Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
/*-
|
|
|
|
* Copyright (c) 2002-2008 Sam Leffler, Errno Consulting
|
|
|
|
* All rights reserved.
|
|
|
|
*
|
|
|
|
* Redistribution and use in source and binary forms, with or without
|
|
|
|
* modification, are permitted provided that the following conditions
|
|
|
|
* are met:
|
|
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
|
|
* notice, this list of conditions and the following disclaimer.
|
|
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
|
|
* documentation and/or other materials provided with the distribution.
|
|
|
|
*
|
|
|
|
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
|
|
|
|
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
|
|
|
|
* OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
|
|
|
|
* IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
|
|
|
|
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
|
|
|
|
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
|
|
|
|
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
|
|
|
|
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
|
|
|
|
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
|
|
|
|
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
|
|
*/
|
|
|
|
|
|
|
|
#include <sys/cdefs.h>
|
|
|
|
/*
|
|
|
|
* IEEE 802.11 scanning support.
|
|
|
|
*/
|
|
|
|
#include "opt_wlan.h"
|
|
|
|
|
|
|
|
#include <sys/param.h>
|
|
|
|
#include <sys/systm.h>
|
|
|
|
#include <sys/proc.h>
|
|
|
|
#include <sys/kernel.h>
|
2016-02-01 17:41:21 +00:00
|
|
|
#include <sys/malloc.h>
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
#include <sys/condvar.h>
|
2020-09-01 21:19:14 +00:00
|
|
|
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
#include <sys/socket.h>
|
|
|
|
|
|
|
|
#include <net/if.h>
|
|
|
|
#include <net/if_var.h>
|
|
|
|
#include <net/if_media.h>
|
2023-01-23 15:05:29 +00:00
|
|
|
#include <net/if_private.h>
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
#include <net/ethernet.h>
|
|
|
|
|
|
|
|
#include <net80211/ieee80211_var.h>
|
|
|
|
|
|
|
|
#include <net80211/ieee80211_scan_sw.h>
|
|
|
|
|
|
|
|
#include <net/bpf.h>
|
|
|
|
|
|
|
|
struct scan_state {
|
|
|
|
struct ieee80211_scan_state base; /* public state */
|
|
|
|
|
2016-02-29 21:03:54 +00:00
|
|
|
u_int ss_iflags; /* flags used internally */
|
|
|
|
#define ISCAN_MINDWELL 0x0001 /* min dwell time reached */
|
|
|
|
#define ISCAN_DISCARD 0x0002 /* discard rx'd frames */
|
2016-09-30 18:43:39 +00:00
|
|
|
#define ISCAN_INTERRUPT 0x0004 /* interrupt current scan */
|
|
|
|
#define ISCAN_CANCEL 0x0008 /* cancel current scan */
|
|
|
|
#define ISCAN_PAUSE (ISCAN_INTERRUPT | ISCAN_CANCEL)
|
|
|
|
#define ISCAN_ABORT 0x0010 /* end the scan immediately */
|
|
|
|
#define ISCAN_RUNNING 0x0020 /* scan was started */
|
2016-02-29 21:03:54 +00:00
|
|
|
|
|
|
|
unsigned long ss_chanmindwell; /* min dwell on curchan */
|
|
|
|
unsigned long ss_scanend; /* time scan must stop */
|
|
|
|
u_int ss_duration; /* duration for next scan */
|
|
|
|
struct task ss_scan_start; /* scan start */
|
|
|
|
struct timeout_task ss_scan_curchan; /* scan execution */
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
};
|
|
|
|
#define SCAN_PRIVATE(ss) ((struct scan_state *) ss)
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Amount of time to go off-channel during a background
|
|
|
|
* scan. This value should be large enough to catch most
|
|
|
|
* ap's but short enough that we can return on-channel
|
|
|
|
* before our listen interval expires.
|
|
|
|
*
|
|
|
|
* XXX tunable
|
|
|
|
* XXX check against configured listen interval
|
|
|
|
*/
|
|
|
|
#define IEEE80211_SCAN_OFFCHANNEL msecs_to_ticks(150)
|
|
|
|
|
|
|
|
static void scan_curchan(struct ieee80211_scan_state *, unsigned long);
|
|
|
|
static void scan_mindwell(struct ieee80211_scan_state *);
|
2016-02-29 21:00:10 +00:00
|
|
|
static void scan_signal(struct ieee80211_scan_state *, int);
|
|
|
|
static void scan_signal_locked(struct ieee80211_scan_state *, int);
|
2016-02-29 20:53:27 +00:00
|
|
|
static void scan_start(void *, int);
|
|
|
|
static void scan_curchan_task(void *, int);
|
2016-02-29 20:47:07 +00:00
|
|
|
static void scan_end(struct ieee80211_scan_state *, int);
|
2016-02-29 20:44:59 +00:00
|
|
|
static void scan_done(struct ieee80211_scan_state *, int);
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
|
|
|
|
MALLOC_DEFINE(M_80211_SCAN, "80211scan", "802.11 scan state");
|
|
|
|
|
2015-06-08 02:35:43 +00:00
|
|
|
static void
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
ieee80211_swscan_detach(struct ieee80211com *ic)
|
|
|
|
{
|
|
|
|
struct ieee80211_scan_state *ss = ic->ic_scan;
|
|
|
|
|
|
|
|
if (ss != NULL) {
|
2016-02-29 21:00:10 +00:00
|
|
|
scan_signal(ss, ISCAN_ABORT);
|
2016-02-29 20:53:27 +00:00
|
|
|
ieee80211_draintask(ic, &SCAN_PRIVATE(ss)->ss_scan_start);
|
|
|
|
taskqueue_drain_timeout(ic->ic_tq,
|
|
|
|
&SCAN_PRIVATE(ss)->ss_scan_curchan);
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
KASSERT((ic->ic_flags & IEEE80211_F_SCAN) == 0,
|
|
|
|
("scan still running"));
|
|
|
|
|
|
|
|
/*
|
|
|
|
* For now, do the ss_ops detach here rather
|
|
|
|
* than ieee80211_scan_detach().
|
|
|
|
*
|
|
|
|
* I'll figure out how to cleanly split things up
|
|
|
|
* at a later date.
|
|
|
|
*/
|
|
|
|
if (ss->ss_ops != NULL) {
|
|
|
|
ss->ss_ops->scan_detach(ss);
|
|
|
|
ss->ss_ops = NULL;
|
|
|
|
}
|
|
|
|
ic->ic_scan = NULL;
|
2015-05-25 19:18:16 +00:00
|
|
|
IEEE80211_FREE(SCAN_PRIVATE(ss), M_80211_SCAN);
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
}
|
|
|
|
}
|
|
|
|
|
2015-06-08 02:35:43 +00:00
|
|
|
static void
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
ieee80211_swscan_vattach(struct ieee80211vap *vap)
|
|
|
|
{
|
|
|
|
/* nothing to do for now */
|
|
|
|
/*
|
|
|
|
* TODO: all of the vap scan calls should be methods!
|
|
|
|
*/
|
|
|
|
|
|
|
|
}
|
|
|
|
|
2015-06-08 02:35:43 +00:00
|
|
|
static void
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
ieee80211_swscan_vdetach(struct ieee80211vap *vap)
|
|
|
|
{
|
|
|
|
struct ieee80211com *ic = vap->iv_ic;
|
2016-02-29 21:03:54 +00:00
|
|
|
struct ieee80211_scan_state *ss = ic->ic_scan;
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
|
|
|
|
IEEE80211_LOCK_ASSERT(ic);
|
2016-02-29 21:03:54 +00:00
|
|
|
|
|
|
|
if (ss != NULL && ss->ss_vap == vap &&
|
|
|
|
(ic->ic_flags & IEEE80211_F_SCAN))
|
|
|
|
scan_signal_locked(ss, ISCAN_ABORT);
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
}
|
|
|
|
|
2015-06-08 02:35:43 +00:00
|
|
|
static void
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
ieee80211_swscan_set_scan_duration(struct ieee80211vap *vap, u_int duration)
|
|
|
|
{
|
|
|
|
struct ieee80211com *ic = vap->iv_ic;
|
|
|
|
struct ieee80211_scan_state *ss = ic->ic_scan;
|
|
|
|
|
|
|
|
IEEE80211_LOCK_ASSERT(ic);
|
|
|
|
|
|
|
|
/* NB: flush frames rx'd before 1st channel change */
|
|
|
|
SCAN_PRIVATE(ss)->ss_iflags |= ISCAN_DISCARD;
|
|
|
|
SCAN_PRIVATE(ss)->ss_duration = duration;
|
|
|
|
}
|
|
|
|
|
2015-05-10 06:59:34 +00:00
|
|
|
/*
|
|
|
|
* Start a scan unless one is already going.
