SCSI) the data returned for latched residual and error statistics.
Reserve space for LOG SENSE data which we'll get later. This area
in transition as the HP TapeAlert initiative is looked at.
The optimisation of only waiting before issuing new commands is
obviously invalid in general and it caused many errors in NIST-PCTS.
I think the errors were mostly for characters sent with the wrong
parity, etc., after a half complete tcsetattr().
Use microtime() instead of a magic loop count to limit the wait.
The wait is a busy-wait :-( and normally takes about 500 usec.
AcerLabs Aladdin-V. It makes the PCI probing work when system booting. I
will try to merge some additional funtion(i.e. wdc1 problem cause tons of
PR appear :<) ASAP if I could.
Remind me if something wrong after committing, thanks!
The Winbond chip always includes the CRC with every received frame,
and I can't find anything in the Winbond manual that indicates you can
program it not to do this.
Submitted by: "Richard Seaman, Jr." <lists@tar.com>
Obtained from: linux :-)
Code to allow Linux Threads to run under FreeBSD.
By default not enabled
This code is dependent on the conditional
COMPAT_LINUX_THREADS (suggested by Garret)
This is not yet a 'real' option but will be within some number of hours.
most of them).
Many thanks to Kevin Van Maren for the work here, Intel for lending us
a 450NX system to work this out on, and several other folks for testing
the patches. See the PR for an extensive discussion of the nature of
the problem and resolution.
PR: kern/8928
Submitted by: Kevin Van Maren <vanmaren@fast.cs.utah.edu>
- created internal names for fixed-size integral types, like __int32_t. They
will be used to make several headers self-sufficient.
- <stdlib.h> don't include <machine/types.h> anymore.
- created <sys/inttypes.h>, which can be used as <inttypes.h>.
- declaration of uoff_t and ufs_daddr_t moved to <sys/types.h>.
Reviewed by: bde
0x02000000. This error was causing the chip to always include the
ethernet CRC along with every received frame (the driver turns on
PN_NETCFG_NO_RXCRC, but it was frobbing the wrong bit).
almost works properly. Unfortunately, there is no way to flush
the rx fifo without resetting the channel, which also flushes the
tx fifo. We avoid resetting even when both fifos need to be flushed,
since resetting seems to cause the rx to lose sync if it is done
while data is arriving.
Reminded by: NIST-PCTS
Attempt to determine (at mount time if not done so already) via density code
whether a device should default to fixed mode or not. Attempts to set to
variable that fail will cause fixed to be selected.
Similarly, the '2 filemarks at EOM' quirk is now determined (or attempted to
be determined) via density code. Some as yet not entirely tested code for
coping with 2FM@EOD position is now also in place.
hardware is interrupt-driven to a fault and sending a BREAK requires
mode switching. Always running in the BREAK-capable mode as in PR 8318
would double the overhead for sending \0's.
Reminded by: PR 8318
Use the host message loop for any unknown message types instead of performing
a reject message in the sequencer. Pass reject messages to the host
message loop too which frees up a sequencer interrupt type slot.
Default to issuing a bus reset if initiator mode is enabled. It seems
that the reset scsi bus bit is not defined in the same location for
all aic78xx BIOSes, so attempting to honor this setting will have to
wait until I get more information on how to detect it.
Nuke some unused variables.
aborted prior to disabling our lun. This requires a second set of
links since we use the ones in the ccb_hdr during normal operations.
Nuke some unused variables.
and out of kernel address space (via the pass(4) and xpt(4) peripheral
drivers) to 64K (DFLTPHYS). Some controllers, like the Adaptec 1542,
don't support more than 64K transactions.
We plan on eventually having the capability of limiting this size based
on min(MAXPHYS, controller max), but since that capability isn't here yet,
limit things to the lowest common denominator.
Not tested on the if_sr, if_cx and if_ar drivers, but
expected to work just the same as it used to.
Any users of these drivers (or even better: donors
of hardware for them) please contact phk@freebsd.org
so we can test the next batch of changes to if_sppp.
reporting since this past summer. (I think Daniel O'Conner was the first.)
The problem appears to have been something like this:
- cdda2wav by default passes in a buffer that is close to the 128K MAXPHYS
limit.
- many times, the buffer is not page aligned
- vmapbuf() truncates the address, so that it is page aligned
- that causes the total size of the buffer to be greater than MAXPHYS,
which of course is a bad thing.
Here's a quote from the PR (kern/9067):
==================
In particular, note bp->b_bufsize = 0x0001f950 and bp->b_data = 0xf2219960
(which does not start on a page boundary). vunmapbuf() loops through all
the pages without any difficulty until addr reaches 0xf2239000, and then
the panic occurs. This seems to indicate that we are exceeding MAXPHYS
since we actually started from the middle of a page (the data is being
transfered to a non page aligned location).
