Examples of depecrated algorithms in manual pages and sample configs
are updated where relevant. I removed the one example of combining
ESP and AH (vs using a cipher and auth in ESP) as RFC 8221 says this
combination is NOT RECOMMENDED.
Specifically, this removes support for the following ciphers:
- des-cbc
- 3des-cbc
- blowfish-cbc
- cast128-cbc
- des-deriv
- des-32iv
- camellia-cbc
This also removes support for the following authentication algorithms:
- hmac-md5
- keyed-md5
- keyed-sha1
- hmac-ripemd160
Reviewed by: cem, gnn (older verisons)
Relnotes: yes
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D24342
RFC 8221 does not outright ban 3des as the algorithms deprecated for
13 in r348205, but it is listed as a SHOULD NOT and will likely be a
MUST NOT by the time 13 ships.
Discussed with: bjk
MFC after: 1 week
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D24341
Add some prose and a diagram describing the layout of the cipher IV
for AES-CTR and AES-GCM and how it relates to the ESP IV stored in the
packet after the ESP header. Also, remove an XXX comment about the
initial block counter value used for AES-CTR in esp_output as the
current code matches the RFC (and the equivalent code in esp_input
didn't have the XXX comment).
Discussed with: cem
This is the only place that uses CRYPTO_F_IV_GENERATE. All crypto
drivers currently duplicate the same boilerplate code to handle this
case. Doing the generation directly removes complexity from drivers.
It also simplifies support for separate input and output buffers.
Reviewed by: cem
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D24449
- The linked list of cryptoini structures used in session
initialization is replaced with a new flat structure: struct
crypto_session_params. This session includes a new mode to define
how the other fields should be interpreted. Available modes
include:
- COMPRESS (for compression/decompression)
- CIPHER (for simply encryption/decryption)
- DIGEST (computing and verifying digests)
- AEAD (combined auth and encryption such as AES-GCM and AES-CCM)
- ETA (combined auth and encryption using encrypt-then-authenticate)
Additional modes could be added in the future (e.g. if we wanted to
support TLS MtE for AES-CBC in the kernel we could add a new mode
for that. TLS modes might also affect how AAD is interpreted, etc.)
The flat structure also includes the key lengths and algorithms as
before. However, code doesn't have to walk the linked list and
switch on the algorithm to determine which key is the auth key vs
encryption key. The 'csp_auth_*' fields are always used for auth
keys and settings and 'csp_cipher_*' for cipher. (Compression
algorithms are stored in csp_cipher_alg.)
- Drivers no longer register a list of supported algorithms. This
doesn't quite work when you factor in modes (e.g. a driver might
support both AES-CBC and SHA2-256-HMAC separately but not combined
for ETA). Instead, a new 'crypto_probesession' method has been
added to the kobj interface for symmteric crypto drivers. This
method returns a negative value on success (similar to how
device_probe works) and the crypto framework uses this value to pick
the "best" driver. There are three constants for hardware
(e.g. ccr), accelerated software (e.g. aesni), and plain software
(cryptosoft) that give preference in that order. One effect of this
is that if you request only hardware when creating a new session,
you will no longer get a session using accelerated software.
Another effect is that the default setting to disallow software
crypto via /dev/crypto now disables accelerated software.
Once a driver is chosen, 'crypto_newsession' is invoked as before.
- Crypto operations are now solely described by the flat 'cryptop'
structure. The linked list of descriptors has been removed.
A separate enum has been added to describe the type of data buffer
in use instead of using CRYPTO_F_* flags to make it easier to add
more types in the future if needed (e.g. wired userspace buffers for
zero-copy). It will also make it easier to re-introduce separate
input and output buffers (in-kernel TLS would benefit from this).
Try to make the flags related to IV handling less insane:
- CRYPTO_F_IV_SEPARATE means that the IV is stored in the 'crp_iv'
member of the operation structure. If this flag is not set, the
IV is stored in the data buffer at the 'crp_iv_start' offset.
- CRYPTO_F_IV_GENERATE means that a random IV should be generated
and stored into the data buffer. This cannot be used with
CRYPTO_F_IV_SEPARATE.
