The dead list thread is sufficient for synchronization.
Retire the arch_id (ldt array slot) in the gc thread instead of the
doing it in the thread itself.
Approved by: re/jhb
are not initialized at this place. Move the initializing
before the non-blocking check.
Submitted by: Marius Strobl <marius@alchemy.franken.de>
Reviewed by: jhb
Approved by: re
value to be written into tick_compare in tick_hardclock(). While
we were taking care that the value to be written was at least TICK_GRACE
ticks in the future, a vector interrupt could happen between calculating
the value and writing it. If it took longer than TICK_GRACE to complete
(which is doubtful for a single device-triggered vector interrupt, but
quite likely for some IPIs), the value written would be in the past
and tick interrupts (which drive hardclock and statclock) would stop
until %tick wraps around, which takes a long time.
Also, increase TICK_GRACE from 1000 to 10000 for good measure.
Reported by: kris
Reviewed by: jake
Approved by: re (scottl)
low-level lock used by the libpthread implementation. In the
future, we'll eliminate spinlocks from libc but that will wait
until after 5.1-release.
Don't call an application signal handler if the handler is
the same as the library-installed handler. This seems to
be possible after a fork and is the cause of konsole hangs.
Approved by: re@ (jhb)
ID allocation is not there yet. This fixes a few warnings about \_OS_ not
being found and an S3 freeze for one user.
Re-staticize AcpiNsRemoveReference() since it is not needed elsewhere.
Approved by: re (scottl)
buf_start() to avoid triggering a panic in softdep_disk_io_initiation()
if b_iocmd happened to be BIO_READ. The later initialisation of
b_iocmd in cluster_wbuild() could probably be moved to before the
buf_start() call, but this patch keeps the change as simple as
possible.
This is reported to fix occasional "softdep_disk_io_initiation: read"
panics, especially on NFS servers.
Reported by: Nick Hilliard <nick@netability.ie>
Tested by: Nick Hilliard <nick@netability.ie>
Approved by: re (rwatson)
just read() in non-blocking mode too. The reason is obvious. NetBSD
uses a complete different way to get the credentials so this patch
only applies to FreeBSD.
Reviewed by: rwatson
Approved by: re
Remove the special treatment of non-blocking mode in
the "look ahead function" xdrrec_eof(). It currently
assumes that the last read() in a row of several reads
does not have zero lenght. If this is the case, svc_vc_stat()
does return XPRT_MOREREQS, and the RPC-request aborts because
there is no data to read anymore.
To fix this, go back to the original version of the code
for non-blocking mode until NetBSD comes up with another
possible fix like this one in xdrrec_eof()
if (rstrm->last_frag && rstrm->in_finger == rstrm->in_boundry) {
return TRUE;
}
Return always FALSE in set_input_fragment() for non-blocking
mode. Since this was not used in FreeBSD, I omitted it at the
first time. Now we use this function and we should always
return FALSE for it.
Reviewed by: rwatson
Approved by: re
function couldn't handle chains of > MCLBYTES, and it had a bug which
caused corruption and panics in certain low mbuf situations.
Additionally, change the failure case so that looutput returns ENOBUFS
rather than attempting to pass on non-defragmented mbuf chains.
Finally, remove the printf which would happen every time the low memory
situation occured. It served no useful purpose other than to clue me
in as to what was causing the panic in question. :)
MFC after: 4 days
joiner by making sure all locks and unlocks occur in the same order. For
the record the lock order is: DEAD_LIST, THREAD_LIST, exiting thread, joiner
thread.
Approved by: re/rwatson
865. The APSIZE register has a variable-sized field of enabled bits.
To figure out how many bits a specific host bridge supports, write the
maximum width and see how many bits are set in the hardware. We then
use this mask for setting and getting the aperture size. Prior to this,
the agp(4) driver would treat an aperture size of 256 MB as 128 MB and
would not allocate enough physical memory for the GART as a result.
MFC after: 3 days
Sponsored by: The Weather Channel
Approved by: re (rwatson)
NetBSD dsmethod.c rev 1.7
Fix parent-child loop problem
Fix a reference count problem that may cause unexpected memory free
Intel 20030512 ACPICA drop (nsalloc.c)
Approved by: re (jhb)
Obtained from: NetBSD, Intel
Reported by: mbr, kochi AT netbsd.org
BUS_DMASYNC_ definitions remain as before. The does not change the ABI,
and reverts the API to be a bit more compatible and flexible. This has
survived a full 'make universe'.
Approved by: re (bmah)
used by DDB and we cannot know in advance whether it's save to
sleep. It often enough isn't. We may want to pre-allocate space
to cover the most common cases without having to use malloc at
all, but that requires some analysis. We leave that for later.
Approved by: re@ (blanket)
o If the address was not within user space we jumped to fusufault
where we would clear pcb_onfault and return 0. There are two
bugs here:
1. We never got to the point where we assigned the address of
pcb_onfault to r15, which means that we would clobber some
random memory location, including I/O space or ROM.
2. We're supposed to return -1 on error.
o Make sure we have proper memory ordering for setting pcb_onfault,
doing the memory access to user space and clearing pcb_onfault.
For the fu* family of functions this means that we need a mf
instruction, because we don't have acquire semantics on stores
and release semantics on loads (hence st;ld cannot be ordered
without intermediate mf).
