd_print_path(ahd, scb);
printf("Abort%s Message Sent\n",
(scb->hscb->control & TAG_ENB) != 0 ? " Tag" : "");
/*
* Clear our selection hardware in advance of
* the busfree. We may have an entry in the waiting
* Q for this target, and we don't want to go about
* selecting while we handle the busfree and blow it
* away.
*/
ahd_outb(ahd, SCSISEQ0, 0);
} else if ((scb->flags & (SCB_AUTO_NEGOTIATE|SCB_NEGOTIATE)) != 0) {
ahd_build_transfer_msg(ahd, devinfo);
/*
* Clear our selection hardware in advance of potential
* PPR IU status change busfree. We may have an entry in
* the waiting Q for this target, and we don't want to go
* about selecting while we handle the busfree and blow
* it away.
*/
ahd_outb(ahd, SCSISEQ0, 0);
} else {
printf("ahd_intr: AWAITING_MSG for an SCB that "
"does not have a waiting message\n");
printf("SCSIID = %x, target_mask = %x\n", scb->hscb->scsiid,
devinfo->target_mask);
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
panic("SCB = %d, SCB Control = %x:%x, MSG_OUT = %x "
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
"SCB flags = %x", SCB_GET_TAG(scb), scb->hscb->control,
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
ahd_inb_scbram(ahd, SCB_CONTROL), ahd_inb(ahd, MSG_OUT),
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
scb->flags);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
/*
* Clear the MK_MESSAGE flag from the SCB so we aren't
* asked to send this message again.
*/
ahd_outb(ahd, SCB_CONTROL,
ahd_inb_scbram(ahd, SCB_CONTROL) & ~MK_MESSAGE);
scb->hscb->control &= ~MK_MESSAGE;
ahd->msgout_index = 0;
ahd->msg_type = MSG_TYPE_INITIATOR_MSGOUT;
}
/*
* Build an appropriate transfer negotiation message for the
* currently active target.
*/
static void
ahd_build_transfer_msg(struct ahd_softc *ahd, struct ahd_devinfo *devinfo)
{
/*
* We need to initiate transfer negotiations.
* If our current and goal settings are identical,
* we want to renegotiate due to a check condition.
*/
struct ahd_initiator_tinfo *tinfo;
struct ahd_tmode_tstate *tstate;
int dowide;
int dosync;
int doppr;
u_int period;
u_int ppr_options;
u_int offset;
tinfo = ahd_fetch_transinfo(ahd, devinfo->channel, devinfo->our_scsiid,
devinfo->target, &tstate);
/*
* Filter our period based on the current connection.
* If we can't perform DT transfers on this segment (not in LVD
* mode for instance), then our decision to issue a PPR message
* may change.
*/
period = tinfo->goal.period;
Work around SCSI spec violation by the Quantum Atlas 10K. This drive delays going async after receiving a WDTR message. We now send an SDTR message after a WDTR even if our goal is to go async. This should work even for confused devices. If we get an unexpected busfree when attempting a WDTR or SDTR, only set the goal negotiation parameters we were trying to negotiate to off. This means that should a WDTR message fail, we will still try an SDTR if our goal is non-async. Fix a few more places where we were looking at goal.period instead of goal.offset for determining if we should be negotiating sync. This should not have any impact on our behavior, but the offset is more definitive and should be used.
2003-06-06 23:51:13 +00:00
offset = tinfo->goal.offset;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ppr_options = tinfo->goal.ppr_options;
/* Target initiated PPR is not allowed in the SCSI spec */
if (devinfo->role == ROLE_TARGET)
ppr_options = 0;
ahd_devlimited_syncrate(ahd, tinfo, &period,
&ppr_options, devinfo->role);
dowide = tinfo->curr.width != tinfo->goal.width;
Work around SCSI spec violation by the Quantum Atlas 10K. This drive delays going async after receiving a WDTR message. We now send an SDTR message after a WDTR even if our goal is to go async. This should work even for confused devices. If we get an unexpected busfree when attempting a WDTR or SDTR, only set the goal negotiation parameters we were trying to negotiate to off. This means that should a WDTR message fail, we will still try an SDTR if our goal is non-async. Fix a few more places where we were looking at goal.period instead of goal.offset for determining if we should be negotiating sync. This should not have any impact on our behavior, but the offset is more definitive and should be used.
2003-06-06 23:51:13 +00:00
dosync = tinfo->curr.offset != offset || tinfo->curr.period != period;
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
/*
* Only use PPR if we have options that need it, even if the device
* claims to support it. There might be an expander in the way
* that doesn't.
*/
doppr = ppr_options != 0;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if (!dowide && !dosync && !doppr) {
dowide = tinfo->goal.width != MSG_EXT_WDTR_BUS_8_BIT;
Work around SCSI spec violation by the Quantum Atlas 10K. This drive delays going async after receiving a WDTR message. We now send an SDTR message after a WDTR even if our goal is to go async. This should work even for confused devices. If we get an unexpected busfree when attempting a WDTR or SDTR, only set the goal negotiation parameters we were trying to negotiate to off. This means that should a WDTR message fail, we will still try an SDTR if our goal is non-async. Fix a few more places where we were looking at goal.period instead of goal.offset for determining if we should be negotiating sync. This should not have any impact on our behavior, but the offset is more definitive and should be used.
2003-06-06 23:51:13 +00:00
dosync = tinfo->goal.offset != 0;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
if (!dowide && !dosync && !doppr) {
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
/*
* Force async with a WDTR message if we have a wide bus,
* or just issue an SDTR with a 0 offset.
*/
if ((ahd->features & AHD_WIDE) != 0)
dowide = 1;
else
dosync = 1;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
if (bootverbose) {
ahd_print_devinfo(ahd, devinfo);
printf("Ensuring async\n");
}
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/* Target initiated PPR is not allowed in the SCSI spec */
if (devinfo->role == ROLE_TARGET)
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
doppr = 0;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*
* Both the PPR message and SDTR message require the
* goal syncrate to be limited to what the target device
* is capable of handling (based on whether an LVD->SE
* expander is on the bus), so combine these two cases.
* Regardless, guarantee that if we are using WDTR and SDTR
* messages that WDTR comes first.
*/
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
if (doppr || (dosync && !dowide)) {
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
offset = tinfo->goal.offset;
ahd_validate_offset(ahd, tinfo, period, &offset,
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
doppr ? tinfo->goal.width
: tinfo->curr.width,
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
devinfo->role);
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
if (doppr) {
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_construct_ppr(ahd, devinfo, period, offset,
tinfo->goal.width, ppr_options);
} else {
ahd_construct_sdtr(ahd, devinfo, period, offset);
}
} else {
ahd_construct_wdtr(ahd, devinfo, tinfo->goal.width);
}
}
/*
* Build a synchronous negotiation message in our message
* buffer based on the input parameters.
*/
static void
ahd_construct_sdtr(struct ahd_softc *ahd, struct ahd_devinfo *devinfo,
u_int period, u_int offset)
{
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
if (offset == 0)
period = AHD_ASYNC_XFER_PERIOD;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd->msgout_buf[ahd->msgout_index++] = MSG_EXTENDED;
ahd->msgout_buf[ahd->msgout_index++] = MSG_EXT_SDTR_LEN;
ahd->msgout_buf[ahd->msgout_index++] = MSG_EXT_SDTR;
ahd->msgout_buf[ahd->msgout_index++] = period;
ahd->msgout_buf[ahd->msgout_index++] = offset;
ahd->msgout_len += 5;
if (bootverbose) {
printf("(%s:%c:%d:%d): Sending SDTR period %x, offset %x\n",
ahd_name(ahd), devinfo->channel, devinfo->target,
devinfo->lun, period, offset);
}
}
/*
* Build a wide negotiateion message in our message
* buffer based on the input parameters.
*/
static void
ahd_construct_wdtr(struct ahd_softc *ahd, struct ahd_devinfo *devinfo,
u_int bus_width)
{
ahd->msgout_buf[ahd->msgout_index++] = MSG_EXTENDED;
ahd->msgout_buf[ahd->msgout_index++] = MSG_EXT_WDTR_LEN;
ahd->msgout_buf[ahd->msgout_index++] = MSG_EXT_WDTR;
ahd->msgout_buf[ahd->msgout_index++] = bus_width;
ahd->msgout_len += 4;
if (bootverbose) {
printf("(%s:%c:%d:%d): Sending WDTR %x\n",
ahd_name(ahd), devinfo->channel, devinfo->target,
devinfo->lun, bus_width);
}
}
/*
* Build a parallel protocol request message in our message
* buffer based on the input parameters.
*/
static void
ahd_construct_ppr(struct ahd_softc *ahd, struct ahd_devinfo *devinfo,
u_int period, u_int offset, u_int bus_width,
u_int ppr_options)
{
/*
* Always request precompensation from
* the other target if we are running
* at paced syncrates.
*/
if (period <= AHD_SYNCRATE_PACED)
ppr_options |= MSG_EXT_PPR_PCOMP_EN;
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
if (offset == 0)
period = AHD_ASYNC_XFER_PERIOD;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd->msgout_buf[ahd->msgout_index++] = MSG_EXTENDED;
ahd->msgout_buf[ahd->msgout_index++] = MSG_EXT_PPR_LEN;
ahd->msgout_buf[ahd->msgout_index++] = MSG_EXT_PPR;
ahd->msgout_buf[ahd->msgout_index++] = period;
ahd->msgout_buf[ahd->msgout_index++] = 0;
ahd->msgout_buf[ahd->msgout_index++] = offset;
ahd->msgout_buf[ahd->msgout_index++] = bus_width;
ahd->msgout_buf[ahd->msgout_index++] = ppr_options;
ahd->msgout_len += 8;
if (bootverbose) {
printf("(%s:%c:%d:%d): Sending PPR bus_width %x, period %x, "
"offset %x, ppr_options %x\n", ahd_name(ahd),
devinfo->channel, devinfo->target, devinfo->lun,
bus_width, period, offset, ppr_options);
}
}
/*
* Clear any active message state.
*/
static void
ahd_clear_msg_state(struct ahd_softc *ahd)
{
ahd_mode_state saved_modes;
saved_modes = ahd_save_modes(ahd);
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
ahd->send_msg_perror = 0;
ahd->msg_flags = MSG_FLAG_NONE;
ahd->msgout_len = 0;
ahd->msgin_index = 0;
ahd->msg_type = MSG_TYPE_NONE;
if ((ahd_inb(ahd, SCSISIGO) & ATNO) != 0) {
/*
* The target didn't care to respond to our
* message request, so clear ATN.
*/
ahd_outb(ahd, CLRSINT1, CLRATNO);
}
ahd_outb(ahd, MSG_OUT, MSG_NOOP);
ahd_outb(ahd, SEQ_FLAGS2,
ahd_inb(ahd, SEQ_FLAGS2) & ~TARGET_MSG_PENDING);
ahd_restore_modes(ahd, saved_modes);
}
/*
* Manual message loop handler.
*/
static void
ahd_handle_message_phase(struct ahd_softc *ahd)
{
struct ahd_devinfo devinfo;
u_int bus_phase;
int end_session;
ahd_fetch_devinfo(ahd, &devinfo);
end_session = FALSE;
bus_phase = ahd_inb(ahd, LASTPHASE);
if ((ahd_inb(ahd, LQISTAT2) & LQIPHASE_OUTPKT) != 0) {
printf("LQIRETRY for LQIPHASE_OUTPKT\n");
ahd_outb(ahd, LQCTL2, LQIRETRY);
}
reswitch:
switch (ahd->msg_type) {
case MSG_TYPE_INITIATOR_MSGOUT:
{
int lastbyte;
int phasemis;
int msgdone;
if (ahd->msgout_len == 0 && ahd->send_msg_perror == 0)
panic("HOST_MSG_LOOP interrupt with no active message");
#ifdef AHD_DEBUG
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
if ((ahd_debug & AHD_SHOW_MESSAGES) != 0) {
ahd_print_devinfo(ahd, &devinfo);
printf("INITIATOR_MSG_OUT");
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
#endif
phasemis = bus_phase != P_MESGOUT;
if (phasemis) {
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_MESSAGES) != 0) {
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
printf(" PHASEMIS %s\n",
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_lookup_phase_entry(bus_phase)
->phasemsg);
}
#endif
if (bus_phase == P_MESGIN) {
/*
* Change gears and see if
* this messages is of interest to
* us or should be passed back to
* the sequencer.
*/
ahd_outb(ahd, CLRSINT1, CLRATNO);
ahd->send_msg_perror = 0;
ahd->msg_type = MSG_TYPE_INITIATOR_MSGIN;
ahd->msgin_index = 0;
goto reswitch;
}
end_session = TRUE;
break;
}
if (ahd->send_msg_perror) {
ahd_outb(ahd, CLRSINT1, CLRATNO);
ahd_outb(ahd, CLRSINT1, CLRREQINIT);
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_MESSAGES) != 0)
printf(" byte 0x%x\n", ahd->send_msg_perror);
#endif
/*
* If we are notifying the target of a CRC error
* during packetized operations, the target is
* within its rights to acknowledge our message
* with a busfree.
*/
if ((ahd->msg_flags & MSG_FLAG_PACKETIZED) != 0
&& ahd->send_msg_perror == MSG_INITIATOR_DET_ERR)
ahd->msg_flags |= MSG_FLAG_EXPECT_IDE_BUSFREE;
ahd_outb(ahd, RETURN_2, ahd->send_msg_perror);
ahd_outb(ahd, RETURN_1, CONT_MSG_LOOP_WRITE);
break;
}
msgdone = ahd->msgout_index == ahd->msgout_len;
if (msgdone) {
/*
* The target has requested a retry.
* Re-assert ATN, reset our message index to
* 0, and try again.
*/
ahd->msgout_index = 0;
ahd_assert_atn(ahd);
}
lastbyte = ahd->msgout_index == (ahd->msgout_len - 1);
if (lastbyte) {
/* Last byte is signified by dropping ATN */
ahd_outb(ahd, CLRSINT1, CLRATNO);
}
/*
* Clear our interrupt status and present
* the next byte on the bus.
*/
ahd_outb(ahd, CLRSINT1, CLRREQINIT);
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_MESSAGES) != 0)
printf(" byte 0x%x\n",
ahd->msgout_buf[ahd->msgout_index]);
#endif
ahd_outb(ahd, RETURN_2, ahd->msgout_buf[ahd->msgout_index++]);
ahd_outb(ahd, RETURN_1, CONT_MSG_LOOP_WRITE);
break;
}
case MSG_TYPE_INITIATOR_MSGIN:
{
int phasemis;
int message_done;
#ifdef AHD_DEBUG
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
if ((ahd_debug & AHD_SHOW_MESSAGES) != 0) {
ahd_print_devinfo(ahd, &devinfo);
printf("INITIATOR_MSG_IN");
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
#endif
phasemis = bus_phase != P_MESGIN;
if (phasemis) {
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_MESSAGES) != 0) {
printf(" PHASEMIS %s\n",
ahd_lookup_phase_entry(bus_phase)
->phasemsg);
}
#endif
ahd->msgin_index = 0;
if (bus_phase == P_MESGOUT
&& (ahd->send_msg_perror != 0
|| (ahd->msgout_len != 0
&& ahd->msgout_index == 0))) {
ahd->msg_type = MSG_TYPE_INITIATOR_MSGOUT;
goto reswitch;
}
end_session = TRUE;
break;
}
/* Pull the byte in without acking it */
ahd->msgin_buf[ahd->msgin_index] = ahd_inb(ahd, SCSIBUS);
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_MESSAGES) != 0)
printf(" byte 0x%x\n",
ahd->msgin_buf[ahd->msgin_index]);
#endif
message_done = ahd_parse_msg(ahd, &devinfo);
if (message_done) {
/*
* Clear our incoming message buffer in case there
* is another message following this one.
*/
ahd->msgin_index = 0;
/*
* If this message illicited a response,
* assert ATN so the target takes us to the
* message out phase.
*/
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
if (ahd->msgout_len != 0) {
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_MESSAGES) != 0) {
ahd_print_devinfo(ahd, &devinfo);
printf("Asserting ATN for response\n");
}
#endif
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_assert_atn(ahd);
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
} else
ahd->msgin_index++;
if (message_done == MSGLOOP_TERMINATED) {
end_session = TRUE;
} else {
/* Ack the byte */
ahd_outb(ahd, CLRSINT1, CLRREQINIT);
ahd_outb(ahd, RETURN_1, CONT_MSG_LOOP_READ);
}
break;
}
case MSG_TYPE_TARGET_MSGIN:
{
int msgdone;
int msgout_request;
/*
* By default, the message loop will continue.
*/
ahd_outb(ahd, RETURN_1, CONT_MSG_LOOP_TARG);
if (ahd->msgout_len == 0)
panic("Target MSGIN with no active message");
/*
* If we interrupted a mesgout session, the initiator
* will not know this until our first REQ. So, we
* only honor mesgout requests after we've sent our
* first byte.
*/
if ((ahd_inb(ahd, SCSISIGI) & ATNI) != 0
&& ahd->msgout_index > 0)
msgout_request = TRUE;
else
msgout_request = FALSE;
if (msgout_request) {
/*
* Change gears and see if
* this messages is of interest to
* us or should be passed back to
* the sequencer.
*/
ahd->msg_type = MSG_TYPE_TARGET_MSGOUT;
ahd_outb(ahd, SCSISIGO, P_MESGOUT | BSYO);
ahd->msgin_index = 0;
/* Dummy read to REQ for first byte */
ahd_inb(ahd, SCSIDAT);
ahd_outb(ahd, SXFRCTL0,
ahd_inb(ahd, SXFRCTL0) | SPIOEN);
break;
}
msgdone = ahd->msgout_index == ahd->msgout_len;
if (msgdone) {
ahd_outb(ahd, SXFRCTL0,
ahd_inb(ahd, SXFRCTL0) & ~SPIOEN);
end_session = TRUE;
break;
}
/*
* Present the next byte on the bus.
*/
ahd_outb(ahd, SXFRCTL0, ahd_inb(ahd, SXFRCTL0) | SPIOEN);
ahd_outb(ahd, SCSIDAT, ahd->msgout_buf[ahd->msgout_index++]);
break;
}
case MSG_TYPE_TARGET_MSGOUT:
{
int lastbyte;
int msgdone;
/*
* By default, the message loop will continue.
*/
ahd_outb(ahd, RETURN_1, CONT_MSG_LOOP_TARG);
/*
* The initiator signals that this is
* the last byte by dropping ATN.
*/
lastbyte = (ahd_inb(ahd, SCSISIGI) & ATNI) == 0;
/*
* Read the latched byte, but turn off SPIOEN first
* so that we don't inadvertently cause a REQ for the
* next byte.
*/
ahd_outb(ahd, SXFRCTL0, ahd_inb(ahd, SXFRCTL0) & ~SPIOEN);
ahd->msgin_buf[ahd->msgin_index] = ahd_inb(ahd, SCSIDAT);
msgdone = ahd_parse_msg(ahd, &devinfo);
if (msgdone == MSGLOOP_TERMINATED) {
/*
* The message is *really* done in that it caused
* us to go to bus free. The sequencer has already
* been reset at this point, so pull the ejection
* handle.
*/
return;
}
ahd->msgin_index++;
/*
* XXX Read spec about initiator dropping ATN too soon
* and use msgdone to detect it.
*/
if (msgdone == MSGLOOP_MSGCOMPLETE) {
ahd->msgin_index = 0;
/*
* If this message illicited a response, transition
* to the Message in phase and send it.
*/
if (ahd->msgout_len != 0) {
ahd_outb(ahd, SCSISIGO, P_MESGIN | BSYO);
ahd_outb(ahd, SXFRCTL0,
ahd_inb(ahd, SXFRCTL0) | SPIOEN);
ahd->msg_type = MSG_TYPE_TARGET_MSGIN;
ahd->msgin_index = 0;
break;
}
}
if (lastbyte)
end_session = TRUE;
else {
/* Ask for the next byte. */
ahd_outb(ahd, SXFRCTL0,
ahd_inb(ahd, SXFRCTL0) | SPIOEN);
}
break;
}
default:
panic("Unknown REQINIT message type");
}
if (end_session) {
if ((ahd->msg_flags & MSG_FLAG_PACKETIZED) != 0) {
printf("%s: Returning to Idle Loop\n",
ahd_name(ahd));
ahd_clear_msg_state(ahd);
Correct a typo in a comment. Add a comment in ahd_clear_critical_sections() about our need to leave ENBUSFREE set in SIMODE1 while single stepping. Re-arrange some delay loops so that we always perform a read after any register write and before the delay. This should make the delay loop more accurate. When completing message processing for a packetized commention, return the controller to a state where invalid non-packetized phases will still cause protocol violations. These are the same operations as those performed in the clear_target_state routine in the firmware. Now that we have a chip with working ABORTPENDING support (the 7901B), comment out the automatic use of this feature until we can adequately test it. The previous checkin updated the bug mask for the 7901B so this code was exercised. When resetting the bus, perform an ahd_flush_device_writes() call so that our reset assertion delay is acurately timed from when the reset bit is written to the controller.
2003-06-28 04:42:11 +00:00
/*
* Perform the equivalent of a clear_target_state.
*/
ahd_outb(ahd, LASTPHASE, P_BUSFREE);
ahd_outb(ahd, SEQ_FLAGS, NOT_IDENTIFIED|NO_CDB_SENT);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_outb(ahd, SEQCTL0, FASTMODE|SEQRESET);
} else {
ahd_clear_msg_state(ahd);
ahd_outb(ahd, RETURN_1, EXIT_MSG_LOOP);
}
}
}
/*
* See if we sent a particular extended message to the target.
* If "full" is true, return true only if the target saw the full
* message. If "full" is false, return true if the target saw at
* least the first byte of the message.
*/
static int
ahd_sent_msg(struct ahd_softc *ahd, ahd_msgtype type, u_int msgval, int full)
{
int found;
u_int index;
found = FALSE;
index = 0;
while (index < ahd->msgout_len) {
if (ahd->msgout_buf[index] == MSG_EXTENDED) {
u_int end_index;
end_index = index + 1 + ahd->msgout_buf[index + 1];
if (ahd->msgout_buf[index+2] == msgval
&& type == AHDMSG_EXT) {
if (full) {
if (ahd->msgout_index > end_index)
found = TRUE;
} else if (ahd->msgout_index > index)
found = TRUE;
}
index = end_index;
} else if (ahd->msgout_buf[index] >= MSG_SIMPLE_TASK
&& ahd->msgout_buf[index] <= MSG_IGN_WIDE_RESIDUE) {
/* Skip tag type and tag id or residue param*/
index += 2;
} else {
/* Single byte message */
if (type == AHDMSG_1B
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
&& ahd->msgout_index > index
&& (ahd->msgout_buf[index] == msgval
|| ((ahd->msgout_buf[index] & MSG_IDENTIFYFLAG) != 0
&& msgval == MSG_IDENTIFYFLAG)))
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
found = TRUE;
index++;
}
if (found)
break;
}
return (found);
}
/*
* Wait for a complete incoming message, parse it, and respond accordingly.
*/
static int
ahd_parse_msg(struct ahd_softc *ahd, struct ahd_devinfo *devinfo)
{
struct ahd_initiator_tinfo *tinfo;
struct ahd_tmode_tstate *tstate;
int reject;
int done;
int response;
done = MSGLOOP_IN_PROG;
response = FALSE;
reject = FALSE;
tinfo = ahd_fetch_transinfo(ahd, devinfo->channel, devinfo->our_scsiid,
devinfo->target, &tstate);
/*
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
* Parse as much of the message as is available,
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
* rejecting it if we don't support it. When
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
* the entire message is available and has been
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
* handled, return MSGLOOP_MSGCOMPLETE, indicating
* that we have parsed an entire message.
*
* In the case of extended messages, we accept the length
* byte outright and perform more checking once we know the
* extended message type.
*/
switch (ahd->msgin_buf[0]) {
case MSG_DISCONNECT:
case MSG_SAVEDATAPOINTER:
case MSG_CMDCOMPLETE:
case MSG_RESTOREPOINTERS:
case MSG_IGN_WIDE_RESIDUE:
/*
* End our message loop as these are messages
* the sequencer handles on its own.
*/
done = MSGLOOP_TERMINATED;
break;
case MSG_MESSAGE_REJECT:
response = ahd_handle_msg_reject(ahd, devinfo);
/* FALLTHROUGH */
case MSG_NOOP:
done = MSGLOOP_MSGCOMPLETE;
break;
case MSG_EXTENDED:
{
/* Wait for enough of the message to begin validation */
if (ahd->msgin_index < 2)
break;
switch (ahd->msgin_buf[2]) {
case MSG_EXT_SDTR:
{
u_int period;
u_int ppr_options;
u_int offset;
u_int saved_offset;
if (ahd->msgin_buf[1] != MSG_EXT_SDTR_LEN) {
reject = TRUE;
break;
}
/*
* Wait until we have both args before validating
* and acting on this message.
*
* Add one to MSG_EXT_SDTR_LEN to account for
* the extended message preamble.
*/
if (ahd->msgin_index < (MSG_EXT_SDTR_LEN + 1))
break;
period = ahd->msgin_buf[3];
ppr_options = 0;
saved_offset = offset = ahd->msgin_buf[4];
ahd_devlimited_syncrate(ahd, tinfo, &period,
&ppr_options, devinfo->role);
ahd_validate_offset(ahd, tinfo, period, &offset,
tinfo->curr.width, devinfo->role);
if (bootverbose) {
printf("(%s:%c:%d:%d): Received "
"SDTR period %x, offset %x\n\t"
"Filtered to period %x, offset %x\n",
ahd_name(ahd), devinfo->channel,
devinfo->target, devinfo->lun,
ahd->msgin_buf[3], saved_offset,
period, offset);
}
ahd_set_syncrate(ahd, devinfo, period,
offset, ppr_options,
AHD_TRANS_ACTIVE|AHD_TRANS_GOAL,
/*paused*/TRUE);
/*
* See if we initiated Sync Negotiation
* and didn't have to fall down to async
* transfers.
*/
if (ahd_sent_msg(ahd, AHDMSG_EXT, MSG_EXT_SDTR, TRUE)) {
/* We started it */
if (saved_offset != offset) {
/* Went too low - force async */
reject = TRUE;
}
} else {
/*
* Send our own SDTR in reply
*/
if (bootverbose
&& devinfo->role == ROLE_INITIATOR) {
printf("(%s:%c:%d:%d): Target "
"Initiated SDTR\n",
ahd_name(ahd), devinfo->channel,
devinfo->target, devinfo->lun);
}
ahd->msgout_index = 0;
ahd->msgout_len = 0;
ahd_construct_sdtr(ahd, devinfo,
period, offset);
ahd->msgout_index = 0;
response = TRUE;
}
done = MSGLOOP_MSGCOMPLETE;
break;
}
case MSG_EXT_WDTR:
{
u_int bus_width;
u_int saved_width;
u_int sending_reply;
sending_reply = FALSE;
if (ahd->msgin_buf[1] != MSG_EXT_WDTR_LEN) {
reject = TRUE;
break;
}
/*
* Wait until we have our arg before validating
* and acting on this message.
*
* Add one to MSG_EXT_WDTR_LEN to account for
* the extended message preamble.
*/
if (ahd->msgin_index < (MSG_EXT_WDTR_LEN + 1))
break;
bus_width = ahd->msgin_buf[3];
saved_width = bus_width;
ahd_validate_width(ahd, tinfo, &bus_width,
devinfo->role);
if (bootverbose) {
printf("(%s:%c:%d:%d): Received WDTR "
"%x filtered to %x\n",
ahd_name(ahd), devinfo->channel,
devinfo->target, devinfo->lun,
saved_width, bus_width);
}
if (ahd_sent_msg(ahd, AHDMSG_EXT, MSG_EXT_WDTR, TRUE)) {
/*
* Don't send a WDTR back to the
* target, since we asked first.
* If the width went higher than our
* request, reject it.
*/
if (saved_width > bus_width) {
reject = TRUE;
printf("(%s:%c:%d:%d): requested %dBit "
"transfers. Rejecting...\n",
ahd_name(ahd), devinfo->channel,
devinfo->target, devinfo->lun,
8 * (0x01 << bus_width));
bus_width = 0;
}
} else {
/*
* Send our own WDTR in reply
*/
if (bootverbose
&& devinfo->role == ROLE_INITIATOR) {
printf("(%s:%c:%d:%d): Target "
"Initiated WDTR\n",
ahd_name(ahd), devinfo->channel,
devinfo->target, devinfo->lun);
}
ahd->msgout_index = 0;
ahd->msgout_len = 0;
ahd_construct_wdtr(ahd, devinfo, bus_width);
ahd->msgout_index = 0;
response = TRUE;
sending_reply = TRUE;
}
Work around SCSI spec violation by the Quantum Atlas 10K. This drive delays going async after receiving a WDTR message. We now send an SDTR message after a WDTR even if our goal is to go async. This should work even for confused devices. If we get an unexpected busfree when attempting a WDTR or SDTR, only set the goal negotiation parameters we were trying to negotiate to off. This means that should a WDTR message fail, we will still try an SDTR if our goal is non-async. Fix a few more places where we were looking at goal.period instead of goal.offset for determining if we should be negotiating sync. This should not have any impact on our behavior, but the offset is more definitive and should be used.
2003-06-06 23:51:13 +00:00
/*
* After a wide message, we are async, but
* some devices don't seem to honor this portion
* of the spec. Force a renegotiation of the
* sync component of our transfer agreement even
* if our goal is async. By updating our width
* after forcing the negotiation, we avoid
* renegotiating for width.
*/
ahd_update_neg_request(ahd, devinfo, tstate,
tinfo, AHD_NEG_ALWAYS);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_set_width(ahd, devinfo, bus_width,
AHD_TRANS_ACTIVE|AHD_TRANS_GOAL,
/*paused*/TRUE);
if (sending_reply == FALSE && reject == FALSE) {
Work around SCSI spec violation by the Quantum Atlas 10K. This drive delays going async after receiving a WDTR message. We now send an SDTR message after a WDTR even if our goal is to go async. This should work even for confused devices. If we get an unexpected busfree when attempting a WDTR or SDTR, only set the goal negotiation parameters we were trying to negotiate to off. This means that should a WDTR message fail, we will still try an SDTR if our goal is non-async. Fix a few more places where we were looking at goal.period instead of goal.offset for determining if we should be negotiating sync. This should not have any impact on our behavior, but the offset is more definitive and should be used.
2003-06-06 23:51:13 +00:00
/*
* We will always have an SDTR to send.
*/
ahd->msgout_index = 0;
ahd->msgout_len = 0;
ahd_build_transfer_msg(ahd, devinfo);
ahd->msgout_index = 0;
response = TRUE;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
done = MSGLOOP_MSGCOMPLETE;
break;
}
case MSG_EXT_PPR:
{
u_int period;
u_int offset;
u_int bus_width;
u_int ppr_options;
u_int saved_width;
u_int saved_offset;
u_int saved_ppr_options;
if (ahd->msgin_buf[1] != MSG_EXT_PPR_LEN) {
reject = TRUE;
break;
}
/*
* Wait until we have all args before validating
* and acting on this message.
*
* Add one to MSG_EXT_PPR_LEN to account for
* the extended message preamble.
*/
if (ahd->msgin_index < (MSG_EXT_PPR_LEN + 1))
break;
period = ahd->msgin_buf[3];
offset = ahd->msgin_buf[5];
bus_width = ahd->msgin_buf[6];
saved_width = bus_width;
ppr_options = ahd->msgin_buf[7];
/*
* According to the spec, a DT only
* period factor with no DT option
* set implies async.
*/
if ((ppr_options & MSG_EXT_PPR_DT_REQ) == 0
&& period <= 9)
offset = 0;
saved_ppr_options = ppr_options;
saved_offset = offset;
/*
* Transfer options are only available if we
* are negotiating wide.
*/
if (bus_width == 0)
ppr_options &= MSG_EXT_PPR_QAS_REQ;
ahd_validate_width(ahd, tinfo, &bus_width,
devinfo->role);
ahd_devlimited_syncrate(ahd, tinfo, &period,
&ppr_options, devinfo->role);
ahd_validate_offset(ahd, tinfo, period, &offset,
bus_width, devinfo->role);
if (ahd_sent_msg(ahd, AHDMSG_EXT, MSG_EXT_PPR, TRUE)) {
/*
* If we are unable to do any of the
* requested options (we went too low),
* then we'll have to reject the message.
*/
if (saved_width > bus_width
|| saved_offset != offset
|| saved_ppr_options != ppr_options) {
reject = TRUE;
period = 0;
offset = 0;
bus_width = 0;
ppr_options = 0;
}
} else {
if (devinfo->role != ROLE_TARGET)
printf("(%s:%c:%d:%d): Target "
"Initiated PPR\n",
ahd_name(ahd), devinfo->channel,
devinfo->target, devinfo->lun);
else
printf("(%s:%c:%d:%d): Initiator "
"Initiated PPR\n",
ahd_name(ahd), devinfo->channel,
devinfo->target, devinfo->lun);
ahd->msgout_index = 0;
ahd->msgout_len = 0;
ahd_construct_ppr(ahd, devinfo, period, offset,
bus_width, ppr_options);
ahd->msgout_index = 0;
response = TRUE;
}
if (bootverbose) {
printf("(%s:%c:%d:%d): Received PPR width %x, "
"period %x, offset %x,options %x\n"
"\tFiltered to width %x, period %x, "
"offset %x, options %x\n",
ahd_name(ahd), devinfo->channel,
devinfo->target, devinfo->lun,
saved_width, ahd->msgin_buf[3],
saved_offset, saved_ppr_options,
bus_width, period, offset, ppr_options);
}
ahd_set_width(ahd, devinfo, bus_width,
AHD_TRANS_ACTIVE|AHD_TRANS_GOAL,
/*paused*/TRUE);
ahd_set_syncrate(ahd, devinfo, period,
offset, ppr_options,
AHD_TRANS_ACTIVE|AHD_TRANS_GOAL,
/*paused*/TRUE);
done = MSGLOOP_MSGCOMPLETE;
break;
}
default:
/* Unknown extended message. Reject it. */
reject = TRUE;
break;
}
break;
}
#ifdef AHD_TARGET_MODE
case MSG_BUS_DEV_RESET:
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
ahd_handle_devreset(ahd, devinfo, CAM_LUN_WILDCARD,
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
CAM_BDR_SENT,
"Bus Device Reset Received",
/*verbose_level*/0);
ahd_restart(ahd);
done = MSGLOOP_TERMINATED;
break;
case MSG_ABORT_TAG:
case MSG_ABORT:
case MSG_CLEAR_QUEUE:
{
int tag;
/* Target mode messages */
if (devinfo->role != ROLE_TARGET) {
reject = TRUE;
break;
}
tag = SCB_LIST_NULL;
if (ahd->msgin_buf[0] == MSG_ABORT_TAG)
tag = ahd_inb(ahd, INITIATOR_TAG);
ahd_abort_scbs(ahd, devinfo->target, devinfo->channel,
devinfo->lun, tag, ROLE_TARGET,
CAM_REQ_ABORTED);
tstate = ahd->enabled_targets[devinfo->our_scsiid];
if (tstate != NULL) {
struct ahd_tmode_lstate* lstate;
lstate = tstate->enabled_luns[devinfo->lun];
if (lstate != NULL) {
ahd_queue_lstate_event(ahd, lstate,
devinfo->our_scsiid,
ahd->msgin_buf[0],
/*arg*/tag);
ahd_send_lstate_events(ahd, lstate);
}
}
ahd_restart(ahd);
done = MSGLOOP_TERMINATED;
break;
}
#endif
case MSG_QAS_REQUEST:
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_MESSAGES) != 0)
printf("%s: QAS request. SCSISIGI == 0x%x\n",
ahd_name(ahd), ahd_inb(ahd, SCSISIGI));
#endif
ahd->msg_flags |= MSG_FLAG_EXPECT_QASREJ_BUSFREE;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/* FALLTHROUGH */
case MSG_TERM_IO_PROC:
default:
reject = TRUE;
break;
}
if (reject) {
/*
* Setup to reject the message.
*/
ahd->msgout_index = 0;
ahd->msgout_len = 1;
ahd->msgout_buf[0] = MSG_MESSAGE_REJECT;
done = MSGLOOP_MSGCOMPLETE;
response = TRUE;
}
if (done != MSGLOOP_IN_PROG && !response)
/* Clear the outgoing message buffer */
ahd->msgout_len = 0;
return (done);
}
/*
* Process a message reject message.
*/
static int
ahd_handle_msg_reject(struct ahd_softc *ahd, struct ahd_devinfo *devinfo)
{
/*
* What we care about here is if we had an
* outstanding SDTR or WDTR message for this
* target. If we did, this is a signal that
* the target is refusing negotiation.
*/
struct scb *scb;
struct ahd_initiator_tinfo *tinfo;
struct ahd_tmode_tstate *tstate;
u_int scb_index;
u_int last_msg;
int response = 0;
scb_index = ahd_get_scbptr(ahd);
scb = ahd_lookup_scb(ahd, scb_index);
tinfo = ahd_fetch_transinfo(ahd, devinfo->channel,
devinfo->our_scsiid,
devinfo->target, &tstate);
/* Might be necessary */
last_msg = ahd_inb(ahd, LAST_MSG);
if (ahd_sent_msg(ahd, AHDMSG_EXT, MSG_EXT_PPR, /*full*/FALSE)) {
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
if (ahd_sent_msg(ahd, AHDMSG_EXT, MSG_EXT_PPR, /*full*/TRUE)
&& tinfo->goal.period <= AHD_SYNCRATE_PACED) {
/*
* Target may not like our SPI-4 PPR Options.
* Attempt to negotiate 80MHz which will turn
* off these options.
*/
if (bootverbose) {
printf("(%s:%c:%d:%d): PPR Rejected. "
"Trying simple U160 PPR\n",
ahd_name(ahd), devinfo->channel,
devinfo->target, devinfo->lun);
}
tinfo->goal.period = AHD_SYNCRATE_DT;
tinfo->goal.ppr_options &= MSG_EXT_PPR_IU_REQ
| MSG_EXT_PPR_QAS_REQ
| MSG_EXT_PPR_DT_REQ;
} else {
/*
* Target does not support the PPR message.
* Attempt to negotiate SPI-2 style.
*/
if (bootverbose) {
printf("(%s:%c:%d:%d): PPR Rejected. "
"Trying WDTR/SDTR\n",
ahd_name(ahd), devinfo->channel,
devinfo->target, devinfo->lun);
}
tinfo->goal.ppr_options = 0;
tinfo->curr.transport_version = 2;
tinfo->goal.transport_version = 2;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
ahd->msgout_index = 0;
ahd->msgout_len = 0;
ahd_build_transfer_msg(ahd, devinfo);
ahd->msgout_index = 0;
response = 1;
} else if (ahd_sent_msg(ahd, AHDMSG_EXT, MSG_EXT_WDTR, /*full*/FALSE)) {
/* note 8bit xfers */
printf("(%s:%c:%d:%d): refuses WIDE negotiation. Using "
"8bit transfers\n", ahd_name(ahd),
devinfo->channel, devinfo->target, devinfo->lun);
ahd_set_width(ahd, devinfo, MSG_EXT_WDTR_BUS_8_BIT,
AHD_TRANS_ACTIVE|AHD_TRANS_GOAL,
/*paused*/TRUE);
/*
* No need to clear the sync rate. If the target
* did not accept the command, our syncrate is
* unaffected. If the target started the negotiation,
* but rejected our response, we already cleared the
* sync rate before sending our WDTR.
*/
Fix a missed goal.period -> goal.offset change. In this case, the bug resulted in comparing a period against an offset.
2003-01-20 23:51:18 +00:00
if (tinfo->goal.offset != tinfo->curr.offset) {
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/* Start the sync negotiation */
ahd->msgout_index = 0;
ahd->msgout_len = 0;
ahd_build_transfer_msg(ahd, devinfo);
ahd->msgout_index = 0;
response = 1;
}
} else if (ahd_sent_msg(ahd, AHDMSG_EXT, MSG_EXT_SDTR, /*full*/FALSE)) {
/* note asynch xfers and clear flag */
ahd_set_syncrate(ahd, devinfo, /*period*/0,
/*offset*/0, /*ppr_options*/0,
AHD_TRANS_ACTIVE|AHD_TRANS_GOAL,
/*paused*/TRUE);
printf("(%s:%c:%d:%d): refuses synchronous negotiation. "
"Using asynchronous transfers\n",
ahd_name(ahd), devinfo->channel,
devinfo->target, devinfo->lun);
} else if ((scb->hscb->control & MSG_SIMPLE_TASK) != 0) {
int tag_type;
int mask;
tag_type = (scb->hscb->control & MSG_SIMPLE_TASK);
if (tag_type == MSG_SIMPLE_TASK) {
printf("(%s:%c:%d:%d): refuses tagged commands. "
"Performing non-tagged I/O\n", ahd_name(ahd),
devinfo->channel, devinfo->target, devinfo->lun);
ahd_set_tags(ahd, devinfo, AHD_QUEUE_NONE);
mask = ~0x23;
} else {
printf("(%s:%c:%d:%d): refuses %s tagged commands. "
"Performing simple queue tagged I/O only\n",
ahd_name(ahd), devinfo->channel, devinfo->target,
devinfo->lun, tag_type == MSG_ORDERED_TASK
? "ordered" : "head of queue");
ahd_set_tags(ahd, devinfo, AHD_QUEUE_BASIC);
mask = ~0x03;
}
/*
* Resend the identify for this CCB as the target
* may believe that the selection is invalid otherwise.
*/
ahd_outb(ahd, SCB_CONTROL,
ahd_inb_scbram(ahd, SCB_CONTROL) & mask);
scb->hscb->control &= mask;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_set_transaction_tag(scb, /*enabled*/FALSE,
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*type*/MSG_SIMPLE_TASK);
ahd_outb(ahd, MSG_OUT, MSG_IDENTIFYFLAG);
ahd_assert_atn(ahd);
ahd_busy_tcl(ahd, BUILD_TCL(scb->hscb->scsiid, devinfo->lun),
SCB_GET_TAG(scb));
/*
* Requeue all tagged commands for this target
* currently in our posession so they can be
* converted to untagged commands.
