It is not listed in the boot sequence in the MP specification (1.4),
and it is explicitly ignored on modern CPUs. It was only ever required
when bootstrapping systems with external APICs (that is, SMP machines
with 486s), which FreeBSD has never supported (and never will).
While here, tidy some comments and remove some banal ones.
matches the algorithm in the MP specification (1.4). Previously we
were sending out the deassert INIT IPI immediately after the initial
INIT IPI was sent.
from pmap_pte(). PT_SET_MA() is not a queued mapping update, but instead
an immediate mapping update, so the page queues lock is not required here.
Reviewed by: cperciva
on x86 and use that to implement stop_emulating() in the fpu/npx code.
Reimplement start_emulating() in the non-XEN case by using load_cr0() and
rcr0() instead of the 'lmsw' and 'smsw' instructions. Intel explicitly
discourages the use of 'lmsw' and 'smsw' on 80386 and later processors in
the description of these instructions in Volume 2 of the ADM.
Reviewed by: kib
MFC after: 1 month
trampoline addresses after the shared page is enabled. Handle FreeBSD
ABIs without shared page support too.
Reported and tested by: David Wolfskill <david catwhisker org>
(previous version)
Pointy hat to: kib
MFC after: 1 month
usermode, using shared page. The structures and functions have vdso
prefix, to indicate the intended location of the code in some future.
The versioned per-algorithm data is exported in the format of struct
vdso_timehands, which mostly repeats the content of in-kernel struct
timehands. Usermode reading of the structure can be lockless.
Compatibility export for 32bit processes on 64bit host is also
provided. Kernel also provides usermode with indication about
currently used timecounter, so that libc can fall back to syscall if
configured timecounter is unknown to usermode code.
The shared data updates are initiated both from the tc_windup(), where
a fast task is queued to do the update, and from sysctl handlers which
change timecounter. A manual override switch
kern.timecounter.fast_gettime allows to turn off the mechanism.
Only x86 architectures export the real algorithm data, and there, only
for tsc timecounter. HPET counters page could be exported as well, but
I prefer to not further glue the kernel and libc ABI there until
proper vdso-based solution is developed.
Minimal stubs neccessary for non-x86 architectures to still compile
are provided.
Discussed with: bde
Reviewed by: jhb
Tested by: flo
MFC after: 1 month
- Stateful TCP offload drivers for Terminator 3 and 4 (T3 and T4) ASICs.
These are available as t3_tom and t4_tom modules that augment cxgb(4)
and cxgbe(4) respectively. The cxgb/cxgbe drivers continue to work as
usual with or without these extra features.
- iWARP driver for Terminator 3 ASIC (kernel verbs). T4 iWARP in the
works and will follow soon.
Build-tested with make universe.
30s overview
============
What interfaces support TCP offload? Look for TOE4 and/or TOE6 in the
capabilities of an interface:
# ifconfig -m | grep TOE
Enable/disable TCP offload on an interface (just like any other ifnet
capability):
# ifconfig cxgbe0 toe
# ifconfig cxgbe0 -toe
Which connections are offloaded? Look for toe4 and/or toe6 in the
output of netstat and sockstat:
# netstat -np tcp | grep toe
# sockstat -46c | grep toe
Reviewed by: bz, gnn
Sponsored by: Chelsio communications.
MFC after: ~3 months (after 9.1, and after ensuring MFC is feasible)
layer, but it is read directly by the MI VM layer. This change introduces
pmap_page_is_write_mapped() in order to completely encapsulate all direct
access to PGA_WRITEABLE in the pmap layer.
Aesthetics aside, I am making this change because amd64 will likely begin
using an alternative method to track write mappings, and having
pmap_page_is_write_mapped() in place allows me to make such a change
without further modification to the MI VM layer.
As an added bonus, tidy up some nearby comments concerning page flags.
Reviewed by: kib
MFC after: 6 weeks
- Remove cpuset stopped_cpus which is no longer used.
- Add a short comment for cpuset suspended_cpus clearing.
