uart_dev_ns8250 now relies on compatible property instead of additional
'busy-detect' cell. All drivers with compatible = "snps,dw-apb-uart" have
busy detection turned on. DTS files of devices affected by the change
were modified and 'busy-detect' property was removed.
Reviewed by: andrew, ian, imp
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4218
This compatibility string is used in .dts file of Armada38x
and isrequired for driver attachment.
Reviewed by: andrew, ian, imp
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Michal Stanek <mst@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4216
to actually wait until the TX FIFOs of UARTs have be drained before
returning. This is done by bringing the equivalent of the TS_BUSY flag
found in the previous implementation back in an ABI-preserving way.
Reported and tested by: Patrick Powell
Most likely, drivers for USB-serial-adapters likewise incorporating
TX FIFOs as well as other terminal devices that buffer output in some
form should also provide implementations of tsw_busy.
MFC after: 3 days
on FDT/OFW platforms.
After the refactoring of the powerpc code so that OF_decode_addr() is usable
on all FDT/OFW platforms, this switches uart(4) to using it.
Differential Revision: https://reviews.freebsd.org/D4675
option to invert the polarity in software. Also add an option to capture
very narrow pulses by using the hardware's MSR delta-bit capability of
latching line state changes.
This effectively reverts the mistake I made in r286595 which was based on
empirical measurements made on hardware using TTL-level signaling, in which
the logic levels are inverted from RS-232. Thus, this re-syncs the polarity
with the requirements of RFC 2783, which is writen in terms of RS-232
signaling.
Narrow-pulse mode uses the ability of most ns8250 and similar chips to
provide a delta indication in the modem status register. The hardware is
able to notice and latch the change when the pulse width is shorter than
interrupt latency, which results in the signal no longer being asserted by
time the interrupt service code runs. When running in this mode we get
notified only that "a pulse happened" so the driver synthesizes both an
ASSERT and a CLEAR event (with the same timestamp for each). When the pulse
width is about equal to the interrupt latency the driver may intermittantly
see both edges of the pulse. To prevent generating spurious events, the
driver implements a half-second lockout period after generating an event
before it will generate another.
Differential Revision: https://reviews.freebsd.org/D4477
block. Use it in all the PNP drivers to export either the current PNP
table. For uart, create a custom table and export it using
MODULE_PNP_INFO since it's the only one that matches on function
number.
Differential Review: https://reviews.freebsd.org/D3461
It turns out on a 16550 w/ a 25MHz SoC reference clock you get a little
over 3% error at 115200 baud, which causes this to fail.
Just .. cope. Things cope these days.
Default to 30 (3.0%) as before, but allow UART_DEV_TOLERANCE_PCT to be
set at build time to change that.
vendor supplied device trees contain the needed properties for us to select
the correct uart to use as the kernel console.
An example of this would be to add the following to loader.conf.
hw.fdt.console="/smb/uart@f7113000"
The intention of this is slightly different than the existing
hw.uart.console option. The new option will mean the boot serial
configuration will be derived from the device node, while the existing
option expects the user to configure all this themselves.
Further work is planned to allow the uart configuration to be set based on
the stdout-path property devicetree bindings.
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D3559
electrical signals on the serial port. Virtually all devices which output a
PPS signal generate a brief higher-voltage pulse, the leading edge of which
is the on-time point.
Both DCD and CTS are active-low signals on the wire, meaning the assertion
of their status bits in the modem status register corresponds to the lower
voltage level on the wire. So when the status bit transitions to not-set,
create a PPS assert event; when the status bit transitions to set, create a
PPS clear event.
eliminating the need to build a custom kernel to use the CTS signal.
The historical UART_PPS_ON_CTS kernel option is still honored, but now it
can be overridden at runtime using a tunable to configure all uart devices
(hw.uart.pps_mode) or specific devices (dev.uart.#.pps_mode). The per-
device config is both a tunable and a writable sysctl.
This syncs the PPS capabilities of uart(4) with the enhancements recently
recently added to ucom(4) for capturing from USB serial devices.
Relnotes: yes
time_pps_fetch() to be used in blocking mode.