*/
ahd_search_qinfifo(ahd, SCB_GET_TARGET(ahd, scb),
SCB_GET_CHANNEL(ahd, scb),
SCB_GET_LUN(scb), /*tag*/SCB_LIST_NULL,
ROLE_INITIATOR, CAM_REQUEUE_REQ,
SEARCH_COMPLETE);
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
} else if (ahd_sent_msg(ahd, AHDMSG_1B, MSG_IDENTIFYFLAG, TRUE)) {
/*
* Most likely the device believes that we had
* previously negotiated packetized.
*/
ahd->msg_flags |= MSG_FLAG_EXPECT_PPR_BUSFREE
| MSG_FLAG_IU_REQ_CHANGED;
ahd_force_renegotiation(ahd, devinfo);
ahd->msgout_index = 0;
ahd->msgout_len = 0;
ahd_build_transfer_msg(ahd, devinfo);
ahd->msgout_index = 0;
response = 1;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
} else {
/*
* Otherwise, we ignore it.
*/
printf("%s:%c:%d: Message reject for %x -- ignored\n",
ahd_name(ahd), devinfo->channel, devinfo->target,
last_msg);
}
return (response);
}
/*
* Process an ingnore wide residue message.
*/
static void
ahd_handle_ign_wide_residue(struct ahd_softc *ahd, struct ahd_devinfo *devinfo)
{
u_int scb_index;
struct scb *scb;
scb_index = ahd_get_scbptr(ahd);
scb = ahd_lookup_scb(ahd, scb_index);
/*
* XXX Actually check data direction in the sequencer?
* Perhaps add datadir to some spare bits in the hscb?
*/
if ((ahd_inb(ahd, SEQ_FLAGS) & DPHASE) == 0
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
|| aic_get_transfer_dir(scb) != CAM_DIR_IN) {
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*
* Ignore the message if we haven't
* seen an appropriate data phase yet.
*/
} else {
/*
* If the residual occurred on the last
* transfer and the transfer request was
* expected to end on an odd count, do
* nothing. Otherwise, subtract a byte
* and update the residual count accordingly.
*/
uint32_t sgptr;
sgptr = ahd_inb_scbram(ahd, SCB_RESIDUAL_SGPTR);
if ((sgptr & SG_LIST_NULL) != 0
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
&& (ahd_inb_scbram(ahd, SCB_TASK_ATTRIBUTE)
& SCB_XFERLEN_ODD) != 0) {
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*
* If the residual occurred on the last
* transfer and the transfer request was
* expected to end on an odd count, do
* nothing.
*/
} else {
uint32_t data_cnt;
uint64_t data_addr;
uint32_t sglen;
/* Pull in the rest of the sgptr */
Correct/Simplify ignore wide residue message handling aic79xx.c: In ahd_handle_ign_wide_residue(): o Use SCB_XFERLEN_ODD SCB field to determine transfer "oddness" rather than the DATA_COUNT_ODD logic. SCB_XFERLEN_ODD is toggled on every ignore wide residue message so that multiple ignore wide residue messages for the same transaction are properly supported. o If the sg list has been exausted, the sequencer doesn't bother to update the residual data count since it is known to be zero. Perform the zeroing manually before calculating the remaining data count. o Use multibyte in/out macros instead of shifting/masking by hand. aic79xx_inline.h: In ahd_setup_scb_common(), setup the SCB_XFERLEN_ODD field. aic79xx.reg: Use the SCB_TASK_ATTRIBUTE field as a bit field in the non-packetized case. We currently only define one bit, SCB_XFERLEN_ODD. Remove the ODD_SEG bit field that was used to carry the odd transfer length information through the SG cache. This is obviated by SCB_XFERLEN_ODD field. Remove the DATA_COUNT_ODD scratch ram byte that was used dynamicaly compute data transfer oddness. This is obviated by SCB_XFERLEN_ODD field. aic79xx.seq: Remove all updates to the DATA_COUNT_ODD scratch ram field. Remove all uses of ODD_SEG. These two save quite a few sequencer instructions. Use SCB_XFERLEN_ODD to validate the end of transfer ignore wide residue message case.
2003-05-26 21:26:52 +00:00
sgptr = ahd_inl_scbram(ahd, SCB_RESIDUAL_SGPTR);
data_cnt = ahd_inl_scbram(ahd, SCB_RESIDUAL_DATACNT);
if ((sgptr & SG_LIST_NULL) != 0) {
/*
* The residual data count is not updated
* for the command run to completion case.
* Explicitly zero the count.
*/
data_cnt &= ~AHD_SG_LEN_MASK;
}
data_addr = ahd_inq(ahd, SHADDR);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
data_cnt += 1;
data_addr -= 1;
Correct/Simplify ignore wide residue message handling aic79xx.c: In ahd_handle_ign_wide_residue(): o Use SCB_XFERLEN_ODD SCB field to determine transfer "oddness" rather than the DATA_COUNT_ODD logic. SCB_XFERLEN_ODD is toggled on every ignore wide residue message so that multiple ignore wide residue messages for the same transaction are properly supported. o If the sg list has been exausted, the sequencer doesn't bother to update the residual data count since it is known to be zero. Perform the zeroing manually before calculating the remaining data count. o Use multibyte in/out macros instead of shifting/masking by hand. aic79xx_inline.h: In ahd_setup_scb_common(), setup the SCB_XFERLEN_ODD field. aic79xx.reg: Use the SCB_TASK_ATTRIBUTE field as a bit field in the non-packetized case. We currently only define one bit, SCB_XFERLEN_ODD. Remove the ODD_SEG bit field that was used to carry the odd transfer length information through the SG cache. This is obviated by SCB_XFERLEN_ODD field. Remove the DATA_COUNT_ODD scratch ram byte that was used dynamicaly compute data transfer oddness. This is obviated by SCB_XFERLEN_ODD field. aic79xx.seq: Remove all updates to the DATA_COUNT_ODD scratch ram field. Remove all uses of ODD_SEG. These two save quite a few sequencer instructions. Use SCB_XFERLEN_ODD to validate the end of transfer ignore wide residue message case.
2003-05-26 21:26:52 +00:00
sgptr &= SG_PTR_MASK;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if ((ahd->flags & AHD_64BIT_ADDRESSING) != 0) {
struct ahd_dma64_seg *sg;
sg = ahd_sg_bus_to_virt(ahd, scb, sgptr);
/*
* The residual sg ptr points to the next S/G
* to load so we must go back one.
*/
sg--;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
sglen = aic_le32toh(sg->len) & AHD_SG_LEN_MASK;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if (sg != scb->sg_list
&& sglen < (data_cnt & AHD_SG_LEN_MASK)) {
sg--;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
sglen = aic_le32toh(sg->len);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*
* Preserve High Address and SG_LIST
* bits while setting the count to 1.
*/
data_cnt = 1|(sglen&(~AHD_SG_LEN_MASK));
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
data_addr = aic_le64toh(sg->addr)
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
+ (sglen & AHD_SG_LEN_MASK)
- 1;
/*
* Increment sg so it points to the
* "next" sg.
*/
sg++;
sgptr = ahd_sg_virt_to_bus(ahd, scb,
sg);
}
} else {
struct ahd_dma_seg *sg;
sg = ahd_sg_bus_to_virt(ahd, scb, sgptr);
/*
* The residual sg ptr points to the next S/G
* to load so we must go back one.
*/
sg--;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
sglen = aic_le32toh(sg->len) & AHD_SG_LEN_MASK;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if (sg != scb->sg_list
&& sglen < (data_cnt & AHD_SG_LEN_MASK)) {
sg--;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
sglen = aic_le32toh(sg->len);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*
* Preserve High Address and SG_LIST
* bits while setting the count to 1.
*/
data_cnt = 1|(sglen&(~AHD_SG_LEN_MASK));
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
data_addr = aic_le32toh(sg->addr)
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
+ (sglen & AHD_SG_LEN_MASK)
- 1;
/*
* Increment sg so it points to the
* "next" sg.
*/
sg++;
sgptr = ahd_sg_virt_to_bus(ahd, scb,
sg);
}
}
Correct/Simplify ignore wide residue message handling aic79xx.c: In ahd_handle_ign_wide_residue(): o Use SCB_XFERLEN_ODD SCB field to determine transfer "oddness" rather than the DATA_COUNT_ODD logic. SCB_XFERLEN_ODD is toggled on every ignore wide residue message so that multiple ignore wide residue messages for the same transaction are properly supported. o If the sg list has been exausted, the sequencer doesn't bother to update the residual data count since it is known to be zero. Perform the zeroing manually before calculating the remaining data count. o Use multibyte in/out macros instead of shifting/masking by hand. aic79xx_inline.h: In ahd_setup_scb_common(), setup the SCB_XFERLEN_ODD field. aic79xx.reg: Use the SCB_TASK_ATTRIBUTE field as a bit field in the non-packetized case. We currently only define one bit, SCB_XFERLEN_ODD. Remove the ODD_SEG bit field that was used to carry the odd transfer length information through the SG cache. This is obviated by SCB_XFERLEN_ODD field. Remove the DATA_COUNT_ODD scratch ram byte that was used dynamicaly compute data transfer oddness. This is obviated by SCB_XFERLEN_ODD field. aic79xx.seq: Remove all updates to the DATA_COUNT_ODD scratch ram field. Remove all uses of ODD_SEG. These two save quite a few sequencer instructions. Use SCB_XFERLEN_ODD to validate the end of transfer ignore wide residue message case.
2003-05-26 21:26:52 +00:00
/*
* Toggle the "oddness" of the transfer length
* to handle this mid-transfer ignore wide
* residue. This ensures that the oddness is
* correct for subsequent data transfers.
*/
ahd_outb(ahd, SCB_TASK_ATTRIBUTE,
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
ahd_inb_scbram(ahd, SCB_TASK_ATTRIBUTE)
^ SCB_XFERLEN_ODD);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
Correct/Simplify ignore wide residue message handling aic79xx.c: In ahd_handle_ign_wide_residue(): o Use SCB_XFERLEN_ODD SCB field to determine transfer "oddness" rather than the DATA_COUNT_ODD logic. SCB_XFERLEN_ODD is toggled on every ignore wide residue message so that multiple ignore wide residue messages for the same transaction are properly supported. o If the sg list has been exausted, the sequencer doesn't bother to update the residual data count since it is known to be zero. Perform the zeroing manually before calculating the remaining data count. o Use multibyte in/out macros instead of shifting/masking by hand. aic79xx_inline.h: In ahd_setup_scb_common(), setup the SCB_XFERLEN_ODD field. aic79xx.reg: Use the SCB_TASK_ATTRIBUTE field as a bit field in the non-packetized case. We currently only define one bit, SCB_XFERLEN_ODD. Remove the ODD_SEG bit field that was used to carry the odd transfer length information through the SG cache. This is obviated by SCB_XFERLEN_ODD field. Remove the DATA_COUNT_ODD scratch ram byte that was used dynamicaly compute data transfer oddness. This is obviated by SCB_XFERLEN_ODD field. aic79xx.seq: Remove all updates to the DATA_COUNT_ODD scratch ram field. Remove all uses of ODD_SEG. These two save quite a few sequencer instructions. Use SCB_XFERLEN_ODD to validate the end of transfer ignore wide residue message case.
2003-05-26 21:26:52 +00:00
ahd_outl(ahd, SCB_RESIDUAL_SGPTR, sgptr);
ahd_outl(ahd, SCB_RESIDUAL_DATACNT, data_cnt);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*
* The FIFO's pointers will be updated if/when the
* sequencer re-enters a data phase.
*/
}
}
}
/*
* Reinitialize the data pointers for the active transfer
* based on its current residual.
*/
static void
ahd_reinitialize_dataptrs(struct ahd_softc *ahd)
{
struct scb *scb;
ahd_mode_state saved_modes;
u_int scb_index;
u_int wait;
uint32_t sgptr;
uint32_t resid;
uint64_t dataptr;
AHD_ASSERT_MODES(ahd, AHD_MODE_DFF0_MSK|AHD_MODE_DFF1_MSK,
AHD_MODE_DFF0_MSK|AHD_MODE_DFF1_MSK);
scb_index = ahd_get_scbptr(ahd);
scb = ahd_lookup_scb(ahd, scb_index);
/*
* Release and reacquire the FIFO so we
* have a clean slate.
*/
ahd_outb(ahd, DFFSXFRCTL, CLRCHN);
wait = 1000;
Correct a typo in a comment. Add a comment in ahd_clear_critical_sections() about our need to leave ENBUSFREE set in SIMODE1 while single stepping. Re-arrange some delay loops so that we always perform a read after any register write and before the delay. This should make the delay loop more accurate. When completing message processing for a packetized commention, return the controller to a state where invalid non-packetized phases will still cause protocol violations. These are the same operations as those performed in the clear_target_state routine in the firmware. Now that we have a chip with working ABORTPENDING support (the 7901B), comment out the automatic use of this feature until we can adequately test it. The previous checkin updated the bug mask for the 7901B so this code was exercised. When resetting the bus, perform an ahd_flush_device_writes() call so that our reset assertion delay is acurately timed from when the reset bit is written to the controller.
2003-06-28 04:42:11 +00:00
while (--wait && !(ahd_inb(ahd, MDFFSTAT) & FIFOFREE))
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_delay(100);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if (wait == 0) {
ahd_print_path(ahd, scb);
printf("ahd_reinitialize_dataptrs: Forcing FIFO free.\n");
ahd_outb(ahd, DFFSXFRCTL, RSTCHN|CLRSHCNT);
}
saved_modes = ahd_save_modes(ahd);
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
ahd_outb(ahd, DFFSTAT,
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
ahd_inb(ahd, DFFSTAT)
| (saved_modes == 0x11 ? CURRFIFO_1 : CURRFIFO_0));
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*
* Determine initial values for data_addr and data_cnt
* for resuming the data phase.
*/
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
sgptr = ahd_inl_scbram(ahd, SCB_RESIDUAL_SGPTR);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
sgptr &= SG_PTR_MASK;
resid = (ahd_inb_scbram(ahd, SCB_RESIDUAL_DATACNT + 2) << 16)
| (ahd_inb_scbram(ahd, SCB_RESIDUAL_DATACNT + 1) << 8)
| ahd_inb_scbram(ahd, SCB_RESIDUAL_DATACNT);
if ((ahd->flags & AHD_64BIT_ADDRESSING) != 0) {
struct ahd_dma64_seg *sg;
sg = ahd_sg_bus_to_virt(ahd, scb, sgptr);
/* The residual sg_ptr always points to the next sg */
sg--;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
dataptr = aic_le64toh(sg->addr)
+ (aic_le32toh(sg->len) & AHD_SG_LEN_MASK)
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
- resid;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
ahd_outl(ahd, HADDR + 4, dataptr >> 32);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
} else {
struct ahd_dma_seg *sg;
sg = ahd_sg_bus_to_virt(ahd, scb, sgptr);
/* The residual sg_ptr always points to the next sg */
sg--;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
dataptr = aic_le32toh(sg->addr)
+ (aic_le32toh(sg->len) & AHD_SG_LEN_MASK)
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
- resid;
ahd_outb(ahd, HADDR + 4,
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
(aic_le32toh(sg->len) & ~AHD_SG_LEN_MASK) >> 24);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
ahd_outl(ahd, HADDR, dataptr);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_outb(ahd, HCNT + 2, resid >> 16);
ahd_outb(ahd, HCNT + 1, resid >> 8);
ahd_outb(ahd, HCNT, resid);
}
/*
* Handle the effects of issuing a bus device reset message.
*/
static void
ahd_handle_devreset(struct ahd_softc *ahd, struct ahd_devinfo *devinfo,
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
u_int lun, cam_status status, char *message,
int verbose_level)
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
{
#ifdef AHD_TARGET_MODE
struct ahd_tmode_tstate* tstate;
#endif
int found;
found = ahd_abort_scbs(ahd, devinfo->target, devinfo->channel,
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
lun, SCB_LIST_NULL, devinfo->role,
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
status);
#ifdef AHD_TARGET_MODE
/*
* Send an immediate notify ccb to all target mord peripheral
* drivers affected by this action.
*/
tstate = ahd->enabled_targets[devinfo->our_scsiid];
if (tstate != NULL) {
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
u_int cur_lun;
u_int max_lun;
if (lun != CAM_LUN_WILDCARD) {
cur_lun = 0;
max_lun = AHD_NUM_LUNS - 1;
} else {
cur_lun = lun;
max_lun = lun;
}
for (cur_lun <= max_lun; cur_lun++) {
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
struct ahd_tmode_lstate* lstate;
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
lstate = tstate->enabled_luns[cur_lun];
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if (lstate == NULL)
continue;
ahd_queue_lstate_event(ahd, lstate, devinfo->our_scsiid,
MSG_BUS_DEV_RESET, /*arg*/0);
ahd_send_lstate_events(ahd, lstate);
}
}
#endif
/*
* Go back to async/narrow transfers and renegotiate.
*/
ahd_set_width(ahd, devinfo, MSG_EXT_WDTR_BUS_8_BIT,
AHD_TRANS_CUR, /*paused*/TRUE);
ahd_set_syncrate(ahd, devinfo, /*period*/0, /*offset*/0,
/*ppr_options*/0, AHD_TRANS_CUR, /*paused*/TRUE);
ahd_send_async(ahd, devinfo->channel, devinfo->target,
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
lun, AC_SENT_BDR, NULL);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if (message != NULL
&& (verbose_level <= bootverbose))
printf("%s: %s on %c:%d. %d SCBs aborted\n", ahd_name(ahd),
message, devinfo->channel, devinfo->target, found);
}
#ifdef AHD_TARGET_MODE
static void
ahd_setup_target_msgin(struct ahd_softc *ahd, struct ahd_devinfo *devinfo,
struct scb *scb)
{
/*
* To facilitate adding multiple messages together,
* each routine should increment the index and len
* variables instead of setting them explicitly.
*/
ahd->msgout_index = 0;
ahd->msgout_len = 0;
if (scb != NULL && (scb->flags & SCB_AUTO_NEGOTIATE) != 0)
ahd_build_transfer_msg(ahd, devinfo);
else
panic("ahd_intr: AWAITING target message with no message");
ahd->msgout_index = 0;
ahd->msg_type = MSG_TYPE_TARGET_MSGIN;
}
#endif
/**************************** Initialization **********************************/
Use better return types and a couple of casts to eliminate warnings on alpha. This will take the file out of sync with the private version that we maintain, but alpha tinderbox has been broken for too long. Tested on: i386, sparc64, alpha
2002-11-12 10:22:49 +00:00
static u_int
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_sglist_size(struct ahd_softc *ahd)
{
bus_size_t list_size;
list_size = sizeof(struct ahd_dma_seg) * AHD_NSEG;
if ((ahd->flags & AHD_64BIT_ADDRESSING) != 0)
list_size = sizeof(struct ahd_dma64_seg) * AHD_NSEG;
return (list_size);
}
/*
* Calculate the optimum S/G List allocation size. S/G elements used
* for a given transaction must be physically contiguous. Assume the
* OS will allocate full pages to us, so it doesn't make sense to request
* less than a page.
*/
Use better return types and a couple of casts to eliminate warnings on alpha. This will take the file out of sync with the private version that we maintain, but alpha tinderbox has been broken for too long. Tested on: i386, sparc64, alpha
2002-11-12 10:22:49 +00:00
static u_int
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_sglist_allocsize(struct ahd_softc *ahd)
{
bus_size_t sg_list_increment;
bus_size_t sg_list_size;
bus_size_t max_list_size;
bus_size_t best_list_size;
/* Start out with the minimum required for AHD_NSEG. */
sg_list_increment = ahd_sglist_size(ahd);
sg_list_size = sg_list_increment;
/* Get us as close as possible to a page in size. */
while ((sg_list_size + sg_list_increment) <= PAGE_SIZE)
sg_list_size += sg_list_increment;
/*
* Try to reduce the amount of wastage by allocating
* multiple pages.
*/
best_list_size = sg_list_size;
max_list_size = roundup(sg_list_increment, PAGE_SIZE);
if (max_list_size < 4 * PAGE_SIZE)
max_list_size = 4 * PAGE_SIZE;
if (max_list_size > (AHD_SCB_MAX_ALLOC * sg_list_increment))
max_list_size = (AHD_SCB_MAX_ALLOC * sg_list_increment);
while ((sg_list_size + sg_list_increment) <= max_list_size
&& (sg_list_size % PAGE_SIZE) != 0) {
bus_size_t new_mod;
bus_size_t best_mod;
sg_list_size += sg_list_increment;
new_mod = sg_list_size % PAGE_SIZE;
best_mod = best_list_size % PAGE_SIZE;
if (new_mod > best_mod || new_mod == 0) {
best_list_size = sg_list_size;
}
}
return (best_list_size);
}
/*
* Allocate a controller structure for a new device
* and perform initial initializion.
*/
struct ahd_softc *
ahd_alloc(void *platform_arg, char *name)
{
struct ahd_softc *ahd;
#ifndef __FreeBSD__
ahd = malloc(sizeof(*ahd), M_DEVBUF, M_NOWAIT);
if (!ahd) {
printf("aic7xxx: cannot malloc softc!\n");
free(name, M_DEVBUF);
return NULL;
}
#else
ahd = device_get_softc((device_t)platform_arg);
#endif
memset(ahd, 0, sizeof(*ahd));
ahd->seep_config = malloc(sizeof(*ahd->seep_config),
M_DEVBUF, M_NOWAIT);
if (ahd->seep_config == NULL) {
#ifndef __FreeBSD__
free(ahd, M_DEVBUF);
#endif
free(name, M_DEVBUF);
return (NULL);
}
LIST_INIT(&ahd->pending_scbs);
/* We don't know our unit number until the OSM sets it */
ahd->name = name;
ahd->unit = -1;
ahd->description = NULL;
ahd->bus_description = NULL;
ahd->channel = 'A';
ahd->chip = AHD_NONE;
ahd->features = AHD_FENONE;
ahd->bugs = AHD_BUGNONE;
ahd->flags = AHD_SPCHK_ENB_A|AHD_RESET_BUS_A|AHD_TERM_ENB_A
| AHD_EXTENDED_TRANS_A|AHD_STPWLEVEL_A;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_timer_init(&ahd->reset_timer);
aic_timer_init(&ahd->stat_timer);
Fixup spelling of "coalesce" and derivatives. Approved by: RE
2003-05-26 21:10:58 +00:00
ahd->int_coalescing_timer = AHD_INT_COALESCING_TIMER_DEFAULT;
ahd->int_coalescing_maxcmds = AHD_INT_COALESCING_MAXCMDS_DEFAULT;
ahd->int_coalescing_mincmds = AHD_INT_COALESCING_MINCMDS_DEFAULT;
ahd->int_coalescing_threshold = AHD_INT_COALESCING_THRESHOLD_DEFAULT;
ahd->int_coalescing_stop_threshold =
AHD_INT_COALESCING_STOP_THRESHOLD_DEFAULT;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if (ahd_platform_alloc(ahd, platform_arg) != 0) {
ahd_free(ahd);
ahd = NULL;
}
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_MEMORY) != 0) {
Use better return types and a couple of casts to eliminate warnings on alpha. This will take the file out of sync with the private version that we maintain, but alpha tinderbox has been broken for too long. Tested on: i386, sparc64, alpha
2002-11-12 10:22:49 +00:00
printf("%s: scb size = 0x%x, hscb size = 0x%x\n",
ahd_name(ahd), (u_int)sizeof(struct scb),
(u_int)sizeof(struct hardware_scb));
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
}
#endif
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
return (ahd);
}
int
ahd_softc_init(struct ahd_softc *ahd)
{
ahd->unpause = 0;
ahd->pause = PAUSE;
return (0);
}
void
ahd_softc_insert(struct ahd_softc *ahd)
{
struct ahd_softc *list_ahd;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
#if AIC_PCI_CONFIG > 0
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*
* Second Function PCI devices need to inherit some
* settings from function 0.
*/
if ((ahd->features & AHD_MULTI_FUNC) != 0) {
TAILQ_FOREACH(list_ahd, &ahd_tailq, links) {
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_dev_softc_t list_pci;
aic_dev_softc_t pci;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
list_pci = list_ahd->dev_softc;
pci = ahd->dev_softc;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
if (aic_get_pci_slot(list_pci) == aic_get_pci_slot(pci)
&& aic_get_pci_bus(list_pci) == aic_get_pci_bus(pci)) {
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
struct ahd_softc *master;
struct ahd_softc *slave;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
if (aic_get_pci_function(list_pci) == 0) {
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
master = list_ahd;
slave = ahd;
} else {
master = ahd;
slave = list_ahd;
}
slave->flags &= ~AHD_BIOS_ENABLED;
slave->flags |=
master->flags & AHD_BIOS_ENABLED;
break;
}
}
}
#endif
/*
* Insertion sort into our list of softcs.
*/
list_ahd = TAILQ_FIRST(&ahd_tailq);
while (list_ahd != NULL
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
&& ahd_softc_comp(ahd, list_ahd) <= 0)
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
list_ahd = TAILQ_NEXT(list_ahd, links);
if (list_ahd != NULL)
TAILQ_INSERT_BEFORE(list_ahd, ahd, links);
else
TAILQ_INSERT_TAIL(&ahd_tailq, ahd, links);
ahd->init_level++;
}
/*
* Verify that the passed in softc pointer is for a
* controller that is still configured.
*/
struct ahd_softc *
ahd_find_softc(struct ahd_softc *ahd)
{
struct ahd_softc *list_ahd;
TAILQ_FOREACH(list_ahd, &ahd_tailq, links) {
if (list_ahd == ahd)
return (ahd);
}
return (NULL);
}
void
ahd_set_unit(struct ahd_softc *ahd, int unit)
{
ahd->unit = unit;
}
void
ahd_set_name(struct ahd_softc *ahd, char *name)
{
if (ahd->name != NULL)
free(ahd->name, M_DEVBUF);
ahd->name = name;
}
void
ahd_free(struct ahd_softc *ahd)
{
int i;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
ahd_terminate_recovery_thread(ahd);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
switch (ahd->init_level) {
default:
case 5:
ahd_shutdown(ahd);
/* FALLTHROUGH */
case 4:
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_dmamap_unload(ahd, ahd->shared_data_dmat,
ahd->shared_data_map.dmamap);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/* FALLTHROUGH */
case 3:
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_dmamem_free(ahd, ahd->shared_data_dmat, ahd->qoutfifo,
ahd->shared_data_map.dmamap);
aic_dmamap_destroy(ahd, ahd->shared_data_dmat,
ahd->shared_data_map.dmamap);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/* FALLTHROUGH */
case 2:
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_dma_tag_destroy(ahd, ahd->shared_data_dmat);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
case 1:
#ifndef __linux__
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_dma_tag_destroy(ahd, ahd->buffer_dmat);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
#endif
break;
case 0:
break;
}
#ifndef __linux__
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_dma_tag_destroy(ahd, ahd->parent_dmat);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
#endif
ahd_platform_free(ahd);
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
ahd_fini_scbdata(ahd);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
for (i = 0; i < AHD_NUM_TARGETS; i++) {
struct ahd_tmode_tstate *tstate;
tstate = ahd->enabled_targets[i];
if (tstate != NULL) {
#if AHD_TARGET_MODE
int j;
for (j = 0; j < AHD_NUM_LUNS; j++) {
struct ahd_tmode_lstate *lstate;
lstate = tstate->enabled_luns[j];
if (lstate != NULL) {
xpt_free_path(lstate->path);
free(lstate, M_DEVBUF);
}
}
#endif
free(tstate, M_DEVBUF);
}
}
#if AHD_TARGET_MODE
if (ahd->black_hole != NULL) {
xpt_free_path(ahd->black_hole->path);
free(ahd->black_hole, M_DEVBUF);
}
#endif
if (ahd->name != NULL)
free(ahd->name, M_DEVBUF);
if (ahd->seep_config != NULL)
free(ahd->seep_config, M_DEVBUF);
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
if (ahd->saved_stack != NULL)
free(ahd->saved_stack, M_DEVBUF);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
#ifndef __FreeBSD__
free(ahd, M_DEVBUF);
#endif
return;
}
void
ahd_shutdown(void *arg)
{
struct ahd_softc *ahd;
ahd = (struct ahd_softc *)arg;
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
/*
* Stop periodic timer callbacks.
*/
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_timer_stop(&ahd->reset_timer);
aic_timer_stop(&ahd->stat_timer);
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/* This will reset most registers to 0, but not all */
aic7770.c: aic79xx.c: aic79xx.h: aic79xx_pci.c: aic7xxx.c: aic7xxx.h: aic7xxx_pci.c: Switch ah?_reset() to take an additional "reinit" argument. Use this instead of init_level to determin if the chip should be fully reinitialized after a chip reset. This is required so that ah?_shutdown() can reset the chip without side-effects. aic79xx.c: Implement ahd_suspend() and ahd_resume(). aic7xxx.c: Change ahc_loadseq() to *not* restart the sequencer. This brings the loadseq behavior in line with that of the 7902 driver and also simplifies the init routine. Correct the resume routine to enable interrupts and restart the sequencer.
2003-06-06 23:48:19 +00:00
ahd_reset(ahd, /*reinit*/FALSE);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
/*
* Reset the controller and record some information about it
aic7770.c: aic79xx.c: aic79xx.h: aic79xx_pci.c: aic7xxx.c: aic7xxx.h: aic7xxx_pci.c: Switch ah?_reset() to take an additional "reinit" argument. Use this instead of init_level to determin if the chip should be fully reinitialized after a chip reset. This is required so that ah?_shutdown() can reset the chip without side-effects. aic79xx.c: Implement ahd_suspend() and ahd_resume(). aic7xxx.c: Change ahc_loadseq() to *not* restart the sequencer. This brings the loadseq behavior in line with that of the 7902 driver and also simplifies the init routine. Correct the resume routine to enable interrupts and restart the sequencer.
2003-06-06 23:48:19 +00:00
* that is only available just after a reset. If "reinit" is
* non-zero, this reset occured after initial configuration
* and the caller requests that the chip be fully reinitialized
* to a runable state. Chip interrupts are *not* enabled after
* a reinitialization. The caller must enable interrupts via
* ahd_intr_enable().
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
*/
int
aic7770.c: aic79xx.c: aic79xx.h: aic79xx_pci.c: aic7xxx.c: aic7xxx.h: aic7xxx_pci.c: Switch ah?_reset() to take an additional "reinit" argument. Use this instead of init_level to determin if the chip should be fully reinitialized after a chip reset. This is required so that ah?_shutdown() can reset the chip without side-effects. aic79xx.c: Implement ahd_suspend() and ahd_resume(). aic7xxx.c: Change ahc_loadseq() to *not* restart the sequencer. This brings the loadseq behavior in line with that of the 7902 driver and also simplifies the init routine. Correct the resume routine to enable interrupts and restart the sequencer.
2003-06-06 23:48:19 +00:00
ahd_reset(struct ahd_softc *ahd, int reinit)
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
{
u_int sxfrctl1;
int wait;
uint32_t cmd;
/*
* Preserve the value of the SXFRCTL1 register for all channels.
* It contains settings that affect termination and we don't want
* to disturb the integrity of the bus.
*/
ahd_pause(ahd);
aic79xx.c: Include read streaming in the PPR flags we display in diagnostics. In ahd_reset(), set the known mode after our initial pause prior to setting the mode. We can't just set the mode directly because the current mode, after the pause, is most likely unknown and setting the mode when the saved mode is unknown will trigger an assertion in the mode debug code. Complete an audit for SCB RAM reads. These reads must be performed via the special ahd_in?_scbram() methods so we can perform a Rev A. PCI-X workaround. Remove a superfluous mode save operation that was performed just prior to a call to ahd_clear_critical_section(). The saved mode was never restored and wouldn't have been valid anyway since the mode could change while single stepping out of a critical section. aic79xx.h: Add new BUG definition AHD_PCIX_SCBRAM_RD_BUG. aic79xx_inline.h: Update ahd_inb_scbram routine to check for AHD_PCIX_SCBRAM_RD_BUG and only apply the workaround if this bug is active. The old code applied the workaround in all cases. aic79xx_pci.c: Set AHD_PCIX_SCBRAM_RD_BUG for the A4. Remove an attempted saved_modes call in ahd_pci_test_register_access(). Saving the modes can only occur when we are paused, but the call was happening before the chip was known to be paused. Restoring the modes doesn't make sense either since the code makes no assumptions about the state of the sequencer until the first time the mode is set by the driver. This happens after the registers are successfully mapped.
2003-03-06 23:58:34 +00:00
ahd_update_modes(ahd);
aic79xx.c: Clear the LQICRC_NLQ status should it pop up after we have already handled the SCSIPERR. During some streaming operations this status can be delayed until the stream ends. Without this change, the driver would complain about a "Missing case in ahd_handle_scsiint". In the LQOBUSFREE handler... Don't return the LQOMGR back to the idle state until after we have cleaned up ENSELO and any status related to this selection. The last thing we need is the LQO manager starting another select-out before we have updated the execution queue. It is not clear whether the LQOMGR would, or would not start a new selection early. Make sure ENSELO is off prior to clearing SELDO by flushing device writes. Move assignment of the next target SCB pointer inside of an if to make the code clearer. The effect is the same. Dump card state in both "Unexpected PKT busfree" paths. In ahd_reset(), set the chip to SCSI mode before reading SXFRCTL1. That register only exists in the SCSI mode. Also set the mode explicitly to the SCSI mode after chip reset due to paranoia. Re-arrange code so that SXFRCTL1 is restored as quickly after the chip reset as possible. S/G structurs must be 8byte aligned. Make this official by saying so in our DMA tag. Disable CIO bus stretch on MDFFSTAT if SHVALID is about to come true. This can cause a CIO bus lockup if a PCI or PCI-X error occurs while the stretch is occurring - the host cannot service the PCI-X error since the CIO bus is locked out and SHVALID will never resolve. The stretch was added in the Rev B to simplify the wait for SHVALID to resolve, but the code to do this in the open source sequencer is so simple it was never removed. Consistently use MAX_OFFSET for the user max syncrate set from non-volatile storage. This ensures that the offset does not conflict with AH?_OFFSET_UNKNOWN. Have ahd_pause_and_flushwork set the mode to ensure that it has access to the registers it checks. Also modify the checking of intstat so that the check against 0xFF can actually succeed if the INT_PEND mask is something other than 0xFF. Although there are no cardbus U320 controllers, this check may be needed to recover from a hot-plug PCI removal that occurs without informing the driver. Fix a typo. sg_prefetch_cnt -> sg_prefetch_align. This fixes an infinite loop at card initialization if the cacheline size is 0. aic79xx.h: Add AHD_EARLY_REQ_BUG bug flag. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. Change AH?_OFFSET_UNKNOWN to 0xFF. This is a value that the curr->offset can never be, unlike '0' which we previously used. This fixes code that only checks for a non-zero offset to determine if a sync negotiation is required since it will fire in the unknown case even if the goal is async. aic79xx.reg: Add comments for LQISTAT bits indicating their names in the 7902 data book. We use slightly different and more descriptive names in the firmware. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. aic79xx.seq: Update comments regarding rundown of the GSFIFO to reflect reality. Fix spelling errors. Since we use an 8byte address and 1 byte length, shorten the size of a block move for the legacy DMA'ed CDB case from 11 to 9 bytes. Remove code that, assuming the abort pending feature worked, would set MK_MESSAGE in the SCB's control byte on completion to catch invalid reselections. Since we don't see interrupts for completed selections, this status update could occur prior to us noticing the SELDO. The "select-out" queue logic will get confused by the MK_MESSAGE bit being set as this is used to catch packatized connections where we select-out with ATN. Since the abort pending feature doesn't work on any released controllers yet, this code was never executed. Add support for the AHD_EARLY_REQ_BUG. Don't ignore persistent REQ assertions just because they were asserted within the bus settle delay window. This allows us to tolerate devices like the GEM318 that violate the SCSI spec. Remove unintentional settnig of SG_CACHE_AVAIL. Writing this bit should have no effect, but who knows... On the Rev A, we must wait for HDMAENACK before loading additional segments to avoid clobbering the address of the first segment in the S/G FIFO. This resolves data-corruption issues with certain IBM (now Hitachi) and Fujitsu U320 drives. Rearrange calc_residual to avoid an extra jmp instruction. On RevA Silicon, if the target returns us to data-out after we have already trained for data-out, it is possible for us to transition the free running clock to data-valid before the required 100ns P1 setup time (8 P1 assertions in fast-160 mode). This will only happen if this L-Q is a continuation of a data transfer for which we have already prefetched data into our FIFO (LQ/Data followed by LQ/Data for the same write transaction). This can cause some target implementations to miss the first few data transfers on the bus. We detect this situation by noticing that this is the first data transfer after an LQ (LQIWORKONLQ true), that the data transfer is a continuation of a transfer already setup in our FIFO (SAVEPTRS interrupt), and that the transaction is a write (DIRECTION set in DFCNTRL). The delay is performed by disabling SCSIEN until we see the first REQ from the target. Only compile in snapshot savepointers handler for RevA silicon where it is enabled. Handle the cfg4icmd packetized interrupt. We just need to load the address and count, start the DMA, and CLRCHN once the transfer is complete. Fix an oversight in the overrun handler for packetized status operations. We need to wait for either CTXTDONE or an overrun when checking for an overrun. The previous code did not wait and thus could decide that no overrun had occurred even though an overrun will occur on the next data-valid req. Add some comment to this section for clarity. Use LAST_SEG_DONE instead of LASTSDONE for testing transfer completion in the packetized status case. LASTSDONE may come up more quickly since it only records completion on the SCSI side, but since LAST_SEG_DONE is used everywhere else (and needs to be), this is less confusing. Add a missing invalidation of the longjmp address in the non-pack handler. This code needs additional review. aic79xx_inline.h: Fix spelling error. aic79xx_osm.c: Set the cdb length for CDBs dma'ed from host memory. Add a comment indicating that, should CAM start supporting cdbs larger than 16bytes, the driver could store the CDB in the status buffer. aic79xx_pci.c: Add a table entry for the 39320A. Added a missing comma to an error string table. Fix spelling errors.
2003-02-27 23:23:16 +00:00
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
sxfrctl1 = ahd_inb(ahd, SXFRCTL1);
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
cmd = aic_pci_read_config(ahd->dev_softc, PCIR_COMMAND, /*bytes*/2);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if ((ahd->bugs & AHD_PCIX_CHIPRST_BUG) != 0) {
uint32_t mod_cmd;
/*
* A4 Razor #632
* During the assertion of CHIPRST, the chip
* does not disable its parity logic prior to
* the start of the reset. This may cause a
* parity error to be detected and thus a
* spurious SERR or PERR assertion. Disble
* PERR and SERR responses during the CHIPRST.
*/
mod_cmd = cmd & ~(PCIM_CMD_PERRESPEN|PCIM_CMD_SERRESPEN);
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_pci_write_config(ahd->dev_softc, PCIR_COMMAND,
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
mod_cmd, /*bytes*/2);
}
ahd_outb(ahd, HCNTRL, CHIPRST | ahd->pause);
/*
* Ensure that the reset has finished. We delay 1000us
* prior to reading the register to make sure the chip
* has sufficiently completed its reset to handle register
* accesses.
*/
wait = 1000;
do {
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_delay(1000);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
} while (--wait && !(ahd_inb(ahd, HCNTRL) & CHIPRSTACK));
if (wait == 0) {
printf("%s: WARNING - Failed chip reset! "
"Trying to initialize anyway.\n", ahd_name(ahd));
}
ahd_outb(ahd, HCNTRL, ahd->pause);
if ((ahd->bugs & AHD_PCIX_CHIPRST_BUG) != 0) {
/*
* Clear any latched PCI error status and restore
* previous SERR and PERR response enables.