|
|
|
|
*/
|
|
|
|
static int
|
|
|
|
ieee80211_swscan_start_scan_locked(const struct ieee80211_scanner *scan,
|
|
|
|
struct ieee80211vap *vap, int flags, u_int duration,
|
|
|
|
u_int mindwell, u_int maxdwell,
|
|
|
|
u_int nssid, const struct ieee80211_scan_ssid ssids[])
|
|
|
|
{
|
|
|
|
struct ieee80211com *ic = vap->iv_ic;
|
|
|
|
struct ieee80211_scan_state *ss = ic->ic_scan;
|
|
|
|
|
|
|
|
IEEE80211_LOCK_ASSERT(ic);
|
|
|
|
|
|
|
|
if (ic->ic_flags & IEEE80211_F_CSAPENDING) {
|
|
|
|
IEEE80211_DPRINTF(vap, IEEE80211_MSG_SCAN,
|
|
|
|
"%s: scan inhibited by pending channel change\n", __func__);
|
|
|
|
} else if ((ic->ic_flags & IEEE80211_F_SCAN) == 0) {
|
|
|
|
IEEE80211_DPRINTF(vap, IEEE80211_MSG_SCAN,
|
|
|
|
"%s: %s scan, duration %u mindwell %u maxdwell %u, desired mode %s, %s%s%s%s%s%s\n"
|
|
|
|
, __func__
|
|
|
|
, flags & IEEE80211_SCAN_ACTIVE ? "active" : "passive"
|
|
|
|
, duration, mindwell, maxdwell
|
|
|
|
, ieee80211_phymode_name[vap->iv_des_mode]
|
|
|
|
, flags & IEEE80211_SCAN_FLUSH ? "flush" : "append"
|
|
|
|
, flags & IEEE80211_SCAN_NOPICK ? ", nopick" : ""
|
|
|
|
, flags & IEEE80211_SCAN_NOJOIN ? ", nojoin" : ""
|
|
|
|
, flags & IEEE80211_SCAN_NOBCAST ? ", nobcast" : ""
|
|
|
|
, flags & IEEE80211_SCAN_PICK1ST ? ", pick1st" : ""
|
|
|
|
, flags & IEEE80211_SCAN_ONCE ? ", once" : ""
|
|
|
|
);
|
|
|
|
|
|
|
|
ieee80211_scan_update_locked(vap, scan);
|
|
|
|
if (ss->ss_ops != NULL) {
|
|
|
|
if ((flags & IEEE80211_SCAN_NOSSID) == 0)
|
|
|
|
ieee80211_scan_copy_ssid(vap, ss, nssid, ssids);
|
|
|
|
|
2023-03-14 21:00:48 +00:00
|
|
|
ss->ss_flags = flags & IEEE80211_SCAN_PUBLIC_MASK;
|
2015-05-10 06:59:34 +00:00
|
|
|
if (ss->ss_flags & IEEE80211_SCAN_ACTIVE)
|
|
|
|
vap->iv_stats.is_scan_active++;
|
|
|
|
else
|
|
|
|
vap->iv_stats.is_scan_passive++;
|
|
|
|
if (flags & IEEE80211_SCAN_FLUSH)
|
|
|
|
ss->ss_ops->scan_flush(ss);
|
|
|
|
if (flags & IEEE80211_SCAN_BGSCAN)
|
|
|
|
ic->ic_flags_ext |= IEEE80211_FEXT_BGSCAN;
|
|
|
|
|
|
|
|
/* Set duration for this particular scan */
|
|
|
|
ieee80211_swscan_set_scan_duration(vap, duration);
|
|
|
|
|
|
|
|
ss->ss_next = 0;
|
|
|
|
ss->ss_mindwell = mindwell;
|
|
|
|
ss->ss_maxdwell = maxdwell;
|
|
|
|
/* NB: scan_start must be before the scan runtask */
|
|
|
|
ss->ss_ops->scan_start(ss, vap);
|
|
|
|
#ifdef IEEE80211_DEBUG
|
|
|
|
if (ieee80211_msg_scan(vap))
|
|
|
|
ieee80211_scan_dump(ss);
|
|
|
|
#endif /* IEEE80211_DEBUG */
|
|
|
|
ic->ic_flags |= IEEE80211_F_SCAN;
|
|
|
|
|
|
|
|
/* Start scan task */
|
2016-02-29 20:53:27 +00:00
|
|
|
ieee80211_runtask(ic, &SCAN_PRIVATE(ss)->ss_scan_start);
|
2015-05-10 06:59:34 +00:00
|
|
|
}
|
|
|
|
return 1;
|
|
|
|
} else {
|
|
|
|
IEEE80211_DPRINTF(vap, IEEE80211_MSG_SCAN,
|
|
|
|
"%s: %s scan already in progress\n", __func__,
|
|
|
|
ss->ss_flags & IEEE80211_SCAN_ACTIVE ? "active" : "passive");
|
|
|
|
}
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
/*
|
|
|
|
* Start a scan unless one is already going.
|
|
|
|
*
|
|
|
|
* Called without the comlock held; grab the comlock as appropriate.
|
|
|
|
*/
|
2015-06-08 02:35:43 +00:00
|
|
|
static int
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
ieee80211_swscan_start_scan(const struct ieee80211_scanner *scan,
|
|
|
|
struct ieee80211vap *vap, int flags,
|
|
|
|
u_int duration, u_int mindwell, u_int maxdwell,
|
|
|
|
u_int nssid, const struct ieee80211_scan_ssid ssids[])
|
|
|
|
{
|
|
|
|
struct ieee80211com *ic = vap->iv_ic;
|
|
|
|
int result;
|
|
|
|
|
|
|
|
IEEE80211_UNLOCK_ASSERT(ic);
|
|
|
|
|
|
|
|
IEEE80211_LOCK(ic);
|
2015-05-10 06:59:34 +00:00
|
|
|
result = ieee80211_swscan_start_scan_locked(scan, vap, flags, duration,
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
mindwell, maxdwell, nssid, ssids);
|
|
|
|
IEEE80211_UNLOCK(ic);
|
|
|
|
|
|
|
|
return result;
|
|
|
|
}
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Check the scan cache for an ap/channel to use; if that
|
|
|
|
* fails then kick off a new scan.
|
|
|
|
*
|
|
|
|
* Called with the comlock held.
|
|
|
|
*
|
|
|
|
* XXX TODO: split out!
|
|
|
|
*/
|
2015-06-08 02:35:43 +00:00
|
|
|
static int
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
ieee80211_swscan_check_scan(const struct ieee80211_scanner *scan,
|
|
|
|
struct ieee80211vap *vap, int flags,
|
|
|
|
u_int duration, u_int mindwell, u_int maxdwell,
|
|
|
|
u_int nssid, const struct ieee80211_scan_ssid ssids[])
|
|
|
|
{
|
|
|
|
struct ieee80211com *ic = vap->iv_ic;
|
|
|
|
struct ieee80211_scan_state *ss = ic->ic_scan;
|
|
|
|
int result;
|
|
|
|
|
|
|
|
IEEE80211_LOCK_ASSERT(ic);
|
|
|
|
|
|
|
|
if (ss->ss_ops != NULL) {
|
|
|
|
/* XXX verify ss_ops matches vap->iv_opmode */
|
|
|
|
if ((flags & IEEE80211_SCAN_NOSSID) == 0) {
|
|
|
|
/*
|
|
|
|
* Update the ssid list and mark flags so if
|
|
|
|
* we call start_scan it doesn't duplicate work.
|
|
|
|
*/
|
|
|
|
ieee80211_scan_copy_ssid(vap, ss, nssid, ssids);
|
|
|
|
flags |= IEEE80211_SCAN_NOSSID;
|
|
|
|
}
|
|
|
|
if ((ic->ic_flags & IEEE80211_F_SCAN) == 0 &&
|
|
|
|
(flags & IEEE80211_SCAN_FLUSH) == 0 &&
|
2016-03-30 00:44:10 +00:00
|
|
|
ieee80211_time_before(ticks, ic->ic_lastscan + vap->iv_scanvalid)) {
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
/*
|
|
|
|
* We're not currently scanning and the cache is
|
|
|
|
* deemed hot enough to consult. Lock out others
|
|
|
|
* by marking IEEE80211_F_SCAN while we decide if
|
|
|
|
* something is already in the scan cache we can
|
|
|
|
* use. Also discard any frames that might come
|
|
|
|
* in while temporarily marked as scanning.
|
|
|
|
*/
|
2020-06-05 00:16:54 +00:00
|
|
|
IEEE80211_DPRINTF(vap, IEEE80211_MSG_SCAN,
|
|
|
|
"cache hot; ic_lastscan=%d, scanvalid=%d, ticks=%d\n",
|
|
|
|
ic->ic_lastscan,
|
|
|
|
vap->iv_scanvalid,
|
|
|
|
ticks);
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
SCAN_PRIVATE(ss)->ss_iflags |= ISCAN_DISCARD;
|
|
|
|
ic->ic_flags |= IEEE80211_F_SCAN;
|
|
|
|
|
|
|
|
/* NB: need to use supplied flags in check */
|
2023-03-14 21:00:48 +00:00
|
|
|
ss->ss_flags = flags & IEEE80211_SCAN_PUBLIC_MASK;
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
result = ss->ss_ops->scan_end(ss, vap);
|
|
|
|
|
|
|
|
ic->ic_flags &= ~IEEE80211_F_SCAN;
|
|
|
|
SCAN_PRIVATE(ss)->ss_iflags &= ~ISCAN_DISCARD;
|
2020-06-05 00:16:54 +00:00
|
|
|
IEEE80211_DPRINTF(vap, IEEE80211_MSG_SCAN,
|
|
|
|
"%s: scan_end returned %d\n", __func__, result);
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
if (result) {
|
|
|
|
ieee80211_notify_scan_done(vap);
|
|
|
|
return 1;
|
|
|
|
}
|
|
|
|
}
|
|
|
|
}
|
2015-05-10 06:59:34 +00:00
|
|
|
result = ieee80211_swscan_start_scan_locked(scan, vap, flags, duration,
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
mindwell, maxdwell, nssid, ssids);
|
|
|
|
|
|
|
|
return result;
|
|
|
|
}
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Restart a previous scan. If the previous scan completed
|
|
|
|
* then we start again using the existing channel list.
|
|
|
|
*/
|
2015-06-08 02:35:43 +00:00
|
|
|
static int
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
ieee80211_swscan_bg_scan(const struct ieee80211_scanner *scan,
|
|
|
|
struct ieee80211vap *vap, int flags)
|
|
|
|
{
|
|
|
|
struct ieee80211com *ic = vap->iv_ic;
|
|
|
|
struct ieee80211_scan_state *ss = ic->ic_scan;
|
2023-02-18 01:15:21 +00:00
|
|
|
bool scanning;
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
|
|
|
|
/* XXX assert unlocked? */
|
|
|
|
// IEEE80211_UNLOCK_ASSERT(ic);
|
|
|
|
|
|
|
|
IEEE80211_LOCK(ic);
|
2023-02-18 01:15:21 +00:00
|
|
|
scanning = ic->ic_flags & IEEE80211_F_SCAN;
|
|
|
|
if (!scanning) {
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
u_int duration;
|
|
|
|
/*
|
|
|
|
* Go off-channel for a fixed interval that is large
|
|
|
|
* enough to catch most ap's but short enough that
|
|
|
|
* we can return on-channel before our listen interval
|
|
|
|
* expires.
|
|
|
|
*/
|
|
|
|
duration = IEEE80211_SCAN_OFFCHANNEL;
|
|
|
|
|
|
|
|
IEEE80211_DPRINTF(vap, IEEE80211_MSG_SCAN,
|
2016-01-04 17:17:06 +00:00
|
|
|
"%s: %s scan, ticks %u duration %u\n", __func__,
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
ss->ss_flags & IEEE80211_SCAN_ACTIVE ? "active" : "passive",
|
|
|
|
ticks, duration);
|
|
|
|
|
|
|
|
ieee80211_scan_update_locked(vap, scan);
|
|
|
|
if (ss->ss_ops != NULL) {
|
|
|
|
ss->ss_vap = vap;
|
|
|
|
/*
|
|
|
|
* A background scan does not select a new sta; it
|
|
|
|
* just refreshes the scan cache. Also, indicate
|
|
|
|
* the scan logic should follow the beacon schedule:
|
|
|
|
* we go off-channel and scan for a while, then
|
|
|
|
* return to the bss channel to receive a beacon,
|
|
|
|
* then go off-channel again. All during this time
|
|
|
|
* we notify the ap we're in power save mode. When
|
|
|
|
* the scan is complete we leave power save mode.
|
|
|
|
* If any beacon indicates there are frames pending
|
|
|
|
* for us then we drop out of power save mode
|
|
|
|
* (and background scan) automatically by way of the
|
|
|
|
* usual sta power save logic.