- Fix the un-ordered x86/acpica/acpi_wakeup.c in conf/files.amd64 and i386.
Pointed-out by: attilio@
suspend/resume procedures are minimized among them.
common:
- Add global cpuset suspended_cpus to indicate APs are suspended/resumed.
- Remove acpi_waketag and acpi_wakemap from acpivar.h (no longer used).
- Add some variables in acpi_wakecode.S in order to minimize the difference
among amd64 and i386.
- Disable load_cr3() because now CR3 is restored in resumectx().
amd64:
- Add suspend/resume related members (such as MSR) in PCB.
- Modify savectx() for above new PCB members.
- Merge acpi_switch.S into cpu_switch.S as resumectx().
i386:
- Merge(and remove) suspendctx() into savectx() in order to match with
amd64 code.
Reviewed by: attilio@, acpi@
Constify pc_freemask[].
pmap_pv_reclaim()
Eliminate "freemask" because it was a pessimization. Add a comment about
the resident count adjustment.
free_pv_entry() [i386 only]
Merge an optimization from amd64 (r233954).
get_pv_entry()
Eliminate the move to tail of the pv_chunk on the global pv_chunks list.
(The right strategy needs more thought. Moreover, there were unintended
differences between the amd64 and i386 implementation.)
pmap_remove_pages()
Eliminate unnecessary ()'s.
locked xchg instruction. IA32 memory model guarantees that store has
release semantic, since stores cannot pass loads or stores.
Reviewed by: bde, jhb
Tested by: pho
MFC after: 2 weeks
(described in ACPICA source code).
- Move intr_disable() and intr_restore() from acpi_wakeup.c to acpi.c
and call AcpiLeaveSleepStatePrep() in interrupt disabled context.
- Add acpi_wakeup_machdep() to execute wakeup MD procedures and call
it twice in interrupt disabled/enabled context (ia64 version is
just dummy).
- Rename wakeup_cpus variable in acpi_sleep_machdep() to suspcpus in
order to be shared by acpi_sleep_machdep() and acpi_wakeup_machdep().
- Move identity mapping related code to acpi_install_wakeup_handler()
(i386 version) for preparation of x86/acpica/acpi_wakeup.c
(MFC candidate).
Reviewed by: jkim@
MFC after: 2 days
longer uses the active and inactive paging queues. Instead, the pmap now
maintains an LRU-ordered list of pv entry pages, and pmap_pv_reclaim() uses
this list to select pv entries for reclamation.
Note: The old pmap_collect() tried to avoid reclaiming mappings for pages
that have either a hold_count or a busy field that is non-zero. However,
this isn't necessary for correctness, and the locking in pmap_collect() was
insufficient to guarantee that such mappings weren't reclaimed. The new
pmap_pv_reclaim() doesn't even try.
Tested by: sbruno
MFC after: 5 weeks
to this pmap.c. This new r/w lock is used primarily to synchronize access
to the PV lists. However, it will be used in a somewhat unconventional
way. As finer-grained PV list locking is added to each of the pmap
functions that acquire this r/w lock, its acquisition will be changed from
write to read, enabling concurrent execution of the pmap functions with
finer-grained locking.
X-MFC after: r236045
longer uses the active and inactive paging queues. Instead, the pmap now
maintains an LRU-ordered list of pv entry pages, and pmap_pv_reclaim() uses
this list to select pv entries for reclamation.
Note: The old pmap_collect() tried to avoid reclaiming mappings for pages
that have either a hold_count or a busy field that is non-zero. However,
this isn't necessary for correctness, and the locking in pmap_collect() was
insufficient to guarantee that such mappings weren't reclaimed. The new
pmap_pv_reclaim() doesn't even try.
MFC after: 5 weeks
in_cksum.h required ip.h to be included for struct ip. To be
able to use some general checksum functions like in_addword()
in a non-IPv4 context, limit the (also exported to user space)
IPv4 specific functions to the times, when the ip.h header is
present and IPVERSION is defined (to 4).