*/
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_pci_write_config(ahd->dev_softc, PCIR_STATUS + 1,
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
0xFF, /*bytes*/1);
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_pci_write_config(ahd->dev_softc, PCIR_COMMAND,
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
cmd, /*bytes*/2);
}
aic79xx.c: Clear the LQICRC_NLQ status should it pop up after we have already handled the SCSIPERR. During some streaming operations this status can be delayed until the stream ends. Without this change, the driver would complain about a "Missing case in ahd_handle_scsiint". In the LQOBUSFREE handler... Don't return the LQOMGR back to the idle state until after we have cleaned up ENSELO and any status related to this selection. The last thing we need is the LQO manager starting another select-out before we have updated the execution queue. It is not clear whether the LQOMGR would, or would not start a new selection early. Make sure ENSELO is off prior to clearing SELDO by flushing device writes. Move assignment of the next target SCB pointer inside of an if to make the code clearer. The effect is the same. Dump card state in both "Unexpected PKT busfree" paths. In ahd_reset(), set the chip to SCSI mode before reading SXFRCTL1. That register only exists in the SCSI mode. Also set the mode explicitly to the SCSI mode after chip reset due to paranoia. Re-arrange code so that SXFRCTL1 is restored as quickly after the chip reset as possible. S/G structurs must be 8byte aligned. Make this official by saying so in our DMA tag. Disable CIO bus stretch on MDFFSTAT if SHVALID is about to come true. This can cause a CIO bus lockup if a PCI or PCI-X error occurs while the stretch is occurring - the host cannot service the PCI-X error since the CIO bus is locked out and SHVALID will never resolve. The stretch was added in the Rev B to simplify the wait for SHVALID to resolve, but the code to do this in the open source sequencer is so simple it was never removed. Consistently use MAX_OFFSET for the user max syncrate set from non-volatile storage. This ensures that the offset does not conflict with AH?_OFFSET_UNKNOWN. Have ahd_pause_and_flushwork set the mode to ensure that it has access to the registers it checks. Also modify the checking of intstat so that the check against 0xFF can actually succeed if the INT_PEND mask is something other than 0xFF. Although there are no cardbus U320 controllers, this check may be needed to recover from a hot-plug PCI removal that occurs without informing the driver. Fix a typo. sg_prefetch_cnt -> sg_prefetch_align. This fixes an infinite loop at card initialization if the cacheline size is 0. aic79xx.h: Add AHD_EARLY_REQ_BUG bug flag. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. Change AH?_OFFSET_UNKNOWN to 0xFF. This is a value that the curr->offset can never be, unlike '0' which we previously used. This fixes code that only checks for a non-zero offset to determine if a sync negotiation is required since it will fire in the unknown case even if the goal is async. aic79xx.reg: Add comments for LQISTAT bits indicating their names in the 7902 data book. We use slightly different and more descriptive names in the firmware. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. aic79xx.seq: Update comments regarding rundown of the GSFIFO to reflect reality. Fix spelling errors. Since we use an 8byte address and 1 byte length, shorten the size of a block move for the legacy DMA'ed CDB case from 11 to 9 bytes. Remove code that, assuming the abort pending feature worked, would set MK_MESSAGE in the SCB's control byte on completion to catch invalid reselections. Since we don't see interrupts for completed selections, this status update could occur prior to us noticing the SELDO. The "select-out" queue logic will get confused by the MK_MESSAGE bit being set as this is used to catch packatized connections where we select-out with ATN. Since the abort pending feature doesn't work on any released controllers yet, this code was never executed. Add support for the AHD_EARLY_REQ_BUG. Don't ignore persistent REQ assertions just because they were asserted within the bus settle delay window. This allows us to tolerate devices like the GEM318 that violate the SCSI spec. Remove unintentional settnig of SG_CACHE_AVAIL. Writing this bit should have no effect, but who knows... On the Rev A, we must wait for HDMAENACK before loading additional segments to avoid clobbering the address of the first segment in the S/G FIFO. This resolves data-corruption issues with certain IBM (now Hitachi) and Fujitsu U320 drives. Rearrange calc_residual to avoid an extra jmp instruction. On RevA Silicon, if the target returns us to data-out after we have already trained for data-out, it is possible for us to transition the free running clock to data-valid before the required 100ns P1 setup time (8 P1 assertions in fast-160 mode). This will only happen if this L-Q is a continuation of a data transfer for which we have already prefetched data into our FIFO (LQ/Data followed by LQ/Data for the same write transaction). This can cause some target implementations to miss the first few data transfers on the bus. We detect this situation by noticing that this is the first data transfer after an LQ (LQIWORKONLQ true), that the data transfer is a continuation of a transfer already setup in our FIFO (SAVEPTRS interrupt), and that the transaction is a write (DIRECTION set in DFCNTRL). The delay is performed by disabling SCSIEN until we see the first REQ from the target. Only compile in snapshot savepointers handler for RevA silicon where it is enabled. Handle the cfg4icmd packetized interrupt. We just need to load the address and count, start the DMA, and CLRCHN once the transfer is complete. Fix an oversight in the overrun handler for packetized status operations. We need to wait for either CTXTDONE or an overrun when checking for an overrun. The previous code did not wait and thus could decide that no overrun had occurred even though an overrun will occur on the next data-valid req. Add some comment to this section for clarity. Use LAST_SEG_DONE instead of LASTSDONE for testing transfer completion in the packetized status case. LASTSDONE may come up more quickly since it only records completion on the SCSI side, but since LAST_SEG_DONE is used everywhere else (and needs to be), this is less confusing. Add a missing invalidation of the longjmp address in the non-pack handler. This code needs additional review. aic79xx_inline.h: Fix spelling error. aic79xx_osm.c: Set the cdb length for CDBs dma'ed from host memory. Add a comment indicating that, should CAM start supporting cdbs larger than 16bytes, the driver could store the CDB in the status buffer. aic79xx_pci.c: Add a table entry for the 39320A. Added a missing comma to an error string table. Fix spelling errors.
2003-02-27 23:23:16 +00:00
/*
* Mode should be SCSI after a chip reset, but lets
aic79xx.c: Include read streaming in the PPR flags we display in diagnostics. In ahd_reset(), set the known mode after our initial pause prior to setting the mode. We can't just set the mode directly because the current mode, after the pause, is most likely unknown and setting the mode when the saved mode is unknown will trigger an assertion in the mode debug code. Complete an audit for SCB RAM reads. These reads must be performed via the special ahd_in?_scbram() methods so we can perform a Rev A. PCI-X workaround. Remove a superfluous mode save operation that was performed just prior to a call to ahd_clear_critical_section(). The saved mode was never restored and wouldn't have been valid anyway since the mode could change while single stepping out of a critical section. aic79xx.h: Add new BUG definition AHD_PCIX_SCBRAM_RD_BUG. aic79xx_inline.h: Update ahd_inb_scbram routine to check for AHD_PCIX_SCBRAM_RD_BUG and only apply the workaround if this bug is active. The old code applied the workaround in all cases. aic79xx_pci.c: Set AHD_PCIX_SCBRAM_RD_BUG for the A4. Remove an attempted saved_modes call in ahd_pci_test_register_access(). Saving the modes can only occur when we are paused, but the call was happening before the chip was known to be paused. Restoring the modes doesn't make sense either since the code makes no assumptions about the state of the sequencer until the first time the mode is set by the driver. This happens after the registers are successfully mapped.
2003-03-06 23:58:34 +00:00
* set it just to be safe. We touch the MODE_PTR
* register directly so as to bypass the lazy update
* code in ahd_set_modes().
aic79xx.c: Clear the LQICRC_NLQ status should it pop up after we have already handled the SCSIPERR. During some streaming operations this status can be delayed until the stream ends. Without this change, the driver would complain about a "Missing case in ahd_handle_scsiint". In the LQOBUSFREE handler... Don't return the LQOMGR back to the idle state until after we have cleaned up ENSELO and any status related to this selection. The last thing we need is the LQO manager starting another select-out before we have updated the execution queue. It is not clear whether the LQOMGR would, or would not start a new selection early. Make sure ENSELO is off prior to clearing SELDO by flushing device writes. Move assignment of the next target SCB pointer inside of an if to make the code clearer. The effect is the same. Dump card state in both "Unexpected PKT busfree" paths. In ahd_reset(), set the chip to SCSI mode before reading SXFRCTL1. That register only exists in the SCSI mode. Also set the mode explicitly to the SCSI mode after chip reset due to paranoia. Re-arrange code so that SXFRCTL1 is restored as quickly after the chip reset as possible. S/G structurs must be 8byte aligned. Make this official by saying so in our DMA tag. Disable CIO bus stretch on MDFFSTAT if SHVALID is about to come true. This can cause a CIO bus lockup if a PCI or PCI-X error occurs while the stretch is occurring - the host cannot service the PCI-X error since the CIO bus is locked out and SHVALID will never resolve. The stretch was added in the Rev B to simplify the wait for SHVALID to resolve, but the code to do this in the open source sequencer is so simple it was never removed. Consistently use MAX_OFFSET for the user max syncrate set from non-volatile storage. This ensures that the offset does not conflict with AH?_OFFSET_UNKNOWN. Have ahd_pause_and_flushwork set the mode to ensure that it has access to the registers it checks. Also modify the checking of intstat so that the check against 0xFF can actually succeed if the INT_PEND mask is something other than 0xFF. Although there are no cardbus U320 controllers, this check may be needed to recover from a hot-plug PCI removal that occurs without informing the driver. Fix a typo. sg_prefetch_cnt -> sg_prefetch_align. This fixes an infinite loop at card initialization if the cacheline size is 0. aic79xx.h: Add AHD_EARLY_REQ_BUG bug flag. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. Change AH?_OFFSET_UNKNOWN to 0xFF. This is a value that the curr->offset can never be, unlike '0' which we previously used. This fixes code that only checks for a non-zero offset to determine if a sync negotiation is required since it will fire in the unknown case even if the goal is async. aic79xx.reg: Add comments for LQISTAT bits indicating their names in the 7902 data book. We use slightly different and more descriptive names in the firmware. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. aic79xx.seq: Update comments regarding rundown of the GSFIFO to reflect reality. Fix spelling errors. Since we use an 8byte address and 1 byte length, shorten the size of a block move for the legacy DMA'ed CDB case from 11 to 9 bytes. Remove code that, assuming the abort pending feature worked, would set MK_MESSAGE in the SCB's control byte on completion to catch invalid reselections. Since we don't see interrupts for completed selections, this status update could occur prior to us noticing the SELDO. The "select-out" queue logic will get confused by the MK_MESSAGE bit being set as this is used to catch packatized connections where we select-out with ATN. Since the abort pending feature doesn't work on any released controllers yet, this code was never executed. Add support for the AHD_EARLY_REQ_BUG. Don't ignore persistent REQ assertions just because they were asserted within the bus settle delay window. This allows us to tolerate devices like the GEM318 that violate the SCSI spec. Remove unintentional settnig of SG_CACHE_AVAIL. Writing this bit should have no effect, but who knows... On the Rev A, we must wait for HDMAENACK before loading additional segments to avoid clobbering the address of the first segment in the S/G FIFO. This resolves data-corruption issues with certain IBM (now Hitachi) and Fujitsu U320 drives. Rearrange calc_residual to avoid an extra jmp instruction. On RevA Silicon, if the target returns us to data-out after we have already trained for data-out, it is possible for us to transition the free running clock to data-valid before the required 100ns P1 setup time (8 P1 assertions in fast-160 mode). This will only happen if this L-Q is a continuation of a data transfer for which we have already prefetched data into our FIFO (LQ/Data followed by LQ/Data for the same write transaction). This can cause some target implementations to miss the first few data transfers on the bus. We detect this situation by noticing that this is the first data transfer after an LQ (LQIWORKONLQ true), that the data transfer is a continuation of a transfer already setup in our FIFO (SAVEPTRS interrupt), and that the transaction is a write (DIRECTION set in DFCNTRL). The delay is performed by disabling SCSIEN until we see the first REQ from the target. Only compile in snapshot savepointers handler for RevA silicon where it is enabled. Handle the cfg4icmd packetized interrupt. We just need to load the address and count, start the DMA, and CLRCHN once the transfer is complete. Fix an oversight in the overrun handler for packetized status operations. We need to wait for either CTXTDONE or an overrun when checking for an overrun. The previous code did not wait and thus could decide that no overrun had occurred even though an overrun will occur on the next data-valid req. Add some comment to this section for clarity. Use LAST_SEG_DONE instead of LASTSDONE for testing transfer completion in the packetized status case. LASTSDONE may come up more quickly since it only records completion on the SCSI side, but since LAST_SEG_DONE is used everywhere else (and needs to be), this is less confusing. Add a missing invalidation of the longjmp address in the non-pack handler. This code needs additional review. aic79xx_inline.h: Fix spelling error. aic79xx_osm.c: Set the cdb length for CDBs dma'ed from host memory. Add a comment indicating that, should CAM start supporting cdbs larger than 16bytes, the driver could store the CDB in the status buffer. aic79xx_pci.c: Add a table entry for the 39320A. Added a missing comma to an error string table. Fix spelling errors.
2003-02-27 23:23:16 +00:00
*/
ahd_known_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
aic79xx.c: Include read streaming in the PPR flags we display in diagnostics. In ahd_reset(), set the known mode after our initial pause prior to setting the mode. We can't just set the mode directly because the current mode, after the pause, is most likely unknown and setting the mode when the saved mode is unknown will trigger an assertion in the mode debug code. Complete an audit for SCB RAM reads. These reads must be performed via the special ahd_in?_scbram() methods so we can perform a Rev A. PCI-X workaround. Remove a superfluous mode save operation that was performed just prior to a call to ahd_clear_critical_section(). The saved mode was never restored and wouldn't have been valid anyway since the mode could change while single stepping out of a critical section. aic79xx.h: Add new BUG definition AHD_PCIX_SCBRAM_RD_BUG. aic79xx_inline.h: Update ahd_inb_scbram routine to check for AHD_PCIX_SCBRAM_RD_BUG and only apply the workaround if this bug is active. The old code applied the workaround in all cases. aic79xx_pci.c: Set AHD_PCIX_SCBRAM_RD_BUG for the A4. Remove an attempted saved_modes call in ahd_pci_test_register_access(). Saving the modes can only occur when we are paused, but the call was happening before the chip was known to be paused. Restoring the modes doesn't make sense either since the code makes no assumptions about the state of the sequencer until the first time the mode is set by the driver. This happens after the registers are successfully mapped.
2003-03-06 23:58:34 +00:00
ahd_outb(ahd, MODE_PTR,
ahd_build_mode_state(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI));
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*
* Restore SXFRCTL1.
*
* We must always initialize STPWEN to 1 before we
* restore the saved values. STPWEN is initialized
* to a tri-state condition which can only be cleared
* by turning it on.
*/
ahd_outb(ahd, SXFRCTL1, sxfrctl1|STPWEN);
ahd_outb(ahd, SXFRCTL1, sxfrctl1);
aic79xx.c: Clear the LQICRC_NLQ status should it pop up after we have already handled the SCSIPERR. During some streaming operations this status can be delayed until the stream ends. Without this change, the driver would complain about a "Missing case in ahd_handle_scsiint". In the LQOBUSFREE handler... Don't return the LQOMGR back to the idle state until after we have cleaned up ENSELO and any status related to this selection. The last thing we need is the LQO manager starting another select-out before we have updated the execution queue. It is not clear whether the LQOMGR would, or would not start a new selection early. Make sure ENSELO is off prior to clearing SELDO by flushing device writes. Move assignment of the next target SCB pointer inside of an if to make the code clearer. The effect is the same. Dump card state in both "Unexpected PKT busfree" paths. In ahd_reset(), set the chip to SCSI mode before reading SXFRCTL1. That register only exists in the SCSI mode. Also set the mode explicitly to the SCSI mode after chip reset due to paranoia. Re-arrange code so that SXFRCTL1 is restored as quickly after the chip reset as possible. S/G structurs must be 8byte aligned. Make this official by saying so in our DMA tag. Disable CIO bus stretch on MDFFSTAT if SHVALID is about to come true. This can cause a CIO bus lockup if a PCI or PCI-X error occurs while the stretch is occurring - the host cannot service the PCI-X error since the CIO bus is locked out and SHVALID will never resolve. The stretch was added in the Rev B to simplify the wait for SHVALID to resolve, but the code to do this in the open source sequencer is so simple it was never removed. Consistently use MAX_OFFSET for the user max syncrate set from non-volatile storage. This ensures that the offset does not conflict with AH?_OFFSET_UNKNOWN. Have ahd_pause_and_flushwork set the mode to ensure that it has access to the registers it checks. Also modify the checking of intstat so that the check against 0xFF can actually succeed if the INT_PEND mask is something other than 0xFF. Although there are no cardbus U320 controllers, this check may be needed to recover from a hot-plug PCI removal that occurs without informing the driver. Fix a typo. sg_prefetch_cnt -> sg_prefetch_align. This fixes an infinite loop at card initialization if the cacheline size is 0. aic79xx.h: Add AHD_EARLY_REQ_BUG bug flag. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. Change AH?_OFFSET_UNKNOWN to 0xFF. This is a value that the curr->offset can never be, unlike '0' which we previously used. This fixes code that only checks for a non-zero offset to determine if a sync negotiation is required since it will fire in the unknown case even if the goal is async. aic79xx.reg: Add comments for LQISTAT bits indicating their names in the 7902 data book. We use slightly different and more descriptive names in the firmware. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. aic79xx.seq: Update comments regarding rundown of the GSFIFO to reflect reality. Fix spelling errors. Since we use an 8byte address and 1 byte length, shorten the size of a block move for the legacy DMA'ed CDB case from 11 to 9 bytes. Remove code that, assuming the abort pending feature worked, would set MK_MESSAGE in the SCB's control byte on completion to catch invalid reselections. Since we don't see interrupts for completed selections, this status update could occur prior to us noticing the SELDO. The "select-out" queue logic will get confused by the MK_MESSAGE bit being set as this is used to catch packatized connections where we select-out with ATN. Since the abort pending feature doesn't work on any released controllers yet, this code was never executed. Add support for the AHD_EARLY_REQ_BUG. Don't ignore persistent REQ assertions just because they were asserted within the bus settle delay window. This allows us to tolerate devices like the GEM318 that violate the SCSI spec. Remove unintentional settnig of SG_CACHE_AVAIL. Writing this bit should have no effect, but who knows... On the Rev A, we must wait for HDMAENACK before loading additional segments to avoid clobbering the address of the first segment in the S/G FIFO. This resolves data-corruption issues with certain IBM (now Hitachi) and Fujitsu U320 drives. Rearrange calc_residual to avoid an extra jmp instruction. On RevA Silicon, if the target returns us to data-out after we have already trained for data-out, it is possible for us to transition the free running clock to data-valid before the required 100ns P1 setup time (8 P1 assertions in fast-160 mode). This will only happen if this L-Q is a continuation of a data transfer for which we have already prefetched data into our FIFO (LQ/Data followed by LQ/Data for the same write transaction). This can cause some target implementations to miss the first few data transfers on the bus. We detect this situation by noticing that this is the first data transfer after an LQ (LQIWORKONLQ true), that the data transfer is a continuation of a transfer already setup in our FIFO (SAVEPTRS interrupt), and that the transaction is a write (DIRECTION set in DFCNTRL). The delay is performed by disabling SCSIEN until we see the first REQ from the target. Only compile in snapshot savepointers handler for RevA silicon where it is enabled. Handle the cfg4icmd packetized interrupt. We just need to load the address and count, start the DMA, and CLRCHN once the transfer is complete. Fix an oversight in the overrun handler for packetized status operations. We need to wait for either CTXTDONE or an overrun when checking for an overrun. The previous code did not wait and thus could decide that no overrun had occurred even though an overrun will occur on the next data-valid req. Add some comment to this section for clarity. Use LAST_SEG_DONE instead of LASTSDONE for testing transfer completion in the packetized status case. LASTSDONE may come up more quickly since it only records completion on the SCSI side, but since LAST_SEG_DONE is used everywhere else (and needs to be), this is less confusing. Add a missing invalidation of the longjmp address in the non-pack handler. This code needs additional review. aic79xx_inline.h: Fix spelling error. aic79xx_osm.c: Set the cdb length for CDBs dma'ed from host memory. Add a comment indicating that, should CAM start supporting cdbs larger than 16bytes, the driver could store the CDB in the status buffer. aic79xx_pci.c: Add a table entry for the 39320A. Added a missing comma to an error string table. Fix spelling errors.
2003-02-27 23:23:16 +00:00
/* Determine chip configuration */
ahd->features &= ~AHD_WIDE;
if ((ahd_inb(ahd, SBLKCTL) & SELWIDE) != 0)
ahd->features |= AHD_WIDE;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*
* If a recovery action has forced a chip reset,
aic79xx.c: Clear the LQICRC_NLQ status should it pop up after we have already handled the SCSIPERR. During some streaming operations this status can be delayed until the stream ends. Without this change, the driver would complain about a "Missing case in ahd_handle_scsiint". In the LQOBUSFREE handler... Don't return the LQOMGR back to the idle state until after we have cleaned up ENSELO and any status related to this selection. The last thing we need is the LQO manager starting another select-out before we have updated the execution queue. It is not clear whether the LQOMGR would, or would not start a new selection early. Make sure ENSELO is off prior to clearing SELDO by flushing device writes. Move assignment of the next target SCB pointer inside of an if to make the code clearer. The effect is the same. Dump card state in both "Unexpected PKT busfree" paths. In ahd_reset(), set the chip to SCSI mode before reading SXFRCTL1. That register only exists in the SCSI mode. Also set the mode explicitly to the SCSI mode after chip reset due to paranoia. Re-arrange code so that SXFRCTL1 is restored as quickly after the chip reset as possible. S/G structurs must be 8byte aligned. Make this official by saying so in our DMA tag. Disable CIO bus stretch on MDFFSTAT if SHVALID is about to come true. This can cause a CIO bus lockup if a PCI or PCI-X error occurs while the stretch is occurring - the host cannot service the PCI-X error since the CIO bus is locked out and SHVALID will never resolve. The stretch was added in the Rev B to simplify the wait for SHVALID to resolve, but the code to do this in the open source sequencer is so simple it was never removed. Consistently use MAX_OFFSET for the user max syncrate set from non-volatile storage. This ensures that the offset does not conflict with AH?_OFFSET_UNKNOWN. Have ahd_pause_and_flushwork set the mode to ensure that it has access to the registers it checks. Also modify the checking of intstat so that the check against 0xFF can actually succeed if the INT_PEND mask is something other than 0xFF. Although there are no cardbus U320 controllers, this check may be needed to recover from a hot-plug PCI removal that occurs without informing the driver. Fix a typo. sg_prefetch_cnt -> sg_prefetch_align. This fixes an infinite loop at card initialization if the cacheline size is 0. aic79xx.h: Add AHD_EARLY_REQ_BUG bug flag. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. Change AH?_OFFSET_UNKNOWN to 0xFF. This is a value that the curr->offset can never be, unlike '0' which we previously used. This fixes code that only checks for a non-zero offset to determine if a sync negotiation is required since it will fire in the unknown case even if the goal is async. aic79xx.reg: Add comments for LQISTAT bits indicating their names in the 7902 data book. We use slightly different and more descriptive names in the firmware. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. aic79xx.seq: Update comments regarding rundown of the GSFIFO to reflect reality. Fix spelling errors. Since we use an 8byte address and 1 byte length, shorten the size of a block move for the legacy DMA'ed CDB case from 11 to 9 bytes. Remove code that, assuming the abort pending feature worked, would set MK_MESSAGE in the SCB's control byte on completion to catch invalid reselections. Since we don't see interrupts for completed selections, this status update could occur prior to us noticing the SELDO. The "select-out" queue logic will get confused by the MK_MESSAGE bit being set as this is used to catch packatized connections where we select-out with ATN. Since the abort pending feature doesn't work on any released controllers yet, this code was never executed. Add support for the AHD_EARLY_REQ_BUG. Don't ignore persistent REQ assertions just because they were asserted within the bus settle delay window. This allows us to tolerate devices like the GEM318 that violate the SCSI spec. Remove unintentional settnig of SG_CACHE_AVAIL. Writing this bit should have no effect, but who knows... On the Rev A, we must wait for HDMAENACK before loading additional segments to avoid clobbering the address of the first segment in the S/G FIFO. This resolves data-corruption issues with certain IBM (now Hitachi) and Fujitsu U320 drives. Rearrange calc_residual to avoid an extra jmp instruction. On RevA Silicon, if the target returns us to data-out after we have already trained for data-out, it is possible for us to transition the free running clock to data-valid before the required 100ns P1 setup time (8 P1 assertions in fast-160 mode). This will only happen if this L-Q is a continuation of a data transfer for which we have already prefetched data into our FIFO (LQ/Data followed by LQ/Data for the same write transaction). This can cause some target implementations to miss the first few data transfers on the bus. We detect this situation by noticing that this is the first data transfer after an LQ (LQIWORKONLQ true), that the data transfer is a continuation of a transfer already setup in our FIFO (SAVEPTRS interrupt), and that the transaction is a write (DIRECTION set in DFCNTRL). The delay is performed by disabling SCSIEN until we see the first REQ from the target. Only compile in snapshot savepointers handler for RevA silicon where it is enabled. Handle the cfg4icmd packetized interrupt. We just need to load the address and count, start the DMA, and CLRCHN once the transfer is complete. Fix an oversight in the overrun handler for packetized status operations. We need to wait for either CTXTDONE or an overrun when checking for an overrun. The previous code did not wait and thus could decide that no overrun had occurred even though an overrun will occur on the next data-valid req. Add some comment to this section for clarity. Use LAST_SEG_DONE instead of LASTSDONE for testing transfer completion in the packetized status case. LASTSDONE may come up more quickly since it only records completion on the SCSI side, but since LAST_SEG_DONE is used everywhere else (and needs to be), this is less confusing. Add a missing invalidation of the longjmp address in the non-pack handler. This code needs additional review. aic79xx_inline.h: Fix spelling error. aic79xx_osm.c: Set the cdb length for CDBs dma'ed from host memory. Add a comment indicating that, should CAM start supporting cdbs larger than 16bytes, the driver could store the CDB in the status buffer. aic79xx_pci.c: Add a table entry for the 39320A. Added a missing comma to an error string table. Fix spelling errors.
2003-02-27 23:23:16 +00:00
* re-initialize the chip to our liking.
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
*/
aic7770.c: aic79xx.c: aic79xx.h: aic79xx_pci.c: aic7xxx.c: aic7xxx.h: aic7xxx_pci.c: Switch ah?_reset() to take an additional "reinit" argument. Use this instead of init_level to determin if the chip should be fully reinitialized after a chip reset. This is required so that ah?_shutdown() can reset the chip without side-effects. aic79xx.c: Implement ahd_suspend() and ahd_resume(). aic7xxx.c: Change ahc_loadseq() to *not* restart the sequencer. This brings the loadseq behavior in line with that of the 7902 driver and also simplifies the init routine. Correct the resume routine to enable interrupts and restart the sequencer.
2003-06-06 23:48:19 +00:00
if (reinit != 0)
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_chip_init(ahd);
return (0);
}
/*
* Determine the number of SCBs available on the controller
*/
int
ahd_probe_scbs(struct ahd_softc *ahd) {
int i;
AHD_ASSERT_MODES(ahd, ~(AHD_MODE_UNKNOWN_MSK|AHD_MODE_CFG_MSK),
~(AHD_MODE_UNKNOWN_MSK|AHD_MODE_CFG_MSK));
for (i = 0; i < AHD_SCB_MAX; i++) {
int j;
ahd_set_scbptr(ahd, i);
ahd_outw(ahd, SCB_BASE, i);
for (j = 2; j < 64; j++)
ahd_outb(ahd, SCB_BASE+j, 0);
/* Start out life as unallocated (needing an abort) */
ahd_outb(ahd, SCB_CONTROL, MK_MESSAGE);
if (ahd_inw_scbram(ahd, SCB_BASE) != i)
break;
ahd_set_scbptr(ahd, 0);
if (ahd_inw_scbram(ahd, SCB_BASE) != 0)
break;
}
return (i);
}
static void
ahd_dmamap_cb(void *arg, bus_dma_segment_t *segs, int nseg, int error)
{
bus_addr_t *baddr;
baddr = (bus_addr_t *)arg;
*baddr = segs->ds_addr;
}
static void
ahd_initialize_hscbs(struct ahd_softc *ahd)
{
int i;
for (i = 0; i < ahd->scb_data.maxhscbs; i++) {
ahd_set_scbptr(ahd, i);
/* Clear the control byte. */
ahd_outb(ahd, SCB_CONTROL, 0);
/* Set the next pointer */
ahd_outw(ahd, SCB_NEXT, SCB_LIST_NULL);
}
}
static int
ahd_init_scbdata(struct ahd_softc *ahd)
{
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
struct scb_data *scb_data;
int i;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
scb_data = &ahd->scb_data;
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
TAILQ_INIT(&scb_data->free_scbs);
for (i = 0; i < AHD_NUM_TARGETS * AHD_NUM_LUNS_NONPKT; i++)
LIST_INIT(&scb_data->free_scb_lists[i]);
LIST_INIT(&scb_data->any_dev_free_scb_list);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
SLIST_INIT(&scb_data->hscb_maps);
SLIST_INIT(&scb_data->sg_maps);
SLIST_INIT(&scb_data->sense_maps);
/* Determine the number of hardware SCBs and initialize them */
scb_data->maxhscbs = ahd_probe_scbs(ahd);
if (scb_data->maxhscbs == 0) {
printf("%s: No SCB space found\n", ahd_name(ahd));
return (ENXIO);
}
ahd_initialize_hscbs(ahd);
/*
* Create our DMA tags. These tags define the kinds of device
* accessible memory allocations and memory mappings we will
* need to perform during normal operation.
*
* Unless we need to further restrict the allocation, we rely
* on the restrictions of the parent dmat, hence the common
* use of MAXADDR and MAXSIZE.
*/
/* DMA tag for our hardware scb structures */
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
if (aic_dma_tag_create(ahd, ahd->parent_dmat, /*alignment*/1,
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*boundary*/BUS_SPACE_MAXADDR_32BIT + 1,
/*lowaddr*/BUS_SPACE_MAXADDR_32BIT,
/*highaddr*/BUS_SPACE_MAXADDR,
/*filter*/NULL, /*filterarg*/NULL,
PAGE_SIZE, /*nsegments*/1,
/*maxsegsz*/BUS_SPACE_MAXSIZE_32BIT,
/*flags*/0, &scb_data->hscb_dmat) != 0) {
goto error_exit;
}
scb_data->init_level++;
/* DMA tag for our S/G structures. */
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
if (aic_dma_tag_create(ahd, ahd->parent_dmat, /*alignment*/8,
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*boundary*/BUS_SPACE_MAXADDR_32BIT + 1,
/*lowaddr*/BUS_SPACE_MAXADDR_32BIT,
/*highaddr*/BUS_SPACE_MAXADDR,
/*filter*/NULL, /*filterarg*/NULL,
ahd_sglist_allocsize(ahd), /*nsegments*/1,
/*maxsegsz*/BUS_SPACE_MAXSIZE_32BIT,
/*flags*/0, &scb_data->sg_dmat) != 0) {
goto error_exit;
}
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_MEMORY) != 0)
printf("%s: ahd_sglist_allocsize = 0x%x\n", ahd_name(ahd),
ahd_sglist_allocsize(ahd));
#endif
scb_data->init_level++;
/* DMA tag for our sense buffers. We allocate in page sized chunks */
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
if (aic_dma_tag_create(ahd, ahd->parent_dmat, /*alignment*/1,
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*boundary*/BUS_SPACE_MAXADDR_32BIT + 1,
/*lowaddr*/BUS_SPACE_MAXADDR_32BIT,
/*highaddr*/BUS_SPACE_MAXADDR,
/*filter*/NULL, /*filterarg*/NULL,
PAGE_SIZE, /*nsegments*/1,
/*maxsegsz*/BUS_SPACE_MAXSIZE_32BIT,
/*flags*/0, &scb_data->sense_dmat) != 0) {
goto error_exit;
}
scb_data->init_level++;
/* Perform initial CCB allocation */
ahd_alloc_scbs(ahd);
if (scb_data->numscbs == 0) {
printf("%s: ahd_init_scbdata - "
"Unable to allocate initial scbs\n",
ahd_name(ahd));
goto error_exit;
}
/*
* Note that we were successfull
*/
return (0);
error_exit:
return (ENOMEM);
}
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
static struct scb *
ahd_find_scb_by_tag(struct ahd_softc *ahd, u_int tag)
{
struct scb *scb;
/*
* Look on the pending list.
*/
LIST_FOREACH(scb, &ahd->pending_scbs, pending_links) {
if (SCB_GET_TAG(scb) == tag)
return (scb);
}
/*
* Then on all of the collision free lists.
*/
TAILQ_FOREACH(scb, &ahd->scb_data.free_scbs, links.tqe) {
struct scb *list_scb;
list_scb = scb;
do {
if (SCB_GET_TAG(list_scb) == tag)
return (list_scb);
list_scb = LIST_NEXT(list_scb, collision_links);
} while (list_scb);
}
/*
* And finally on the generic free list.
*/
LIST_FOREACH(scb, &ahd->scb_data.any_dev_free_scb_list, links.le) {
if (SCB_GET_TAG(scb) == tag)
return (scb);
}
return (NULL);
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
static void
ahd_fini_scbdata(struct ahd_softc *ahd)
{
struct scb_data *scb_data;
scb_data = &ahd->scb_data;
if (scb_data == NULL)
return;
switch (scb_data->init_level) {
default:
case 7:
{
struct map_node *sns_map;
while ((sns_map = SLIST_FIRST(&scb_data->sense_maps)) != NULL) {
SLIST_REMOVE_HEAD(&scb_data->sense_maps, links);
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_dmamap_unload(ahd, scb_data->sense_dmat,
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
sns_map->dmamap);
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_dmamem_free(ahd, scb_data->sense_dmat,
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
sns_map->vaddr, sns_map->dmamap);
free(sns_map, M_DEVBUF);
}
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_dma_tag_destroy(ahd, scb_data->sense_dmat);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/* FALLTHROUGH */
}
case 6:
{
struct map_node *sg_map;
while ((sg_map = SLIST_FIRST(&scb_data->sg_maps)) != NULL) {
SLIST_REMOVE_HEAD(&scb_data->sg_maps, links);
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_dmamap_unload(ahd, scb_data->sg_dmat,
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
sg_map->dmamap);
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_dmamem_free(ahd, scb_data->sg_dmat,
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
sg_map->vaddr, sg_map->dmamap);
free(sg_map, M_DEVBUF);
}
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_dma_tag_destroy(ahd, scb_data->sg_dmat);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/* FALLTHROUGH */
}
case 5:
{
struct map_node *hscb_map;
while ((hscb_map = SLIST_FIRST(&scb_data->hscb_maps)) != NULL) {
SLIST_REMOVE_HEAD(&scb_data->hscb_maps, links);
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_dmamap_unload(ahd, scb_data->hscb_dmat,
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
hscb_map->dmamap);
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_dmamem_free(ahd, scb_data->hscb_dmat,
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
hscb_map->vaddr, hscb_map->dmamap);
free(hscb_map, M_DEVBUF);
}
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_dma_tag_destroy(ahd, scb_data->hscb_dmat);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/* FALLTHROUGH */
}
case 4:
case 3:
case 2:
case 1:
case 0:
break;
}
}
/*
* DSP filter Bypass must be enabled until the first selection
* after a change in bus mode (Razor #491 and #493).
*/
static void
ahd_setup_iocell_workaround(struct ahd_softc *ahd)
{
ahd_mode_state saved_modes;
saved_modes = ahd_save_modes(ahd);
ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG);
ahd_outb(ahd, DSPDATACTL, ahd_inb(ahd, DSPDATACTL)
| BYPASSENAB | RCVROFFSTDIS | XMITOFFSTDIS);
ahd_outb(ahd, SIMODE0, ahd_inb(ahd, SIMODE0) | (ENSELDO|ENSELDI));
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_MISC) != 0)
printf("%s: Setting up iocell workaround\n", ahd_name(ahd));
#endif
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_restore_modes(ahd, saved_modes);
aic79xx.h: Add softc flag to indicate that we have seen at least one selection since the last bus reset or SE/LVD bus change. aic79xx.c: Fix a few style nits. In ahd_update_pending_scbs(), only touch card registers once we have found an SCB that needs to be updated. This removes lots of clutter from PCI traces taken of error recovery performed by the driver. Short circuit the first selection iocell workaround handler if we've run once since the last bus reset or iocell change. This also removes clutter from PCI traces. Note if completions are pending in the qoutfifo when we dump card state.
2003-06-28 04:45:25 +00:00
ahd->flags &= ~AHD_HAD_FIRST_SEL;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
static void
ahd_iocell_first_selection(struct ahd_softc *ahd)
{
ahd_mode_state saved_modes;
u_int sblkctl;
aic79xx.h: Add softc flag to indicate that we have seen at least one selection since the last bus reset or SE/LVD bus change. aic79xx.c: Fix a few style nits. In ahd_update_pending_scbs(), only touch card registers once we have found an SCB that needs to be updated. This removes lots of clutter from PCI traces taken of error recovery performed by the driver. Short circuit the first selection iocell workaround handler if we've run once since the last bus reset or iocell change. This also removes clutter from PCI traces. Note if completions are pending in the qoutfifo when we dump card state.
2003-06-28 04:45:25 +00:00
if ((ahd->flags & AHD_HAD_FIRST_SEL) != 0)
return;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
saved_modes = ahd_save_modes(ahd);
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
sblkctl = ahd_inb(ahd, SBLKCTL);
ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG);
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_MISC) != 0)
printf("%s: iocell first selection\n", ahd_name(ahd));
#endif
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if ((sblkctl & ENAB40) != 0) {
ahd_outb(ahd, DSPDATACTL,
ahd_inb(ahd, DSPDATACTL) & ~BYPASSENAB);
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_MISC) != 0)
printf("%s: BYPASS now disabled\n", ahd_name(ahd));
#endif
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
ahd_outb(ahd, SIMODE0, ahd_inb(ahd, SIMODE0) & ~(ENSELDO|ENSELDI));
ahd_outb(ahd, CLRINT, CLRSCSIINT);
ahd_restore_modes(ahd, saved_modes);
aic79xx.h: Add softc flag to indicate that we have seen at least one selection since the last bus reset or SE/LVD bus change. aic79xx.c: Fix a few style nits. In ahd_update_pending_scbs(), only touch card registers once we have found an SCB that needs to be updated. This removes lots of clutter from PCI traces taken of error recovery performed by the driver. Short circuit the first selection iocell workaround handler if we've run once since the last bus reset or iocell change. This also removes clutter from PCI traces. Note if completions are pending in the qoutfifo when we dump card state.
2003-06-28 04:45:25 +00:00
ahd->flags |= AHD_HAD_FIRST_SEL;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
/*************************** SCB Management ***********************************/
static void
ahd_add_col_list(struct ahd_softc *ahd, struct scb *scb, u_int col_idx)
{
struct scb_list *free_list;
struct scb_tailq *free_tailq;
struct scb *first_scb;
scb->flags |= SCB_ON_COL_LIST;
AHD_SET_SCB_COL_IDX(scb, col_idx);
free_list = &ahd->scb_data.free_scb_lists[col_idx];
free_tailq = &ahd->scb_data.free_scbs;
first_scb = LIST_FIRST(free_list);
if (first_scb != NULL) {
LIST_INSERT_AFTER(first_scb, scb, collision_links);
} else {
LIST_INSERT_HEAD(free_list, scb, collision_links);
TAILQ_INSERT_TAIL(free_tailq, scb, links.tqe);
}
}
static void
ahd_rem_col_list(struct ahd_softc *ahd, struct scb *scb)
{
struct scb_list *free_list;
struct scb_tailq *free_tailq;
struct scb *first_scb;
u_int col_idx;
scb->flags &= ~SCB_ON_COL_LIST;
col_idx = AHD_GET_SCB_COL_IDX(ahd, scb);
free_list = &ahd->scb_data.free_scb_lists[col_idx];
free_tailq = &ahd->scb_data.free_scbs;
first_scb = LIST_FIRST(free_list);
if (first_scb == scb) {
struct scb *next_scb;
/*
* Maintain order in the collision free
* lists for fairness if this device has
* other colliding tags active.
*/
next_scb = LIST_NEXT(scb, collision_links);
if (next_scb != NULL) {
TAILQ_INSERT_AFTER(free_tailq, scb,
next_scb, links.tqe);
}
TAILQ_REMOVE(free_tailq, scb, links.tqe);
}
LIST_REMOVE(scb, collision_links);
}
/*
* Get a free scb. If there are none, see if we can allocate a new SCB.
*/
struct scb *
ahd_get_scb(struct ahd_softc *ahd, u_int col_idx)
{
struct scb *scb;
int tries;
tries = 0;
look_again:
TAILQ_FOREACH(scb, &ahd->scb_data.free_scbs, links.tqe) {
if (AHD_GET_SCB_COL_IDX(ahd, scb) != col_idx) {
ahd_rem_col_list(ahd, scb);
goto found;
}
}
if ((scb = LIST_FIRST(&ahd->scb_data.any_dev_free_scb_list)) == NULL) {
if (tries++ != 0)
return (NULL);
ahd_alloc_scbs(ahd);
goto look_again;
}
LIST_REMOVE(scb, links.le);
if (col_idx != AHD_NEVER_COL_IDX
&& (scb->col_scb != NULL)
&& (scb->col_scb->flags & SCB_ACTIVE) == 0) {
LIST_REMOVE(scb->col_scb, links.le);
ahd_add_col_list(ahd, scb->col_scb, col_idx);
}
found:
scb->flags |= SCB_ACTIVE;
return (scb);
}
/*
* Return an SCB resource to the free list.
*/
void
ahd_free_scb(struct ahd_softc *ahd, struct scb *scb)
{
/* Clean up for the next user */
scb->flags = SCB_FLAG_NONE;
scb->hscb->control = 0;
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
ahd->scb_data.scbindex[SCB_GET_TAG(scb)] = NULL;
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
if (scb->col_scb == NULL) {
/*
* No collision possible. Just free normally.
*/
LIST_INSERT_HEAD(&ahd->scb_data.any_dev_free_scb_list,
scb, links.le);
} else if ((scb->col_scb->flags & SCB_ON_COL_LIST) != 0) {
/*
* The SCB we might have collided with is on
* a free collision list. Put both SCBs on
* the generic list.
*/
ahd_rem_col_list(ahd, scb->col_scb);
LIST_INSERT_HEAD(&ahd->scb_data.any_dev_free_scb_list,
scb, links.le);
LIST_INSERT_HEAD(&ahd->scb_data.any_dev_free_scb_list,
scb->col_scb, links.le);
} else if ((scb->col_scb->flags
& (SCB_PACKETIZED|SCB_ACTIVE)) == SCB_ACTIVE
&& (scb->col_scb->hscb->control & TAG_ENB) != 0) {
/*
* The SCB we might collide with on the next allocation
* is still active in a non-packetized, tagged, context.
* Put us on the SCB collision list.
*/
ahd_add_col_list(ahd, scb,
AHD_GET_SCB_COL_IDX(ahd, scb->col_scb));
} else {
/*
* The SCB we might collide with on the next allocation
* is either active in a packetized context, or free.
* Since we can't collide, put this SCB on the generic
* free list.
