I was hanging after sending a xfer CTIO and a status CTIO for a non-discon
INQUIRY- the xfer CTIO was returned as completed OK, but the status CTIO
was dropped on the floor. All the fields looked good. I don't know why
it got dropped. But allowing status to go back with data xfer seemed to
work. I also noticed that with a non-disconnecting command that the
firmware handle in the ATIO is zero- this leads me to believe that the
f/w really can only handle one CTIO at a time in the discon case, and
it had no idea what to do with the second (status) CTIO.
CAM_SEND_STATUS. Set a timeout of 2 seconds per CTIO. Make sure
that the 'real' tag value is being checked against- not the
one that also carries the firmware handle.
In our idle loop, use an or instruction to set PRELOADEN rather
than rewriting the contents of DMAPARAMS to DFCNTRL. The later
may re-enable the DMA engine if the idle loop is called to complete
the preload of at least one segment when a target disconnects on
an S/G segment boundary but before we have completed fetching the
next segment. This correts a hang, usually in message out phase,
when this situation occurs. This bug has been here for a long
time, so the situation is rare, but not impossible to reproduce.
It only affected Ultra2/U160 controllers.
Correct a few comments.
Extra Sanity. Make sure that SCSIEN is also turned off, along with
HDMAEN, at the end of the data phase.
aic7xxx.c:
Correct code that traverses the phase table. A much too quick
push to staticize this structure resulted in non-functional
lookup code. This corrects the printing of the phase where
a timeout occurred.
aic7xxx.reg:
Use FIFOQWDEMP as the name for bit 5 of DFSTATUS just like
the Adaptec data books.
aic7xxx.seq:
Refine the 2.1 PCI retry bug workaround for certain, non-ULTRA2,
controllers. When the DMA of an SCB completes, it can take
some time for HDONE to come true after MREQPEN (PCI memory request
pending) falls. If HDONE never comes true, we are in the hung
state and must manually drain the FIFO. We used to test HDONE for
3 clock cycles to detect this condition. This works on all of the
hardware I can personally test. Some controllers were reported
to take 4 clock cycles, so the last version of this code waited
4 clock cycles. This still didn't work for everyone. To fix this,
I've adjusted the work around so that even if the hardware hasn't
hung, but we run the work-around code, the result is a long winded
way to complete the transfer, rather than a hang.
the driver. Doing this breaks the ability to unload the unneeded
parts of the driver (e.g unload the PCI section when using an ISA
card), but currently ifconfig(8) expects an interface `XXX' to have
a driver name of `if_XXX'.
PR: kern/25582
Submitted by: Alexander N. Kabaev <kabaev@mail.ru>, imp (apparently
Warner suggested a similar fix some time ago).
Reviewed by: paul (who would prefer to see ifconfig changed instead)
Add the AAC_DEBUG option to enable debugging in the aac driver.
Correct a race condition in the interrupt handler where the
controller may queue a fib to a response queue after the driver
has serviced the queue but before the interrupt is cleared.
This could leave a completed fib stranded in the response queue
unless another I/O completed and generated another interrupt.
Reviewed by: msmith
- enable 10MHz (fast SCSI) operation on boards that support it. (only
aic6360 boards with fast SCSI enabled can do it)
- bounds check sync periods and offsets passed in from the transport layer
- tell the user which resource allocation failed (for the ISA probe) if we
weren't able to allocate an IRQ, DRQ or I/O port.
supports Xircom netwave series of cards. I have one of these cards
(but am trying to find one or two to test with), but it compiles and
aizu-san says it works.
I don't know if this supports 802.11 or not. I've seen conflicting
information on this.
Submitted by: Hiroyuki Aizu <aizu@jaist.ac.jp>
Obtained from: NetBSD
see atacontrol(8) for more.
