freebsd-dev/sys/dev/usb/serial/uftdi_reg.h

/*	$NetBSD: uftdireg.h,v 1.6 2002/07/11 21:14:28 augustss Exp $ */
/*	$FreeBSD$	*/

/*
 * Definitions for the FTDI USB Single Port Serial Converter -
 * known as FTDI_SIO (Serial Input/Output application of the chipset)
 *
 * The device is based on the FTDI FT8U100AX chip. It has a DB25 on one side,
 * USB on the other.
 *
 * Thanx to FTDI (http://www.ftdi.co.uk) for so kindly providing details
 * of the protocol required to talk to the device and ongoing assistence
 * during development.
 *
 * Bill Ryder - bryder@sgi.com of Silicon Graphics, Inc. is the original
 * author of this file.
 */
/* Modified by Lennart Augustsson */

/* Vendor Request Interface */
#define	FTDI_SIO_RESET 		0	/* Reset the port */
#define	FTDI_SIO_MODEM_CTRL 	1	/* Set the modem control register */
#define	FTDI_SIO_SET_FLOW_CTRL	2	/* Set flow control register */
#define	FTDI_SIO_SET_BAUD_RATE	3	/* Set baud rate */
#define	FTDI_SIO_SET_DATA	4	/* Set the data characteristics of the
					 * port */
#define	FTDI_SIO_GET_STATUS	5	/* Retrieve current value of status
					 * reg */
#define	FTDI_SIO_SET_EVENT_CHAR	6	/* Set the event character */
#define	FTDI_SIO_SET_ERROR_CHAR	7	/* Set the error character */
#define	FTDI_SIO_SET_LATENCY	9	/* Set the latency timer */
#define	FTDI_SIO_GET_LATENCY	10	/* Read the latency timer */
#define	FTDI_SIO_SET_BITMODE	11	/* Set the bit bang I/O mode */
#define	FTDI_SIO_GET_BITMODE	12	/* Read pin states from any mode */
#define	FTDI_SIO_READ_EEPROM	144	/* Read eeprom word */
#define	FTDI_SIO_WRITE_EEPROM	145	/* Write eeprom word */
#define	FTDI_SIO_ERASE_EEPROM	146	/* Erase entire eeprom */

/* Port Identifier Table */
#define	FTDI_PIT_DEFAULT 	0	/* SIOA */
#define	FTDI_PIT_SIOA		1	/* SIOA */
#define	FTDI_PIT_SIOB		2	/* SIOB */
#define	FTDI_PIT_PARALLEL	3	/* Parallel */

/* Values for driver_info */
#define	UFTDI_JTAG_IFACE(i)	(1 << i)	/* Flag interface as jtag */
#define	UFTDI_JTAG_IFACES_MAX	8		/* Allow up to 8 jtag intfs */
#define	UFTDI_JTAG_CHECK_STRING	0xff		/* Check product names table */
#define	UFTDI_JTAG_MASK		0xff

/*
 * BmRequestType:  0100 0000B
 * bRequest:       FTDI_SIO_RESET
 * wValue:         Control Value
 *                   0 = Reset SIO
 *                   1 = Purge RX buffer
 *                   2 = Purge TX buffer
 * wIndex:         Port
 * wLength:        0
 * Data:           None
 *
 * The Reset SIO command has this effect:
 *
 *    Sets flow control set to 'none'
 *    Event char = 0x0d
 *    Event trigger = disabled
 *    Purge RX buffer
 *    Purge TX buffer
 *    Clear DTR
 *    Clear RTS
 *    baud and data format not reset
 *
 * The Purge RX and TX buffer commands affect nothing except the buffers
 */
/* FTDI_SIO_RESET */
#define	FTDI_SIO_RESET_SIO 0
#define	FTDI_SIO_RESET_PURGE_RX 1
#define	FTDI_SIO_RESET_PURGE_TX 2

/*
 * BmRequestType:  0100 0000B
 * bRequest:       FTDI_SIO_SET_BAUDRATE
 * wValue:         BaudRate low bits
 * wIndex:         Port and BaudRate high bits 
 * wLength:        0
 * Data:           None
 */
/* FTDI_SIO_SET_BAUDRATE */