*/
LIST_INSERT_HEAD(&ahd->scb_data.any_dev_free_scb_list,
scb, links.le);
}
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_platform_scb_free(ahd, scb);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
void
ahd_alloc_scbs(struct ahd_softc *ahd)
{
struct scb_data *scb_data;
struct scb *next_scb;
struct hardware_scb *hscb;
struct map_node *hscb_map;
struct map_node *sg_map;
struct map_node *sense_map;
uint8_t *segs;
uint8_t *sense_data;
bus_addr_t hscb_busaddr;
bus_addr_t sg_busaddr;
bus_addr_t sense_busaddr;
int newcount;
int i;
scb_data = &ahd->scb_data;
if (scb_data->numscbs >= AHD_SCB_MAX_ALLOC)
/* Can't allocate any more */
return;
if (scb_data->scbs_left != 0) {
int offset;
offset = (PAGE_SIZE / sizeof(*hscb)) - scb_data->scbs_left;
hscb_map = SLIST_FIRST(&scb_data->hscb_maps);
hscb = &((struct hardware_scb *)hscb_map->vaddr)[offset];
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
hscb_busaddr = hscb_map->busaddr + (offset * sizeof(*hscb));
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
} else {
hscb_map = malloc(sizeof(*hscb_map), M_DEVBUF, M_NOWAIT);
if (hscb_map == NULL)
return;
/* Allocate the next batch of hardware SCBs */
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
if (aic_dmamem_alloc(ahd, scb_data->hscb_dmat,
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
(void **)&hscb_map->vaddr,
BUS_DMA_NOWAIT, &hscb_map->dmamap) != 0) {
free(hscb_map, M_DEVBUF);
return;
}
SLIST_INSERT_HEAD(&scb_data->hscb_maps, hscb_map, links);
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_dmamap_load(ahd, scb_data->hscb_dmat, hscb_map->dmamap,
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
hscb_map->vaddr, PAGE_SIZE, ahd_dmamap_cb,
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
&hscb_map->busaddr, /*flags*/0);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
hscb = (struct hardware_scb *)hscb_map->vaddr;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
hscb_busaddr = hscb_map->busaddr;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
scb_data->scbs_left = PAGE_SIZE / sizeof(*hscb);
}
if (scb_data->sgs_left != 0) {
int offset;
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
offset = ((ahd_sglist_allocsize(ahd) / ahd_sglist_size(ahd))
- scb_data->sgs_left) * ahd_sglist_size(ahd);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
sg_map = SLIST_FIRST(&scb_data->sg_maps);
segs = sg_map->vaddr + offset;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
sg_busaddr = sg_map->busaddr + offset;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
} else {
sg_map = malloc(sizeof(*sg_map), M_DEVBUF, M_NOWAIT);
if (sg_map == NULL)
return;
/* Allocate the next batch of S/G lists */
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
if (aic_dmamem_alloc(ahd, scb_data->sg_dmat,
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
(void **)&sg_map->vaddr,
BUS_DMA_NOWAIT, &sg_map->dmamap) != 0) {
free(sg_map, M_DEVBUF);
return;
}
SLIST_INSERT_HEAD(&scb_data->sg_maps, sg_map, links);
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_dmamap_load(ahd, scb_data->sg_dmat, sg_map->dmamap,
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
sg_map->vaddr, ahd_sglist_allocsize(ahd),
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
ahd_dmamap_cb, &sg_map->busaddr, /*flags*/0);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
segs = sg_map->vaddr;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
sg_busaddr = sg_map->busaddr;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
scb_data->sgs_left =
ahd_sglist_allocsize(ahd) / ahd_sglist_size(ahd);
#ifdef AHD_DEBUG
if (ahd_debug & AHD_SHOW_MEMORY)
printf("Mapped SG data\n");
#endif
}
if (scb_data->sense_left != 0) {
int offset;
offset = PAGE_SIZE - (AHD_SENSE_BUFSIZE * scb_data->sense_left);
sense_map = SLIST_FIRST(&scb_data->sense_maps);
sense_data = sense_map->vaddr + offset;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
sense_busaddr = sense_map->busaddr + offset;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
} else {
sense_map = malloc(sizeof(*sense_map), M_DEVBUF, M_NOWAIT);
if (sense_map == NULL)
return;
/* Allocate the next batch of sense buffers */
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
if (aic_dmamem_alloc(ahd, scb_data->sense_dmat,
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
(void **)&sense_map->vaddr,
BUS_DMA_NOWAIT, &sense_map->dmamap) != 0) {
free(sense_map, M_DEVBUF);
return;
}
SLIST_INSERT_HEAD(&scb_data->sense_maps, sense_map, links);
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_dmamap_load(ahd, scb_data->sense_dmat, sense_map->dmamap,
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
sense_map->vaddr, PAGE_SIZE, ahd_dmamap_cb,
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
&sense_map->busaddr, /*flags*/0);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
sense_data = sense_map->vaddr;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
sense_busaddr = sense_map->busaddr;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
scb_data->sense_left = PAGE_SIZE / AHD_SENSE_BUFSIZE;
#ifdef AHD_DEBUG
if (ahd_debug & AHD_SHOW_MEMORY)
printf("Mapped sense data\n");
#endif
}
newcount = MIN(scb_data->sense_left, scb_data->scbs_left);
newcount = MIN(newcount, scb_data->sgs_left);
newcount = MIN(newcount, (AHD_SCB_MAX_ALLOC - scb_data->numscbs));
scb_data->sense_left -= newcount;
scb_data->scbs_left -= newcount;
scb_data->sgs_left -= newcount;
for (i = 0; i < newcount; i++) {
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
u_int col_tag;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
struct scb_platform_data *pdata;
#ifndef __linux__
int error;
#endif
next_scb = (struct scb *)malloc(sizeof(*next_scb),
M_DEVBUF, M_NOWAIT);
if (next_scb == NULL)
break;
pdata = (struct scb_platform_data *)malloc(sizeof(*pdata),
M_DEVBUF, M_NOWAIT);
if (pdata == NULL) {
free(next_scb, M_DEVBUF);
break;
}
next_scb->platform_data = pdata;
next_scb->hscb_map = hscb_map;
next_scb->sg_map = sg_map;
next_scb->sense_map = sense_map;
next_scb->sg_list = segs;
next_scb->sense_data = sense_data;
next_scb->sense_busaddr = sense_busaddr;
Change hadling of the Rev. A packetized lun output bug to be more efficient by having the sequencer copy the single byte of valid lun data into the long lun field. aic79xx.c: Memset our hardware SCB to 0 so that untouched fields don't confuse diagnostic output. With the old method for handling the Rev A bug, if the long lun field was not 0, this could result in bogus lun information being sent to drives. Use the same SCB transfer size for all chip types now that the long lun is not DMA'ed to the chip. aic79xx.seq: Add code to copy lun information for Rev.A hardware. aic79xx_inline.h: Remove host update of the long_lun field on every packetized command.
2003-05-26 21:18:48 +00:00
memset(hscb, 0, sizeof(*hscb));
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
next_scb->hscb = hscb;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
hscb->hscb_busaddr = aic_htole32(hscb_busaddr);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*
* The sequencer always starts with the second entry.
* The first entry is embedded in the scb.
*/
next_scb->sg_list_busaddr = sg_busaddr;
if ((ahd->flags & AHD_64BIT_ADDRESSING) != 0)
next_scb->sg_list_busaddr
+= sizeof(struct ahd_dma64_seg);
else
next_scb->sg_list_busaddr += sizeof(struct ahd_dma_seg);
next_scb->ahd_softc = ahd;
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
next_scb->flags = SCB_FLAG_NONE;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
#ifndef __linux__
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
error = aic_dmamap_create(ahd, ahd->buffer_dmat, /*flags*/0,
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
&next_scb->dmamap);
if (error != 0) {
free(next_scb, M_DEVBUF);
free(pdata, M_DEVBUF);
break;
}
#endif
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
next_scb->hscb->tag = aic_htole16(scb_data->numscbs);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
col_tag = scb_data->numscbs ^ 0x100;
next_scb->col_scb = ahd_find_scb_by_tag(ahd, col_tag);
if (next_scb->col_scb != NULL)
next_scb->col_scb->col_scb = next_scb;
ahd_free_scb(ahd, next_scb);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
hscb++;
hscb_busaddr += sizeof(*hscb);
segs += ahd_sglist_size(ahd);
sg_busaddr += ahd_sglist_size(ahd);
sense_data += AHD_SENSE_BUFSIZE;
sense_busaddr += AHD_SENSE_BUFSIZE;
scb_data->numscbs++;
}
}
void
ahd_controller_info(struct ahd_softc *ahd, char *buf)
{
const char *speed;
const char *type;
int len;
len = sprintf(buf, "%s: ", ahd_chip_names[ahd->chip & AHD_CHIPID_MASK]);
buf += len;
speed = "Ultra320 ";
if ((ahd->features & AHD_WIDE) != 0) {
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
type = "Wide ";
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
} else {
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
type = "Single ";
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
len = sprintf(buf, "%s%sChannel %c, SCSI Id=%d, ",
speed, type, ahd->channel, ahd->our_id);
buf += len;
sprintf(buf, "%s, %d SCBs", ahd->bus_description,
ahd->scb_data.maxhscbs);
}
static const char *channel_strings[] = {
"Primary Low",
"Primary High",
"Secondary Low",
"Secondary High"
};
static const char *termstat_strings[] = {
"Terminated Correctly",
"Over Terminated",
"Under Terminated",
"Not Configured"
};
/*
* Start the board, ready for normal operation
*/
int
ahd_init(struct ahd_softc *ahd)
{
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
uint8_t *next_vaddr;
bus_addr_t next_baddr;
size_t driver_data_size;
int i;
int error;
u_int warn_user;
uint8_t current_sensing;
uint8_t fstat;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
AHD_ASSERT_MODES(ahd, AHD_MODE_SCSI_MSK, AHD_MODE_SCSI_MSK);
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
ahd->stack_size = ahd_probe_stack_size(ahd);
ahd->saved_stack = malloc(ahd->stack_size * sizeof(uint16_t),
M_DEVBUF, M_NOWAIT);
if (ahd->saved_stack == NULL)
return (ENOMEM);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*
* Verify that the compiler hasn't over-agressively
* padded important structures.
*/
if (sizeof(struct hardware_scb) != 64)
panic("Hardware SCB size is incorrect");
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_DEBUG_SEQUENCER) != 0)
ahd->flags |= AHD_SEQUENCER_DEBUG;
#endif
/*
* Default to allowing initiator operations.
*/
ahd->flags |= AHD_INITIATORROLE;
/*
* Only allow target mode features if this unit has them enabled.
*/
if ((AHD_TMODE_ENABLE & (0x1 << ahd->unit)) == 0)
ahd->features &= ~AHD_TARGETMODE;
#ifndef __linux__
/* DMA tag for mapping buffers into device visible space. */
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
if (aic_dma_tag_create(ahd, ahd->parent_dmat, /*alignment*/1,
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*boundary*/BUS_SPACE_MAXADDR_32BIT + 1,
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
/*lowaddr*/ahd->flags & AHD_39BIT_ADDRESSING
? (bus_addr_t)0x7FFFFFFFFFULL
: BUS_SPACE_MAXADDR_32BIT,
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*highaddr*/BUS_SPACE_MAXADDR,
/*filter*/NULL, /*filterarg*/NULL,
Convert the use of MAXBSIZE in the dma tag to more appropriate values. Use BUS_SPACE_MAXSIZE_32BIT for the parent dma tags, and (NSEGS - 1) * PAGE_SIZE for the data buffer tags. FreeBSD/sparc64 is more strict about checking these values that other arches.
2002-12-31 04:22:36 +00:00
/*maxsize*/(AHD_NSEG - 1) * PAGE_SIZE,
/*nsegments*/AHD_NSEG,
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*maxsegsz*/AHD_MAXTRANSFER_SIZE,
/*flags*/BUS_DMA_ALLOCNOW,
&ahd->buffer_dmat) != 0) {
return (ENOMEM);
}
#endif
ahd->init_level++;
/*
* DMA tag for our command fifos and other data in system memory
* the card's sequencer must be able to access. For initiator
* roles, we need to allocate space for the qoutfifo. When providing
* for the target mode role, we must additionally provide space for
* the incoming target command fifo.
*/
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
driver_data_size = AHD_SCB_MAX * sizeof(uint16_t)
+ sizeof(struct hardware_scb);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if ((ahd->features & AHD_TARGETMODE) != 0)
driver_data_size += AHD_TMODE_CMDS * sizeof(struct target_cmd);
if ((ahd->bugs & AHD_PKT_BITBUCKET_BUG) != 0)
driver_data_size += PKT_OVERRUN_BUFSIZE;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
if (aic_dma_tag_create(ahd, ahd->parent_dmat, /*alignment*/1,
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*boundary*/BUS_SPACE_MAXADDR_32BIT + 1,
/*lowaddr*/BUS_SPACE_MAXADDR_32BIT,
/*highaddr*/BUS_SPACE_MAXADDR,
/*filter*/NULL, /*filterarg*/NULL,
driver_data_size,
/*nsegments*/1,
/*maxsegsz*/BUS_SPACE_MAXSIZE_32BIT,
/*flags*/0, &ahd->shared_data_dmat) != 0) {
return (ENOMEM);
}
ahd->init_level++;
/* Allocation of driver data */
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
if (aic_dmamem_alloc(ahd, ahd->shared_data_dmat,
(void **)&ahd->shared_data_map.vaddr,
BUS_DMA_NOWAIT,
&ahd->shared_data_map.dmamap) != 0) {
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
return (ENOMEM);
}
ahd->init_level++;
/* And permanently map it in */
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_dmamap_load(ahd, ahd->shared_data_dmat, ahd->shared_data_map.dmamap,
ahd->shared_data_map.vaddr, driver_data_size,
ahd_dmamap_cb, &ahd->shared_data_map.busaddr,
/*flags*/0);
ahd->qoutfifo = (uint16_t *)ahd->shared_data_map.vaddr;
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
next_vaddr = (uint8_t *)&ahd->qoutfifo[AHD_QOUT_SIZE];
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
next_baddr = ahd->shared_data_map.busaddr
+ AHD_QOUT_SIZE*sizeof(uint16_t);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if ((ahd->features & AHD_TARGETMODE) != 0) {
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
ahd->targetcmds = (struct target_cmd *)next_vaddr;
next_vaddr += AHD_TMODE_CMDS * sizeof(struct target_cmd);
next_baddr += AHD_TMODE_CMDS * sizeof(struct target_cmd);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
if ((ahd->bugs & AHD_PKT_BITBUCKET_BUG) != 0) {
ahd->overrun_buf = next_vaddr;
next_vaddr += PKT_OVERRUN_BUFSIZE;
next_baddr += PKT_OVERRUN_BUFSIZE;
}
/*
* We need one SCB to serve as the "next SCB". Since the
* tag identifier in this SCB will never be used, there is
* no point in using a valid HSCB tag from an SCB pulled from
* the standard free pool. So, we allocate this "sentinel"
* specially from the DMA safe memory chunk used for the QOUTFIFO.
*/
ahd->next_queued_hscb = (struct hardware_scb *)next_vaddr;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
ahd->next_queued_hscb_map = &ahd->shared_data_map;
ahd->next_queued_hscb->hscb_busaddr = aic_htole32(next_baddr);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd->init_level++;
/* Allocate SCB data now that buffer_dmat is initialized */
if (ahd_init_scbdata(ahd) != 0)
return (ENOMEM);
if ((ahd->flags & AHD_INITIATORROLE) == 0)
ahd->flags &= ~AHD_RESET_BUS_A;
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
/*
* Before committing these settings to the chip, give
* the OSM one last chance to modify our configuration.
*/
ahd_platform_init(ahd);
/* Bring up the chip. */
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_chip_init(ahd);
AHD_ASSERT_MODES(ahd, AHD_MODE_SCSI_MSK, AHD_MODE_SCSI_MSK);
if ((ahd->flags & AHD_CURRENT_SENSING) == 0)
goto init_done;
/*
* Verify termination based on current draw and
* warn user if the bus is over/under terminated.
*/
error = ahd_write_flexport(ahd, FLXADDR_ROMSTAT_CURSENSECTL,
CURSENSE_ENB);
if (error != 0) {
printf("%s: current sensing timeout 1\n", ahd_name(ahd));
goto init_done;
}
for (i = 20, fstat = FLX_FSTAT_BUSY;
(fstat & FLX_FSTAT_BUSY) != 0 && i; i--) {
error = ahd_read_flexport(ahd, FLXADDR_FLEXSTAT, &fstat);
if (error != 0) {
printf("%s: current sensing timeout 2\n",
ahd_name(ahd));
goto init_done;
}
}
if (i == 0) {
printf("%s: Timedout during current-sensing test\n",
ahd_name(ahd));
goto init_done;
}
/* Latch Current Sensing status. */
error = ahd_read_flexport(ahd, FLXADDR_CURRENT_STAT, &current_sensing);
if (error != 0) {
printf("%s: current sensing timeout 3\n", ahd_name(ahd));
goto init_done;
}
/* Diable current sensing. */
ahd_write_flexport(ahd, FLXADDR_ROMSTAT_CURSENSECTL, 0);
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_TERMCTL) != 0) {
printf("%s: current_sensing == 0x%x\n",
ahd_name(ahd), current_sensing);
}
#endif
warn_user = 0;
for (i = 0; i < 4; i++, current_sensing >>= FLX_CSTAT_SHIFT) {
u_int term_stat;
term_stat = (current_sensing & FLX_CSTAT_MASK);
switch (term_stat) {
case FLX_CSTAT_OVER:
case FLX_CSTAT_UNDER:
warn_user++;
case FLX_CSTAT_INVALID:
case FLX_CSTAT_OKAY:
if (warn_user == 0 && bootverbose == 0)
break;
printf("%s: %s Channel %s\n", ahd_name(ahd),
channel_strings[i], termstat_strings[term_stat]);
break;
}
}
if (warn_user) {
printf("%s: WARNING. Termination is not configured correctly.\n"
"%s: WARNING. SCSI bus operations may FAIL.\n",
ahd_name(ahd), ahd_name(ahd));
}
init_done:
ahd_restart(ahd);
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_timer_reset(&ahd->stat_timer, AHD_STAT_UPDATE_US,
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
ahd_stat_timer, ahd);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
return (0);
}
/*
* (Re)initialize chip state after a chip reset.
*/
static void
ahd_chip_init(struct ahd_softc *ahd)
{
uint32_t busaddr;
u_int sxfrctl1;
u_int scsiseq_template;
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
u_int wait;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
u_int i;
u_int target;
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
/*
* Take the LED out of diagnostic mode
*/
ahd_outb(ahd, SBLKCTL, ahd_inb(ahd, SBLKCTL) & ~(DIAGLEDEN|DIAGLEDON));
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
/*
* Return HS_MAILBOX to its default value.
*/
ahd->hs_mailbox = 0;
ahd_outb(ahd, HS_MAILBOX, 0);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/* Set the SCSI Id, SXFRCTL0, SXFRCTL1, and SIMODE1. */
ahd_outb(ahd, IOWNID, ahd->our_id);
ahd_outb(ahd, TOWNID, ahd->our_id);
sxfrctl1 = (ahd->flags & AHD_TERM_ENB_A) != 0 ? STPWEN : 0;
sxfrctl1 |= (ahd->flags & AHD_SPCHK_ENB_A) != 0 ? ENSPCHK : 0;
if ((ahd->bugs & AHD_LONG_SETIMO_BUG)
&& (ahd->seltime != STIMESEL_MIN)) {
/*
* The selection timer duration is twice as long
* as it should be. Halve it by adding "1" to
* the user specified setting.
*/
sxfrctl1 |= ahd->seltime + STIMESEL_BUG_ADJ;
} else {
sxfrctl1 |= ahd->seltime;
}
ahd_outb(ahd, SXFRCTL0, DFON);
ahd_outb(ahd, SXFRCTL1, sxfrctl1|ahd->seltime|ENSTIMER|ACTNEGEN);
ahd_outb(ahd, SIMODE1, ENSELTIMO|ENSCSIRST|ENSCSIPERR);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
/*
* Now that termination is set, wait for up
* to 500ms for our transceivers to settle. If
* the adapter does not have a cable attached,
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
* the transceivers may never settle, so don't
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
* complain if we fail here.
*/
for (wait = 10000;
(ahd_inb(ahd, SBLKCTL) & (ENAB40|ENAB20)) == 0 && wait;
wait--)
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_delay(100);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
/* Clear any false bus resets due to the transceivers settling */
ahd_outb(ahd, CLRSINT1, CLRSCSIRSTI);
ahd_outb(ahd, CLRINT, CLRSCSIINT);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/* Initialize mode specific S/G state. */
for (i = 0; i < 2; i++) {
ahd_set_modes(ahd, AHD_MODE_DFF0 + i, AHD_MODE_DFF0 + i);
ahd_outb(ahd, LONGJMP_ADDR + 1, INVALID_ADDR);
ahd_outb(ahd, SG_STATE, 0);
ahd_outb(ahd, CLRSEQINTSRC, 0xFF);
ahd_outb(ahd, SEQIMODE,
ENSAVEPTRS|ENCFG4DATA|ENCFG4ISTAT
|ENCFG4TSTAT|ENCFG4ICMD|ENCFG4TCMD);
}
ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG);
ahd_outb(ahd, DSCOMMAND0, ahd_inb(ahd, DSCOMMAND0)|MPARCKEN|CACHETHEN);
ahd_outb(ahd, DFF_THRSH, RD_DFTHRSH_75|WR_DFTHRSH_75);
ahd_outb(ahd, SIMODE0, ENIOERR|ENOVERRUN);
ahd_outb(ahd, SIMODE3, ENNTRAMPERR|ENOSRAMPERR);
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
if ((ahd->bugs & AHD_BUSFREEREV_BUG) != 0) {
ahd_outb(ahd, OPTIONMODE, AUTOACKEN|AUTO_MSGOUT_DE);
} else {
ahd_outb(ahd, OPTIONMODE, AUTOACKEN|BUSFREEREV|AUTO_MSGOUT_DE);
}
aic79xx.c: Clear the LQICRC_NLQ status should it pop up after we have already handled the SCSIPERR. During some streaming operations this status can be delayed until the stream ends. Without this change, the driver would complain about a "Missing case in ahd_handle_scsiint". In the LQOBUSFREE handler... Don't return the LQOMGR back to the idle state until after we have cleaned up ENSELO and any status related to this selection. The last thing we need is the LQO manager starting another select-out before we have updated the execution queue. It is not clear whether the LQOMGR would, or would not start a new selection early. Make sure ENSELO is off prior to clearing SELDO by flushing device writes. Move assignment of the next target SCB pointer inside of an if to make the code clearer. The effect is the same. Dump card state in both "Unexpected PKT busfree" paths. In ahd_reset(), set the chip to SCSI mode before reading SXFRCTL1. That register only exists in the SCSI mode. Also set the mode explicitly to the SCSI mode after chip reset due to paranoia. Re-arrange code so that SXFRCTL1 is restored as quickly after the chip reset as possible. S/G structurs must be 8byte aligned. Make this official by saying so in our DMA tag. Disable CIO bus stretch on MDFFSTAT if SHVALID is about to come true. This can cause a CIO bus lockup if a PCI or PCI-X error occurs while the stretch is occurring - the host cannot service the PCI-X error since the CIO bus is locked out and SHVALID will never resolve. The stretch was added in the Rev B to simplify the wait for SHVALID to resolve, but the code to do this in the open source sequencer is so simple it was never removed. Consistently use MAX_OFFSET for the user max syncrate set from non-volatile storage. This ensures that the offset does not conflict with AH?_OFFSET_UNKNOWN. Have ahd_pause_and_flushwork set the mode to ensure that it has access to the registers it checks. Also modify the checking of intstat so that the check against 0xFF can actually succeed if the INT_PEND mask is something other than 0xFF. Although there are no cardbus U320 controllers, this check may be needed to recover from a hot-plug PCI removal that occurs without informing the driver. Fix a typo. sg_prefetch_cnt -> sg_prefetch_align. This fixes an infinite loop at card initialization if the cacheline size is 0. aic79xx.h: Add AHD_EARLY_REQ_BUG bug flag. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. Change AH?_OFFSET_UNKNOWN to 0xFF. This is a value that the curr->offset can never be, unlike '0' which we previously used. This fixes code that only checks for a non-zero offset to determine if a sync negotiation is required since it will fire in the unknown case even if the goal is async. aic79xx.reg: Add comments for LQISTAT bits indicating their names in the 7902 data book. We use slightly different and more descriptive names in the firmware. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. aic79xx.seq: Update comments regarding rundown of the GSFIFO to reflect reality. Fix spelling errors. Since we use an 8byte address and 1 byte length, shorten the size of a block move for the legacy DMA'ed CDB case from 11 to 9 bytes. Remove code that, assuming the abort pending feature worked, would set MK_MESSAGE in the SCB's control byte on completion to catch invalid reselections. Since we don't see interrupts for completed selections, this status update could occur prior to us noticing the SELDO. The "select-out" queue logic will get confused by the MK_MESSAGE bit being set as this is used to catch packatized connections where we select-out with ATN. Since the abort pending feature doesn't work on any released controllers yet, this code was never executed. Add support for the AHD_EARLY_REQ_BUG. Don't ignore persistent REQ assertions just because they were asserted within the bus settle delay window. This allows us to tolerate devices like the GEM318 that violate the SCSI spec. Remove unintentional settnig of SG_CACHE_AVAIL. Writing this bit should have no effect, but who knows... On the Rev A, we must wait for HDMAENACK before loading additional segments to avoid clobbering the address of the first segment in the S/G FIFO. This resolves data-corruption issues with certain IBM (now Hitachi) and Fujitsu U320 drives. Rearrange calc_residual to avoid an extra jmp instruction. On RevA Silicon, if the target returns us to data-out after we have already trained for data-out, it is possible for us to transition the free running clock to data-valid before the required 100ns P1 setup time (8 P1 assertions in fast-160 mode). This will only happen if this L-Q is a continuation of a data transfer for which we have already prefetched data into our FIFO (LQ/Data followed by LQ/Data for the same write transaction). This can cause some target implementations to miss the first few data transfers on the bus. We detect this situation by noticing that this is the first data transfer after an LQ (LQIWORKONLQ true), that the data transfer is a continuation of a transfer already setup in our FIFO (SAVEPTRS interrupt), and that the transaction is a write (DIRECTION set in DFCNTRL). The delay is performed by disabling SCSIEN until we see the first REQ from the target. Only compile in snapshot savepointers handler for RevA silicon where it is enabled. Handle the cfg4icmd packetized interrupt. We just need to load the address and count, start the DMA, and CLRCHN once the transfer is complete. Fix an oversight in the overrun handler for packetized status operations. We need to wait for either CTXTDONE or an overrun when checking for an overrun. The previous code did not wait and thus could decide that no overrun had occurred even though an overrun will occur on the next data-valid req. Add some comment to this section for clarity. Use LAST_SEG_DONE instead of LASTSDONE for testing transfer completion in the packetized status case. LASTSDONE may come up more quickly since it only records completion on the SCSI side, but since LAST_SEG_DONE is used everywhere else (and needs to be), this is less confusing. Add a missing invalidation of the longjmp address in the non-pack handler. This code needs additional review. aic79xx_inline.h: Fix spelling error. aic79xx_osm.c: Set the cdb length for CDBs dma'ed from host memory. Add a comment indicating that, should CAM start supporting cdbs larger than 16bytes, the driver could store the CDB in the status buffer. aic79xx_pci.c: Add a table entry for the 39320A. Added a missing comma to an error string table. Fix spelling errors.
2003-02-27 23:23:16 +00:00
ahd_outb(ahd, SCSCHKN, CURRFIFODEF|WIDERESEN|SHVALIDSTDIS);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if ((ahd->chip & AHD_BUS_MASK) == AHD_PCIX)
/*
* Do not issue a target abort when a split completion
* error occurs. Let our PCIX interrupt handler deal
* with it instead. H2A4 Razor #625
*/
ahd_outb(ahd, PCIXCTL, ahd_inb(ahd, PCIXCTL) | SPLTSTADIS);
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
if ((ahd->bugs & AHD_LQOOVERRUN_BUG) != 0)
ahd_outb(ahd, LQOSCSCTL, LQONOCHKOVER);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*
* Tweak IOCELL settings.
*/
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
if ((ahd->flags & AHD_HP_BOARD) != 0) {
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
for (i = 0; i < NUMDSPS; i++) {
ahd_outb(ahd, DSPSELECT, i);
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
ahd_outb(ahd, WRTBIASCTL, WRTBIASCTL_HP_DEFAULT);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_MISC) != 0)
printf("%s: WRTBIASCTL now 0x%x\n", ahd_name(ahd),
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
WRTBIASCTL_HP_DEFAULT);
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
#endif
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
ahd_setup_iocell_workaround(ahd);
/*
* Enable LQI Manager interrupts.
*/
ahd_outb(ahd, LQIMODE1, ENLQIPHASE_LQ|ENLQIPHASE_NLQ|ENLIQABORT
| ENLQICRCI_LQ|ENLQICRCI_NLQ|ENLQIBADLQI
| ENLQIOVERI_LQ|ENLQIOVERI_NLQ);
ahd_outb(ahd, LQOMODE0, ENLQOATNLQ|ENLQOATNPKT|ENLQOTCRC);
/*
* An interrupt from LQOBUSFREE is made redundant by the
* BUSFREE interrupt. We choose to have the sequencer catch
* LQOPHCHGINPKT errors manually for the command phase at the
* start of a packetized selection case.
ahd_outb(ahd, LQOMODE1, ENLQOBUSFREE|ENLQOPHACHGINPKT);
*/
ahd_outb(ahd, LQOMODE1, 0);
/*
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
* Setup sequencer interrupt handlers.
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
*/
ahd_outw(ahd, INTVEC1_ADDR, ahd_resolve_seqaddr(ahd, LABEL_seq_isr));
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
ahd_outw(ahd, INTVEC2_ADDR, ahd_resolve_seqaddr(ahd, LABEL_timer_isr));
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*
* Setup SCB Offset registers.
*/
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
if ((ahd->bugs & AHD_PKT_LUN_BUG) != 0) {
ahd_outb(ahd, LUNPTR, offsetof(struct hardware_scb,
pkt_long_lun));
} else {
ahd_outb(ahd, LUNPTR, offsetof(struct hardware_scb, lun));
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_outb(ahd, CMDLENPTR, offsetof(struct hardware_scb, cdb_len));
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
ahd_outb(ahd, ATTRPTR, offsetof(struct hardware_scb, task_attribute));
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_outb(ahd, FLAGPTR, offsetof(struct hardware_scb, task_management));
ahd_outb(ahd, CMDPTR, offsetof(struct hardware_scb,
shared_data.idata.cdb));
ahd_outb(ahd, QNEXTPTR,
offsetof(struct hardware_scb, next_hscb_busaddr));
ahd_outb(ahd, ABRTBITPTR, MK_MESSAGE_BIT_OFFSET);
ahd_outb(ahd, ABRTBYTEPTR, offsetof(struct hardware_scb, control));
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
if ((ahd->bugs & AHD_PKT_LUN_BUG) != 0) {
ahd_outb(ahd, LUNLEN,
sizeof(ahd->next_queued_hscb->pkt_long_lun) - 1);
} else {
aic79xx.c: Use the special LUNLEN_SINGLE_LEVEL constant for post Rev A4 hardware for single byte luns. Without this change, Rev B hardware would place the single byte of lun data in byte 0 of the lun structure when it should be in byte 1. Since there are few if any devices on the market that support multiple luns in target mode, the corrupted lun field (which was only corrupted for non-zero luns) wasn't hurting us. Approved by: re (rwatson)
2003-05-30 02:15:15 +00:00
ahd_outb(ahd, LUNLEN, LUNLEN_SINGLE_LEVEL_LUN);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_outb(ahd, CDBLIMIT, SCB_CDB_LEN_PTR - 1);
ahd_outb(ahd, MAXCMD, 0xFF);
ahd_outb(ahd, SCBAUTOPTR,
AUSCBPTR_EN | offsetof(struct hardware_scb, tag));
/* We haven't been enabled for target mode yet. */
ahd_outb(ahd, MULTARGID, 0);
ahd_outb(ahd, MULTARGID + 1, 0);
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
/* Initialize the negotiation table. */
if ((ahd->features & AHD_NEW_IOCELL_OPTS) == 0) {
/*
* Clear the spare bytes in the neg table to avoid
* spurious parity errors.
*/
for (target = 0; target < AHD_NUM_TARGETS; target++) {
ahd_outb(ahd, NEGOADDR, target);
ahd_outb(ahd, ANNEXCOL, AHD_ANNEXCOL_PER_DEV0);
for (i = 0; i < AHD_NUM_PER_DEV_ANNEXCOLS; i++)
ahd_outb(ahd, ANNEXDAT, 0);
}
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
for (target = 0; target < AHD_NUM_TARGETS; target++) {
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
struct ahd_devinfo devinfo;
struct ahd_initiator_tinfo *tinfo;
struct ahd_tmode_tstate *tstate;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
tinfo = ahd_fetch_transinfo(ahd, 'A', ahd->our_id,
target, &tstate);
ahd_compile_devinfo(&devinfo, ahd->our_id,
target, CAM_LUN_WILDCARD,
'A', ROLE_INITIATOR);
ahd_update_neg_table(ahd, &devinfo, &tinfo->curr);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_outb(ahd, CLRSINT3, NTRAMPERR|OSRAMPERR);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
ahd_outb(ahd, CLRINT, CLRSCSIINT);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
Correct a typo in a comment. Add a comment in ahd_clear_critical_sections() about our need to leave ENBUSFREE set in SIMODE1 while single stepping. Re-arrange some delay loops so that we always perform a read after any register write and before the delay. This should make the delay loop more accurate. When completing message processing for a packetized commention, return the controller to a state where invalid non-packetized phases will still cause protocol violations. These are the same operations as those performed in the clear_target_state routine in the firmware. Now that we have a chip with working ABORTPENDING support (the 7901B), comment out the automatic use of this feature until we can adequately test it. The previous checkin updated the bug mask for the 7901B so this code was exercised. When resetting the bus, perform an ahd_flush_device_writes() call so that our reset assertion delay is acurately timed from when the reset bit is written to the controller.
2003-06-28 04:42:11 +00:00
#if NEEDS_MORE_TESTING
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*
* Always enable abort on incoming L_Qs if this feature is
* supported. We use this to catch invalid SCB references.
*/
if ((ahd->bugs & AHD_ABORT_LQI_BUG) == 0)
ahd_outb(ahd, LQCTL1, ABORTPENDING);
else
Correct a typo in a comment. Add a comment in ahd_clear_critical_sections() about our need to leave ENBUSFREE set in SIMODE1 while single stepping. Re-arrange some delay loops so that we always perform a read after any register write and before the delay. This should make the delay loop more accurate. When completing message processing for a packetized commention, return the controller to a state where invalid non-packetized phases will still cause protocol violations. These are the same operations as those performed in the clear_target_state routine in the firmware. Now that we have a chip with working ABORTPENDING support (the 7901B), comment out the automatic use of this feature until we can adequately test it. The previous checkin updated the bug mask for the 7901B so this code was exercised. When resetting the bus, perform an ahd_flush_device_writes() call so that our reset assertion delay is acurately timed from when the reset bit is written to the controller.
2003-06-28 04:42:11 +00:00
#endif
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_outb(ahd, LQCTL1, 0);
/* All of our queues are empty */
ahd->qoutfifonext = 0;
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
ahd->qoutfifonext_valid_tag = QOUTFIFO_ENTRY_VALID_LE;
ahd_outb(ahd, QOUTFIFO_ENTRY_VALID_TAG, QOUTFIFO_ENTRY_VALID >> 8);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
for (i = 0; i < AHD_QOUT_SIZE; i++)
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
ahd->qoutfifo[i] = 0;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_sync_qoutfifo(ahd, BUS_DMASYNC_PREREAD);
ahd->qinfifonext = 0;
for (i = 0; i < AHD_QIN_SIZE; i++)
ahd->qinfifo[i] = SCB_LIST_NULL;
if ((ahd->features & AHD_TARGETMODE) != 0) {
/* All target command blocks start out invalid. */
for (i = 0; i < AHD_TMODE_CMDS; i++)
ahd->targetcmds[i].cmd_valid = 0;
ahd_sync_tqinfifo(ahd, BUS_DMASYNC_PREREAD);
ahd->tqinfifonext = 1;
ahd_outb(ahd, KERNEL_TQINPOS, ahd->tqinfifonext - 1);
ahd_outb(ahd, TQINPOS, ahd->tqinfifonext);
}
/* Initialize Scratch Ram. */
ahd_outb(ahd, SEQ_FLAGS, 0);
ahd_outb(ahd, SEQ_FLAGS2, 0);
/* We don't have any waiting selections */
ahd_outw(ahd, WAITING_TID_HEAD, SCB_LIST_NULL);
ahd_outw(ahd, WAITING_TID_TAIL, SCB_LIST_NULL);
for (i = 0; i < AHD_NUM_TARGETS; i++)
ahd_outw(ahd, WAITING_SCB_TAILS + (2 * i), SCB_LIST_NULL);
/*
* Nobody is waiting to be DMAed into the QOUTFIFO.
*/
ahd_outw(ahd, COMPLETE_SCB_HEAD, SCB_LIST_NULL);
ahd_outw(ahd, COMPLETE_SCB_DMAINPROG_HEAD, SCB_LIST_NULL);
ahd_outw(ahd, COMPLETE_DMA_SCB_HEAD, SCB_LIST_NULL);
/*
* The Freeze Count is 0.
*/
ahd_outw(ahd, QFREEZE_COUNT, 0);
/*
* Tell the sequencer where it can find our arrays in memory.
*/
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
busaddr = ahd->shared_data_map.busaddr;
ahd_outl(ahd, SHARED_DATA_ADDR, busaddr);
ahd_outl(ahd, QOUTFIFO_NEXT_ADDR, busaddr);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*
* Setup the allowed SCSI Sequences based on operational mode.
* If we are a target, we'll enable select in operations once
* we've had a lun enabled.
*/
scsiseq_template = ENAUTOATNP;
if ((ahd->flags & AHD_INITIATORROLE) != 0)
scsiseq_template |= ENRSELI;
ahd_outb(ahd, SCSISEQ_TEMPLATE, scsiseq_template);
/* There are no busy SCBs yet. */
for (target = 0; target < AHD_NUM_TARGETS; target++) {
int lun;
for (lun = 0; lun < AHD_NUM_LUNS_NONPKT; lun++)
ahd_unbusy_tcl(ahd, BUILD_TCL_RAW(target, 'A', lun));
}
/*
* Initialize the group code to command length table.
* Vendor Unique codes are set to 0 so we only capture
* the first byte of the cdb. These can be overridden
* when target mode is enabled.
*/
ahd_outb(ahd, CMDSIZE_TABLE, 5);
ahd_outb(ahd, CMDSIZE_TABLE + 1, 9);
ahd_outb(ahd, CMDSIZE_TABLE + 2, 9);
ahd_outb(ahd, CMDSIZE_TABLE + 3, 0);
ahd_outb(ahd, CMDSIZE_TABLE + 4, 15);
ahd_outb(ahd, CMDSIZE_TABLE + 5, 11);
ahd_outb(ahd, CMDSIZE_TABLE + 6, 0);
ahd_outb(ahd, CMDSIZE_TABLE + 7, 0);
/* Tell the sequencer of our initial queue positions */
ahd_set_modes(ahd, AHD_MODE_CCHAN, AHD_MODE_CCHAN);
ahd_outb(ahd, QOFF_CTLSTA, SCB_QSIZE_512);
ahd->qinfifonext = 0;
ahd_set_hnscb_qoff(ahd, ahd->qinfifonext);
ahd_set_hescb_qoff(ahd, 0);
ahd_set_snscb_qoff(ahd, 0);
ahd_set_sescb_qoff(ahd, 0);
ahd_set_sdscb_qoff(ahd, 0);
/*
* Tell the sequencer which SCB will be the next one it receives.
*/
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
busaddr = aic_le32toh(ahd->next_queued_hscb->hscb_busaddr);
ahd_outl(ahd, NEXT_QUEUED_SCB_ADDR, busaddr);
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
/*
Fixup spelling of "coalesce" and derivatives. Approved by: RE
2003-05-26 21:10:58 +00:00
* Default to coalescing disabled.
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
*/
Fixup spelling of "coalesce" and derivatives. Approved by: RE
2003-05-26 21:10:58 +00:00
ahd_outw(ahd, INT_COALESCING_CMDCOUNT, 0);
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
ahd_outw(ahd, CMDS_PENDING, 0);
Fixup spelling of "coalesce" and derivatives. Approved by: RE
2003-05-26 21:10:58 +00:00
ahd_update_coalescing_values(ahd, ahd->int_coalescing_timer,
ahd->int_coalescing_maxcmds,
ahd->int_coalescing_mincmds);
ahd_enable_coalescing(ahd, FALSE);
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_loadseq(ahd);
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
}
/*
* Setup default device and controller settings.
* This should only be called if our probe has
* determined that no configuration data is available.
*/
int
ahd_default_config(struct ahd_softc *ahd)
{
int targ;
ahd->our_id = 7;
/*
* Allocate a tstate to house information for our
* initiator presence on the bus as well as the user
* data for any target mode initiator.
*/
if (ahd_alloc_tstate(ahd, ahd->our_id, 'A') == NULL) {
printf("%s: unable to allocate ahd_tmode_tstate. "
"Failing attach\n", ahd_name(ahd));
return (ENOMEM);
}
for (targ = 0; targ < AHD_NUM_TARGETS; targ++) {
struct ahd_devinfo devinfo;
struct ahd_initiator_tinfo *tinfo;
struct ahd_tmode_tstate *tstate;
uint16_t target_mask;
tinfo = ahd_fetch_transinfo(ahd, 'A', ahd->our_id,
targ, &tstate);
/*
* We support SPC2 and SPI4.