If a consumer wants to deal with explicit vs implicit IVs, etc. it
can always generate the IV however it needs and store partial IVs in
the buffer and the full IV/nonce in crp_iv and set
CRYPTO_F_IV_SEPARATE.
The layout of the buffer is now described via fields in cryptop.
crp_aad_start and crp_aad_length define the boundaries of any AAD.
Previously with GCM and CCM you defined an auth crd with this range,
but for ETA your auth crd had to span both the AAD and plaintext
(and they had to be adjacent).
crp_payload_start and crp_payload_length define the boundaries of
the plaintext/ciphertext. Modes that only do a single operation
(COMPRESS, CIPHER, DIGEST) should only use this region and leave the
AAD region empty.
If a digest is present (or should be generated), it's starting
location is marked by crp_digest_start.
Instead of using the CRD_F_ENCRYPT flag to determine the direction
of the operation, cryptop now includes an 'op' field defining the
operation to perform. For digests I've added a new VERIFY digest
mode which assumes a digest is present in the input and fails the
request with EBADMSG if it doesn't match the internally-computed
digest. GCM and CCM already assumed this, and the new AEAD mode
requires this for decryption. The new ETA mode now also requires
this for decryption, so IPsec and GELI no longer do their own
authentication verification. Simple DIGEST operations can also do
this, though there are no in-tree consumers.
To eventually support some refcounting to close races, the session
cookie is now passed to crypto_getop() and clients should no longer
set crp_sesssion directly.
- Assymteric crypto operation structures should be allocated via
crypto_getkreq() and freed via crypto_freekreq(). This permits the
crypto layer to track open asym requests and close races with a
driver trying to unregister while asym requests are in flight.
- crypto_copyback, crypto_copydata, crypto_apply, and
crypto_contiguous_subsegment now accept the 'crp' object as the
first parameter instead of individual members. This makes it easier
to deal with different buffer types in the future as well as
separate input and output buffers. It's also simpler for driver
writers to use.
- bus_dmamap_load_crp() loads a DMA mapping for a crypto buffer.
This understands the various types of buffers so that drivers that
use DMA do not have to be aware of different buffer types.
- Helper routines now exist to build an auth context for HMAC IPAD
and OPAD. This reduces some duplicated work among drivers.
- Key buffers are now treated as const throughout the framework and in
device drivers. However, session key buffers provided when a session
is created are expected to remain alive for the duration of the
session.
- GCM and CCM sessions now only specify a cipher algorithm and a cipher
key. The redundant auth information is not needed or used.
- For cryptosoft, split up the code a bit such that the 'process'
callback now invokes a function pointer in the session. This
function pointer is set based on the mode (in effect) though it
simplifies a few edge cases that would otherwise be in the switch in
'process'.
It does split up GCM vs CCM which I think is more readable even if there
is some duplication.
- I changed /dev/crypto to support GMAC requests using CRYPTO_AES_NIST_GMAC
as an auth algorithm and updated cryptocheck to work with it.
- Combined cipher and auth sessions via /dev/crypto now always use ETA
mode. The COP_F_CIPHER_FIRST flag is now a no-op that is ignored.
This was actually documented as being true in crypto(4) before, but
the code had not implemented this before I added the CIPHER_FIRST
flag.
- I have not yet updated /dev/crypto to be aware of explicit modes for
sessions. I will probably do that at some point in the future as well
as teach it about IV/nonce and tag lengths for AEAD so we can support
all of the NIST KAT tests for GCM and CCM.
- I've split up the exising crypto.9 manpage into several pages
of which many are written from scratch.