Also, don't init the pps api for system devices (consoles) that provide a
custom attach routine. The device may actually be a keyboard or other non-
tty device. If it wants to do pps processing (unlikely) it must handle
everything for itself. (In reality, only a sun keyboard uses a custom
attach routine, and it doesn't make a good pps device.)
uart_bus_attach() during its test that 20 iterations weren't sufficient
for clearing all pending interrupts, assuming this means that hardware
is broken and doesn't deassert interrupts. However, under pressure, 20
iterations also can be insufficient for clearing all pending interrupts,
leading to a panic as intr_event_handle() tries to schedule an interrupt
handler not registered. Solve this by introducing a flag that is set in
test mode and otherwise restores pre-r253161 behavior of uart_intr(). The
approach of additionally registering uart_intr() as handler as suggested
in PR 194979 is not taken as that in turn would abuse special pccard and
pccbb handling code of intr_event_handle(). [1]
- Const'ify uart_driver_name.
- Fix some minor style bugs.
PR: 194979 [1]
Reviewed by: marcel (earlier version)
MFC after: 3 days
polling at device attach time [1].
Add tunables 'debug.uart_force_poll' and 'debug.uart_poll_freq' to control
uart polling.
Submitted by: Aleksey Kuleshov (rndfax@yandex.ru) [1]
files to vendor-provided ones. It should make easier to adopt platform
code to new revisions of hardware and to use DTS overlays for various
Beaglebone extensions (shields/capes).
Original dts filenames were not changed, they're now wrappers over dts
files provided by TI. So make sure you update .dtb files on your
devices as part of kernel update
GPIO addressing was changed: instead of one global /dev/gpioc0 there
are per-bank instances of /dev/gpiocX. Each bank has 32 pins so for
instance pin 121 on /dev/gpioc0 in old addressing scheme is now pin 25
on /dev/gpioc3
On Pandaboard serial console devices was changed from /dev/ttyu0 to
/dev/ttyu2 so you'll have to update /etc/ttys to get login prompt
on serial port in multiuser mode. Single user mode serial console
should work as-is
Differential Revision: https://reviews.freebsd.org/D2146
Reviewed by: rpaulo, ian, Michal Meloun, Svatopluk Kraus
This is needed with the pl011 driver. Before this change it would default
to a shift of 0, however the hardware places the registers at 4-byte
addresses meaning the value should be 2.
This patch fixes this for the pl011 when configured using the fdt. The
other drivers have a default value of 0 to keep this a no-op.
MFC after: 1 week
uart implementations, and export them using the new linker-set mechanism.
Differential Revision: https://reviews.freebsd.org/D1993
Submitted by: Michal Meloun
(class and device) FDT UART. Define second one, UART_FDT_CLASS, for UART
class only.
This paves the way for declaring uart_class data and ofw/fdt compat data
with a uart implementation, rather than needing a big global table of
compat data and weak-symbol declarations of every existing implementation.
Differential Revision: https://reviews.freebsd.org/D1992
Submitted by: Michal Meloun
is the case, depending on the options, in some of the ARM hardware
simulators. In these cases we don't get an interrupt so will need to
schedule the task to write more data to the uart.
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
chips with the same device and vendor IDs actually may provide different
functionality. While at it, canonicalize the description to match other
MosChip UARTs.
PR: 186891
MFC after: 3 days
This will allow to attach UART drivers lying directly on the root node
instead of simple-bus compatible bus only.
Obtained from: Semihalf
Sponsored by: The FreeBSD Foundation
Instead of waiting for empty TX FIFO it is more reasonable to
block on full FIFO. As soon as FIFO slot is free the character
can be transmitted.
In case of TX FIFO disabled, TXFF bit indicates that transmit
register is not empty.
Obtained from: Semihalf
Reviewed by: andrew, emaste
Sponsored by: The FreeBSD Foundation
in userland rename in-kernel getenv()/setenv() to kern_setenv()/kern_getenv().
This fixes a namespace collision with libc symbols.
Submitted by: kmacy
Tested by: make universe
doesn't have support for the Z8530. Embedded PowerPC platforms
typically don't. Fail when the device class we actually need is
not present.
Obtained from: Juniper Networks, Inc.