We should consider more general checksum (updating) functions
to also allow easier incremental checksum updates in the L3/4
stack and firewalls, as well as ponder further requirements by
certain NIC drivers needing slightly different pseudo values
in offloading cases. Thinking in terms of a better "library".
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
Reviewed by: gnn (as part of the whole)
MFC After: 3 days
With the changes over the past year to how accesses to the page's dirty
field are synchronized, there is no need for pmap_protect() to acquire
the page queues lock unless it is going to access the pv lists or
PMAP1/PADDR1.
Style fix to pmap_protect().
Most part is merged from amd64.
- i386/acpica/acpi_wakecode.S
Replaced with amd64 code (from realmode to paging enabling code).
- i386/acpica/acpi_wakeup.c
Replaced with amd64 code (except for wakeup_pagetables stuff).
- i386/include/pcb.h
- i386/i386/genassym.c
Added PCB new members (CR0, CR2, CR4, DS, ED, FS, SS, GDT, IDT, LDT
and TR) needed for suspend/resume, not for context switch.
- i386/i386/swtch.s
Added suspendctx() and resumectx().
Note that savectx() was not changed and used for suspending (while
amd64 code uses it).
BSP and AP execute the same sequence, suspendctx(), acpi_wakecode()
and resumectx() for suspend/resume (in case of UP system also).
- i386/i386/apic_vector.s
Added cpususpend().
- i386/i386/mp_machdep.c
- i386/include/smp.h
Added cpususpend_handler().
- i386/include/apicvar.h
- kern/subr_smp.c
- sys/smp.h
Added IPI_SUSPEND and suspend_cpus().
- i386/i386/initcpu.c
- i386/i386/machdep.c
- i386/include/md_var.h
- pc98/pc98/machdep.c
Moved initializecpu() declarations to md_var.h.
MFC after: 3 days
ataraid(4) previously was present there and having GEOM RAID is convinient.
Unlike other classes GEOM RAID can be set up from BIOS before install and
users are expecting it to be detected automatically.
- DTrace scripts to check for errors, performance, ...
they serve mostly as examples of what you can do with the static probe;s
with moderate load the scripts may be overwhelmed, excessive lock-tracing
may influence program behavior (see the last design decission)
Design decissions:
- use "linuxulator" as the provider for the native bitsize; add the
bitsize for the non-native emulation (e.g. "linuxuator32" on amd64)
- Add probes only for locks which are acquired in one function and released
in another function. Locks which are aquired and released in the same
function should be easy to pair in the code, inter-function
locking is more easy to verify in DTrace.
- Probes for locks should be fired after locking and before releasing to
prevent races (to provide data/function stability in DTrace, see the
man-page of "dtrace -v ..." and the corresponding DTrace docs).
intr_bind() on x86.
This has been requested by jhb and I strongly disagree with this,
but as long as he is the x86 and interrupt subsystem maintainer I will
follow his directives.
The disagreement cames from what we should really consider as a
public KPI. IMHO, if we really need a selection between the kernel
functions, we may need an explicit protection like _KERNEL_KPI, which
defines which subset of the kernel function might really be considered
as part of the KPI (for thirdy part modules) and which not.
As long as we don't have this mechanism I just consider any possible
function as usable by thirdy part code, thus intr_bind() included.
MFC after: 1 week
discrepancy between modules and kernel, but deal with SMP differences
within the functions themselves.
As an added bonus this also helps in terms of code readability.
Requested by: gibbs
Reviewed by: jhb, marius
MFC after: 1 week
but GNU libc used it without checking its kernel version, e. g., Fedora 10.
- Move pipe(2) implementation for Linuxulator from MD files to MI file,
sys/compat/linux/linux_file.c. There is no MD code for this syscall at all.
- Correct an argument type for pipe() from l_ulong * to l_int *. Probably
this was the source of MI/MD confusion.
Reviewed by: emulation
push the address onto stack as we do for INTn emulation. This avoids stack
underflow when we encounter RETF instruction in VM86 mode. Lack of this
exit point actually caused page fault in VM86 mode with VESA module when we
resume from suspend state[1].
