PAE to insta-panic on startup. Remove one unused variable that was
commented out.
Reviewed by: ambrisko@
Obtained from: jhb@ peter@ bz@ and countless others during BSDCAN
MFC after: 3 days
them to cleanup and goto out when acknowledging the LD's. Check
for failure on malloc. Remove a couple of extra lines and remove
the spurious return.
Prompted by: Petr Lampa
MFC after: 3 days
ThunderBolt cannot read sector >= 2^32 or 2^21
with supplied patch.
Second the bigger change, fix RAID operation on ThunderBolt base
card such as physically removing a disk from a RAID and replacing
it. The current situation is the RAID firmware effectively hangs
waiting for an acknowledgement from the driver. This is due to
the firmware support of the driver actually accessing the RAID
from under the firmware. This is an interesting feature that
the FreeBSD driver does not use. However, when the firmare
detects the driver has attached it then expects the driver will
synchronize LD's with the firmware. If the driver does not sync.
then the management part of the firmware will hang waiting for
it so a pulled driver will listed as still there.
The fix for this problem isn't extremely difficult. However,
figuring out why some of the code was the way it was and then
redoing it was involved. Not have a spec. made it harder to
try to figure out. The existing driver would send a
MFI_DCMD_LD_MAP_GET_INFO command in write mode to acknowledge
a LD state change. In read mode it gets the RAID map from the
firmware. The FreeBSD driver doesn't do that currently. It
could be added in the future with the appropriate structures.
To simplify things, get the current LD state and then build
the MFI_DCMD_LD_MAP_GET_INFO/write command so that it sends
an acknowledgement for each LD. The map would probably state
which LD's changed so then the driver could probably just
acknowledge the LD's that changed versus all. This doesn't seem
to be a problem. When a MFI_DCMD_LD_MAP_GET_INFO/write command
is sent to the firmware, it will complete later when a change
to the LD's happen. So it is very much like an AEN command
returning when something happened. When the
MFI_DCMD_LD_MAP_GET_INFO/write command completes, we refire the
sync'ing of the LD state. This needs to be done in as an event
so that MFI_DCMD_LD_GET_LIST can wait for that command to
complete before issuing the MFI_DCMD_LD_MAP_GET_INFO/write.
The prior code didn't use the call-back function and tried
to intercept the MFI_DCMD_LD_MAP_GET_INFO/write command when
processing an interrupt. This added a bunch of code complexity
to the interrupt handler. Using the call-back that is done
for other commands got rid of this need. So the interrupt
handler is greatly simplified. It seems that even commands
that shouldn't be acknowledged end up in the interrupt handler.
To deal with this, code was added to check to see if a command
is in the busy queue or not. This might have contributed to the
interrupt storm happening without MSI enabled on these cards.
Note that MFI_DCMD_LD_MAP_GET_INFO/read returns right away.
It would be interesting to see what other complexity could
be removed from the ThunderBolt driver that really isn't
needed in our mode of operation. Letting the RAID firmware
do all of the I/O to disks is a lot faster since it can
use its caches. It greatly simplifies what the driver has
to do and potential bugs if the driver and firmware are
not in sync.
Simplify the aen_abort/cm_map_abort and put it in the softc
versus in the command structure.
This should get merged to 9 before the driver is merged to
8.
PR: 167226
Submitted by: Petr Lampa
MFC after: 3 days
First cut of new HW support from LSI and merge into FreeBSD.
Supports Drake Skinny and ThunderBolt cards.
MFhead_mfi r227574
Style
MFhead_mfi r227579
Use bus_addr_t instead of uintXX_t.
MFhead_mfi r227580
MSI support
MFhead_mfi r227612
More bus_addr_t and remove "#ifdef __amd64__".
MFhead_mfi r227905
Improved timeout support from Scott.
MFhead_mfi r228108
Make file.
MFhead_mfi r228208
Fixed botched merge of Skinny support and enhanced handling
in call back routine.
MFhead_mfi r228279
Remove superfluous !TAILQ_EMPTY() checks before TAILQ_FOREACH().