Also the ATA_ENABLE_ATAPI_DMA, ATA_ENABLE_WC and ATA_ENABLE_TAGS
options are gone, use the tuneables listed in ata.4 instead from
the loader (this makes it possible to switch off DMA before the
driver has to touch the devices on broken hardware).
a 82557 (e.g.: a newer chip) then:
+ enable MWI, if the PCI configuration indicates the system supports it
+ enable usage of extended TxCB, for better performance
+ enable hardware flow control. FC frames will be passed up to the
host only if promiscuous mode is enabled.
IOMEGA deserves a medal for making the most nonstandard ATAPI
devices, if they are ignorant or just not smart enough I don't
know, but somebody should help them out of their misery...
Proberly fail outstanding bio requests on devices that are detached.
This makes it possible to change between disk/cdrom/dvd/whathaveyou
in a notebook, just by suspending it, changing the device in the
bay (or what you model calls it), unsuspend and the ATA driver
will figure out what disappeared and properly fail those, and attach
any new devices found.
the target mode code or outer layers.
Increase cd_tagval to be 32 bits since it will have to now carry 16
bits of parallel SCSI ATIO handle as well as a normal tag (if any).
Solaris (which, for reasons unknown to me, chokes on u_int16_t
as a typedef of unsigned short if used in a transitional (mixed K&R
and ANSI) way), we'll go the extra mile and fully ANSIfy things.
devices. opening /dev/{dsp,dspW,audio}0 and then opening a different device
from that list and closing it resulted in a panic when any operation is
performed on the first fd.
we prevent this happening by denying the second open unless it uses the same
minor device as the first.
PR: kern/25519
Paste always happens to current _text_ cursor position independently of
mouse cursor position in any case and old variant force user to press
mouse paste button _two_ times if mouse cursor is invisible.
ahc_eisa.c:
Change aic7770_map_int to take an additional irq parameter.
Although we can get the irq from the eisa dev under FreeBSD,
we can't do this under linux, so the OSM interface must supply
this.
ahc_pci.c:
Move ahc_power_state_change() to the OSM. This allows us to
use a platform supplied function that does the same thing.
-current will move to the FreeBSD native API in the near
future.
aic7770.c:
Sync up with core changes to support Linux EISA.
We now store a 2 bit primary channel number rather
than a bit flag that only allows b to be the primary
channel. Adjust for this change.
aic7xxx.c:
Namespace and staticization cleanup. All exported symbols
use an "ahc_" prefix to avoid collisions with other modules.
Correct a logic bug that prevented us from dropping
ATN during some exceptional conditions during message
processing.
Take advantage of a new flag managed by the sequencer
that indicates if an SCB fetch is in progress. If so,
the currently selected SCB needs to be returned to the
free list to prevent an SCB leak. This leak is a rarity
and would only occur if a bus reset or timeout resulting
in a bus reset occurred in the middle of an SCB fetch.
Don't attempt to perform ULTRA transfers on ultra capable
adapters missing the external precision resistor required
for ultra speeds. I've never encountered an adapter
configured this way, but better safe than sorry.
Handle the case of 5MHz user sync rate set as "0" instead of 0x1c
in scratch ram.
If we lookup a period of 0 in our table (async), clear the scsi offset.
aic7xxx.h:
Adjust for the primary channel being represented as
a 2 bit integer in the flags member of the ahc softc.
Cleanup the flags definitions so that comment blocks are
not cramped.
Update seeprom definitions to correctly reflect the fact
that the primary channel is represented as a 2 bit integer.
Add AHC_ULTRA_DIASABLED softc flag to denote controllers
missing the external precision resistor.
aic7xxx.reg:
Add DFCACHETH to the definition of DFSTATUS for completness sake.
Add SEQ_FLAGS2 which currently only contains the SCB_DMA
(SCB DMA in progress) flag.
aic7xxx.seq:
Correct a problem when one lun has a disconnected untagged
transaction and another lun has disconnected tagged transactions.
Just because an entry is found in the untagged table doesn't
mean that it will match. If the match on the lun fails, cleanup
the SCB (return it to the disconnected list or free it), and snoop
for a tag message. Before this change, we reported an unsolicited
reselection. This bug was introduced about a month ago during an
overly aggressive optimization pass on the reselection code.