- Remove unnecessary CLI and STI instructions from BIOS interrupt emulation.
INTn and IRET must be able to emulate the flag correctly.
Reported by: gavin [1]
Tested by: gavin (early revision)
MFC after: 3 days
- Mark 'sdp' as requiring 'inet'.
- Always include "opt_inet.h" and "opt_inet6.h" and modify the IB
driver Makefiles to honor WITH/WITHOUT_INET/INET6/_SUPPORT options
to determine what should be enabled during a module build.
- Fix the mlxen(4) driver and the core IB code to compile without
if INET is disabled (including when both INET and INET6 are disabled).
Reviewed by: bz
MFC after: 2 weeks
in set_apic_interrupt_ids(). Besides, set_apic_interrupts_ids() is not
called in the !SMP case too.
Fix this by:
- Adding the BSP as an interrupt target directly in cpu_startup().
- Remove an obsolete optimization where the BSP are skipped in
set_apic_interrupt_ids().
Reported by: jh
Reviewed by: jhb
MFC after: 3 days
X-MFC: r233961
Pointy hat to: me
an uncorrected ECC error tends to fire on all CPUs in a package
simultaneously and the current printf hacks are not sufficient to make
the messages legible. Instead, use the existing mca_lock spinlock to
serialize calls to mca_log() and change the machine check code to panic
directly when an unrecoverable error is encoutered rather than falling
back to a trap_fatal() call in trap() (which adds nearly a screen-full of
logging messages that aren't useful for machine checks).
MFC after: 2 weeks
bridges. Rather than blindly enabling the windows on all of them, only
enable the window when an MSI interrupt is enabled for a device behind
the bridge, similar to what already happens for HT PCI-PCI bridges.
To implement this, each x86 Host-PCI bridge driver has to be able to
locate it's actual backing device on bus 0. For ACPI, use the _ADR
method to find the slot and function of the device. For the non-ACPI
case, the legacy(4) driver already scans bus 0 looking for Host-PCI
bridge devices. Now it saves the slot and function of each bridge that
it finds as ivars that the Host-PCI bridge driver can then use in its
pcib_map_msi() method.
This fixes machines where non-MSI interrupts were broken by the previous
round of HT MSI changes.
Tested by: bapt
MFC after: 1 week
be less ambiguous and more clearly identify what it means. This
attribute is what Intel refers to as UC-, and it's only difference
relative to normal UC memory is that a WC MTRR will override a UC-
PAT entry causing the memory to be treated as WC, whereas a UC PAT
entry will always override the MTRR.
- Remove the VM_MEMATTR_UNCACHED alias from powerpc.
New kernel events can be added at various location for sampling or counting.
This will for example allow easy system profiling whatever the processor is
with known tools like pmcstat(8).
Simultaneous usage of software PMC and hardware PMC is possible, for example
looking at the lock acquire failure, page fault while sampling on
instructions.
Sponsored by: NETASQ
MFC after: 1 month
<20120222095239.Horde.0hpYHJjmRSRPRKzXsoFRbYk@webmail.leidinger.net>.
According to some private emails received, it apparently is not unpopular
to use at least Quad GigaSwift cards driven by cas(4) in x86 machines.
MFC after: 1 week
The GPL infected parts which were blocking the inclusion of snd_csa
and snd_emu10kx in GENERIC have recently been removed from the tree.
I'm also adding snd_cmi to GENERIC, which I originally intended to
add when we enabled sound support by default.
Discussed with: jhb, pfg, Yuriy Tsibizov <yuriy.tsibizov@gfk.ru>
Approved by: jhb
kernel.
