freebsd-dev/contrib/wpa/COPYING

23 lines
965 B
Plaintext
Raw Normal View History

Import wpa_supplicant / hostapd 2.0. 2013-01-12 - v2.0 * added AP-STA-DISCONNECTED ctrl_iface event * improved debug logging (human readable event names, interface name included in more entries) * added number of small changes to make it easier for static analyzers to understand the implementation * added a workaround for Windows 7 Michael MIC failure reporting and use of the Secure bit in EAPOL-Key msg 3/4 * fixed number of small bugs (see git logs for more details) * changed OpenSSL to read full certificate chain from server_cert file * nl80211: number of updates to use new cfg80211/nl80211 functionality - replace monitor interface with nl80211 commands - additional information for driver-based AP SME * EAP-pwd: - fix KDF for group 21 and zero-padding - added support for fragmentation - increased maximum number of hunting-and-pecking iterations * avoid excessive Probe Response retries for broadcast Probe Request frames (only with drivers using hostapd SME/MLME) * added preliminary support for using TLS v1.2 (CONFIG_TLSV12=y) * fixed WPS operation stopping on dual concurrent AP * added wps_rf_bands configuration parameter for overriding RF Bands value for WPS * added support for getting per-device PSK from RADIUS Tunnel-Password * added support for libnl 3.2 and newer * increased initial group key handshake retransmit timeout to 500 ms * added a workaround for 4-way handshake to update SNonce even after having sent EAPOL-Key 3/4 to avoid issues with some supplicant implementations that can change SNonce for each EAP-Key 2/4 * added a workaround for EAPOL-Key 4/4 using incorrect type value in WPA2 mode (some deployed stations use WPA type in that message) * added a WPS workaround for mixed mode AP Settings with Windows 7 * changed WPS AP PIN disabling mechanism to disable the PIN after 10 consecutive failures in addition to using the exponential lockout period * added support for WFA Hotspot 2.0 - GAS/ANQP advertisement of network information - disable_dgaf parameter to disable downstream group-addressed forwarding * simplified licensing terms by selecting the BSD license as the only alternative * EAP-SIM: fixed re-authentication not to update pseudonym * EAP-SIM: use Notification round before EAP-Failure * EAP-AKA: added support for AT_COUNTER_TOO_SMALL * EAP-AKA: skip AKA/Identity exchange if EAP identity is recognized * EAP-AKA': fixed identity for MK derivation * EAP-AKA': updated to RFC 5448 (username prefixes changed); note: this breaks interoperability with older versions * EAP-SIM/AKA: allow pseudonym to be used after unknown reauth id * changed ANonce to be a random number instead of Counter-based * added support for canceling WPS operations with hostapd_cli wps_cancel * fixed EAP/WPS to PSK transition on reassociation in cases where deauthentication is missed * hlr_auc_gw enhancements: - a new command line parameter -u can be used to enable updating of SQN in Milenage file - use 5 bit IND for SQN updates - SQLite database can now be used to store Milenage information * EAP-SIM/AKA DB: added optional use of SQLite database for pseudonyms and reauth data * added support for Chargeable-User-Identity (RFC 4372) * added radius_auth_req_attr and radius_acct_req_attr configuration parameters to allow adding/overriding of RADIUS attributes in Access-Request and Accounting-Request packets * added support for RADIUS dynamic authorization server (RFC 5176) * added initial support for WNM operations - BSS max idle period - WNM-Sleep Mode * added new WPS NFC ctrl_iface mechanism - removed obsoleted WPS_OOB command (including support for deprecated UFD config_method) * added FT support for drivers that implement MLME internally * added SA Query support for drivers that implement MLME internally * removed default ACM=1 from AC_VO and AC_VI * changed VENDOR-TEST EAP method to use proper private enterprise number (this will not interoperate with older versions) * added hostapd.conf parameter vendor_elements to allow arbitrary vendor specific elements to be added to the Beacon and Probe Response frames * added support for configuring GCMP cipher for IEEE 802.11ad * added support for 256-bit AES with internal TLS implementation * changed EAPOL transmission to use AC_VO if WMM is active * fixed EAP-TLS/PEAP/TTLS/FAST server to validate TLS Message Length correctly; invalid messages could have caused the hostapd process to terminate before this fix [CVE-2012-4445] * limit number of active wildcard PINs for WPS Registrar to one to avoid confusing behavior with multiple wildcard PINs * added a workaround for WPS PBC session overlap detection to avoid interop issues with deployed station implementations that do not remove active PBC indication from Probe Request frames properly * added support for using SQLite for the eap_user database * added Acct-Session-Id attribute into Access-Request messages * fixed EAPOL frame transmission to non-QoS STAs with nl80211 (do not send QoS frames if the STA did not negotiate use of QoS for this association) 2012-05-10 - v1.0 * Add channel selection support in hostapd. See hostapd.conf. * Add support for IEEE 802.11v Time Advertisement mechanism with UTC TSF offset. See hostapd.conf for config info. * Delay STA entry removal until Deauth/Disassoc TX status in AP mode. This allows the driver to use PS buffering of Deauthentication and Disassociation frames when the STA is in power save sleep. Only available with drivers that provide TX status events for Deauth/ Disassoc frames (nl80211). * Allow PMKSA caching to be disabled on the Authenticator. See hostap.conf config parameter disable_pmksa_caching. * atheros: Add support for IEEE 802.11w configuration. * bsd: Add support for setting HT values in IFM_MMASK. * Allow client isolation to be configured with ap_isolate. Client isolation can be used to prevent low-level bridging of frames between associated stations in the BSS. By default, this bridging is allowed. * Allow coexistance of HT BSSes with WEP/TKIP BSSes. * Add require_ht config parameter, which can be used to configure hostapd to reject association with any station that does not support HT PHY. * Add support for writing debug log to a file using "-f" option. Also add relog CLI command to re-open the log file. * Add bridge handling for WDS STA interfaces. By default they are added to the configured bridge of the AP interface (if present), but the user can also specify a separate bridge using cli command wds_bridge. * hostapd_cli: - Add wds_bridge command for specifying bridge for WDS STA interfaces. - Add relog command for reopening log file. - Send AP-STA-DISCONNECTED event when an AP disconnects a station due to inactivity. - Add wps_config ctrl_interface command for configuring AP. This command can be used to configure the AP using the internal WPS registrar. It works in the same way as new AP