When cleaning up an SCB, we can't just blindly free the SCB. In
the paging case, if the SCB came off of the disconnected list, its
state may never have been updated in host memory. So, check the
disconnected bit in SCB_CONTROL and return the SCB to the disconnected
list if appropriate.
Manage the SCB_DMA flag of SEQ_FLAGS2.
More carefully shutdown the S/G dma engine in all cases by using
a subroutine. Supposedly not doing this can cause an arbiter hang
on some ULTRA2 chips.
Formatting cleanup.
On some chips, at least the aic7856, the transition from
MREQPEND to HDONE can take a full 4 clock cycles. Test
HDONE one more time to avoid this race. We only want our
FIFO hung recovery code to execute when the engine is
really hung.
aic7xxx_93cx6.c:
Sync perforce ids.
aic7xxx_freebsd.c:
Adjust for the primary channel being a 2 bit integer
rather than a flag for 'B' channel being the primary.
Namespace cleanup.
Unpause the sequencer in one error recovery path that
neglected to do so. This could have caused us to perform
a bus reset when a recovery message might have otherwise been
successful.
aic7xxx_freebsd.h:
Use AHC_PCI_CONFIG for controlling compilation of PCI
support consistently throughout the driver.
Move ahc_power_state_change() to OSM.
aic7xxx_inline.h
Namespace cleanup.
Adjust our interrupt handler so it will work in the edge
interrupt case. We must process all interrupt sources
when the interrupt fires or risk not ever getting an
interrupt again. This involves marking the fact
that we are relying on an edge interrupt in ahc->flags
and checking for this condition in addition to the
AHC_ALL_INTERRUPTS flag. This fixes hangs on the
284X and any other aic7770 installation where level
interrupts are not available.
aic7xxx_pci.c:
Move the powerstate manipulation code into the OSM. Several
OSes now provide this functionality natively.
Take another shot at using the data stored in scratch ram
if the SCB2 signature is correct and no SEEPROM data is
available. In the past this failed if external SCB ram
was configured because the memory port was locked. We
now release the memory port prior to testing the values
in SCB2 and re-acquire it prior to doing termination control.
Adjust for new 2 bit primary channel setting.
Trust the STPWLEVEL setting on v 3.X BIOSes too.
Configure any 785X ID in the same fashion and assume
that any device with a rev id of 1 or higher has the
PCI 2.1 retry bug.
o Separate the kernel stuff from the Yarrow algorithm. Yarrow is now
well contained in one source file and one header.
o Replace the Blowfish-based crypto routines with Rijndael-based ones.
(Rijndael is the new AES algorithm). The huge improvement in
Rijndael's key-agility over Blowfish means that this is an
extremely dramatic improvement in speed, and makes a heck of
a difference in its (lack of) CPU load.
o Clean up the sysctl's. At BDE's prompting, I have gone back to
static sysctls.
o Bug fixes. The streamlining of the crypto stuff enabled me to
find and fix some bugs. DES also found a bug in the reseed routine
which is fixed.
o Change the way reseeds clear "used" entropy. Previously, only the
source(s) that caused a reseed were cleared. Now all sources in the
relevant pool(s) are cleared.
o Code tidy-up. Mostly to make it (nearly) 80-column compliant.
then knocked the extra digits off). Blegh. Update the comment and
adjustment method reading the chip clock year register to note that
anything less than 70 means we're past the year 2000.
in vr_init(). The VIA Rhine chip happens to be able to automatically
read its station address from the EEPROM automatically when reset,
so you don't need to program the filter if you want to keep using the
factory default address, but if you want to change it with "ifconfig vr0
ether xx:xx:xx:xx:xx:xx" then we need to manually set it in the init
routine.
sys/contrib/dev/acpica/Subsystem/Hardware/Attic/hwxface.c to the proper
location after AcpiEnterSleepState().
- Wait for the WAK_STS bit
- Evaluate the _WAK method and check result code
cursor.