When access restrictions are added to a page table entry, we flush the
corresponding virtual address mapping from the TLB. In contrast, when
access restrictions are removed from a page table entry, we do not
flush the virtual address mapping from the TLB. This is exactly as
recommended in AMD's documentation. In effect, when access
restrictions are removed from a page table entry, AMD's MMUs will
transparently refresh a stale TLB entry. In short, this saves us from
having to perform potentially costly TLB flushes. In contrast,
Intel's MMUs are allowed to generate a spurious page fault based upon
the stale TLB entry. Usually, such spurious page faults are handled
by vm_fault() without incident. However, when we are executing
no-fault sections of the kernel, we are not allowed to execute
vm_fault(). This change introduces special-case handling for spurious
page faults that occur in no-fault sections of the kernel.
In collaboration with: kib
Tested by: gibbs (an earlier version)
I would also like to acknowledge Hiroki Sato's assistance in
diagnosing this problem.
MFC after: 1 week
As of FreeBSD 8, this driver should not be used. Applications that use
posix_openpt(2) and openpty(3) use the pts(4) that is built into the
kernel unconditionally. If it turns out high profile depend on the
pty(4) module anyway, I'd rather get those fixed. So please report any
issues to me.
The pty(4) module is still available as a kernel module of course, so a
simple `kldload pty' can be used to run old-style pseudo-terminals.
segments.h to a new x86 segments.h.
Add __packed attribute to some structs (just to be sure).
Also make it clear that i386 GDT and LDT entries are used in ia64 code.
excluded from superpage promotions. At least one of the reason is
that pv_table is sized for non-fictitious pages only.
Consistently check for the page to be non-fictitious before accesing
superpage pv list.
Sponsored by: The FreeBSD Foundation
Reviewed by: alc
MFC after: 2 weeks
reg.h with stubs.
The tREGISTER macros are only made visible on i386. These macros are
deprecated and should not be available on amd64.
The i386 and amd64 versions of struct reg have been renamed to struct
__reg32 and struct __reg64. During compilation either __reg32 or __reg64
is defined as reg depending on the machine architecture. On amd64 the i386
struct is also available as struct reg32 which is used in COMPAT_FREEBSD32
code.
Most of compat/ia32/ia32_reg.h is now IA64 only.
Reviewed by: kib (previous version)
Remove FPU types from compat/ia32/ia32_reg.h that are no longer needed.
Create machine/npx.h on amd64 to allow compiling i386 code that uses
this header.
The original npx.h and fpu.h define struct envxmm differently. Both
definitions have been included in the new x86 header as struct __envxmm32
and struct __envxmm64. During compilation either __envxmm32 or __envxmm64
is defined as envxmm depending on machine architecture. On amd64 the i386
struct is also available as struct envxmm32.
Reviewed by: kib
- Merge r232744 changes to pc98.
(Allow a kernel to be built with 'nodevice atpic'.)
- Move ICU related defines from x86/isa/atpic.c to x86/isa/icu.h and
use them in x86/x86/intr_machdep.c.
Reviewed by: jhb
kernel version introduced the sysctl (based upon a linux man-page)
- add comments to sscalls.master regarding some names of sysctls which are
different than the linux-names (based upon the linux unistd.h)
- add some dummy sysctls
- name an unimplemented sysctl
MFC after: 1 month
amd64, if 'device isa' is present quiesce the 8259A's during boot and
resume from suspend.
While here, be more selective on amd64 about which kernel configurations
need elcr.c.
MFC after: 2 weeks
- Return failure for a suspend attempt if we have no wake address.
- Use intr_disable()/intr_restore() instead of ACPI_DISABLE_IRQS().
- Invoke intr_suspend() earlier and call intr_resume() if suspend
fails.
- Use pause in the loop waiting for CPU to suspend.
- Restore PAT MSR, switchtime, switchticks, and MTRRs on resume.
Reviewed by: jkim (earlier version)
MFC after: 2 weeks
platforms.
This will make every attempt to mount a non-mpsafe filesystem to the
kernel forbidden, unless it is expressely compiled with
VFS_ALLOW_NONMPSAFE option.
This patch is part of the effort of killing non-MPSAFE filesystems
from the tree.
No MFC is expected for this patch.
Winbond Super I/O chips.
With minor efforts it should be possible the extend the driver to support
further chips/revisions available from Winbond. In the simplest case
only new IDs need to be added, while different chipsets might require
their own function to enter extended function mode, etc.