settings received from an ER. - Many WPS/WPS ER commands - see WPS/WPS ER sections for details. - Add command get version, that returns hostapd version string. * WNM: Add BSS Transition Management Request for ESS Disassoc Imminent. Use hostapd_cli ess_disassoc (STA addr) (URL) to send the notification to the STA. * Allow AP mode to disconnect STAs based on low ACK condition (when the data connection is not working properly, e.g., due to the STA going outside the range of the AP). Disabled by default, enable by config option disassoc_low_ack. * Add WPA_IGNORE_CONFIG_ERRORS build option to continue in case of bad config file. * WPS: - Send AP Settings as a wrapped Credential attribute to ctrl_iface in WPS-NEW-AP-SETTINGS. - Dispatch more WPS events through hostapd ctrl_iface. - Add mechanism for indicating non-standard WPS errors. - Change concurrent radio AP to use only one WPS UPnP instance. - Add wps_check_pin command for processing PIN from user input. UIs can use this command to process a PIN entered by a user and to validate the checksum digit (if present). - Add hostap_cli get_config command to display current AP config. - Add new hostapd_cli command, wps_ap_pin, to manage AP PIN at runtime and support dynamic AP PIN management. - Disable AP PIN after 10 consecutive failures. Slow down attacks on failures up to 10. - Allow AP to start in Enrollee mode without AP PIN for probing, to be compatible with Windows 7. - Add Config Error into WPS-FAIL events to provide more info to the user on how to resolve the issue. - When controlling multiple interfaces: - apply WPS commands to all interfaces configured to use WPS - apply WPS config changes to all interfaces that use WPS - when an attack is detected on any interface, disable AP PIN on all interfaces * WPS ER: - Show SetSelectedRegistrar events as ctrl_iface events. - Add special AP Setup Locked mode to allow read only ER. ap_setup_locked=2 can now be used to enable a special mode where WPS ER can learn the current AP settings, but cannot change them. * WPS 2.0: Add support for WPS 2.0 (CONFIG_WPS2) - Add build option CONFIG_WPS_EXTENSIBILITY_TESTING to enable tool for testing protocol extensibility. - Add build option CONFIG_WPS_STRICT to allow disabling of WPS workarounds. - Add support for AuthorizedMACs attribute. * TDLS: - Allow TDLS use or TDLS channel switching in the BSS to be prohibited in the BSS, using config params tdls_prohibit and tdls_prohibit_chan_switch. * EAP server: Add support for configuring fragment size (see fragment_size in hostapd.conf). * wlantest: Add a tool wlantest for IEEE802.11 protocol testing. wlantest can be used to capture frames from a monitor interface for realtime capturing or from pcap files for offline analysis. * Interworking: Support added for 802.11u. Enable in .config with CONFIG_INTERWORKING. See hostapd.conf for config parameters for interworking. * Android: Add build and runtime support for Android hostapd. * Add a new debug message level for excessive information. Use -ddd to enable. * TLS: Add support for tls_disable_time_checks=1 in client mode. * Internal TLS: - Add support for TLS v1.1 (RFC 4346). Enable with build parameter CONFIG_TLSV11. - Add domainComponent parser for X.509 names * Reorder some IEs to get closer to IEEE 802.11 standard. Move WMM into end of Beacon, Probe Resp and (Re)Assoc Resp frames. Move HT IEs to be later in (Re)Assoc Resp. * Many bugfixes.
2013-06-25 02:47:41 +00:00
wpa_supplicant and hostapd
--------------------------
2019-04-22 15:42:53 +00:00
Copyright (c) 2002-2019, Jouni Malinen <j@w1.fi> and contributors
Import wpa_supplicant / hostapd 2.0. 2013-01-12 - v2.0 * added AP-STA-DISCONNECTED ctrl_iface event * improved debug logging (human readable event names, interface name included in more entries) * added number of small changes to make it easier for static analyzers to understand the implementation * added a workaround for Windows 7 Michael MIC failure reporting and use of the Secure bit in EAPOL-Key msg 3/4 * fixed number of small bugs (see git logs for more details) * changed OpenSSL to read full certificate chain from server_cert file * nl80211: number of updates to use new cfg80211/nl80211 functionality - replace monitor interface with nl80211 commands - additional information for driver-based AP SME * EAP-pwd: - fix KDF for group 21 and zero-padding - added support for fragmentation - increased maximum number of hunting-and-pecking iterations * avoid excessive Probe Response retries for broadcast Probe Request frames (only with drivers using hostapd SME/MLME) * added preliminary support for using TLS v1.2 (CONFIG_TLSV12=y) * fixed WPS operation stopping on dual concurrent AP * added wps_rf_bands configuration parameter for overriding RF Bands value for WPS * added support for getting per-device PSK from RADIUS Tunnel-Password * added support for libnl 3.2 and newer * increased initial group key handshake retransmit timeout to 500 ms * added a workaround for 4-way handshake to update SNonce even after having sent EAPOL-Key 3/4 to avoid issues with some supplicant implementations that can change SNonce for each EAP-Key 2/4 * added a workaround for EAPOL-Key 4/4 using incorrect type value in WPA2 mode (some deployed stations use WPA type in that message) * added a WPS workaround for mixed mode AP Settings with Windows 7 * changed WPS AP PIN disabling mechanism to disable the PIN after 10 consecutive failures in addition to using the exponential lockout period * added support for WFA Hotspot 2.0 - GAS/ANQP advertisement of network information - disable_dgaf parameter to disable downstream group-addressed forwarding * simplified licensing terms by selecting the BSD license as the only alternative * EAP-SIM: fixed re-authentication not to update pseudonym * EAP-SIM: use Notification round before EAP-Failure * EAP-AKA: added support for AT_COUNTER_TOO_SMALL * EAP-AKA: skip AKA/Identity exchange if EAP identity is recognized * EAP-AKA': fixed identity for MK derivation * EAP-AKA': updated to RFC 5448 (username prefixes changed); note: this breaks interoperability with older versions * EAP-SIM/AKA: allow pseudonym to be used after unknown reauth id * changed ANonce to be a random number instead of Counter-based * added support for canceling WPS operations with hostapd_cli wps_cancel * fixed EAP/WPS to PSK transition on reassociation in cases where deauthentication is missed * hlr_auc_gw enhancements: - a new command line parameter -u can be used to enable updating of SQN in Milenage file - use 5 bit IND for SQN updates - SQLite database can now be used to store Milenage information * EAP-SIM/AKA DB: added optional use of SQLite database for pseudonyms and reauth data * added support for Chargeable-User-Identity (RFC 4372) * added radius_auth_req_attr and radius_acct_req_attr configuration parameters to allow adding/overriding of RADIUS attributes in Access-Request and Accounting-Request