MFhead_mfi r228310
Move mfi_decode_evt() to taskqueue.
MFhead_mfi r228320
Implement MFI_DEBUG for 64bit S/G lists.
MFhead_mfi r231988
Restore structure layout by reverting the array header to
use [0] instead of [1].
MFhead_mfi r232412
Put wildcard pattern later in the match table.
MFhead_mfi r232413
Use lower case for hexadecimal numbers to match surrounding
style.
MFhead_mfi r232414
Add more Thunderbolt variants.
MFhead_mfi r232888
Don't act on events prior to boot or when shutting down.
Add hw.mfi.detect_jbod_change to enable or disable acting
on JBOD type of disks being added on insert and removed on
removing. Switch hw.mfi.msi to 1 by default since it works
better on newer cards.
MFhead_mfi r233016
Release driver lock before taking Giant when deleting children.
Use TAILQ_FOREACH_SAFE when items can be deleted. Make code a
little simplier to follow. Fix a couple more style issues.
MFhead_mfi r233620
Update mfi_spare/mfi_array with the actual number of elements
for array_ref and pd. Change these max. #define names to avoid
name space collisions. This will require an update to mfiutil
It avoids mfiutil having to do a magic calculation.
Add a note and #define to state that a "SYSTEM" disk is really
what the firmware calls a "JBOD" drive.
Thanks to the many that helped, LSI for the initial code drop,
mav, delphij, jhb, sbruno that all helped with code and testing.
one. Interestingly, these are actually the default for quite some time
(bus_generic_driver_added(9) since r52045 and bus_generic_print_child(9)
since r52045) but even recently added device drivers do this unnecessarily.
Discussed with: jhb, marcel
- While at it, use DEVMETHOD_END.
Discussed with: jhb
- Also while at it, use __FBSDID.
can be enabled via the hw.mfi.msi tunable. Many mfi(4) controllers also
support MSI-X, but in testing it seems that many adapters do not work with
MSI-X but do work with MSI.
MFC after: 2 weeks
ensuring that everything is really, truly consistent.
This fixes certain cases where one will see various:
mfi0: COMMAND 0xffffffXXXXXXXXXX TIMEOUT AFTER XX SECONDS
MFC after: 3 days
Submitted by: scottl
Ok'ed by: jhb
The SYSCTL_NODE macro defines a list that stores all child-elements of
that node. If there's no SYSCTL_DECL macro anywhere else, there's no
reason why it shouldn't be static.
Specifically, add support for "Drake Skinny" and "ThunderBolt" LSI
cards.
Initial code was supplied by LSI under BSD license. Several improvements
were done by myself. Such things like making it work in a static kernel,
be able to boot of the RAID, performance improvements. I removed some
fairly complicated code that seemed to directly access the disks under
the firmware. It doesn't seem to be needed and significantly slowed
down the performance of the driver and caused tons of sense errors to
be reported.
This code is being checked in this area so others can help me get it into
shape to commit into the FreeBSD tree. Assistance has been volunteered
by iXsystems.
We might want to re-work the JBOD attachment that creates /dev/mfisyspd?
node for each disk.
Performance is faster then prior cards. It works okay with WITNESS
and INVARIANTS on amd64 and i386. I recall seeing a use after
free time bug with FreeBSD 8 and a Drake Skinny card with WITNESS
and INVARIANTS on.
First task is get all of the new structures to be named in FreeBSD
style format.
Next is probably to deal with the 64bit addressing changes that are
mostly around the #ifdef __amd64__ checks.
Thanks to LSI for providing the initial code.
Obtained from: LSI
to an API change in CAM. It's once again possible to link a static kernel
with 'mfi' without requiring 'scbus' as well. Ditto for KLD loading.
Submitted by: kib
Reviewed by: ken
MFC after: 3 days
by present MegaCLI version. It has some special meaning for the first s/g
list entry, while the main s/g list begins from the the second entry, and
those lists should remain separate after loading to the busdma map.
- Fix bug in 32bit ioctl compatibility shims when s/g list consists of
more then on element.
Sponsored by: iXsystems, inc.