|
|
|
|
*/
|
|
|
|
ss->ss_flags |= IEEE80211_SCAN_NOPICK
|
|
|
|
| IEEE80211_SCAN_BGSCAN
|
|
|
|
| flags
|
|
|
|
;
|
|
|
|
/* if previous scan completed, restart */
|
|
|
|
if (ss->ss_next >= ss->ss_last) {
|
|
|
|
if (ss->ss_flags & IEEE80211_SCAN_ACTIVE)
|
|
|
|
vap->iv_stats.is_scan_active++;
|
|
|
|
else
|
|
|
|
vap->iv_stats.is_scan_passive++;
|
|
|
|
/*
|
|
|
|
* NB: beware of the scan cache being flushed;
|
|
|
|
* if the channel list is empty use the
|
|
|
|
* scan_start method to populate it.
|
|
|
|
*/
|
|
|
|
ss->ss_next = 0;
|
|
|
|
if (ss->ss_last != 0)
|
|
|
|
ss->ss_ops->scan_restart(ss, vap);
|
|
|
|
else {
|
|
|
|
ss->ss_ops->scan_start(ss, vap);
|
|
|
|
#ifdef IEEE80211_DEBUG
|
|
|
|
if (ieee80211_msg_scan(vap))
|
|
|
|
ieee80211_scan_dump(ss);
|
|
|
|
#endif /* IEEE80211_DEBUG */
|
|
|
|
}
|
|
|
|
}
|
|
|
|
ieee80211_swscan_set_scan_duration(vap, duration);
|
|
|
|
ss->ss_maxdwell = duration;
|
|
|
|
ic->ic_flags |= IEEE80211_F_SCAN;
|
|
|
|
ic->ic_flags_ext |= IEEE80211_FEXT_BGSCAN;
|
2016-02-29 20:53:27 +00:00
|
|
|
ieee80211_runtask(ic,
|
|
|
|
&SCAN_PRIVATE(ss)->ss_scan_start);
|
2023-02-18 01:15:21 +00:00
|
|
|
scanning = true;
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
} else {
|
|
|
|
/* XXX msg+stat */
|
|
|
|
}
|
|
|
|
} else {
|
|
|
|
IEEE80211_DPRINTF(vap, IEEE80211_MSG_SCAN,
|
|
|
|
"%s: %s scan already in progress\n", __func__,
|
|
|
|
ss->ss_flags & IEEE80211_SCAN_ACTIVE ? "active" : "passive");
|
|
|
|
}
|
|
|
|
IEEE80211_UNLOCK(ic);
|
|
|
|
|
2023-02-18 01:15:21 +00:00
|
|
|
return (scanning);
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
}
|
|
|
|
|
2016-10-19 05:03:46 +00:00
|
|
|
/*
|
|
|
|
* Taskqueue work to cancel a scan.
|
|
|
|
*
|
|
|
|
* Note: for offload scan devices, we may want to call into the
|
|
|
|
* driver to try and cancel scanning, however it may not be cancelable.
|
|
|
|
*/
|
2015-06-08 02:35:43 +00:00
|
|
|
static void
|
2016-02-29 20:36:00 +00:00
|
|
|
cancel_scan(struct ieee80211vap *vap, int any, const char *func)
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
{
|
|
|
|
struct ieee80211com *ic = vap->iv_ic;
|
|
|
|
struct ieee80211_scan_state *ss = ic->ic_scan;
|
2016-09-30 18:43:39 +00:00
|
|
|
struct scan_state *ss_priv = SCAN_PRIVATE(ss);
|
|
|
|
int signal;
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
|
|
|
|
IEEE80211_LOCK(ic);
|
2016-09-30 18:43:39 +00:00
|
|
|
signal = any ? ISCAN_PAUSE : ISCAN_CANCEL;
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
if ((ic->ic_flags & IEEE80211_F_SCAN) &&
|
2016-02-29 20:36:00 +00:00
|
|
|
(any || ss->ss_vap == vap) &&
|
2016-09-30 18:43:39 +00:00
|
|
|
(ss_priv->ss_iflags & signal) == 0) {
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
IEEE80211_DPRINTF(vap, IEEE80211_MSG_SCAN,
|
2016-09-30 18:43:39 +00:00
|
|
|
"%s: %s %s scan\n", func,
|
|
|
|
any ? "pause" : "cancel",
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
ss->ss_flags & IEEE80211_SCAN_ACTIVE ?
|
|
|
|
"active" : "passive");
|
|
|
|
|
2016-02-29 21:00:10 +00:00
|
|
|
/* clear bg scan NOPICK */
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
ss->ss_flags &= ~IEEE80211_SCAN_NOPICK;
|
2016-09-30 18:43:39 +00:00
|
|
|
/* mark request and wake up the scan task */
|
|
|
|
scan_signal_locked(ss, signal);
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
} else {
|
|
|
|
IEEE80211_DPRINTF(vap, IEEE80211_MSG_SCAN,
|
2016-09-30 18:43:39 +00:00
|
|
|
"%s: called; F_SCAN=%d, vap=%s, signal=%d\n",
|
2016-02-29 20:36:00 +00:00
|
|
|
func,
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
!! (ic->ic_flags & IEEE80211_F_SCAN),
|
|
|
|
(ss->ss_vap == vap ? "match" : "nomatch"),
|
2016-09-30 18:43:39 +00:00
|
|
|
!! (ss_priv->ss_iflags & signal));
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
}
|
|
|
|
IEEE80211_UNLOCK(ic);
|
|
|
|
}
|
|
|
|
|
2016-02-29 20:36:00 +00:00
|
|
|
/*
|
|
|
|
* Cancel any scan currently going on for the specified vap.
|
|
|
|
*/
|
|
|
|
static void
|
|
|
|
ieee80211_swscan_cancel_scan(struct ieee80211vap *vap)
|
|
|
|
{
|
|
|
|
cancel_scan(vap, 0, __func__);
|
|
|
|
}
|
|
|
|
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
/*
|
|
|
|
* Cancel any scan currently going on.
|
|
|
|
*/
|
2015-06-08 02:35:43 +00:00
|
|
|
static void
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
ieee80211_swscan_cancel_anyscan(struct ieee80211vap *vap)
|
|
|
|
{
|
2016-10-28 02:09:45 +00:00
|
|
|
|
|
|
|
/* XXX for now - just don't do this per packet. */
|
|
|
|
if (vap->iv_flags_ext & IEEE80211_FEXT_SCAN_OFFLOAD)
|
|
|
|
return;
|
|
|
|
|
2016-02-29 20:36:00 +00:00
|
|
|
cancel_scan(vap, 1, __func__);
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
/*
|
2016-04-21 06:19:33 +00:00
|
|
|
* Manually switch to the next channel in the channel list.
|
|
|
|
* Provided for drivers that manage scanning themselves
|
|
|
|
* (e.g. for firmware-based devices).
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
*/
|
2015-06-08 02:35:43 +00:00
|
|
|
static void
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
ieee80211_swscan_scan_next(struct ieee80211vap *vap)
|
|
|
|
{
|
2016-02-29 21:00:10 +00:00
|
|
|
struct ieee80211_scan_state *ss = vap->iv_ic->ic_scan;
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
|
|
|
|
IEEE80211_DPRINTF(vap, IEEE80211_MSG_SCAN, "%s: called\n", __func__);
|
|
|
|
|
|
|
|
/* wake up the scan task */
|
2016-02-29 21:00:10 +00:00
|
|
|
scan_signal(ss, 0);
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
/*
|
2016-04-21 06:19:33 +00:00
|
|
|
* Manually stop a scan that is currently running.
|
|
|
|
* Provided for drivers that are not able to scan single channels
|
|
|
|
* (e.g. for firmware-based devices).
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
*/
|
2015-06-08 02:35:43 +00:00
|
|
|
static void
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
ieee80211_swscan_scan_done(struct ieee80211vap *vap)
|
|
|
|
{
|
|
|
|
struct ieee80211com *ic = vap->iv_ic;
|
2016-02-29 21:03:54 +00:00
|
|
|
struct ieee80211_scan_state *ss = ic->ic_scan;
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
|
|
|
|
IEEE80211_LOCK_ASSERT(ic);
|
|
|
|
|
2016-02-29 21:00:10 +00:00
|
|
|
scan_signal_locked(ss, 0);
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
/*
|
2016-04-21 06:19:33 +00:00
|
|
|
* Probe the current channel, if allowed, while scanning.
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
* If the channel is not marked passive-only then send
|
|
|
|
* a probe request immediately. Otherwise mark state and
|
|
|
|
* listen for beacons on the channel; if we receive something
|
|
|
|
* then we'll transmit a probe request.
|
|
|
|
*/
|
2015-06-08 02:35:43 +00:00
|
|
|
static void
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
ieee80211_swscan_probe_curchan(struct ieee80211vap *vap, int force)
|
|
|
|
{
|
|
|
|
struct ieee80211com *ic = vap->iv_ic;
|
|
|
|
struct ieee80211_scan_state *ss = ic->ic_scan;
|
|
|
|
struct ifnet *ifp = vap->iv_ifp;
|
|
|
|
int i;
|
|
|
|
|
2016-10-19 05:03:46 +00:00
|
|
|
/*
|
|
|
|
* Full-offload scan devices don't require this.
|
|
|
|
*/
|
|
|
|
if (vap->iv_flags_ext & IEEE80211_FEXT_SCAN_OFFLOAD)
|
|
|
|
return;
|
|
|
|
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
/*
|
|
|
|
* Send directed probe requests followed by any
|
|
|
|
* broadcast probe request.
|
|
|
|
* XXX remove dependence on ic/vap->iv_bss
|
|
|
|
*/
|
|
|
|
for (i = 0; i < ss->ss_nssid; i++)
|
|
|
|
ieee80211_send_probereq(vap->iv_bss,
|
|
|
|
vap->iv_myaddr, ifp->if_broadcastaddr,
|
|
|
|
ifp->if_broadcastaddr,
|
|
|
|
ss->ss_ssid[i].ssid, ss->ss_ssid[i].len);
|
|
|
|
if ((ss->ss_flags & IEEE80211_SCAN_NOBCAST) == 0)
|
|
|
|
ieee80211_send_probereq(vap->iv_bss,
|
|
|
|
vap->iv_myaddr, ifp->if_broadcastaddr,
|
|
|
|
ifp->if_broadcastaddr,
|
|
|
|
"", 0);
|
|
|
|
}
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Scan curchan. If this is an active scan and the channel
|
|
|
|
* is not marked passive then send probe request frame(s).
|
|
|
|
* Arrange for the channel change after maxdwell ticks.
