freebsd-dev/sys/dev/ata/ata-disk.c

613 lines
18 KiB
C
Raw Normal View History

Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
/*-
* Copyright (c) 1998 - 2008 S<EFBFBD>ren Schmidt <sos@FreeBSD.org>
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer,
* without modification, immediately at the beginning of the file.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
* OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
* IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
#include <sys/cdefs.h>
__FBSDID("$FreeBSD$");
#include "opt_ata.h"
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
#include <sys/param.h>
#include <sys/systm.h>
#include <sys/ata.h>
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
#include <sys/kernel.h>
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
#include <sys/module.h>
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
#include <sys/malloc.h>
#include <sys/bio.h>
#include <sys/bus.h>
1999-09-05 15:41:09 +00:00
#include <sys/conf.h>
#include <sys/disk.h>
#include <sys/cons.h>
#include <sys/sema.h>
#include <sys/taskqueue.h>
#include <vm/uma.h>
#include <machine/md_var.h>
#include <machine/bus.h>
#include <sys/rman.h>
#include <geom/geom_disk.h>
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
#include <dev/ata/ata-all.h>
#include <dev/ata/ata-pci.h>
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
#include <dev/ata/ata-disk.h>
#include <dev/ata/ata-raid.h>
#include <dev/pci/pcivar.h>
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
#include <ata_if.h>
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
/* prototypes */
static void ad_init(device_t dev);
static int ad_get_geometry(device_t dev);
static void ad_set_geometry(device_t dev);
static void ad_done(struct ata_request *request);
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
static void ad_describe(device_t dev);
static int ad_version(u_int16_t version);
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
static disk_strategy_t ad_strategy;
static disk_ioctl_t ad_ioctl;
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
static dumper_t ad_dump;
/*
* Most platforms map firmware geom to actual, but some don't. If
* not overridden, default to nothing.
*/
#ifndef ata_disk_firmware_geom_adjust
#define ata_disk_firmware_geom_adjust(disk)
#endif
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
/* local vars */
static MALLOC_DEFINE(M_AD, "ad_driver", "ATA disk driver");
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
static int
ad_probe(device_t dev)
{
struct ata_device *atadev = device_get_softc(dev);
if (!(atadev->param.config & ATA_PROTO_ATAPI) ||
(atadev->param.config == ATA_CFA_MAGIC1) ||
(atadev->param.config == ATA_CFA_MAGIC2) ||
(atadev->param.config == ATA_CFA_MAGIC3))
return 0;
else
return ENXIO;
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
}
static int
ad_attach(device_t dev)
{
struct ata_channel *ch = device_get_softc(device_get_parent(dev));
struct ata_device *atadev = device_get_softc(dev);
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
struct ad_softc *adp;
device_t parent;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
/* check that we have a virgin disk to attach */
if (device_get_ivars(dev))
return EEXIST;
if (!(adp = malloc(sizeof(struct ad_softc), M_AD, M_NOWAIT | M_ZERO))) {
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
device_printf(dev, "out of memory\n");
return ENOMEM;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
}
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
device_set_ivars(dev, adp);
/* get device geometry into internal structs */
if (ad_get_geometry(dev))
return ENXIO;
/* set the max size if configured */
if (ata_setmax)
ad_set_geometry(dev);
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
/* init device parameters */
ad_init(dev);
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
/* announce we are here */
ad_describe(dev);
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
/* create the disk device */
adp->disk = disk_alloc();
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
adp->disk->d_strategy = ad_strategy;
adp->disk->d_ioctl = ad_ioctl;
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
adp->disk->d_dump = ad_dump;