*/
tinfo->user.protocol_version = 4;
tinfo->user.transport_version = 4;
target_mask = 0x01 << targ;
ahd->user_discenable |= target_mask;
tstate->discenable |= target_mask;
ahd->user_tagenable |= target_mask;
#ifdef AHD_FORCE_160
tinfo->user.period = AHD_SYNCRATE_DT;
#else
tinfo->user.period = AHD_SYNCRATE_160;
#endif
aic79xx.c: Clear the LQICRC_NLQ status should it pop up after we have already handled the SCSIPERR. During some streaming operations this status can be delayed until the stream ends. Without this change, the driver would complain about a "Missing case in ahd_handle_scsiint". In the LQOBUSFREE handler... Don't return the LQOMGR back to the idle state until after we have cleaned up ENSELO and any status related to this selection. The last thing we need is the LQO manager starting another select-out before we have updated the execution queue. It is not clear whether the LQOMGR would, or would not start a new selection early. Make sure ENSELO is off prior to clearing SELDO by flushing device writes. Move assignment of the next target SCB pointer inside of an if to make the code clearer. The effect is the same. Dump card state in both "Unexpected PKT busfree" paths. In ahd_reset(), set the chip to SCSI mode before reading SXFRCTL1. That register only exists in the SCSI mode. Also set the mode explicitly to the SCSI mode after chip reset due to paranoia. Re-arrange code so that SXFRCTL1 is restored as quickly after the chip reset as possible. S/G structurs must be 8byte aligned. Make this official by saying so in our DMA tag. Disable CIO bus stretch on MDFFSTAT if SHVALID is about to come true. This can cause a CIO bus lockup if a PCI or PCI-X error occurs while the stretch is occurring - the host cannot service the PCI-X error since the CIO bus is locked out and SHVALID will never resolve. The stretch was added in the Rev B to simplify the wait for SHVALID to resolve, but the code to do this in the open source sequencer is so simple it was never removed. Consistently use MAX_OFFSET for the user max syncrate set from non-volatile storage. This ensures that the offset does not conflict with AH?_OFFSET_UNKNOWN. Have ahd_pause_and_flushwork set the mode to ensure that it has access to the registers it checks. Also modify the checking of intstat so that the check against 0xFF can actually succeed if the INT_PEND mask is something other than 0xFF. Although there are no cardbus U320 controllers, this check may be needed to recover from a hot-plug PCI removal that occurs without informing the driver. Fix a typo. sg_prefetch_cnt -> sg_prefetch_align. This fixes an infinite loop at card initialization if the cacheline size is 0. aic79xx.h: Add AHD_EARLY_REQ_BUG bug flag. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. Change AH?_OFFSET_UNKNOWN to 0xFF. This is a value that the curr->offset can never be, unlike '0' which we previously used. This fixes code that only checks for a non-zero offset to determine if a sync negotiation is required since it will fire in the unknown case even if the goal is async. aic79xx.reg: Add comments for LQISTAT bits indicating their names in the 7902 data book. We use slightly different and more descriptive names in the firmware. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. aic79xx.seq: Update comments regarding rundown of the GSFIFO to reflect reality. Fix spelling errors. Since we use an 8byte address and 1 byte length, shorten the size of a block move for the legacy DMA'ed CDB case from 11 to 9 bytes. Remove code that, assuming the abort pending feature worked, would set MK_MESSAGE in the SCB's control byte on completion to catch invalid reselections. Since we don't see interrupts for completed selections, this status update could occur prior to us noticing the SELDO. The "select-out" queue logic will get confused by the MK_MESSAGE bit being set as this is used to catch packatized connections where we select-out with ATN. Since the abort pending feature doesn't work on any released controllers yet, this code was never executed. Add support for the AHD_EARLY_REQ_BUG. Don't ignore persistent REQ assertions just because they were asserted within the bus settle delay window. This allows us to tolerate devices like the GEM318 that violate the SCSI spec. Remove unintentional settnig of SG_CACHE_AVAIL. Writing this bit should have no effect, but who knows... On the Rev A, we must wait for HDMAENACK before loading additional segments to avoid clobbering the address of the first segment in the S/G FIFO. This resolves data-corruption issues with certain IBM (now Hitachi) and Fujitsu U320 drives. Rearrange calc_residual to avoid an extra jmp instruction. On RevA Silicon, if the target returns us to data-out after we have already trained for data-out, it is possible for us to transition the free running clock to data-valid before the required 100ns P1 setup time (8 P1 assertions in fast-160 mode). This will only happen if this L-Q is a continuation of a data transfer for which we have already prefetched data into our FIFO (LQ/Data followed by LQ/Data for the same write transaction). This can cause some target implementations to miss the first few data transfers on the bus. We detect this situation by noticing that this is the first data transfer after an LQ (LQIWORKONLQ true), that the data transfer is a continuation of a transfer already setup in our FIFO (SAVEPTRS interrupt), and that the transaction is a write (DIRECTION set in DFCNTRL). The delay is performed by disabling SCSIEN until we see the first REQ from the target. Only compile in snapshot savepointers handler for RevA silicon where it is enabled. Handle the cfg4icmd packetized interrupt. We just need to load the address and count, start the DMA, and CLRCHN once the transfer is complete. Fix an oversight in the overrun handler for packetized status operations. We need to wait for either CTXTDONE or an overrun when checking for an overrun. The previous code did not wait and thus could decide that no overrun had occurred even though an overrun will occur on the next data-valid req. Add some comment to this section for clarity. Use LAST_SEG_DONE instead of LASTSDONE for testing transfer completion in the packetized status case. LASTSDONE may come up more quickly since it only records completion on the SCSI side, but since LAST_SEG_DONE is used everywhere else (and needs to be), this is less confusing. Add a missing invalidation of the longjmp address in the non-pack handler. This code needs additional review. aic79xx_inline.h: Fix spelling error. aic79xx_osm.c: Set the cdb length for CDBs dma'ed from host memory. Add a comment indicating that, should CAM start supporting cdbs larger than 16bytes, the driver could store the CDB in the status buffer. aic79xx_pci.c: Add a table entry for the 39320A. Added a missing comma to an error string table. Fix spelling errors.
2003-02-27 23:23:16 +00:00
tinfo->user.offset = MAX_OFFSET;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
tinfo->user.ppr_options = MSG_EXT_PPR_RD_STRM
| MSG_EXT_PPR_WR_FLOW
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
| MSG_EXT_PPR_HOLD_MCS
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
| MSG_EXT_PPR_IU_REQ
| MSG_EXT_PPR_QAS_REQ
| MSG_EXT_PPR_DT_REQ;
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
if ((ahd->features & AHD_RTI) != 0)
tinfo->user.ppr_options |= MSG_EXT_PPR_RTI;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
tinfo->user.width = MSG_EXT_WDTR_BUS_16_BIT;
/*
* Start out Async/Narrow/Untagged and with
* conservative protocol support.
*/
tinfo->goal.protocol_version = 2;
tinfo->goal.transport_version = 2;
tinfo->curr.protocol_version = 2;
tinfo->curr.transport_version = 2;
ahd_compile_devinfo(&devinfo, ahd->our_id,
targ, CAM_LUN_WILDCARD,
'A', ROLE_INITIATOR);
tstate->tagenable &= ~target_mask;
ahd_set_width(ahd, &devinfo, MSG_EXT_WDTR_BUS_8_BIT,
AHD_TRANS_CUR|AHD_TRANS_GOAL, /*paused*/TRUE);
ahd_set_syncrate(ahd, &devinfo, /*period*/0, /*offset*/0,
/*ppr_options*/0, AHD_TRANS_CUR|AHD_TRANS_GOAL,
/*paused*/TRUE);
}
return (0);
}
/*
* Parse device configuration information.
*/
int
ahd_parse_cfgdata(struct ahd_softc *ahd, struct seeprom_config *sc)
{
int targ;
int max_targ;
max_targ = sc->max_targets & CFMAXTARG;
ahd->our_id = sc->brtime_id & CFSCSIID;
/*
* Allocate a tstate to house information for our
* initiator presence on the bus as well as the user
* data for any target mode initiator.
*/
if (ahd_alloc_tstate(ahd, ahd->our_id, 'A') == NULL) {
printf("%s: unable to allocate ahd_tmode_tstate. "
"Failing attach\n", ahd_name(ahd));
return (ENOMEM);
}
for (targ = 0; targ < max_targ; targ++) {
struct ahd_devinfo devinfo;
struct ahd_initiator_tinfo *tinfo;
struct ahd_transinfo *user_tinfo;
struct ahd_tmode_tstate *tstate;
uint16_t target_mask;
tinfo = ahd_fetch_transinfo(ahd, 'A', ahd->our_id,
targ, &tstate);
user_tinfo = &tinfo->user;
/*
* We support SPC2 and SPI4.
*/
tinfo->user.protocol_version = 4;
tinfo->user.transport_version = 4;
target_mask = 0x01 << targ;
ahd->user_discenable &= ~target_mask;
tstate->discenable &= ~target_mask;
ahd->user_tagenable &= ~target_mask;
if (sc->device_flags[targ] & CFDISC) {
tstate->discenable |= target_mask;
ahd->user_discenable |= target_mask;
ahd->user_tagenable |= target_mask;
} else {
/*
* Cannot be packetized without disconnection.
*/
sc->device_flags[targ] &= ~CFPACKETIZED;
}
user_tinfo->ppr_options = 0;
user_tinfo->period = (sc->device_flags[targ] & CFXFER);
if (user_tinfo->period < CFXFER_ASYNC) {
if (user_tinfo->period <= AHD_PERIOD_10MHz)
user_tinfo->ppr_options |= MSG_EXT_PPR_DT_REQ;
user_tinfo->offset = MAX_OFFSET;
} else {
user_tinfo->offset = 0;
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
user_tinfo->period = AHD_ASYNC_XFER_PERIOD;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
#ifdef AHD_FORCE_160
if (user_tinfo->period <= AHD_SYNCRATE_160)
user_tinfo->period = AHD_SYNCRATE_DT;
#endif
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
if ((sc->device_flags[targ] & CFPACKETIZED) != 0) {
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
user_tinfo->ppr_options |= MSG_EXT_PPR_RD_STRM
| MSG_EXT_PPR_WR_FLOW
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
| MSG_EXT_PPR_HOLD_MCS
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
| MSG_EXT_PPR_IU_REQ;
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
if ((ahd->features & AHD_RTI) != 0)
user_tinfo->ppr_options |= MSG_EXT_PPR_RTI;
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if ((sc->device_flags[targ] & CFQAS) != 0)
user_tinfo->ppr_options |= MSG_EXT_PPR_QAS_REQ;
if ((sc->device_flags[targ] & CFWIDEB) != 0)
user_tinfo->width = MSG_EXT_WDTR_BUS_16_BIT;
else
user_tinfo->width = MSG_EXT_WDTR_BUS_8_BIT;
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_MISC) != 0)
printf("(%d): %x:%x:%x:%x\n", targ, user_tinfo->width,
user_tinfo->period, user_tinfo->offset,
user_tinfo->ppr_options);
#endif
/*
* Start out Async/Narrow/Untagged and with
* conservative protocol support.
*/
tstate->tagenable &= ~target_mask;
tinfo->goal.protocol_version = 2;
tinfo->goal.transport_version = 2;
tinfo->curr.protocol_version = 2;
tinfo->curr.transport_version = 2;
ahd_compile_devinfo(&devinfo, ahd->our_id,
targ, CAM_LUN_WILDCARD,
'A', ROLE_INITIATOR);
ahd_set_width(ahd, &devinfo, MSG_EXT_WDTR_BUS_8_BIT,
AHD_TRANS_CUR|AHD_TRANS_GOAL, /*paused*/TRUE);
ahd_set_syncrate(ahd, &devinfo, /*period*/0, /*offset*/0,
/*ppr_options*/0, AHD_TRANS_CUR|AHD_TRANS_GOAL,
/*paused*/TRUE);
}
ahd->flags &= ~AHD_SPCHK_ENB_A;
if (sc->bios_control & CFSPARITY)
ahd->flags |= AHD_SPCHK_ENB_A;
ahd->flags &= ~AHD_RESET_BUS_A;
if (sc->bios_control & CFRESETB)
ahd->flags |= AHD_RESET_BUS_A;
ahd->flags &= ~AHD_EXTENDED_TRANS_A;
if (sc->bios_control & CFEXTEND)
ahd->flags |= AHD_EXTENDED_TRANS_A;
ahd->flags &= ~AHD_BIOS_ENABLED;
if ((sc->bios_control & CFBIOSSTATE) == CFBS_ENABLED)
ahd->flags |= AHD_BIOS_ENABLED;
ahd->flags &= ~AHD_STPWLEVEL_A;
if ((sc->adapter_control & CFSTPWLEVEL) != 0)
ahd->flags |= AHD_STPWLEVEL_A;
return (0);
}
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
/*
* Parse device configuration information.
*/
int
ahd_parse_vpddata(struct ahd_softc *ahd, struct vpd_config *vpd)
{
int error;
error = ahd_verify_vpd_cksum(vpd);
if (error == 0)
return (EINVAL);
if ((vpd->bios_flags & VPDBOOTHOST) != 0)
ahd->flags |= AHD_BOOT_CHANNEL;
return (0);
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
void
ahd_intr_enable(struct ahd_softc *ahd, int enable)
{
u_int hcntrl;
hcntrl = ahd_inb(ahd, HCNTRL);
hcntrl &= ~INTEN;
ahd->pause &= ~INTEN;
ahd->unpause &= ~INTEN;
if (enable) {
hcntrl |= INTEN;
ahd->pause |= INTEN;
ahd->unpause |= INTEN;
}
ahd_outb(ahd, HCNTRL, hcntrl);
}
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
void
Fixup spelling of "coalesce" and derivatives. Approved by: RE
2003-05-26 21:10:58 +00:00
ahd_update_coalescing_values(struct ahd_softc *ahd, u_int timer, u_int maxcmds,
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
u_int mincmds)
{
if (timer > AHD_TIMER_MAX_US)
timer = AHD_TIMER_MAX_US;
Fixup spelling of "coalesce" and derivatives. Approved by: RE
2003-05-26 21:10:58 +00:00
ahd->int_coalescing_timer = timer;
if (maxcmds > AHD_INT_COALESCING_MAXCMDS_MAX)
maxcmds = AHD_INT_COALESCING_MAXCMDS_MAX;
if (mincmds > AHD_INT_COALESCING_MINCMDS_MAX)
mincmds = AHD_INT_COALESCING_MINCMDS_MAX;
ahd->int_coalescing_maxcmds = maxcmds;
ahd_outw(ahd, INT_COALESCING_TIMER, timer / AHD_TIMER_US_PER_TICK);
ahd_outb(ahd, INT_COALESCING_MAXCMDS, -maxcmds);
ahd_outb(ahd, INT_COALESCING_MINCMDS, -mincmds);
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
}
void
Fixup spelling of "coalesce" and derivatives. Approved by: RE
2003-05-26 21:10:58 +00:00
ahd_enable_coalescing(struct ahd_softc *ahd, int enable)
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
{
Fixup spelling of "coalesce" and derivatives. Approved by: RE
2003-05-26 21:10:58 +00:00
ahd->hs_mailbox &= ~ENINT_COALESCE;
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
if (enable)
Fixup spelling of "coalesce" and derivatives. Approved by: RE
2003-05-26 21:10:58 +00:00
ahd->hs_mailbox |= ENINT_COALESCE;
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
ahd_outb(ahd, HS_MAILBOX, ahd->hs_mailbox);
ahd_flush_device_writes(ahd);
ahd_run_qoutfifo(ahd);
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*
* Ensure that the card is paused in a location
* outside of all critical sections and that all
* pending work is completed prior to returning.
* This routine should only be called from outside
* an interrupt context.
*/
void
ahd_pause_and_flushwork(struct ahd_softc *ahd)
{
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
u_int intstat;
u_int maxloops;
u_int qfreeze_cnt;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
maxloops = 1000;
ahd->flags |= AHD_ALL_INTERRUPTS;
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
ahd_pause(ahd);
/*
* Increment the QFreeze Count so that the sequencer
* will not start new selections. We do this only
* until we are safely paused without further selections
* pending.
*/
ahd_outw(ahd, QFREEZE_COUNT, ahd_inw(ahd, QFREEZE_COUNT) + 1);
ahd_outb(ahd, SEQ_FLAGS2, ahd_inb(ahd, SEQ_FLAGS2) | SELECTOUT_QFROZEN);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
do {
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
struct scb *waiting_scb;
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
ahd_unpause(ahd);
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
/*
* Give the sequencer some time to service
* any active selections.
*/
aic_delay(200);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_intr(ahd);
ahd_pause(ahd);
ahd_clear_critical_section(ahd);
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
intstat = ahd_inb(ahd, INTSTAT);
aic79xx.c: Clear the LQICRC_NLQ status should it pop up after we have already handled the SCSIPERR. During some streaming operations this status can be delayed until the stream ends. Without this change, the driver would complain about a "Missing case in ahd_handle_scsiint". In the LQOBUSFREE handler... Don't return the LQOMGR back to the idle state until after we have cleaned up ENSELO and any status related to this selection. The last thing we need is the LQO manager starting another select-out before we have updated the execution queue. It is not clear whether the LQOMGR would, or would not start a new selection early. Make sure ENSELO is off prior to clearing SELDO by flushing device writes. Move assignment of the next target SCB pointer inside of an if to make the code clearer. The effect is the same. Dump card state in both "Unexpected PKT busfree" paths. In ahd_reset(), set the chip to SCSI mode before reading SXFRCTL1. That register only exists in the SCSI mode. Also set the mode explicitly to the SCSI mode after chip reset due to paranoia. Re-arrange code so that SXFRCTL1 is restored as quickly after the chip reset as possible. S/G structurs must be 8byte aligned. Make this official by saying so in our DMA tag. Disable CIO bus stretch on MDFFSTAT if SHVALID is about to come true. This can cause a CIO bus lockup if a PCI or PCI-X error occurs while the stretch is occurring - the host cannot service the PCI-X error since the CIO bus is locked out and SHVALID will never resolve. The stretch was added in the Rev B to simplify the wait for SHVALID to resolve, but the code to do this in the open source sequencer is so simple it was never removed. Consistently use MAX_OFFSET for the user max syncrate set from non-volatile storage. This ensures that the offset does not conflict with AH?_OFFSET_UNKNOWN. Have ahd_pause_and_flushwork set the mode to ensure that it has access to the registers it checks. Also modify the checking of intstat so that the check against 0xFF can actually succeed if the INT_PEND mask is something other than 0xFF. Although there are no cardbus U320 controllers, this check may be needed to recover from a hot-plug PCI removal that occurs without informing the driver. Fix a typo. sg_prefetch_cnt -> sg_prefetch_align. This fixes an infinite loop at card initialization if the cacheline size is 0. aic79xx.h: Add AHD_EARLY_REQ_BUG bug flag. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. Change AH?_OFFSET_UNKNOWN to 0xFF. This is a value that the curr->offset can never be, unlike '0' which we previously used. This fixes code that only checks for a non-zero offset to determine if a sync negotiation is required since it will fire in the unknown case even if the goal is async. aic79xx.reg: Add comments for LQISTAT bits indicating their names in the 7902 data book. We use slightly different and more descriptive names in the firmware. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. aic79xx.seq: Update comments regarding rundown of the GSFIFO to reflect reality. Fix spelling errors. Since we use an 8byte address and 1 byte length, shorten the size of a block move for the legacy DMA'ed CDB case from 11 to 9 bytes. Remove code that, assuming the abort pending feature worked, would set MK_MESSAGE in the SCB's control byte on completion to catch invalid reselections. Since we don't see interrupts for completed selections, this status update could occur prior to us noticing the SELDO. The "select-out" queue logic will get confused by the MK_MESSAGE bit being set as this is used to catch packatized connections where we select-out with ATN. Since the abort pending feature doesn't work on any released controllers yet, this code was never executed. Add support for the AHD_EARLY_REQ_BUG. Don't ignore persistent REQ assertions just because they were asserted within the bus settle delay window. This allows us to tolerate devices like the GEM318 that violate the SCSI spec. Remove unintentional settnig of SG_CACHE_AVAIL. Writing this bit should have no effect, but who knows... On the Rev A, we must wait for HDMAENACK before loading additional segments to avoid clobbering the address of the first segment in the S/G FIFO. This resolves data-corruption issues with certain IBM (now Hitachi) and Fujitsu U320 drives. Rearrange calc_residual to avoid an extra jmp instruction. On RevA Silicon, if the target returns us to data-out after we have already trained for data-out, it is possible for us to transition the free running clock to data-valid before the required 100ns P1 setup time (8 P1 assertions in fast-160 mode). This will only happen if this L-Q is a continuation of a data transfer for which we have already prefetched data into our FIFO (LQ/Data followed by LQ/Data for the same write transaction). This can cause some target implementations to miss the first few data transfers on the bus. We detect this situation by noticing that this is the first data transfer after an LQ (LQIWORKONLQ true), that the data transfer is a continuation of a transfer already setup in our FIFO (SAVEPTRS interrupt), and that the transaction is a write (DIRECTION set in DFCNTRL). The delay is performed by disabling SCSIEN until we see the first REQ from the target. Only compile in snapshot savepointers handler for RevA silicon where it is enabled. Handle the cfg4icmd packetized interrupt. We just need to load the address and count, start the DMA, and CLRCHN once the transfer is complete. Fix an oversight in the overrun handler for packetized status operations. We need to wait for either CTXTDONE or an overrun when checking for an overrun. The previous code did not wait and thus could decide that no overrun had occurred even though an overrun will occur on the next data-valid req. Add some comment to this section for clarity. Use LAST_SEG_DONE instead of LASTSDONE for testing transfer completion in the packetized status case. LASTSDONE may come up more quickly since it only records completion on the SCSI side, but since LAST_SEG_DONE is used everywhere else (and needs to be), this is less confusing. Add a missing invalidation of the longjmp address in the non-pack handler. This code needs additional review. aic79xx_inline.h: Fix spelling error. aic79xx_osm.c: Set the cdb length for CDBs dma'ed from host memory. Add a comment indicating that, should CAM start supporting cdbs larger than 16bytes, the driver could store the CDB in the status buffer. aic79xx_pci.c: Add a table entry for the 39320A. Added a missing comma to an error string table. Fix spelling errors.
2003-02-27 23:23:16 +00:00
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
if ((ahd_inb(ahd, SSTAT0) & (SELDO|SELINGO)) == 0)
ahd_outb(ahd, SCSISEQ0,
ahd_inb(ahd, SCSISEQ0) & ~ENSELO);
/*
* In the non-packetized case, the sequencer (for Rev A),
* relies on ENSELO remaining set after SELDO. The hardware
* auto-clears ENSELO in the packetized case.
*/
waiting_scb = ahd_lookup_scb(ahd,
ahd_inw(ahd, WAITING_TID_HEAD));
if (waiting_scb != NULL
&& (waiting_scb->flags & SCB_PACKETIZED) == 0
&& (ahd_inb(ahd, SSTAT0) & (SELDO|SELINGO)) != 0)
ahd_outb(ahd, SCSISEQ0,
ahd_inb(ahd, SCSISEQ0) | ENSELO);
} while (--maxloops
aic79xx.c: Clear the LQICRC_NLQ status should it pop up after we have already handled the SCSIPERR. During some streaming operations this status can be delayed until the stream ends. Without this change, the driver would complain about a "Missing case in ahd_handle_scsiint". In the LQOBUSFREE handler... Don't return the LQOMGR back to the idle state until after we have cleaned up ENSELO and any status related to this selection. The last thing we need is the LQO manager starting another select-out before we have updated the execution queue. It is not clear whether the LQOMGR would, or would not start a new selection early. Make sure ENSELO is off prior to clearing SELDO by flushing device writes. Move assignment of the next target SCB pointer inside of an if to make the code clearer. The effect is the same. Dump card state in both "Unexpected PKT busfree" paths. In ahd_reset(), set the chip to SCSI mode before reading SXFRCTL1. That register only exists in the SCSI mode. Also set the mode explicitly to the SCSI mode after chip reset due to paranoia. Re-arrange code so that SXFRCTL1 is restored as quickly after the chip reset as possible. S/G structurs must be 8byte aligned. Make this official by saying so in our DMA tag. Disable CIO bus stretch on MDFFSTAT if SHVALID is about to come true. This can cause a CIO bus lockup if a PCI or PCI-X error occurs while the stretch is occurring - the host cannot service the PCI-X error since the CIO bus is locked out and SHVALID will never resolve. The stretch was added in the Rev B to simplify the wait for SHVALID to resolve, but the code to do this in the open source sequencer is so simple it was never removed. Consistently use MAX_OFFSET for the user max syncrate set from non-volatile storage. This ensures that the offset does not conflict with AH?_OFFSET_UNKNOWN. Have ahd_pause_and_flushwork set the mode to ensure that it has access to the registers it checks. Also modify the checking of intstat so that the check against 0xFF can actually succeed if the INT_PEND mask is something other than 0xFF. Although there are no cardbus U320 controllers, this check may be needed to recover from a hot-plug PCI removal that occurs without informing the driver. Fix a typo. sg_prefetch_cnt -> sg_prefetch_align. This fixes an infinite loop at card initialization if the cacheline size is 0. aic79xx.h: Add AHD_EARLY_REQ_BUG bug flag. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. Change AH?_OFFSET_UNKNOWN to 0xFF. This is a value that the curr->offset can never be, unlike '0' which we previously used. This fixes code that only checks for a non-zero offset to determine if a sync negotiation is required since it will fire in the unknown case even if the goal is async. aic79xx.reg: Add comments for LQISTAT bits indicating their names in the 7902 data book. We use slightly different and more descriptive names in the firmware. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. aic79xx.seq: Update comments regarding rundown of the GSFIFO to reflect reality. Fix spelling errors. Since we use an 8byte address and 1 byte length, shorten the size of a block move for the legacy DMA'ed CDB case from 11 to 9 bytes. Remove code that, assuming the abort pending feature worked, would set MK_MESSAGE in the SCB's control byte on completion to catch invalid reselections. Since we don't see interrupts for completed selections, this status update could occur prior to us noticing the SELDO. The "select-out" queue logic will get confused by the MK_MESSAGE bit being set as this is used to catch packatized connections where we select-out with ATN. Since the abort pending feature doesn't work on any released controllers yet, this code was never executed. Add support for the AHD_EARLY_REQ_BUG. Don't ignore persistent REQ assertions just because they were asserted within the bus settle delay window. This allows us to tolerate devices like the GEM318 that violate the SCSI spec. Remove unintentional settnig of SG_CACHE_AVAIL. Writing this bit should have no effect, but who knows... On the Rev A, we must wait for HDMAENACK before loading additional segments to avoid clobbering the address of the first segment in the S/G FIFO. This resolves data-corruption issues with certain IBM (now Hitachi) and Fujitsu U320 drives. Rearrange calc_residual to avoid an extra jmp instruction. On RevA Silicon, if the target returns us to data-out after we have already trained for data-out, it is possible for us to transition the free running clock to data-valid before the required 100ns P1 setup time (8 P1 assertions in fast-160 mode). This will only happen if this L-Q is a continuation of a data transfer for which we have already prefetched data into our FIFO (LQ/Data followed by LQ/Data for the same write transaction). This can cause some target implementations to miss the first few data transfers on the bus. We detect this situation by noticing that this is the first data transfer after an LQ (LQIWORKONLQ true), that the data transfer is a continuation of a transfer already setup in our FIFO (SAVEPTRS interrupt), and that the transaction is a write (DIRECTION set in DFCNTRL). The delay is performed by disabling SCSIEN until we see the first REQ from the target. Only compile in snapshot savepointers handler for RevA silicon where it is enabled. Handle the cfg4icmd packetized interrupt. We just need to load the address and count, start the DMA, and CLRCHN once the transfer is complete. Fix an oversight in the overrun handler for packetized status operations. We need to wait for either CTXTDONE or an overrun when checking for an overrun. The previous code did not wait and thus could decide that no overrun had occurred even though an overrun will occur on the next data-valid req. Add some comment to this section for clarity. Use LAST_SEG_DONE instead of LASTSDONE for testing transfer completion in the packetized status case. LASTSDONE may come up more quickly since it only records completion on the SCSI side, but since LAST_SEG_DONE is used everywhere else (and needs to be), this is less confusing. Add a missing invalidation of the longjmp address in the non-pack handler. This code needs additional review. aic79xx_inline.h: Fix spelling error. aic79xx_osm.c: Set the cdb length for CDBs dma'ed from host memory. Add a comment indicating that, should CAM start supporting cdbs larger than 16bytes, the driver could store the CDB in the status buffer. aic79xx_pci.c: Add a table entry for the 39320A. Added a missing comma to an error string table. Fix spelling errors.
2003-02-27 23:23:16 +00:00
&& (intstat != 0xFF || (ahd->features & AHD_REMOVABLE) == 0)
&& ((intstat & INT_PEND) != 0
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
|| (ahd_inb(ahd, SCSISEQ0) & ENSELO) != 0
|| (ahd_inb(ahd, SSTAT0) & (SELDO|SELINGO)) != 0));
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if (maxloops == 0) {
printf("Infinite interrupt loop, INTSTAT = %x",
ahd_inb(ahd, INTSTAT));
}
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
qfreeze_cnt = ahd_inw(ahd, QFREEZE_COUNT);
if (qfreeze_cnt == 0) {
printf("%s: ahd_pause_and_flushwork with 0 qfreeze count!\n",
ahd_name(ahd));
} else {
qfreeze_cnt--;
}
ahd_outw(ahd, QFREEZE_COUNT, qfreeze_cnt);
if (qfreeze_cnt == 0)
ahd_outb(ahd, SEQ_FLAGS2,
ahd_inb(ahd, SEQ_FLAGS2) & ~SELECTOUT_QFROZEN);
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
ahd_flush_qoutfifo(ahd);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_platform_flushwork(ahd);
ahd->flags &= ~AHD_ALL_INTERRUPTS;
}
int
ahd_suspend(struct ahd_softc *ahd)
{
ahd_pause_and_flushwork(ahd);
aic7770.c: aic79xx.c: aic79xx.h: aic79xx_pci.c: aic7xxx.c: aic7xxx.h: aic7xxx_pci.c: Switch ah?_reset() to take an additional "reinit" argument. Use this instead of init_level to determin if the chip should be fully reinitialized after a chip reset. This is required so that ah?_shutdown() can reset the chip without side-effects. aic79xx.c: Implement ahd_suspend() and ahd_resume(). aic7xxx.c: Change ahc_loadseq() to *not* restart the sequencer. This brings the loadseq behavior in line with that of the 7902 driver and also simplifies the init routine. Correct the resume routine to enable interrupts and restart the sequencer.
2003-06-06 23:48:19 +00:00
if (LIST_FIRST(&ahd->pending_scbs) != NULL) {
ahd_unpause(ahd);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
return (EBUSY);
}
ahd_shutdown(ahd);
return (0);
}
int
ahd_resume(struct ahd_softc *ahd)
{
aic7770.c: aic79xx.c: aic79xx.h: aic79xx_pci.c: aic7xxx.c: aic7xxx.h: aic7xxx_pci.c: Switch ah?_reset() to take an additional "reinit" argument. Use this instead of init_level to determin if the chip should be fully reinitialized after a chip reset. This is required so that ah?_shutdown() can reset the chip without side-effects. aic79xx.c: Implement ahd_suspend() and ahd_resume(). aic7xxx.c: Change ahc_loadseq() to *not* restart the sequencer. This brings the loadseq behavior in line with that of the 7902 driver and also simplifies the init routine. Correct the resume routine to enable interrupts and restart the sequencer.
2003-06-06 23:48:19 +00:00
ahd_reset(ahd, /*reinit*/TRUE);
ahd_intr_enable(ahd, TRUE);
ahd_restart(ahd);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
return (0);
}
/************************** Busy Target Table *********************************/
/*
* Set SCBPTR to the SCB that contains the busy
* table entry for TCL. Return the offset into
* the SCB that contains the entry for TCL.
* saved_scbid is dereferenced and set to the
* scbid that should be restored once manipualtion
* of the TCL entry is complete.
*/
static __inline u_int
ahd_index_busy_tcl(struct ahd_softc *ahd, u_int *saved_scbid, u_int tcl)
{
/*
* Index to the SCB that contains the busy entry.
*/
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
AHD_ASSERT_MODES(ahd, AHD_MODE_SCSI_MSK, AHD_MODE_SCSI_MSK);
*saved_scbid = ahd_get_scbptr(ahd);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_set_scbptr(ahd, TCL_LUN(tcl)
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
| ((TCL_TARGET_OFFSET(tcl) & 0xC) << 4));
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*
* And now calculate the SCB offset to the entry.
* Each entry is 2 bytes wide, hence the
* multiplication by 2.
*/
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
return (((TCL_TARGET_OFFSET(tcl) & 0x3) << 1) + SCB_DISCONNECTED_LISTS);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
/*
* Return the untagged transaction id for a given target/channel lun.
*/
u_int
ahd_find_busy_tcl(struct ahd_softc *ahd, u_int tcl)
{
u_int scbid;
u_int scb_offset;
u_int saved_scbptr;
scb_offset = ahd_index_busy_tcl(ahd, &saved_scbptr, tcl);
scbid = ahd_inw_scbram(ahd, scb_offset);
ahd_set_scbptr(ahd, saved_scbptr);
return (scbid);
}
void
ahd_busy_tcl(struct ahd_softc *ahd, u_int tcl, u_int scbid)
{
u_int scb_offset;
u_int saved_scbptr;
scb_offset = ahd_index_busy_tcl(ahd, &saved_scbptr, tcl);
ahd_outw(ahd, scb_offset, scbid);
ahd_set_scbptr(ahd, saved_scbptr);
}
/************************** SCB and SCB queue management **********************/
int
ahd_match_scb(struct ahd_softc *ahd, struct scb *scb, int target,
char channel, int lun, u_int tag, role_t role)
{
int targ = SCB_GET_TARGET(ahd, scb);
char chan = SCB_GET_CHANNEL(ahd, scb);
int slun = SCB_GET_LUN(scb);
int match;
match = ((chan == channel) || (channel == ALL_CHANNELS));
if (match != 0)
match = ((targ == target) || (target == CAM_TARGET_WILDCARD));
if (match != 0)
match = ((lun == slun) || (lun == CAM_LUN_WILDCARD));
if (match != 0) {
#if AHD_TARGET_MODE
int group;
group = XPT_FC_GROUP(scb->io_ctx->ccb_h.func_code);
if (role == ROLE_INITIATOR) {
match = (group != XPT_FC_GROUP_TMODE)
&& ((tag == SCB_GET_TAG(scb))
|| (tag == SCB_LIST_NULL));
} else if (role == ROLE_TARGET) {
match = (group == XPT_FC_GROUP_TMODE)
&& ((tag == scb->io_ctx->csio.tag_id)
|| (tag == SCB_LIST_NULL));
}
#else /* !AHD_TARGET_MODE */
match = ((tag == SCB_GET_TAG(scb)) || (tag == SCB_LIST_NULL));
#endif /* AHD_TARGET_MODE */
}
return match;
}
void
ahd_freeze_devq(struct ahd_softc *ahd, struct scb *scb)
{
int target;
char channel;
int lun;
target = SCB_GET_TARGET(ahd, scb);
lun = SCB_GET_LUN(scb);
channel = SCB_GET_CHANNEL(ahd, scb);
ahd_search_qinfifo(ahd, target, channel, lun,
/*tag*/SCB_LIST_NULL, ROLE_UNKNOWN,
CAM_REQUEUE_REQ, SEARCH_COMPLETE);
ahd_platform_freeze_devq(ahd, scb);
}
void
ahd_qinfifo_requeue_tail(struct ahd_softc *ahd, struct scb *scb)
{
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
struct scb *prev_scb;
ahd_mode_state saved_modes;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
saved_modes = ahd_save_modes(ahd);
ahd_set_modes(ahd, AHD_MODE_CCHAN, AHD_MODE_CCHAN);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
prev_scb = NULL;
if (ahd_qinfifo_count(ahd) != 0) {
u_int prev_tag;
u_int prev_pos;
prev_pos = AHD_QIN_WRAP(ahd->qinfifonext - 1);
prev_tag = ahd->qinfifo[prev_pos];
prev_scb = ahd_lookup_scb(ahd, prev_tag);
}
ahd_qinfifo_requeue(ahd, prev_scb, scb);
ahd_set_hnscb_qoff(ahd, ahd->qinfifonext);
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
ahd_restore_modes(ahd, saved_modes);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
static void
ahd_qinfifo_requeue(struct ahd_softc *ahd, struct scb *prev_scb,
struct scb *scb)
{
if (prev_scb == NULL) {
uint32_t busaddr;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
busaddr = aic_le32toh(scb->hscb->hscb_busaddr);
ahd_outl(ahd, NEXT_QUEUED_SCB_ADDR, busaddr);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
} else {
prev_scb->hscb->next_hscb_busaddr = scb->hscb->hscb_busaddr;
ahd_sync_scb(ahd, prev_scb,
BUS_DMASYNC_PREREAD|BUS_DMASYNC_PREWRITE);
}
ahd->qinfifo[AHD_QIN_WRAP(ahd->qinfifonext)] = SCB_GET_TAG(scb);
ahd->qinfifonext++;
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
scb->hscb->next_hscb_busaddr = ahd->next_queued_hscb->hscb_busaddr;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_sync_scb(ahd, scb, BUS_DMASYNC_PREREAD|BUS_DMASYNC_PREWRITE);
}
static int
ahd_qinfifo_count(struct ahd_softc *ahd)
{
u_int qinpos;
u_int wrap_qinpos;
u_int wrap_qinfifonext;
AHD_ASSERT_MODES(ahd, AHD_MODE_CCHAN_MSK, AHD_MODE_CCHAN_MSK);
qinpos = ahd_get_snscb_qoff(ahd);
wrap_qinpos = AHD_QIN_WRAP(qinpos);
wrap_qinfifonext = AHD_QIN_WRAP(ahd->qinfifonext);
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
if (wrap_qinfifonext >= wrap_qinpos)
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
return (wrap_qinfifonext - wrap_qinpos);
else
return (wrap_qinfifonext
+ NUM_ELEMENTS(ahd->qinfifo) - wrap_qinpos);
}
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
void
ahd_reset_cmds_pending(struct ahd_softc *ahd)
{
struct scb *scb;
ahd_mode_state saved_modes;
u_int pending_cmds;
saved_modes = ahd_save_modes(ahd);
ahd_set_modes(ahd, AHD_MODE_CCHAN, AHD_MODE_CCHAN);
/*
* Don't count any commands as outstanding that the
* sequencer has already marked for completion.
*/
ahd_flush_qoutfifo(ahd);
pending_cmds = 0;
LIST_FOREACH(scb, &ahd->pending_scbs, pending_links) {
pending_cmds++;
}
ahd_outw(ahd, CMDS_PENDING, pending_cmds - ahd_qinfifo_count(ahd));
ahd_restore_modes(ahd, saved_modes);
ahd->flags &= ~AHD_UPDATE_PEND_CMDS;
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
int
ahd_search_qinfifo(struct ahd_softc *ahd, int target, char channel,
int lun, u_int tag, role_t role, uint32_t status,
ahd_search_action action)
{
struct scb *scb;
struct scb *prev_scb;
ahd_mode_state saved_modes;
u_int qinstart;
u_int qinpos;
u_int qintail;
u_int tid_next;
u_int tid_prev;
u_int scbid;
u_int savedscbptr;
uint32_t busaddr;
int found;
int targets;
/* Must be in CCHAN mode */
saved_modes = ahd_save_modes(ahd);
ahd_set_modes(ahd, AHD_MODE_CCHAN, AHD_MODE_CCHAN);
/*
* Halt any pending SCB DMA. The sequencer will reinitiate
* this dma if the qinfifo is not empty once we unpause.
*/
if ((ahd_inb(ahd, CCSCBCTL) & (CCARREN|CCSCBEN|CCSCBDIR))
== (CCARREN|CCSCBEN|CCSCBDIR)) {
ahd_outb(ahd, CCSCBCTL,
ahd_inb(ahd, CCSCBCTL) & ~(CCARREN|CCSCBEN));
while ((ahd_inb(ahd, CCSCBCTL) & (CCARREN|CCSCBEN)) != 0)
;
}
/* Determine sequencer's position in the qinfifo. */
qintail = AHD_QIN_WRAP(ahd->qinfifonext);
qinstart = ahd_get_snscb_qoff(ahd);
qinpos = AHD_QIN_WRAP(qinstart);
found = 0;
prev_scb = NULL;
if (action == SEARCH_PRINT) {
printf("qinstart = %d qinfifonext = %d\nQINFIFO:",
qinstart, ahd->qinfifonext);
}
/*
* Start with an empty queue. Entries that are not chosen
* for removal will be re-added to the queue as we go.
*/
ahd->qinfifonext = qinstart;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
busaddr = aic_le32toh(ahd->next_queued_hscb->hscb_busaddr);
ahd_outl(ahd, NEXT_QUEUED_SCB_ADDR, busaddr);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
while (qinpos != qintail) {
scb = ahd_lookup_scb(ahd, ahd->qinfifo[qinpos]);
if (scb == NULL) {
printf("qinpos = %d, SCB index = %d\n",
qinpos, ahd->qinfifo[qinpos]);
panic("Loop 1\n");
}
if (ahd_match_scb(ahd, scb, target, channel, lun, tag, role)) {
/*
* We found an scb that needs to be acted on.
*/
found++;
switch (action) {
case SEARCH_COMPLETE:
{
cam_status ostat;
cam_status cstat;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
ostat = aic_get_transaction_status(scb);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if (ostat == CAM_REQ_INPROG)
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_set_transaction_status(scb,
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
status);
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
cstat = aic_get_transaction_status(scb);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if (cstat != CAM_REQ_CMP)
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_freeze_scb(scb);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if ((scb->flags & SCB_ACTIVE) == 0)
printf("Inactive SCB in qinfifo\n");
ahd_done(ahd, scb);
/* FALLTHROUGH */
}
case SEARCH_REMOVE:
break;
case SEARCH_PRINT:
printf(" 0x%x", ahd->qinfifo[qinpos]);
/* FALLTHROUGH */
case SEARCH_COUNT:
ahd_qinfifo_requeue(ahd, prev_scb, scb);
prev_scb = scb;
break;
}
} else {
ahd_qinfifo_requeue(ahd, prev_scb, scb);
prev_scb = scb;
}
qinpos = AHD_QIN_WRAP(qinpos+1);
}
ahd_set_hnscb_qoff(ahd, ahd->qinfifonext);
if (action == SEARCH_PRINT)
printf("\nWAITING_TID_QUEUES:\n");
/*
* Search waiting for selection lists. We traverse the
* list of "their ids" waiting for selection and, if
* appropriate, traverse the SCBs of each "their id"
* looking for matches.
