d/freebsd-dev
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
e5fbad8bca
freebsd-dev/sys/dev/mii/mii_physubr.c

596 lines
14 KiB
C
Raw Normal View History

This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
/* $NetBSD: mii_physubr.c,v 1.5 1999/08/03 19:41:49 drochner Exp $ */
/*-
Move a lot closer to NetBSDs MII support for GigE. Move fxp and nge drivers over to use the new stuff.
2002-04-29 11:57:30 +00:00
* Copyright (c) 1998, 1999, 2000, 2001 The NetBSD Foundation, Inc.
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
* All rights reserved.
*
* This code is derived from software contributed to The NetBSD Foundation
* by Jason R. Thorpe of the Numerical Aerospace Simulation Facility,
* NASA Ames Research Center.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. All advertising materials mentioning features or use of this software
* must display the following acknowledgement:
* This product includes software developed by the NetBSD
* Foundation, Inc. and its contributors.
* 4. Neither the name of The NetBSD Foundation nor the names of its
* contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
* TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
* PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*/
/*
* Subroutines common to all PHYs.
*/
#include <sys/param.h>
#include <sys/systm.h>
#include <sys/kernel.h>
#include <sys/socket.h>
#include <sys/errno.h>
#include <sys/module.h>
#include <sys/bus.h>
#include <net/if.h>
#include <net/if_media.h>
#include <dev/mii/mii.h>
#include <dev/mii/miivar.h>
#include "miibus_if.h"
#if !defined(lint)
static const char rcsid[] =
$Id$ -> $FreeBSD$
1999-08-28 01:08:13 +00:00
"$FreeBSD$";
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
#endif
Moving closer to being able to use NetBSD's generic mii_set_media() function.
2002-04-29 07:18:26 +00:00
/*
* Media to register setting conversion table. Order matters.
*/
const struct mii_media mii_media_table[MII_NMEDIA] = {
/* None */
{ BMCR_ISO, ANAR_CSMA,
0, },
/* 10baseT */
{ BMCR_S10, ANAR_CSMA|ANAR_10,
0, },
/* 10baseT-FDX */
{ BMCR_S10|BMCR_FDX, ANAR_CSMA|ANAR_10_FD,
0, },
/* 100baseT4 */
{ BMCR_S100, ANAR_CSMA|ANAR_T4,
0, },
/* 100baseTX */
{ BMCR_S100, ANAR_CSMA|ANAR_TX,
0, },
/* 100baseTX-FDX */
{ BMCR_S100|BMCR_FDX, ANAR_CSMA|ANAR_TX_FD,
0, },
/* 1000baseX */
{ BMCR_S1000, ANAR_CSMA,
0, },
/* 1000baseX-FDX */
{ BMCR_S1000|BMCR_FDX, ANAR_CSMA,
0, },
/* 1000baseT */
{ BMCR_S1000, ANAR_CSMA,
GTCR_ADV_1000THDX },
/* 1000baseT-FDX */
{ BMCR_S1000, ANAR_CSMA,
GTCR_ADV_1000TFDX },
};
Remove __P.
2002-03-20 02:08:01 +00:00
void mii_phy_auto_timeout(void *);
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
Moving closer to being able to use NetBSD's generic mii_set_media() function.
2002-04-29 07:18:26 +00:00
void
mii_phy_setmedia(struct mii_softc *sc)
{
struct mii_data *mii = sc->mii_pdata;
struct ifmedia_entry *ife = mii->mii_media.ifm_cur;
int bmcr, anar, gtcr;
if (IFM_SUBTYPE(ife->ifm_media) == IFM_AUTO) {
if ((PHY_READ(sc, MII_BMCR) & BMCR_AUTOEN) == 0)
(void) mii_phy_auto(sc, 1);
return;
}
/*
* Table index is stored in the media entry.
*/
Move a lot closer to NetBSDs MII support for GigE. Move fxp and nge drivers over to use the new stuff.
2002-04-29 11:57:30 +00:00
KASSERT(ife->ifm_data >=0 && ife->ifm_data < MII_NMEDIA,
("invalid ife->ifm_data (0x%x) in mii_phy_setmedia",
ife->ifm_data));
Moving closer to being able to use NetBSD's generic mii_set_media() function.