packets * added support for RADIUS dynamic authorization server (RFC 5176) * added initial support for WNM operations - BSS max idle period - WNM-Sleep Mode * added new WPS NFC ctrl_iface mechanism - removed obsoleted WPS_OOB command (including support for deprecated UFD config_method) * added FT support for drivers that implement MLME internally * added SA Query support for drivers that implement MLME internally * removed default ACM=1 from AC_VO and AC_VI * changed VENDOR-TEST EAP method to use proper private enterprise number (this will not interoperate with older versions) * added hostapd.conf parameter vendor_elements to allow arbitrary vendor specific elements to be added to the Beacon and Probe Response frames * added support for configuring GCMP cipher for IEEE 802.11ad * added support for 256-bit AES with internal TLS implementation * changed EAPOL transmission to use AC_VO if WMM is active * fixed EAP-TLS/PEAP/TTLS/FAST server to validate TLS Message Length correctly; invalid messages could have caused the hostapd process to terminate before this fix [CVE-2012-4445] * limit number of active wildcard PINs for WPS Registrar to one to avoid confusing behavior with multiple wildcard PINs * added a workaround for WPS PBC session overlap detection to avoid interop issues with deployed station implementations that do not remove active PBC indication from Probe Request frames properly * added support for using SQLite for the eap_user database * added Acct-Session-Id attribute into Access-Request messages * fixed EAPOL frame transmission to non-QoS STAs with nl80211 (do not send QoS frames if the STA did not negotiate use of QoS for this association) 2012-05-10 - v1.0 * Add channel selection support in hostapd. See hostapd.conf. * Add support for IEEE 802.11v Time Advertisement mechanism with UTC TSF offset. See hostapd.conf for config info. * Delay STA entry removal until Deauth/Disassoc TX status in AP mode. This allows the driver to use PS buffering of Deauthentication and Disassociation frames when the STA is in power save sleep. Only available with drivers that provide TX status events for Deauth/ Disassoc frames (nl80211). * Allow PMKSA caching to be disabled on the Authenticator. See hostap.conf config parameter disable_pmksa_caching. * atheros: Add support for IEEE 802.11w configuration. * bsd: Add support for setting HT values in IFM_MMASK. * Allow client isolation to be configured with ap_isolate. Client isolation can be used to prevent low-level bridging of frames between associated stations in the BSS. By default, this bridging is allowed. * Allow coexistance of HT BSSes with WEP/TKIP BSSes. * Add require_ht config parameter, which can be used to configure hostapd to reject association with any station that does not support HT PHY. * Add support for writing debug log to a file using "-f" option. Also add relog CLI command to re-open the log file. * Add bridge handling for WDS STA interfaces. By default they are added to the configured bridge of the AP interface (if present), but the user can also specify a separate bridge using cli command wds_bridge. * hostapd_cli: - Add wds_bridge command for specifying bridge for WDS STA interfaces. - Add relog command for reopening log file. - Send AP-STA-DISCONNECTED event when an AP disconnects a station due to inactivity. - Add wps_config ctrl_interface command for configuring AP. This command can be used to configure the AP using the internal WPS registrar. It works in the same way as new AP settings received from an ER. - Many WPS/WPS ER commands - see WPS/WPS ER sections for details. - Add command get version, that returns hostapd version string. * WNM: Add BSS Transition Management Request for ESS Disassoc Imminent. Use hostapd_cli ess_disassoc (STA addr) (URL) to send the notification to the STA. * Allow AP mode to disconnect STAs based on low ACK condition (when the data connection is not working properly, e.g., due to the STA going outside the range of the AP). Disabled by default, enable by config option disassoc_low_ack. * Add WPA_IGNORE_CONFIG_ERRORS build option to continue in case of bad config file. * WPS: - Send AP Settings as a wrapped Credential attribute to ctrl_iface in WPS-NEW-AP-SETTINGS. - Dispatch more WPS events through hostapd ctrl_iface. - Add mechanism for indicating non-standard WPS errors. - Change concurrent radio AP to use only one WPS UPnP instance. - Add wps_check_pin command for processing PIN from user input. UIs can use this command to process a PIN entered by a user and to validate the checksum digit (if present). - Add hostap_cli get_config command to display current AP config. - Add new hostapd_cli command, wps_ap_pin, to manage AP PIN at runtime and support dynamic AP PIN management. - Disable AP PIN after 10 consecutive failures. Slow down attacks on failures up to 10. - Allow AP to start in Enrollee mode without AP PIN for probing, to be compatible with Windows 7. - Add Config Error into WPS-FAIL events to provide more info to the user on how to resolve the issue. - When controlling multiple interfaces: - apply WPS commands to all interfaces configured to use WPS - apply WPS config changes to all interfaces that use WPS - when an attack is detected on any interface, disable AP PIN on all interfaces * WPS ER: - Show SetSelectedRegistrar events as ctrl_iface events. - Add special AP Setup Locked mode to allow read only ER. ap_setup_locked=2 can now be used to enable a special mode where WPS ER can learn the current AP settings, but cannot change them. * WPS 2.0: Add support for WPS 2.0 (CONFIG_WPS2) - Add build option CONFIG_WPS_EXTENSIBILITY_TESTING to enable tool for testing protocol extensibility. - Add build option CONFIG_WPS_STRICT to allow disabling of WPS workarounds. - Add support for AuthorizedMACs attribute. * TDLS: - Allow TDLS use or TDLS channel switching in the BSS to be prohibited in the BSS, using config params tdls_prohibit and tdls_prohibit_chan_switch. * EAP server: Add support for configuring fragment size (see fragment_size in hostapd.conf). * wlantest: Add a tool wlantest for IEEE802.11 protocol testing. wlantest can be used to capture frames from a monitor interface for realtime capturing or from pcap files for offline analysis. * Interworking: Support added for 802.11u. Enable in .config with CONFIG_INTERWORKING. See hostapd.conf for config parameters for interworking. * Android: Add build and runtime support for Android hostapd. * Add a new debug message level for excessive information. Use -ddd to enable. * TLS: Add support for tls_disable_time_checks=1 in client mode. * Internal TLS: - Add support for TLS v1.1 (RFC 4346). Enable with build parameter CONFIG_TLSV11. - Add domainComponent parser for X.509 names * Reorder some IEs to get closer to IEEE 802.11 standard. Move WMM into end of Beacon, Probe Resp and (Re)Assoc Resp frames. Move HT IEs to be later in (Re)Assoc Resp. * Many bugfixes.