The reason is: mouse cursor goes into hide/visible loop while text cursor even
not moved.
PR: 25536
Submitted by: David Xu <davidx@viasoft.com.cn>
palette. As a result, the colors on the video console can look rather
weird. For example, sysinstall on the alpha has a read background. We
can work around this partially by remapping the colors used by syscons for
the ANSI color escape sequences. Note that screen savers and anything that
sets the colors explicitly will still get incorrect colors, but programs
such as sysinstall will now use the correct colors. A more correct fix
would be to actually fix the VGA palette on boot by either swapping all
the red and blue attributes or by hardcoding a standard palette and
overwriting the entire palette.
Requested by: gallatin
Obtained from: NetBSD
bolted to a ne-2000 chip. This is necessary for the NetGear FA-410TX
and other cards.
This also requires you add mii to your kernel if you have an ed driver
configured.
This code will result in a couple of timeout messages for ed on the
impacted cards. Additional work will be needed, but this does work
right now, and many people need these cards.
Submitted by: Ian Dowse <iedowse@maths.tcd.ie>
This is a pretty invasive change, but there are three good
reasons to do this:
1. We'll never have > 16 bits of handle.
2. We can (eventually) enable the RIO (Reduced Interrupt Operation)
bits which return multiple completing 16 bit handles in mailbox
registers.
3. The !)$*)$*~)@$*~)$* Qlogic target mode for parallel SCSI spec
changed such that at_reserved (which was 32 bits) was split into
two pieces- and one of which was a 16 bit handle id that functions
like the at_rxid for Fibre Channel (a tag for the f/w to correlate
CTIOs with a particular command). Since we had to muck with that
and this changed the whole handler architecture, we might as well...
Propagate new at_handle on through int ct_fwhandle. Follow
implications of changing to 16 bit handles.
These above changes at least get Qlogic 1040 cards working in target
mode again. 1080/12160 cards don't work yet.
In isp.c:
Prepare for doing all loop management in outer layers.
newbus in revision 1.19. As a result, lnc was, I believe, broken
for all PCI cards. The softc fields `lnc_btag' and `lnc_bhandle'
were not initialised, `rap', `rdp' and `bdp' were initialised to
the wrong values, and the size of the DMA ring memory was calculated
incorrectly.
Paul Richards has further cleanups in the pipeline, but this at
least is enough to make the driver usable with VMware.
Approved by: paul
for selecting unit). Instead, use the resource hints mechanism.
One unfortunate situation here is that there is no resource_quad_value
function- which is what I needed for WWN boot time replacement. Worse-
you can't store the hint as just plain
hint.isp.0.nodewwn="0x50000000aaaa0001"
because this gets interpreted as an int- incorrectly because it can't
be converted to an int. I can't even get this as a string. To work
around this particular case for nodewwn && portwwn setting, this
rather grotesque form will be used:
hint.isp.0.nodewwn="w50000000aaaa0001"
hint.isp.0.portwwn="w50000000aaaa0002"
At the same time, if we have no hinted WWN, set the default WWN (which, btw,
gets overridden if the card has valid NVRAM, which is usual) to
0x400000007F000009ull (which translates to NAA == IPv4, 127.0.0.9).
Eliminate more printf's and replace them either with device_printf or
isp_prt calls.
ones where we have a CAM path) and replacing them with calls to isp_prt.,
Eliminate isp_unit references- we no longer have an isp_unit- we now
have an isp_dev that device_get_unit can work with.
CVSrepo deletion of the previous attempt will be requested:
--original message--
Add the 'virtual nulmodem driver'
Particularly useful for debuging kernels using vmware.
If your name is Bruce evans and you are a WIZ at tty interfaces,
then you should probably rip this to shreds and offer lots of suggestions and
patches. I've been using this since 4.0-CURRENT and it's never caused
problems but I'm sure I got something wrong. This is similar to the pty/cty
device driver except that both sides are ttys. Even minor numbers
are side A and odd minor numbers are side B.