2002-04-29 07:18:26 +00:00
anar = mii_media_table[ife->ifm_data].mm_anar;
bmcr = mii_media_table[ife->ifm_data].mm_bmcr;
gtcr = mii_media_table[ife->ifm_data].mm_gtcr;
if (mii->mii_media.ifm_media & IFM_ETH_MASTER) {
switch (IFM_SUBTYPE(ife->ifm_media)) {
case IFM_1000_T:
gtcr |= GTCR_MAN_MS|GTCR_ADV_MS;
break;
default:
panic("mii_phy_setmedia: MASTER on wrong media");
}
}
if (ife->ifm_media & IFM_LOOP)
bmcr |= BMCR_LOOP;
PHY_WRITE(sc, MII_ANAR, anar);
PHY_WRITE(sc, MII_BMCR, bmcr);
if (sc->mii_flags & MIIF_HAVE_GTCR)
PHY_WRITE(sc, MII_100T2CR, gtcr);
}
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
int
Move a lot closer to NetBSDs MII support for GigE. Move fxp and nge drivers over to use the new stuff.
2002-04-29 11:57:30 +00:00
mii_phy_auto(struct mii_softc *sc, int waitfor)
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
{
int bmsr, i;
Move a lot closer to NetBSDs MII support for GigE. Move fxp and nge drivers over to use the new stuff.
2002-04-29 11:57:30 +00:00
if ((sc->mii_flags & MIIF_DOINGAUTO) == 0) {
/*
* Check for 1000BASE-X. Autonegotiation is a bit
* different on such devices.
*/
if (sc->mii_flags & MIIF_IS_1000X) {
uint16_t anar = 0;
if (sc->mii_extcapabilities & EXTSR_1000XFDX)
anar |= ANAR_X_FD;
if (sc->mii_extcapabilities & EXTSR_1000XHDX)
anar |= ANAR_X_HD;
if (sc->mii_flags & MIIF_DOPAUSE) {
/* XXX Asymmetric vs. symmetric? */
anar |= ANLPAR_X_PAUSE_TOWARDS;
}
PHY_WRITE(sc, MII_ANAR, anar);
} else {
uint16_t anar;
anar = BMSR_MEDIA_TO_ANAR(sc->mii_capabilities) |
ANAR_CSMA;
if (sc->mii_flags & MIIF_DOPAUSE)
anar |= ANAR_FC;
PHY_WRITE(sc, MII_ANAR, anar);
if (sc->mii_flags & MIIF_HAVE_GTCR) {
uint16_t gtcr = 0;
if (sc->mii_extcapabilities & EXTSR_1000TFDX)
gtcr |= GTCR_ADV_1000TFDX;
if (sc->mii_extcapabilities & EXTSR_1000THDX)
gtcr |= GTCR_ADV_1000THDX;
PHY_WRITE(sc, MII_100T2CR, gtcr);
}
}
PHY_WRITE(sc, MII_BMCR, BMCR_AUTOEN | BMCR_STARTNEG);
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
}
if (waitfor) {
/* Wait 500ms for it to complete. */
for (i = 0; i < 500; i++) {
Move a lot closer to NetBSDs MII support for GigE. Move fxp and nge drivers over to use the new stuff.
2002-04-29 11:57:30 +00:00
if ((bmsr = PHY_READ(sc, MII_BMSR)) & BMSR_ACOMP)
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
return (0);
DELAY(1000);
}
/*
* Don't need to worry about clearing MIIF_DOINGAUTO.
* If that's set, a timeout is pending, and it will
* clear the flag.
*/
return (EIO);
}
/*
* Just let it finish asynchronously. This is for the benefit of
* the tick handler driving autonegotiation. Don't want 500ms
* delays all the time while the system is running!
*/
Move a lot closer to NetBSDs MII support for GigE. Move fxp and nge drivers over to use the new stuff.
2002-04-29 11:57:30 +00:00
if ((sc->mii_flags & MIIF_DOINGAUTO) == 0) {
sc->mii_flags |= MIIF_DOINGAUTO;
sc->mii_auto_ch = timeout(mii_phy_auto_timeout, sc, hz >> 1);
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
}
return (EJUSTRETURN);
}
void
Move a lot closer to NetBSDs MII support for GigE. Move fxp and nge drivers over to use the new stuff.
2002-04-29 11:57:30 +00:00
mii_phy_auto_timeout(void *arg)
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
{
Move a lot closer to NetBSDs MII support for GigE. Move fxp and nge drivers over to use the new stuff.
2002-04-29 11:57:30 +00:00
struct mii_softc *sc = arg;
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
int s, bmsr;
#if 0
Move a lot closer to NetBSDs MII support for GigE. Move fxp and nge drivers over to use the new stuff.