/*
 * BmRequestType:  0100 0000B
 * bRequest:       FTDI_SIO_SET_DATA
 * wValue:         Data characteristics (see below)
 * wIndex:         Port
 * wLength:        0
 * Data:           No
 *
 * Data characteristics
 *
 *   B0..7   Number of data bits
 *   B8..10  Parity
 *           0 = None
 *           1 = Odd
 *           2 = Even
 *           3 = Mark
 *           4 = Space
 *   B11..13 Stop Bits
 *           0 = 1
 *           1 = 1.5
 *           2 = 2
 *   B14..15 Reserved
 *
 */
/* FTDI_SIO_SET_DATA */
#define	FTDI_SIO_SET_DATA_BITS(n) (n)
#define	FTDI_SIO_SET_DATA_PARITY_NONE (0x0 << 8)
#define	FTDI_SIO_SET_DATA_PARITY_ODD (0x1 << 8)
#define	FTDI_SIO_SET_DATA_PARITY_EVEN (0x2 << 8)
#define	FTDI_SIO_SET_DATA_PARITY_MARK (0x3 << 8)
#define	FTDI_SIO_SET_DATA_PARITY_SPACE (0x4 << 8)
#define	FTDI_SIO_SET_DATA_STOP_BITS_1 (0x0 << 11)
#define	FTDI_SIO_SET_DATA_STOP_BITS_15 (0x1 << 11)
#define	FTDI_SIO_SET_DATA_STOP_BITS_2 (0x2 << 11)
#define	FTDI_SIO_SET_BREAK (0x1 << 14)

/*
 * BmRequestType:   0100 0000B
 * bRequest:        FTDI_SIO_MODEM_CTRL
 * wValue:          ControlValue (see below)
 * wIndex:          Port
 * wLength:         0
 * Data:            None
 *
 * NOTE: If the device is in RTS/CTS flow control, the RTS set by this
 * command will be IGNORED without an error being returned
 * Also - you can not set DTR and RTS with one control message
 *
 * ControlValue
 * B0    DTR state
 *          0 = reset
 *          1 = set
 * B1    RTS state
 *          0 = reset
 *          1 = set
 * B2..7 Reserved
 * B8    DTR state enable
 *          0 = ignore
 *          1 = use DTR state
 * B9    RTS state enable
 *          0 = ignore
 *          1 = use RTS state
 * B10..15 Reserved
 */
/* FTDI_SIO_MODEM_CTRL */
#define	FTDI_SIO_SET_DTR_MASK 0x1
#define	FTDI_SIO_SET_DTR_HIGH (1 | ( FTDI_SIO_SET_DTR_MASK  << 8))
#define	FTDI_SIO_SET_DTR_LOW  (0 | ( FTDI_SIO_SET_DTR_MASK  << 8))
#define	FTDI_SIO_SET_RTS_MASK 0x2
#define	FTDI_SIO_SET_RTS_HIGH (2 | ( FTDI_SIO_SET_RTS_MASK << 8))
#define	FTDI_SIO_SET_RTS_LOW (0 | ( FTDI_SIO_SET_RTS_MASK << 8))

/*
 *   BmRequestType:  0100 0000b
 *   bRequest:       FTDI_SIO_SET_FLOW_CTRL
 *   wValue:         Xoff/Xon
 *   wIndex:         Protocol/Port - hIndex is protocol / lIndex is port
 *   wLength:        0
 *   Data:           None
 *
 * hIndex protocol is:
 *   B0 Output handshaking using RTS/CTS
 *       0 = disabled
 *       1 = enabled
 *   B1 Output handshaking using DTR/DSR
 *       0 = disabled
 *       1 = enabled
 *   B2 Xon/Xoff handshaking
 *       0 = disabled
 *       1 = enabled
 *
 * A value of zero in the hIndex field disables handshaking
 *
 * If Xon/Xoff handshaking is specified, the hValue field should contain the
 * XOFF character and the lValue field contains the XON character.
 */
/* FTDI_SIO_SET_FLOW_CTRL */
#define	FTDI_SIO_DISABLE_FLOW_CTRL 0x0
#define	FTDI_SIO_RTS_CTS_HS 0x1
#define	FTDI_SIO_DTR_DSR_HS 0x2
#define	FTDI_SIO_XON_XOFF_HS 0x4

