- Unify bus reset/probe sequence. Whenever bus attached at boot or later,
CAM will automatically reset and scan it. It allows to remove duplicate
code from many drivers.
- Any bus, attached before CAM completed it's boot-time initialization,
will equally join to the process, delaying boot if needed.
- New kern.cam.boot_delay loader tunable should help controllers that
are still unable to register their buses in time (such as slow USB/
PCCard/ CardBus devices), by adding one more event to wait on boot.
- To allow synchronization between different CAM levels, concept of
requests priorities was extended. Priorities now split between several
"run levels". Device can be freezed at specified level, allowing higher
priority requests to pass. For example, no payload requests allowed,
until PMP driver enable port. ATA XPT negotiate transfer parameters,
periph driver configure caching and so on.
- Frozen requests are no more counted by request allocation scheduler.
It fixes deadlocks, when frozen low priority payload requests occupying
slots, required by higher levels to manage theit execution.
- Two last changes were holding proper ATA reinitialization and error
recovery implementation. Now it is done: SATA controllers and Port
Multipliers now implement automatic hot-plug and should correctly
recover from timeouts and bus resets.
- Improve SCSI error recovery for devices on buses without automatic sense
reporting, such as ATAPI or USB. For example, it allows CAM to wait, while
CD drive loads disk, instead of immediately return error status.
- Decapitalize diagnostic messages and make them more readable and sensible.
- Teach PMP driver to limit maximum speed on fan-out ports.
- Make boot wait for PMP scan completes, and make rescan more reliable.
- Fix pass driver, to return CCB to user level in case of error.
- Increase number of retries in cd driver, as device may return several UAs.
from standard 3G wireless units by supplying a raw IP/IPv6 endpoint rather than
using PPP over serial. uhsoctl(1) is used to initiate and close the WAN
connection.
Obtained from: Fredrik Lindberg <fli@shapeshifter.se>
command in the usb_msctest routines, as well as a general tidyup.
This now properly ejects the ZTE MF636, Option Gi0322 and Novatel MC950D
devices I have on my desk.
perform a function such as ejecting a 3G autoinstaller disk. The eventhandler
system properly tracks threads and is safe to unload, remove the
setting/clearing of a function pointer in the kernel by u3g(4) which included a
tsleep for safety.
management over the data endpoint causes communication to die.
Take this one step further and model it on the existing NetBSD quirk and import
other device IDs from them.
Obtained from: NetBSD
baseline subtraction, and are very temperature sensitive, so would slowly
drift out of a calibrated state when under load. Escape this by taking
the last frame before we decide that the pad is idle as a finger-free
baseline.
Tested on: iBook G4
message has been printed is enough to get someones attention. Also remove the
line number for DPRINTF/DPRINTFN, it already prints the funtion name and a
unique message.
Some EHCI chips from VIA / ATI seem to trigger interrupts before writing back
the qTD status, or miss signalling occasionally under heavy load. If the host
machine is too fast, we can miss transaction completion - when we scan the
active list the transaction still seems to be active. This generally exhibits
itself as a umass stall that never recovers.
We work around this behaviour by setting up this callback after any softintr
that completes with transactions still pending, giving us another chance to
check for completion after the writeback has taken place
Submitted by: Alexander Nedotsuko
MFC after: 3 days
- Don't write actual length if the actual length pointer is NULL [2]
- correct Linux Compatibility error codes for short isochronous IN transfers
and make status field signed.
Submitted by: Leunam Elebek [1], Manuel Gebele [2]
has been yanked, this works around a cam recounting bug when
CAM_DEV_UNCONFIGURED is set late in the detach. In certain conditions the
reference to the XPT device would not be released which would cause the usb
explore thread to sleep forever on "simfree", preventing any new usb devices to
be found/ejected on the bus.
This is intended to be a quick workaround to the problem without touching CAM
so it can be merged to 8.0.
Suggested by: mav
MFC after: 3 days
was major changes to initialize RF chipset and set H/W registers and
removed a lot of magic numbers on code. Details are as follows:
- uses the endpoint 0x89 to get TX status information which used to
get TX complete or retry numbers or get a beacon interrupt. It's
only valuable for RTL8187B.
- removes urtw_write[8|16|32]_i functions that it's useless now.
- uses ic->ic_updateslot to set SLOT, SIFS, DIES, EIFS, CW_VAL
registers that doesn't set these whenever the channel is changed.
- code for initializing RF chipset for RTL8187B changed a lot that
there was many problems on TX transfers so it doesn't work properly
even if just for a ping/pong. Now it becomes more stable than
before that TX throughputs using netperf(1) were about 15 ~ 17Mbps/s
though sometimes it encounters packet losses.
- removes a lot of magic numbers that in the previous all of
representing RX and TX descriptors were consisted of magic numbers
and structures. It'd be more readable rather than before.
- calculates TX duration more accurately for urtw(4) devices.
- style(9)
all host controllers at the same time, we avoid problems where the BIOS will
actually write to the USB registers of all the USB host controllers every time
we handover one of them, and consequently reset the OS programmed values.
Submitted by: avg
Reviewed by: jhb
Sun Type 6 USB keyboard support added in rev 1.46 conflicted with
some scan codes used in Japanese keyboards because the scan code
conversion routine was ambiguous for the overlapped codes.
PR: ports/134005
Submitted by: YAMASHIRO Jun
The EHCI HW can use the qtd_next field instead of qtd_altnext when a short
packet is received. This contradicts what is stated in the EHCI datasheet.
Also the total-bytes field in the status field of the following TD gets
corrupted upon reception of a short packet! We work this around in software by
not queueing more than one job/TD at a time of up to 16Kbytes! The bug has been
seen on multiple INTEL based EHCI chips. Other vendors have not been tested
yet.
- Applications using /dev/usb/X.Y.Z, where Z is non-zero are affected, but not
applications using LibUSB v0.1, v1.2 and v2.0.
- Mass Storage (umass) is affected.
Submitted by: Hans Petter Selasky
MFC after: 3 days
- Add quirk for ATI SB600 and SB700 to free SMB controller
- Correct schedule sleep time to 10us on the VIA ehci controller
Reported by: Dorian B<FC>ttner, Andriy Gapon
Submitted by: Hans Petter Selasky