2002-04-29 11:57:30 +00:00
if ((sc->mii_dev.dv_flags & DVF_ACTIVE) == 0)
return;
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
#endif
Move a lot closer to NetBSDs MII support for GigE. Move fxp and nge drivers over to use the new stuff.
2002-04-29 11:57:30 +00:00
s = splnet();
sc->mii_flags &= ~MIIF_DOINGAUTO;
bmsr = PHY_READ(sc, MII_BMSR);
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
/* Update the media status. */
Move a lot closer to NetBSDs MII support for GigE. Move fxp and nge drivers over to use the new stuff.
2002-04-29 11:57:30 +00:00
(void) (*sc->mii_service)(sc, sc->mii_pdata, MII_POLLSTAT);
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
splx(s);
}
Add new device method miibus_linkchg, along with a service routine.
2001-09-29 18:40:06 +00:00
int
Move a lot closer to NetBSDs MII support for GigE. Move fxp and nge drivers over to use the new stuff.
2002-04-29 11:57:30 +00:00
mii_phy_tick(struct mii_softc *sc)
Add new device method miibus_linkchg, along with a service routine.
2001-09-29 18:40:06 +00:00
{
struct ifmedia_entry *ife = sc->mii_pdata->mii_media.ifm_cur;
struct ifnet *ifp = sc->mii_pdata->mii_ifp;
int reg;
Move a lot closer to NetBSDs MII support for GigE. Move fxp and nge drivers over to use the new stuff.
2002-04-29 11:57:30 +00:00
/* Just bail now if the interface is down. */
Add new device method miibus_linkchg, along with a service routine.
2001-09-29 18:40:06 +00:00
if ((ifp->if_flags & IFF_UP) == 0)
return (EJUSTRETURN);
/*
* If we're not doing autonegotiation, we don't need to do
* any extra work here. However, we need to check the link
* status so we can generate an announcement if the status
* changes.
*/
if (IFM_SUBTYPE(ife->ifm_media) != IFM_AUTO)
return (0);
Move a lot closer to NetBSDs MII support for GigE. Move fxp and nge drivers over to use the new stuff.
2002-04-29 11:57:30 +00:00
/* Read the status register twice; BMSR_LINK is latch-low. */
Add new device method miibus_linkchg, along with a service routine.
2001-09-29 18:40:06 +00:00
reg = PHY_READ(sc, MII_BMSR) | PHY_READ(sc, MII_BMSR);
Move a lot closer to NetBSDs MII support for GigE. Move fxp and nge drivers over to use the new stuff.
2002-04-29 11:57:30 +00:00
if (reg & BMSR_LINK) {
/*
* See above.
*/
Add new device method miibus_linkchg, along with a service routine.
2001-09-29 18:40:06 +00:00
return (0);
Move a lot closer to NetBSDs MII support for GigE. Move fxp and nge drivers over to use the new stuff.
2002-04-29 11:57:30 +00:00
}
Add new device method miibus_linkchg, along with a service routine.
2001-09-29 18:40:06 +00:00
/*
Move a lot closer to NetBSDs MII support for GigE. Move fxp and nge drivers over to use the new stuff.
2002-04-29 11:57:30 +00:00
* Only retry autonegotiation every N seconds.
Add new device method miibus_linkchg, along with a service routine.
2001-09-29 18:40:06 +00:00
*/
Move a lot closer to NetBSDs MII support for GigE. Move fxp and nge drivers over to use the new stuff.
2002-04-29 11:57:30 +00:00
if (sc->mii_anegticks == 0)
sc->mii_anegticks = 5;
if (++sc->mii_ticks != sc->mii_anegticks)
Add new device method miibus_linkchg, along with a service routine.
2001-09-29 18:40:06 +00:00
return (EJUSTRETURN);
sc->mii_ticks = 0;
mii_phy_reset(sc);
if (mii_phy_auto(sc, 0) == EJUSTRETURN)
return (EJUSTRETURN);
/*
* Might need to generate a status message if autonegotiation
* failed.
*/
return (0);
}
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
void
Move a lot closer to NetBSDs MII support for GigE. Move fxp and nge drivers over to use the new stuff.
2002-04-29 11:57:30 +00:00
mii_phy_reset(struct mii_softc *sc)
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
{
int reg, i;
Move a lot closer to NetBSDs MII support for GigE. Move fxp and nge drivers over to use the new stuff.
