simplifies certain device attachments (Kauai ATA, for instance), and makes
possible others on new hardware.
On G5 systems, there are several otherwise standard PCI devices
(Serverworks SATA) that will not allow their interrupt properties to be
written, so this information must be supplied directly from Open Firmware.
Obtained from: sparc64
the PIC also informs the platform at which IRQ level it can start
assigning IPIs, since this can depend on the number of IRQs
supported for external interrupts.
o Revamp the PIC I/F to only abstract the PIC hardware. The
resource handling has been moved to nexus, where it belongs.
o Include EOI and MASK+EOI methods to the PIC I/F in support of
INTR_FILTER.
o With the allocation of interrupt resources and setup of
interrupt handlers in the common platform code we can delay
talking to the PIC hardware after enumeration of all devices.
Introduce a call to powerpc_intr_enable() in configure_final()
to achieve that and have powerpc_setup_intr() only program the
PIC when !cold.
o As a consequence of the above, remove all early_attach() glue
from the OpenPIC and Heathrow PIC drivers and have them
register themselves when they're found during enumeration.
o Decouple the interrupt vector from the interrupt request line.
Allocate vectors increasingly so that they can be used for
the intrcnt index as well. Extend the Heathrow PIC driver to
translate between IRQ and vector. The OpenPIC driver already
has the support for vectors in hardware.
Approved by: re (blanket)
subset ("compatible", "device_type", "model" and "name") of the standard
properties in drivers for devices on Open Firmware supported busses. The
standard properties "reg", "interrupts" und "address" are not covered by
this interface because they are only of interest in the respective bridge
code. There's a remaining standard property "status" which is unclear how
to support properly but which also isn't used in FreeBSD at present.
This ofw_bus kobj-interface allows to replace the various (ebus_get_node(),
ofw_pci_get_node(), etc.) and partially inconsistent (central_get_type()
vs. sbus_get_device_type(), etc.) existing IVAR ones with a common one.
This in turn allows to simplify and remove code-duplication in drivers for
devices that can hang off of more than one OFW supported bus.
- Convert the sparc64 Central, EBus, FHC, PCI and SBus bus drivers and the
drivers for their children to use the ofw_bus kobj-interface. The IVAR-
interfaces of the Central, EBus and FHC are entirely replaced by this. The
PCI bus driver used its own kobj-interface and now also uses the ofw_bus
one. The IVARs special to the SBus, e.g. for retrieving the burst size,
remain.
Beware: this causes an ABI-breakage for modules of drivers which used the
IVAR-interfaces, i.e. esp(4), hme(4), isp(4) and uart(4), which need to be
recompiled.
The style-inconsistencies introduced in some of the bus drivers will be
fixed by tmm@ in a generic clean-up of the respective drivers later (he
requested to add the changes in the "new" style).
- Convert the powerpc MacIO bus driver and the drivers for its children to
use the ofw_bus kobj-interface. This invloves removing the IVARs related
to the "reg" property which were unused and a leftover from the NetBSD
origini of the code. There's no ABI-breakage caused by this because none
of these driver are currently built as modules.
There are other powerpc bus drivers which can be converted to the ofw_bus
kobj-interface, e.g. the PCI bus driver, which should be done together
with converting powerpc to use the OFW PCI code from sparc64.
- Make the SBus and FHC front-end of zs(4) and the sparc64 eeprom(4) take
advantage of the ofw_bus kobj-interface and simplify them a bit.
Reviewed by: grehan, tmm
Approved by: re (scottl)
Discussed with: tmm
Tested with: Sun AX1105, AXe, Ultra 2, Ultra 60; PPC cross-build on i386
- Remove __RMAN_RESORUCE_VISIBLE again. It's no longer required either
because of the above change or because struct rman is no longer hidden.
Reviewed by: grehan
Tested by: cross-compile on i386
the MacIO chip and PSIM's IOBus. Bus-specific drivers should
use the identify method to attach themselves to nexus so
interrupt can be allocated before the h/w is probed. The
'early attach' routine in openpic is used for this stage
of boot. When h/w is probed, the openpic can be attached
properly. It will enable interrupts allocated prior to
this.