*/
savedscbptr = ahd_get_scbptr(ahd);
tid_next = ahd_inw(ahd, WAITING_TID_HEAD);
tid_prev = SCB_LIST_NULL;
targets = 0;
for (scbid = tid_next; !SCBID_IS_NULL(scbid); scbid = tid_next) {
u_int tid_head;
/*
* We limit based on the number of SCBs since
* MK_MESSAGE SCBs are not in the per-tid lists.
*/
targets++;
if (targets > AHD_SCB_MAX) {
panic("TID LIST LOOP");
}
if (scbid >= ahd->scb_data.numscbs) {
printf("%s: Waiting TID List inconsistency. "
"SCB index == 0x%x, yet numscbs == 0x%x.",
ahd_name(ahd), scbid, ahd->scb_data.numscbs);
ahd_dump_card_state(ahd);
panic("for safety");
}
scb = ahd_lookup_scb(ahd, scbid);
if (scb == NULL) {
printf("%s: SCB = 0x%x Not Active!\n",
ahd_name(ahd), scbid);
panic("Waiting TID List traversal\n");
}
ahd_set_scbptr(ahd, scbid);
tid_next = ahd_inw_scbram(ahd, SCB_NEXT2);
if (ahd_match_scb(ahd, scb, target, channel, CAM_LUN_WILDCARD,
SCB_LIST_NULL, ROLE_UNKNOWN) == 0) {
tid_prev = scbid;
continue;
}
/*
* We found a list of scbs that needs to be searched.
*/
if (action == SEARCH_PRINT)
printf(" %d ( ", SCB_GET_TARGET(ahd, scb));
tid_head = scbid;
found += ahd_search_scb_list(ahd, target, channel,
lun, tag, role, status,
action, &tid_head,
SCB_GET_TARGET(ahd, scb));
if (tid_head != scbid)
ahd_stitch_tid_list(ahd, tid_prev, tid_head, tid_next);
if (!SCBID_IS_NULL(tid_head))
tid_prev = tid_head;
if (action == SEARCH_PRINT)
printf(")\n");
}
ahd_set_scbptr(ahd, savedscbptr);
ahd_restore_modes(ahd, saved_modes);
return (found);
}
static int
ahd_search_scb_list(struct ahd_softc *ahd, int target, char channel,
int lun, u_int tag, role_t role, uint32_t status,
ahd_search_action action, u_int *list_head, u_int tid)
{
struct scb *scb;
u_int scbid;
u_int next;
u_int prev;
int found;
AHD_ASSERT_MODES(ahd, AHD_MODE_CCHAN_MSK, AHD_MODE_CCHAN_MSK);
found = 0;
prev = SCB_LIST_NULL;
next = *list_head;
for (scbid = next; !SCBID_IS_NULL(scbid); scbid = next) {
if (scbid >= ahd->scb_data.numscbs) {
printf("%s:SCB List inconsistency. "
"SCB == 0x%x, yet numscbs == 0x%x.",
ahd_name(ahd), scbid, ahd->scb_data.numscbs);
ahd_dump_card_state(ahd);
panic("for safety");
}
scb = ahd_lookup_scb(ahd, scbid);
if (scb == NULL) {
printf("%s: SCB = %d Not Active!\n",
ahd_name(ahd), scbid);
panic("Waiting List traversal\n");
}
ahd_set_scbptr(ahd, scbid);
next = ahd_inw_scbram(ahd, SCB_NEXT);
if (ahd_match_scb(ahd, scb, target, channel,
lun, SCB_LIST_NULL, role) == 0) {
prev = scbid;
continue;
}
found++;
switch (action) {
case SEARCH_COMPLETE:
{
cam_status ostat;
cam_status cstat;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
ostat = aic_get_transaction_status(scb);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if (ostat == CAM_REQ_INPROG)
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_set_transaction_status(scb, status);
cstat = aic_get_transaction_status(scb);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if (cstat != CAM_REQ_CMP)
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_freeze_scb(scb);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if ((scb->flags & SCB_ACTIVE) == 0)
printf("Inactive SCB in Waiting List\n");
ahd_done(ahd, scb);
/* FALLTHROUGH */
}
case SEARCH_REMOVE:
ahd_rem_wscb(ahd, scbid, prev, next, tid);
if (prev == SCB_LIST_NULL)
*list_head = next;
break;
case SEARCH_PRINT:
printf("0x%x ", scbid);
case SEARCH_COUNT:
prev = scbid;
break;
}
if (found > AHD_SCB_MAX)
panic("SCB LIST LOOP");
}
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
if (action == SEARCH_COMPLETE
|| action == SEARCH_REMOVE)
ahd_outw(ahd, CMDS_PENDING, ahd_inw(ahd, CMDS_PENDING) - found);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
return (found);
}
static void
ahd_stitch_tid_list(struct ahd_softc *ahd, u_int tid_prev,
u_int tid_cur, u_int tid_next)
{
AHD_ASSERT_MODES(ahd, AHD_MODE_CCHAN_MSK, AHD_MODE_CCHAN_MSK);
if (SCBID_IS_NULL(tid_cur)) {
/* Bypass current TID list */
if (SCBID_IS_NULL(tid_prev)) {
ahd_outw(ahd, WAITING_TID_HEAD, tid_next);
} else {
ahd_set_scbptr(ahd, tid_prev);
ahd_outw(ahd, SCB_NEXT2, tid_next);
}
if (SCBID_IS_NULL(tid_next))
ahd_outw(ahd, WAITING_TID_TAIL, tid_prev);
} else {
/* Stitch through tid_cur */
if (SCBID_IS_NULL(tid_prev)) {
ahd_outw(ahd, WAITING_TID_HEAD, tid_cur);
} else {
ahd_set_scbptr(ahd, tid_prev);
ahd_outw(ahd, SCB_NEXT2, tid_cur);
}
ahd_set_scbptr(ahd, tid_cur);
ahd_outw(ahd, SCB_NEXT2, tid_next);
if (SCBID_IS_NULL(tid_next))
ahd_outw(ahd, WAITING_TID_TAIL, tid_cur);
}
}
/*
* Manipulate the waiting for selection list and return the
* scb that follows the one that we remove.
*/
static u_int
ahd_rem_wscb(struct ahd_softc *ahd, u_int scbid,
u_int prev, u_int next, u_int tid)
{
u_int tail_offset;
AHD_ASSERT_MODES(ahd, AHD_MODE_CCHAN_MSK, AHD_MODE_CCHAN_MSK);
if (!SCBID_IS_NULL(prev)) {
ahd_set_scbptr(ahd, prev);
ahd_outw(ahd, SCB_NEXT, next);
}
/*
* SCBs that had MK_MESSAGE set in them will not
* be queued to the per-target lists, so don't
* blindly clear the tail pointer.
*/
tail_offset = WAITING_SCB_TAILS + (2 * tid);
if (SCBID_IS_NULL(next)
&& ahd_inw(ahd, tail_offset) == scbid)
ahd_outw(ahd, tail_offset, prev);
ahd_add_scb_to_free_list(ahd, scbid);
return (next);
}
/*
* Add the SCB as selected by SCBPTR onto the on chip list of
* free hardware SCBs. This list is empty/unused if we are not
* performing SCB paging.
*/
static void
ahd_add_scb_to_free_list(struct ahd_softc *ahd, u_int scbid)
{
/* XXX Need some other mechanism to designate "free". */
/*
* Invalidate the tag so that our abort
* routines don't think it's active.
ahd_outb(ahd, SCB_TAG, SCB_LIST_NULL);
*/
}
/******************************** Error Handling ******************************/
/*
* Abort all SCBs that match the given description (target/channel/lun/tag),
* setting their status to the passed in status if the status has not already
* been modified from CAM_REQ_INPROG. This routine assumes that the sequencer
* is paused before it is called.
*/
int
ahd_abort_scbs(struct ahd_softc *ahd, int target, char channel,
int lun, u_int tag, role_t role, uint32_t status)
{
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
struct scb *scbp;
struct scb *scbp_next;
u_int i, j;
u_int maxtarget;
u_int minlun;
u_int maxlun;
int found;
ahd_mode_state saved_modes;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
/* restore this when we're done */
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
saved_modes = ahd_save_modes(ahd);
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
found = ahd_search_qinfifo(ahd, target, channel, lun, SCB_LIST_NULL,
role, CAM_REQUEUE_REQ, SEARCH_COMPLETE);
/*
* Clean out the busy target table for any untagged commands.
*/
i = 0;
maxtarget = 16;
if (target != CAM_TARGET_WILDCARD) {
i = target;
if (channel == 'B')
i += 8;
maxtarget = i + 1;
}
if (lun == CAM_LUN_WILDCARD) {
minlun = 0;
maxlun = AHD_NUM_LUNS_NONPKT;
} else if (lun >= AHD_NUM_LUNS_NONPKT) {
minlun = maxlun = 0;
} else {
minlun = lun;
maxlun = lun + 1;
}
if (role != ROLE_TARGET) {
for (;i < maxtarget; i++) {
for (j = minlun;j < maxlun; j++) {
u_int scbid;
u_int tcl;
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
tcl = BUILD_TCL_RAW(i, 'A', j);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
scbid = ahd_find_busy_tcl(ahd, tcl);
scbp = ahd_lookup_scb(ahd, scbid);
if (scbp == NULL
|| ahd_match_scb(ahd, scbp, target, channel,
lun, tag, role) == 0)
continue;
ahd_unbusy_tcl(ahd, BUILD_TCL_RAW(i, 'A', j));
}
}
}
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
/*
* Don't abort commands that have already completed,
* but haven't quite made it up to the host yet.
*/
ahd_flush_qoutfifo(ahd);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*
* Go through the pending CCB list and look for
* commands for this target that are still active.
* These are other tagged commands that were
* disconnected when the reset occurred.
*/
scbp_next = LIST_FIRST(&ahd->pending_scbs);
while (scbp_next != NULL) {
scbp = scbp_next;
scbp_next = LIST_NEXT(scbp, pending_links);
if (ahd_match_scb(ahd, scbp, target, channel, lun, tag, role)) {
cam_status ostat;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
ostat = aic_get_transaction_status(scbp);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if (ostat == CAM_REQ_INPROG)
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_set_transaction_status(scbp, status);
if (aic_get_transaction_status(scbp) != CAM_REQ_CMP)
aic_freeze_scb(scbp);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if ((scbp->flags & SCB_ACTIVE) == 0)
printf("Inactive SCB on pending list\n");
ahd_done(ahd, scbp);
found++;
}
}
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
ahd_restore_modes(ahd, saved_modes);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_platform_abort_scbs(ahd, target, channel, lun, tag, role, status);
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
ahd->flags |= AHD_UPDATE_PEND_CMDS;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
return found;
}
static void
ahd_reset_current_bus(struct ahd_softc *ahd)
{
uint8_t scsiseq;
AHD_ASSERT_MODES(ahd, AHD_MODE_SCSI_MSK, AHD_MODE_SCSI_MSK);
ahd_outb(ahd, SIMODE1, ahd_inb(ahd, SIMODE1) & ~ENSCSIRST);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
scsiseq = ahd_inb(ahd, SCSISEQ0) & ~(ENSELO|ENARBO|SCSIRSTO);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_outb(ahd, SCSISEQ0, scsiseq | SCSIRSTO);
Correct a typo in a comment. Add a comment in ahd_clear_critical_sections() about our need to leave ENBUSFREE set in SIMODE1 while single stepping. Re-arrange some delay loops so that we always perform a read after any register write and before the delay. This should make the delay loop more accurate. When completing message processing for a packetized commention, return the controller to a state where invalid non-packetized phases will still cause protocol violations. These are the same operations as those performed in the clear_target_state routine in the firmware. Now that we have a chip with working ABORTPENDING support (the 7901B), comment out the automatic use of this feature until we can adequately test it. The previous checkin updated the bug mask for the 7901B so this code was exercised. When resetting the bus, perform an ahd_flush_device_writes() call so that our reset assertion delay is acurately timed from when the reset bit is written to the controller.
2003-06-28 04:42:11 +00:00
ahd_flush_device_writes(ahd);
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_delay(AHD_BUSRESET_DELAY);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/* Turn off the bus reset */
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
ahd_outb(ahd, SCSISEQ0, scsiseq);
Correct a typo in a comment. Add a comment in ahd_clear_critical_sections() about our need to leave ENBUSFREE set in SIMODE1 while single stepping. Re-arrange some delay loops so that we always perform a read after any register write and before the delay. This should make the delay loop more accurate. When completing message processing for a packetized commention, return the controller to a state where invalid non-packetized phases will still cause protocol violations. These are the same operations as those performed in the clear_target_state routine in the firmware. Now that we have a chip with working ABORTPENDING support (the 7901B), comment out the automatic use of this feature until we can adequately test it. The previous checkin updated the bug mask for the 7901B so this code was exercised. When resetting the bus, perform an ahd_flush_device_writes() call so that our reset assertion delay is acurately timed from when the reset bit is written to the controller.
2003-06-28 04:42:11 +00:00
ahd_flush_device_writes(ahd);
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_delay(AHD_BUSRESET_DELAY);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if ((ahd->bugs & AHD_SCSIRST_BUG) != 0) {
/*
* 2A Razor #474
* Certain chip state is not cleared for
* SCSI bus resets that we initiate, so
* we must reset the chip.
*/
aic7770.c: aic79xx.c: aic79xx.h: aic79xx_pci.c: aic7xxx.c: aic7xxx.h: aic7xxx_pci.c: Switch ah?_reset() to take an additional "reinit" argument. Use this instead of init_level to determin if the chip should be fully reinitialized after a chip reset. This is required so that ah?_shutdown() can reset the chip without side-effects. aic79xx.c: Implement ahd_suspend() and ahd_resume(). aic7xxx.c: Change ahc_loadseq() to *not* restart the sequencer. This brings the loadseq behavior in line with that of the 7902 driver and also simplifies the init routine. Correct the resume routine to enable interrupts and restart the sequencer.
2003-06-06 23:48:19 +00:00
ahd_reset(ahd, /*reinit*/TRUE);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_intr_enable(ahd, /*enable*/TRUE);
AHD_ASSERT_MODES(ahd, AHD_MODE_SCSI_MSK, AHD_MODE_SCSI_MSK);
}
ahd_clear_intstat(ahd);
}
int
ahd_reset_channel(struct ahd_softc *ahd, char channel, int initiate_reset)
{
struct ahd_devinfo devinfo;
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
u_int initiator;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
u_int target;
u_int max_scsiid;
int found;
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
u_int fifo;
u_int next_fifo;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd->pending_device = NULL;
ahd_compile_devinfo(&devinfo,
CAM_TARGET_WILDCARD,
CAM_TARGET_WILDCARD,
CAM_LUN_WILDCARD,
channel, ROLE_UNKNOWN);
ahd_pause(ahd);
/* Make sure the sequencer is in a safe location. */
ahd_clear_critical_section(ahd);
#if AHD_TARGET_MODE
if ((ahd->flags & AHD_TARGETROLE) != 0) {
ahd_run_tqinfifo(ahd, /*paused*/TRUE);
}
#endif
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
/*
* Disable selections so no automatic hardware
* functions will modify chip state.
*/
ahd_outb(ahd, SCSISEQ0, 0);
ahd_outb(ahd, SCSISEQ1, 0);
/*
* Safely shut down our DMA engines. Always start with
* the FIFO that is not currently active (if any are
* actively connected).
*/
next_fifo = fifo = ahd_inb(ahd, DFFSTAT) & CURRFIFO;
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
if (next_fifo > CURRFIFO_1)
/* If disconneced, arbitrarily start with FIFO1. */
next_fifo = fifo = 0;
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
do {
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
next_fifo ^= CURRFIFO_1;
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
ahd_set_modes(ahd, next_fifo, next_fifo);
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
ahd_outb(ahd, DFCNTRL,
ahd_inb(ahd, DFCNTRL) & ~(SCSIEN|HDMAEN));
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
while ((ahd_inb(ahd, DFCNTRL) & HDMAENACK) != 0)
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_delay(10);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
/*
* Set CURRFIFO to the now inactive channel.
*/
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
ahd_outb(ahd, DFFSTAT, next_fifo);
} while (next_fifo != fifo);
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*
* Reset the bus if we are initiating this reset
*/
ahd_clear_msg_state(ahd);
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
ahd_outb(ahd, SIMODE1,
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
ahd_inb(ahd, SIMODE1) & ~(ENBUSFREE|ENSCSIRST));
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if (initiate_reset)
ahd_reset_current_bus(ahd);
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_clear_intstat(ahd);
/*
* Clean up all the state information for the
* pending transactions on this bus.
*/
found = ahd_abort_scbs(ahd, CAM_TARGET_WILDCARD, channel,
CAM_LUN_WILDCARD, SCB_LIST_NULL,
ROLE_UNKNOWN, CAM_SCSI_BUS_RESET);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
/*
* Cleanup anything left in the FIFOs.
*/
ahd_clear_fifo(ahd, 0);
ahd_clear_fifo(ahd, 1);
/*
* Revert to async/narrow transfers until we renegotiate.
*/
max_scsiid = (ahd->features & AHD_WIDE) ? 15 : 7;
for (target = 0; target <= max_scsiid; target++) {
if (ahd->enabled_targets[target] == NULL)
continue;
for (initiator = 0; initiator <= max_scsiid; initiator++) {
struct ahd_devinfo devinfo;
ahd_compile_devinfo(&devinfo, target, initiator,
CAM_LUN_WILDCARD,
'A', ROLE_UNKNOWN);
ahd_set_width(ahd, &devinfo, MSG_EXT_WDTR_BUS_8_BIT,
AHD_TRANS_CUR, /*paused*/TRUE);
ahd_set_syncrate(ahd, &devinfo, /*period*/0,
/*offset*/0, /*ppr_options*/0,
AHD_TRANS_CUR, /*paused*/TRUE);
}
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
#ifdef AHD_TARGET_MODE
max_scsiid = (ahd->features & AHD_WIDE) ? 15 : 7;
/*
* Send an immediate notify ccb to all target more peripheral
* drivers affected by this action.
*/
for (target = 0; target <= max_scsiid; target++) {
struct ahd_tmode_tstate* tstate;
u_int lun;
tstate = ahd->enabled_targets[target];
if (tstate == NULL)
continue;
for (lun = 0; lun < AHD_NUM_LUNS; lun++) {
struct ahd_tmode_lstate* lstate;
lstate = tstate->enabled_luns[lun];
if (lstate == NULL)
continue;
ahd_queue_lstate_event(ahd, lstate, CAM_TARGET_WILDCARD,
EVENT_TYPE_BUS_RESET, /*arg*/0);
ahd_send_lstate_events(ahd, lstate);
}
}
#endif
/* Notify the XPT that a bus reset occurred */
ahd_send_async(ahd, devinfo.channel, CAM_TARGET_WILDCARD,
CAM_LUN_WILDCARD, AC_BUS_RESET, NULL);
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
ahd_restart(ahd);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*
* Freeze the SIMQ until our poller can determine that
* the bus reset has really gone away. We set the initial
* timer to 0 to have the check performed as soon as possible
* from the timer context.
*/
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
if ((ahd->flags & AHD_RESET_POLL_ACTIVE) == 0) {
ahd->flags |= AHD_RESET_POLL_ACTIVE;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_freeze_simq(ahd);
aic_timer_reset(&ahd->reset_timer, 0, ahd_reset_poll, ahd);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
return (found);
}
#define AHD_RESET_POLL_US 1000
static void
ahd_reset_poll(void *arg)
{
struct ahd_softc *ahd;
u_int scsiseq1;
u_long l;
u_long s;
ahd_list_lock(&l);
ahd = ahd_find_softc((struct ahd_softc *)arg);
if (ahd == NULL) {
printf("ahd_reset_poll: Instance %p no longer exists\n", arg);
ahd_list_unlock(&l);
return;
}
ahd_lock(ahd, &s);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
ahd_pause(ahd);
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
ahd_update_modes(ahd);
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
ahd_outb(ahd, CLRSINT1, CLRSCSIRSTI);
if ((ahd_inb(ahd, SSTAT1) & SCSIRSTI) != 0) {
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_timer_reset(&ahd->reset_timer, AHD_RESET_POLL_US,
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_reset_poll, ahd);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
ahd_unpause(ahd);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_unlock(ahd, &s);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
ahd_list_unlock(&l);
return;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
/* Reset is now low. Complete chip reinitialization. */
ahd_outb(ahd, SIMODE1, ahd_inb(ahd, SIMODE1) | ENSCSIRST);
scsiseq1 = ahd_inb(ahd, SCSISEQ_TEMPLATE);
ahd_outb(ahd, SCSISEQ1, scsiseq1 & (ENSELI|ENRSELI|ENAUTOATNP));
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
ahd_unpause(ahd);
ahd->flags &= ~AHD_RESET_POLL_ACTIVE;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_unlock(ahd, &s);
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_release_simq(ahd);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_list_unlock(&l);
}
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
/**************************** Statistics Processing ***************************/
static void
ahd_stat_timer(void *arg)
{
struct ahd_softc *ahd;
u_long l;
u_long s;
int enint_coal;
ahd_list_lock(&l);
ahd = ahd_find_softc((struct ahd_softc *)arg);
if (ahd == NULL) {
printf("ahd_stat_timer: Instance %p no longer exists\n", arg);
ahd_list_unlock(&l);
return;
}
ahd_lock(ahd, &s);
Fixup spelling of "coalesce" and derivatives. Approved by: RE
2003-05-26 21:10:58 +00:00
enint_coal = ahd->hs_mailbox & ENINT_COALESCE;
if (ahd->cmdcmplt_total > ahd->int_coalescing_threshold)
enint_coal |= ENINT_COALESCE;
else if (ahd->cmdcmplt_total < ahd->int_coalescing_stop_threshold)
enint_coal &= ~ENINT_COALESCE;
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
Fixup spelling of "coalesce" and derivatives. Approved by: RE
2003-05-26 21:10:58 +00:00
if (enint_coal != (ahd->hs_mailbox & ENINT_COALESCE)) {
ahd_enable_coalescing(ahd, enint_coal);
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
#ifdef AHD_DEBUG
Fixup spelling of "coalesce" and derivatives. Approved by: RE
2003-05-26 21:10:58 +00:00
if ((ahd_debug & AHD_SHOW_INT_COALESCING) != 0)
printf("%s: Interrupt coalescing "
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
"now %sabled. Cmds %d\n",
ahd_name(ahd),
Fixup spelling of "coalesce" and derivatives. Approved by: RE
2003-05-26 21:10:58 +00:00
(enint_coal & ENINT_COALESCE) ? "en" : "dis",
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
ahd->cmdcmplt_total);
#endif
}
ahd->cmdcmplt_bucket = (ahd->cmdcmplt_bucket+1) & (AHD_STAT_BUCKETS-1);
ahd->cmdcmplt_total -= ahd->cmdcmplt_counts[ahd->cmdcmplt_bucket];
ahd->cmdcmplt_counts[ahd->cmdcmplt_bucket] = 0;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_timer_reset(&ahd->stat_timer, AHD_STAT_UPDATE_US,
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
ahd_stat_timer, ahd);
ahd_unlock(ahd, &s);
ahd_list_unlock(&l);
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/****************************** Status Processing *****************************/
void
ahd_handle_scb_status(struct ahd_softc *ahd, struct scb *scb)
{
if (scb->hscb->shared_data.istatus.scsi_status != 0) {
ahd_handle_scsi_status(ahd, scb);
} else {
ahd_calc_residual(ahd, scb);
ahd_done(ahd, scb);
}
}
void
ahd_handle_scsi_status(struct ahd_softc *ahd, struct scb *scb)
{
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
struct hardware_scb *hscb;
u_int qfreeze_cnt;
int paused;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*
* The sequencer freezes its select-out queue
* anytime a SCSI status error occurs. We must
* handle the error and decrement the QFREEZE count
* to allow the sequencer to continue.
*/
hscb = scb->hscb;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
if (ahd_is_paused(ahd)) {
paused = 1;
} else {
paused = 0;
ahd_pause(ahd);
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/* Freeze the queue until the client sees the error. */
ahd_freeze_devq(ahd, scb);
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_freeze_scb(scb);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
qfreeze_cnt = ahd_inw(ahd, QFREEZE_COUNT);
if (qfreeze_cnt == 0) {
printf("%s: Bad status with 0 qfreeze count!\n", ahd_name(ahd));
} else {
qfreeze_cnt--;
ahd_outw(ahd, QFREEZE_COUNT, qfreeze_cnt);
}
if (qfreeze_cnt == 0)
ahd_outb(ahd, SEQ_FLAGS2,
ahd_inb(ahd, SEQ_FLAGS2) & ~SELECTOUT_QFROZEN);
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
if (paused == 0)
ahd_unpause(ahd);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
/* Don't want to clobber the original sense code */
if ((scb->flags & SCB_SENSE) != 0) {
/*
* Clear the SCB_SENSE Flag and perform
* a normal command completion.
*/
scb->flags &= ~SCB_SENSE;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_set_transaction_status(scb, CAM_AUTOSENSE_FAIL);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
ahd_done(ahd, scb);
return;
}
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_set_transaction_status(scb, CAM_SCSI_STATUS_ERROR);
aic_set_scsi_status(scb, hscb->shared_data.istatus.scsi_status);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
switch (hscb->shared_data.istatus.scsi_status) {
case STATUS_PKT_SENSE:
{
struct scsi_status_iu_header *siu;
ahd_sync_sense(ahd, scb, BUS_DMASYNC_POSTREAD);
siu = (struct scsi_status_iu_header *)scb->sense_data;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_set_scsi_status(scb, siu->status);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
#ifdef AHD_DEBUG
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
if ((ahd_debug & AHD_SHOW_SENSE) != 0) {
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_print_path(ahd, scb);
printf("SCB 0x%x Received PKT Status of 0x%x\n",
SCB_GET_TAG(scb), siu->status);
printf("\tflags = 0x%x, sense len = 0x%x, "
"pktfail = 0x%x\n",
siu->flags, scsi_4btoul(siu->sense_length),
scsi_4btoul(siu->pkt_failures_length));
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
#endif
if ((siu->flags & SIU_RSPVALID) != 0) {
ahd_print_path(ahd, scb);
if (scsi_4btoul(siu->pkt_failures_length) < 4) {
printf("Unable to parse pkt_failures\n");
} else {
switch (SIU_PKTFAIL_CODE(siu)) {
case SIU_PFC_NONE:
printf("No packet failure found\n");
break;
case SIU_PFC_CIU_FIELDS_INVALID:
printf("Invalid Command IU Field\n");
break;
case SIU_PFC_TMF_NOT_SUPPORTED:
printf("TMF not supportd\n");
break;
case SIU_PFC_TMF_FAILED:
printf("TMF failed\n");
break;
case SIU_PFC_INVALID_TYPE_CODE:
printf("Invalid L_Q Type code\n");
break;
case SIU_PFC_ILLEGAL_REQUEST:
printf("Illegal request\n");
default:
break;
}
}
if (siu->status == SCSI_STATUS_OK)
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_set_transaction_status(scb,
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
CAM_REQ_CMP_ERR);
}
if ((siu->flags & SIU_SNSVALID) != 0) {
scb->flags |= SCB_PKT_SENSE;
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_SENSE) != 0)
printf("Sense data available\n");
#endif
}
ahd_done(ahd, scb);
break;
}
case SCSI_STATUS_CMD_TERMINATED:
case SCSI_STATUS_CHECK_COND:
{
struct ahd_devinfo devinfo;
struct ahd_dma_seg *sg;
struct scsi_sense *sc;
struct ahd_initiator_tinfo *targ_info;
struct ahd_tmode_tstate *tstate;
struct ahd_transinfo *tinfo;
#ifdef AHD_DEBUG
if (ahd_debug & AHD_SHOW_SENSE) {
ahd_print_path(ahd, scb);
printf("SCB %d: requests Check Status\n",
SCB_GET_TAG(scb));
}
#endif
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
if (aic_perform_autosense(scb) == 0)
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
break;
ahd_compile_devinfo(&devinfo, SCB_GET_OUR_ID(scb),
SCB_GET_TARGET(ahd, scb),
SCB_GET_LUN(scb),
SCB_GET_CHANNEL(ahd, scb),
ROLE_INITIATOR);
targ_info = ahd_fetch_transinfo(ahd,
devinfo.channel,
devinfo.our_scsiid,
devinfo.target,
&tstate);
tinfo = &targ_info->curr;
sg = scb->sg_list;
sc = (struct scsi_sense *)hscb->shared_data.idata.cdb;
/*
* Save off the residual if there is one.
*/
ahd_update_residual(ahd, scb);
#ifdef AHD_DEBUG
if (ahd_debug & AHD_SHOW_SENSE) {
ahd_print_path(ahd, scb);
printf("Sending Sense\n");
}
#endif
scb->sg_count = 0;
sg = ahd_sg_setup(ahd, scb, sg, ahd_get_sense_bufaddr(ahd, scb),
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_get_sense_bufsize(ahd, scb),
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/*last*/TRUE);
sc->opcode = REQUEST_SENSE;
sc->byte2 = 0;
if (tinfo->protocol_version <= SCSI_REV_2
&& SCB_GET_LUN(scb) < 8)
sc->byte2 = SCB_GET_LUN(scb) << 5;
sc->unused[0] = 0;
sc->unused[1] = 0;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
sc->length = aic_get_sense_bufsize(ahd, scb);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
sc->control = 0;
/*
* We can't allow the target to disconnect.
* This will be an untagged transaction and
* having the target disconnect will make this
* transaction indestinguishable from outstanding
* tagged transactions.
*/
hscb->control = 0;
/*
* This request sense could be because the
* the device lost power or in some other
* way has lost our transfer negotiations.
* Renegotiate if appropriate. Unit attention
* errors will be reported before any data
* phases occur.
*/
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
if (aic_get_residual(scb) == aic_get_transfer_length(scb)) {
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_update_neg_request(ahd, &devinfo,
tstate, targ_info,
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
AHD_NEG_IF_NON_ASYNC);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
if (tstate->auto_negotiate & devinfo.target_mask) {
hscb->control |= MK_MESSAGE;
scb->flags &=
~(SCB_NEGOTIATE|SCB_ABORT|SCB_DEVICE_RESET);
scb->flags |= SCB_AUTO_NEGOTIATE;
}
hscb->cdb_len = sizeof(*sc);
ahd_setup_data_scb(ahd, scb);
scb->flags |= SCB_SENSE;
ahd_queue_scb(ahd, scb);
/*
* Ensure we have enough time to actually
* retrieve the sense.
*/
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_scb_timer_reset(scb, 5 * 1000000);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
break;
}
case SCSI_STATUS_OK:
printf("%s: Interrupted for staus of 0???\n",
ahd_name(ahd));
/* FALLTHROUGH */
default:
ahd_done(ahd, scb);
break;
}
}
/*
* Calculate the residual for a just completed SCB.
*/
void
ahd_calc_residual(struct ahd_softc *ahd, struct scb *scb)
{
struct hardware_scb *hscb;
struct initiator_status *spkt;
uint32_t sgptr;
uint32_t resid_sgptr;
uint32_t resid;
/*
* 5 cases.
* 1) No residual.
* SG_STATUS_VALID clear in sgptr.
* 2) Transferless command
* 3) Never performed any transfers.
* sgptr has SG_FULL_RESID set.
* 4) No residual but target did not
* save data pointers after the
* last transfer, so sgptr was
* never updated.
* 5) We have a partial residual.
* Use residual_sgptr to determine
* where we are.
*/
hscb = scb->hscb;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
sgptr = aic_le32toh(hscb->sgptr);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if ((sgptr & SG_STATUS_VALID) == 0)
/* Case 1 */
return;
sgptr &= ~SG_STATUS_VALID;
if ((sgptr & SG_LIST_NULL) != 0)
/* Case 2 */
return;
/*
* Residual fields are the same in both
* target and initiator status packets,
* so we can always use the initiator fields
* regardless of the role for this SCB.
*/
spkt = &hscb->shared_data.istatus;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
resid_sgptr = aic_le32toh(spkt->residual_sgptr);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if ((sgptr & SG_FULL_RESID) != 0) {
/* Case 3 */
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
resid = aic_get_transfer_length(scb);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
} else if ((resid_sgptr & SG_LIST_NULL) != 0) {
/* Case 4 */
return;
} else if ((resid_sgptr & SG_OVERRUN_RESID) != 0) {
ahd_print_path(ahd, scb);
printf("data overrun detected Tag == 0x%x.\n",
SCB_GET_TAG(scb));
ahd_freeze_devq(ahd, scb);
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_set_transaction_status(scb, CAM_DATA_RUN_ERR);
aic_freeze_scb(scb);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
return;
} else if ((resid_sgptr & ~SG_PTR_MASK) != 0) {
panic("Bogus resid sgptr value 0x%x\n", resid_sgptr);
/* NOTREACHED */
} else {
struct ahd_dma_seg *sg;
/*
* Remainder of the SG where the transfer
* stopped.
*/
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
resid = aic_le32toh(spkt->residual_datacnt) & AHD_SG_LEN_MASK;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
sg = ahd_sg_bus_to_virt(ahd, scb, resid_sgptr & SG_PTR_MASK);
/* The residual sg_ptr always points to the next sg */
sg--;
/*
* Add up the contents of all residual
* SG segments that are after the SG where
* the transfer stopped.
*/
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
while ((aic_le32toh(sg->len) & AHD_DMA_LAST_SEG) == 0) {
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
sg++;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
resid += aic_le32toh(sg->len) & AHD_SG_LEN_MASK;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
}
if ((scb->flags & SCB_SENSE) == 0)
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_set_residual(scb, resid);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
else
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_set_sense_residual(scb, resid);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_MISC) != 0) {
ahd_print_path(ahd, scb);
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
printf("Handled %sResidual of %d bytes\n",
(scb->flags & SCB_SENSE) ? "Sense " : "", resid);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
#endif
}
/******************************* Target Mode **********************************/
#ifdef AHD_TARGET_MODE
/*
* Add a target mode event to this lun's queue
*/
static void
ahd_queue_lstate_event(struct ahd_softc *ahd, struct ahd_tmode_lstate *lstate,
u_int initiator_id, u_int event_type, u_int event_arg)
{
struct ahd_tmode_event *event;
int pending;
xpt_freeze_devq(lstate->path, /*count*/1);
if (lstate->event_w_idx >= lstate->event_r_idx)
pending = lstate->event_w_idx - lstate->event_r_idx;
else
pending = AHD_TMODE_EVENT_BUFFER_SIZE + 1
- (lstate->event_r_idx - lstate->event_w_idx);
if (event_type == EVENT_TYPE_BUS_RESET
|| event_type == MSG_BUS_DEV_RESET) {
/*
* Any earlier events are irrelevant, so reset our buffer.
* This has the effect of allowing us to deal with reset
* floods (an external device holding down the reset line)
* without losing the event that is really interesting.
*/
lstate->event_r_idx = 0;
lstate->event_w_idx = 0;
xpt_release_devq(lstate->path, pending, /*runqueue*/FALSE);
}
if (pending == AHD_TMODE_EVENT_BUFFER_SIZE) {
xpt_print_path(lstate->path);
printf("immediate event %x:%x lost\n",
lstate->event_buffer[lstate->event_r_idx].event_type,
lstate->event_buffer[lstate->event_r_idx].event_arg);
lstate->event_r_idx++;
if (lstate->event_r_idx == AHD_TMODE_EVENT_BUFFER_SIZE)
lstate->event_r_idx = 0;
xpt_release_devq(lstate->path, /*count*/1, /*runqueue*/FALSE);
}
event = &lstate->event_buffer[lstate->event_w_idx];
event->initiator_id = initiator_id;
event->event_type = event_type;
event->event_arg = event_arg;
lstate->event_w_idx++;
if (lstate->event_w_idx == AHD_TMODE_EVENT_BUFFER_SIZE)
lstate->event_w_idx = 0;
}
/*
* Send any target mode events queued up waiting
* for immediate notify resources.
*/
void
ahd_send_lstate_events(struct ahd_softc *ahd, struct ahd_tmode_lstate *lstate)
{
struct ccb_hdr *ccbh;
struct ccb_immed_notify *inot;
while (lstate->event_r_idx != lstate->event_w_idx
&& (ccbh = SLIST_FIRST(&lstate->immed_notifies)) != NULL) {
struct ahd_tmode_event *event;
event = &lstate->event_buffer[lstate->event_r_idx];
SLIST_REMOVE_HEAD(&lstate->immed_notifies, sim_links.sle);
inot = (struct ccb_immed_notify *)ccbh;
switch (event->event_type) {
case EVENT_TYPE_BUS_RESET:
ccbh->status = CAM_SCSI_BUS_RESET|CAM_DEV_QFRZN;
break;
default:
ccbh->status = CAM_MESSAGE_RECV|CAM_DEV_QFRZN;
inot->message_args[0] = event->event_type;
inot->message_args[1] = event->event_arg;
break;
}
inot->initiator_id = event->initiator_id;
inot->sense_len = 0;
xpt_done((union ccb *)inot);
lstate->event_r_idx++;
if (lstate->event_r_idx == AHD_TMODE_EVENT_BUFFER_SIZE)
lstate->event_r_idx = 0;
}
}
#endif
/******************** Sequencer Program Patching/Download *********************/
#ifdef AHD_DUMP_SEQ
void
ahd_dumpseq(struct ahd_softc* ahd)
{
int i;
int max_prog;
max_prog = 2048;
ahd_outb(ahd, SEQCTL0, PERRORDIS|FAILDIS|FASTMODE|LOADRAM);
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
ahd_outw(ahd, PRGMCNT, 0);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
for (i = 0; i < max_prog; i++) {
uint8_t ins_bytes[4];
ahd_insb(ahd, SEQRAM, ins_bytes, 4);
printf("0x%08x\n", ins_bytes[0] << 24
| ins_bytes[1] << 16
| ins_bytes[2] << 8
| ins_bytes[3]);
}
}
#endif
static void
ahd_loadseq(struct ahd_softc *ahd)
{
struct cs cs_table[num_critical_sections];
u_int begin_set[num_critical_sections];
u_int end_set[num_critical_sections];
struct patch *cur_patch;
u_int cs_count;
u_int cur_cs;
u_int i;
int downloaded;
u_int skip_addr;
u_int sg_prefetch_cnt;
u_int sg_prefetch_cnt_limit;
u_int sg_prefetch_align;
u_int sg_size;
uint8_t download_consts[DOWNLOAD_CONST_COUNT];
if (bootverbose)
printf("%s: Downloading Sequencer Program...",
ahd_name(ahd));
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
#if DOWNLOAD_CONST_COUNT != 7
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
#error "Download Const Mismatch"
#endif
/*
* Start out with 0 critical sections
* that apply to this firmware load.
*/
cs_count = 0;
cur_cs = 0;
memset(begin_set, 0, sizeof(begin_set));
memset(end_set, 0, sizeof(end_set));
/*
* Setup downloadable constant table.
*
* The computation for the S/G prefetch variables is
* a bit complicated. We would like to always fetch
* in terms of cachelined sized increments. However,
* if the cacheline is not an even multiple of the
* SG element size or is larger than our SG RAM, using
* just the cache size might leave us with only a portion
* of an SG element at the tail of a prefetch. If the
* cacheline is larger than our S/G prefetch buffer less
* the size of an SG element, we may round down to a cacheline
* that doesn't contain any or all of the S/G of interest
* within the bounds of our S/G ram. Provide variables to
* the sequencer that will allow it to handle these edge
* cases.