2002-04-29 11:57:30 +00:00
if (sc->mii_flags & MIIF_NOISOLATE)
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
reg = BMCR_RESET;
else
reg = BMCR_RESET | BMCR_ISO;
Move a lot closer to NetBSDs MII support for GigE. Move fxp and nge drivers over to use the new stuff.
2002-04-29 11:57:30 +00:00
PHY_WRITE(sc, MII_BMCR, reg);
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
/* Wait 100ms for it to complete. */
for (i = 0; i < 100; i++) {
Move a lot closer to NetBSDs MII support for GigE. Move fxp and nge drivers over to use the new stuff.
2002-04-29 11:57:30 +00:00
reg = PHY_READ(sc, MII_BMCR);
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
if ((reg & BMCR_RESET) == 0)
break;
DELAY(1000);
}
Move a lot closer to NetBSDs MII support for GigE. Move fxp and nge drivers over to use the new stuff.
2002-04-29 11:57:30 +00:00
if (sc->mii_inst != 0 && ((sc->mii_flags & MIIF_NOISOLATE) == 0))
PHY_WRITE(sc, MII_BMCR, reg | BMCR_ISO);
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
}
Add new device method miibus_linkchg, along with a service routine.
2001-09-29 18:40:06 +00:00
void
Make one generic mii_phy_detach() to replace 19 slightly different ones. Rename mii_phy_auto_stop() mii_phy_down(). Introduce mii_down(), use it from nge. Do not indirect it to 19 identical case's in 19 switchstatements like NetBSD did.
2002-04-29 13:07:38 +00:00
mii_phy_down(struct mii_softc *sc)
{
if (sc->mii_flags & MIIF_DOINGAUTO) {
sc->mii_flags &= ~MIIF_DOINGAUTO;
untimeout(mii_phy_auto_timeout, sc, sc->mii_auto_ch);
}
}
void
mii_phy_update(struct mii_softc *sc, int cmd)
Add new device method miibus_linkchg, along with a service routine.
2001-09-29 18:40:06 +00:00
{
struct mii_data *mii = sc->mii_pdata;
Make one generic mii_phy_detach() to replace 19 slightly different ones. Rename mii_phy_auto_stop() mii_phy_down(). Introduce mii_down(), use it from nge. Do not indirect it to 19 identical case's in 19 switchstatements like NetBSD did.
2002-04-29 13:07:38 +00:00
if (sc->mii_media_active != mii->mii_media_active ||
cmd == MII_MEDIACHG) {
Add new device method miibus_linkchg, along with a service routine.
2001-09-29 18:40:06 +00:00
MIIBUS_STATCHG(sc->mii_dev);
Edging ever closer to NetBSD...
2002-04-29 06:48:20 +00:00
sc->mii_media_active = mii->mii_media_active;
Add new device method miibus_linkchg, along with a service routine.
2001-09-29 18:40:06 +00:00
}
Edging ever closer to NetBSD...
2002-04-29 06:48:20 +00:00
if (sc->mii_media_status != mii->mii_media_status) {
Add new device method miibus_linkchg, along with a service routine.
2001-09-29 18:40:06 +00:00
MIIBUS_LINKCHG(sc->mii_dev);
Edging ever closer to NetBSD...
2002-04-29 06:48:20 +00:00
sc->mii_media_status = mii->mii_media_status;
Add new device method miibus_linkchg, along with a service routine.
2001-09-29 18:40:06 +00:00
}
}
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
/*
* Given an ifmedia word, return the corresponding ANAR value.
*/
int
mii_anar(media)
int media;
{
int rv;
switch (media & (IFM_TMASK|IFM_NMASK|IFM_FDX)) {
case IFM_ETHER|IFM_10_T:
rv = ANAR_10|ANAR_CSMA;
break;
case IFM_ETHER|IFM_10_T|IFM_FDX:
rv = ANAR_10_FD|ANAR_CSMA;
break;
case IFM_ETHER|IFM_100_TX:
rv = ANAR_TX|ANAR_CSMA;
break;
case IFM_ETHER|IFM_100_TX|IFM_FDX:
rv = ANAR_TX_FD|ANAR_CSMA;
break;
case IFM_ETHER|IFM_100_T4:
rv = ANAR_T4|ANAR_CSMA;
break;
default:
rv = 0;
break;
}
return (rv);
}
/*
* Given a BMCR value, return the corresponding ifmedia word.