2013-06-25 02:47:41 +00:00
All Rights Reserved.
Import wpa_supplicant / hostapd 2.0. 2013-01-12 - v2.0 * added AP-STA-DISCONNECTED ctrl_iface event * improved debug logging (human readable event names, interface name included in more entries) * added number of small changes to make it easier for static analyzers to understand the implementation * added a workaround for Windows 7 Michael MIC failure reporting and use of the Secure bit in EAPOL-Key msg 3/4 * fixed number of small bugs (see git logs for more details) * changed OpenSSL to read full certificate chain from server_cert file * nl80211: number of updates to use new cfg80211/nl80211 functionality - replace monitor interface with nl80211 commands - additional information for driver-based AP SME * EAP-pwd: - fix KDF for group 21 and zero-padding - added support for fragmentation - increased maximum number of hunting-and-pecking iterations * avoid excessive Probe Response retries for broadcast Probe Request frames (only with drivers using hostapd SME/MLME) * added preliminary support for using TLS v1.2 (CONFIG_TLSV12=y) * fixed WPS operation stopping on dual concurrent AP * added wps_rf_bands configuration parameter for overriding RF Bands value for WPS * added support for getting per-device PSK from RADIUS Tunnel-Password * added support for libnl 3.2 and newer * increased initial group key handshake retransmit timeout to 500 ms * added a workaround for 4-way handshake to update SNonce even after having sent EAPOL-Key 3/4 to avoid issues with some supplicant implementations that can change SNonce for each EAP-Key 2/4 * added a workaround for EAPOL-Key 4/4 using incorrect type value in WPA2 mode (some deployed stations use WPA type in that message) * added a WPS workaround for mixed mode AP Settings with Windows 7 * changed WPS AP PIN disabling mechanism to disable the PIN after 10 consecutive failures in addition to using the exponential lockout period * added support for WFA Hotspot 2.0 - GAS/ANQP advertisement of network information - disable_dgaf parameter to disable downstream group-addressed forwarding * simplified licensing terms by selecting the BSD license as the only alternative * EAP-SIM: fixed re-authentication not to update pseudonym * EAP-SIM: use Notification round before EAP-Failure * EAP-AKA: added support for AT_COUNTER_TOO_SMALL * EAP-AKA: skip AKA/Identity exchange if EAP identity is recognized * EAP-AKA': fixed identity for MK derivation * EAP-AKA': updated to RFC 5448 (username prefixes changed); note: this breaks interoperability with older versions * EAP-SIM/AKA: allow pseudonym to be used after unknown reauth id * changed ANonce to be a random number instead of Counter-based * added support for canceling WPS operations with hostapd_cli wps_cancel * fixed EAP/WPS to PSK transition on reassociation in cases where deauthentication is missed * hlr_auc_gw enhancements: - a new command line parameter -u can be used to enable updating of SQN in Milenage file - use 5 bit IND for SQN updates - SQLite database can now be used to store Milenage information * EAP-SIM/AKA DB: added optional use of SQLite database for pseudonyms and reauth data * added support for Chargeable-User-Identity (RFC 4372) * added radius_auth_req_attr and radius_acct_req_attr configuration parameters to allow adding/overriding of RADIUS attributes in Access-Request and Accounting-Request packets * added support for RADIUS dynamic authorization server (RFC 5176) * added initial support for WNM operations - BSS max idle period - WNM-Sleep Mode * added new WPS NFC ctrl_iface mechanism - removed obsoleted WPS_OOB command (including support for deprecated UFD config_method) * added FT support for drivers that implement MLME internally * added SA Query support for drivers that implement MLME internally * removed default ACM=1 from AC_VO and AC_VI * changed VENDOR-TEST EAP method to use proper private enterprise number (this will not interoperate with older versions) * added hostapd.conf parameter vendor_elements to allow arbitrary vendor specific elements to be added to the Beacon and Probe Response frames * added support for configuring GCMP cipher for IEEE 802.11ad * added support for 256-bit AES with internal TLS implementation * changed EAPOL transmission to use AC_VO if WMM is active * fixed EAP-TLS/PEAP/TTLS/FAST server to validate TLS Message Length correctly; invalid messages could have caused the hostapd process to terminate before this fix [CVE-2012-4445] * limit number of active wildcard PINs for WPS Registrar to one to avoid confusing behavior with multiple wildcard PINs * added a workaround for WPS PBC session overlap detection to avoid interop issues with deployed station implementations that do not remove active PBC indication from Probe Request frames properly * added support for using SQLite for the eap_user database * added Acct-Session-Id attribute into Access-Request messages * fixed EAPOL frame transmission to non-QoS STAs with nl80211 (do not send QoS frames if the STA did not negotiate use of QoS for this association) 2012-05-10 - v1.0 * Add channel selection support in hostapd. See hostapd.conf. * Add support for IEEE 802.11v Time Advertisement