adp->disk->d_name = "ad";
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
adp->disk->d_drv1 = dev;
adp->disk->d_maxsize = ch->dma.max_iosize ? ch->dma.max_iosize : DFLTPHYS;
if (atadev->param.support.command2 & ATA_SUPPORT_ADDRESS48)
adp->disk->d_maxsize = min(adp->disk->d_maxsize, 65536 * DEV_BSIZE);
else /* 28bit ATA command limit */
adp->disk->d_maxsize = min(adp->disk->d_maxsize, 256 * DEV_BSIZE);
adp->disk->d_sectorsize = DEV_BSIZE;
adp->disk->d_mediasize = DEV_BSIZE * (off_t)adp->total_secs;
adp->disk->d_fwsectors = adp->sectors;
adp->disk->d_fwheads = adp->heads;
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
adp->disk->d_unit = device_get_unit(dev);
if (atadev->param.support.command2 & ATA_SUPPORT_FLUSHCACHE)
adp->disk->d_flags |= DISKFLAG_CANFLUSHCACHE;
if ((atadev->param.support.command2 & ATA_SUPPORT_CFA) ||
atadev->param.config == ATA_PROTO_CFA)
adp->disk->d_flags |= DISKFLAG_CANDELETE;
strlcpy(adp->disk->d_ident, atadev->param.serial,
sizeof(adp->disk->d_ident));
parent = device_get_parent(ch->dev);
if (parent != NULL && device_get_parent(parent) != NULL &&
(device_get_devclass(parent) ==
devclass_find("atapci") ||
device_get_devclass(device_get_parent(parent)) ==
devclass_find("pci"))) {
adp->disk->d_hba_vendor = pci_get_vendor(parent);
adp->disk->d_hba_device = pci_get_device(parent);
adp->disk->d_hba_subvendor = pci_get_subvendor(parent);
adp->disk->d_hba_subdevice = pci_get_subdevice(parent);
}
ata_disk_firmware_geom_adjust(adp->disk);
disk_create(adp->disk, DISK_VERSION);
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
device_add_child(dev, "subdisk", device_get_unit(dev));
bus_generic_attach(dev);
callout_init(&atadev->spindown_timer, 1);
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
return 0;
}
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
static int
ad_detach(device_t dev)
{
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
struct ad_softc *adp = device_get_ivars(dev);
struct ata_device *atadev = device_get_softc(dev);
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
device_t *children;
int nchildren, i;
/* check that we have a valid disk to detach */
if (!device_get_ivars(dev))
return ENXIO;
/* destroy the power timeout */
callout_drain(&atadev->spindown_timer);
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
/* detach & delete all children */
if (!device_get_children(dev, &children, &nchildren)) {
for (i = 0; i < nchildren; i++)
if (children[i])
device_delete_child(dev, children[i]);
free(children, M_TEMP);
}
/* destroy disk from the system so we don't get any further requests */
disk_destroy(adp->disk);
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
/* fail requests on the queue and any that's "in flight" for this device */
ata_fail_requests(dev);
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
/* don't leave anything behind */
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
device_set_ivars(dev, NULL);
free(adp, M_AD);
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
return 0;
}
static int
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
ad_shutdown(device_t dev)
{
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
struct ata_device *atadev = device_get_softc(dev);
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
if (atadev->param.support.command2 & ATA_SUPPORT_FLUSHCACHE)
ata_controlcmd(dev, ATA_FLUSHCACHE, 0, 0, 0);
return 0;
}
static int
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
ad_reinit(device_t dev)
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
{
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
struct ata_channel *ch = device_get_softc(device_get_parent(dev));
struct ata_device *atadev = device_get_softc(dev);
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
/* if detach pending, return error */
if (!(ch->devices & (ATA_ATA_MASTER << atadev->unit)))
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
return 1;
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
ad_init(dev);
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
return 0;
}
static void
ad_power_callback(struct ata_request *request)
{
device_printf(request->dev, "drive spun down.\n");
ata_free_request(request);
}
static void
ad_spindown(void *priv)
{
device_t dev = priv;
