A timecounter will be selected when registered if its quality is
not negative and no less than the current timecounters.
Add a sysctl to report all available timecounters and their qualities.
Give the dummy timecounter a solid negative quality of minus a million.
Give the i8254 zero and the ACPI 1000.
The TSC gets 800, unless APM or SMP forces it negative.
Other timecounters default to zero quality and thereby retain current
selection behaviour.
Sign extension happens after the shift, not before so that boundary
cases like 0x40000000 will not be caught properly.
Instead, right shift ndirty. It is guaranteed to be a multiple of 8.
While here, do some manual code motion and code commoning.
Range check bug pointed out by: iedowse
We didn't try to list all the variants so there isn't much shrinkage
here.
Remove list of supported mlx(4) devices; readers should get this
information from the manual page.
case, a "Vortex86" mini PC), the PCI device ID value in the EEPROM (0x8100)
does not agree with the PCI device ID returned by pci_get_device() (0x8139).
This means that while rl_probe() matches the device, rl_attach() doesn't.
Work around this by adding an entry to the rl_devs table for the 8100 with
a device ID of 0x8100.
Also, get rid of extra instance of __FBSDID(). One is enough.
- Update some stale comments.
- Sort a couple of includes.
- Only set 'newcpu' in updatepri() if we use it.
- No functional changes.
Obtained from: bde (via an old diff I got a long time ago)
get the same value from ip->i_ump->um_devvp.
This saves a pointer in the memory copies of inodes, which can
easily run into several hundred kilobytes.
The extra indirection is unmeasurable in benchmarks.
Approved by: mckusick
- deprecate routes#N, as it is hard to keep consistency with
rtprefixN. accept any number of "rtprefix", "rtrefix0",
..., "rtprefix99".
- deprecate "addrs#N", as it is difficult for users to keep
consistency with "addrN".
accept 100 prefix info in maximum - like "addr", "addr0"
... "addr99". WARNS=2 clean on netbsd.
old configuration file should work just fine.
behavior change:
previously, we rejected "addrN" if there's "addr", and we rejected
"addr" if there is "addrN". now we accept both without problem.
- when an advertised prefix configured from the kernel has been added
or invalidated, notice the change in a short delay.
- when invalidating a prefix, do not bark even if there is
inconsistency about prefix lifetimes.
- wrap more specific route info code into ROUTEINFO.
Obtained from: KAME
MFC after: 1 week
- Add a macro for the logical shift needed to extract an APIC ID from
either from the local APIC ICR Hi register or the APIC ID registers of
the local and IO APICs.
This code dates back to the very first diskless support on FreeBSD,
back when swapon(8) couldn't simply be run on a NFS backed file.
Suggested replacement command sequence on the client:
dd if=/dev/zero of=/swapfile bs=1k count=1 oseek=100000
swapon /swapfile
rm -f /swapfile
For whatever value of 100000 you want.
Minor code reorganization was required, but the only functional
change was that the first 1024 bytes of output are thrown out
after each reseed, rather than just the initial seed.
was masked. However KIMURA Yasuhiro-san noticed my mistake and was
kind enough to provide a better patch in PR 55581. I've merged that
into the routine. Hopefully I've not overlooked anything this time.
MFC After: 5 days
that were on the kernel stack into account. For now we write them
out to the register stack of the process before creating the dump.
This however is not the final solution. The problem is that we may
invalidate the coredump by overwriting vital information due to an
invalid backing store pointer. Instead we need to write the dirty
registers to an unused region of VM which will result in a seperate
segment in the coredump. For now we can at least get to all the
registers from a coredump.
and the move to control register to avoid dependency violations when
these functions are used. Note that explicit data and instruction
serialization also need to be in a subsequent instruction group.
This too requires that we have an igrp break here.
PT_SETKSTACK. These requests allow the tracing process to access the
dirty registers of the traced process that are on the kernel stack.
Note that there's currently no way to access the rnat register for
those dirty registers that are not (yet) covered by a nat collection
point. The interface for this is still being slept on.
Also note that implied by these requests is the division of work:
The tracing process has to keep track of where registers are spilled
and is responsible to figure out where the NaT bit of the stacked
registers are at any time during the execution of the traced process.
The kernel provides the interfaces but will not abstract the fact
that the register stack can be split. This model does not follow
the approach taken in Linux where PT_PEEK and PT_POKE deals with
this automagically.
check for permissions, do it for all requests, not the known requests.
Later when we actually service the request we deal with the invalid
requests we previously caught earlier.
This commit changes the behaviour of the ptrace(2) interface for
boundary cases such as an unknown request without proper permissions.
Previously we would return EINVAL. Now we return EBUSY or EPERM.
Platforms need to define __HAVE_PTRACE_MACHDEP when they have MD
requests. This makes the prototype of cpu_ptrace() visible and
introduces a call to this function for all requests greater or
equal to PT_FIRSTMACH.
Silence on: audit
Correctly handle additional disks without BIOS partition tables.
Previously, vinum_scandisk stopped scanning additional disks for
native partitions after any good partition was found. This applies
to all platforms, but was a particular problem on systems without
BIOS partition tables.
Submitted by: harti