mechanism with UTC TSF offset. See hostapd.conf for config info. * Delay STA entry removal until Deauth/Disassoc TX status in AP mode. This allows the driver to use PS buffering of Deauthentication and Disassociation frames when the STA is in power save sleep. Only available with drivers that provide TX status events for Deauth/ Disassoc frames (nl80211). * Allow PMKSA caching to be disabled on the Authenticator. See hostap.conf config parameter disable_pmksa_caching. * atheros: Add support for IEEE 802.11w configuration. * bsd: Add support for setting HT values in IFM_MMASK. * Allow client isolation to be configured with ap_isolate. Client isolation can be used to prevent low-level bridging of frames between associated stations in the BSS. By default, this bridging is allowed. * Allow coexistance of HT BSSes with WEP/TKIP BSSes. * Add require_ht config parameter, which can be used to configure hostapd to reject association with any station that does not support HT PHY. * Add support for writing debug log to a file using "-f" option. Also add relog CLI command to re-open the log file. * Add bridge handling for WDS STA interfaces. By default they are added to the configured bridge of the AP interface (if present), but the user can also specify a separate bridge using cli command wds_bridge. * hostapd_cli: - Add wds_bridge command for specifying bridge for WDS STA interfaces. - Add relog command for reopening log file. - Send AP-STA-DISCONNECTED event when an AP disconnects a station due to inactivity. - Add wps_config ctrl_interface command for configuring AP. This command can be used to configure the AP using the internal WPS registrar. It works in the same way as new AP settings received from an ER. - Many WPS/WPS ER commands - see WPS/WPS ER sections for details. - Add command get version, that returns hostapd version string. * WNM: Add BSS Transition Management Request for ESS Disassoc Imminent. Use hostapd_cli ess_disassoc (STA addr) (URL) to send the notification to the STA. * Allow AP mode to disconnect STAs based on low ACK condition (when the data connection is not working properly, e.g., due to the STA going outside the range of the AP). Disabled by default, enable by config option disassoc_low_ack. * Add WPA_IGNORE_CONFIG_ERRORS build option to continue in case of bad config file. * WPS: - Send AP Settings as a wrapped Credential attribute to ctrl_iface in WPS-NEW-AP-SETTINGS. - Dispatch more WPS events through hostapd ctrl_iface. - Add mechanism for indicating non-standard WPS errors. - Change concurrent radio AP to use only one WPS UPnP instance. - Add wps_check_pin command for processing PIN from user input. UIs can use this command to process a PIN entered by a user and to validate the checksum digit (if present). - Add hostap_cli get_config command to display current AP config. - Add new hostapd_cli command, wps_ap_pin, to manage AP PIN at runtime and support dynamic AP PIN management. - Disable AP PIN after 10 consecutive failures. Slow down attacks on failures up to 10. - Allow AP to start in Enrollee mode without AP PIN for probing, to be compatible with Windows 7. - Add Config Error into WPS-FAIL events to provide more info to the user on how to resolve the issue. - When controlling multiple interfaces: - apply WPS commands to all interfaces configured to use WPS - apply WPS config changes to all interfaces that use WPS - when an attack is detected on any interface, disable AP PIN on all interfaces * WPS ER: - Show SetSelectedRegistrar events as ctrl_iface events. - Add special AP Setup Locked mode to allow read only ER. ap_setup_locked=2 can now be used to enable a special mode where WPS ER can learn the current AP settings, but cannot change them. * WPS 2.0: Add support for WPS 2.0 (CONFIG_WPS2) - Add build option CONFIG_WPS_EXTENSIBILITY_TESTING to enable tool for testing protocol extensibility. - Add build option CONFIG_WPS_STRICT to allow disabling of WPS workarounds. - Add support for AuthorizedMACs attribute. * TDLS: - Allow TDLS use or TDLS channel switching in the BSS to be prohibited in the BSS, using config params tdls_prohibit and tdls_prohibit_chan_switch. * EAP server: Add support for configuring fragment size (see fragment_size in hostapd.conf). * wlantest: Add a tool wlantest for IEEE802.11 protocol testing. wlantest can be used to capture frames from a monitor interface for realtime capturing or from pcap files for offline analysis. * Interworking: Support added for 802.11u. Enable in .config with CONFIG_INTERWORKING. See hostapd.conf for config parameters for interworking. * Android: Add build and runtime support for Android hostapd. * Add a new debug message level for excessive information. Use -ddd to enable. * TLS: Add support for tls_disable_time_checks=1 in client mode. * Internal TLS: - Add support for TLS v1.1 (RFC 4346). Enable with build parameter CONFIG_TLSV11. - Add domainComponent parser for X.509 names * Reorder some IEs to get closer to IEEE 802.11 standard. Move WMM into end of Beacon, Probe Resp and (Re)Assoc Resp frames. Move HT IEs to be later in (Re)Assoc Resp. * Many bugfixes.
2013-06-25 02:47:41 +00:00
See the README file for the current license terms.