Sponsored by: Sandvine Incorporated ULC (in 2011)
Reviewed by: emaste, brueffer
MFC after: 2 weeks
amd64/i386/pc98 ptrace.h with stubs.
For amd64 PT_GETXSTATE and PT_SETXSTATE have been redefined to match the
i386 values. The old values are still supported but should no longer be
used.
Reviewed by: kib
amd64/i386/pc98 endian.h with stubs.
In __bswap64_const(x) the conflict between 0xffUL and 0xffULL has been
resolved by reimplementing the macro in terms of __bswap32(x). As a side
effect __bswap64_var(x) is now implemented using two bswap instructions on
i386 and should be much faster. __bswap32_const(x) has been reimplemented
in terms of __bswap16(x) for consistency.
Vnode-backed mappings cannot be put into the kernel map, since it is a
system map.
Use exec_map for transient mappings, and remove the mappings with
kmem_free_wakeup() to notify the waiters on available map space.
Do not map the whole executable into KVA at all to copy it out into
usermode. Directly use vn_rdwr() for the case of not page aligned
binary.
There is one place left where the potentially unbounded amount of data
is mapped into exec_map, namely, in the COFF image activator
enumeration of the needed shared libraries.
Reviewed by: alc
MFC after: 2 weeks
kernel modules that include binary-only code.
More fine-grained control is provided via MK_SOURCELESS_HOST (for native code
that runs on host CPU) and MK_SOURCELESS_UCODE (for microcode).
Reviewed by: julian, delphij, freebsd-arch
Approved by: kib (mentor)
MFC after: 2 weeks
netback.c: Add missing VM includes.
xen/xenvar.h,
xen/xenpmap.h: Move some XENHVM macros from <machine/xen/xenpmap.h> to
<machine/xen/xenvar.h> on i386 to match the amd64 headers.
conf/files: Add netback to the build.
Submitted by: jhb
MFC after: 3 days
The isci driver is for the integrated SAS controller in the Intel C600
(Patsburg) chipset. Source files in sys/dev/isci directory are
FreeBSD-specific, and sys/dev/isci/scil subdirectory contains
an OS-agnostic library (SCIL) published by Intel to control the SAS
controller. This library is used primarily as-is in this driver, with
some post-processing to better integrate into the kernel build
environment.
isci.4 and a README in the sys/dev/isci directory contain a few
additional details.
This driver is only built for amd64 and i386 targets.
Sponsored by: Intel
Reviewed by: scottl
Approved by: scottl
64bit and 32bit ABIs. As a side-effect, it enables AVX on capable
CPUs.
In particular:
- Query the CPU support for XSAVE, list of the supported extensions
and the required size of FPU save area. The hw.use_xsave tunable is
provided for disabling XSAVE, and hw.xsave_mask may be used to
select the enabled extensions.
- Remove the FPU save area from PCB and dynamically allocate the
(run-time sized) user save area on the top of the kernel stack,
right above the PCB. Reorganize the thread0 PCB initialization to
postpone it after BSP is queried for save area size.
- The dumppcb, stoppcbs and susppcbs now do not carry the FPU state as
well. FPU state is only useful for suspend, where it is saved in
dynamically allocated suspfpusave area.
- Use XSAVE and XRSTOR to save/restore FPU state, if supported and
enabled.
- Define new mcontext_t flag _MC_HASFPXSTATE, indicating that
mcontext_t has a valid pointer to out-of-struct extended FPU
state. Signal handlers are supplied with stack-allocated fpu
state. The sigreturn(2) and setcontext(2) syscall honour the flag,
allowing the signal handlers to inspect and manipilate extended
state in the interrupted context.
- The getcontext(2) never returns extended state, since there is no
place in the fixed-sized mcontext_t to place variable-sized save
area. And, since mcontext_t is embedded into ucontext_t, makes it
impossible to fix in a reasonable way. Instead of extending
getcontext(2) syscall, provide a sysarch(2) facility to query
extended FPU state.