struct ata_device *atadev = device_get_softc(dev);
struct ata_request *request;
if (!atadev->spindown)
return;
device_printf(dev, "Idle, spin down\n");
atadev->spindown_state = 1;
if (!(request = ata_alloc_request())) {
device_printf(dev, "FAILURE - out of memory in ad_spindown\n");
return;
}
request->dev = dev;
request->flags = ATA_R_CONTROL;
request->timeout = ATA_REQUEST_TIMEOUT;
request->retries = 1;
request->callback = ad_power_callback;
request->u.ata.command = ATA_STANDBY_IMMEDIATE;
ata_queue_request(request);
}
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
static void
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
ad_strategy(struct bio *bp)
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
{
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
device_t dev = bp->bio_disk->d_drv1;
struct ata_device *atadev = device_get_softc(dev);
struct ata_request *request;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
if (atadev->spindown)
callout_reset(&atadev->spindown_timer, hz * atadev->spindown,
ad_spindown, dev);
if (!(request = ata_alloc_request())) {
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
device_printf(dev, "FAILURE - out of memory in start\n");
biofinish(bp, NULL, ENOMEM);
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
return;
}
/* setup request */
request->dev = dev;
request->bio = bp;
request->callback = ad_done;
if (atadev->spindown_state) {
device_printf(dev, "request while spun down, starting.\n");
atadev->spindown_state = 0;
request->timeout = MAX(ATA_REQUEST_TIMEOUT, 31);
}
else {
request->timeout = ATA_REQUEST_TIMEOUT;
}
request->retries = 2;
request->data = bp->bio_data;
request->bytecount = bp->bio_bcount;
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
request->u.ata.lba = bp->bio_pblkno;
request->u.ata.count = request->bytecount / DEV_BSIZE;
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
request->transfersize = min(bp->bio_bcount, atadev->max_iosize);
switch (bp->bio_cmd) {
case BIO_READ:
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
request->flags = ATA_R_READ;
if (atadev->mode >= ATA_DMA) {
request->u.ata.command = ATA_READ_DMA;
request->flags |= ATA_R_DMA;
}
else if (request->transfersize > DEV_BSIZE)
request->u.ata.command = ATA_READ_MUL;
else
request->u.ata.command = ATA_READ;
break;
case BIO_WRITE:
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
request->flags = ATA_R_WRITE;
if (atadev->mode >= ATA_DMA) {
request->u.ata.command = ATA_WRITE_DMA;
request->flags |= ATA_R_DMA;
}
else if (request->transfersize > DEV_BSIZE)
request->u.ata.command = ATA_WRITE_MUL;
else
request->u.ata.command = ATA_WRITE;
break;
case BIO_DELETE:
request->flags = ATA_R_CONTROL;
request->u.ata.command = ATA_CFA_ERASE;
request->transfersize = 0;
request->donecount = bp->bio_bcount;
break;
case BIO_FLUSH:
request->u.ata.lba = 0;
request->u.ata.count = 0;
request->u.ata.feature = 0;
request->bytecount = 0;
request->transfersize = 0;
request->flags = ATA_R_CONTROL;
request->u.ata.command = ATA_FLUSHCACHE;
break;
default:
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
device_printf(dev, "FAILURE - unknown BIO operation\n");
ata_free_request(request);
biofinish(bp, NULL, EIO);
return;
}
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
request->flags |= ATA_R_ORDERED;
ata_queue_request(request);
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
}
static void
ad_done(struct ata_request *request)
{
struct bio *bp = request->bio;
/* finish up transfer */
if ((bp->bio_error = request->result))
bp->bio_flags |= BIO_ERROR;
bp->bio_resid = bp->bio_bcount - request->donecount;
biodone(bp);
ata_free_request(request);
}
static int
ad_ioctl(struct disk *disk, u_long cmd, void *data, int flag, struct thread *td)
{
return ata_device_ioctl(disk->d_drv1, cmd, data);
}
static int
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
ad_dump(void *arg, void *virtual, vm_offset_t physical,
off_t offset, size_t length)
{
struct disk *dp = arg;
device_t dev = dp->d_drv1;
struct bio bp;
/* XXX: Drop pre-dump request queue. Long request queue processing
* causes stack overflow in ATA working in dumping (interruptless) mode.
* Conter-XXX: To make dump coherent we should avoid doing anything
* else while dumping.