|
|
|
|
*/
|
|
|
|
static void
|
|
|
|
scan_curchan(struct ieee80211_scan_state *ss, unsigned long maxdwell)
|
|
|
|
{
|
|
|
|
struct ieee80211vap *vap = ss->ss_vap;
|
2016-02-29 21:03:54 +00:00
|
|
|
struct ieee80211com *ic = ss->ss_ic;
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
|
|
|
|
IEEE80211_DPRINTF(vap, IEEE80211_MSG_SCAN,
|
|
|
|
"%s: calling; maxdwell=%lu\n",
|
|
|
|
__func__,
|
|
|
|
maxdwell);
|
2016-02-29 21:03:54 +00:00
|
|
|
IEEE80211_LOCK(ic);
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
if (ss->ss_flags & IEEE80211_SCAN_ACTIVE)
|
|
|
|
ieee80211_probe_curchan(vap, 0);
|
2016-02-29 21:03:54 +00:00
|
|
|
taskqueue_enqueue_timeout(ic->ic_tq,
|
2016-02-29 20:53:27 +00:00
|
|
|
&SCAN_PRIVATE(ss)->ss_scan_curchan, maxdwell);
|
2016-02-29 21:03:54 +00:00
|
|
|
IEEE80211_UNLOCK(ic);
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
static void
|
2016-02-29 21:00:10 +00:00
|
|
|
scan_signal(struct ieee80211_scan_state *ss, int iflags)
|
|
|
|
{
|
|
|
|
struct ieee80211com *ic = ss->ss_ic;
|
|
|
|
|
|
|
|
IEEE80211_UNLOCK_ASSERT(ic);
|
|
|
|
|
|
|
|
IEEE80211_LOCK(ic);
|
|
|
|
scan_signal_locked(ss, iflags);
|
|
|
|
IEEE80211_UNLOCK(ic);
|
|
|
|
}
|
|
|
|
|
|
|
|
static void
|
|
|
|
scan_signal_locked(struct ieee80211_scan_state *ss, int iflags)
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
{
|
2016-02-29 20:53:27 +00:00
|
|
|
struct scan_state *ss_priv = SCAN_PRIVATE(ss);
|
|
|
|
struct timeout_task *scan_task = &ss_priv->ss_scan_curchan;
|
|
|
|
struct ieee80211com *ic = ss->ss_ic;
|
|
|
|
|
|
|
|
IEEE80211_LOCK_ASSERT(ic);
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
|
2016-02-29 21:00:10 +00:00
|
|
|
ss_priv->ss_iflags |= iflags;
|
2016-02-29 20:53:27 +00:00
|
|
|
if (ss_priv->ss_iflags & ISCAN_RUNNING) {
|
|
|
|
if (taskqueue_cancel_timeout(ic->ic_tq, scan_task, NULL) == 0)
|
|
|
|
taskqueue_enqueue_timeout(ic->ic_tq, scan_task, 0);
|
|
|
|
}
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Handle mindwell requirements completed; initiate a channel
|
|
|
|
* change to the next channel asap.
|
|
|
|
*/
|
|
|
|
static void
|
|
|
|
scan_mindwell(struct ieee80211_scan_state *ss)
|
|
|
|
{
|
|
|
|
|
2016-02-29 23:09:31 +00:00
|
|
|
IEEE80211_DPRINTF(ss->ss_vap, IEEE80211_MSG_SCAN, "%s: called\n",
|
|
|
|
__func__);
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
|
2016-02-29 21:00:10 +00:00
|
|
|
scan_signal(ss, 0);
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
static void
|
2016-02-29 20:53:27 +00:00
|
|
|
scan_start(void *arg, int pending)
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
{
|
|
|
|
#define ISCAN_REP (ISCAN_MINDWELL | ISCAN_DISCARD)
|
|
|
|
struct ieee80211_scan_state *ss = (struct ieee80211_scan_state *) arg;
|
2016-02-29 20:39:04 +00:00
|
|
|
struct scan_state *ss_priv = SCAN_PRIVATE(ss);
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
struct ieee80211vap *vap = ss->ss_vap;
|
|
|
|
struct ieee80211com *ic = ss->ss_ic;
|
|
|
|
|
|
|
|
IEEE80211_LOCK(ic);
|
|
|
|
if (vap == NULL || (ic->ic_flags & IEEE80211_F_SCAN) == 0 ||
|
2016-02-29 20:39:04 +00:00
|
|
|
(ss_priv->ss_iflags & ISCAN_ABORT)) {
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
/* Cancelled before we started */
|
2016-02-29 20:44:59 +00:00
|
|
|
scan_done(ss, 0);
|
|
|
|
return;
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
if (ss->ss_next == ss->ss_last) {
|
|
|
|
IEEE80211_DPRINTF(vap, IEEE80211_MSG_SCAN,
|
|
|
|
"%s: no channels to scan\n", __func__);
|
2016-02-29 20:44:59 +00:00
|
|
|
scan_done(ss, 1);
|
|
|
|
return;
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
}
|
|
|
|
|
2016-10-19 05:03:46 +00:00
|
|
|
/*
|
|
|
|
* Put the station into power save mode.
|
|
|
|
*
|
|
|
|
* This is only required if we're not a full-offload devices;
|
|
|
|
* those devices manage scan/traffic differently.
|
|
|
|
*/
|
|
|
|
if (((vap->iv_flags_ext & IEEE80211_FEXT_SCAN_OFFLOAD) == 0) &&
|
|
|
|
vap->iv_opmode == IEEE80211_M_STA &&
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
vap->iv_state == IEEE80211_S_RUN) {
|
|
|
|
if ((vap->iv_bss->ni_flags & IEEE80211_NODE_PWR_MGT) == 0) {
|
|
|
|
/* Enable station power save mode */
|
|
|
|
vap->iv_sta_ps(vap, 1);
|
2016-02-29 20:56:02 +00:00
|
|
|
/* Wait until null data frame will be ACK'ed */
|
2016-02-29 20:53:27 +00:00
|
|
|
mtx_sleep(vap, IEEE80211_LOCK_OBJ(ic), PCATCH,
|
2016-02-29 20:56:02 +00:00
|
|
|
"sta_ps", msecs_to_ticks(10));
|
2016-02-29 20:44:59 +00:00
|
|
|
if (ss_priv->ss_iflags & ISCAN_ABORT) {
|
|
|
|
scan_done(ss, 0);
|
|
|
|
return;
|
|
|
|
}
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
}
|
|
|
|
}
|
|
|
|
|
2016-02-29 20:41:10 +00:00
|
|
|
ss_priv->ss_scanend = ticks + ss_priv->ss_duration;
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
|
|
|
|
/* XXX scan state can change! Re-validate scan state! */
|
|
|
|
|
|
|
|
IEEE80211_UNLOCK(ic);
|
2016-02-29 20:53:27 +00:00
|
|
|
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
ic->ic_scan_start(ic); /* notify driver */
|
|
|
|
|
2016-02-29 20:53:27 +00:00
|
|
|
scan_curchan_task(ss, 0);
|
|
|
|
}
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
|
2016-02-29 20:53:27 +00:00
|
|
|
static void
|
|
|
|
scan_curchan_task(void *arg, int pending)
|
|
|
|
{
|
|
|
|
struct ieee80211_scan_state *ss = arg;
|
|
|
|
struct scan_state *ss_priv = SCAN_PRIVATE(ss);
|
|
|
|
struct ieee80211com *ic = ss->ss_ic;
|
|
|
|
struct ieee80211_channel *chan;
|
|
|
|
unsigned long maxdwell;
|
[net80211] Fix interrupted scan logic and ticks comparison
The scan task refactoring stuff circa 2014-2016 broke the blocking task
into a taskqueue with some async bits, but it apparently broke scans
being interrupted by traffic.
Notably - the new "field" SCAN_PAUSE sets both SCAN_INTERRUPT and SCAN_CANCEL,
and a bunch of existing code was checking for SCAN_CANCEL only and breaking
the scan. Unfortunately it was then (a) cancelling the scan entirely and
(b) not notifying userland that scan was done.
So:
* Update the calls to scan_end() to only pass in 1 (saying the scan is complete)
if SCAN_CANCEL is set WITHOUT SCAN_INTERRUPT. If both are set then yes,
the scan is interrupted, but it isn't canceled - it's just paused.
* Update the "did the scan flags change whilst the driver was called" logic
to check for canceled scans, not interrupted scans.
* The "scan done" logic now explicitly checks for either interrupted or
completed scans. This accounts for the situation where a scan is being
aborted via traffic but it ALSO happens to have finished (ie the last
channel was checked.)
This doesn't ENTIRELY fix scanning as the resume function is broken
due to incorrect ticks math. Thus, the second half of this patch
changes the ieee80211_ticks_*() macros to use int instead of long,
matching the logic that the TCP code does with ticks and handles
wrapping / negative ticks values. If cast to long then the wrapping
math wouldn't work right (ie, if ticks was actually negative,
ie, after the system has been up for a while.)
This allows contbgscan() to correctly calculate if a scan should
continue based on ticks and ic->ic_lastdata .
Reviewed by: bz
Differential Revision: https://reviews.freebsd.org/D25031
2020-05-27 18:32:12 +00:00
|
|
|
int scandone, scanstop;
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
|
2016-02-29 20:53:27 +00:00
|
|
|
IEEE80211_LOCK(ic);
|
|
|
|
end:
|
[net80211] Fix interrupted scan logic and ticks comparison
The scan task refactoring stuff circa 2014-2016 broke the blocking task
into a taskqueue with some async bits, but it apparently broke scans
being interrupted by traffic.
Notably - the new "field" SCAN_PAUSE sets both SCAN_INTERRUPT and SCAN_CANCEL,
and a bunch of existing code was checking for SCAN_CANCEL only and breaking
the scan. Unfortunately it was then (a) cancelling the scan entirely and
(b) not notifying userland that scan was done.
So:
* Update the calls to scan_end() to only pass in 1 (saying the scan is complete)
if SCAN_CANCEL is set WITHOUT SCAN_INTERRUPT. If both are set then yes,
the scan is interrupted, but it isn't canceled - it's just paused.
* Update the "did the scan flags change whilst the driver was called" logic
to check for canceled scans, not interrupted scans.
* The "scan done" logic now explicitly checks for either interrupted or
completed scans. This accounts for the situation where a scan is being
aborted via traffic but it ALSO happens to have finished (ie the last
channel was checked.)
This doesn't ENTIRELY fix scanning as the resume function is broken
due to incorrect ticks math. Thus, the second half of this patch
changes the ieee80211_ticks_*() macros to use int instead of long,
matching the logic that the TCP code does with ticks and handles
wrapping / negative ticks values. If cast to long then the wrapping
math wouldn't work right (ie, if ticks was actually negative,
ie, after the system has been up for a while.)
This allows contbgscan() to correctly calculate if a scan should
continue based on ticks and ic->ic_lastdata .
Reviewed by: bz
Differential Revision: https://reviews.freebsd.org/D25031
2020-05-27 18:32:12 +00:00
|
|
|
/*
|
|
|
|
* Note: only /end/ the scan if we're CANCEL rather than
|
|
|
|
* CANCEL+INTERRUPT (ie, 'PAUSE').
|
|
|
|
*
|
|
|
|
* We can stop the scan if we hit cancel, but we shouldn't
|
|
|
|
* call scan_end(ss, 1) if we're just PAUSEing the scan.
|
|
|
|
*/
|
2016-02-29 20:53:27 +00:00
|
|
|
scandone = (ss->ss_next >= ss->ss_last) ||
|
[net80211] Fix interrupted scan logic and ticks comparison
The scan task refactoring stuff circa 2014-2016 broke the blocking task
into a taskqueue with some async bits, but it apparently broke scans
being interrupted by traffic.