- Add ptrace(2) support for getting and setting extended state; while
there, implement missed PT_I386_{GET,SET}XMMREGS for 32bit binaries.
- Change fpu_kern KPI to not expose struct fpu_kern_ctx layout to
consumers, making it opaque. Internally, struct fpu_kern_ctx now
contains a space for the extended state. Convert in-kernel consumers
of fpu_kern KPI both on i386 and amd64.
First version of the support for AVX was submitted by Tim Bird
<tim.bird am sony com> on behalf of Sony. This version was written
from scratch.
Tested by: pho (previous version), Yamagi Burmeister <lists yamagi org>
MFC after: 1 month
CTL is a disk and processor device emulation subsystem originally written
for Copan Systems under Linux starting in 2003. It has been shipping in
Copan (now SGI) products since 2005.
It was ported to FreeBSD in 2008, and thanks to an agreement between SGI
(who acquired Copan's assets in 2010) and Spectra Logic in 2010, CTL is
available under a BSD-style license. The intent behind the agreement was
that Spectra would work to get CTL into the FreeBSD tree.
Some CTL features:
- Disk and processor device emulation.
- Tagged queueing
- SCSI task attribute support (ordered, head of queue, simple tags)
- SCSI implicit command ordering support. (e.g. if a read follows a mode
select, the read will be blocked until the mode select completes.)
- Full task management support (abort, LUN reset, target reset, etc.)
- Support for multiple ports
- Support for multiple simultaneous initiators
- Support for multiple simultaneous backing stores
- Persistent reservation support
- Mode sense/select support
- Error injection support
- High Availability support (1)
- All I/O handled in-kernel, no userland context switch overhead.
(1) HA Support is just an API stub, and needs much more to be fully
functional.
ctl.c: The core of CTL. Command handlers and processing,
character driver, and HA support are here.
ctl.h: Basic function declarations and data structures.
ctl_backend.c,
ctl_backend.h: The basic CTL backend API.
ctl_backend_block.c,
ctl_backend_block.h: The block and file backend. This allows for using
a disk or a file as the backing store for a LUN.
Multiple threads are started to do I/O to the
backing device, primarily because the VFS API
requires that to get any concurrency.
ctl_backend_ramdisk.c: A "fake" ramdisk backend. It only allocates a
small amount of memory to act as a source and sink
for reads and writes from an initiator. Therefore
it cannot be used for any real data, but it can be
used to test for throughput. It can also be used
to test initiators' support for extremely large LUNs.
ctl_cmd_table.c: This is a table with all 256 possible SCSI opcodes,
and command handler functions defined for supported
opcodes.
ctl_debug.h: Debugging support.
ctl_error.c,
ctl_error.h: CTL-specific wrappers around the CAM sense building
functions.
ctl_frontend.c,
ctl_frontend.h: These files define the basic CTL frontend port API.
ctl_frontend_cam_sim.c: This is a CTL frontend port that is also a CAM SIM.
This frontend allows for using CTL without any
target-capable hardware. So any LUNs you create in
CTL are visible in CAM via this port.
ctl_frontend_internal.c,
ctl_frontend_internal.h:
This is a frontend port written for Copan to do
some system-specific tasks that required sending
commands into CTL from inside the kernel. This
isn't entirely relevant to FreeBSD in general,
but can perhaps be repurposed.
ctl_ha.h: This is a stubbed-out High Availability API. Much
more is needed for full HA support. See the
comments in the header and the description of what
is needed in the README.ctl.txt file for more
details.
ctl_io.h: This defines most of the core CTL I/O structures.
union ctl_io is conceptually very similar to CAM's
union ccb.
ctl_ioctl.h: This defines all ioctls available through the CTL
character device, and the data structures needed
for those ioctls.
ctl_mem_pool.c,
ctl_mem_pool.h: Generic memory pool implementation used by the
internal frontend.
ctl_private.h: Private data structres (e.g. CTL softc) and
function prototypes. This also includes the SCSI
vendor and product names used by CTL.
ctl_scsi_all.c,
ctl_scsi_all.h: CTL wrappers around CAM sense printing functions.
ctl_ser_table.c: Command serialization table. This defines what
happens when one type of command is followed by
another type of command.
ctl_util.c,
ctl_util.h: CTL utility functions, primarily designed to be
used from userland. See ctladm for the primary
consumer of these functions. These include CDB
building functions.
scsi_ctl.c: CAM target peripheral driver and CTL frontend port.