This includes:
o All directories named *ia64*
o All files named *ia64*
o All ia64-specific code guarded by __ia64__
o All ia64-specific makefile logic
o Mention of ia64 in comments and documentation
This excludes:
o Everything under contrib/
o Everything under crypto/
o sys/xen/interface
o sys/sys/elf_common.h
Discussed at: BSDcan
These changes prevent sysctl(8) from returning proper output,
such as:
1) no output from sysctl(8)
2) erroneously returning ENOMEM with tools like truss(1)
or uname(1)
truss: can not get etype: Cannot allocate memory
there is an environment variable which shall initialize the SYSCTL
during early boot. This works for all SYSCTL types both statically and
dynamically created ones, except for the SYSCTL NODE type and SYSCTLs
which belong to VNETs. A new flag, CTLFLAG_NOFETCH, has been added to
be used in the case a tunable sysctl has a custom initialisation
function allowing the sysctl to still be marked as a tunable. The
kernel SYSCTL API is mostly the same, with a few exceptions for some
special operations like iterating childrens of a static/extern SYSCTL
node. This operation should probably be made into a factored out
common macro, hence some device drivers use this. The reason for
changing the SYSCTL API was the need for a SYSCTL parent OID pointer
and not only the SYSCTL parent OID list pointer in order to quickly
generate the sysctl path. The motivation behind this patch is to avoid
parameter loading cludges inside the OFED driver subsystem. Instead of
adding special code to the OFED driver subsystem to post-load tunables
into dynamically created sysctls, we generalize this in the kernel.
Other changes:
- Corrected a possibly incorrect sysctl name from "hw.cbb.intr_mask"
to "hw.pcic.intr_mask".
- Removed redundant TUNABLE statements throughout the kernel.
- Some minor code rewrites in connection to removing not needed
TUNABLE statements.
- Added a missing SYSCTL_DECL().
- Wrapped two very long lines.
- Avoid malloc()/free() inside sysctl string handling, in case it is
called to initialize a sysctl from a tunable, hence malloc()/free() is
not ready when sysctls from the sysctl dataset are registered.
- Bumped FreeBSD version to indicate SYSCTL API change.
MFC after: 2 weeks
Sponsored by: Mellanox Technologies
uart2: <Intel AMT - PM965/GM965 KT Controller> port 0x1830-0x1837
mem 0xfe024000-0xfe024fff irq 17 at device 3.3 on pci0
uart2: console (115200,n,8,1)
Tested as tty and serial console. Seems "fine"
{MIO,SER}5xxxx chips instead of treating all of them as PUC_PORT_2S.
Among others, this fixes the hang seen when trying to probe the none-
existent second UART on an actually 1-port chip.
Obtained from: NetBSD (BAR layouts)
MFC after: 3 days
Sponsored by: Bally Wulff Games & Entertainment GmbH
CLOCAL and HUPCL control flags. There are legit reasons for allowing
those to be changed. When /etc/ttys has the "3wire" type (without a
baudrate) for the serial port that is the low-level console, then
this change has no effect.
Obtained from: Juniper Networks, Inc.
baudrate of the device special file, and makes sure that on open(2) the
UART is programmed with the correct baudrate. This then eliminates the
need in uart_tty_param() to override the speed setting.
to check the status property in their probe routines.
Simplebus used to only instantiate its children whose status="okay"
but that was improper behavior, fixed in r261352. Now that it doesn't
check anymore and probes all its children; the children all have to
do the check because really only the children know how to properly
interpret their status property strings.
Right now all existing drivers only understand "okay" versus something-
that's-not-okay, so they all use the new ofw_bus_status_okay() helper.
console, it calls the grab functions. These functions should turn off
the RX interrupts, and any others that interfere. This makes mountroot
prompt work again. If there's more generalized need other than
prompting, many of these routines should be expanded to do those new
things.
Should have been part of r260889, but waasn't due to command line typo.
Reviewed by: bde (with reservations)
obsolete. This involves the following pieces:
- Remove it entirely on PowerPC, where it is not used by MD code either
- Remove all references to machine/fdt.h in non-architecture-specific code
(aside from uart_cpu_fdt.c, shared by ARM and MIPS, and so is somewhat
non-arch-specific).