Notably - the new "field" SCAN_PAUSE sets both SCAN_INTERRUPT and SCAN_CANCEL,
and a bunch of existing code was checking for SCAN_CANCEL only and breaking
the scan. Unfortunately it was then (a) cancelling the scan entirely and
(b) not notifying userland that scan was done.
So:
* Update the calls to scan_end() to only pass in 1 (saying the scan is complete)
if SCAN_CANCEL is set WITHOUT SCAN_INTERRUPT. If both are set then yes,
the scan is interrupted, but it isn't canceled - it's just paused.
* Update the "did the scan flags change whilst the driver was called" logic
to check for canceled scans, not interrupted scans.
* The "scan done" logic now explicitly checks for either interrupted or
completed scans. This accounts for the situation where a scan is being
aborted via traffic but it ALSO happens to have finished (ie the last
channel was checked.)
This doesn't ENTIRELY fix scanning as the resume function is broken
due to incorrect ticks math. Thus, the second half of this patch
changes the ieee80211_ticks_*() macros to use int instead of long,
matching the logic that the TCP code does with ticks and handles
wrapping / negative ticks values. If cast to long then the wrapping
math wouldn't work right (ie, if ticks was actually negative,
ie, after the system has been up for a while.)
This allows contbgscan() to correctly calculate if a scan should
continue based on ticks and ic->ic_lastdata .
Reviewed by: bz
Differential Revision: https://reviews.freebsd.org/D25031
2020-05-27 18:32:12 +00:00
|
|
|
((ss_priv->ss_iflags & ISCAN_PAUSE) == ISCAN_CANCEL);
|
|
|
|
scanstop = (ss->ss_next >= ss->ss_last) ||
|
|
|
|
((ss_priv->ss_iflags & ISCAN_CANCEL) != 0);
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
|
2016-02-29 23:09:31 +00:00
|
|
|
IEEE80211_DPRINTF(ss->ss_vap, IEEE80211_MSG_SCAN,
|
[net80211] Fix interrupted scan logic and ticks comparison
The scan task refactoring stuff circa 2014-2016 broke the blocking task
into a taskqueue with some async bits, but it apparently broke scans
being interrupted by traffic.
Notably - the new "field" SCAN_PAUSE sets both SCAN_INTERRUPT and SCAN_CANCEL,
and a bunch of existing code was checking for SCAN_CANCEL only and breaking
the scan. Unfortunately it was then (a) cancelling the scan entirely and
(b) not notifying userland that scan was done.
So:
* Update the calls to scan_end() to only pass in 1 (saying the scan is complete)
if SCAN_CANCEL is set WITHOUT SCAN_INTERRUPT. If both are set then yes,
the scan is interrupted, but it isn't canceled - it's just paused.
* Update the "did the scan flags change whilst the driver was called" logic
to check for canceled scans, not interrupted scans.
* The "scan done" logic now explicitly checks for either interrupted or
completed scans. This accounts for the situation where a scan is being
aborted via traffic but it ALSO happens to have finished (ie the last
channel was checked.)
This doesn't ENTIRELY fix scanning as the resume function is broken
due to incorrect ticks math. Thus, the second half of this patch
changes the ieee80211_ticks_*() macros to use int instead of long,
matching the logic that the TCP code does with ticks and handles
wrapping / negative ticks values. If cast to long then the wrapping
math wouldn't work right (ie, if ticks was actually negative,
ie, after the system has been up for a while.)
This allows contbgscan() to correctly calculate if a scan should
continue based on ticks and ic->ic_lastdata .
Reviewed by: bz
Differential Revision: https://reviews.freebsd.org/D25031
2020-05-27 18:32:12 +00:00
|
|
|
"%s: loop start; scandone=%d, scanstop=%d, ss_iflags=0x%x, ss_next=%u, ss_last=%u\n",
|
2016-02-29 20:53:27 +00:00
|
|
|
__func__,
|
[net80211] Fix interrupted scan logic and ticks comparison
The scan task refactoring stuff circa 2014-2016 broke the blocking task
into a taskqueue with some async bits, but it apparently broke scans
being interrupted by traffic.
Notably - the new "field" SCAN_PAUSE sets both SCAN_INTERRUPT and SCAN_CANCEL,
and a bunch of existing code was checking for SCAN_CANCEL only and breaking
the scan. Unfortunately it was then (a) cancelling the scan entirely and
(b) not notifying userland that scan was done.
So:
* Update the calls to scan_end() to only pass in 1 (saying the scan is complete)
if SCAN_CANCEL is set WITHOUT SCAN_INTERRUPT. If both are set then yes,
the scan is interrupted, but it isn't canceled - it's just paused.
* Update the "did the scan flags change whilst the driver was called" logic
to check for canceled scans, not interrupted scans.
* The "scan done" logic now explicitly checks for either interrupted or
completed scans. This accounts for the situation where a scan is being
aborted via traffic but it ALSO happens to have finished (ie the last
channel was checked.)
This doesn't ENTIRELY fix scanning as the resume function is broken
due to incorrect ticks math. Thus, the second half of this patch
changes the ieee80211_ticks_*() macros to use int instead of long,
matching the logic that the TCP code does with ticks and handles
wrapping / negative ticks values. If cast to long then the wrapping
math wouldn't work right (ie, if ticks was actually negative,
ie, after the system has been up for a while.)
This allows contbgscan() to correctly calculate if a scan should
continue based on ticks and ic->ic_lastdata .
Reviewed by: bz
Differential Revision: https://reviews.freebsd.org/D25031
2020-05-27 18:32:12 +00:00
|
|
|
scandone,
|
|
|
|
scanstop,
|
|
|
|
(uint32_t) ss_priv->ss_iflags,
|
|
|
|
(uint32_t) ss->ss_next,
|
|
|
|
(uint32_t) ss->ss_last);
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
|
[net80211] Fix interrupted scan logic and ticks comparison
The scan task refactoring stuff circa 2014-2016 broke the blocking task
into a taskqueue with some async bits, but it apparently broke scans
being interrupted by traffic.
Notably - the new "field" SCAN_PAUSE sets both SCAN_INTERRUPT and SCAN_CANCEL,
and a bunch of existing code was checking for SCAN_CANCEL only and breaking
the scan. Unfortunately it was then (a) cancelling the scan entirely and
(b) not notifying userland that scan was done.
So:
* Update the calls to scan_end() to only pass in 1 (saying the scan is complete)
if SCAN_CANCEL is set WITHOUT SCAN_INTERRUPT. If both are set then yes,
the scan is interrupted, but it isn't canceled - it's just paused.
* Update the "did the scan flags change whilst the driver was called" logic
to check for canceled scans, not interrupted scans.
* The "scan done" logic now explicitly checks for either interrupted or
completed scans. This accounts for the situation where a scan is being
aborted via traffic but it ALSO happens to have finished (ie the last
channel was checked.)
This doesn't ENTIRELY fix scanning as the resume function is broken
due to incorrect ticks math. Thus, the second half of this patch
changes the ieee80211_ticks_*() macros to use int instead of long,
matching the logic that the TCP code does with ticks and handles
wrapping / negative ticks values. If cast to long then the wrapping
math wouldn't work right (ie, if ticks was actually negative,
ie, after the system has been up for a while.)
This allows contbgscan() to correctly calculate if a scan should
continue based on ticks and ic->ic_lastdata .
Reviewed by: bz
Differential Revision: https://reviews.freebsd.org/D25031
2020-05-27 18:32:12 +00:00
|
|
|
if (scanstop || (ss->ss_flags & IEEE80211_SCAN_GOTPICK) ||
|
2016-02-29 20:53:27 +00:00
|
|
|
(ss_priv->ss_iflags & ISCAN_ABORT) ||
|
2016-03-30 00:44:10 +00:00
|
|
|
ieee80211_time_after(ticks + ss->ss_mindwell, ss_priv->ss_scanend)) {
|
2016-02-29 20:53:27 +00:00
|
|
|
ss_priv->ss_iflags &= ~ISCAN_RUNNING;
|
|
|
|
scan_end(ss, scandone);
|
|
|
|
return;
|
|
|
|
} else
|
|
|
|
ss_priv->ss_iflags |= ISCAN_RUNNING;
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
|
2016-02-29 20:53:27 +00:00
|
|
|
chan = ss->ss_chans[ss->ss_next++];
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
|
2016-02-29 20:53:27 +00:00
|
|
|
/*
|
|
|
|
* Watch for truncation due to the scan end time.
|
|
|
|
*/
|
2016-03-30 00:44:10 +00:00
|
|
|
if (ieee80211_time_after(ticks + ss->ss_maxdwell, ss_priv->ss_scanend))
|
2016-02-29 20:53:27 +00:00
|
|
|
maxdwell = ss_priv->ss_scanend - ticks;
|
|
|
|
else
|
|
|
|
maxdwell = ss->ss_maxdwell;
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
|
2016-02-29 23:09:31 +00:00
|
|
|
IEEE80211_DPRINTF(ss->ss_vap, IEEE80211_MSG_SCAN,
|
2016-02-29 20:53:27 +00:00
|
|
|
"%s: chan %3d%c -> %3d%c [%s, dwell min %lums max %lums]\n",
|
|
|
|
__func__,
|
|
|
|
ieee80211_chan2ieee(ic, ic->ic_curchan),
|
|
|
|
ieee80211_channel_type_char(ic->ic_curchan),
|
|
|
|
ieee80211_chan2ieee(ic, chan),
|
|
|
|
ieee80211_channel_type_char(chan),
|
|
|
|
(ss->ss_flags & IEEE80211_SCAN_ACTIVE) &&
|
|
|
|
(chan->ic_flags & IEEE80211_CHAN_PASSIVE) == 0 ?
|
|
|
|
"active" : "passive",
|
|
|
|
ticks_to_msecs(ss->ss_mindwell), ticks_to_msecs(maxdwell));
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
|
2016-02-29 20:53:27 +00:00
|
|
|
/*
|
|
|
|
* Potentially change channel and phy mode.
|
|
|
|
*/
|
|
|
|
ic->ic_curchan = chan;
|
|
|
|
ic->ic_rt = ieee80211_get_ratetable(chan);
|
|
|
|
IEEE80211_UNLOCK(ic);
|
|
|
|
/*
|
|
|
|
* Perform the channel change and scan unlocked so the driver
|
|
|
|
* may sleep. Once set_channel returns the hardware has
|
|
|
|
* completed the channel change.
|
|
|
|
*/
|
|
|
|
ic->ic_set_channel(ic);
|
|
|
|
ieee80211_radiotap_chan_change(ic);
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Scan curchan. Drivers for "intelligent hardware"
|
|
|
|
* override ic_scan_curchan to tell the device to do
|
|
|
|
* the work. Otherwise we manage the work ourselves;
|
|
|
|
* sending a probe request (as needed), and arming the
|
|
|
|
* timeout to switch channels after maxdwell ticks.