- I have converted all drivers and consumers in the tree and verified
that they compile, but I have not tested all of them. I have tested
the following drivers:
- cryptosoft
- aesni (AES only)
- blake2
- ccr
and the following consumers:
- cryptodev
- IPsec
- ktls_ocf
- GELI (lightly)
I have not tested the following:
- ccp
- aesni with sha
- hifn
- kgssapi_krb5
- ubsec
- padlock
- safe
- armv8_crypto (aarch64)
- glxsb (i386)
- sec (ppc)
- cesa (armv7)
- cryptocteon (mips64)
- nlmsec (mips64)
Discussed with: cem
Relnotes: yes
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D23677
r357614 added CTLFLAG_NEEDGIANT to make it easier to find nodes that are
still not MPSAFE (or already are but aren’t properly marked).
Use it in preparation for a general review of all nodes.
This is non-functional change that adds annotations to SYSCTL_NODE and
SYSCTL_PROC nodes using one of the soon-to-be-required flags.
Mark all obvious cases as MPSAFE. All entries that haven't been marked
as MPSAFE before are by default marked as NEEDGIANT
Approved by: kib (mentor, blanket)
Commented by: kib, gallatin, melifaro
Differential Revision: https://reviews.freebsd.org/D23718
r354748-354750 replaced the KAME macros with m_pulldown() calls.
Contrary to the rest of the network stack m_len checks before m_pulldown()
were not put in placed (see r354748).
Put these m_len checks in place for now (to go along with the style of the
network stack since the initial commits). These are not put in for
performance but to avoid an error scenario (even though it also will help
performance at the moment as it avoid allocating an extra mbuf; not because
of the unconditional function call).
The observed error case went like this:
(1) an mbuf with M_EXT arrives and we call m_pullup() unconditionally on it.
(2) m_pullup() will call m_get() unless the requested length is larger than
MHLEN (in which case it'll m_freem() the perfectly fine mbuf) and migrate the
requested length of data and pkthdr into the new mbuf.
(3) If m_get() succeeds, a further m_pullup() call going over MHLEN will fail.
This was observed with failing auto-configuration as an RA packet of
200 bytes exceeded MHLEN and the m_pullup() called from nd6_ra_input()
dropped the mbuf.
(Re-)adding the m_len checks before m_pullup() calls avoids this problems
with mbufs using external storage for now.
MFC after: 3 weeks
Sponsored by: Netflix
IPPROTO_NONE.
According to RFC4303 2.6 they should be silently dropped.
Submitted by: aurelien.cazuc.external_stormshield.eu
MFC after: 10 days
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D22557
In a few places we have IP6_EXTHDR_GET() left in upper layer protocols.
The IP6_EXTHDR_GET() macro might perform an m_pulldown() in case the data
fragment is not contiguous.
Convert these last remaining instances into m_pullup()s instead.
In CARP, for example, we will a few lines later call m_pullup() anyway,
the IPsec code coming from OpenBSD would otherwise have done the m_pullup()
and are copying the data a bit later anyway, so pulling it in seems no
better or worse.
Note: this leaves very few m_pulldown() cases behind in the tree and we
might want to consider removing them as well to make mbuf management
easier again on a path to variable size mbufs, especially given
m_pulldown() still has an issue not re-checking M_WRITEABLE().
Reviewed by: gallatin
MFC after: 8 weeks
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D22335
When epoch(9) was introduced to network stack, it was basically
dropped in place of existing locking, which was mutexes and
rwlocks. For the sake of performance mutex covered areas were
as small as possible, so became epoch covered areas.
However, epoch doesn't introduce any contention, it just delays
memory reclaim. So, there is no point to minimise epoch covered
areas in sense of performance. Meanwhile entering/exiting epoch
also has non-zero CPU usage, so doing this less often is a win.
Not the least is also code maintainability. In the new paradigm
we can assume that at any stage of processing a packet, we are
inside network epoch. This makes coding both input and output
path way easier.
On output path we already enter epoch quite early - in the
ip_output(), in the ip6_output().
This patch does the same for the input path. All ISR processing,
network related callouts, other ways of packet injection to the
network stack shall be performed in net_epoch. Any leaf function
that walks network configuration now asserts epoch.
Tricky part is configuration code paths - ioctls, sysctls. They
also call into leaf functions, so some need to be changed.
