ifconfig, essentially stealing the lease until the user goes and changes
it. The alternative, sadly, is total dysfunction since bpf isn't in
GENERIC and network connectivity would otherwise fail completely on first
bootup when DHCP configuration was attempted again.
The ultimate answer here is to make either bpf a loadable kernel module
(which security conscious admins will be able to simply remove from /modules)
or come up with a lighter weight mechanism just for dhcp and other apps that
need to see broadcast packets but not otherwise sniff the wire in full
bpf glory.
in some code from C. Stone to parse the lease information. This is still
a WIP and this commit is largely intended to allow others to sync up; the
dhclient code still only works when doing dhcp configuration post-install
and requires a bit more work on the boot floppy before it will truly
work in the minimal bootstrapping role.
gigabit ethernet adapters. This includes two single port cards
(single mode and multimode fiber) and two dual port cards (also single
mode and multimode fiber). SysKonnect is currently the only
vendor with a dual port gigabit ethernet NIC.
The ports on dual port adapters are treated as separate network
interfaces. Thus, if you have an SK-9844 dual port SX card, you
should have both sk0 and sk1 interfaces attached. Dual port cards
are implemented using two XMAC II chips connected to a single
SysKonnect GEnesis controller. Hence, dual port cards are really
one PCI device, as opposed to two separate PCI devices connected
through a PCI to PCI bridge. Note that SysKonnect's drivers use
the two ports for failover purposes rather that as two separate
interfaces, plus they don't support jumbo frames. This applies to
their Linux driver too. :)
Support is provided for hardware multicast filtering, BPF and
jumbo frames. The SysKonnect cards support TCP checksum offload
however this feature is not currently enabled (hopefully it will
be once we get checksum offload support).
There are still a few things that need to be implemeted, like
the ability to communicate with the on-board LM80 voltage/temperature
monitor, but I wanted to get the driver under CVS control and into
-current so people could bang on it.
A big thanks for SysKonnect for making all their programming info
for these cards (and for their FDDI and token ring cards) available
without NDA (see www.syskonnect.com).
ADMtek AL981 "Comet" chipset. The AL981 is yet another DEC tulip clone,
except with simpler receive filter options. The AL981 has a built-in
transceiver, power management support, wake on LAN and flow control.
This chip performs extremely well; it's on par with the ASIX chipset
in terms of speed, which is pretty good (it can do 11.5MB/sec with TCP
easily).
I would have committed this driver sooner, except I ran into one problem
with the AL981 that required a workaround. When the chip is transmitting
at full speed, it will sometimes wedge if you queue a series of packets
that wrap from the end of the transmit descriptor list back to the
beginning. I can't explain why this happens, and none of the other tulip
clones behave this way. The workaround this is to just watch for the end
of the transmit ring and make sure that al_start() breaks out of its
packet queuing loop and waiting until the current batch of transmissions
completes before wrapping back to the start of the ring. Fortunately, this
does not significantly impact transmit performance.
This is one of those things that takes weeks of analysis just to come
up with two or three lines of code changes.
on CDs and FTP sites.
o Collapse some redundant code.
o Fix typo'd menu.
o Restrict searches properly to packages rather than categories.
o Small tweaks to signal handling.
All RELENG_3 candidates.
I simply forgot that I'd already proven this to be a "really good idea that
unfortunately didn't work at all" the *last* time I tried it. Now
I remember. Hmmm. I WILL defeat this evil problem.
feature of packages now so that no version info is embedded.
o Add a default X desktop menu offering afterstep, enlightenment, KDE, GNOME
and Windowmaker desktops instead of the boring twm(1) based one if the
user so chooses. This will require a little testing.
Networks Tigon 1 and Tigon 2 chipsets. There are a _lot_ of OEM'ed
gigabit ethernet adapters out there which use the Alteon chipset so
this driver covers a fair amount of hardware. I know that it works with
the Alteon AceNIC, 3Com 3c985 and Netgear GA620, however it should also
work with the DEC/Compaq EtherWORKS 1000, Silicon Graphics Gigabit
ethernet board, NEC Gigabit Ethernet board and maybe even the IBM and
and Sun boards. The Netgear board is the cheapest (~$350US) but still
yields fairly good performance.
Support is provided for jumbo frames with all adapters (just set the
MTU to something larger than 1500 bytes), as well as hardware multicast
filtering and vlan tagging (in conjunction with the vlan support in
-current, which I should merge into -stable soon). There are some hooks
for checksum offload support, but they're turned off for now since
FreeBSD doesn't have an officially sanctioned way to support checksum
offloading (yet).
I have not added the 'device ti0' entry to GENERIC since the driver
with all the firmware compiled in is quite large, and it doesn't really
fit into the category of generic hardware.
to now detect that CD you just remembered to put in the drive or that
pccard NIC that you've inserted (anybody can put pccardd in an mfsroot image
now you know.. :)
Requested by: Annelise Anderson <andrsn@andrsn.Stanford.EDU>
orthogonal to the other entries).
Clean up X selection code a bit.
Choose proper architecture subdirectories on mirror sites now that we've
gone fully to the new multi-arch directory scheme.