*/
ata_drop_requests(dev);
/* length zero is special and really means flush buffers to media */
if (!length) {
struct ata_device *atadev = device_get_softc(dev);
int error = 0;
if (atadev->param.support.command2 & ATA_SUPPORT_FLUSHCACHE)
error = ata_controlcmd(dev, ATA_FLUSHCACHE, 0, 0, 0);
return error;
}
bzero(&bp, sizeof(struct bio));
bp.bio_disk = dp;
bp.bio_pblkno = offset / DEV_BSIZE;
bp.bio_bcount = length;
bp.bio_data = virtual;
bp.bio_cmd = BIO_WRITE;
ad_strategy(&bp);
return bp.bio_error;
}
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
static void
ad_init(device_t dev)
{
struct ata_device *atadev = device_get_softc(dev);
ata_setmode(dev);
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
/* enable readahead caching */
if (atadev->param.support.command1 & ATA_SUPPORT_LOOKAHEAD)
ata_controlcmd(dev, ATA_SETFEATURES, ATA_SF_ENAB_RCACHE, 0, 0);
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
/* enable write caching if supported and configured */
if (atadev->param.support.command1 & ATA_SUPPORT_WRITECACHE) {
if (ata_wc)
ata_controlcmd(dev, ATA_SETFEATURES, ATA_SF_ENAB_WCACHE, 0, 0);
else
ata_controlcmd(dev, ATA_SETFEATURES, ATA_SF_DIS_WCACHE, 0, 0);
}
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
/* use multiple sectors/interrupt if device supports it */
if (ad_version(atadev->param.version_major)) {
int secsperint = max(1, min(atadev->param.sectors_intr & 0xff, 16));
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
if (!ata_controlcmd(dev, ATA_SET_MULTI, 0, 0, secsperint))
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
atadev->max_iosize = secsperint * DEV_BSIZE;
else
atadev->max_iosize = DEV_BSIZE;
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
}
else
atadev->max_iosize = DEV_BSIZE;
}
static int
ad_get_geometry(device_t dev)
{
struct ata_device *atadev = device_get_softc(dev);
struct ad_softc *adp = device_get_ivars(dev);
u_int64_t lbasize48;
u_int32_t lbasize;
if ((atadev->param.atavalid & ATA_FLAG_54_58) &&
atadev->param.current_heads && atadev->param.current_sectors) {
adp->heads = atadev->param.current_heads;
adp->sectors = atadev->param.current_sectors;
adp->total_secs = (u_int32_t)atadev->param.current_size_1 |
((u_int32_t)atadev->param.current_size_2 << 16);
}
else {
adp->heads = atadev->param.heads;
adp->sectors = atadev->param.sectors;
adp->total_secs = atadev->param.cylinders * adp->heads * adp->sectors;
}
lbasize = (u_int32_t)atadev->param.lba_size_1 |
((u_int32_t)atadev->param.lba_size_2 << 16);
/* This device exists, but has no size. Filter out this bogus device. */
if (!lbasize && !adp->total_secs)
return ENXIO;
/* does this device need oldstyle CHS addressing */
if (!ad_version(atadev->param.version_major) || !lbasize)
atadev->flags |= ATA_D_USE_CHS;
/* use the 28bit LBA size if valid or bigger than the CHS mapping */
if (atadev->param.cylinders == 16383 || adp->total_secs < lbasize)
adp->total_secs = lbasize;
/* use the 48bit LBA size if valid */
lbasize48 = ((u_int64_t)atadev->param.lba_size48_1) |
((u_int64_t)atadev->param.lba_size48_2 << 16) |
((u_int64_t)atadev->param.lba_size48_3 << 32) |
((u_int64_t)atadev->param.lba_size48_4 << 48);
if ((atadev->param.support.command2 & ATA_SUPPORT_ADDRESS48) &&
lbasize48 > ATA_MAX_28BIT_LBA)
adp->total_secs = lbasize48;
return 0;
}
static void
ad_set_geometry(device_t dev)
{
struct ad_softc *adp = device_get_ivars(dev);
struct ata_request *request;
if (1 | bootverbose)
device_printf(dev, "ORG %ju sectors [%juC/%dH/%dS]\n", adp->total_secs,
adp->total_secs / (adp->heads * adp->sectors),
adp->heads, adp->sectors);
if (!(request = ata_alloc_request()))
return;
/* get the max native size the device supports */
request->dev = dev;
request->u.ata.command = ATA_READ_NATIVE_MAX_ADDRESS;
request->u.ata.lba = 0;
request->u.ata.count = 0;
request->u.ata.feature = 0;
request->flags = ATA_R_CONTROL | ATA_R_QUIET;