|
|
|
|
*
|
|
|
|
* scan_curchan should only pause for the time required to
|
|
|
|
* prepare/initiate the hardware for the scan (if at all).
|
|
|
|
*/
|
|
|
|
ic->ic_scan_curchan(ss, maxdwell);
|
|
|
|
IEEE80211_LOCK(ic);
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
|
2016-02-29 20:53:27 +00:00
|
|
|
/* XXX scan state can change! Re-validate scan state! */
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
|
2016-02-29 20:53:27 +00:00
|
|
|
ss_priv->ss_chanmindwell = ticks + ss->ss_mindwell;
|
|
|
|
/* clear mindwell lock and initial channel change flush */
|
|
|
|
ss_priv->ss_iflags &= ~ISCAN_REP;
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
|
2016-04-19 20:19:21 +00:00
|
|
|
if (ss_priv->ss_iflags & (ISCAN_CANCEL|ISCAN_ABORT)) {
|
|
|
|
taskqueue_cancel_timeout(ic->ic_tq, &ss_priv->ss_scan_curchan,
|
|
|
|
NULL);
|
2016-02-29 20:53:27 +00:00
|
|
|
goto end;
|
2016-04-19 20:19:21 +00:00
|
|
|
}
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
|
2016-02-29 23:09:31 +00:00
|
|
|
IEEE80211_DPRINTF(ss->ss_vap, IEEE80211_MSG_SCAN, "%s: waiting\n",
|
|
|
|
__func__);
|
2016-02-29 20:53:27 +00:00
|
|
|
IEEE80211_UNLOCK(ic);
|
2016-02-29 20:47:07 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
static void
|
|
|
|
scan_end(struct ieee80211_scan_state *ss, int scandone)
|
|
|
|
{
|
|
|
|
struct scan_state *ss_priv = SCAN_PRIVATE(ss);
|
|
|
|
struct ieee80211vap *vap = ss->ss_vap;
|
|
|
|
struct ieee80211com *ic = ss->ss_ic;
|
|
|
|
|
|
|
|
IEEE80211_LOCK_ASSERT(ic);
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
|
|
|
|
IEEE80211_DPRINTF(vap, IEEE80211_MSG_SCAN, "%s: out\n", __func__);
|
|
|
|
|
2016-02-29 20:44:59 +00:00
|
|
|
if (ss_priv->ss_iflags & ISCAN_ABORT) {
|
|
|
|
scan_done(ss, scandone);
|
|
|
|
return;
|
|
|
|
}
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
|
|
|
|
IEEE80211_UNLOCK(ic);
|
|
|
|
ic->ic_scan_end(ic); /* notify driver */
|
|
|
|
IEEE80211_LOCK(ic);
|
|
|
|
/* XXX scan state can change! Re-validate scan state! */
|
|
|
|
|
|
|
|
/*
|
2016-05-03 18:05:43 +00:00
|
|
|
* Since a cancellation may have occurred during one of the
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
* driver calls (whilst unlocked), update scandone.
|
|
|
|
*/
|
[net80211] Fix interrupted scan logic and ticks comparison
The scan task refactoring stuff circa 2014-2016 broke the blocking task
into a taskqueue with some async bits, but it apparently broke scans
being interrupted by traffic.
Notably - the new "field" SCAN_PAUSE sets both SCAN_INTERRUPT and SCAN_CANCEL,
and a bunch of existing code was checking for SCAN_CANCEL only and breaking
the scan. Unfortunately it was then (a) cancelling the scan entirely and
(b) not notifying userland that scan was done.
So:
* Update the calls to scan_end() to only pass in 1 (saying the scan is complete)
if SCAN_CANCEL is set WITHOUT SCAN_INTERRUPT. If both are set then yes,
the scan is interrupted, but it isn't canceled - it's just paused.
* Update the "did the scan flags change whilst the driver was called" logic
to check for canceled scans, not interrupted scans.
* The "scan done" logic now explicitly checks for either interrupted or
completed scans. This accounts for the situation where a scan is being
aborted via traffic but it ALSO happens to have finished (ie the last
channel was checked.)
This doesn't ENTIRELY fix scanning as the resume function is broken
due to incorrect ticks math. Thus, the second half of this patch
changes the ieee80211_ticks_*() macros to use int instead of long,
matching the logic that the TCP code does with ticks and handles
wrapping / negative ticks values. If cast to long then the wrapping
math wouldn't work right (ie, if ticks was actually negative,
ie, after the system has been up for a while.)
This allows contbgscan() to correctly calculate if a scan should
continue based on ticks and ic->ic_lastdata .
Reviewed by: bz
Differential Revision: https://reviews.freebsd.org/D25031
2020-05-27 18:32:12 +00:00
|
|
|
if ((scandone == 0) && ((ss_priv->ss_iflags & ISCAN_PAUSE) == ISCAN_CANCEL)) {
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
/* XXX printf? */
|
|
|
|
if_printf(vap->iv_ifp,
|
[net80211] Fix interrupted scan logic and ticks comparison
The scan task refactoring stuff circa 2014-2016 broke the blocking task
into a taskqueue with some async bits, but it apparently broke scans
being interrupted by traffic.
Notably - the new "field" SCAN_PAUSE sets both SCAN_INTERRUPT and SCAN_CANCEL,
and a bunch of existing code was checking for SCAN_CANCEL only and breaking
the scan. Unfortunately it was then (a) cancelling the scan entirely and
(b) not notifying userland that scan was done.
So:
* Update the calls to scan_end() to only pass in 1 (saying the scan is complete)
if SCAN_CANCEL is set WITHOUT SCAN_INTERRUPT. If both are set then yes,
the scan is interrupted, but it isn't canceled - it's just paused.
* Update the "did the scan flags change whilst the driver was called" logic
to check for canceled scans, not interrupted scans.
* The "scan done" logic now explicitly checks for either interrupted or
completed scans. This accounts for the situation where a scan is being
aborted via traffic but it ALSO happens to have finished (ie the last
channel was checked.)
This doesn't ENTIRELY fix scanning as the resume function is broken
due to incorrect ticks math. Thus, the second half of this patch
changes the ieee80211_ticks_*() macros to use int instead of long,
matching the logic that the TCP code does with ticks and handles
wrapping / negative ticks values. If cast to long then the wrapping
math wouldn't work right (ie, if ticks was actually negative,
ie, after the system has been up for a while.)
This allows contbgscan() to correctly calculate if a scan should
continue based on ticks and ic->ic_lastdata .
Reviewed by: bz
Differential Revision: https://reviews.freebsd.org/D25031
2020-05-27 18:32:12 +00:00
|
|
|
"%s: OOPS! scan cancelled during driver call (1) (ss_iflags=0x%x)!\n",
|
|
|
|
__func__,
|
|
|
|
ss_priv->ss_iflags);
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
scandone = 1;
|
|
|
|
}
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Record scan complete time. Note that we also do
|
|
|
|
* this when canceled so any background scan will
|
|
|
|
* not be restarted for a while.
|
|
|
|
*/
|
|
|
|
if (scandone)
|
|
|
|
ic->ic_lastscan = ticks;
|
|
|
|
/* return to the bss channel */
|
|
|
|
if (ic->ic_bsschan != IEEE80211_CHAN_ANYC &&
|
|
|
|
ic->ic_curchan != ic->ic_bsschan) {
|
|
|
|
ieee80211_setupcurchan(ic, ic->ic_bsschan);
|
|
|
|
IEEE80211_UNLOCK(ic);
|
|
|
|
ic->ic_set_channel(ic);
|
|
|
|
ieee80211_radiotap_chan_change(ic);
|
|
|
|
IEEE80211_LOCK(ic);
|
|
|
|
}
|
|
|
|
/* clear internal flags and any indication of a pick */
|
2016-02-29 20:39:04 +00:00
|
|
|
ss_priv->ss_iflags &= ~ISCAN_REP;
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
ss->ss_flags &= ~IEEE80211_SCAN_GOTPICK;
|
|
|
|
|
|
|
|
/*
|
|
|
|
* If not canceled and scan completed, do post-processing.
|
|
|
|
* If the callback function returns 0, then it wants to
|
|
|
|
* continue/restart scanning. Unfortunately we needed to
|
|
|
|
* notify the driver to end the scan above to avoid having
|
|
|
|
* rx frames alter the scan candidate list.
|
|
|
|
*/
|
2016-02-29 20:39:04 +00:00
|
|
|
if ((ss_priv->ss_iflags & ISCAN_CANCEL) == 0 &&
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
!ss->ss_ops->scan_end(ss, vap) &&
|
|
|
|
(ss->ss_flags & IEEE80211_SCAN_ONCE) == 0 &&
|
2016-03-30 00:44:10 +00:00
|
|
|
ieee80211_time_before(ticks + ss->ss_mindwell, ss_priv->ss_scanend)) {
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
IEEE80211_DPRINTF(vap, IEEE80211_MSG_SCAN,
|
|
|
|
"%s: done, restart "
|
|
|
|
"[ticks %u, dwell min %lu scanend %lu]\n",
|
|
|
|
__func__,
|
2016-02-29 20:41:10 +00:00
|
|
|
ticks, ss->ss_mindwell, ss_priv->ss_scanend);
|
2016-05-03 18:05:43 +00:00
|
|
|
ss->ss_next = 0; /* reset to beginning */
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
if (ss->ss_flags & IEEE80211_SCAN_ACTIVE)
|
|
|
|
vap->iv_stats.is_scan_active++;
|
|
|
|
else
|
|
|
|
vap->iv_stats.is_scan_passive++;
|
|
|
|
|
|
|
|
ss->ss_ops->scan_restart(ss, vap); /* XXX? */
|
2016-02-29 20:53:27 +00:00
|
|
|
ieee80211_runtask(ic, &ss_priv->ss_scan_start);
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
IEEE80211_UNLOCK(ic);
|
|
|
|
return;
|
|
|
|
}
|
|
|
|
|
|
|
|
/* past here, scandone is ``true'' if not in bg mode */
|
|
|
|
if ((ss->ss_flags & IEEE80211_SCAN_BGSCAN) == 0)
|
|
|
|
scandone = 1;
|
|
|
|
|
|
|
|
IEEE80211_DPRINTF(vap, IEEE80211_MSG_SCAN,
|
|
|
|
"%s: %s, [ticks %u, dwell min %lu scanend %lu]\n",
|
|
|
|
__func__, scandone ? "done" : "stopped",
|
2016-02-29 20:41:10 +00:00
|
|
|
ticks, ss->ss_mindwell, ss_priv->ss_scanend);
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
|
|
|
|
/*
|
2016-05-03 18:05:43 +00:00
|
|
|
* Since a cancellation may have occurred during one of the
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
* driver calls (whilst unlocked), update scandone.
|
|
|
|
*/
|
[net80211] Fix interrupted scan logic and ticks comparison
The scan task refactoring stuff circa 2014-2016 broke the blocking task
into a taskqueue with some async bits, but it apparently broke scans
being interrupted by traffic.