Import wpa_supplicant / hostapd 2.0. 2013-01-12 - v2.0 * added AP-STA-DISCONNECTED ctrl_iface event * improved debug logging (human readable event names, interface name included in more entries) * added number of small changes to make it easier for static analyzers to understand the implementation * added a workaround for Windows 7 Michael MIC failure reporting and use of the Secure bit in EAPOL-Key msg 3/4 * fixed number of small bugs (see git logs for more details) * changed OpenSSL to read full certificate chain from server_cert file * nl80211: number of updates to use new cfg80211/nl80211 functionality - replace monitor interface with nl80211 commands - additional information for driver-based AP SME * EAP-pwd: - fix KDF for group 21 and zero-padding - added support for fragmentation - increased maximum number of hunting-and-pecking iterations * avoid excessive Probe Response retries for broadcast Probe Request frames (only with drivers using hostapd SME/MLME) * added preliminary support for using TLS v1.2 (CONFIG_TLSV12=y) * fixed WPS operation stopping on dual concurrent AP * added wps_rf_bands configuration parameter for overriding RF Bands value for WPS * added support for getting per-device PSK from RADIUS Tunnel-Password * added support for libnl 3.2 and newer * increased initial group key handshake retransmit timeout to 500 ms * added a workaround for 4-way handshake to update SNonce even after having sent EAPOL-Key 3/4 to avoid issues with some supplicant implementations that can change SNonce for each EAP-Key 2/4 * added a workaround for EAPOL-Key 4/4 using incorrect type value in WPA2 mode (some deployed stations use WPA type in that message) * added a WPS workaround for mixed mode AP Settings with Windows 7 * changed WPS AP PIN disabling mechanism to disable the PIN after 10 consecutive failures in addition to using the exponential lockout period * added support for WFA Hotspot 2.0 - GAS/ANQP advertisement of network information - disable_dgaf parameter to disable downstream group-addressed forwarding * simplified licensing terms by selecting the BSD license as the only alternative * EAP-SIM: fixed re-authentication not to update pseudonym * EAP-SIM: use Notification round before EAP-Failure * EAP-AKA: added support for AT_COUNTER_TOO_SMALL * EAP-AKA: skip AKA/Identity exchange if EAP identity is recognized * EAP-AKA': fixed identity for MK derivation * EAP-AKA': updated to RFC 5448 (username prefixes changed); note: this breaks interoperability with older versions * EAP-SIM/AKA: allow pseudonym to be used after unknown reauth id * changed ANonce to be a random number instead of Counter-based * added support for canceling WPS operations with hostapd_cli wps_cancel * fixed EAP/WPS to PSK transition on reassociation in cases where deauthentication is missed * hlr_auc_gw enhancements: - a new command line parameter -u can be used to enable updating of SQN in Milenage file - use 5 bit IND for SQN updates - SQLite database can now be used to store Milenage information * EAP-SIM/AKA DB: added optional use of SQLite database for pseudonyms and reauth data * added support for Chargeable-User-Identity (RFC 4372) * added radius_auth_req_attr and radius_acct_req_attr configuration parameters to allow adding/overriding of RADIUS attributes in Access-Request and Accounting-Request packets * added support for RADIUS dynamic authorization server (RFC 5176) * added initial support for WNM operations - BSS max idle period - WNM-Sleep Mode * added new WPS NFC ctrl_iface mechanism - removed obsoleted WPS_OOB command (including support for deprecated UFD config_method) * added FT support for drivers that implement MLME internally * added SA Query support for drivers that implement MLME internally * removed default ACM=1 from AC_VO and AC_VI * changed VENDOR-TEST EAP method to use proper private enterprise number (this will not interoperate with older versions) * added hostapd.conf parameter vendor_elements to allow arbitrary vendor specific elements to be added to the Beacon and Probe Response frames * added support for configuring GCMP cipher for IEEE 802.11ad * added support for 256-bit AES with internal TLS implementation * changed EAPOL transmission to use AC_VO if WMM is active * fixed EAP-TLS/PEAP/TTLS/FAST server to validate TLS Message Length correctly; invalid messages could have caused the hostapd process to terminate before this fix [CVE-2012-4445] * limit number of active wildcard PINs for WPS Registrar to one to avoid confusing behavior with multiple wildcard PINs * added a workaround for WPS PBC session overlap detection to avoid interop issues with deployed station implementations that do not remove active PBC indication from Probe Request frames properly * added support for using SQLite for the eap_user database * added Acct-Session-Id attribute into Access-Request messages * fixed EAPOL frame transmission to non-QoS STAs with nl80211 (do not send QoS frames if the STA did not negotiate use of QoS for this association) 2012-05-10 - v1.0 * Add channel selection support in hostapd. See hostapd.conf. * Add support for IEEE 802.11v Time Advertisement mechanism with UTC TSF offset. See hostapd.conf for config info. * Delay STA entry removal until Deauth/Disassoc TX status in AP mode. This allows the driver to use PS buffering of Deauthentication and Disassociation frames when the STA is in power save sleep. Only available with drivers that provide TX status events for Deauth/ Disassoc frames (nl80211). * Allow PMKSA caching to be disabled on the Authenticator. See hostap.conf config parameter disable_pmksa_caching. * atheros: Add support for IEEE 802.11w configuration. * bsd: Add support for setting HT values in IFM_MMASK. * Allow client isolation to be configured with ap_isolate. Client isolation can be used to prevent low-level bridging of frames between associated stations in the BSS. By default, this bridging is allowed. * Allow coexistance of HT BSSes with WEP/TKIP BSSes. * Add require_ht config parameter, which can be used to configure hostapd to reject association with any station that does not support HT PHY. * Add support for writing debug log to a file using "-f" option. Also add relog CLI command to re-open the log file. * Add bridge handling for WDS STA interfaces. By default they are added to the configured bridge of the AP interface (if present), but the user can also specify a separate bridge using cli command wds_bridge. * hostapd_cli: - Add wds_bridge command for specifying bridge for WDS STA interfaces. - Add relog command for reopening log file. - Send AP-STA-DISCONNECTED event when an AP disconnects a station due to inactivity. - Add wps_config ctrl_interface command for configuring AP. This command can be used to configure the AP using the internal WPS registrar. It works in the same way as new AP settings received from an ER. - Many WPS/WPS ER commands - see WPS/WPS ER sections for details. - Add command get version, that returns hostapd version string. * WNM: Add BSS Transition Management Request for ESS Disassoc Imminent. Use hostapd_cli ess_disassoc (STA addr) (URL) to