- Remove the redundant device disabled hint handling; ever since

r241119 that's performed globally by device_attach(9).
- As for the EM-class of devices, em(4) supports multiple queues
  and MSI-X respectively only with 82574 devices. However, since
  the conversion to iflib(4), em(4) relies on the interrupt type
  fallback mechanism, i. e. MSI-X -> MSI -> INTx, of iflib(4) to
  figure out the interrupt type to use for the EM-class (as well
  as the IGB-class) of MACs. Moreover, despite the datasheet for
  82583V not mentioning any support of MSI-X, there actually are
  82583V devices out there that report a varying number of MSI-X
  messages as supported. The interrupt type fallback of iflib(4)
  is causing two failure modes depending on the actual number of
  MSI-X messages supported for such instances of 82583V:
  1) With only one MSI-X message supported, none is left for the
     RX/TX queues as that one message gets assigned to the admin
     interrupt. Worse, later on - which will be addressed with a
     separate fix - iflib(4) interprets that one messages as MSI
     or INTx to be set up, but fails to actually do so as it has
     previously called pci_alloc_msix(9). [1, 2]
  2) With more message supported, their distribution is okay but
     then em_if_msix_intr_assign() doesn't work for 82583V, with
     the interface being left in a non-working state, too. [3]
  Thus, let em_if_attach_pre() indicate to iflib(4) to try MSI-X
  with 82574 only, and at most MSI for the remainder of EM-class
  devices.
  While at it, remove "try_second_bar" as it's polarity inverted
  and not actually needed.
- Remove code from em_if_timer() that effectively is a NOP since
  the conversion to iflib(4) ("trigger" is no longer read).
  While at it, let the comment for em_if_timer() reflect reality
  after said conversion.
- Implement an ifdi_watchdog_reset method which only updates the
  em(4) "watchdog_events" counter but doesn't perform any reset,
  so that the em(4) "watchdog_timeouts" SYSCTL (iflib(4) doesn't
  provide a counterpart) reflects reality and these timeouts add
  to IFCOUNTER_OERRORS again after the iflib(4) conversion.
- Remove the "mbuf_defrag_fail" and "tx_dma_fail" SYSCTLS; since
  the iflib(4) conversion, associated counters are disconnected,
  but iflib(4) provides "mbuf_defrag_failed" and "tx_map_failed"
  respectively as equivalents.
- Move the description preceding lem_smartspeed() to the correct
  spot before em_reset() and bring back appropriate comments for
  {igb,em}_initialize_rss_mapping() and lem_smartspeed() lost in
  the iflib(4) conversion.
- Adapt some other function descriptions and INIT_DEBUGOUT() use
  to match reality after the iflib(4) conversion.
- Put the debugging message of em_enable_vectors_82574() (missed
  in r343578) under bootverbose, too.

PR:		219428 [1], 235246 [2], 235147 [3]
Reviewed by:	erj (previous version)
Differential Revision:	https://reviews.freebsd.org/D19108
This commit is contained in:
Marius Strobl 2019-02-09 11:58:40 +00:00
parent c68d0f8b3d
commit 6143b97764
Notes: svn2git 2020-12-20 02:59:44 +00:00
svn path=/head/; revision=343934
2 changed files with 50 additions and 55 deletions