Notably - the new "field" SCAN_PAUSE sets both SCAN_INTERRUPT and SCAN_CANCEL,
and a bunch of existing code was checking for SCAN_CANCEL only and breaking
the scan. Unfortunately it was then (a) cancelling the scan entirely and
(b) not notifying userland that scan was done.
So:
* Update the calls to scan_end() to only pass in 1 (saying the scan is complete)
if SCAN_CANCEL is set WITHOUT SCAN_INTERRUPT. If both are set then yes,
the scan is interrupted, but it isn't canceled - it's just paused.
* Update the "did the scan flags change whilst the driver was called" logic
to check for canceled scans, not interrupted scans.
* The "scan done" logic now explicitly checks for either interrupted or
completed scans. This accounts for the situation where a scan is being
aborted via traffic but it ALSO happens to have finished (ie the last
channel was checked.)
This doesn't ENTIRELY fix scanning as the resume function is broken
due to incorrect ticks math. Thus, the second half of this patch
changes the ieee80211_ticks_*() macros to use int instead of long,
matching the logic that the TCP code does with ticks and handles
wrapping / negative ticks values. If cast to long then the wrapping
math wouldn't work right (ie, if ticks was actually negative,
ie, after the system has been up for a while.)
This allows contbgscan() to correctly calculate if a scan should
continue based on ticks and ic->ic_lastdata .
Reviewed by: bz
Differential Revision: https://reviews.freebsd.org/D25031
2020-05-27 18:32:12 +00:00
|
|
|
if (scandone == 0 && (ss_priv->ss_iflags & ISCAN_PAUSE) == ISCAN_CANCEL) {
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
/* XXX printf? */
|
|
|
|
if_printf(vap->iv_ifp,
|
[net80211] Fix interrupted scan logic and ticks comparison
The scan task refactoring stuff circa 2014-2016 broke the blocking task
into a taskqueue with some async bits, but it apparently broke scans
being interrupted by traffic.
Notably - the new "field" SCAN_PAUSE sets both SCAN_INTERRUPT and SCAN_CANCEL,
and a bunch of existing code was checking for SCAN_CANCEL only and breaking
the scan. Unfortunately it was then (a) cancelling the scan entirely and
(b) not notifying userland that scan was done.
So:
* Update the calls to scan_end() to only pass in 1 (saying the scan is complete)
if SCAN_CANCEL is set WITHOUT SCAN_INTERRUPT. If both are set then yes,
the scan is interrupted, but it isn't canceled - it's just paused.
* Update the "did the scan flags change whilst the driver was called" logic
to check for canceled scans, not interrupted scans.
* The "scan done" logic now explicitly checks for either interrupted or
completed scans. This accounts for the situation where a scan is being
aborted via traffic but it ALSO happens to have finished (ie the last
channel was checked.)
This doesn't ENTIRELY fix scanning as the resume function is broken
due to incorrect ticks math. Thus, the second half of this patch
changes the ieee80211_ticks_*() macros to use int instead of long,
matching the logic that the TCP code does with ticks and handles
wrapping / negative ticks values. If cast to long then the wrapping
math wouldn't work right (ie, if ticks was actually negative,
ie, after the system has been up for a while.)
This allows contbgscan() to correctly calculate if a scan should
continue based on ticks and ic->ic_lastdata .
Reviewed by: bz
Differential Revision: https://reviews.freebsd.org/D25031
2020-05-27 18:32:12 +00:00
|
|
|
"%s: OOPS! scan cancelled during driver call (2) (ss_iflags=0x%x)!\n",
|
|
|
|
__func__,
|
|
|
|
ss_priv->ss_iflags);
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
scandone = 1;
|
|
|
|
}
|
|
|
|
|
2016-02-29 20:44:59 +00:00
|
|
|
scan_done(ss, scandone);
|
|
|
|
}
|
|
|
|
|
|
|
|
static void
|
|
|
|
scan_done(struct ieee80211_scan_state *ss, int scandone)
|
|
|
|
{
|
|
|
|
struct scan_state *ss_priv = SCAN_PRIVATE(ss);
|
|
|
|
struct ieee80211com *ic = ss->ss_ic;
|
|
|
|
struct ieee80211vap *vap = ss->ss_vap;
|
|
|
|
|
|
|
|
IEEE80211_LOCK_ASSERT(ic);
|
|
|
|
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
/*
|
|
|
|
* Clear the SCAN bit first in case frames are
|
|
|
|
* pending on the station power save queue. If
|
|
|
|
* we defer this then the dispatch of the frames
|
|
|
|
* may generate a request to cancel scanning.
|
|
|
|
*/
|
|
|
|
ic->ic_flags &= ~IEEE80211_F_SCAN;
|
2016-02-29 20:44:59 +00:00
|
|
|
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
/*
|
|
|
|
* Drop out of power save mode when a scan has
|
|
|
|
* completed. If this scan was prematurely terminated
|
|
|
|
* because it is a background scan then don't notify
|
|
|
|
* the ap; we'll either return to scanning after we
|
|
|
|
* receive the beacon frame or we'll drop out of power
|
|
|
|
* save mode because the beacon indicates we have frames
|
|
|
|
* waiting for us.
|
|
|
|
*/
|
|
|
|
if (scandone) {
|
2016-10-19 05:03:46 +00:00
|
|
|
/*
|
|
|
|
* If we're not a scan offload device, come back out of
|
|
|
|
* station powersave. Offload devices handle this themselves.
|
|
|
|
*/
|
|
|
|
if ((vap->iv_flags_ext & IEEE80211_FEXT_SCAN_OFFLOAD) == 0)
|
|
|
|
vap->iv_sta_ps(vap, 0);
|
[net80211] Fix interrupted scan logic and ticks comparison
The scan task refactoring stuff circa 2014-2016 broke the blocking task
into a taskqueue with some async bits, but it apparently broke scans
being interrupted by traffic.
Notably - the new "field" SCAN_PAUSE sets both SCAN_INTERRUPT and SCAN_CANCEL,
and a bunch of existing code was checking for SCAN_CANCEL only and breaking
the scan. Unfortunately it was then (a) cancelling the scan entirely and
(b) not notifying userland that scan was done.
So:
* Update the calls to scan_end() to only pass in 1 (saying the scan is complete)
if SCAN_CANCEL is set WITHOUT SCAN_INTERRUPT. If both are set then yes,
the scan is interrupted, but it isn't canceled - it's just paused.
* Update the "did the scan flags change whilst the driver was called" logic
to check for canceled scans, not interrupted scans.
* The "scan done" logic now explicitly checks for either interrupted or
completed scans. This accounts for the situation where a scan is being
aborted via traffic but it ALSO happens to have finished (ie the last
channel was checked.)
This doesn't ENTIRELY fix scanning as the resume function is broken
due to incorrect ticks math. Thus, the second half of this patch
changes the ieee80211_ticks_*() macros to use int instead of long,
matching the logic that the TCP code does with ticks and handles
wrapping / negative ticks values. If cast to long then the wrapping
math wouldn't work right (ie, if ticks was actually negative,
ie, after the system has been up for a while.)
This allows contbgscan() to correctly calculate if a scan should
continue based on ticks and ic->ic_lastdata .
Reviewed by: bz
Differential Revision: https://reviews.freebsd.org/D25031
2020-05-27 18:32:12 +00:00
|
|
|
if (ss->ss_next >= ss->ss_last) {
|
|
|
|
IEEE80211_DPRINTF(vap, IEEE80211_MSG_SCAN,
|
|
|
|
"%s: Dropping out of scan; ss_next=%u, ss_last=%u\n",
|
|
|
|
__func__,
|
|
|
|
(uint32_t) ss->ss_next,
|
|
|
|
(uint32_t) ss->ss_last);
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
ic->ic_flags_ext &= ~IEEE80211_FEXT_BGSCAN;
|
[net80211] Fix interrupted scan logic and ticks comparison
The scan task refactoring stuff circa 2014-2016 broke the blocking task
into a taskqueue with some async bits, but it apparently broke scans
being interrupted by traffic.
Notably - the new "field" SCAN_PAUSE sets both SCAN_INTERRUPT and SCAN_CANCEL,
and a bunch of existing code was checking for SCAN_CANCEL only and breaking
the scan. Unfortunately it was then (a) cancelling the scan entirely and
(b) not notifying userland that scan was done.
So:
* Update the calls to scan_end() to only pass in 1 (saying the scan is complete)
if SCAN_CANCEL is set WITHOUT SCAN_INTERRUPT. If both are set then yes,
the scan is interrupted, but it isn't canceled - it's just paused.
* Update the "did the scan flags change whilst the driver was called" logic
to check for canceled scans, not interrupted scans.
* The "scan done" logic now explicitly checks for either interrupted or
completed scans. This accounts for the situation where a scan is being
aborted via traffic but it ALSO happens to have finished (ie the last
channel was checked.)
This doesn't ENTIRELY fix scanning as the resume function is broken
due to incorrect ticks math. Thus, the second half of this patch
changes the ieee80211_ticks_*() macros to use int instead of long,
matching the logic that the TCP code does with ticks and handles
wrapping / negative ticks values. If cast to long then the wrapping
math wouldn't work right (ie, if ticks was actually negative,
ie, after the system has been up for a while.)
This allows contbgscan() to correctly calculate if a scan should
continue based on ticks and ic->ic_lastdata .
Reviewed by: bz
Differential Revision: https://reviews.freebsd.org/D25031
2020-05-27 18:32:12 +00:00
|
|
|
}
|
2016-05-21 23:21:42 +00:00
|
|
|
|
2016-09-30 18:43:39 +00:00
|
|
|
/* send 'scan done' event if not interrupted due to traffic. */
|
[net80211] Fix interrupted scan logic and ticks comparison
The scan task refactoring stuff circa 2014-2016 broke the blocking task
into a taskqueue with some async bits, but it apparently broke scans
being interrupted by traffic.
Notably - the new "field" SCAN_PAUSE sets both SCAN_INTERRUPT and SCAN_CANCEL,
and a bunch of existing code was checking for SCAN_CANCEL only and breaking
the scan. Unfortunately it was then (a) cancelling the scan entirely and
(b) not notifying userland that scan was done.
So:
* Update the calls to scan_end() to only pass in 1 (saying the scan is complete)
if SCAN_CANCEL is set WITHOUT SCAN_INTERRUPT. If both are set then yes,
the scan is interrupted, but it isn't canceled - it's just paused.
* Update the "did the scan flags change whilst the driver was called" logic
to check for canceled scans, not interrupted scans.
* The "scan done" logic now explicitly checks for either interrupted or
completed scans. This accounts for the situation where a scan is being
aborted via traffic but it ALSO happens to have finished (ie the last
channel was checked.)