This patch would introduce more epoch recursions (see EPOCH_TRACE)
than we had before. They will be cleaned up separately, as several
of them aren't trivial. Note, that unlike a lock recursion the
epoch recursion is safe and just wastes a bit of resources.
Reviewed by: gallatin, hselasky, cy, adrian, kristof
Differential Revision: https://reviews.freebsd.org/D19111
New sysctl/tunables can now set the interval (in seconds) between
rate-limited crypto warnings. The new sysctls are:
- kern.cryptodev_warn_interval for /dev/crypto
- net.inet.ipsec.crypto_warn_interval for IPsec
- kern.kgssapi_warn_interval for KGSSAPI
Reviewed by: cem
MFC after: 1 month
Relnotes: yes
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D20555
All of these algorithms are either explicitly marked MUST NOT, or they
are implicitly MUST NOTs by virtue of not being included in IETF's
list of protocols at all despite having assignments from IANA.
Specifically, this adds warnings for the following ciphers:
- des-cbc
- blowfish-cbc
- cast128-cbc
- des-deriv
- des-32iv
- camellia-cbc
Warnings for the following authentication algorithms are also added:
- hmac-md5
- keyed-md5
- keyed-sha1
- hmac-ripemd160
Reviewed by: cem, gnn
MFC after: 3 days
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D20340
SADB_ACQUIRE requests are send by kernel, when security policy doesn't
have corresponding security association for outbound packet. IKE daemon
usually registers its handler for such messages and when the kernel asks
for SA it can handle this request. Now such requests will contain
additional fields that can help IKE daemon to create SA. And IKE now
can create SAs using only information from SADB_ACQUIRE request, this
is useful when many if_ipsec(4) interfaces are in use and IKE doesn track
security policies that was installed by kernel.
Obtained from: Yandex LLC
MFC after: 3 weeks
Sponsored by: Yandex LLC
Do not call crypto_newsession() while holding xforms_lock mutex.
Release mutex before invoking crypto_newsession(), and use
ipsec_kmod_enter()/ipsec_kmod_exit() functions to protect from doing
access to unloaded kernel module memory.
Move xform-releated functions into subr_ipsec.c to be able use
ipsec_kmod_* functions. Also unconditionally build ipsec_kmod_*
functions, since now they are always used by IPSec code.
Add xf_cntr field to struct xformsw, it is used by ipsec_kmod_*
functions. Also constify xf_name field, since it is not expected to be
modified.
Approved by: re (kib)
Differential Revision: https://reviews.freebsd.org/D17302
Track session objects in the framework, and pass handles between the
framework (OCF), consumers, and drivers. Avoid redundancy and complexity in
individual drivers by allocating session memory in the framework and
providing it to drivers in ::newsession().
Session handles are no longer integers with information encoded in various
high bits. Use of the CRYPTO_SESID2FOO() macros should be replaced with the
appropriate crypto_ses2foo() function on the opaque session handle.
Convert OCF drivers (in particular, cryptosoft, as well as myriad others) to
the opaque handle interface. Discard existing session tracking as much as
possible (quick pass). There may be additional code ripe for deletion.
Convert OCF consumers (ipsec, geom_eli, krb5, cryptodev) to handle-style
interface. The conversion is largely mechnical.
The change is documented in crypto.9.
Inspired by
https://lists.freebsd.org/pipermail/freebsd-arch/2018-January/018835.html .
No objection from: ae (ipsec portion)
Reported by: jhb
IPSEC_PCBCTL() functions, which include tcp_ipsec_pcbctl(),
ipsec4_pcbctl(), and ipsec6_pcbctl(), should all have matching locking
semantics.
ipsec4_pcbctl() and ipsec6_pcbctl() expect the inp to be unlocked on
entry and exit and appear to be correctly implemented as such. But
tcp_ipsec_pcbctl() had other semantics. This patch fixes the semantics
for tcp_ipsec_pcbctl().
Submitted by: Jason Eggleston <jason@eggnet.com>
MFH: 2 weeks
Sponsored by: Limelight Networks
Differential Revision: https://reviews.freebsd.org/D14623
Per-cpu zone allocations are very rarely done compared to regular zones.