View File

@ -249,6 +249,7 @@ static int em_if_mtu_set(if_ctx_t ctx, uint32_t mtu);
static void em_if_timer(if_ctx_t ctx, uint16_t qid);
static void em_if_vlan_register(if_ctx_t ctx, u16 vtag);
static void em_if_vlan_unregister(if_ctx_t ctx, u16 vtag);
static void em_if_watchdog_reset(if_ctx_t ctx);
static void em_identify_hardware(if_ctx_t ctx);
static int em_allocate_pci_resources(if_ctx_t ctx);
@ -386,6 +387,7 @@ static device_method_t em_if_methods[] = {
DEVMETHOD(ifdi_mtu_set, em_if_mtu_set),
DEVMETHOD(ifdi_promisc_set, em_if_set_promisc),
DEVMETHOD(ifdi_timer, em_if_timer),
DEVMETHOD(ifdi_watchdog_reset, em_if_watchdog_reset),
DEVMETHOD(ifdi_vlan_register, em_if_vlan_register),
DEVMETHOD(ifdi_vlan_unregister, em_if_vlan_unregister),
DEVMETHOD(ifdi_get_counter, em_if_get_counter),
@ -721,7 +723,6 @@ em_set_num_queues(if_ctx_t ctx)
*
* return 0 on success, positive on failure
*********************************************************************/
static int
em_if_attach_pre(if_ctx_t ctx)
{
@ -731,15 +732,10 @@ em_if_attach_pre(if_ctx_t ctx)
struct e1000_hw *hw;
int error = 0;
INIT_DEBUGOUT("em_if_attach_pre begin");
INIT_DEBUGOUT("em_if_attach_pre: begin");
dev = iflib_get_dev(ctx);
adapter = iflib_get_softc(ctx);
if (resource_disabled("em", device_get_unit(dev))) {
device_printf(dev, "Disabled by device hint\n");
return (ENXIO);
}
adapter->ctx = adapter->osdep.ctx = ctx;
adapter->dev = adapter->osdep.dev = dev;
scctx = adapter->shared = iflib_get_softc_ctx(ctx);
@ -777,7 +773,6 @@ em_if_attach_pre(if_ctx_t ctx)
/* Determine hardware and mac info */
em_identify_hardware(ctx);
scctx->isc_msix_bar = PCIR_BAR(EM_MSIX_BAR);
scctx->isc_tx_nsegments = EM_MAX_SCATTER;
scctx->isc_nrxqsets_max = scctx->isc_ntxqsets_max = em_set_num_queues(ctx);
if (bootverbose)
@ -785,8 +780,6 @@ em_if_attach_pre(if_ctx_t ctx)
scctx->isc_ntxqsets_max);
if (adapter->hw.mac.type >= igb_mac_min) {
int try_second_bar;
scctx->isc_txqsizes[0] = roundup2(scctx->isc_ntxd[0] * sizeof(union e1000_adv_tx_desc), EM_DBA_ALIGN);
scctx->isc_rxqsizes[0] = roundup2(scctx->isc_nrxd[0] * sizeof(union e1000_adv_rx_desc), EM_DBA_ALIGN);
scctx->isc_txd_size[0] = sizeof(union e1000_adv_tx_desc);
@ -800,14 +793,13 @@ em_if_attach_pre(if_ctx_t ctx)
CSUM_IP6_TCP | CSUM_IP6_UDP;
if (adapter->hw.mac.type != e1000_82575)
scctx->isc_tx_csum_flags |= CSUM_SCTP | CSUM_IP6_SCTP;
/*
** Some new devices, as with ixgbe, now may
** use a different BAR, so we need to keep
** track of which is used.
*/
try_second_bar = pci_read_config(dev, scctx->isc_msix_bar, 4);
if (try_second_bar == 0)
scctx->isc_msix_bar = PCIR_BAR(EM_MSIX_BAR);
if (pci_read_config(dev, scctx->isc_msix_bar, 4) == 0)
scctx->isc_msix_bar += 4;
} else if (adapter->hw.mac.type >= em_mac_min) {
scctx->isc_txqsizes[0] = roundup2(scctx->isc_ntxd[0]* sizeof(struct e1000_tx_desc), EM_DBA_ALIGN);
@ -837,6 +829,16 @@ em_if_attach_pre(if_ctx_t ctx)
*/
scctx->isc_capenable &= ~(IFCAP_TSO4 | IFCAP_VLAN_HWTSO);
scctx->isc_tx_csum_flags = CSUM_TCP | CSUM_UDP | CSUM_IP_TSO;
/*
* We support MSI-X with 82574 only, but indicate to iflib(4)
* that it shall give MSI at least a try with other devices.