*/
/* Start by aligning to the nearest cacheline. */
sg_prefetch_align = ahd->pci_cachesize;
if (sg_prefetch_align == 0)
aic79xx.c: Clear the LQICRC_NLQ status should it pop up after we have already handled the SCSIPERR. During some streaming operations this status can be delayed until the stream ends. Without this change, the driver would complain about a "Missing case in ahd_handle_scsiint". In the LQOBUSFREE handler... Don't return the LQOMGR back to the idle state until after we have cleaned up ENSELO and any status related to this selection. The last thing we need is the LQO manager starting another select-out before we have updated the execution queue. It is not clear whether the LQOMGR would, or would not start a new selection early. Make sure ENSELO is off prior to clearing SELDO by flushing device writes. Move assignment of the next target SCB pointer inside of an if to make the code clearer. The effect is the same. Dump card state in both "Unexpected PKT busfree" paths. In ahd_reset(), set the chip to SCSI mode before reading SXFRCTL1. That register only exists in the SCSI mode. Also set the mode explicitly to the SCSI mode after chip reset due to paranoia. Re-arrange code so that SXFRCTL1 is restored as quickly after the chip reset as possible. S/G structurs must be 8byte aligned. Make this official by saying so in our DMA tag. Disable CIO bus stretch on MDFFSTAT if SHVALID is about to come true. This can cause a CIO bus lockup if a PCI or PCI-X error occurs while the stretch is occurring - the host cannot service the PCI-X error since the CIO bus is locked out and SHVALID will never resolve. The stretch was added in the Rev B to simplify the wait for SHVALID to resolve, but the code to do this in the open source sequencer is so simple it was never removed. Consistently use MAX_OFFSET for the user max syncrate set from non-volatile storage. This ensures that the offset does not conflict with AH?_OFFSET_UNKNOWN. Have ahd_pause_and_flushwork set the mode to ensure that it has access to the registers it checks. Also modify the checking of intstat so that the check against 0xFF can actually succeed if the INT_PEND mask is something other than 0xFF. Although there are no cardbus U320 controllers, this check may be needed to recover from a hot-plug PCI removal that occurs without informing the driver. Fix a typo. sg_prefetch_cnt -> sg_prefetch_align. This fixes an infinite loop at card initialization if the cacheline size is 0. aic79xx.h: Add AHD_EARLY_REQ_BUG bug flag. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. Change AH?_OFFSET_UNKNOWN to 0xFF. This is a value that the curr->offset can never be, unlike '0' which we previously used. This fixes code that only checks for a non-zero offset to determine if a sync negotiation is required since it will fire in the unknown case even if the goal is async. aic79xx.reg: Add comments for LQISTAT bits indicating their names in the 7902 data book. We use slightly different and more descriptive names in the firmware. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. aic79xx.seq: Update comments regarding rundown of the GSFIFO to reflect reality. Fix spelling errors. Since we use an 8byte address and 1 byte length, shorten the size of a block move for the legacy DMA'ed CDB case from 11 to 9 bytes. Remove code that, assuming the abort pending feature worked, would set MK_MESSAGE in the SCB's control byte on completion to catch invalid reselections. Since we don't see interrupts for completed selections, this status update could occur prior to us noticing the SELDO. The "select-out" queue logic will get confused by the MK_MESSAGE bit being set as this is used to catch packatized connections where we select-out with ATN. Since the abort pending feature doesn't work on any released controllers yet, this code was never executed. Add support for the AHD_EARLY_REQ_BUG. Don't ignore persistent REQ assertions just because they were asserted within the bus settle delay window. This allows us to tolerate devices like the GEM318 that violate the SCSI spec. Remove unintentional settnig of SG_CACHE_AVAIL. Writing this bit should have no effect, but who knows... On the Rev A, we must wait for HDMAENACK before loading additional segments to avoid clobbering the address of the first segment in the S/G FIFO. This resolves data-corruption issues with certain IBM (now Hitachi) and Fujitsu U320 drives. Rearrange calc_residual to avoid an extra jmp instruction. On RevA Silicon, if the target returns us to data-out after we have already trained for data-out, it is possible for us to transition the free running clock to data-valid before the required 100ns P1 setup time (8 P1 assertions in fast-160 mode). This will only happen if this L-Q is a continuation of a data transfer for which we have already prefetched data into our FIFO (LQ/Data followed by LQ/Data for the same write transaction). This can cause some target implementations to miss the first few data transfers on the bus. We detect this situation by noticing that this is the first data transfer after an LQ (LQIWORKONLQ true), that the data transfer is a continuation of a transfer already setup in our FIFO (SAVEPTRS interrupt), and that the transaction is a write (DIRECTION set in DFCNTRL). The delay is performed by disabling SCSIEN until we see the first REQ from the target. Only compile in snapshot savepointers handler for RevA silicon where it is enabled. Handle the cfg4icmd packetized interrupt. We just need to load the address and count, start the DMA, and CLRCHN once the transfer is complete. Fix an oversight in the overrun handler for packetized status operations. We need to wait for either CTXTDONE or an overrun when checking for an overrun. The previous code did not wait and thus could decide that no overrun had occurred even though an overrun will occur on the next data-valid req. Add some comment to this section for clarity. Use LAST_SEG_DONE instead of LASTSDONE for testing transfer completion in the packetized status case. LASTSDONE may come up more quickly since it only records completion on the SCSI side, but since LAST_SEG_DONE is used everywhere else (and needs to be), this is less confusing. Add a missing invalidation of the longjmp address in the non-pack handler. This code needs additional review. aic79xx_inline.h: Fix spelling error. aic79xx_osm.c: Set the cdb length for CDBs dma'ed from host memory. Add a comment indicating that, should CAM start supporting cdbs larger than 16bytes, the driver could store the CDB in the status buffer. aic79xx_pci.c: Add a table entry for the 39320A. Added a missing comma to an error string table. Fix spelling errors.
2003-02-27 23:23:16 +00:00
sg_prefetch_align = 8;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/* Round down to the nearest power of 2. */
while (powerof2(sg_prefetch_align) == 0)
sg_prefetch_align--;
/*
* If the cacheline boundary is greater than half our prefetch RAM
* we risk not being able to fetch even a single complete S/G
* segment if we align to that boundary.
*/
if (sg_prefetch_align > CCSGADDR_MAX/2)
sg_prefetch_align = CCSGADDR_MAX/2;
/* Start by fetching a single cacheline. */
sg_prefetch_cnt = sg_prefetch_align;
/*
* Increment the prefetch count by cachelines until
* at least one S/G element will fit.
*/
sg_size = sizeof(struct ahd_dma_seg);
if ((ahd->flags & AHD_64BIT_ADDRESSING) != 0)
sg_size = sizeof(struct ahd_dma64_seg);
while (sg_prefetch_cnt < sg_size)
sg_prefetch_cnt += sg_prefetch_align;
/*
* If the cacheline is not an even multiple of
* the S/G size, we may only get a partial S/G when
* we align. Add a cacheline if this is the case.
*/
if ((sg_prefetch_align % sg_size) != 0
&& (sg_prefetch_cnt < CCSGADDR_MAX))
sg_prefetch_cnt += sg_prefetch_align;
/*
* Lastly, compute a value that the sequencer can use
* to determine if the remainder of the CCSGRAM buffer
* has a full S/G element in it.
*/
sg_prefetch_cnt_limit = -(sg_prefetch_cnt - sg_size + 1);
download_consts[SG_PREFETCH_CNT] = sg_prefetch_cnt;
download_consts[SG_PREFETCH_CNT_LIMIT] = sg_prefetch_cnt_limit;
download_consts[SG_PREFETCH_ALIGN_MASK] = ~(sg_prefetch_align - 1);
download_consts[SG_PREFETCH_ADDR_MASK] = (sg_prefetch_align - 1);
download_consts[SG_SIZEOF] = sg_size;
download_consts[PKT_OVERRUN_BUFOFFSET] =
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
(ahd->overrun_buf - (uint8_t *)ahd->qoutfifo) / 256;
download_consts[SCB_TRANSFER_SIZE] = SCB_TRANSFER_SIZE_1BYTE_LUN;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
cur_patch = patches;
downloaded = 0;
skip_addr = 0;
ahd_outb(ahd, SEQCTL0, PERRORDIS|FAILDIS|FASTMODE|LOADRAM);
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
ahd_outw(ahd, PRGMCNT, 0);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
for (i = 0; i < sizeof(seqprog)/4; i++) {
if (ahd_check_patch(ahd, &cur_patch, i, &skip_addr) == 0) {
/*
* Don't download this instruction as it
* is in a patch that was removed.
*/
continue;
}
/*
* Move through the CS table until we find a CS
* that might apply to this instruction.
*/
for (; cur_cs < num_critical_sections; cur_cs++) {
if (critical_sections[cur_cs].end <= i) {
if (begin_set[cs_count] == TRUE
&& end_set[cs_count] == FALSE) {
cs_table[cs_count].end = downloaded;
end_set[cs_count] = TRUE;
cs_count++;
}
continue;
}
if (critical_sections[cur_cs].begin <= i
&& begin_set[cs_count] == FALSE) {
cs_table[cs_count].begin = downloaded;
begin_set[cs_count] = TRUE;
}
break;
}
ahd_download_instr(ahd, i, download_consts);
downloaded++;
}
ahd->num_critical_sections = cs_count;
if (cs_count != 0) {
cs_count *= sizeof(struct cs);
ahd->critical_sections = malloc(cs_count, M_DEVBUF, M_NOWAIT);
if (ahd->critical_sections == NULL)
panic("ahd_loadseq: Could not malloc");
memcpy(ahd->critical_sections, cs_table, cs_count);
}
ahd_outb(ahd, SEQCTL0, PERRORDIS|FAILDIS|FASTMODE);
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
if (bootverbose) {
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
printf(" %d instructions downloaded\n", downloaded);
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
printf("%s: Features 0x%x, Bugs 0x%x, Flags 0x%x\n",
ahd_name(ahd), ahd->features, ahd->bugs, ahd->flags);
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
static int
ahd_check_patch(struct ahd_softc *ahd, struct patch **start_patch,
u_int start_instr, u_int *skip_addr)
{
struct patch *cur_patch;
struct patch *last_patch;
u_int num_patches;
num_patches = sizeof(patches)/sizeof(struct patch);
last_patch = &patches[num_patches];
cur_patch = *start_patch;
while (cur_patch < last_patch && start_instr == cur_patch->begin) {
if (cur_patch->patch_func(ahd) == 0) {
/* Start rejecting code */
*skip_addr = start_instr + cur_patch->skip_instr;
cur_patch += cur_patch->skip_patch;
} else {
/* Accepted this patch. Advance to the next
* one and wait for our intruction pointer to
* hit this point.
*/
cur_patch++;
}
}
*start_patch = cur_patch;
if (start_instr < *skip_addr)
/* Still skipping */
return (0);
return (1);
}
static u_int
ahd_resolve_seqaddr(struct ahd_softc *ahd, u_int address)
{
struct patch *cur_patch;
int address_offset;
u_int skip_addr;
u_int i;
address_offset = 0;
cur_patch = patches;
skip_addr = 0;
for (i = 0; i < address;) {
ahd_check_patch(ahd, &cur_patch, i, &skip_addr);
if (skip_addr > i) {
int end_addr;
end_addr = MIN(address, skip_addr);
address_offset += end_addr - i;
i = skip_addr;
} else {
i++;
}
}
return (address - address_offset);
}
static void
ahd_download_instr(struct ahd_softc *ahd, u_int instrptr, uint8_t *dconsts)
{
union ins_formats instr;
struct ins_format1 *fmt1_ins;
struct ins_format3 *fmt3_ins;
u_int opcode;
/*
* The firmware is always compiled into a little endian format.
*/
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
instr.integer = aic_le32toh(*(uint32_t*)&seqprog[instrptr * 4]);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
fmt1_ins = &instr.format1;
fmt3_ins = NULL;
/* Pull the opcode */
opcode = instr.format1.opcode;
switch (opcode) {
case AIC_OP_JMP:
case AIC_OP_JC:
case AIC_OP_JNC:
case AIC_OP_CALL:
case AIC_OP_JNE:
case AIC_OP_JNZ:
case AIC_OP_JE:
case AIC_OP_JZ:
{
fmt3_ins = &instr.format3;
fmt3_ins->address = ahd_resolve_seqaddr(ahd, fmt3_ins->address);
/* FALLTHROUGH */
}
case AIC_OP_OR:
case AIC_OP_AND:
case AIC_OP_XOR:
case AIC_OP_ADD:
case AIC_OP_ADC:
case AIC_OP_BMOV:
if (fmt1_ins->parity != 0) {
fmt1_ins->immediate = dconsts[fmt1_ins->immediate];
}
fmt1_ins->parity = 0;
/* FALLTHROUGH */
case AIC_OP_ROL:
{
int i, count;
/* Calculate odd parity for the instruction */
for (i = 0, count = 0; i < 31; i++) {
uint32_t mask;
mask = 0x01 << i;
if ((instr.integer & mask) != 0)
count++;
}
if ((count & 0x01) == 0)
instr.format1.parity = 1;
/* The sequencer is a little endian cpu */
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
instr.integer = aic_htole32(instr.integer);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_outsb(ahd, SEQRAM, instr.bytes, 4);
break;
}
default:
panic("Unknown opcode encountered in seq program");
break;
}
}
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
static int
ahd_probe_stack_size(struct ahd_softc *ahd)
{
int last_probe;
last_probe = 0;
while (1) {
int i;
/*
* We avoid using 0 as a pattern to avoid
* confusion if the stack implementation
* "back-fills" with zeros when "poping'
* entries.
*/
for (i = 1; i <= last_probe+1; i++) {
ahd_outb(ahd, STACK, i & 0xFF);
ahd_outb(ahd, STACK, (i >> 8) & 0xFF);
}
/* Verify */
for (i = last_probe+1; i > 0; i--) {
u_int stack_entry;
stack_entry = ahd_inb(ahd, STACK)
|(ahd_inb(ahd, STACK) << 8);
if (stack_entry != i)
goto sized;
}
last_probe++;
}
sized:
return (last_probe);
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
void
aic79xx.c: aic79xx_osm.h: aic7xxx_osm.h: Explicitly define functions that take no arguments with "(void)" Approved by: RE
2003-05-26 21:43:29 +00:00
ahd_dump_all_cards_state(void)
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
{
struct ahd_softc *list_ahd;
TAILQ_FOREACH(list_ahd, &ahd_tailq, links) {
ahd_dump_card_state(list_ahd);
}
}
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
int
ahd_print_register(ahd_reg_parse_entry_t *table, u_int num_entries,
const char *name, u_int address, u_int value,
u_int *cur_column, u_int wrap_point)
{
int printed;
u_int printed_mask;
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
if (cur_column != NULL && *cur_column >= wrap_point) {
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
printf("\n");
*cur_column = 0;
}
printed = printf("%s[0x%x]", name, value);
if (table == NULL) {
printed += printf(" ");
*cur_column += printed;
return (printed);
}
printed_mask = 0;
while (printed_mask != 0xFF) {
int entry;
for (entry = 0; entry < num_entries; entry++) {
if (((value & table[entry].mask)
!= table[entry].value)
|| ((printed_mask & table[entry].mask)
== table[entry].mask))
continue;
printed += printf("%s%s",
printed_mask == 0 ? ":(" : "|",
table[entry].name);
printed_mask |= table[entry].mask;
break;
}
if (entry >= num_entries)
break;
}
if (printed_mask != 0)
printed += printf(") ");
else
printed += printf(" ");
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
if (cur_column != NULL)
*cur_column += printed;
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
return (printed);
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
void
ahd_dump_card_state(struct ahd_softc *ahd)
{
struct scb *scb;
ahd_mode_state saved_modes;
u_int dffstat;
int paused;
u_int scb_index;
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
u_int saved_scb_index;
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
u_int cur_col;
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
int i;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if (ahd_is_paused(ahd)) {
paused = 1;
} else {
paused = 0;
ahd_pause(ahd);
}
saved_modes = ahd_save_modes(ahd);
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
printf(">>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<\n"
"%s: Dumping Card State at program address 0x%x Mode 0x%x\n",
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_name(ahd),
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
ahd_inw(ahd, CURADDR),
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_build_mode_state(ahd, ahd->saved_src_mode,
ahd->saved_dst_mode));
if (paused)
printf("Card was paused\n");
aic79xx.h: Add softc flag to indicate that we have seen at least one selection since the last bus reset or SE/LVD bus change. aic79xx.c: Fix a few style nits. In ahd_update_pending_scbs(), only touch card registers once we have found an SCB that needs to be updated. This removes lots of clutter from PCI traces taken of error recovery performed by the driver. Short circuit the first selection iocell workaround handler if we've run once since the last bus reset or iocell change. This also removes clutter from PCI traces. Note if completions are pending in the qoutfifo when we dump card state.
2003-06-28 04:45:25 +00:00
if (ahd_check_cmdcmpltqueues(ahd))
printf("Completions are pending\n");
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
/*
* Mode independent registers.
*/
cur_col = 0;
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
ahd_hs_mailbox_print(ahd_inb(ahd, LOCAL_HS_MAILBOX), &cur_col, 50);
ahd_intctl_print(ahd_inb(ahd, INTCTL), &cur_col, 50);
ahd_seqintstat_print(ahd_inb(ahd, SEQINTSTAT), &cur_col, 50);
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
ahd_saved_mode_print(ahd_inb(ahd, SAVED_MODE), &cur_col, 50);
ahd_dffstat_print(ahd_inb(ahd, DFFSTAT), &cur_col, 50);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
ahd_scsisigi_print(ahd_inb(ahd, SCSISIGI), &cur_col, 50);
ahd_scsiphase_print(ahd_inb(ahd, SCSIPHASE), &cur_col, 50);
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
ahd_scsibus_print(ahd_inb(ahd, SCSIBUS), &cur_col, 50);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
ahd_lastphase_print(ahd_inb(ahd, LASTPHASE), &cur_col, 50);
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
ahd_scsiseq0_print(ahd_inb(ahd, SCSISEQ0), &cur_col, 50);
ahd_scsiseq1_print(ahd_inb(ahd, SCSISEQ1), &cur_col, 50);
ahd_seqctl0_print(ahd_inb(ahd, SEQCTL0), &cur_col, 50);
ahd_seqintctl_print(ahd_inb(ahd, SEQINTCTL), &cur_col, 50);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
ahd_seq_flags_print(ahd_inb(ahd, SEQ_FLAGS), &cur_col, 50);
ahd_seq_flags2_print(ahd_inb(ahd, SEQ_FLAGS2), &cur_col, 50);
ahd_sstat0_print(ahd_inb(ahd, SSTAT0), &cur_col, 50);
ahd_sstat1_print(ahd_inb(ahd, SSTAT1), &cur_col, 50);
ahd_sstat2_print(ahd_inb(ahd, SSTAT2), &cur_col, 50);
ahd_sstat3_print(ahd_inb(ahd, SSTAT3), &cur_col, 50);
ahd_perrdiag_print(ahd_inb(ahd, PERRDIAG), &cur_col, 50);
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
ahd_simode1_print(ahd_inb(ahd, SIMODE1), &cur_col, 50);
ahd_lqistat0_print(ahd_inb(ahd, LQISTAT0), &cur_col, 50);
ahd_lqistat1_print(ahd_inb(ahd, LQISTAT1), &cur_col, 50);
ahd_lqistat2_print(ahd_inb(ahd, LQISTAT2), &cur_col, 50);
ahd_lqostat0_print(ahd_inb(ahd, LQOSTAT0), &cur_col, 50);
ahd_lqostat1_print(ahd_inb(ahd, LQOSTAT1), &cur_col, 50);
ahd_lqostat2_print(ahd_inb(ahd, LQOSTAT2), &cur_col, 50);
printf("\n");
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
printf("\nSCB Count = %d CMDS_PENDING = %d LASTSCB 0x%x "
"CURRSCB 0x%x NEXTSCB 0x%x\n",
ahd->scb_data.numscbs, ahd_inw(ahd, CMDS_PENDING),
ahd_inw(ahd, LASTSCB), ahd_inw(ahd, CURRSCB),
ahd_inw(ahd, NEXTSCB));
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
cur_col = 0;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/* QINFIFO */
ahd_search_qinfifo(ahd, CAM_TARGET_WILDCARD, ALL_CHANNELS,
CAM_LUN_WILDCARD, SCB_LIST_NULL,
ROLE_UNKNOWN, /*status*/0, SEARCH_PRINT);
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
saved_scb_index = ahd_get_scbptr(ahd);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
printf("Pending list:");
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
i = 0;
LIST_FOREACH(scb, &ahd->pending_scbs, pending_links) {
if (i++ > AHD_SCB_MAX)
break;
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
cur_col = printf("\n%3d FIFO_USE[0x%x] ", SCB_GET_TAG(scb),
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
ahd_inb_scbram(ahd, SCB_FIFO_USE_COUNT));
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_set_scbptr(ahd, SCB_GET_TAG(scb));
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
ahd_scb_control_print(ahd_inb_scbram(ahd, SCB_CONTROL),
&cur_col, 60);
ahd_scb_scsiid_print(ahd_inb_scbram(ahd, SCB_SCSIID),
&cur_col, 60);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
printf("\nTotal %d\n", i);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
printf("Kernel Free SCB list: ");
i = 0;
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
TAILQ_FOREACH(scb, &ahd->scb_data.free_scbs, links.tqe) {
struct scb *list_scb;
list_scb = scb;
do {
printf("%d ", SCB_GET_TAG(list_scb));
list_scb = LIST_NEXT(list_scb, collision_links);
} while (list_scb && i++ < AHD_SCB_MAX);
}
LIST_FOREACH(scb, &ahd->scb_data.any_dev_free_scb_list, links.le) {
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if (i++ > AHD_SCB_MAX)
break;
printf("%d ", SCB_GET_TAG(scb));
}
printf("\n");
printf("Sequencer Complete DMA-inprog list: ");
scb_index = ahd_inw(ahd, COMPLETE_SCB_DMAINPROG_HEAD);
i = 0;
while (!SCBID_IS_NULL(scb_index) && i++ < AHD_SCB_MAX) {
ahd_set_scbptr(ahd, scb_index);
printf("%d ", scb_index);
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
scb_index = ahd_inw_scbram(ahd, SCB_NEXT_COMPLETE);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
printf("\n");
printf("Sequencer Complete list: ");
scb_index = ahd_inw(ahd, COMPLETE_SCB_HEAD);
i = 0;
while (!SCBID_IS_NULL(scb_index) && i++ < AHD_SCB_MAX) {
ahd_set_scbptr(ahd, scb_index);
printf("%d ", scb_index);
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
scb_index = ahd_inw_scbram(ahd, SCB_NEXT_COMPLETE);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
printf("\n");
printf("Sequencer DMA-Up and Complete list: ");
scb_index = ahd_inw(ahd, COMPLETE_DMA_SCB_HEAD);
i = 0;
while (!SCBID_IS_NULL(scb_index) && i++ < AHD_SCB_MAX) {
ahd_set_scbptr(ahd, scb_index);
printf("%d ", scb_index);
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
scb_index = ahd_inw_scbram(ahd, SCB_NEXT_COMPLETE);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
printf("\n");
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
ahd_set_scbptr(ahd, saved_scb_index);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
dffstat = ahd_inb(ahd, DFFSTAT);
for (i = 0; i < 2; i++) {
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
#ifdef AHD_DEBUG
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
struct scb *fifo_scb;
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
#endif
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
u_int fifo_scbptr;
ahd_set_modes(ahd, AHD_MODE_DFF0 + i, AHD_MODE_DFF0 + i);
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
fifo_scbptr = ahd_get_scbptr(ahd);
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
printf("\n%s: FIFO%d %s, LONGJMP == 0x%x, SCB 0x%x\n",
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_name(ahd), i,
(dffstat & (FIFO0FREE << i)) ? "Free" : "Active",
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
ahd_inw(ahd, LONGJMP_ADDR), fifo_scbptr);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
cur_col = 0;
ahd_seqimode_print(ahd_inb(ahd, SEQIMODE), &cur_col, 50);
ahd_seqintsrc_print(ahd_inb(ahd, SEQINTSRC), &cur_col, 50);
ahd_dfcntrl_print(ahd_inb(ahd, DFCNTRL), &cur_col, 50);
ahd_dfstatus_print(ahd_inb(ahd, DFSTATUS), &cur_col, 50);
ahd_sg_cache_shadow_print(ahd_inb(ahd, SG_CACHE_SHADOW),
&cur_col, 50);
ahd_sg_state_print(ahd_inb(ahd, SG_STATE), &cur_col, 50);
ahd_dffsxfrctl_print(ahd_inb(ahd, DFFSXFRCTL), &cur_col, 50);
ahd_soffcnt_print(ahd_inb(ahd, SOFFCNT), &cur_col, 50);
ahd_mdffstat_print(ahd_inb(ahd, MDFFSTAT), &cur_col, 50);
if (cur_col > 50) {
printf("\n");
cur_col = 0;
}
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
cur_col += printf("SHADDR = 0x%x%x, SHCNT = 0x%x ",
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
ahd_inl(ahd, SHADDR+4),
ahd_inl(ahd, SHADDR),
(ahd_inb(ahd, SHCNT)
| (ahd_inb(ahd, SHCNT + 1) << 8)
| (ahd_inb(ahd, SHCNT + 2) << 16)));
if (cur_col > 50) {
printf("\n");
cur_col = 0;
}
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
cur_col += printf("HADDR = 0x%x%x, HCNT = 0x%x ",
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
ahd_inl(ahd, HADDR+4),
ahd_inl(ahd, HADDR),
(ahd_inb(ahd, HCNT)
| (ahd_inb(ahd, HCNT + 1) << 8)
| (ahd_inb(ahd, HCNT + 2) << 16)));
ahd_ccsgctl_print(ahd_inb(ahd, CCSGCTL), &cur_col, 50);
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_SG) != 0) {
fifo_scb = ahd_lookup_scb(ahd, fifo_scbptr);
if (fifo_scb != NULL)
ahd_dump_sglist(fifo_scb);
}
#endif
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
printf("\nLQIN: ");
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
for (i = 0; i < 20; i++)
printf("0x%x ", ahd_inb(ahd, LQIN + i));
printf("\n");
ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG);
printf("%s: LQISTATE = 0x%x, LQOSTATE = 0x%x, OPTIONMODE = 0x%x\n",
ahd_name(ahd), ahd_inb(ahd, LQISTATE), ahd_inb(ahd, LQOSTATE),
ahd_inb(ahd, OPTIONMODE));
printf("%s: OS_SPACE_CNT = 0x%x MAXCMDCNT = 0x%x\n",
ahd_name(ahd), ahd_inb(ahd, OS_SPACE_CNT),
ahd_inb(ahd, MAXCMDCNT));
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
ahd_simode0_print(ahd_inb(ahd, SIMODE0), &cur_col, 50);
printf("\n");
aic79xx.c: Implement the SCB_SILENT flag. This is useful for hushing up the driver during DV or other operations that we expect to cause transmission errors. The messages will still print if the SHOW_MASKED_ERRORS debug option is enabled. Save and restore the NEGOADDR address when setting new transfer settings. The sequencer performs lookups in the negotiation table too and it expects NEGOADDR to remain consistent across pause/unpause sessions. Consistently use "offset" instead of "period" to determine if we are running sync or not. Add a SHOW_MESSAGES diagnostic for when we assert ATN during message processing. Print out IU, QAS, and RTI features when showing transfer options. Limit the syncrate after all option conformance changes have taken place in ahd_devlimited_syncrate. Changes in options may change the final syncrate we accept. Keep a copy of the hs_mailbox in our softc so that we can perform read/modify/write operations on the hs_mailbox without having to pause the sequencer to read the last written value. Use the ENINT_COALESS flag in the hs_mailbox to toggle interrupt coalessing. Add entrypoints for enabling interrupt coalessing and setting both a timeout (how long to wait for commands to be coalessed) and a maximum commands to coaless value. Add a statistics timer that decides when to enable or disable interrupt coalessing based on load. Add a routine, ahd_reset_cmds_pending() which is used to update the CMDS_PENDING sequencer variable whenever error recovery compeltes SCBs without notifying the sequencer. Since ahd_reset_cmds_pending is called during ahd_unpause() only if we've aborted SCBs, its call to ahd_flush_qoutfifo should not cause recursion through ahd_run_qoutfifo(). A panic has been added to ensure that this recursion does not occur. In ahd_search_qinfifo, update the CMDS_PENDING sequencer variable directly. ahd_search_qinififo can be called in situations where using ahd_reset_cmds_pending() might cause recursion. Since we can safely determine the exact number to reduce CMDS_PENDING by in this scenario without running the qoutfifo, the manual update is sufficient. Clean up diagnostics. Add ahd_flush_qoutfifo() which will run the qoutfifo as well as complete any commands sitting on the sequencer's COMPLETE_SCB lists or the good status FIFO. Use this routine in several places that did similar things in an add-hoc, but incomplete, fashion. A call to this routine was also added to ahd_abort_scbs() to close a race. In ahd_pause_and_flushwork() only return once selections are safely disabled. Flush all completed commands via ahd_flush_qoutfifo(). Remove "Now packetized" diagnostic now that this information is incorperated into the actual negotiation messages that are displayed. When forcing renegotiation, don't clober the current ppr_options. Much of the driver uses this information to determine if we are currently packetized or not. Remove some stray spaces at column 1 in ahd_set_tags. When complaining about getting a host message loop request with no pending messages, print out the SCB_CONTROL register down on the card. Modify the ahd_sent_msg() routine to handle a search for an outgoing identify message. Use this to detect a msg reject on an identify message which typically indicates that the target thought we were packetized. Force a renegotiation in this case. In ahd_search_qinfifo(), wait more effectively for SCB DMA activities to cease. We also disable SCB fetch operations since we are about to change the qinfifo and any fetch in progress will likely be invalidated. In ahd_qinfifo_count(), fix the qinfifo empty case. In ahd_dump_card_state(), print out CCSCBCTL in the correct mode. If we are a narrow controller, don't set the current width to unknown when forcing a future negotiation. This just confuses the code into attempting a wide negotiation on a narrow bus. Add support for task management function completions. Modify ahd_handle_devreset so that it can handle lun resets in addition to target resets. Use ahd_handle_devreset for lun and target reset task management functions. Handle the abort task TMF race case better. We now wait until any current selections are over and then set the TMF back to zero. This should cause the sequencer to ignore the abort TMF completion should it occur. Correct a bug in the illegal phase handler that caused us to drop down to narrow when handling the unexpected command phase case after 3rd party reset of a packetized device. Indicate the features, bugs, and flags set in the softc that are used to control firmware patch download when booting verbose. aic79xx.h: Add coalessing and HS_MAILBOX fields. Add per-softc variables for the stats "daemon". Add a debug option for interrupt coalessing activities. Add two new softc flags: o AHD_UPDATE_PEND_CMDS Run ahd_reset_cmds_pending() on the next unpause. o AHD_RUNNING_QOUTFIFO Used to catch recursion through ahd_run_qoutfifo(). aic79xx.reg: Correct register addresses related to the software timer and the DFDBCTL register. Add constants paramaterizing the software timer. Add scratch ram locations for storing interrupt coalessing tunables. Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2. In at least the REV A, these are writable bits. We make use of that for a swtimer workaround in the sequencer. Since HS_MAILBOX autoclears, provide a sequencer variable to store its contents. Add SEQINT codes for handling task management completions. aic79xx.seq: Correct ignore wide residue processing check for a wide negotiation being in effect. We must be in the SCSI register window in order to access the negotiation table. Use the software timer and a commands completed count to implement interrupt coalessing. The command complete is deferred until either the maximum command threshold or a the expiration of a command deferral timer. If we have more SCBs to complete to the host (sitting in COMPLETE_SCB lists), always try to coaless them up to our coalessing limit. If coalessing is enabled, but we have fewer commands oustanting than the host's min coalessing limit, complete the command immediately. Add code to track the number of commands outstanding. Commands are outstanding from the time they are placed into the execution queue until the DMA to post completion is setup. Add a workaround for intvec_2 interrupts on the H2A4. In H2A4, the mode pointer is not saved for intvec2, but is restored on iret. This can lead to the restoration of a bogus mode ptr. Manually clear the intmask bits and do a normal return to compensate. We use intvec_2 to track interrupt coalessing timeouts. Since we cannot disable the swtimer's countdown, simply mask its interrupt once we no longer care about it firing. In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime we are notified of an HS_MAILBOX update via the HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a local copy of persistant portions of the HS_MAILBOX as the mailbox auto-clears on any read. Move the test for the cfg4istat interrupt up an instruction to hopefully close a race between the next outgoing selection and our disabling of selections. Add a missing ret to the last instruction in load_overrun_buf. Add notifications to the host of task management completions as well as the completions for commands that completed successfully before their corresponding TMF could be sent. Hold a critical section during select-out processing until we have a fully identified connection. This removes a race condition with the legacy abort handler. Correct a few spelling errors in some comments. aic79xx_inline.h: Call ahd_reset_cmds_pending() in ahd_unpause if required. Update cmdcmplt interrupt statistics in our interrupt handler. Allow callers to ahd_send_scb() to set the task management function. aic79xx_pci.c: Disable SERR and pause the controller prior to performing our mmapped I/O test. The U320 controllers do not support "auto-access-pause". aic79xx_osm.c: Set the task management function now that ahd_send_scb() doesn't do it for us. We also perform a lun reset in response to BDR requests to packetized devices.
2003-01-20 20:17:35 +00:00
ahd_set_modes(ahd, AHD_MODE_CCHAN, AHD_MODE_CCHAN);
cur_col = 0;
ahd_ccscbctl_print(ahd_inb(ahd, CCSCBCTL), &cur_col, 50);
printf("\n");
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_set_modes(ahd, ahd->saved_src_mode, ahd->saved_dst_mode);
printf("%s: REG0 == 0x%x, SINDEX = 0x%x, DINDEX = 0x%x\n",
ahd_name(ahd), ahd_inw(ahd, REG0), ahd_inw(ahd, SINDEX),
ahd_inw(ahd, DINDEX));
printf("%s: SCBPTR == 0x%x, SCB_NEXT == 0x%x, SCB_NEXT2 == 0x%x\n",
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
ahd_name(ahd), ahd_get_scbptr(ahd),
ahd_inw_scbram(ahd, SCB_NEXT),
ahd_inw_scbram(ahd, SCB_NEXT2));
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
printf("CDB %x %x %x %x %x %x\n",
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
ahd_inb_scbram(ahd, SCB_CDB_STORE),
ahd_inb_scbram(ahd, SCB_CDB_STORE+1),
ahd_inb_scbram(ahd, SCB_CDB_STORE+2),
ahd_inb_scbram(ahd, SCB_CDB_STORE+3),
ahd_inb_scbram(ahd, SCB_CDB_STORE+4),
ahd_inb_scbram(ahd, SCB_CDB_STORE+5));
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
printf("STACK:");
Major update to the ahd driver to fix many bugs found in the previous version, plus add support for the new features found in the Rev B version of the chip. The changelog is quite long and can be provided on request. Major features include vastly improved protocol violation handling, full support for the 7902 Rev B, better parity error handling, and better packetized overrun handling, to name a few. Approved by: re (blanket)
2002-12-01 08:13:37 +00:00
for (i = 0; i < ahd->stack_size; i++) {
ahd->saved_stack[i] =
ahd_inb(ahd, STACK)|(ahd_inb(ahd, STACK) << 8);
printf(" 0x%x", ahd->saved_stack[i]);
}
for (i = ahd->stack_size-1; i >= 0; i--) {
ahd_outb(ahd, STACK, ahd->saved_stack[i] & 0xFF);
ahd_outb(ahd, STACK, (ahd->saved_stack[i] >> 8) & 0xFF);
}
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
printf("\n<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>\n");
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_platform_dump_card_state(ahd);
ahd_restore_modes(ahd, saved_modes);
if (paused == 0)
ahd_unpause(ahd);
}
void
ahd_dump_scbs(struct ahd_softc *ahd)
{
ahd_mode_state saved_modes;
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
u_int saved_scb_index;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
int i;
saved_modes = ahd_save_modes(ahd);
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
saved_scb_index = ahd_get_scbptr(ahd);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
for (i = 0; i < AHD_SCB_MAX; i++) {
ahd_set_scbptr(ahd, i);
printf("%3d", i);
printf("(CTRL 0x%x ID 0x%x N 0x%x N2 0x%x SG 0x%x, RSG 0x%x)\n",
Fix a race condition in the flushing of commands that have completed across the bus but not to the host before processing of an exception condition (busfree, bus reset, etc.). When flushing the controller of completed commands, we also look for packetized commands that have completed with good status and are stored in the "good status fifo". The hardware will post to the good status fifo even if data for that command is still active in a FIFO. In one particular failure case, a command outstanding on the bus reconnected, transferred data into a FIFO, and provided good status while the host driver was processing an expected busfree event (PPR message negotiation). This resulted in an entry in the good status fifo that we completed, but since the sequencer was paused, the data in the data FIFO for this command had never been transferred to the host. Once the busfree processing was complete, the sequencer was unpaused, and the data completed its transfer to the host. In some instances, the client for the data was notified of the completion and attempted to view the data before it arrived. This case only occurred during FreeBSD's multi-target probe of the SCSI bus while some devices are negotiating to go packetized and some devices are already running in packetized. The fix is to run and FIFOs active with a context in the good status fifo to completion before completing the command to the SCSI layer. This requies duplicating the FIFO rundown operations in the host driver that would usually be handled by the firmware, but there is no other alternative. Don't blindly shutdown the SCB dma engine when restarting the sequencer. We may be killing an operation that is not supposed to be cancelled. The cases where we need to shutdown these dma engines are already handled elsewhere in the driver. Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
2003-06-28 04:46:54 +00:00
ahd_inb_scbram(ahd, SCB_CONTROL),
ahd_inb_scbram(ahd, SCB_SCSIID),
ahd_inw_scbram(ahd, SCB_NEXT),
ahd_inw_scbram(ahd, SCB_NEXT2),
ahd_inl_scbram(ahd, SCB_SGPTR),
ahd_inl_scbram(ahd, SCB_RESIDUAL_SGPTR));
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
printf("\n");
Upgrade to version 1.1 of the aic79xx U320 driver. aic79xx.c: o Remove redundant ahd_update_modes() call. o Correct panic in diagnostic should state corruption cause the SCB Id to be invalid during a selection timeout. o Add workaround for missing BUSFREEREV feature in Rev A silicon. o Corect formatting nits. o Use register pretty printing in more places. o Save and restore our SCB pointer when updating the waiting queue list for an "expected" LQ-out busfree. o In ahd_clear_intstat, deal with the missing autoclear in the CLRLQO* registers. o BE fixup in a diagnostic printf. o Make sure that we are in the proper mode before disabling selections in ahd_update_pending_scbs. o Add more diagnostics. o task_attribute_nonpkt_tag -> task_attribute: we don't need a nonpkt_tag field anymore for allowing all 512 SCBs to be used in non-packetized connections. o Negotiate HOLD_MCS to U320 devices. o Add a few additional mode assertions. o Restore the chip mode after clearing out the qinfifo so that code using ahd_abort_scbs sees a consistent mode. o Simplify the DMA engine shutdown routine prior to performing a bus reset. o Perform the sequencer restart after a chip reset prior to setting up our timer to poll for the reset to be complete. On some OSes, the timer could actually pre-empt us and order is important here. o Have our "reset poller" set the expected mode since there is no guarantee of what mode will be in force when we are called from the OS timer. o Save and restore the SCB pointer in ahd_dump_card_state(). This routine must not modify card state. o Ditto for ahd_dump_scbs(). aic79xx.h: o Add a few more chip bug definitions. o Align our tag on a 32bit boundary. aic79xx.reg: aic79xx.seq: o Start work on removing workarounds for Rev B. o Use a special location in scratch from for stroring our SCBPTR during legacy FIFO allocations. This corrects problems in mixed packetized/non-packetized configurations where calling into a FIFO task corrupted our SCBPTR. o Don't rely on DMA priority to guarantee that all data in our FIFOs will flush prior to a command completion notification going out of the command channel. We've never seen this assumption fail, but better safe than sorry. o Deal with missing BUSFREEREV feature in H2A. o Simplify disconnect list code now that the list will always have only a single entry. o Implement the AHD_REG_SLOW_SETTLE_BUG workaround. o Swith to using "REG_ISR" for local mode scratch during our ISR. o Add a missing jmp to the data_group_dma_loop after our data pointers have been re-initialized by the kernel. o Correct test in the bitbucket code so that we actually wait for the bitbucket to complete before signaling the kernel of the overrun condition. o Reposition pkt_saveptrs to avoid a jmp instruction. o Update a comment to reflect that the code now waits for a FIFO to drain prior to issuing a CLRCHN. aic79xx_inline.h: o Remove unused untagged queue handling code. o Don't attempt to htole64 what could be a 32bit value. aic79xx_pci.c: o Set additional bug flags for rev A chips.
2002-09-26 22:54:00 +00:00
ahd_set_scbptr(ahd, saved_scb_index);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_restore_modes(ahd, saved_modes);
}
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
/*************************** Timeout Handling *********************************/
void
ahd_timeout(struct scb *scb)
{
struct ahd_softc *ahd;
ahd = scb->ahd_softc;
if ((scb->flags & SCB_ACTIVE) != 0) {
if ((scb->flags & SCB_TIMEDOUT) == 0) {
LIST_INSERT_HEAD(&ahd->timedout_scbs, scb,
timedout_links);
scb->flags |= SCB_TIMEDOUT;
}
ahd_wakeup_recovery_thread(ahd);
}
}
/*
* ahd_recover_commands determines if any of the commands that have currently
* timedout are the root cause for this timeout. Innocent commands are given
* a new timeout while we wait for the command executing on the bus to timeout.
* This routine is invoked from a thread context so we are allowed to sleep.
* Our lock is not held on entry.
*/
void
ahd_recover_commands(struct ahd_softc *ahd)
{
struct scb *scb;
struct scb *active_scb;
long s;
int found;
int was_paused;
u_int active_scbptr;
u_int last_phase;
ahd_lock(ahd, &s);
/*
* Pause the controller and manually flush any
* commands that have just completed but that our
* interrupt handler has yet to see.
*/
was_paused = ahd_is_paused(ahd);
ahd_pause_and_flushwork(ahd);
if (LIST_EMPTY(&ahd->timedout_scbs) != 0) {
/*
* The timedout commands have already
* completed. This typically means
* that either the timeout value was on
* the hairy edge of what the device
* requires or - more likely - interrupts
* are not happening.
*/
printf("%s: Timedout SCBs already complete. "
"Interrupts may not be functioning.\n", ahd_name(ahd));
ahd_unpause(ahd);
ahd_unlock(ahd, &s);
return;
}
printf("%s: Recovery Initiated - Card was %spaused\n", ahd_name(ahd),
was_paused ? "" : "not ");
ahd_dump_card_state(ahd);
/*
* Determine identity of SCB acting on the bus.
* This test only catches non-packetized transactions.
* Due to the fleeting nature of packetized operations,
* we can't easily determine that a packetized operation
* is on the bus.
*/
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
last_phase = ahd_inb(ahd, LASTPHASE);
active_scbptr = ahd_get_scbptr(ahd);
active_scb = NULL;
if (last_phase != P_BUSFREE
|| (ahd_inb(ahd, SEQ_FLAGS) & NOT_IDENTIFIED) == 0)
active_scb = ahd_lookup_scb(ahd, active_scbptr);
while ((scb = LIST_FIRST(&ahd->timedout_scbs)) != NULL) {
int target;
int lun;
char channel;
target = SCB_GET_TARGET(ahd, scb);
channel = SCB_GET_CHANNEL(ahd, scb);
lun = SCB_GET_LUN(scb);
ahd_print_path(ahd, scb);
printf("SCB 0x%x - timed out\n", scb->hscb->tag);
if (scb->flags & (SCB_DEVICE_RESET|SCB_ABORT)) {
/*
* Been down this road before.
* Do a full bus reset.