This is the path into CTL for commands from
target-capable hardware/SIMs.
README.ctl.txt: CTL code features, roadmap, to-do list.
usr.sbin/Makefile: Add ctladm.
ctladm/Makefile,
ctladm/ctladm.8,
ctladm/ctladm.c,
ctladm/ctladm.h,
ctladm/util.c: ctladm(8) is the CTL management utility.
It fills a role similar to camcontrol(8).
It allow configuring LUNs, issuing commands,
injecting errors and various other control
functions.
usr.bin/Makefile: Add ctlstat.
ctlstat/Makefile
ctlstat/ctlstat.8,
ctlstat/ctlstat.c: ctlstat(8) fills a role similar to iostat(8).
It reports I/O statistics for CTL.
sys/conf/files: Add CTL files.
sys/conf/NOTES: Add device ctl.
sys/cam/scsi_all.h: To conform to more recent specs, the inquiry CDB
length field is now 2 bytes long.
Add several mode page definitions for CTL.
sys/cam/scsi_all.c: Handle the new 2 byte inquiry length.
sys/dev/ciss/ciss.c,
sys/dev/ata/atapi-cam.c,
sys/cam/scsi/scsi_targ_bh.c,
scsi_target/scsi_cmds.c,
mlxcontrol/interface.c: Update for 2 byte inquiry length field.
scsi_da.h: Add versions of the format and rigid disk pages
that are in a more reasonable format for CTL.
amd64/conf/GENERIC,
i386/conf/GENERIC,
ia64/conf/GENERIC,
sparc64/conf/GENERIC: Add device ctl.
i386/conf/PAE: The CTL frontend SIM at least does not compile
cleanly on PAE.
Sponsored by: Copan Systems, SGI and Spectra Logic
MFC after: 1 month
It seems strchr() and strrchr() are used more often than index() and
rindex(). Therefore, simply migrate all kernel code to use it.
For the XFS code, remove an empty line to make the code identical to
the code in the Linux kernel.
are booting inside a VM. There are three reasons to disable this:
o It causes the VM host to believe that all the tested pages or RAM are
in use. This in turn may force the host to page out pages of RAM
belonging to other VMs, or otherwise cause problems with fair resource
sharing on the VM cluster.
o It adds significant time to the boot process (around 1 second/Gig in
testing)
o It is unnecessary - the host should have already verified that the
memory is functional etc.
Note that this simply changes the default when in a VM - it can still be
overridden using the hw.memtest.tests tunable.
MFC after: 4 weeks
When r207410 eliminated the acquisition and release of the page queues
lock from pmap_extract_and_hold(), it didn't take into account that
pmap_pte_quick() sometimes requires the page queues lock to be held.
This change reimplements pmap_extract_and_hold() such that it no
longer uses pmap_pte_quick(), and thus never requires the page queues
lock.
Merge r177525 from the native pmap
Prevent the overflow in the calculation of the next page directory.
The overflow causes the wraparound with consequent corruption of the
(almost) whole address space mapping.
Strictly speaking, r177525 is not required by the Xen pmap because the
hypervisor steals the uppermost region of the normal kernel address
space. I am nonetheless merging it in order to reduce the number of
unnecessary differences between the native and Xen pmap implementations.
Tested by: sbruno
configurations for various architectures in FreeBSD 10.x. This allows
basic Capsicum functionality to be used in the default FreeBSD
configuration on non-embedded architectures; process descriptors are not
yet enabled by default.
MFC after: 3 months
Sponsored by: Google, Inc