Work needs to be done regarding what happens to the other side when you
close a node.
to use with vmware, configure vmware to redirect COM2 out to side A of one
of these and boot a kernel with teh gdb remote port set to sio1.
AFTER dropping into the gdb kernel debugger in your test kernel,
fire up gdb with it's remote port pointing at the appropriate side B.
To catch all console output, you can boot the vmware kernel with a serial
console, (COM1) similarly redirected to a nulmodem, and use 'tip' to observe it.
This is practically unaltered since pre 4.0 days except for
changes made along the way needed to make it compile, so any suggestions
or offers of total rewrites will be listenned to :-)
handle read and write requests for widths of multiple bytes. This
can be used to read 16-bit battery status registers for example.
- Remove some unused variables and #if 0'd debugging cruft.
- Don't complain about a GPE query that fails due to AE_NOT_FOUND if the
query method was _Q00.
from a BIF, use the size of the destinatino buffer, not the length of the
string to determine where to put the nul char. As a side effect, the
old code would truncate the string by one character while it was possibly
overflowing the buffer.
o Allocate memory mapped by pcic even when not used for ncv.
This is for PC-Cards which needs offset, because I/O space should not be
used by other devices.
Pointed-out-by: YAMAMOTO Shigeru <shigeru@iij.ad.jp>
If you ever want to run midi(4) out of the giant lock, uncomment
MIDI_OUTOFGIANT in midi.h. Confirmed to work for csamidi with WITNESS
and INVARIANTS.
- midi_info, midi_open and seq_info are now tailqs, allowing arbitrary
numbers of devices to be configured.
- Do not send an active sensing message to reset midi modules.
- Clone /dev/sequencer*. /dev/sequencer0 and /dev/sequencer are generated
upon initialization.
- Convert to a more efficient queueing implementation.
- Don't allocate command buffers on the fly; simply work from a
static pool.
- Add a control device interface, for later use.
- Handle controller overload better as a consequence of the
improved queue implementation.
- Add support for the XPT_GET_TRAN_SETTINGS ccb, and correctly
set the virtual SCSI channels up for multiple outstanding I/Os.
- Update copyrights for 2001.
- Some whitespace fixes to improve readability.
Due to a misunderstanding on my part, previous versions of the
driver were limited to a single outstanding I/O per virtual drive.
Needless to say, this update improves performance substantially.
o Offset and period in synch messages and width negotiation should be
done for per target not per lun. Move these from *lun_info to
*targ_info.
o Change in handling XPT_RESET_DEV and XPT_GET_TRAN_SETTINGS .
o Change CAM_* xpt_done return values.
o Busy loop did not timeout. Change this to timeout as original NetBSD/pc98.
Reviewed by: bsd-nomads ML
attached and ifconfigable. The card doesn't interrupt yet.
Also, move towards bus space by introducing new macros/inline
functions which make such a move much easier than before.
These inline functions are setup now to work around an IBM EtherJet
pccard cardbus bridge incompatibility. The card works in 8 bit mode,
but not in 16-bit mode when it is connected to a cardbus bridge for
reasons unknown. The Linux driver also has a similar workaround in
it.
Future work will include making the above workaround runtime
conditional rather than compile time conditional, as well as fixing
the interrupts in pccards and converting it to bus space.
for the ICB firmware options meant- *I* had taken it to
mean that if you set it, Node Name would be ignored and
derived from Port Name. Actually, it meant the opposite.
As a consequence- change ICBOPT_USE_PORTNAME to the
define ICBOPT_BOTH_WWNS- makes more sense.
Fix wrong input bitmap for MBOX_DUMP_RAM command. Call
ISP_DUMPREGS if we get a f/w crash. Add ISPCTL_RUN_MBOXCMD
control command (so outer layers can run a mailbox command
directly) and add a ISPASYNC_UNHANDLED_RESPONSE hook so
outer layers can understand response queue entries we
might not know about.
- Use pci_get_powerstate()/pci_set_powerstate() in all the other drivers
that need them so we don't have to fiddle with the PCI power management
registers directly.