This doesn't ENTIRELY fix scanning as the resume function is broken
due to incorrect ticks math. Thus, the second half of this patch
changes the ieee80211_ticks_*() macros to use int instead of long,
matching the logic that the TCP code does with ticks and handles
wrapping / negative ticks values. If cast to long then the wrapping
math wouldn't work right (ie, if ticks was actually negative,
ie, after the system has been up for a while.)
This allows contbgscan() to correctly calculate if a scan should
continue based on ticks and ic->ic_lastdata .
Reviewed by: bz
Differential Revision: https://reviews.freebsd.org/D25031
2020-05-27 18:32:12 +00:00
|
|
|
if (!(ss_priv->ss_iflags & ISCAN_INTERRUPT) ||
|
|
|
|
(ss->ss_next >= ss->ss_last))
|
2016-09-30 18:43:39 +00:00
|
|
|
ieee80211_notify_scan_done(vap);
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
}
|
2016-09-30 18:43:39 +00:00
|
|
|
ss_priv->ss_iflags &= ~(ISCAN_PAUSE | ISCAN_ABORT);
|
2016-02-29 20:41:10 +00:00
|
|
|
ss_priv->ss_scanend = 0;
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
ss->ss_flags &= ~(IEEE80211_SCAN_ONCE | IEEE80211_SCAN_PICK1ST);
|
|
|
|
IEEE80211_UNLOCK(ic);
|
|
|
|
#undef ISCAN_REP
|
|
|
|
}
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Process a beacon or probe response frame.
|
|
|
|
*/
|
2015-06-08 02:35:43 +00:00
|
|
|
static void
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
ieee80211_swscan_add_scan(struct ieee80211vap *vap,
|
Prepare for supporting driver-overridden curchan when submitting scan
results.
Right now the scan infrastructure assumes the channel is under net80211
control, and that when receiving beacon frames for scanning, the
current channel is indeed what ic_curchan is set to.
But firmware NICs with firmware scan support need more than this -
they can do background scans whilst hiding the off-channel behaviour
from net80211. Ie, net80211 still thinks everything is associated
and on the main channel, but it's getting scan results from all the
background traffic.
However sta_add() pays attention to ic_curchan and discards scan
results that aren't on the right channel. CCK beacon frames can be
decoded from adjacent channels so the receive path and sta_add
discard these as appropriate. This is fine for software scanning
like for ath(4), but not for firmware NICs. So with those, the
whole concept of background firmware scanning won't work without
major hacks (eg, overriding ic_curchan before calling the beacon
input / scan add.)
As part of my scan overhaul, modify sta_add() and the scan_add()
APIs to take an explicit current channel. The normal RX path
will set it to ic_curchan so it's a no-op. However, drivers may
decide to (eventually!) override the scan method to set the
"right" current channel based on what the firmware reports the
scan state is.
So for example, iwn, rsu and other NICs will eventually do this:
* driver issues scan start firmware command;
* firmware sends a "scan start on channel X" notify;
* firmware sends a bunch of beacon RX's as part of
the scan results;
* .. and the driver will replace scan_add() curchan with channel X,
so scan results are correct.
* firmware sends a "scan start on channel Y" notify;
* firmware sends more beacons...
* .. the driver replaces scan_add() curchan with channel Y.
Note:
* Eventually, net80211 should eventually grow the idea of a per-packet
current channel. It's possible in various modes (eg WAVE, P2P, etc)
that individual frames can come in from different channels and that
is under firmware control rather than driver/net80211 control, so
we should support that.
2015-05-10 22:07:53 +00:00
|
|
|
struct ieee80211_channel *curchan,
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
const struct ieee80211_scanparams *sp,
|
|
|
|
const struct ieee80211_frame *wh,
|
|
|
|
int subtype, int rssi, int noise)
|
|
|
|
{
|
|
|
|
struct ieee80211com *ic = vap->iv_ic;
|
|
|
|
struct ieee80211_scan_state *ss = ic->ic_scan;
|
|
|
|
|
|
|
|
/* XXX locking */
|
|
|
|
/*
|
|
|
|
* Frames received during startup are discarded to avoid
|
|
|
|
* using scan state setup on the initial entry to the timer
|
|
|
|
* callback. This can occur because the device may enable
|
|
|
|
* rx prior to our doing the initial channel change in the
|
|
|
|
* timer routine.
|
|
|
|
*/
|
|
|
|
if (SCAN_PRIVATE(ss)->ss_iflags & ISCAN_DISCARD)
|
|
|
|
return;
|
|
|
|
#ifdef IEEE80211_DEBUG
|
|
|
|
if (ieee80211_msg_scan(vap) && (ic->ic_flags & IEEE80211_F_SCAN))
|
|
|
|
ieee80211_scan_dump_probe_beacon(subtype, 1, wh->i_addr2, sp, rssi);
|
|
|
|
#endif
|
|
|
|
if (ss->ss_ops != NULL &&
|
Prepare for supporting driver-overridden curchan when submitting scan
results.
Right now the scan infrastructure assumes the channel is under net80211
control, and that when receiving beacon frames for scanning, the
current channel is indeed what ic_curchan is set to.
But firmware NICs with firmware scan support need more than this -
they can do background scans whilst hiding the off-channel behaviour
from net80211. Ie, net80211 still thinks everything is associated
and on the main channel, but it's getting scan results from all the
background traffic.
However sta_add() pays attention to ic_curchan and discards scan
results that aren't on the right channel. CCK beacon frames can be
decoded from adjacent channels so the receive path and sta_add
discard these as appropriate. This is fine for software scanning
like for ath(4), but not for firmware NICs. So with those, the
whole concept of background firmware scanning won't work without
major hacks (eg, overriding ic_curchan before calling the beacon
input / scan add.)
As part of my scan overhaul, modify sta_add() and the scan_add()
APIs to take an explicit current channel. The normal RX path
will set it to ic_curchan so it's a no-op. However, drivers may
decide to (eventually!) override the scan method to set the
"right" current channel based on what the firmware reports the
scan state is.
So for example, iwn, rsu and other NICs will eventually do this:
* driver issues scan start firmware command;
* firmware sends a "scan start on channel X" notify;
* firmware sends a bunch of beacon RX's as part of
the scan results;
* .. and the driver will replace scan_add() curchan with channel X,
so scan results are correct.
* firmware sends a "scan start on channel Y" notify;
* firmware sends more beacons...
* .. the driver replaces scan_add() curchan with channel Y.
Note:
* Eventually, net80211 should eventually grow the idea of a per-packet
current channel. It's possible in various modes (eg WAVE, P2P, etc)
that individual frames can come in from different channels and that
is under firmware control rather than driver/net80211 control, so
we should support that.
2015-05-10 22:07:53 +00:00
|
|
|
ss->ss_ops->scan_add(ss, curchan, sp, wh, subtype, rssi, noise)) {
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
/*
|
|
|
|
* If we've reached the min dwell time terminate
|
|
|
|
* the timer so we'll switch to the next channel.
|
|
|
|
*/
|
|
|
|
if ((SCAN_PRIVATE(ss)->ss_iflags & ISCAN_MINDWELL) == 0 &&
|
2016-03-30 00:44:10 +00:00
|
|
|
ieee80211_time_after_eq(ticks, SCAN_PRIVATE(ss)->ss_chanmindwell)) {
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
IEEE80211_DPRINTF(vap, IEEE80211_MSG_SCAN,
|
|
|
|
"%s: chan %3d%c min dwell met (%u > %lu)\n",
|
|
|
|
__func__,
|
|
|
|
ieee80211_chan2ieee(ic, ic->ic_curchan),
|
2015-01-06 18:25:10 +00:00
|
|
|
ieee80211_channel_type_char(ic->ic_curchan),
|
Refactor and split out the net80211 software scan engine from the rest
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
2015-01-06 02:08:45 +00:00
|
|
|
ticks, SCAN_PRIVATE(ss)->ss_chanmindwell);
|
|
|
|
SCAN_PRIVATE(ss)->ss_iflags |= ISCAN_MINDWELL;
|
|
|
|
/*
|
|
|
|
* NB: trigger at next clock tick or wait for the
|
|
|
|
* hardware.
|
|
|
|
*/
|
|
|
|
ic->ic_scan_mindwell(ss);
|
|
|
|
}
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
2015-06-08 02:35:43 +00:00
|
|
|
static struct ieee80211_scan_methods swscan_methods = {
|
|
|
|
.sc_attach = ieee80211_swscan_attach,
|
|
|
|
.sc_detach = ieee80211_swscan_detach,
|
|
|
|
.sc_vattach = ieee80211_swscan_vattach,
|
|
|
|
.sc_vdetach = ieee80211_swscan_vdetach,
|
|
|
|
.sc_set_scan_duration = ieee80211_swscan_set_scan_duration,
|
|
|
|
.sc_start_scan = ieee80211_swscan_start_scan,
|
|
|
|
.sc_check_scan = ieee80211_swscan_check_scan,
|
|
|
|
.sc_bg_scan = ieee80211_swscan_bg_scan,
|
|
|
|
.sc_cancel_scan = ieee80211_swscan_cancel_scan,
|
|
|
|
.sc_cancel_anyscan = ieee80211_swscan_cancel_anyscan,
|
|
|
|
.sc_scan_next = ieee80211_swscan_scan_next,
|
|
|
|
.sc_scan_done = ieee80211_swscan_scan_done,
|
|
|
|
.sc_scan_probe_curchan = ieee80211_swscan_probe_curchan,
|
|
|
|
.sc_add_scan = ieee80211_swscan_add_scan
|
|
|
|
};
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Default scan attach method.
|
|
|
|
*/
|
|
|
|
void
|
|
|
|
ieee80211_swscan_attach(struct ieee80211com *ic)
|
|
|
|
{
|
|
|
|
struct scan_state *ss;
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Setup the default methods
|
|
|
|
*/
|
|
|
|
ic->ic_scan_methods = &swscan_methods;
|
|
|
|
|
|
|
|
/* Allocate initial scan state */
|
|
|
|
ss = (struct scan_state *) IEEE80211_MALLOC(sizeof(struct scan_state),
|
|
|
|
M_80211_SCAN, IEEE80211_M_NOWAIT | IEEE80211_M_ZERO);
|
|
|
|
if (ss == NULL) {
|
|
|
|
ic->ic_scan = NULL;
|
|
|
|
return;
|
|
|
|
}
|
2016-02-29 20:53:27 +00:00
|
|
|
TASK_INIT(&ss->ss_scan_start, 0, scan_start, ss);
|
|
|
|
TIMEOUT_TASK_INIT(ic->ic_tq, &ss->ss_scan_curchan, 0,
|
|
|
|
scan_curchan_task, ss);
|
2015-06-08 02:35:43 +00:00
|
|
|
|
|
|
|
ic->ic_scan = &ss->base;
|
|
|
|
ss->base.ss_ic = ic;
|
|
|
|
|
|
|
|
ic->ic_scan_curchan = scan_curchan;
|
|
|
|
ic->ic_scan_mindwell = scan_mindwell;
|
|
|
|
}
|