*/
aic_set_transaction_status(scb, CAM_CMD_TIMEOUT);
bus_reset:
found = ahd_reset_channel(ahd, channel,
/*Initiate Reset*/TRUE);
printf("%s: Issued Channel %c Bus Reset. "
"%d SCBs aborted\n", ahd_name(ahd), channel,
found);
continue;
}
/*
* Remove the command from the timedout list in
* preparation for requeing it.
*/
LIST_REMOVE(scb, timedout_links);
scb->flags &= ~SCB_TIMEDOUT;
if (active_scb != NULL) {
if (active_scb != scb) {
/*
* If the active SCB is not us, assume that
* the active SCB has a longer timeout than
* the timedout SCB, and wait for the active
* SCB to timeout.
*/
ahd_other_scb_timeout(ahd, scb, active_scb);
continue;
}
/*
* We're active on the bus, so assert ATN
* and hope that the target responds.
*/
ahd_set_recoveryscb(ahd, active_scb);
active_scb->flags |= SCB_RECOVERY_SCB|SCB_DEVICE_RESET;
ahd_outb(ahd, MSG_OUT, HOST_MSG);
ahd_outb(ahd, SCSISIGO, last_phase|ATNO);
ahd_print_path(ahd, active_scb);
printf("BDR message in message buffer\n");
aic_scb_timer_reset(scb, 2 * 1000000);
break;
} else if (last_phase != P_BUSFREE
&& ahd_inb(ahd, SCSIPHASE) == 0) {
/*
* SCB is not identified, there
* is no pending REQ, and the sequencer
* has not seen a busfree. Looks like
* a stuck connection waiting to
* go busfree. Reset the bus.
*/
printf("%s: Connection stuck awaiting busfree or "
"Identify Msg.\n", ahd_name(ahd));
goto bus_reset;
} else if (ahd_search_qinfifo(ahd, target, channel, lun,
scb->hscb->tag, ROLE_INITIATOR,
/*status*/0, SEARCH_COUNT) > 0) {
/*
* We haven't even gone out on the bus
* yet, so the timeout must be due to
* some other command. Reset the timer
* and go on.
*/
ahd_other_scb_timeout(ahd, scb, scb);
} else {
/*
* This SCB is for a disconnected transaction
* and we haven't found a better candidate on
* the bus to explain this timeout.
*/
ahd_set_recoveryscb(ahd, scb);
/*
* Actually re-queue this SCB in an attempt
* to select the device before it reconnects.
* In either case (selection or reselection),
* we will now issue a target reset to the
* timed-out device.
*
* Set the MK_MESSAGE control bit indicating
* that we desire to send a message. We
* also set the disconnected flag since
* in the paging case there is no guarantee
* that our SCB control byte matches the
* version on the card. We don't want the
* sequencer to abort the command thinking
* an unsolicited reselection occurred.
*/
scb->flags |= SCB_DEVICE_RESET;
scb->hscb->cdb_len = 0;
scb->hscb->task_attribute = 0;
scb->hscb->task_management = SIU_TASKMGMT_ABORT_TASK;
ahd_set_scbptr(ahd, SCB_GET_TAG(scb));
if ((scb->flags & SCB_PACKETIZED) != 0) {
/*
* Mark the SCB has having an outstanding
* task management function. Should the command
* complete normally before the task management
* function can be sent, the host will be
* notified to abort our requeued SCB.
*/
ahd_outb(ahd, SCB_TASK_MANAGEMENT,
scb->hscb->task_management);
} else {
/*
* If non-packetized, set the MK_MESSAGE control
* bit indicating that we desire to send a
* message. We also set the disconnected flag
* since there is no guarantee that our SCB
* control byte matches the version on the
* card. We don't want the sequencer to abort
* the command thinking an unsolicited
* reselection occurred.
*/
scb->hscb->control |= MK_MESSAGE|DISCONNECTED;
/*
* The sequencer will never re-reference the
* in-core SCB. To make sure we are notified
* during reslection, set the MK_MESSAGE flag in
* the card's copy of the SCB.
*/
ahd_outb(ahd, SCB_CONTROL,
ahd_inb(ahd, SCB_CONTROL)|MK_MESSAGE);
}
/*
* Clear out any entries in the QINFIFO first
* so we are the next SCB for this target
* to run.
*/
ahd_search_qinfifo(ahd, target, channel, lun,
SCB_LIST_NULL, ROLE_INITIATOR,
CAM_REQUEUE_REQ, SEARCH_COMPLETE);
ahd_qinfifo_requeue_tail(ahd, scb);
ahd_set_scbptr(ahd, active_scbptr);
ahd_print_path(ahd, scb);
printf("Queuing a BDR SCB\n");
aic_scb_timer_reset(scb, 2 * 1000000);
break;
}
}
/*
* Any remaining SCBs were not the "culprit", so remove
* them from the timeout list. The timer for these commands
* will be reset once the recovery SCB completes.
*/
while ((scb = LIST_FIRST(&ahd->timedout_scbs)) != NULL) {
LIST_REMOVE(scb, timedout_links);
scb->flags &= ~SCB_TIMEDOUT;
}
ahd_unpause(ahd);
ahd_unlock(ahd, &s);
}
static void
ahd_other_scb_timeout(struct ahd_softc *ahd, struct scb *scb,
struct scb *other_scb)
{
u_int newtimeout;
ahd_print_path(ahd, scb);
printf("Other SCB Timeout%s",
(scb->flags & SCB_OTHERTCL_TIMEOUT) != 0
? " again\n" : "\n");
scb->flags |= SCB_OTHERTCL_TIMEOUT;
newtimeout = MAX(aic_get_timeout(other_scb),
aic_get_timeout(scb));
aic_scb_timer_reset(scb, newtimeout);
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
/**************************** Flexport Logic **********************************/
/*
* Read count 16bit words from 16bit word address start_addr from the
* SEEPROM attached to the controller, into buf, using the controller's
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
* SEEPROM reading state machine. Optionally treat the data as a byte
* stream in terms of byte order.
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
*/
int
ahd_read_seeprom(struct ahd_softc *ahd, uint16_t *buf,
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
u_int start_addr, u_int count, int bytestream)
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
{
u_int cur_addr;
u_int end_addr;
int error;
/*
* If we never make it through the loop even once,
* we were passed invalid arguments.
*/
error = EINVAL;
AHD_ASSERT_MODES(ahd, AHD_MODE_SCSI_MSK, AHD_MODE_SCSI_MSK);
end_addr = start_addr + count;
for (cur_addr = start_addr; cur_addr < end_addr; cur_addr++) {
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_outb(ahd, SEEADR, cur_addr);
ahd_outb(ahd, SEECTL, SEEOP_READ | SEESTART);
error = ahd_wait_seeprom(ahd);
if (error)
break;
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
if (bytestream != 0) {
uint8_t *bytestream_ptr;
bytestream_ptr = (uint8_t *)buf;
*bytestream_ptr++ = ahd_inb(ahd, SEEDAT);
*bytestream_ptr = ahd_inb(ahd, SEEDAT+1);
} else {
/*
* ahd_inw() already handles machine byte order.
*/
*buf = ahd_inw(ahd, SEEDAT);
}
buf++;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
return (error);
}
/*
* Write count 16bit words from buf, into SEEPROM attache to the
* controller starting at 16bit word address start_addr, using the
* controller's SEEPROM writing state machine.
*/
int
ahd_write_seeprom(struct ahd_softc *ahd, uint16_t *buf,
u_int start_addr, u_int count)
{
u_int cur_addr;
u_int end_addr;
int error;
int retval;
AHD_ASSERT_MODES(ahd, AHD_MODE_SCSI_MSK, AHD_MODE_SCSI_MSK);
error = ENOENT;
/* Place the chip into write-enable mode */
ahd_outb(ahd, SEEADR, SEEOP_EWEN_ADDR);
ahd_outb(ahd, SEECTL, SEEOP_EWEN | SEESTART);
error = ahd_wait_seeprom(ahd);
if (error)
return (error);
/*
* Write the data. If we don't get throught the loop at
* least once, the arguments were invalid.
*/
retval = EINVAL;
end_addr = start_addr + count;
for (cur_addr = start_addr; cur_addr < end_addr; cur_addr++) {
ahd_outw(ahd, SEEDAT, *buf++);
ahd_outb(ahd, SEEADR, cur_addr);
ahd_outb(ahd, SEECTL, SEEOP_WRITE | SEESTART);
retval = ahd_wait_seeprom(ahd);
if (retval)
break;
}
/*
* Disable writes.
*/
ahd_outb(ahd, SEEADR, SEEOP_EWDS_ADDR);
ahd_outb(ahd, SEECTL, SEEOP_EWDS | SEESTART);
error = ahd_wait_seeprom(ahd);
if (error)
return (error);
return (retval);
}
/*
* Wait ~100us for the serial eeprom to satisfy our request.
*/
int
ahd_wait_seeprom(struct ahd_softc *ahd)
{
int cnt;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
cnt = 5000;
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
while ((ahd_inb(ahd, SEESTAT) & (SEEARBACK|SEEBUSY)) != 0 && --cnt)
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_delay(5);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if (cnt == 0)
return (ETIMEDOUT);
return (0);
}
Correct spelling errors. Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending.
2003-05-04 00:20:07 +00:00
/*
* Validate the two checksums in the per_channel
* vital product data struct.
*/
int
ahd_verify_vpd_cksum(struct vpd_config *vpd)
{
int i;
int maxaddr;
uint32_t checksum;
uint8_t *vpdarray;
vpdarray = (uint8_t *)vpd;
maxaddr = offsetof(struct vpd_config, vpd_checksum);
checksum = 0;
for (i = offsetof(struct vpd_config, resource_type); i < maxaddr; i++)
checksum = checksum + vpdarray[i];
if (checksum == 0
|| (-checksum & 0xFF) != vpd->vpd_checksum)
return (0);
checksum = 0;
maxaddr = offsetof(struct vpd_config, checksum);
for (i = offsetof(struct vpd_config, default_target_flags);
i < maxaddr; i++)
checksum = checksum + vpdarray[i];
if (checksum == 0
|| (-checksum & 0xFF) != vpd->checksum)
return (0);
return (1);
}
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
int
ahd_verify_cksum(struct seeprom_config *sc)
{
int i;
int maxaddr;
uint32_t checksum;
uint16_t *scarray;
maxaddr = (sizeof(*sc)/2) - 1;
checksum = 0;
scarray = (uint16_t *)sc;
for (i = 0; i < maxaddr; i++)
checksum = checksum + scarray[i];
if (checksum == 0
|| (checksum & 0xFFFF) != sc->checksum) {
return (0);
} else {
return (1);
}
}
int
ahd_acquire_seeprom(struct ahd_softc *ahd)
{
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
/*
* We should be able to determine the SEEPROM type
* from the flexport logic, but unfortunately not
* all implementations have this logic and there is
* no programatic method for determining if the logic
* is present.
*/
return (1);
#if 0
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
uint8_t seetype;
int error;
error = ahd_read_flexport(ahd, FLXADDR_ROMSTAT_CURSENSECTL, &seetype);
if (error != 0
|| ((seetype & FLX_ROMSTAT_SEECFG) == FLX_ROMSTAT_SEE_NONE))
return (0);
return (1);
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
#endif
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
void
ahd_release_seeprom(struct ahd_softc *ahd)
{
/* Currently a no-op */
}
int
ahd_write_flexport(struct ahd_softc *ahd, u_int addr, u_int value)
{
int error;
AHD_ASSERT_MODES(ahd, AHD_MODE_SCSI_MSK, AHD_MODE_SCSI_MSK);
if (addr > 7)
panic("ahd_write_flexport: address out of range");
ahd_outb(ahd, BRDCTL, BRDEN|(addr << 3));
error = ahd_wait_flexport(ahd);
if (error != 0)
return (error);
ahd_outb(ahd, BRDDAT, value);
ahd_flush_device_writes(ahd);
ahd_outb(ahd, BRDCTL, BRDSTB|BRDEN|(addr << 3));
ahd_flush_device_writes(ahd);
ahd_outb(ahd, BRDCTL, BRDEN|(addr << 3));
ahd_flush_device_writes(ahd);
ahd_outb(ahd, BRDCTL, 0);
ahd_flush_device_writes(ahd);
return (0);
}
int
ahd_read_flexport(struct ahd_softc *ahd, u_int addr, uint8_t *value)
{
int error;
AHD_ASSERT_MODES(ahd, AHD_MODE_SCSI_MSK, AHD_MODE_SCSI_MSK);
if (addr > 7)
panic("ahd_read_flexport: address out of range");
ahd_outb(ahd, BRDCTL, BRDRW|BRDEN|(addr << 3));
error = ahd_wait_flexport(ahd);
if (error != 0)
return (error);
*value = ahd_inb(ahd, BRDDAT);
ahd_outb(ahd, BRDCTL, 0);
ahd_flush_device_writes(ahd);
return (0);
}
/*
* Wait at most 2 seconds for flexport arbitration to succeed.
*/
int
ahd_wait_flexport(struct ahd_softc *ahd)
{
int cnt;
AHD_ASSERT_MODES(ahd, AHD_MODE_SCSI_MSK, AHD_MODE_SCSI_MSK);
cnt = 1000000 * 2 / 5;
while ((ahd_inb(ahd, BRDCTL) & FLXARBACK) == 0 && --cnt)
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
aic_delay(5);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
if (cnt == 0)
return (ETIMEDOUT);
return (0);
}
/************************* Target Mode ****************************************/
#ifdef AHD_TARGET_MODE
cam_status
ahd_find_tmode_devs(struct ahd_softc *ahd, struct cam_sim *sim, union ccb *ccb,
struct ahd_tmode_tstate **tstate,
struct ahd_tmode_lstate **lstate,
int notfound_failure)
{
if ((ahd->features & AHD_TARGETMODE) == 0)
return (CAM_REQ_INVALID);
/*
* Handle the 'black hole' device that sucks up
* requests to unattached luns on enabled targets.
*/
if (ccb->ccb_h.target_id == CAM_TARGET_WILDCARD
&& ccb->ccb_h.target_lun == CAM_LUN_WILDCARD) {
*tstate = NULL;
*lstate = ahd->black_hole;
} else {
u_int max_id;
max_id = (ahd->features & AHD_WIDE) ? 15 : 7;
if (ccb->ccb_h.target_id > max_id)
return (CAM_TID_INVALID);
if (ccb->ccb_h.target_lun >= AHD_NUM_LUNS)
return (CAM_LUN_INVALID);
*tstate = ahd->enabled_targets[ccb->ccb_h.target_id];
*lstate = NULL;
if (*tstate != NULL)
*lstate =
(*tstate)->enabled_luns[ccb->ccb_h.target_lun];
}
if (notfound_failure != 0 && *lstate == NULL)
return (CAM_PATH_INVALID);
return (CAM_REQ_CMP);
}
void
ahd_handle_en_lun(struct ahd_softc *ahd, struct cam_sim *sim, union ccb *ccb)
{
#if NOT_YET
struct ahd_tmode_tstate *tstate;
struct ahd_tmode_lstate *lstate;
struct ccb_en_lun *cel;
cam_status status;
u_int target;
u_int lun;
u_int target_mask;
u_long s;
char channel;
status = ahd_find_tmode_devs(ahd, sim, ccb, &tstate, &lstate,
/*notfound_failure*/FALSE);
if (status != CAM_REQ_CMP) {
ccb->ccb_h.status = status;
return;
}
if ((ahd->features & AHD_MULTIROLE) != 0) {
u_int our_id;
our_id = ahd->our_id;
if (ccb->ccb_h.target_id != our_id) {
if ((ahd->features & AHD_MULTI_TID) != 0
&& (ahd->flags & AHD_INITIATORROLE) != 0) {
/*
* Only allow additional targets if
* the initiator role is disabled.
* The hardware cannot handle a re-select-in
* on the initiator id during a re-select-out
* on a different target id.
*/
status = CAM_TID_INVALID;
} else if ((ahd->flags & AHD_INITIATORROLE) != 0
|| ahd->enabled_luns > 0) {
/*
* Only allow our target id to change
* if the initiator role is not configured
* and there are no enabled luns which
* are attached to the currently registered
* scsi id.
*/
status = CAM_TID_INVALID;
}
}
}
if (status != CAM_REQ_CMP) {
ccb->ccb_h.status = status;
return;
}
/*
* We now have an id that is valid.
* If we aren't in target mode, switch modes.
*/
if ((ahd->flags & AHD_TARGETROLE) == 0
&& ccb->ccb_h.target_id != CAM_TARGET_WILDCARD) {
u_long s;
printf("Configuring Target Mode\n");
ahd_lock(ahd, &s);
if (LIST_FIRST(&ahd->pending_scbs) != NULL) {
ccb->ccb_h.status = CAM_BUSY;
ahd_unlock(ahd, &s);
return;
}
ahd->flags |= AHD_TARGETROLE;
if ((ahd->features & AHD_MULTIROLE) == 0)
ahd->flags &= ~AHD_INITIATORROLE;
ahd_pause(ahd);
ahd_loadseq(ahd);
aic7770.c: aic79xx.c: aic79xx.h: aic79xx_pci.c: aic7xxx.c: aic7xxx.h: aic7xxx_pci.c: Switch ah?_reset() to take an additional "reinit" argument. Use this instead of init_level to determin if the chip should be fully reinitialized after a chip reset. This is required so that ah?_shutdown() can reset the chip without side-effects. aic79xx.c: Implement ahd_suspend() and ahd_resume(). aic7xxx.c: Change ahc_loadseq() to *not* restart the sequencer. This brings the loadseq behavior in line with that of the 7902 driver and also simplifies the init routine. Correct the resume routine to enable interrupts and restart the sequencer.
2003-06-06 23:48:19 +00:00
ahd_restart(ahd);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_unlock(ahd, &s);
}
cel = &ccb->cel;
target = ccb->ccb_h.target_id;
lun = ccb->ccb_h.target_lun;
channel = SIM_CHANNEL(ahd, sim);
target_mask = 0x01 << target;
if (channel == 'B')
target_mask <<= 8;
if (cel->enable != 0) {
u_int scsiseq1;
/* Are we already enabled?? */
if (lstate != NULL) {
xpt_print_path(ccb->ccb_h.path);
printf("Lun already enabled\n");
ccb->ccb_h.status = CAM_LUN_ALRDY_ENA;
return;
}
if (cel->grp6_len != 0
|| cel->grp7_len != 0) {
/*
* Don't (yet?) support vendor
* specific commands.
*/
ccb->ccb_h.status = CAM_REQ_INVALID;
printf("Non-zero Group Codes\n");
return;
}
/*
* Seems to be okay.
* Setup our data structures.
*/
if (target != CAM_TARGET_WILDCARD && tstate == NULL) {
tstate = ahd_alloc_tstate(ahd, target, channel);
if (tstate == NULL) {
xpt_print_path(ccb->ccb_h.path);
printf("Couldn't allocate tstate\n");
ccb->ccb_h.status = CAM_RESRC_UNAVAIL;
return;
}
}
lstate = malloc(sizeof(*lstate), M_DEVBUF, M_NOWAIT);
if (lstate == NULL) {
xpt_print_path(ccb->ccb_h.path);
printf("Couldn't allocate lstate\n");
ccb->ccb_h.status = CAM_RESRC_UNAVAIL;
return;
}
memset(lstate, 0, sizeof(*lstate));
status = xpt_create_path(&lstate->path, /*periph*/NULL,
xpt_path_path_id(ccb->ccb_h.path),
xpt_path_target_id(ccb->ccb_h.path),
xpt_path_lun_id(ccb->ccb_h.path));
if (status != CAM_REQ_CMP) {
free(lstate, M_DEVBUF);
xpt_print_path(ccb->ccb_h.path);
printf("Couldn't allocate path\n");
ccb->ccb_h.status = CAM_RESRC_UNAVAIL;
return;
}
SLIST_INIT(&lstate->accept_tios);
SLIST_INIT(&lstate->immed_notifies);
ahd_lock(ahd, &s);
ahd_pause(ahd);
if (target != CAM_TARGET_WILDCARD) {
tstate->enabled_luns[lun] = lstate;
ahd->enabled_luns++;
if ((ahd->features & AHD_MULTI_TID) != 0) {
u_int targid_mask;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
targid_mask = ahd_inw(ahd, TARGID);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
targid_mask |= target_mask;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
ahd_outw(ahd, TARGID, targid_mask);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_update_scsiid(ahd, targid_mask);
} else {
u_int our_id;
char channel;
channel = SIM_CHANNEL(ahd, sim);
our_id = SIM_SCSI_ID(ahd, sim);
/*
* This can only happen if selections
* are not enabled
*/
if (target != our_id) {
u_int sblkctl;
char cur_channel;
int swap;
sblkctl = ahd_inb(ahd, SBLKCTL);
cur_channel = (sblkctl & SELBUSB)
? 'B' : 'A';
if ((ahd->features & AHD_TWIN) == 0)
cur_channel = 'A';
swap = cur_channel != channel;
ahd->our_id = target;
if (swap)
ahd_outb(ahd, SBLKCTL,
sblkctl ^ SELBUSB);
ahd_outb(ahd, SCSIID, target);
if (swap)
ahd_outb(ahd, SBLKCTL, sblkctl);
}
}
} else
ahd->black_hole = lstate;
/* Allow select-in operations */
if (ahd->black_hole != NULL && ahd->enabled_luns > 0) {
scsiseq1 = ahd_inb(ahd, SCSISEQ_TEMPLATE);
scsiseq1 |= ENSELI;
ahd_outb(ahd, SCSISEQ_TEMPLATE, scsiseq1);
scsiseq1 = ahd_inb(ahd, SCSISEQ1);
scsiseq1 |= ENSELI;
ahd_outb(ahd, SCSISEQ1, scsiseq1);
}
ahd_unpause(ahd);
ahd_unlock(ahd, &s);
ccb->ccb_h.status = CAM_REQ_CMP;
xpt_print_path(ccb->ccb_h.path);
printf("Lun now enabled for target mode\n");
} else {
struct scb *scb;
int i, empty;
if (lstate == NULL) {
ccb->ccb_h.status = CAM_LUN_INVALID;
return;
}
ahd_lock(ahd, &s);
ccb->ccb_h.status = CAM_REQ_CMP;
LIST_FOREACH(scb, &ahd->pending_scbs, pending_links) {
struct ccb_hdr *ccbh;
ccbh = &scb->io_ctx->ccb_h;
if (ccbh->func_code == XPT_CONT_TARGET_IO
&& !xpt_path_comp(ccbh->path, ccb->ccb_h.path)){
printf("CTIO pending\n");
ccb->ccb_h.status = CAM_REQ_INVALID;
ahd_unlock(ahd, &s);
return;
}
}
if (SLIST_FIRST(&lstate->accept_tios) != NULL) {
printf("ATIOs pending\n");
ccb->ccb_h.status = CAM_REQ_INVALID;
}
if (SLIST_FIRST(&lstate->immed_notifies) != NULL) {
printf("INOTs pending\n");
ccb->ccb_h.status = CAM_REQ_INVALID;
}
if (ccb->ccb_h.status != CAM_REQ_CMP) {
ahd_unlock(ahd, &s);
return;
}
xpt_print_path(ccb->ccb_h.path);
printf("Target mode disabled\n");
xpt_free_path(lstate->path);
free(lstate, M_DEVBUF);
ahd_pause(ahd);
/* Can we clean up the target too? */
if (target != CAM_TARGET_WILDCARD) {
tstate->enabled_luns[lun] = NULL;
ahd->enabled_luns--;
for (empty = 1, i = 0; i < 8; i++)
if (tstate->enabled_luns[i] != NULL) {
empty = 0;
break;
}
if (empty) {
ahd_free_tstate(ahd, target, channel,
/*force*/FALSE);
if (ahd->features & AHD_MULTI_TID) {
u_int targid_mask;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
targid_mask = ahd_inw(ahd, TARGID);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
targid_mask &= ~target_mask;
ahc_eisa.c: ahc_pci.c: ahd_pci.c: aic7xxx.c: aic79xx.c: aic_osm_lib.c: aic_osm_lib.h: Use common OSM routines from aic_osm_lib for bus dma operations, delay routines, accessing CCBs, byte swapping, etc. aic7xxx_pci.c: Provide a better description for the 2915/30LP on attach. aic7xxx.c: aic79xx.c: aic7770.c: aic79xx_pci.c: aic7xxx_pci.c: aic7xxx_93cx6.c: Move FBSDID behind an ifdef so that these core files will still compile under other OSes. aic79xx.h: aic79xx_pci.c: aic79xx.seq: To speed up non-packetized CDB delivery in Rev B, all CDB acks are "released" to the output sync as soon as the command phase starts. There is only one problem with this approach. If the target changes phase before all data are sent, we have left over acks that can go out on the bus in a data phase. Due to other chip contraints, this only happens if the target goes to data-in, but if the acks go out before we can test SDONE, we'll think that the transfer has completed successfully. Work around this by taking advantage of the 400ns or 800ns dead time between command phase and the REQ of the new phase. If the transfer has completed successfully, SCSIEN should fall *long* before we see a phase change. We thus treat any phasemiss that occurs before SCSIEN falls as an incomplete transfer. aic79xx.h: Add the AHD_FAST_CDB_DELIVERY feature. aic79xx_pci.c: Set AHD_FAST_CDB_DELIVERY for all Rev. B parts. aic79xx.seq: Test for PHASEMIS in the command phase for all AHD_FAST_CDB_DELIVERY controlelrs. ahd_pci.c: ahc_pci.c: aic7xxx.h: aic79xx.h: Move definition of controller BAR offsets to core header files. aic7xxx.c: aic79xx.c: In the softc free routine, leave removal of a softc from the global list of softcs to the OSM (the caller of this routine). This allows us to avoid holding the softc list_lock during device destruction where we may have to sleep waiting for our recovery thread to halt. ahc_pci.c: Use ahc_pci_test_register access to validate I/O mapped in addition to the tests already performed for memory mapped access. Remove unused ahc_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. ahd_pci.c: Remove reduntant definition of controller BAR offsets. These are also defined in aic79xx.h. Remove unused ahd_power_state_change() function. The PCI layer in both 4.X and 5.X now offer this functionality. aic7xxx.c: aic79xx.c: aic79xx.h: aic7xxx.h: aic7xxx_osm.c: aic79xx_osm.c: Move timeout handling to the driver cores. In the case of the aic79xx driver, the algorithm has been enhanced to try target resets before performing a bus reset. For the aic7xxx driver, the algorithm is unchanged. Although the drivers do not currently sleep during recovery (recovery is timeout driven), the cores do expect all processing to be performed via a recovery thread. Our timeout handlers are now little stubs that wakeup the recovery thread. aic79xx.c: aic79xx.h: aic79xx_inline.h: Change shared_data allocation to use a map_node so that the sentinel hscb can use this map node in ahd_swap_with_next_hscb. This routine now swaps the hscb_map pointer in additon to the hscb contents so that any sync operations occur on the correct map. physaddr -> busaddr Pointed out by: Jason Thorpe <thorpej@wasabisystems.com> aic79xx.c: Make more use of the in/out/w/l/q macros for accessing byte registers in the chip. Correct some issues in the ahd_flush_qoutfifo() routine. o Run the qoutfifo only once the command channel DMA engine has been halted. This closes a window where we might have missed some entries. o Change ahd_run_data_fifo() to not loop to completion. If we happen to start on the wrong FIFO and the other FIFO has a snapshot savepointers, we might deadlock. This required our delay between FIFO tests to be moved to the ahd_flush_qoutfifo() routine. o Update/add comments. o Remove spurious test for COMPLETE_DMA list being empty when completing transactions from the GSFIFO with residuals. The SCB must be put on the COMPLETE_DMA scb list unconditionally. o When halting command channel DMA activity, we must disable the DMA channel in all cases but an update of the QOUTFIFO. The latter case is required so that the sequencer will update its position in the QOUTFIFO. Previously, we left the channel enabled for all "push" DMAs. This left us vulnerable to the sequencer handling an SCB push long after that SCB was already processed manually by this routine. o Correct the polarity of tests involving ahd_scb_active_in_fifo(). This routine returns non-zero for true. Return to processing bad status completions through the qoutfifo. This reduces the time that the sequencer is kept paused when handling transactions with bad status or underruns. When waiting for the controller to quiece selections, add a delay to our loop. Otherwise we may fail to wait long enough for the sequencer to comply. On H2A4 hardware, use the slow slewrate for non-paced transfers. This mirrors what the Adaptec Windows drivers do. On the Rev B. only slow down the CRC timing for older U160 devices that might need the slower timing. We define "older" as devices that do not support packetized protocol. Wait up to 5000 * 5us for the SEEPROM to become unbusy. Write ops seem to take much longer than read ops. aic79xx.seq: For controllers with the FAINT_LED bug, turn the diagnostic led feature on during selection and reselection. This covers the non-packetized case. The LED will be disabled for non-packetized transfers once we return to the top level idle loop. Add more comments about the busy LED workaround. Extend a critical section around the entire command channel idle loop process. Previously the portion of this handler that directly manipulated the linked list of completed SCBs was not protected. This is the likely cause of the recent reports of commands being completed twice by the driver. Extend critical sections across the test for, and the longjump to, longjump routines. This prevents the firmware from trying to jump to a longjmp handler that was just cleared by the host. Improve the locations of several critical section begin and end points. Typically these changes remove instructions that did not need to be inside a critical section. Close the "busfree after selection, but before busfree interrupts can be enabled" race to just a single sequencer instruction. We now test the BSY line explicitly before clearing the busfree status and enabling the busfree interrupt. Close a race condition in the processing of HS_MAILBOX updates. We now clear the "updated" status before the copy. This ensures that we don't accidentally clear the status incorrectly when the host sneaks in an update just after our last copy, but before we clear the status. This race has never been observed. Don't re-enable SCSIEN if we lose the race to disable SCSIEN in our interrupt handler's workaround for the RevA data-valid too early issue. aic79xx_inline.h: Add comments indicating that the order in which bytes are read or written in ahd_inw and ahd_outw is important. This allows us to use these inlines when accessing registers with side-effects. aic79xx_pci.c: The 29320 and the 29320B are 7902 not 7901 based products. Correct the driver banner. aic7xxx.h: Enable the use of the auto-access pause feature on the aic7870 and aic7880. It was disabled due to an oversight. aic7xxx.reg: Move TARG_IMMEDIATE_SCB to alias LAST_MSG to avoid leaving garbage in MWI_RESIDUAL. This prevents spurious overflows whn operating target mode on controllers that require the MWI_RESIDUAL work-around. aic7xxx.seq: AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag. Reference the correct softc field when testing for its presence. Set the NOT_IDENTIFIED and NO_CDB_SENT bits in SEQ_FLAGS to indicate that the nexus is invalid in await busfree. aic7xxx_93cx6.c: Add support for the C56/C66 versions of the EWEN and EWDS commands. aic7xxx.c: aic7xxx_pci.c: Move test for the validity of left over BIOS data to ahc_test_register_access(). This guarantees that any left over CHIPRST value is not clobbered by our register access test and lost to the test that was in ahc_reset.
2003-12-17 00:02:10 +00:00
ahd_outw(ahd, TARGID, targid_mask);
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
ahd_update_scsiid(ahd, targid_mask);
}
}
} else {
ahd->black_hole = NULL;
/*
* We can't allow selections without
* our black hole device.
*/
empty = TRUE;
}
if (ahd->enabled_luns == 0) {
/* Disallow select-in */
u_int scsiseq1;
scsiseq1 = ahd_inb(ahd, SCSISEQ_TEMPLATE);
scsiseq1 &= ~ENSELI;
ahd_outb(ahd, SCSISEQ_TEMPLATE, scsiseq1);
scsiseq1 = ahd_inb(ahd, SCSISEQ1);
scsiseq1 &= ~ENSELI;
ahd_outb(ahd, SCSISEQ1, scsiseq1);
if ((ahd->features & AHD_MULTIROLE) == 0) {
printf("Configuring Initiator Mode\n");
ahd->flags &= ~AHD_TARGETROLE;
ahd->flags |= AHD_INITIATORROLE;
ahd_pause(ahd);
ahd_loadseq(ahd);
aic7770.c: aic79xx.c: aic79xx.h: aic79xx_pci.c: aic7xxx.c: aic7xxx.h: aic7xxx_pci.c: Switch ah?_reset() to take an additional "reinit" argument. Use this instead of init_level to determin if the chip should be fully reinitialized after a chip reset. This is required so that ah?_shutdown() can reset the chip without side-effects. aic79xx.c: Implement ahd_suspend() and ahd_resume(). aic7xxx.c: Change ahc_loadseq() to *not* restart the sequencer. This brings the loadseq behavior in line with that of the 7902 driver and also simplifies the init routine. Correct the resume routine to enable interrupts and restart the sequencer.
2003-06-06 23:48:19 +00:00
ahd_restart(ahd);
/*
* Unpaused. The extra unpause
* that follows is harmless.
*/
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
}
}
ahd_unpause(ahd);
ahd_unlock(ahd, &s);
}
#endif
}
static void
ahd_update_scsiid(struct ahd_softc *ahd, u_int targid_mask)
{
#if NOT_YET
u_int scsiid_mask;
u_int scsiid;
if ((ahd->features & AHD_MULTI_TID) == 0)
panic("ahd_update_scsiid called on non-multitid unit\n");
/*
Identify the AIC7901A as such instead of an AIC7902. Push protocol violation handler to its own routine. We now properly detect and recovery from the following target induced protocol violations: o Unexpected or invalid non-packetized Relesection o Command complete with no status message o Good Status after incomplete cdb transfer Add an SCB collision avoidance algorithm that allows us to use all 512 SCBs for non-packetized operations. There is still the possibility of running out of SCBs with non-colliding tag identifiers, but the algorithm ensures that the stall will be rare and short lived. Convert to a read-only algorithm for validing entries in the qoufifo. The sequencer now toggles the high bit of the SCB identifier on each wrap around of the qinfifo. If the high bit doesn't match the expected value for this pass of the qoufifo, the entry is not valid. This has the benefit of working on machines that have large granularity cache write back semantics without requiring any additional memory. Remove lots of code related to untagged SCB queues. Since these controllers can keep a fully busy target table, we will never have untagged SCB queues. Lots of improvements to diagnostic logging. Clarify some comments. Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO handler. Just clearing the interrupt status is sufficient and this avoids the chance of disabling busfree detection in connection that occurs while we are handling the busfree interrupt. Clear all possible interrupt sources when handling a busfree interrupt. The hardware clears some but not all of them. Don't panic if we get into the default SCSIINT handler. Dump the card state and clear all interrupt sources in the hope that we can continue. LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing against values in the PERRDIAG register. According to SPI4, the bus free that is required after certain PPR negotiations will only occur at the end of all message phases. Handle the bus free if it occurs after a transaction in either the message-in or message-out phases. The busfree can also occur if the status of IU_REQ changes due to a WDTR or SDTR message. We now set the expect busfree flag in ahd_set_syncrate so that it works regardless of message type. Correct a problem with missing certain busfree events. The chip supports single-stepping even if a SCSIINT is pending. This obviates the need to clear all of the SCSI interrupt enables prior to single stepping. Since ENBUSFREE can only be disabled manually and not re-enabled, avoiding touching this bit in the single-step case yields reliable bus free detection. Enhance ahd_clear_intstat to clear all SCSIINT sources. Only use ahd_update_pending_scbs() if we are active on the bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the execution queue if a selection might be in process since the sequencer uses this bit to detect PPR negotiation to a target with an outstanding IU_REQ agreement. Allocate the SCB delivery mechansim's sentinal SCB specially so we don't waste a valid SCB for this task. Move tranceive state settle logic to ahd_chip_init() since this needs to occur after every chip reset, not just the chip reset that happens during primary driver initialization. Correct a bug with transmitting lun information in packetized connections. Restrict busy target table operations to the range of luns that can be used for non-packetized connections. Larger luns can only be accessed in packetized mode. Correct a busy target table addressing bug. Be more careful about how we shutdown the DMA engines during bus reset events. Only freeze the SIMQ once regardless of the number of bus reset events that occur while we are polling for the resets to stop. Don't rely on the sequencer remaining paused() during our reset poll. It is safe for the sequencer to run during this time, and many callers to the bus reset code would need to be modified to make this assumption universally true. Even if we are not going to clobber SCB state when an auto-request sense SCB has a check condition, we must still unfreeze the queue. Re-arrange the BAD STATUS handler to handle this case appropriately. Modify the SCB download size depending on whether long luns are being stored in the SCB. Add ahd_print_register() for pretty printing register diagnostics. Don't trust that the flexport logic to detect the presence of a seeprom is available. It may not be on some motherboard implementations. "the the" -> "the"
2002-08-31 06:48:14 +00:00
* Since we will rely on the TARGID mask
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X SCSI Controller chip.
2002-06-05 19:52:45 +00:00
* for selection enables, ensure that OID
* in SCSIID is not set to some other ID
* that we don't want to allow selections on.
*/
if ((ahd->features & AHD_ULTRA2) != 0)
scsiid = ahd_inb(ahd, SCSIID_ULTRA2);
else
scsiid = ahd_inb(ahd, SCSIID);
scsiid_mask = 0x1 << (scsiid & OID);
if ((targid_mask & scsiid_mask) == 0) {
u_int our_id;
/* ffs counts from 1 */
our_id = ffs(targid_mask);
if (our_id == 0)
our_id = ahd->our_id;
else
our_id--;
scsiid &= TID;
scsiid |= our_id;
}
if ((ahd->features & AHD_ULTRA2) != 0)
ahd_outb(ahd, SCSIID_ULTRA2, scsiid);
else
ahd_outb(ahd, SCSIID, scsiid);
#endif
}
void
ahd_run_tqinfifo(struct ahd_softc *ahd, int paused)
{
struct target_cmd *cmd;
ahd_sync_tqinfifo(ahd, BUS_DMASYNC_POSTREAD);
while ((cmd = &ahd->targetcmds[ahd->tqinfifonext])->cmd_valid != 0) {
/*
* Only advance through the queue if we
* have the resources to process the command.
*/
if (ahd_handle_target_cmd(ahd, cmd) != 0)
break;
cmd->cmd_valid = 0;
ahd_dmamap_sync(ahd, ahd->shared_data_dmat,
ahd->shared_data_dmamap,
ahd_targetcmd_offset(ahd, ahd->tqinfifonext),
sizeof(struct target_cmd),
BUS_DMASYNC_PREREAD);
ahd->tqinfifonext++;
/*
* Lazily update our position in the target mode incoming
* command queue as seen by the sequencer.
*/
if ((ahd->tqinfifonext & (HOST_TQINPOS - 1)) == 1) {
u_int hs_mailbox;
hs_mailbox = ahd_inb(ahd, HS_MAILBOX);
hs_mailbox &= ~HOST_TQINPOS;
hs_mailbox |= ahd->tqinfifonext & HOST_TQINPOS;
ahd_outb(ahd, HS_MAILBOX, hs_mailbox);
}
}
}
static int
ahd_handle_target_cmd(struct ahd_softc *ahd, struct target_cmd *cmd)
{
struct ahd_tmode_tstate *tstate;
struct ahd_tmode_lstate *lstate;
struct ccb_accept_tio *atio;
uint8_t *byte;
int initiator;
int target;
int lun;
initiator = SCSIID_TARGET(ahd, cmd->scsiid);
target = SCSIID_OUR_ID(cmd->scsiid);
lun = (cmd->identify & MSG_IDENTIFY_LUNMASK);
byte = cmd->bytes;
tstate = ahd->enabled_targets[target];
lstate = NULL;
if (tstate != NULL)
lstate = tstate->enabled_luns[lun];
/*
* Commands for disabled luns go to the black hole driver.
*/
if (lstate == NULL)
lstate = ahd->black_hole;
atio = (struct ccb_accept_tio*)SLIST_FIRST(&lstate->accept_tios);
if (atio == NULL) {
ahd->flags |= AHD_TQINFIFO_BLOCKED;
/*
* Wait for more ATIOs from the peripheral driver for this lun.
*/
return (1);
} else
ahd->flags &= ~AHD_TQINFIFO_BLOCKED;
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_TQIN) != 0)
printf("Incoming command from %d for %d:%d%s\n",
initiator, target, lun,
lstate == ahd->black_hole ? "(Black Holed)" : "");
#endif
SLIST_REMOVE_HEAD(&lstate->accept_tios, sim_links.sle);
if (lstate == ahd->black_hole) {
/* Fill in the wildcards */
atio->ccb_h.target_id = target;
atio->ccb_h.target_lun = lun;
}
/*
* Package it up and send it off to
* whomever has this lun enabled.
*/
atio->sense_len = 0;
atio->init_id = initiator;
if (byte[0] != 0xFF) {
/* Tag was included */
atio->tag_action = *byte++;
atio->tag_id = *byte++;
atio->ccb_h.flags = CAM_TAG_ACTION_VALID;
} else {
atio->ccb_h.flags = 0;
}
byte++;
/* Okay. Now determine the cdb size based on the command code */
switch (*byte >> CMD_GROUP_CODE_SHIFT) {
case 0:
atio->cdb_len = 6;
break;
case 1:
case 2:
atio->cdb_len = 10;
break;
case 4:
atio->cdb_len = 16;
break;
case 5:
atio->cdb_len = 12;
break;
case 3:
default:
/* Only copy the opcode. */
atio->cdb_len = 1;
printf("Reserved or VU command code type encountered\n");
break;
}
memcpy(atio->cdb_io.cdb_bytes, byte, atio->cdb_len);
atio->ccb_h.status |= CAM_CDB_RECVD;
if ((cmd->identify & MSG_IDENTIFY_DISCFLAG) == 0) {
/*
* We weren't allowed to disconnect.
* We're hanging on the bus until a
* continue target I/O comes in response
* to this accept tio.
*/
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_TQIN) != 0)
printf("Received Immediate Command %d:%d:%d - %p\n",
initiator, target, lun, ahd->pending_device);
#endif
ahd->pending_device = lstate;
ahd_freeze_ccb((union ccb *)atio);
atio->ccb_h.flags |= CAM_DIS_DISCONNECT;
}
xpt_done((union ccb*)atio);
return (0);
}
#endif
Reference in New Issue Copy Permalink