in some commercial Unix systems, which utilizes Huffman minimum redundancy
code tree to compress files. This implementation supports the "new" pack
format only, just like GNU gzip did.
Thanks for oliver@'s archive set which I can test against, and Mingyan Guo
for providing helpful review of my code.
PR: bin/109567
MFC after: 1 month
To detect which controller is ICH based one, add a new member
variable ich to struct fxp_ident and move the struct to
if_fxpvar.h. Since I've faked controller revision, don't allow
microcode loading for ICH based controllers.
With this change all ICH based controllers will have WOL and Rx
checksum offload capability.
PR: kern/135451
Tested by: Alexey Shuvaev ( shuvaev <> physik dot uni-wuerzburg dot de ),
pluknet ( pluknet <> gmail dot com ),
Gary Jennejohn ( gary.jennejohn <> freenet dot de )
not allow multicast filter programming when controller is busy to
send/receive frames. So it used to mark need_mcsetup bit and defer
multicast filter programming until controller becomes idle state.
To detect when the controller is idle fxp(4) relied on Tx
completion interrupt with NOP command and fxp_start_body and
fxp_intr_body had to see whether pending multicast filter
programming was requested. This resulted in very complex logic and
sometimes it did not work as expected.
Since the controller should be in idle state before any multicast
filter modifications I changed it to reinitialize the controller
whenever multicast filter programming is required. This is the same
way what OpenBSD and NetBSD does. Also I added IFF_DRV_RUNNING
check in ioctl handler so controller would be reinitialized only if
it is absolutely needed.
With this change I guess we can remove fxp(4) DELAY hack in ifioctl
for IPv6 case.
upper stack in fxp_start_body().
fxp(4) drops driver lock in Rx path so check the fxp(4) is still
running after reacquiring driver lock in Rx path. Also don't
invoke fxp_intr_body if fxp(4) is not running. With this change
there is no need to set suspend bit in device attach phase.
hardware reset in attach phase. Selective reset does not clear
configured parameters so I think full hardware reset is required.
To prevent PCI bus lock-up, do selective reset first which will get
off the controller from PCI bus and request software reset after
selective reset. Software reset will unmask interrupts so disable
it after the reset.
common mbuf dma tag for both Tx and Rx path but Rx buffer should
have single DMA segment and maximum buffer size of the segment
should be less than MCLBYTES.
fxp(4) also have to check Tx completion status which was updated by
DMA so we need BUS_DMASYNC_PREREAD and BUS_DMASYNC_POSTWRITE
synchronization in Tx path. Fix all misuse of bus_dmamap_sync(9) in
fxp(4). I guess this change shall fix occasional driver breakage in
PAE environments.
While I'm here add error messages of dma tag/buffer creation and
correct messages.
Formerly, it was possible for the file to be created between the check if it
existed and the open; the contents would then be lost.
Because this must use O_EXCL, noclobber > will not create a file through a
symlink anymore. This agrees with behaviour of other shells.
Approved by: ed (mentor) (implicit)
getgroups for ibcs emulation. It seems vanishingly likely any
programs will actually be affected since they probably assume a much
lower value and use a static array size.
pointer to the containing mbuf. This eliminates a strong assumption
about the layout of network buffer memory, giving us greater
flexibility to revise mbuf semantics in the future.
reassembly but failed to be modernized over time:
- Use queue(9).
- Specifically allocate queue entries of type M_SPXREASSQ to point at
member mbufs, rather than casting mbuf data to 'spx_q'.
- Maintain the mbuf pointer as part of the queue entry so that we can
later free the mbuf without using dtom().
Intel agrees with my reading of the docs, make it so for all G4X chips.
The new register also has a 32 bit width as opposed to 24 bits. Fix
things up so that the counters roll over properly.
MFC after: 3 days
Now that we start to use credentials on character devices more often
(because of MPSAFE TTY), move the prison-checks that are in place in the
TTY code into devfs.
Instead of strictly comparing the prisons, use the more common
prison_check() function to compare credentials. This means that
pseudo-terminals are only visible in devfs by processes within the same
jail and parent jails.
Even though regular users in parent jails can now interact with
pseudo-terminals from child jails, this seems to be the right approach.
These processes are also capable of interacting with the jailed
processes anyway, through signals for example.
Reviewed by: kib, rwatson (older version)
altered through their .init code. This might happen if init
vector calls dlopen on its own and that dlopen causes some not
yet initialized object to be initialized earlier as part of that
dlopened DAG.
Do not reset module reference counts to zero on final fini vector
run when process is exiting. Just add an additional parameter to
force fini vector invocation regardless of current reference count
value if object was not destructed yet. This allows dlclose called
from fini vector to proceed normally instead of failing with handle
validation error.
Reviewed by: kib
Reported by: venki kaps
not in cpu_exit(). The latter is called after td_md.md_highfp_mtx
has been destroyed, which results in a race condition when another
thread wants to use the high FP registers on the CPU that still has
the high FP registers in question.
- remove mbuf iovec - useful, but adds too much complexity when isolated to
the driver
- remove driver private caching - insufficient benefit over UMA to justify
the added complexity and maintenance overhead
- remove separate logic for managing multiple transmit queues, with the
new drbr routines the control flow can be made to much more closely resemble
legacy drivers
- remove dedicated service threads, with per-cpu callouts one can get the same
benefit much more simply by registering a callout 1 tick in the future if there
are still buffered packets
- remove embedded mbuf usage - Jeffr's changes will (I hope) soon be integrated
greatly reducing the overhead of using kernel APIs for reference counting
clusters
- add hysteresis to descriptor coalescing logic
- add coalesce threshold sysctls to allow users to decide at run-time
between optimizing for forwarding / UDP or optimizing for TCP
- add once per second watchdog to effectively close the very rare races
occurring from coalescing
- incorporate Navdeep's changes to the initialization path required to
convert port and adapter locks back to ordinary mutexes (silencing BPF
LOR complaints)
- enable prefetches in get_packet and tx cleaning
Reviewed by: navdeep@
MFC after: 2 weeks
Output quoted suitable for re-input to the shell occurs in
various cases such as 'set', 'trap'.
Bugfix: *, ? and [ must be quoted (except sole [)
Bugfix: ~ and # must be quoted (really only sometimes, but keep it simple)
Bugfix: space, tab and newline must always be quoted
Shortening: other IFS characters do not need quoting
Bugfix: send to correct output file, not hard-coded stdout
Shortening: avoid unnecessary '' with \'
Approved by: ed (mentor)