request->timeout = ATA_REQUEST_TIMEOUT;
request->retries = 0;
ata_queue_request(request);
if (request->status & ATA_S_ERROR)
goto out;
if (1 | bootverbose)
device_printf(dev, "MAX %ju sectors\n", request->u.ata.lba + 1);
/* if original size equals max size nothing more todo */
if (adp->total_secs >= request->u.ata.lba)
goto out;
/* set the max native size to its max */
request->dev = dev;
request->u.ata.command = ATA_SET_MAX_ADDRESS;
request->u.ata.count = 1;
request->u.ata.feature = 0;
request->flags = ATA_R_CONTROL;
request->timeout = ATA_REQUEST_TIMEOUT;
request->retries = 0;
ata_queue_request(request);
if (request->status & ATA_S_ERROR)
goto out;
/* refresh geometry from drive */
ata_getparam(device_get_softc(dev), 0);
ad_get_geometry(dev);
if (1 | bootverbose)
device_printf(dev, "NEW %ju sectors [%juC/%dH/%dS]\n", adp->total_secs,
adp->total_secs / (adp->heads * adp->sectors),
adp->heads, adp->sectors);
out:
ata_free_request(request);
}
static void
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
ad_describe(device_t dev)
{
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
struct ata_channel *ch = device_get_softc(device_get_parent(dev));
struct ata_device *atadev = device_get_softc(dev);
struct ad_softc *adp = device_get_ivars(dev);
u_int8_t *marker, vendor[64], product[64];
/* try to separate the ATA model string into vendor and model parts */
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
if ((marker = index(atadev->param.model, ' ')) ||
(marker = index(atadev->param.model, '-'))) {
int len = (marker - atadev->param.model);
strncpy(vendor, atadev->param.model, len);
vendor[len++] = 0;
strcat(vendor, " ");
strncpy(product, atadev->param.model + len, 40 - len);
vendor[40 - len] = 0;
}
else {
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
if (!strncmp(atadev->param.model, "ST", 2))
strcpy(vendor, "Seagate ");
else if (!strncmp(atadev->param.model, "HDS", 3))
strcpy(vendor, "Hitachi ");
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
else
strcpy(vendor, "");
strncpy(product, atadev->param.model, 40);
}
device_printf(dev, "%juMB <%s%s %.8s> at ata%d-%s %s%s %s\n",
adp->total_secs / (1048576 / DEV_BSIZE),
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
vendor, product, atadev->param.revision,
device_get_unit(ch->dev), ata_unit2str(atadev),
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
(adp->flags & AD_F_TAG_ENABLED) ? "tagged " : "",
ata_mode2str(atadev->mode),
ata_satarev2str(ATA_GETREV(device_get_parent(dev), atadev->unit)));
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
if (bootverbose) {
device_printf(dev, "%ju sectors [%juC/%dH/%dS] "
"%d sectors/interrupt %d depth queue\n", adp->total_secs,
adp->total_secs / (adp->heads * adp->sectors),
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
adp->heads, adp->sectors, atadev->max_iosize / DEV_BSIZE,
adp->num_tags + 1);
}
}
static int
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
ad_version(u_int16_t version)
{
int bit;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
if (version == 0xffff)
return 0;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
for (bit = 15; bit >= 0; bit--)
if (version & (1<<bit))
return bit;
return 0;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
}
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
static device_method_t ad_methods[] = {
/* device interface */
DEVMETHOD(device_probe, ad_probe),
DEVMETHOD(device_attach, ad_attach),
DEVMETHOD(device_detach, ad_detach),
DEVMETHOD(device_shutdown, ad_shutdown),
/* ATA methods */
DEVMETHOD(ata_reinit, ad_reinit),
{ 0, 0 }
};
static driver_t ad_driver = {
"ad",
ad_methods,
0,
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
};
devclass_t ad_devclass;
DRIVER_MODULE(ad, ata, ad_driver, ad_devclass, NULL, NULL);
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
MODULE_VERSION(ad, 1);
MODULE_DEPEND(ad, ata, 1, 1, 1);