- Use pci_enable_busmaster()/pci_enable_io() to turn on busmastering and
PIO/memory mapped accesses.
- Add support to the RealTek driver for the D-Link DFE-530TX+ which has
a RealTek 8139 with its own PCI ID. (Submitted by Jason Wright)
- Have the SiS 900/National DP83815 driver be sure to disable PME
mode in sis_reset(). This apparently fixes a problem on some
motherboards where the DP83815 chip fails to receive packets.
(Submitted by Chuck McCrobie <mccrobie@cablespeed.com>)
Use the target offset rather than the target Id to reference
the untagged SCB array. The offset and id are identical save
in the twin channel case. This should correct several issues
with the 2742T.
Set the user and goal settings prior to setting the current
settings. This allows the async update routine to filter out
intermediate transfer negotiation updates that may be less
than interesting. The Linux OSM uses this to reduce the amount
of stuff printed to the console.
aic7xxx.seq:
Correct an issue with the aic7770 in twin channel mode.
We could continually attempt to start a selection even
though a selection was already occurring on one channel.
This might have the side effect of hanging our selection
or causing us to select the wrong device.
While here, create a separate polling loop for when we
have already started a selection. This should reduce
the latency of our response to a (re)selection. The diffs
look larger than they really are due to some code rearrangement
to optimize out a jmp.
aic7xxx_freebsd.c:
Use the target offset rather than the target Id to reference
the untagged SCB array. The offset and id are identical save
in the twin channel case. This should correct several issues
with the 2742T.
aic7xxx_inline.h:
Get back in sync with perforce revision ID.
aic7xxx_pci.c:
Identify adapters in ARO mode as such.
Ensure that not only the subvendor ID is correct (9005)
but also that the controller type field is valid before
looking at other information in the subdevice id. Intel
seems to have decided that their subdevice id of 8086
is more appropriate for some of their MBs with aic7xxx
parts than Adaptec's sanctioned scheme.
Add an exclusion entry for SISL (AAC on MB based adapters).
Adapters in SISL mode are owned by the RAID controller, so
even if a driver for the RAID controller is not present,
it isn't safe for us to touch them.
userland tool:
Use the vfs.devfs.generation sysctl to test for devfs presense
(thanks phk!) when devfs is active it will not try to create the
device nodes in /dev and therefore will not complain about the
failure to do so.
Revert the change in the #define for VINUM_DIR in the kernel
header so that vinum can find its device nodes.
Replace perror() with vinum_perror() to print file/line when
DEVBUG is defined (not defined by default).
kernel:
Don't use the #define names for the "superdev" creation since
they will be prepended by "/dev/" (based on VINUM_DIR), instead
use string constants.
Create both debug and non-debug "superdev" nodes in the devfs.
Problem noticed and fix tested by: Martin Blapp <mblapp@fuchur.lan.attic.ch>
remove_sd_entry() to:
Simplify (hopefully) it by moving all error returns closer to
the beginning of the function.
Return an error when "Error removing subdisk %s: not found in
plex %s\n" would have been reported, as I doubt that we are "OK"
after printing that error message.
Adding make_dev() and destroy_dev() calls in (hopefully) the right
places.
This is done by calling make_dev() in each object constructor and
caching the dev_t's returned from make_dev() in each struct
'subdisk'(sd), 'plex' and 'volume' such that the 'object'_free()
functioncs can call destroy dev.
This change makes a subset of the old /dev/vinum appear under devfs.
Enough nodes appear such that I'm able to mount my striped volume.
There may be more work needed to get vinum configuration working
properly.
case there is nothing to do. This happens normally when the card shares
the interrupt line with other devices.
This code saves a couple of microseconds per interrupt even on a
fast CPU. You normally would not care, except under heavy tinygram
traffic where you can have some 50-100.000 interrupts per second...
On passing, correct a spelling error.
register our sub-busses in the reversed order. In the future, we may provide
a hint to CAM on how to order the scans for multi-function adapters that also
set this flag, but trying to do it the "twin channel" way will lead to
a panic.
