80 lines
1.9 KiB
Plaintext
80 lines
1.9 KiB
Plaintext
|
|
||
|
|
# $FreeBSD$
|
||
|
|
|
||
|
|
# There's two interfaces, but only one socket is populated.
|
||
|
|
#
|
||
|
|
# There's an AR8021 PHY attached to arge1.
|
||
|
|
#
|
||
|
|
# XXX TODO: figure out where to extract the MAC from.
|
||
|
|
hint.arge.1.phymask=0x01
|
||
|
|
|
||
|
|
# XXX TODO: pass in hints for the GPIO -> LED mapping for the
|
||
|
|
# minipci slot. The specific customer reference design NIC
|
||
|
|
# wires GPIO5 from each AR9220 to one of two GPIO pins on the
|
||
|
|
# MiniPCI bus. However, this may be very specific to the NIC
|
||
|
|
# being used.
|
||
|
|
|
||
|
|
# The default flash layout:
|
||
|
|
# uboot: 192k
|
||
|
|
# env: 64k
|
||
|
|
# rootfs: 6144k
|
||
|
|
# uimage (kernel): 1728k
|
||
|
|
# caldata: 64k
|
||
|
|
#
|
||
|
|
# We steal 64k from the end of rootfs to store the local config.
|
||
|
|
|
||
|
|
hint.map.0.at="flash/spi0"
|
||
|
|
hint.map.0.start=0x00000000
|
||
|
|
hint.map.0.end=0x000030000
|
||
|
|
hint.map.0.name="uboot"
|
||
|
|
hint.map.0.readonly=1
|
||
|
|
|
||
|
|
hint.map.1.at="flash/spi0"
|
||
|
|
hint.map.1.start=0x00030000
|
||
|
|
hint.map.1.end=0x00040000
|
||
|
|
hint.map.1.name="uboot-env"
|
||
|
|
hint.map.1.readonly=1
|
||
|
|
|
||
|
|
hint.map.2.at="flash/spi0"
|
||
|
|
hint.map.2.start=0x00040000
|
||
|
|
hint.map.2.end=0x00630000
|
||
|
|
hint.map.2.name="rootfs"
|
||
|
|
hint.map.2.readonly=1
|
||
|
|
|
||
|
|
hint.map.3.at="flash/spi0"
|
||
|
|
hint.map.3.start=0x00630000
|
||
|
|
hint.map.3.end=0x00640000
|
||
|
|
hint.map.3.name="cfg"
|
||
|
|
hint.map.3.readonly=0
|
||
|
|
|
||
|
|
hint.map.4.at="flash/spi0"
|
||
|
|
hint.map.4.start=0x00640000
|
||
|
|
hint.map.4.end=0x007f0000
|
||
|
|
hint.map.4.name="kernel"
|
||
|
|
hint.map.4.readonly=1
|
||
|
|
|
||
|
|
hint.map.5.at="flash/spi0"
|
||
|
|
hint.map.5.start=0x007f0000
|
||
|
|
hint.map.5.end=0x00800000
|
||
|
|
hint.map.5.name="art"
|
||
|
|
hint.map.5.readonly=1
|
||
|
|
|
||
|
|
# Don't flip on anything that isn't already enabled by the
|
||
|
|
# bootloader.
|
||
|
|
hint.gpio.0.function_set=0x00000000
|
||
|
|
hint.gpio.0.function_clear=0x00000000
|
||
|
|
|
||
|
|
# Which GPIO lines to enable - just GPIO2/3 for the LEDs.
|
||
|
|
hint.gpio.0.pinmask=0x0000000c
|
||
|
|
|
||
|
|
# GPIO2 and GPIO3 are LEDs, where 0=on and 1=off.
|
||
|
|
# XXX TODO: teach gpioled about polarity?
|
||
|
|
hint.gpioled.0.at="gpiobus0"
|
||
|
|
hint.gpioled.0.pins="0x0004"
|
||
|
|
hint.gpioled.0.name="led1"
|
||
|
|
|
||
|
|
hint.gpioled.1.at="gpiobus0"
|
||
|
|
hint.gpioled.1.pins="0x0008"
|
||
|
|
hint.gpioled.1.name="led2"
|
||
|
|
|