unconventionally:
If COMPAT_IPFW is not defined, or if it is defined to 1, enable;
otherwise, disable.
This means that these changes actually have no effect on anyone at the
moment. (It just makes it easier for me to keep my code in sync.)
In the future, the `not defined' part of the hack should be eliminated,
but doing this now would require everyone to change their config files.
The same conditionals need to be made in ip_input.c as well for this to
ave any useful effect, but I'm not ready to do that right now.
call of ahc_scsirate. Otherwise, the proper setting may not get set until
the next reconnection/selection.
The saved_queue used to re-order the QINFIFO during error recovery or
certain SCB paging operations should be an array of u_chars not ints.
saved_queue type error pointed out by: Noriyuki Soda <soda@sra.co.jp>
been loaded, look for a match by device and inode number if the
traditional pathname comparisons don't find a match. This detects
the case in which a library is requested using two different names
which are really links to the same file, and avoids loading it
twice.
Requested by: peter@freebsd.org
Reviewed by: peter@freebsd.org
comparing the PTD pointers, they needed to be masked by PG_FRAME, and
they weren't. Also, the "improved" non-386 code wasn't really an
improvement, so I simplified and fixed the code. This might have
caused some of the panics caused by the VM megacommit.
I spent the better part of a day trying to figure out why my
experiment didn't work the way I expected, only to find out that
the router was dropping huge numbers of packets because of PCI bus
priblems. This does not fix the bug that errors are counted as
input packets because my patch doesn't apply cleanly.
to use the full range of settings from 3.6-20MHz on any target.
Remove all Ultra settings except for the top three that are documented
to work. This fixes some problem reports with the last revision of the
driver since at least the 5.7MHz entry doesn't work in Ultra mode.
you still need tohave done a make world and have made 'sysinstall'
this should not interfere with existing code as it's standalone.
write_mfs_in_kernel.c is duplicated alsewhere.. one will go ..
With this fix from Stephen, we are getting the target fork performance
that I have been trying to attain: P5-166, before the mega-commit: 700-800usecs,
after: 600usecs, with Stephen's fix: 500usecs!!! Also, this could be the
solution of some strange panic problems...
Reviewed by: dyson@freebsd.org
Submitted by: Stephen McKay <syssgm@devetir.qld.gov.au>
snuck in accidentally from the DARTNet kernel. SIOC*RTINFO were an
extended interface to the stock routing table and SIOCGETVIFINF was
an interface for rsvpd to ask the kernel for the list of multicast vif's.
Pointed-out-by: Brian Reichert <reichert@internet.com>
/etc/weekly is run?
Rebuilding locate database: stty: stdin isn't a terminal TERM: Undefined
variable.
'su' apparently runs in root's environment before doing a seteuid(), so
it reads root's .cshrc. The problem lies in the fact that $prompt is
*always* set by the time the command is executed, so you can't protect
your interactive commands from the non-interactive commands by the
normal:
if ($?prompt) then
# interactive stuff here
endif
Set the -f flag (su -fm) which causes it not to read root's .cshrc file,
since there should be no reason to do so for these scripts since
/etc/crontab sets up all of the necessary environment.
is enabled by having an "device ed0 at isa? [...]" config line.
The first PCI card will get a unit number one higher than the highest
defined for any ISA card of the ED type, e.g. if ed0 and ed1 are
configured, then the PCI cards will be ed2, ed3, ...
BEWARE: If you have configured your kernel as ed0 with the port address
as assigned by the PCI BIOS, then your card will be found by both the
PCI and ISA probes, and bad things may happen. Make sure to restore
the original port address form the GENERIC kernel for the ed0 device!
Reviewed by: davidg
contributions or ideas from Stephen McKay <syssgm@devetir.qld.gov.au>,
Alan Cox <alc@cs.rice.edu>, David Greenman <davidg@freebsd.org> and me:
More usage of the TAILQ macros. Additional minor fix to queue.h.
Performance enhancements to the pageout daemon.
Addition of a wait in the case that the pageout daemon
has to run immediately.
Slightly modify the pageout algorithm.
Significant revamp of the pmap/fork code:
1) PTE's and UPAGES's are NO LONGER in the process's map.
2) PTE's and UPAGES's reside in their own objects.
3) TOTAL elimination of recursive page table pagefaults.
4) The page directory now resides in the PTE object.
5) Implemented pmap_copy, thereby speeding up fork time.
6) Changed the pv entries so that the head is a pointer
and not an entire entry.
7) Significant cleanup of pmap_protect, and pmap_remove.
8) Removed significant amounts of machine dependent
fork code from vm_glue. Pushed much of that code into
the machine dependent pmap module.
9) Support more completely the reuse of already zeroed
pages (Page table pages and page directories) as being
already zeroed.
Performance and code cleanups in vm_map:
1) Improved and simplified allocation of map entries.
2) Improved vm_map_copy code.
3) Corrected some minor problems in the simplify code.
Implemented splvm (combo of splbio and splimp.) The VM code now
seldom uses splhigh.
Improved the speed of and simplified kmem_malloc.
Minor mod to vm_fault to avoid using pre-zeroed pages in the case
of objects with backing objects along with the already
existant condition of having a vnode. (If there is a backing
object, there will likely be a COW... With a COW, it isn't
necessary to start with a pre-zeroed page.)
Minor reorg of source to perhaps improve locality of ref.
This covers the security problem descibed in SA-96:10 and Jeff says that
when we upgrade to Lite2 (which fixes this problem), mount no longer needs
to be setuid, so we'll never be going back.
Submitted by: hsu
Reviewed by: pst