- All processes go into the same array of queues, with different
scheduling classes using different portions of the array. This
allows user processes to have their priorities propogated up into
interrupt thread range if need be.
- I chose 64 run queues as an arbitrary number that is greater than
32. We used to have 4 separate arrays of 32 queues each, so this
may not be optimal. The new run queue code was written with this
in mind; changing the number of run queues only requires changing
constants in runq.h and adjusting the priority levels.
- The new run queue code takes the run queue as a parameter. This
is intended to be used to create per-cpu run queues. Implement
wrappers for compatibility with the old interface which pass in
the global run queue structure.
- Group the priority level, user priority, native priority (before
propogation) and the scheduling class into a struct priority.
- Change any hard coded priority levels that I found to use
symbolic constants (TTIPRI and TTOPRI).
- Remove the curpriority global variable and use that of curproc.
This was used to detect when a process' priority had lowered and
it should yield. We now effectively yield on every interrupt.
- Activate propogate_priority(). It should now have the desired
effect without needing to also propogate the scheduling class.
- Temporarily comment out the call to vm_page_zero_idle() in the
idle loop. It interfered with propogate_priority() because
the idle process needed to do a non-blocking acquire of Giant
and then other processes would try to propogate their priority
onto it. The idle process should not do anything except idle.
vm_page_zero_idle() will return in the form of an idle priority
kernel thread which is woken up at apprioriate times by the vm
system.
- Update struct kinfo_proc to the new priority interface. Deliberately
change its size by adjusting the spare fields. It remained the same
size, but the layout has changed, so userland processes that use it
would parse the data incorrectly. The size constraint should really
be changed to an arbitrary version number. Also add a debug.sizeof
sysctl node for struct kinfo_proc.
- Missing cpu_to_scr() added (endian-ness).
Improvement (fix|workaroung??):
- Blindly firing a PPR can lead to some messy situations due to
various causes or misfeatures, for example:
* The 53C1010-[33|66] supports offset 62 in DT mode, but only
offset 31 in ST mode. As a result, a PPR(DT, offset 62)
responded with PPR(ST, any offset > 31) must be rejected.
* A device that doesn't know about PPR should reject it, but
may also be confused by this message.
When a PPR encounters problems, the driver now patches the goal
transfer settings for legacy negotiations to be performed later
with the offending target. This give a chance for bad situations
to be fixed automagically.
Some things needed bits of <i386/include/lock.h> - cy.c now has its
own (only) copy of the COM_(UN)LOCK() macros, and IMASK_(UN)LOCK()
has been moved to <i386/include/apic.h> (AKA <machine/apic.h>).
Reviewed by: jhb
isp_iid_set/isp_iid for fibre channel- this is because we now
fake a port database entry for ourselves. Add the additional loop
states between LOOP_PDB_RCVD and LOOP_READY.
Change and comment on a wad of Fibre Channel isp_control functions.
Change and comment on some of the ISPASYNC Fibre Channel events.
the unit number doesn't get reused.
Make sure that if we've compiled for ISP_TARGET_MODE we set the
default role to be ISP_ROLE_INITIATOR|ISP_ROLE_TARGET.
Do some misc other cleanups.
and depending on role, make sure link is up, scan the fabric (if we're
connected to a fabric), scan the local loop (if appropriate), merge
the results into the local port database then, check once again
to make sure we have f/w at FW_READY state and the the loopstate
is LOOP_READY.
Comment out usage of ISP_SMPLOCK- I have my doubts that this works sanely
as yet because CAM itself still needs Giant. I *was* dropping my lock
and grabbing Giant when doing the upcall for completion, but this is all
seems ridiculous until CAM is fixed.
if we're ISP_ROLE_NONE. Change ISPASYNC_LOGGED_INOUT to ISPASYNC_PROMENADE.
Make sure we note if something is a fabric device.