send the notification to the STA. * Allow AP mode to disconnect STAs based on low ACK condition (when the data connection is not working properly, e.g., due to the STA going outside the range of the AP). Disabled by default, enable by config option disassoc_low_ack. * Add WPA_IGNORE_CONFIG_ERRORS build option to continue in case of bad config file. * WPS: - Send AP Settings as a wrapped Credential attribute to ctrl_iface in WPS-NEW-AP-SETTINGS. - Dispatch more WPS events through hostapd ctrl_iface. - Add mechanism for indicating non-standard WPS errors. - Change concurrent radio AP to use only one WPS UPnP instance. - Add wps_check_pin command for processing PIN from user input. UIs can use this command to process a PIN entered by a user and to validate the checksum digit (if present). - Add hostap_cli get_config command to display current AP config. - Add new hostapd_cli command, wps_ap_pin, to manage AP PIN at runtime and support dynamic AP PIN management. - Disable AP PIN after 10 consecutive failures. Slow down attacks on failures up to 10. - Allow AP to start in Enrollee mode without AP PIN for probing, to be compatible with Windows 7. - Add Config Error into WPS-FAIL events to provide more info to the user on how to resolve the issue. - When controlling multiple interfaces: - apply WPS commands to all interfaces configured to use WPS - apply WPS config changes to all interfaces that use WPS - when an attack is detected on any interface, disable AP PIN on all interfaces * WPS ER: - Show SetSelectedRegistrar events as ctrl_iface events. - Add special AP Setup Locked mode to allow read only ER. ap_setup_locked=2 can now be used to enable a special mode where WPS ER can learn the current AP settings, but cannot change them. * WPS 2.0: Add support for WPS 2.0 (CONFIG_WPS2) - Add build option CONFIG_WPS_EXTENSIBILITY_TESTING to enable tool for testing protocol extensibility. - Add build option CONFIG_WPS_STRICT to allow disabling of WPS workarounds. - Add support for AuthorizedMACs attribute. * TDLS: - Allow TDLS use or TDLS channel switching in the BSS to be prohibited in the BSS, using config params tdls_prohibit and tdls_prohibit_chan_switch. * EAP server: Add support for configuring fragment size (see fragment_size in hostapd.conf). * wlantest: Add a tool wlantest for IEEE802.11 protocol testing. wlantest can be used to capture frames from a monitor interface for realtime capturing or from pcap files for offline analysis. * Interworking: Support added for 802.11u. Enable in .config with CONFIG_INTERWORKING. See hostapd.conf for config parameters for interworking. * Android: Add build and runtime support for Android hostapd. * Add a new debug message level for excessive information. Use -ddd to enable. * TLS: Add support for tls_disable_time_checks=1 in client mode. * Internal TLS: - Add support for TLS v1.1 (RFC 4346). Enable with build parameter CONFIG_TLSV11. - Add domainComponent parser for X.509 names * Reorder some IEs to get closer to IEEE 802.11 standard. Move WMM into end of Beacon, Probe Resp and (Re)Assoc Resp frames. Move HT IEs to be later in (Re)Assoc Resp. * Many bugfixes.
2013-06-25 02:47:41 +00:00
This software was previously distributed under BSD/GPL v2 dual license
terms that allowed either of those license alternatives to be
selected. As of February 11, 2012, the project has chosen to use only
the BSD license option for future distribution. As such, the GPL v2
license option is no longer used. It should be noted that the BSD
license option (the one with advertisement clause removed) is compatible
with GPL and as such, does not prevent use of this software in projects
that use GPL.
Import wpa_supplicant / hostapd 2.0. 2013-01-12 - v2.0 * added AP-STA-DISCONNECTED ctrl_iface event * improved debug logging (human readable event names, interface name included in more entries) * added number of small changes to make it easier for static analyzers to understand the implementation * added a workaround for Windows 7 Michael MIC failure reporting and use of the Secure bit in EAPOL-Key msg 3/4 * fixed number of small bugs (see git logs for more details) * changed OpenSSL to read full certificate chain from server_cert file * nl80211: number of updates to use new cfg80211/nl80211 functionality - replace monitor interface with nl80211 commands - additional information for driver-based AP SME * EAP-pwd: - fix KDF for group 21 and zero-padding - added support for fragmentation - increased maximum number of hunting-and-pecking iterations * avoid excessive Probe Response retries for broadcast Probe Request frames (only with drivers using hostapd SME/MLME) * added preliminary support for using TLS v1.2 (CONFIG_TLSV12=y) * fixed WPS operation stopping on dual concurrent AP * added wps_rf_bands configuration parameter for overriding RF Bands value for WPS * added support for getting per-device PSK from RADIUS Tunnel-Password * added support for libnl 3.2 and newer * increased initial group key handshake retransmit timeout to 500 ms * added a workaround for 4-way handshake to update SNonce even after having sent EAPOL-Key 3/4 to avoid issues with some supplicant implementations that can change SNonce for each EAP-Key 2/4 * added a workaround for EAPOL-Key 4/4 using incorrect type value in WPA2 mode (some deployed stations use WPA type in that message) * added a WPS workaround for mixed mode AP Settings with Windows 7 * changed WPS AP PIN disabling mechanism to disable the PIN after 10 consecutive failures in addition to using the exponential lockout period * added support for WFA Hotspot 2.0 - GAS/ANQP advertisement of network information - disable_dgaf parameter to disable downstream group-addressed forwarding * simplified licensing terms by selecting the BSD license as the only alternative * EAP-SIM: fixed re-authentication not to update pseudonym * EAP-SIM: use Notification round before EAP-Failure * EAP-AKA: added support for AT_COUNTER_TOO_SMALL * EAP-AKA: skip AKA/Identity exchange if EAP identity is recognized * EAP-AKA': fixed identity for MK derivation * EAP-AKA': updated to RFC 5448 (username prefixes changed); note: this breaks interoperability with older versions * EAP-SIM/AKA: allow pseudonym to be used after unknown reauth id * changed ANonce to be a random number instead of Counter-based * added support for canceling WPS operations with hostapd_cli wps_cancel * fixed EAP/WPS to PSK transition on reassociation in cases where deauthentication is missed * hlr_auc_gw enhancements: - a new command line parameter -u can be used to enable updating of SQN in Milenage file - use 5 bit IND for SQN updates - SQLite database can now be used to store Milenage information * EAP-SIM/AKA DB: added optional use of SQLite database for pseudonyms and reauth data * added support for Chargeable-User-Identity (RFC 4372) * added radius_auth_req_attr and radius_acct_req_attr configuration parameters to allow adding/overriding of RADIUS attributes in Access-Request and Accounting-Request packets * added support for RADIUS dynamic authorization server (RFC 5176) * added initial support for WNM