- Fix code relying on header pollution from machine/fdt.h includes
- Legacy fdtbus.c (still used on x86 FDT systems) now passes resource
requests to its parent (nexus). This allows x86 FDT devices to allocate
both memory and IO requests and removes the last notionally MI use of
fdtbus_bs_tag.
- On those architectures that retain a machine/fdt.h, unused bits like
FDT_MAP_IRQ and FDT_INTR_MAX have been removed.
static device mappings.
This SoC relied heavily on the fact that all devices were static-mapped
at a fixed address, and it (rather bogusly) used bus_space read and write
calls passing hard-coded virtual addresses instead of proper bus handles,
relying on the fact that the virtual addresses of the mappings were known
at compile time, and relying on the implementation details of arm
bus_space never changing. All such usage was replaced with calls to
bus_space_map() to obtain a proper bus handle for the read/write calls.
This required adjusting some of the #define values that map out hardware
registers, and some of them were renamed in the process to make it clear
which were defining absolute physical addresses and which were defining
offsets. (The ones that just define offsets don't appear to be referenced
and probably serve no value other than perhaps documentation.)
clients. Mask RX interrupts while grabbed on the atmel serial
driver. This UART interrupts every character. When interrupts are
enabled at the mountroot> prompt, this means the ISR eats the
characters. Rather than try to create a cooperative buffering system
for the low level kernel console, instead just mask out the ISR. For
NS8250 and decsendents this isn't needed, since interrupts only happen
after 14 or more characters (depending on the fifo settings). Plumb
such that these are optional so there's no change in behavior for all
the other UART clients. ddb worked on this platform because all
interrupts were disabled while it was running, so this problem wasn't
noticed. The mountroot> issue has been around for a very very long
time.
MFC after: 3 days
strings as uart_bus_fdt's probe().
The bus code uses ofw_bus_search_compatible() and that's not an option in
cpu (console) code -- it runs way before the ofw routines are usable. So
the console probe has its own loop to search the table, but now at least
there's only one table to be maintained when new devices are added.
/chosen, following the list of allowed console properties in ePAPR. Also
do not require that stdin be defined and equal to stdout: stdin is
nonstandard (for ePAPR) and console in an unexpected place is after all
better than no console.
When using DW UART with BUSY detection it is necessary to wait
until all serial transfers are finished before manipulating the
line control. LCR will not be affected when UART is busy.
In addition, if Divisor Latch Access Bit is being set in order to
modify UART divisors:
1. We will get BUSY interrupt if interrupts are enabled.
2. Because LCR will not be affected the THR and (even worse) IER
contents will be corrupted. This will lead to console hang.
Approved by: cognet (mentor)
is not giving us a 100% success rate. Bump the delay to 200ms as
that seems to do the trick.
Note that during testing the delay was added to uart_bus_attach()
in uart_core.c. While having the delay in a different place can
change the behaviour, it was not expected. Having to bump the
delay with another 50ms could therefore be an indication that
the problem can not be solved with delays.
Reported by: kevlo@
Tested by: kevlo@
calls ns8250_bus_ipend() almost immediately after ns8250_bus_attach().
As it appears, a line break condition is being signalled for almost
all received characters due to this. A delay of 150ms seems enough
to allow the H/W to settle and to avoid the problem.
More analysis is needed, but for now a regression has been addressed.
Reported by: kevlo@
Tested by: kevlo@
The TI uart hardware is ns16550-compatible, except that before it can
be used the clocks and power have to be enabled and a non-standard
mode control register has to be set to put the device in uart mode
(as opposed to irDa or other serial protocols). This adds the extra
code in an extension to the standard ns8250 probe routine, and the
rest of the driver is just the standard ns8250 code.
This makes it easier to implement new drivers which are "mostly ns8250"
but with some small difference such as needing to enable clocks or poke
a non-standard register at probe or attach time.
device compatible with multiple drivers matches the more specific driver
first and doesn't overwrite it later with the more generic. Move the
generic ns16550 to the end of the list.
we call device-specific probe functions, which can (and typically will)
set the device description based on low-level device probe information.
In the end we never actually used the device description that we so
carefully maintained in the PCI match table. By setting the device
description after we call uart_probe(), we'll print the more user-
friendly description by default.