The intent is to avoid pessimizing the latter case with per-cpu specific
code.
In particular contrary to the claim in r334824, M_ZERO is sometimes being
used for such zones. But the zeroing method is completely different and
braching on it in the fast path for regular zones is a waste of time.
Currently it has several disadvantages:
- it uses single mutex to protect internal structures. It is used by
data- and control- path, thus there are no parallelism at all.
- it uses single list to keep encap handlers for both INET and INET6
families.
- struct encaptab keeps unneeded information (src, dst, masks, protosw),
that isn't used by code in the source tree.
- matches are prioritized and when many tunneling interfaces are
registered, encapcheck handler of each interface is invoked for each
packet. The search takes O(n) for n interfaces. All this work is done
with exclusive lock held.
What this patch includes:
- the datapath is converted to be lockless using epoch(9) KPI.
- struct encaptab now linked using CK_LIST.
- all unused fields removed from struct encaptab. Several new fields
addedr: min_length is the minimum packet length, that encapsulation
handler expects to see; exact_match is maximum number of bits, that
can return an encapsulation handler, when it wants to consume a packet.
- IPv6 and IPv4 handlers are stored in separate lists;
- added new "encap_lookup_t" method, that will be used later. It is
targeted to speedup lookup of needed interface, when gif(4)/gre(4) have
many interfaces.
- the need to use protosw structure is eliminated. The only pr_input
method was used from this structure, so I don't see the need to keep
using it.
- encap_input_t method changed to avoid using mbuf tags to store softc
pointer. Now it is passed directly trough encap_input_t method.
encap_getarg() funtions is removed.
- all sockaddr structures and code that uses them removed. We don't have
any code in the tree that uses them. All consumers use encap_attach_func()
method, that relies on invoking of encapcheck() to determine the needed
handler.
- introduced struct encap_config, it contains parameters of encap handler
that is going to be registered by encap_attach() function.
- encap handlers are stored in lists ordered by exact_match value, thus
handlers that need more bits to match will be checked first, and if
encapcheck method returns exact_match value, the search will be stopped.
- all current consumers changed to use new KPI.
Reviewed by: mmacy
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D15617
The RFC specifies that under IPv6 the complete AH header must be 64 bit
aligned, and under IPv4, 32 bit aligned. Prior to this change, we (along
with other BSDs and MacOS) had violated this requirement.
This makes it possible to set up IPv6-AH between Linux and BSD, and also
probably between Windows and BSD.
PR: 222684
Reported and tested by: Jason Mader <jasonmader AT gmail.com>
Obtained from: NetBSD xform_ah.c 1.105
(b939fe2483972eb43d71bf990cfb7f26dece7839 NetBSD/src on GH)
by Maxime Villard
MFC after: 35.2731 hours
Relnotes: probably (breaks ipv6 compat with older FreeBSD/NetBSD/MacOS)
Sponsored by: Dell EMC Isilon
When large SPDs are used, we face two problems:
- too many CPU cycles are spent during the linear searches in the SPD
for each packet
- too much contention on multi socket systems, since we use a single
shared lock.
Main changes:
- added the sysctl tree 'net.key.spdcache' to control the SPD cache
(disabled by default).
- cache the sp indexes that are used to perform SP lookups.
- use a range of dedicated mutexes to protect the cache lines.
Submitted by: Emeric Poupon <emeric.poupon@stormshield.eu>
Reviewed by: ae
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D15050
Don't assume M_PKTHDR is set only on the first mbuf of the chain.
The check is replaced by (m1 != m), which is equivalent to the previous
code: we want to modify m->m_pkthdr.len only when 'm' was not passed in
m_adj().
Fix a pretty bad mistake, that has always been there:
m_adj(m1, -(m1->m_len - roff));
if (m1 != m)
m->m_pkthdr.len -= (m1->m_len - roff);
This is wrong: m_adj() will modify m1->m_len, so we're using a wrong
value when manually adjusting m->m_pkthdr.len.