*/
int
mii_media_from_bmcr(bmcr)
int bmcr;
{
int rv = IFM_ETHER;
if (bmcr & BMCR_S100)
rv |= IFM_100_TX;
else
rv |= IFM_10_T;
if (bmcr & BMCR_FDX)
rv |= IFM_FDX;
return (rv);
}
/*
* Initialize generic PHY media based on BMSR, called when a PHY is
* attached. We expect to be set up to print a comma-separated list
* of media names. Does not print a newline.
*/
void
Don't pass three args when one will do just fine, and even prevent mistakes like the one brgphy.c (now corrected).
2002-04-28 19:25:07 +00:00
mii_add_media(struct mii_softc *sc)
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
{
const char *sep = "";
Don't pass three args when one will do just fine, and even prevent mistakes like the one brgphy.c (now corrected).
2002-04-28 19:25:07 +00:00
struct mii_data *mii;
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
Don't pass three args when one will do just fine, and even prevent mistakes like the one brgphy.c (now corrected).
2002-04-28 19:25:07 +00:00
mii = device_get_softc(sc->mii_dev);
Moving closer to being able to use NetBSD's generic mii_set_media() function.
2002-04-29 07:18:26 +00:00
if ((sc->mii_capabilities & BMSR_MEDIAMASK) == 0) {
Improve an API by about 4 lines per driver.
2002-04-28 19:01:32 +00:00
printf("no media present");
return;
}
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
#define ADD(m, c) ifmedia_add(&mii->mii_media, (m), (c), NULL)
#define PRINT(s) printf("%s%s", sep, s); sep = ", "
Moving closer to being able to use NetBSD's generic mii_set_media() function.
2002-04-29 07:18:26 +00:00
if (sc->mii_capabilities & BMSR_10THDX) {
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_10_T, 0, sc->mii_inst), 0);
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
PRINT("10baseT");
}
Moving closer to being able to use NetBSD's generic mii_set_media() function.
2002-04-29 07:18:26 +00:00
if (sc->mii_capabilities & BMSR_10TFDX) {
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_10_T, IFM_FDX, sc->mii_inst),
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
BMCR_FDX);
PRINT("10baseT-FDX");
}
Moving closer to being able to use NetBSD's generic mii_set_media() function.
2002-04-29 07:18:26 +00:00
if (sc->mii_capabilities & BMSR_100TXHDX) {
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_100_TX, 0, sc->mii_inst),
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
BMCR_S100);
PRINT("100baseTX");
}
Moving closer to being able to use NetBSD's generic mii_set_media() function.
2002-04-29 07:18:26 +00:00
if (sc->mii_capabilities & BMSR_100TXFDX) {
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_100_TX, IFM_FDX, sc->mii_inst),
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
BMCR_S100|BMCR_FDX);
PRINT("100baseTX-FDX");
}
Moving closer to being able to use NetBSD's generic mii_set_media() function.
2002-04-29 07:18:26 +00:00
if (sc->mii_capabilities & BMSR_100T4) {
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
/*
* XXX How do you enable 100baseT4? I assume we set
* XXX BMCR_S100 and then assume the PHYs will take
* XXX watever action is necessary to switch themselves
* XXX into T4 mode.
*/
Moving closer to being able to use NetBSD's generic mii_set_media() function.
2002-04-29 07:18:26 +00:00
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_100_T4, 0, sc->mii_inst),
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
BMCR_S100);
PRINT("100baseT4");
}
Moving closer to being able to use NetBSD's generic mii_set_media() function.
2002-04-29 07:18:26 +00:00
if (sc->mii_capabilities & BMSR_ANEG) {
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_AUTO, 0, sc->mii_inst),
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
BMCR_AUTOEN);
PRINT("auto");
}
Don't pass three args when one will do just fine, and even prevent mistakes like the one brgphy.c (now corrected).
2002-04-28 19:25:07 +00:00
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
#undef ADD
#undef PRINT
}
Move a lot closer to NetBSDs MII support for GigE. Move fxp and nge drivers over to use the new stuff.
2002-04-29 11:57:30 +00:00
/*
* Initialize generic PHY media based on BMSR, called when a PHY is
* attached. We expect to be set up to print a comma-separated list
* of media names. Does not print a newline.
*/
void
mii_phy_add_media(struct mii_softc *sc)
{
struct mii_data *mii = sc->mii_pdata;
const char *sep = "";
#define ADD(m, c) ifmedia_add(&mii->mii_media, (m), (c), NULL)
#define PRINT(s) printf("%s%s", sep, s); sep = ", "
if ((sc->mii_flags & MIIF_NOISOLATE) == 0)
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_NONE, 0, sc->mii_inst),
MII_MEDIA_NONE);
/*
* There are different interpretations for the bits in
* HomePNA PHYs. And there is really only one media type
* that is supported.