To complete the description, note that the system call originates from
ReadCddaMMC12() (in scsi_cmds.c of cdda2wav) with a request to read 55
audio sectors of 2352 bytes (which is calculated to fall under MAXPHYS).
This in turn ends up calling scsi_send() (in scsi-bsd.c) which calls
cam_fill_csio() and cam_send_ccb(). This results in a CAMIOCOMMAND ioctl
with a ccb function code of XPT_SCSI_IO.
==================
The fix is to change the size check in cam_periph_mapmem() so that it is
like the one in minphys(). In particular, it is something like:
if ((buffer_length + (buf_ptr & PAGE_MASK)) > MAXPHYS)
buffer is too big
My fix is based on the one in the PR, but I cleaned up a fair number of
things in cam_periph_mapmem(). The checks for each buffer to be mapped
are now in a separate loop from the actual mapping operation. With the new
arrangement, we don't have to bother with unmapping any previously mapped
buffers if one of the checks fails.
Many thanks to James Liu for tracking this down. I'd appreciate it if some
vm-savvy folks would look this over. I believe this fix is correct, but I
could be wrong.
PR: kern/9067 (also, kern/8112)
Reviewed by: gibbs
Submitted by: "James T. Liu" <jtliu@phlebas.rockefeller.edu>
adjusted related casts to match (only in the kernel in this commit).
The pointer was only wanted in one place in kern_exec.c. Applications
should use the kern.ps_strings sysctl instead of PS_STRINGS, so they
shouldn't notice this change.
across the kernel -> application interface, and for the one sysctl where
they were passed and actually used (kern.ps_strings), the applications
want addresses represented as u_longs anyway (the other sysctl that
passed them, kern.usrstack, has never been used).
Agreed to by: dfr, phk
as well as several functional additions.
(1) dot3 MIB support.
(2) if_media selection method support.
(3) bridge support.
(4) new boards support. Supported boards are as follows.
[PC/AT]
* Fujitsu FMV-180 series
* Allied-Telesis RE2000 series
* Allied-Telesyn AT1700 series
* Gateway Communications G/Ether series
* UB networks Access/PC ISA series
* TDK/LANX LAC-AX series
* ICL EtherTeam16i series
* RATOC REX-5586/5587
[PC-98]
* Allied-Telesis RE1000 series
* Allied-Telesis RE1000Plus/ME1500 series
* Contec C-NET(9N)E series
* Contec C-NET(98)P2 series
* UB networks Access/PC N98C+ series
* TDK/LANX LAC-98 series(not tested)
Submitted by: seki@sysrap.cs.fujitsu.co.jp (Masahiro Sekiguchi) and
chi@bd.mbn.or.jp (Chiharu Shibata)
in rev.1.30 (just before FreeBSD-1.1R) to almost match corresponding
breakage in FreeBSD-1.x's diskerr(). FreeBSD-2.x's diskerr() never
had the breakage.
in target mode, but we are not completing the command.
Use a template of allowed bus arbitration phases to selectively and
dynamically enable/disable initiator or target (re)selection.
Properly handle timeouts for target role transactions - just go to the
bus free state and report the error to the peripheral driver.
Checkpoint support for the XPT_ABORT_CCB function code. This currently
handles the accept tio and immediate notify ccb types, but does not
handle the continue target I/O or SCSI I/O ccb types. This is enough
to handle dynamic target enable/disable events.
Clean up the SCSI reset code so that we perform at most 1 SCSI bus
reset at initialization, the reset requested by the XPT layer.
level so they can be reclaimed before attempting to disable our lun.
Correctly free descriptors. Add periph locking and spl protection
around open and close.
pointed this out, but I've not seen a manifestation of this.
o Check against 0x00 as well as 0xff for geometry register, as some clone
cards don't return 0xff. Vadim Mikhailov pointed this out in PR
8743 for his Dell SCSI Array controller working in AHA-1540
emulation mode. Note that this test is likely to go away in the
future in favor of a better one Justin has recommended.
memory address space rather than IO space.. reflect this when looking for the
interface revision register.
If this is not true for them all then we probably need some smarter code.
bug, but set it to 0 anyway to get rid of warning.
Get rid of uninitialized warning for local variable 'line' as well as
make a minor change to its scope. Again, no bug.
const char *. Originally I was going to add casts from const char * to
char * in some of the pci device drivers, but the reality is that the
pci device probes return constant quoted strings.
Add bounds checking to netbios NS packet resolving code. This should
prevent natd from crashing on badly formed netbios packets (as might be
heard when the machine is sitting on a cable modem or certain DSL
networks), and also closes potential security holes that might have
exploited the lack of bounds checking in the previous version of the
code.
- For transactions of 0 length, us a non-residual checking CCB type.