Reported by: Maxime Villard <max at m00nbsd dot net>
Obtained from: NetBSD
MFC after: 1 week
When using hardware crypto engines, the callback functions used to handle
an IPsec packet after it has been encrypted or decrypted can be invoked
asynchronously from a worker thread that is not associated with a vnet.
Extend 'struct xform_data' to include a vnet pointer and save the current
vnet in this new member when queueing crypto requests in IPsec. In the
IPsec callback routines, use the new member to set the current vnet while
processing the modified packet.
This fixes a panic when using hardware offload such as ccr(4) with IPsec
after VIMAGE was enabled in GENERIC.
Reported by: Sony Arpita Das and Harsh Jain @ Chelsio
Reviewed by: bz
MFC after: 1 week
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D14763
o count in_nomem counter when we have failed to allocate mbuf for
promisc socket;
o count in_msgtarget counter when we have secussfully sent data to socket;
o Since we are sending messages in a loop, returning error on first fail
interrupts the loop, and all remaining sockets will not receive this
message. So, do not return error when we have failed to send data to ALL
or REGISTERED target. Return error only for KEY_SENDUP_ONE case. Now,
when some socket has overfilled its receive buffer, this will not break
other sockets.
MFC after: 2 weeks
Fix a vulnerability in IPsec-IPv6-AH, that allows an attacker to remotely
crash the kernel with a single packet.
In this loop we need to increment 'ad' by two, because the length field
of the option header does not count the size of the option header itself.
If the length is zero, then 'count' is incremented by zero, and there's
an infinite loop. Beyond that, this code was written with the assumption
that since the IPv6 packet already went through the generic IPv6 option
parser, several fields are guaranteed to be valid; but this assumption
does not hold because of the missing '+2', and there's as a result a
triggerable buffer overflow (write zeros after the end of the mbuf,
potentially to the next mbuf in memory since it's a pool).
Add the missing '+2', this place will be reinforced in separate commits.
Reported by: Maxime Villard <maxv at NetBSD.org>
MFC after: 1 week
This reduces noise when kernel is compiled by newer GCC versions,
such as one used by external toolchain ports.
Reviewed by: kib, andrew(sys/arm and sys/arm64), emaste(partial), erj(partial)
Reviewed by: jhb (sys/dev/pci/* sys/kern/vfs_aio.c and sys/kern/kern_synch.c)
Differential Revision: https://reviews.freebsd.org/D10385
SPDB was cleaned using TAILQ_CONCAT() instead of calling key_unlink()
for each SP, thus we need to properly clean lists in each bucket of
V_sphashtbl to avoid panic in hashdestroy() when INVARIANTS is enabled.
Do the same for V_acqaddrhashtbl and V_acqseqhashtbl.
When we are called in DEFAULT_VNET, destroy also all global locks and
drain key_timer callout.
Reported by: kp
Tested by: kp
MFC after: 1 week
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
No functional change intended.
Mainly focus on files that use BSD 3-Clause license.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
Special thanks to Wind River for providing access to "The Duke of
Highlander" tool: an older (2014) run over FreeBSD tree was useful as a
starting point.
The HMAC construction natively permits any key size between 0 and the input
block length. Before r324017, the auth_hash 'keysize' member was the hash
output length, which was used by ipsec for key sizes. (Non-ipsec consumers
need the ability to use other keysizes, hence, r324017.)
The ipsec SADB code blindly uses the auth_hash 'keysize' member for both
minimum and maximum key size, which is wrong (from an HMAC perspective).
For now, just switch it to 'hashsize', which matches the existing
expectations.
Instead it should probably use the range [0, keysize]. But there may be
other broken code in ipsec that rejects hashes with too small a minimum
key size.
Reported by: olivier@
Reviewed by: olivier, no objection from ae
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D12770
key_updateaddresses() is used to update SA addresses and NAT-T
configuration in SADB_UPDATE message. This is done using cloning SA
content from old SA into new one. But addresses and NAT-T configuration
are taking from SADB_UPDATE message. Use newsa pointer to set NAT-T
properties into cloned SA.
PR: 223382
MFC after: 1 week