*/
if (adapter->hw.mac.type == e1000_82574) {
scctx->isc_msix_bar = PCIR_BAR(EM_MSIX_BAR);
} else {
scctx->isc_msix_bar = -1;
scctx->isc_disable_msix = 1;
}
} else {
scctx->isc_txqsizes[0] = roundup2((scctx->isc_ntxd[0] + 1) * sizeof(struct e1000_tx_desc), EM_DBA_ALIGN);
scctx->isc_rxqsizes[0] = roundup2((scctx->isc_nrxd[0] + 1) * sizeof(struct e1000_rx_desc), EM_DBA_ALIGN);
@ -847,6 +849,7 @@ em_if_attach_pre(if_ctx_t ctx)
scctx->isc_capabilities = scctx->isc_capenable = LEM_CAPS;
if (adapter->hw.mac.type < e1000_82543)
scctx->isc_capenable &= ~(IFCAP_HWCSUM|IFCAP_VLAN_HWCSUM);
/* INTx only */
scctx->isc_msix_bar = 0;
}
@ -1092,13 +1095,12 @@ em_if_attach_post(if_ctx_t ctx)
*
* return 0 on success, positive on failure
*********************************************************************/
static int
em_if_detach(if_ctx_t ctx)
{
struct adapter *adapter = iflib_get_softc(ctx);
INIT_DEBUGOUT("em_detach: begin");
INIT_DEBUGOUT("em_if_detach: begin");
e1000_phy_hw_reset(&adapter->hw);
@ -1203,9 +1205,7 @@ em_if_mtu_set(if_ctx_t ctx, uint32_t mtu)
* by the driver as a hw/sw initialization routine to get to a
* consistent state.
*
* return 0 on success, positive on failure
**********************************************************************/
static void
em_if_init(if_ctx_t ctx)
{
@ -1214,6 +1214,7 @@ em_if_init(if_ctx_t ctx)
struct ifnet *ifp = iflib_get_ifp(ctx);
struct em_tx_queue *tx_que;
int i;
INIT_DEBUGOUT("em_if_init: begin");
/* Get the latest mac address, User can use a LAA */
@ -1697,37 +1698,24 @@ em_if_multi_set(if_ctx_t ctx)
}
}
/*********************************************************************
* Timer routine
*
* This routine checks for link status and updates statistics.
* This routine schedules em_if_update_admin_status() to check for
* link status and to gather statistics as well as to perform some
* controller-specific hardware patting.
*
**********************************************************************/
static void
em_if_timer(if_ctx_t ctx, uint16_t qid)
{
struct adapter *adapter = iflib_get_softc(ctx);
struct em_rx_queue *que;
int i;
int trigger = 0;
if (qid != 0)
return;
iflib_admin_intr_deferred(ctx);
/* Mask to use in the irq trigger */
if (adapter->intr_type == IFLIB_INTR_MSIX) {
for (i = 0, que = adapter->rx_queues; i < adapter->rx_num_queues; i++, que++)
trigger |= que->eims;
} else {
trigger = E1000_ICS_RXDMT0;
}
}
static void
em_if_update_admin_status(if_ctx_t ctx)
{
@ -1833,21 +1821,30 @@ em_if_update_admin_status(if_ctx_t ctx)
E1000_WRITE_REG(&adapter->hw, E1000_IMS, EM_MSIX_LINK | E1000_IMS_LSC);
}
static void
em_if_watchdog_reset(if_ctx_t ctx)
{
struct adapter *adapter = iflib_get_softc(ctx);
/*
* Just count the event; iflib(4) will already trigger a
* sufficient reset of the controller.
*/
adapter->watchdog_events++;
}
/*********************************************************************
*
* This routine disables all traffic on the adapter by issuing a
* global reset on the MAC and deallocates TX/RX buffers.
* global reset on the MAC.
*
* This routine should always be called with BOTH the CORE
* and TX locks.