/*
 *  BmRequestType:   0100 0000b
 *  bRequest:        FTDI_SIO_SET_EVENT_CHAR
 *  wValue:          Event Char
 *  wIndex:          Port
 *  wLength:         0
 *  Data:            None
 *
 * wValue:
 *   B0..7   Event Character
 *   B8      Event Character Processing
 *             0 = disabled
 *             1 = enabled
 *   B9..15  Reserved
 *
 * FTDI_SIO_SET_EVENT_CHAR
 *
 * Set the special event character for the specified communications port.
 * If the device sees this character it will immediately return the
 * data read so far - rather than wait 40ms or until 62 bytes are read
 * which is what normally happens.
 */

/*
 *  BmRequestType:  0100 0000b
 *  bRequest:       FTDI_SIO_SET_ERROR_CHAR
 *  wValue:         Error Char
 *  wIndex:         Port
 *  wLength:        0
 *  Data:           None
 *
 *  Error Char
 *  B0..7  Error Character
 *  B8     Error Character Processing
 *           0 = disabled
 *           1 = enabled
 *  B9..15 Reserved
 * FTDI_SIO_SET_ERROR_CHAR
 * Set the parity error replacement character for the specified communications
 * port.
 */

/*
 *   BmRequestType:   1100 0000b
 *   bRequest:        FTDI_SIO_GET_MODEM_STATUS
 *   wValue:          zero
 *   wIndex:          Port
 *   wLength:         1
 *   Data:            Status
 *
 * One byte of data is returned
 * B0..3 0
 * B4    CTS
 *         0 = inactive
 *         1 = active
 * B5    DSR
 *         0 = inactive
 *         1 = active
 * B6    Ring Indicator (RI)
 *         0 = inactive
 *         1 = active
 * B7    Receive Line Signal Detect (RLSD)
 *         0 = inactive
 *         1 = active
 *
 * FTDI_SIO_GET_MODEM_STATUS
 * Retrieve the current value of the modem status register.
 */
#define	FTDI_SIO_CTS_MASK 0x10
#define	FTDI_SIO_DSR_MASK 0x20
#define	FTDI_SIO_RI_MASK  0x40
#define	FTDI_SIO_RLSD_MASK 0x80

/*
 * DATA FORMAT
 *
 * IN Endpoint
 *
 * The device reserves the first two bytes of data on this endpoint to contain
 * the current values of the modem and line status registers. In the absence of
 * data, the device generates a message consisting of these two status bytes
 * every 40 ms.
 *
 * Byte 0: Modem Status
 *   NOTE: 4 upper bits have same layout as the MSR register in a 16550
 *
 * Offset	Description
 * B0..3	Port
 * B4		Clear to Send (CTS)
 * B5		Data Set Ready (DSR)
 * B6		Ring Indicator (RI)
 * B7		Receive Line Signal Detect (RLSD)
 *
 * Byte 1: Line Status
 *   NOTE: same layout as the LSR register in a 16550
 *
 * Offset	Description
 * B0	Data Ready (DR)
 * B1	Overrun Error (OE)
 * B2	Parity Error (PE)
 * B3	Framing Error (FE)
 * B4	Break Interrupt (BI)
 * B5	Transmitter Holding Register (THRE)
 * B6	Transmitter Empty (TEMT)
 * B7	Error in RCVR FIFO
 * OUT Endpoint
 *
 * This device reserves the first bytes of data on this endpoint contain the
 * length and port identifier of the message. For the FTDI USB Serial converter
 * the port identifier is always 1.
 *
 * Byte 0: Port & length
 *
 * Offset	Description
 * B0..1	Port
 * B2..7	Length of message - (not including Byte 0)
 */
#define	FTDI_PORT_MASK 0x0f
#define	FTDI_MSR_MASK 0xf0
#define	FTDI_GET_MSR(p) (((p)[0]) & FTDI_MSR_MASK)
#define	FTDI_GET_LSR(p) ((p)[1])
#define	FTDI_LSR_MASK (~0x60)		/* interesting bits */
#define	FTDI_OUT_TAG(len, port) (((len) << 2) | (port))