multiple algorithms and potentially collect multiple samples.
Instead of a single calibration interval we now have short and long
intervals; the long interval roughly corresponds to the previous
single interval. The short interval is used to speedup collection
of samples and happens much quicker. We make calls using the short
interval until we're told the calibration work is complete at which
point we fallback to the long interval. In addition there is a
much longer reset interval used to flush all calibration state and
cause everthing to start anew.
With these changes you can also disable calibration entirely by
setting the long interval to zero.
module; the ath module now brings in the hal support. Kernel
config files are almost backwards compatible; supplying
device ath_hal
gives you the same chip support that the binary hal did but you
must also include
options AH_SUPPORT_AR5416
to enable the extended format descriptors used by 11n parts.
It is now possible to control the chip support included in a
build by specifying exactly which chips are to be supported
in the config file; consult ath_hal(4) for information.
o eliminate private state indexed by 802.11 rate codes; use the hal's
rate tables directly to get the same info
o calculate a mask of operational rates to optimize lookups and checks
(instead of using for loops and similar)
o optimize size bin operations
o ignore rates marked as "do not use" in the hal phy tables
o fix bug that caused upshifting to break in 11g once the rate dropped
below 11Mb/s
o add more intelligent multi-rate tx schedules
o add support for 1/2 and 1/4 width channels
o add dev.ath.X.sample_stats sysctl to dump runtime statistics to the console
(needs to go up to a user app)
o export more tuning knobs via sysctls (still a couple of magic constants)
necessary workarounds, add code to detect these hangs and distinguish
them from other events; note this code is only invoked for anomalous
conditions and (at the moment) is a noop because the hang detection
code is in a new hal that's coming shortly
capabilities reported by the ap. These need to be cross-checked
against the local configuration in the vap. Previously we were
only checking the ap capabilities which meant that if an ap reported
it was ff-capable but we were not setup to use them we'd try to do
ff aggregation and drop the frame.
There are a number of problems to be fixed here but applying this
fix immediately as the problem causes all traffic to stop (and has
not workaround).
Reported by: Ashish Shukla
making the use of sc_hwmap to do direct mapping impractical. Switch to
indexing by the rate index instead of the rate code and adjust associated
state and logic appropriately. This has several benefits including
simplification of the led code.
o fix radiotap capture of HT rates
o fix conditional compilation of HT radiotap support to be based on the
hal having 5416 support; not the ABI version as hal builds may or may
not include 5416 support
o update tx rssi data only when an ACK was received
o return tx rssi from sampled data instead of the last frame
o track noise floor
o return rx rssi and noise floor (was broken)
o pass country code, outdoor indication, and ecm mode into the hal
when requesting a channel list
o add a console msg when regulatory setup fails
o add placeholder code to map between Atheros sku's and 802.11 sku's
that handles only the debug country code used to unlock the full
channel list (to be used only for debugging)
o fix multiple instances of mismapping the 802.11 location to the
outdoor indication (anywhere may be outdoor also)
in sta and adhoc modes; this should've been done forever ago as most all
drivers use this hook to set per-station transmit parameters such as for
tx rate control
o adjust drivers to remove explicit calls to the driver newassoc method
o don't use the key index to identify when the driver has been
asked to allocate a key slot, use an explicit flag; allows
drivers to force s/w fallback for entries in the global table
o change callback api to allocate driver resources for a crypto key:
- de-const the key parameter so drivers can muck with the flags
- on callback failure don't automatically try to setup s/w crypto;
instead the driver must now mark the key entry for s/w crypto and
the caller will re-attach the cipher module
NB: api change permits drivers more control over fallback to s/w
crypto (e.g. based on a limited number of h/w key slots)
some longstanding issues:
o pass the vap since it's now the "coin of the realm" and required
to do things like set initial tx parameters in private node
state for use prior to association
o pass the mac address as cards that maintain outboard station
tables require this to create an entry (e.g. in ibss mode)
o remove the node table reference, we only have one node table
and it's unlikely this will change so this is not needed to
find the com structure
o do not put the chip into full sleep in ath_stop as it gains
nothing and causes many parts to hang in ath_detach because we
may touch the chip during vap teardown; this may also fix issues
with unloading the module
o add a note in ath_detach to explain ath_hal_detach puts the
chip in low power mode; this is useful to know as it means
unloading the module will place a pci device in the lowest
possible power state
o leave an #ifdef notyet marker for powering down the chip when
a device is marked down; we can't do that until we handle all
the ways the driver may be entered and touch the chip
o fix resume by reloading the h/w key cache as it's been clobbered
(for pci) by the socket being powered off; for station mode we
directly stop+init the chip and then simulate a beacon miss to
get the upper layers sync'd up; for other configs we must brute
force stop+start the vaps so they go through the state machine
o add IEEE80211_C_STA capability to indicate sta mode is supported
(was previously assumed) and mark drivers as capable
o add ieee80211_opcap array to map an opmode to the equivalent capability bit
o move IEEE80211_C_OPMODE definition to where capabilities are defined so it's
clear it should be kept in sync (on future additions)
o check device capabilities in clone create before trying to create a vap;
this makes driver checks unneeded
o make error codes return on failed clone request unique
o temporarily add console printfs on clone request failures to aid in
debugging; these will move under DIAGNOSTIC or similar before release
- Limit grabbing the lock to SIOCSIFFLAGS.
- Move ieee80211_start_all() to SIOCSIFFLAGS.
- Remove SIOCSIFMEDIA as it is not useful.
- Limit ether_ioctl to only SIOCGIFADDR. SIOCSIFADDR and SIOCSIFMTU have no
affect as there is no input/output path in the vap parent. The vap code
will handle the reinit of the mac address changes.
- Split off ndis_ioctl_80211 as it was getting too different to wired devices.
This fixes a copyout while locked and a lock recursion.
Reviewed by: sam
