The BWD NTB device will drop the link if an error is encountered on the
point-to-point PCI bridge. The link will stay down until all errors are
cleared and the link is re-established. On link down, check to see if
the error is detected, if so do the necessary housekeeping to try and
recover from the error and reestablish the link.
There is a potential race between the 2 NTB devices recovering at the
same time. If the times are synchronized, the link will not recover and
the driver will be stuck in this loop forever. Add a random interval to
the recovery time to prevent this race.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
There is a Xeon hardware errata related to writes to SDOORBELL or B2BDOORBELL
in conjunction with inbound access to NTB MMIO Space, which may hang the
system. To workaround this issue, use one of the memory windows to access the
interrupt and scratch pad registers on the remote system. This bypasses the
issue, but removes one of the memory windows from use by the transport. This
reduction of MWs necessitates adding some logic to determine the number of
available MWs.
Since some NTB usage methodologies may have unidirectional traffic, the ability
to disable the workaround via modparm has been added.
See BF113 in
http://www.intel.com/content/dam/www/public/us/en/documents/specification-updates/xeon-c5500-c3500-spec-update.pdf
See BT119 in
http://www.intel.com/content/dam/www/public/us/en/documents/specification-updates/xeon-e5-family-spec-update.pdf
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
Due to ambiguous documentation, the USD/DSD identification is backward
when compared to the setting in BIOS. Correct the bits to match the
BIOS setting.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
The NTB Xeon hardware has 16 scratch pad registers and 16 back-to-back
scratch pad registers. Correct the #define to represent this and update
the variable names to reflect their usage.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Alexander Motin <mav@freebsd.org>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Reviewed by: Justin Gibbs <gibbs@scsiguy.com>
Reviewed by: Xin Li <delphij@freebsd.org>
Approved by: Gordon Ross <gordon.ross@nexenta.com>
Author: George Wilson <george.wilson@delphix.com>
illumos/illumos-gate@632802744e
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Simon Klinkert <simon.klinkert@gmail.com>
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed by: Albert Lee <trisk@omniti.com>
Reviewed by: Xin Li <delphij@freebsd.org>
Approved by: Garrett D'Amore <garrett@damore.org>
Author: George Wilson <george.wilson@delphix.com>
illumos/illumos-gate@139510fb6e
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Albert Lee <trisk@omniti.com>
Reviewed by: Xin Li <delphij@freebsd.org>
Approved by: Garrett D'Amore <garrett@damore.org>
Author: George Wilson <george.wilson@delphix.com>
illumos/illumos-gate@b10bba7246
This doesn't free the mbuf upon error; the driver ic_raw_xmit method is still
doing that.
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3774
Move error handling into ieee80211_parent_xmitpkt() instead of spreading it
between functions.
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3772
* Create ieee80211_free_mbuf() which frees a list of mbufs.
* Use it in the fragment transmit path and ath / uath transmit paths.
* Call it in xmit_pkt() if the transmission fails; otherwise fragments
may be leaked.
This should be a big no-op.
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3769
The system will appear to lockup for long periods of time due to the NTB
driver spending too much time in memcpy. Avoid this by reducing the
number of packets that can be serviced on a given interrupt.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
The ring logic of the NTB receive buffer/transmit memory window requires
there to be at least 2 payload sized allotments. For the minimal size
case, split the buffer into two and set the transport_mtu to the
appropriate size.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
If the NTB link toggles, the driver could stop receiving due to the
tx_index not being set to 0 on the transmitting size on a link-up event.
This is due to the driver expecting the incoming data to start at the
beginning of the receive buffer and not at a random place.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
Each link-up will allocate a new NTB receive buffer when the NTB
properties are negotiated with the remote system. These allocations did
not check for existing buffers and thus did not free them. Now, the
driver will check for an existing buffer and free it if not of the
correct size, before trying to alloc a new one.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
64bit BAR sizes are permissible with an NTB device. To support them
various modifications and clean-ups were required, most significantly
using 2 32bit scratch pad registers for each BAR.
Also, modify the driver to allow more than 2 Memory Windows.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
->remote_rx_info and ->rx_info are struct ntb_rx_info pointers. If we
add sizeof(struct ntb_rx_info) then it goes too far.
Authored by: Dan Carpenter
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
This allows to set delete method via tunable, before device capabilities
are known. Also allow ZERO method for devices not reporting LBP, if user
explicitly requests it -- it may be useful if storage supports compression
and WRITE SAME, but does not support UNMAP.
MFC after: 2 weeks
I am not sure what for it was done. Now open routine should automatically
fall back to read-only if open for writing is impossible. In such case
attempt to upgrade to write sounds strange.
MFC after: 1 week
This change fixes some amount of -Wsign-conversion and -Wconversion warnings
and sets correct sizes for some variables (as a result, some loop counters
were touched too).
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3763
This removes the need for manually changing this flag for Google Chrome
users. It also improves compatibility with Linux applications running under
Linuxulator compatibility layer, and possibly also helps in porting software
from Linux.
Generally speaking, the flag allows applications to create the shared memory
segment, attach it, remove it, and then continue to use it and to reattach it
later. This means that the kernel will automatically "clean up" after the
application exits.
It could be argued that it's against POSIX. However, SUSv3 says this
about IPC_RMID: "Remove the shared memory identifier specified by shmid from
the system and destroy the shared memory segment and shmid_ds data structure
associated with it." From my reading, we break it in any case by deferring
removal of the segment until it's detached; we won't break it any more
by also deferring removal of the identifier.
This is the behaviour exhibited by Linux since... probably always, and
also by OpenBSD since the following commit:
revision 1.54
date: 2011/10/27 07:56:28; author: robert; state: Exp; lines: +3 -8;
Allow segments to be used even after they were marked for deletion with
the IPC_RMID flag.
This is permitted as an extension beyond the standards and this is similar
to what other operating systems like linux do.
MFC after: 1 month
Relnotes: yes
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3603
reads and writes.
PR: kern/198405
Submitted by: Matthew D. Fuller <fullermd at over-yonder dot net>
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3679
* Shuffle the kernel to be at the beginning
* Give the kernel 2mb, the rootfs 6mb, and 'mib0' the rest
* put the cfg parition just before the ART calibration data for the
wifi part in the SoC
* .. and make sure ART points to the right 64k region.
I've updated the freebsd-wifi-build wiki the instructions on using this.
If someone has an AP135 with 8MB SPI flash then this won't work; everything
minus the big mib0 partition is just a bit over 8MB. Come see me if this
ever happens (you'll likely just have to shrink the rootfs and the kernel
a little in order to make it fit.)
Tested:
* AP135 reference board.