MFC after: 3 days
patch modifies makesyscalls.sh to prefix all of the non-compatibility
calls (e.g. not linux_, freebsd32_) with sys_ and updates the kernel
entry points and all places in the code that use them. It also
fixes an additional name space collision between the kernel function
psignal and the libc function of the same name by renaming the kernel
psignal kern_psignal(). By introducing this change now we will ease future
MFCs that change syscalls.
Reviewed by: rwatson
Approved by: re (bz)
kernel for FreeBSD 9.0:
Add a new capability mask argument to fget(9) and friends, allowing system
call code to declare what capabilities are required when an integer file
descriptor is converted into an in-kernel struct file *. With options
CAPABILITIES compiled into the kernel, this enforces capability
protection; without, this change is effectively a no-op.
Some cases require special handling, such as mmap(2), which must preserve
information about the maximum rights at the time of mapping in the memory
map so that they can later be enforced in mprotect(2) -- this is done by
narrowing the rights in the existing max_protection field used for similar
purposes with file permissions.
In namei(9), we assert that the code is not reached from within capability
mode, as we're not yet ready to enforce namespace capabilities there.
This will follow in a later commit.
Update two capability names: CAP_EVENT and CAP_KEVENT become
CAP_POST_KEVENT and CAP_POLL_KEVENT to more accurately indicate what they
represent.
Approved by: re (bz)
Submitted by: jonathan
Sponsored by: Google Inc
These cause problems when trying to include the header in a C++ project.
Rename them to 'evt_class', and track the change in mfi and mfiutil.
Submitted by: Mark Johnston
Sponsored by: Sandvine Incorporated
Reviewed by: jhb@
MFC after: 1 week
preserve the upper bits of the first data byte.
While here, shorten a few nearby lines.
PR: kern/152768
Reported by: Sascha Wildner saw of online.de
Reviewed by: scottl
MFC after: 1 week
controllers. Controller, array, and drive status can be checked, basic
attributes can be changed, and arrays and spares can be created and deleted.
Controller firmware can also be flashed.
This does not replace MegaCLI, found in ports, as that is officially sanctioned
and supported by LSI and includes vastly more functionality. However, mfiutil
is open source and guaranteed to provide basic functionality, which can be
especially useful if you have a problem and can't get MegaCLI to work.
Approved by: re
Obtained from: Yahoo! Inc.
The newbus lock is responsible for protecting newbus internIal structures,
device states and devclass flags. It is necessary to hold it when all
such datas are accessed. For the other operations, softc locking should
ensure enough protection to avoid races.
Newbus lock is automatically held when virtual operations on the device
and bus are invoked when loading the driver or when the suspend/resume
take place. For other 'spourious' operations trying to access/modify
the newbus topology, newbus lock needs to be automatically acquired and
dropped.
For the moment Giant is also acquired in some key point (modules subsystem)
in order to avoid problems before the 8.0 release as module handlers could
make assumptions about it. This Giant locking should go just after
the release happens.
Please keep in mind that the public interface can be expanded in order
to provide more support, if there are really necessities at some point
and also some bugs could arise as long as the patch needs a bit of
further testing.
Bump __FreeBSD_version in order to reflect the newbus lock introduction.
Reviewed by: ed, hps, jhb, imp, mav, scottl
No answer by: ariff, thompsa, yongari
Tested by: pho,
G. Trematerra <giovanni dot trematerra at gmail dot com>,
Brandon Gooch <jamesbrandongooch at gmail dot com>
Sponsored by: Yahoo! Incorporated
Approved by: re (ksmith)
modularize it so that new transports can be created.
Add a transport for SATA
Add a periph+protocol layer for ATA
Add a driver for AHCI-compliant hardware.
Add a maxio field to CAM so that drivers can advertise their max
I/O capability. Modify various drivers so that they are insulated
from the value of MAXPHYS.
The new ATA/SATA code supports AHCI-compliant hardware, and will override
the classic ATA driver if it is loaded as a module at boot time or compiled
into the kernel. The stack now support NCQ (tagged queueing) for increased
performance on modern SATA drives. It also supports port multipliers.