While here, implement casuptr() so that we are a (small) step
closer to supporting libthr and deobfuscate the non-implementation
of {f|s}uswintr.
Approved by: re@ (blanket)
VM_ALLOC_INTERRUPT to VM_ALLOC_SYSTEM. There was no mention of
this in commit log as it was considered harmless. Guess what:
it does harm. WITNESS showed that we can not safely grab the
page queue lock in vm_page_alloc() in all cases as we may have
to sleep on it. Revert the request to VM_ALLOC_INTERRUPT to
circumvent this. We panic if vm_page_alloc returns 0. I'm not
entirely happy about this, but we have bigger fish to fry.
Approved by: re@ (blanket)
aic79xx.c:
In ahd_handle_ign_wide_residue():
o Use SCB_XFERLEN_ODD SCB field to determine transfer
"oddness" rather than the DATA_COUNT_ODD logic.
SCB_XFERLEN_ODD is toggled on every ignore wide
residue message so that multiple ignore wide residue
messages for the same transaction are properly supported.
o If the sg list has been exausted, the sequencer
doesn't bother to update the residual data count
since it is known to be zero. Perform the zeroing
manually before calculating the remaining data count.
o Use multibyte in/out macros instead of shifting/masking
by hand.
aic79xx_inline.h:
In ahd_setup_scb_common(), setup the SCB_XFERLEN_ODD field.
aic79xx.reg:
Use the SCB_TASK_ATTRIBUTE field as a bit field in the
non-packetized case. We currently only define one bit,
SCB_XFERLEN_ODD.
Remove the ODD_SEG bit field that was used to carry the odd
transfer length information through the SG cache. This
is obviated by SCB_XFERLEN_ODD field.
Remove the DATA_COUNT_ODD scratch ram byte that was used
dynamicaly compute data transfer oddness. This is obviated
by SCB_XFERLEN_ODD field.
aic79xx.seq:
Remove all updates to the DATA_COUNT_ODD scratch ram field.
Remove all uses of ODD_SEG. These two save quite a few
sequencer instructions.
Use SCB_XFERLEN_ODD to validate the end of transfer
ignore wide residue message case.
aic7xxx.c:
In ahc_handle_ign_wide_residue():
o Use SCB_XFERLEN_ODD SCB field to determine transfer
"oddness" rather than the DATA_COUNT_ODD logic.
SCB_XFERLEN_ODD is toggled on every ignore wide
residue message so that multiple ignore wide residue
messages for the same transaction are properly supported.
o If the sg list has been exausted, the sequencer
doesn't bother to update the residual data count
since it is known to be zero. Perform the zeroing
manually before calculating the remaining data count.
o Ensure that SG_LIST_NULL is cleared in the
residual sg pointer for "mid-transfer" ignore
wide residue cases.
o Use multibyte in/out macros instead of shifting/masking
by hand.
aic7xxx.h:
Modify the SCB_GET_LUN() macro to mask the lun hardware
SCB field with LID. This leaves two bits in the LUN
field that can be used for other purposes.
aic7xxx.reg:
Change LID to be 0x3F. This is the maximum supported
lun size for non-packetized SCSI. Map the top bit
of the lun to SCB_XFERLEN_ODD. The host must set
this bit whenever a transfer is an odd length.
Remove the ODD_SEG bit field that was used to carry the odd
transfer length information through the SG cache. This
is obviated by SCB_XFERLEN_ODD field.
Remove the DATA_COUNT_ODD scratch ram byte that was used
dynamicaly compute data transfer oddness. This is obviated
by SCB_XFERLEN_ODD field.
aic7xxx.seq:
Be more careful in our handling of the SCB_LUN field. It
must be masked with LID if only lun information is desired.
Remove all updates to the DATA_COUNT_ODD scratch ram field.
Remove all uses of ODD_SEG. These two save quite a few
sequencer instructions.
Use SCB_XFERLEN_ODD to validate the end of transfer
ignore wide residue message case.
aic7xxx_inline.h:
In ahc_queue_scb(), setup the SCB_XFERLEN_ODD field.
Approved by: RE
FAILDIS in the SEQCTL register, not the HCNTRL register.
aic7xxx.c:
Remeber SEQCTL settings in the "seqctl" field of our
softc. seqctl defaults to just having FASTMODE set,
but the bus attachments can override this.
aic7xxx.h:
Add the seqctl softc field.
aic7xxx_pci.c:
Update the seqctl softc field and manually update SEQCTL
when to many PCI errors occur
Approved by: RE
to be more efficient by having the sequencer copy the
single byte of valid lun data into the long lun field.
aic79xx.c:
Memset our hardware SCB to 0 so that untouched
fields don't confuse diagnostic output. With the
old method for handling the Rev A bug, if the long
lun field was not 0, this could result in bogus
lun information being sent to drives.
Use the same SCB transfer size for all chip types
now that the long lun is not DMA'ed to the chip.
aic79xx.seq:
Add code to copy lun information for Rev.A hardware.
aic79xx_inline.h:
Remove host update of the long_lun field on every
packetized command.
Sort IDs based on chip type.
Remove IROC IDs. We'll switch to using the IROC masks
if/when we want to start attaching to IROC controllers.
Approved by: RE
