Seems like a copy-paste error, or at least this made more sense when the
sio(4) driver still existed. This modifies the debug port name displayed
at boot, but otherwise has no functional change.
Reviewed by: hselasky
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D33278
After switching the dongle to the Huawei alternate mode(modem mode)
with usb_modeswitch the serial interfaces had all of their ids set to
0xFF.
After modifying umodem to work with that it attached successfully and
I've managed to configure device with standard AT commands to get
internet connection.
folder, only keeping the zero length packet API introduced in sys/dev/usb
after more reports of USB serial devices not supporting ZLPs.
Reported by: mav@
MFC after: 1 week
Sponsored by: NVIDIA Networking
port devices. If it gets eaten it is fine. Many USB device side implementations
don't properly support the clear endpoint halt command and if they do, data is lost
because the transmit FIFO is typically reset when this command is received.
Tested by: jmg
MFC after: 1 week
Sponsored by: NVIDIA Networking
Also hide shim code added in a previous commit under COMPAT_USBHID12.
Note: it is enough to add -DCOMPAT_USBHID12 to CFLAGS to compile old
code with new HID subsystem, but it is not enough to link it at runtime.
HID dependency has to be added explicitly with MODULE_DEPEND macro.
Reviewed by: manu, hselasky (as part of D27887)
It will be used by the upcoming HID-over-i2C implementation. Should be
no-op, except hid.ko module dependency is to be added to affected drivers.
Reviewed by: hselasky, manu
Differential revision: https://reviews.freebsd.org/D27867
Code changes in this commit were obtained from straight from OpenBSD's
uplcom.c with almost no modification, the list of chip names and USB
IDs was obtained from Linux.
Differential Revision: https://reviews.freebsd.org/D27952
Submitted by: tomli_tomli.me (Yifeng Li)
MFC after: 1 week
Sponsored by: Mellanox Technologies // NVIDIA Networking
r357614 added CTLFLAG_NEEDGIANT to make it easier to find nodes that are
still not MPSAFE (or already are but aren’t properly marked). Use it in
preparation for a general review of all nodes.
This is non-functional change that adds annotations to SYSCTL_NODE and
SYSCTL_PROC nodes using one of the soon-to-be-required flags.
Reviewed by: hselasky, kib
Approved by: kib (mentor)
Differential Revision: https://reviews.freebsd.org/D23632
The datasheets for these chips claim the maximum is 921,600, but testing
shows these two higher rates also work (but no rates above 921,600 other
than these two work; these represent dividing the base buad clock by 3 and 2
respectively).
o Remove All Rights Reserved from my notices
o imp@FreeBSD.org everywhere
o regularize punctiation, eliminate date ranges
o Make sure that it's clear that I don't claim All Rights reserved by listing
All Rights Reserved on same line as other copyright holders (but not
me). Other such holders are also listed last where it's clear.
Enable this for the NovAtel OEMv2 GPS receiver.
Not fixed: The receiver shows up as "<Interface 0>" in the device
tree, because that is literally what the descriptor-string is.
Reviewed by: hselasky@
asserted. Some development boards for example will reset on DTR,
and some radio interfaces will transmit on RTS.
This patch allows "stty -f /dev/ttyu9.init -rtsdtr" to prevent
RTS and DTR from being asserted on open(), allowing these devices
to be used without problems.
Reviewed by: imp
Differential Revision: https://reviews.freebsd.org/D20031
This allows replacing "sys/eventfilter.h" includes with "sys/_eventfilter.h"
in other header files (e.g., sys/{bus,conf,cpu}.h) and reduces header
pollution substantially.
EVENTHANDLER_DECLARE and EVENTHANDLER_LIST_DECLAREs were moved out of .c
files into appropriate headers (e.g., sys/proc.h, powernv/opal.h).
As a side effect of reduced header pollution, many .c files and headers no
longer contain needed definitions. The remainder of the patch addresses
adding appropriate includes to fix those files.
LOCK_DEBUG and LOCK_FILE_LINE_ARG are moved to sys/_lock.h, as required by
sys/mutex.h since r326106 (but silently protected by header pollution prior
to this change).
No functional change (intended). Of course, any out of tree modules that
relied on header pollution for sys/eventhandler.h, sys/lock.h, or
sys/mutex.h inclusion need to be fixed. __FreeBSD_version has been bumped.
the current fixed values, which enables use of rates above 1 Mbps.
Improved the detection of HXD chips, and the status flag handling as
well.
Submitted by: Gabor Simon <gabor.simon75@gmail.com>
PR: 225932
Differential revision: https://reviews.freebsd.org/D16639
MFC after: 1 week
Sponsored by: Mellanox Technologies
This change adds support for a UBS<->RS232 adapter based on CH340 (or an
analogue) that I own. The device seems to have a newer internal version
(0x30) and the existing code incorrectly configures line control for it
resulting in garbled transmission. The changes are based on what I
learned in Linux drivers for the same hardware.
Additional changes:
- use UCHCOM_REG_LCR1 / UCHCOM_REG_LCR2 instead of explicit 0x18 and
0x25
- use NULL instead of 0 where a pointer is expected
Reviewed by: hselasky
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D15498
Also, add definitions for more bits of UCHCOM_REG_LCR1 as seen in the
Linux driver. UCHCOM_LCR1_PARENB definition was different from that in
the Linux driver and clashed with newly added UCHCOM_LCR1_RX. I took a
liberty to change UCHCOM_LCR1_PARENB to the Linux definition as it was
unused in the driver anyway. This change should make
uchcom_cfg_set_break() easier to understand.
Approved by: hselasky
MFC after: 2 weeks
Product IDs are specified in vendor documents. The previously used
device ID is not. This is a cosmetic change. No functionality depends
on those IDs.
Reviewed by: hselasky
MFC after: 2 weeks
device-side (and only device-side) "virtual USB serial adapters" - the
ones you can get with an OTG-capable board - as consoles. It boils down
to adding the device name to kern.console sysctl, although doing that
requires jumping through some hoops. It doesn't change the actual
operation of those virtual devices. The point is to make it possible
for init(8) to recognize them as console devices and to launch getty(8)
for them, when configured as "onifconsole" in ttys(5). The point of
that, in turn, is to add such entries to the default ttys(5), so that
init(8) will launch gettys for device-side "virtual serial adapters",
but not for actual USB serial dongles.
Reviewed by: hselasky@
No objections: imp@
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
the jtag port, so that a tty is not created for it.
This is based on information in the PR and from the vendor website. When
the PR was first opened we had no facility for flagging the jtag ports. I
stumbled across the still-open PR with the idea of closing it, and noticed
that this wee update was needed.
PR: 175893
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
The tty layer uses tsw_busy to poll for busy/idle status of the transmitter
hardware during close() and tcdrain(). The ucom layer defines ULSR_TXRDY and
ULSR_TSRE bits for the line status register; when both are set, the
transmitter is idle. Not all chip drivers maintain those bits in the sc_lsr
field, and if the bits never get set the transmitter will always appear
busy, causing hangs in tcdrain().
These changes add a new sc_flag bit, UCOM_FLAG_LSRTXIDLE. When this flag is
set, ucom_busy() uses the lsr bits to return busy vs. idle state, otherwise
it always returns idle (which is effectively what happened before this
change because tsw_busy wasn't implemented).
For the uftdi chip driver, these changes stop masking out the tx idle bits
when processing the status register (because now they're useful), and it
calls ucom_use_lsr_txbits() to indicate the bits are maintained by the
driver and can be used by ucom_busy().
Differential Revision: https://reviews.freebsd.org/D9183