ATA drives are accessed via 'ada' device nodes. ATAPI drives are
accessed via 'cd' device nodes. They can all be enumerated and manipulated
via camcontrol, just like SCSI drives. SCSI commands are not translated to
their ATA equivalents; ATA native commands are used throughout the entire
stack, including camcontrol. See the camcontrol manpage for further
details. Testing this code may require that you update your fstab, and
possibly modify your BIOS to enable AHCI functionality, if available.
This code is very experimental at the moment. The userland ABI/API has
changed, so applications will need to be recompiled. It may change
further in the near future. The 'ada' device name may also change as
more infrastructure is completed in this project. The goal is to
eventually put all CAM busses and devices until newbus, allowing for
interesting topology and management options.
Few functional changes will be seen with existing SCSI/SAS/FC drivers,
though the userland ABI has still changed. In the future, transports
specific modules for SAS and FC may appear in order to better support
the topologies and capabilities of these technologies.
The modularization of CAM and the addition of the ATA/SATA modules is
meant to break CAM out of the mold of being specific to SCSI, letting it
grow to be a framework for arbitrary transports and protocols. It also
allows drivers to be written to support discrete hardware without
jeopardizing the stability of non-related hardware. While only an AHCI
driver is provided now, a Silicon Image driver is also in the works.
Drivers for ICH1-4, ICH5-6, PIIX, classic IDE, and any other hardware
is possible and encouraged. Help with new transports is also encouraged.
Submitted by: scottl, mav
Approved by: re
- Fix to ioctl path in which the length could be 0 which means
no data in/out from LSI.
- Fix to ioctl path in which the data in the sense data space
of the ioctl packet is a really a pointer to some location in
user-space. From LSI re-worked a bit by me.
- Add HW support for next gen cards from LSI.
Thanks to LSI for their support!
Submitted by: jhb, LSI
MFC after: 3 days
- Each log entry contains a text description in the "description" field of
the entry. The existing decode logic always ended up duplicating
information that was already in the description string. This made the
logs overly verbose. Now we just print out the description string.
- Add some simple parsing of the timestamp and event classes.
Reviewed by: ambrisko, scottl
MFC after: 2 weeks
- Fetch events from the controller in batches of 15 rather than a single
event at a time.
- When fetching events from the controller, honor the event class and
locale settings (via hw.mfi tunables). This also allows the firmware to
skip over unwanted log entries resulting in fewer requests to the
controller if there many unwanted log entries since the last clean
shutdown.
- Don't drop the driver mutex while decoding an event.
- If we get an error other than MFI_STAT_NOT_FOUND (basically EOF for
hitting the end of the event log) then emit a warning and bail on
processing further log entries.
Reviewed by: ambrisko, scottl
MFC after: 2 weeks
on amd64. Note the only difference is the iovec32 part so I use the
native structure for everything else.
Also I plan to MFC all the changes in -current to 7-stable and 6-stable
shortly since I've been running them. This does not include the cam
changes.
MFC after: 3 days
down some DCMD's without any data. Thanks to Dell and LSI for helping
to provide clues to figure out this problem. Now MegaCli can upgrade
the firmware and should work identical when run on Linux.
Reviewed by: scottl, LSI
MFC after: 1 day
is actually a circular log. Deal with it rolling around. Fortunately,
the log area is big and I haven't seen any roll over yet. Update and
get rid of the obsolete comment.
- Don't leak the config lock if detach() fails due to the controller char
dev being open.
- Close a race between detach() and a process opening the controller char
dev.
MFC after: 1 week
Approved by: re (bmah)
now takes a device_t to be the parent of the bus that is being created.
Most SIMs have been updated with a reasonable argument, but a few exceptions
just pass NULL for now. This argument isn't used yet and the newbus
integration likely won't be ready until after 7.0-RELEASE.
- In the ioctl path let command get queued up and return
when complete _without_ blocking the driving waiting for
the response. This way the driver doesn't "lock up" for
~30s during a flash command. Submitted by scottl.