*/
if (sc->mii_flags & MIIF_IS_HPNA) {
if (sc->mii_capabilities & BMSR_10THDX) {
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_HPNA_1, 0,
sc->mii_inst),
MII_MEDIA_10_T);
PRINT("HomePNA1");
}
return;
}
if (sc->mii_capabilities & BMSR_10THDX) {
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_10_T, 0, sc->mii_inst),
MII_MEDIA_10_T);
PRINT("10baseT");
}
if (sc->mii_capabilities & BMSR_10TFDX) {
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_10_T, IFM_FDX, sc->mii_inst),
MII_MEDIA_10_T_FDX);
PRINT("10baseT-FDX");
}
if (sc->mii_capabilities & BMSR_100TXHDX) {
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_100_TX, 0, sc->mii_inst),
MII_MEDIA_100_TX);
PRINT("100baseTX");
}
if (sc->mii_capabilities & BMSR_100TXFDX) {
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_100_TX, IFM_FDX, sc->mii_inst),
MII_MEDIA_100_TX_FDX);
PRINT("100baseTX-FDX");
}
if (sc->mii_capabilities & BMSR_100T4) {
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_100_T4, 0, sc->mii_inst),
MII_MEDIA_100_T4);
PRINT("100baseT4");
}
if (sc->mii_extcapabilities & EXTSR_MEDIAMASK) {
/*
* XXX Right now only handle 1000SX and 1000TX. Need
* XXX to handle 1000LX and 1000CX some how.
*
* Note since it can take 5 seconds to auto-negotiate
* a gigabit link, we make anegticks 10 seconds for
* all the gigabit media types.
*/
if (sc->mii_extcapabilities & EXTSR_1000XHDX) {
sc->mii_anegticks = 10;
sc->mii_flags |= MIIF_IS_1000X;
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_1000_SX, 0,
sc->mii_inst), MII_MEDIA_1000_X);
PRINT("1000baseSX");
}
if (sc->mii_extcapabilities & EXTSR_1000XFDX) {
sc->mii_anegticks = 10;
sc->mii_flags |= MIIF_IS_1000X;
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_1000_SX, IFM_FDX,
sc->mii_inst), MII_MEDIA_1000_X_FDX);
PRINT("1000baseSX-FDX");
}
/*
* 1000baseT media needs to be able to manipulate
* master/slave mode. We set IFM_ETH_MASTER in
* the "don't care mask" and filter it out when
* the media is set.
*
* All 1000baseT PHYs have a 1000baseT control register.
*/
if (sc->mii_extcapabilities & EXTSR_1000THDX) {
sc->mii_anegticks = 10;
sc->mii_flags |= MIIF_HAVE_GTCR;
mii->mii_media.ifm_mask |= IFM_ETH_MASTER;
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_1000_T, 0,
sc->mii_inst), MII_MEDIA_1000_T);
PRINT("1000baseT");
}
if (sc->mii_extcapabilities & EXTSR_1000TFDX) {
sc->mii_anegticks = 10;
sc->mii_flags |= MIIF_HAVE_GTCR;
mii->mii_media.ifm_mask |= IFM_ETH_MASTER;
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_1000_T, IFM_FDX,
sc->mii_inst), MII_MEDIA_1000_T_FDX);
PRINT("1000baseT-FDX");
}
}
if (sc->mii_capabilities & BMSR_ANEG) {
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_AUTO, 0, sc->mii_inst),
MII_NMEDIA); /* intentionally invalid index */
PRINT("auto");
}
#undef ADD
#undef PRINT
}
Make one generic mii_phy_detach() to replace 19 slightly different ones. Rename mii_phy_auto_stop() mii_phy_down(). Introduce mii_down(), use it from nge. Do not indirect it to 19 identical case's in 19 switchstatements like NetBSD did.
2002-04-29 13:07:38 +00:00
int
mii_phy_detach(device_t dev)
{
struct mii_softc *sc;
struct mii_data *mii;
sc = device_get_softc(dev);
mii = device_get_softc(device_get_parent(dev));
mii_phy_down(sc);
sc->mii_dev = NULL;
LIST_REMOVE(sc, mii_list);
return(0);
}
Reference in New Issue Copy Permalink