- Preserve command status if our interrupt handler completes a command
while we are polling for completion in aha_cmd.
If timer calculation results in degenerate value (0), force it to 1
to avoid divide-by-zero panic later on in calls to IGMP_RANDOM_DELAY().
I considered simply adding 1 to the timer calculation, but was unsure
if the calculation was part of the IGMP standard or not so did not want
to mess with it for all cases.
Obtained from: Stephen Clawson <sclawson@cs.utah.edu>
Wakeup anyone waiting on a mount point prior to returning from umount,
whether an error occurs or not. Fixes a stat/NFS-umount race and other
potential future problems. Fix taken from bug/pr which also indicated
that the same fix has already been applied to OpenBSD and NetBSD.
This is odd, especially in the case of USB where the driver is found
in several tries: vendor specific, class specific, interface specific.
The mouse driver is found at the interface specific level...
Reviewed by: Doug Rabson (dfr@freebsd.org)
floppy is used on the toshiba Libretto line of subnotebook computers.
It differs from a normal floppy in that you must use PIO rather than
DMA to transfer the data.
To enable this, you must add options "FDC_YE" to your kernel. I don't
have a machine that has a floppy and a pcmcia slot to test to make
sure that this doesn't impact normal floppy units, so I've left this as
an option.
I have ported this to -current and made an attempt to ensure that the
indentation conforms to style(9), aka the bruce filter.
Reviewed by: nate, markm
Submitted by: David Horwitt (dhorwitt@ucsd.edu)
incorporate some notion of which revision the device is. If it's < SCSI2, for
example, READ BLOCK LIMITS is not a MANDATORY command.
At any rate, the initial state is to try and read block limits to get a notion
of the smallest and largest record size as well as the granularity. However,
this doesn't mean that the device should actually *in* fixed block mode should
the max && min be equal... *That* choice is (for now) determined by whether
the device comes up with a blocksize of nonzero. If so, then it's a fixed block
preferred device, otherwise not (this will change again soon).
When actually doing I/O, and you're in fixed length mode, the block count is
*not* the byte count divided by the minimum block size- it's the byte count
divided by the current blocksize (or use shift/mask shortcuts if that worked
out...).
Then when you *change* the blocksize via an ioctl, make sure this actually
propagates to the stored notion of blocksize (and update the shift/mask
shortcuts).
Misc Other:
When doing a mode select, only use the SCSI_SAME_DENSITY (0x7f) code if
the device is >= SCSI2- otherwise just use the saved density code.
Recover from the ripple of ILLEGAL REQUEST not being 'retried' in that
RESERVE/RELEASE is not a mandatory command for < SCSI2 (so ignore it if it
fails).
but the present PCI probe code still thinks we are there as the pci attach
can't return an error code.
This means we are in the shared interrupt list, but have not been set up.
If we are sharing ints with another device, ohci_intr will be called and will
coredump on a NULL reference. So just return if it is called when not set up.
This fixes the symptom and not the cause.
The right answer is to let the PCI system know that the attach failed,
or to fail earlier (in the PCI probe).
The attach() is a void fn() so it can't return failure..
If we are not transfering any data, use a non S/G ccb type that doesn't
return residual information. It seems that some firmware revisions dislike
S/G ccbs with 0 length S/G lists.
Correct bt_cmd() so that we always honor command status that was latched
by our interrupt routine while polling for completion..
programs using glibc expect edx to be preserved accross syscalls.
As a result, linux programs running in emulation mode can
have whatever value may be represented by edx clobbered.
PR: 9038
Submitted-By: Richard Seaman, Jr. <dick@tar.com>
is more robust and common code can be used for both the target and iniator
roles. The mechanism for tracking negotiation state has also been simplified.
Add support for sync/wide negotiation in target mode and fix many of
the target mode bugs running at higher speeds uncovered. Make a first
stab at getting all of the bus skew delays correct. Sync+Wide dataout
transfers still cause problems, but this may be an initiator problem.
Ensure that we exit BITBUCKET mode if the controller is restarted.
Add support for target mode only firmware downloads. This has been
tested on the aic7880, but should mean that we can perform target mode
on any aic7xxx controller. Mixed mode (initiator and target roles in
the same firmware load) is currently only supported on the aic7890, but
with optimization, may fit on chips with less instruction space.
Allow sync transfers if the controller supports it. Wide will follow
as soon as I get the kinks worked out of wide target transfers in the
aic7xxx driver (currently the only target mode driver in the tree).
to specify that it does not provide initiator services (PIM_NOINITIATOR)
and that the initial bus reset for device probing should be avoided
(PIM_NOBUSRESET).
Modify the XPT layer to honor these flags.
0. This makes it difficult to do efficient manipulation of the
struct pollfd since you can't leave a slot empty.
PR: 8599
Submitted-by: Marc Slemko <marcs@znep.com>