- Add a guard so that if a DCMD of 0 is sent down the ioctl
path don't send it to the controller. Return with a
status of OK. This is a little strange since MegaCli
doesn't seem to like something and will issue some DCMD
of 0. This doesn't happen under Linux. So the emulation
needs to be improved but I'm not sure what. Another strange
thing is that when a DCMD of 0 gets issued under i386 the
controller returns OK but in amd64 the context is messed
up.
- Add a guard so the context has to be with-in the legal
limit so we get a reasonable error assertion versus random
panic.
It's going to be a challenge to figure out why MegaCli is not totally
happy and then sends some bogus commands. This means that flashing
firmware via the Linux tool won't work since it generates a DCMD of
0 when it should be opening the firmware for a flash update. Without
this problem flashing works fine. This means there is no publicly
available tool to upgrade the RAID firmware under FreeBSD right now.
I plan to MFC all of the mfi changes to 6.X shortly. This might not
include the SCSI pass-through changes.
Submitted by: scottl
Reviewed by: scottl
MFC after: 3 days
1) s/mi/mfi/ in FreeBSD ioctl path
2) add in "\n" on various failure messages
3) cap the length of time to abort an AEN command
4) fix passing sense data back to user to make Dell's Linux firmware
upgrade tool happy.
5) bump the MFI_POLL_TIMEOUT_SECS from 10s to 50s since the
firmware flash command can take ~40s to return.
This is some clean-up and enables RAID firmware to updated via Dell's
tool. Note Dell's tool requires the updates to the Linux emulator
that has been done in -current with TLS etc.
I need to discuss with scottl how to better submit mfi commands to
the firmware via the ioctl path so we don't do it in polled mode.
after calling mfi_mapcmd is no longer needed, so long as the MFI_CMD_POLLED
flag is set. This change eliminates the possibility of a polled command
getting posted twice to the driver. This is turn fixes panics on shutdown
when INVARIANTS is set.
Sponsored by: Ironport
- Add a translation so the Linux ioctl's don't conflict with
the FreeBSD definition.
- Assume Linux 32bit emulation on amd64.
This was tested on i386 and amd64 with the 32bit Linux MegaCli.
Eventually we should do a 32bit native FreeBSD translation app.
- Fix the locking protocol to eliminate races between normal I/O and AENs.
- Various small improvements and usability tweaks.
Sponsored by: IronPort
Portions Submitted by: Doug Ambrisko
AEN. This makes the boot messages cleaner. I now know how this
structure works so I can implement it versus guessing. Remove the
not ready type code since it is ready now.
I added the time stamp/locale/class so people can parse messages better.
Create a sysctl so that we can set the locale/class level.
the description so we don't have to do any more queries. Disable the
event query code until it figured out since but it is similar to the
AEN detail so we should be able to get that working.
- Linux ioctl support, with the other Linux changes MegaCli
will run if you mount linprocfs & linsysfs then set
sysctl compat.linux.osrelease=2.6.12 or similar. This works
on i386. It should work on amd64 but not well tested yet.
StoreLib may or may not work. Remember to kldload mfi_linux.
- Add in AEN (Async Event Notification) support so we can
get messages from the firmware when something happens.
Not all messages are in defined in event detail. Use
event_log to try to figure out what happened.
- Try to implement something like SIGIO for StoreLib. Since
mrmonitor doesn't work right I can't fully test it. StoreLib
works best with the rh9 base. In theory mrmonitor isn't
needed due to native driver support of AEN :-)
Now we can configure and monitor the RAID better.
Submitted by: IronPort Systems.
Saab for helping to track this down. Fix a error with 32bit DMA size
calculation that seemed to be harmless. Add a few micro-optimizations while
I'm here.
is derived from the phrase 'MegaRAID Firmware Interface' used by LSI. This
driver provides a block interface to logical disks on the card and a minimal
management device. It is MPSAFE, INTR_FAST, and 64-bit capable.
Thanks to Dell for providing hardware to test with and IronPort for
sponsoring the work.
Sponsored by: Dell, Ironport
MFC After: 3 days