operations - BSS max idle period - WNM-Sleep Mode * added new WPS NFC ctrl_iface mechanism - removed obsoleted WPS_OOB command (including support for deprecated UFD config_method) * added FT support for drivers that implement MLME internally * added SA Query support for drivers that implement MLME internally * removed default ACM=1 from AC_VO and AC_VI * changed VENDOR-TEST EAP method to use proper private enterprise number (this will not interoperate with older versions) * added hostapd.conf parameter vendor_elements to allow arbitrary vendor specific elements to be added to the Beacon and Probe Response frames * added support for configuring GCMP cipher for IEEE 802.11ad * added support for 256-bit AES with internal TLS implementation * changed EAPOL transmission to use AC_VO if WMM is active * fixed EAP-TLS/PEAP/TTLS/FAST server to validate TLS Message Length correctly; invalid messages could have caused the hostapd process to terminate before this fix [CVE-2012-4445] * limit number of active wildcard PINs for WPS Registrar to one to avoid confusing behavior with multiple wildcard PINs * added a workaround for WPS PBC session overlap detection to avoid interop issues with deployed station implementations that do not remove active PBC indication from Probe Request frames properly * added support for using SQLite for the eap_user database * added Acct-Session-Id attribute into Access-Request messages * fixed EAPOL frame transmission to non-QoS STAs with nl80211 (do not send QoS frames if the STA did not negotiate use of QoS for this association) 2012-05-10 - v1.0 * Add channel selection support in hostapd. See hostapd.conf. * Add support for IEEE 802.11v Time Advertisement mechanism with UTC TSF offset. See hostapd.conf for config info. * Delay STA entry removal until Deauth/Disassoc TX status in AP mode. This allows the driver to use PS buffering of Deauthentication and Disassociation frames when the STA is in power save sleep. Only available with drivers that provide TX status events for Deauth/ Disassoc frames (nl80211). * Allow PMKSA caching to be disabled on the Authenticator. See hostap.conf config parameter disable_pmksa_caching. * atheros: Add support for IEEE 802.11w configuration. * bsd: Add support for setting HT values in IFM_MMASK. * Allow client isolation to be configured with ap_isolate. Client isolation can be used to prevent low-level bridging of frames between associated stations in the BSS. By default, this bridging is allowed. * Allow coexistance of HT BSSes with WEP/TKIP BSSes. * Add require_ht config parameter, which can be used to configure hostapd to reject association with any station that does not support HT PHY. * Add support for writing debug log to a file using "-f" option. Also add relog CLI command to re-open the log file. * Add bridge handling for WDS STA interfaces. By default they are added to the configured bridge of the AP interface (if present), but the user can also specify a separate bridge using cli command wds_bridge. * hostapd_cli: - Add wds_bridge command for specifying bridge for WDS STA interfaces. - Add relog command for reopening log file. - Send AP-STA-DISCONNECTED event when an AP disconnects a station due to inactivity. - Add wps_config ctrl_interface command for configuring AP. This command can be used to configure the AP using the internal WPS registrar. It works in the same way as new AP settings received from an ER. - Many WPS/WPS ER commands - see WPS/WPS ER sections for details. - Add command get version, that returns hostapd version string. * WNM: Add BSS Transition Management Request for ESS Disassoc Imminent. Use hostapd_cli ess_disassoc (STA addr) (URL) to send the notification to the STA. * Allow AP mode to disconnect STAs based on low ACK condition (when the data connection is not working properly, e.g., due to the STA going outside the range of the AP). Disabled by default, enable by config option disassoc_low_ack. * Add WPA_IGNORE_CONFIG_ERRORS build option to continue in case of bad config file. * WPS: - Send AP Settings as a wrapped Credential attribute to ctrl_iface in WPS-NEW-AP-SETTINGS. - Dispatch more WPS events through hostapd ctrl_iface. - Add mechanism for indicating non-standard WPS errors. - Change concurrent radio AP to use only one WPS UPnP instance. - Add wps_check_pin command for processing PIN from user input. UIs can use this command to process a PIN entered by a user and to validate the checksum digit (if present). - Add hostap_cli get_config command to display current AP config. - Add new hostapd_cli command, wps_ap_pin, to manage AP PIN at runtime and support dynamic AP PIN management. - Disable AP PIN after 10 consecutive failures. Slow down attacks on failures up to 10. - Allow AP to start in Enrollee mode without AP PIN for probing, to be compatible with Windows 7. - Add Config Error into WPS-FAIL events to provide more info to the user on how to resolve the issue. - When controlling multiple interfaces: - apply WPS commands to all interfaces configured to use WPS - apply WPS config changes to all interfaces that use WPS - when an attack is detected on any interface, disable AP PIN on all interfaces * WPS ER: - Show SetSelectedRegistrar events as ctrl_iface events. - Add special AP Setup Locked mode to allow read only ER. ap_setup_locked=2 can now be used to enable a special mode where WPS ER can learn the current AP settings, but cannot change them. * WPS 2.0: Add support for WPS 2.0 (CONFIG_WPS2) - Add build option CONFIG_WPS_EXTENSIBILITY_TESTING to enable tool for testing protocol extensibility. - Add build option CONFIG_WPS_STRICT to allow disabling of WPS workarounds. - Add support for AuthorizedMACs attribute. * TDLS: - Allow TDLS use or TDLS channel switching in the BSS to be prohibited in the BSS, using config params tdls_prohibit and tdls_prohibit_chan_switch. * EAP server: Add support for configuring fragment size (see fragment_size in hostapd.conf). * wlantest: Add a tool wlantest for IEEE802.11 protocol testing. wlantest can be used to capture frames from a monitor interface for realtime capturing or from pcap files for offline analysis. * Interworking: Support added for 802.11u. Enable in .config with CONFIG_INTERWORKING. See hostapd.conf for config parameters for interworking. * Android: Add build and runtime support for Android hostapd. * Add a new debug message level for excessive information. Use -ddd to enable. * TLS: Add support for tls_disable_time_checks=1 in client mode. * Internal TLS: - Add support for TLS v1.1 (RFC 4346). Enable with build parameter CONFIG_TLSV11. - Add domainComponent parser for X.509 names * Reorder some IEs to get closer to IEEE 802.11 standard. Move WMM into end of Beacon, Probe Resp and (Re)Assoc Resp frames. Move HT IEs to be later in (Re)Assoc Resp. * Many bugfixes.
2013-06-25 02:47:41 +00:00
Some of the files may still include pointers to GPL version 2 license
terms. However, such copyright and license notifications are maintained
only for attribution purposes and any distribution of this software
after February 11, 2012 is no longer under the GPL v2 option.