**********************************************************************/
static void
em_if_stop(if_ctx_t ctx)
{
struct adapter *adapter = iflib_get_softc(ctx);
INIT_DEBUGOUT("em_stop: begin");
INIT_DEBUGOUT("em_if_stop: begin");
e1000_reset_hw(&adapter->hw);
if (adapter->hw.mac.type >= e1000_82544)
@ -1857,7 +1854,6 @@ em_if_stop(if_ctx_t ctx)
e1000_cleanup_led(&adapter->hw);
}
/*********************************************************************
*
* Determine hardware revision.
@ -2226,11 +2222,9 @@ em_setup_msix(if_ctx_t ctx)
/*********************************************************************
*
* Initialize the hardware to a configuration
* as specified by the adapter structure.
* Workaround for SmartSpeed on 82541 and 82547 controllers
*
**********************************************************************/
static void
lem_smartspeed(struct adapter *adapter)
{
@ -2395,6 +2389,12 @@ igb_init_dmac(struct adapter *adapter, u32 pba)
}
}
/*********************************************************************
*
* Initialize the hardware to a configuration as specified by the
* adapter structure.
*
**********************************************************************/
static void
em_reset(if_ctx_t ctx)
{
@ -2629,6 +2629,11 @@ em_reset(if_ctx_t ctx)
e1000_check_for_link(hw);
}
/*
* Initialise the RSS mapping for NICs that support multiple transmit/
* receive rings.
*/
#define RSSKEYLEN 10
static void
em_initialize_rss_mapping(struct adapter *adapter)
@ -2669,7 +2674,6 @@ em_initialize_rss_mapping(struct adapter *adapter)
E1000_MRQC_RSS_FIELD_IPV6_TCP_EX |
E1000_MRQC_RSS_FIELD_IPV6_EX |
E1000_MRQC_RSS_FIELD_IPV6);
}
static void
@ -2769,7 +2773,7 @@ igb_initialize_rss_mapping(struct adapter *adapter)
/*********************************************************************
*
* Setup networking device structure and register an interface.
* Setup networking device structure and register interface media.
*
**********************************************************************/
static int
@ -4015,12 +4019,6 @@ em_add_hw_stats(struct adapter *adapter)
SYSCTL_ADD_ULONG(ctx, child, OID_AUTO, "link_irq",
CTLFLAG_RD, &adapter->link_irq,
"Link MSI-X IRQ Handled");
SYSCTL_ADD_ULONG(ctx, child, OID_AUTO, "mbuf_defrag_fail",
CTLFLAG_RD, &adapter->mbuf_defrag_failed,
"Defragmenting mbuf chain failed");
SYSCTL_ADD_ULONG(ctx, child, OID_AUTO, "tx_dma_fail",
CTLFLAG_RD, &adapter->no_tx_dma_setup,
"Driver tx dma failure in xmit");
SYSCTL_ADD_ULONG(ctx, child, OID_AUTO, "rx_overruns",
CTLFLAG_RD, &adapter->rx_overruns,
"RX overruns");
@ -4543,7 +4541,8 @@ em_enable_vectors_82574(if_ctx_t ctx)
u16 edata;
e1000_read_nvm(hw, EM_NVM_PCIE_CTRL, 1, &edata);
printf("Current cap: %#06x\n", edata);
if (bootverbose)
device_printf(dev, "EM_NVM_PCIE_CTRL = %#06x\n", edata);
if (((edata & EM_NVM_MSIX_N_MASK) >> EM_NVM_MSIX_N_SHIFT) != 4) {
device_printf(dev, "Writing to eeprom: increasing "
"reported MSI-X vectors from 3 to 5...\n");

View File

@ -519,7 +519,6 @@ struct adapter {
u64 que_mask;
struct em_int_delay_info tx_int_delay;
struct em_int_delay_info tx_abs_int_delay;
struct em_int_delay_info rx_int_delay;
@ -529,9 +528,6 @@ struct adapter {
/* Misc stats maintained by the driver */
unsigned long dropped_pkts;
unsigned long link_irq;
unsigned long mbuf_defrag_failed;
unsigned long no_tx_dma_setup;
unsigned long no_tx_map_avail;
unsigned long rx_overruns;
unsigned long watchdog_events;