Target mode:
Finally fix (to a first approximation) SCSI Target Mode again- we needed
to correctly check against CAM_TARGET_WILDCARD and CAM_LUN_WILDCARD
so that targbh won't confuse us. Comment out the drainqueue stuff for
now. Use isp_fc_runstate instead if isp_control/ISPCTL_FCLINK_TEST.
Remove ISP2100_FABRIC defines- we always handle fabric now. Insert
isp_getmap helper function (for getting Loop Position map). Make
sure we (for our own benefit) mark req_state_flags with RQSF_GOT_SENSE
for Fibre Channel if we got sense data- the !*$)!*$)~*$)*$ Qlogic
f/w doesn't do so. Add ISPCTL_SCAN_FABRIC, ISPCTL_SCAN_LOOP, ISPCTL_SEND_LIP,
and ISPCTL_GET_POSMAP isp_control functions. Correctly send async notifications
upstream for changes in the name server, changes in the port database, and
f/w crashes. Correctly set topology when we get a ASYNC_PTPMODE event.
Major stuff:
Quite massively redo how we handle Loop events- we've now added several
intermediate states between LOOP_PDB_RCVD and LOOP_READY. This allows us
a lot finer control about how we scan fabric, whether we go further
than scanning fabric, how we look at the local loop, and whether we
merge entries at the level or not. This is the next to last step for
moving managing loop state out of the core module entirely (whereupon
loop && fabric events will simply freeze the command queue and a thread
will run to figure out what's changed and *it* will re-enable the queu).
This fine amount of control also gets us closer to having an external
policy engine decide which fabric devices we really want to log into.
Style nits.
Make sure that our selection hardware is disabled
as soon as possible after detecting a busfree and
even go so far as to disable the selection hardware
in advance of an event that will cause a busfree
(ABORT or BUS DEVICE RESET message). The concern
is that the selection hardware will select a target
for which, after processing the bus free, there
will be no commands pending. The sequencer idle
loop will re-enable the selection should it still be
necessary.
In ahc_handle_scsiint(), clear SSTAT0 events several
PCI transactions (most notably reads) prior to clearing
SCSIINT. The newer chips seem to take a bit of time to
see the change which can make the clearing of SCSIINT
ineffective.
Don't bother panicing at the end of ahc_handle_scsiint().
Getting to the final else just means we lost the race
with clearing SCSIINT.
In ahc_free(), handle init-level 0. This can happen when we
fail the attach for RAID devices. While I'm here, also kill
the parent dma tag.
In ahc_match_scb(), consider initiator ccbs to be any
that are not from the target mode group. This fixes
a bug where an external target reset CCB was not getting
cleaned up by the reset code.
Don't bother freezing a ccb in any of our "abort" routines
when the status is set to CAM_REQ_CMP. This can happen
for a target reset ccb.
aic7xxx.reg:
Reserve space for a completion queue. This will be used
to enhance performance in the near future.
aic7xxx.seq:
Remove an optimization for the 7890 autoflush bug that
turned out to allow, in rare cases, some data to get
lost.
Implement a simpler, faster, fix for the PCI_2_1 retry
bug that hangs the sequencer on an SCB dma for certain chips.
Test against SAVED_SCSIID rather than SELID during target
reselections. This is how we always did it in the past,
but the code was modified while trying to work around an
issue with the 7895. SAVED_SCSIID takes into account
twin channel adapters such as the 2742T, whereas SELID
does not have the channel bit. This caused invalid
selection warnings and other strangeness on these cards.
aic7xxx_pci.c
Use the correct mask for checking the generic aic7892
entry.
- Use swi_* function names.
- Use void * to hold cookies to handlers instead of struct intrhand *.
- In sio.c, use 'driver_name' instead of "sio" as the name of the driver
lock to minimize diffs with cy(4).
This mistake seems to have been benign until very recently, probably
until msmith's PCI code reshuffle which cleaned up a lot of things.
Still, my AIC7770 doesn't work again, but it at least probes the
EISA bus now.
mtx_enter(lock, type) becomes:
mtx_lock(lock) for sleep locks (MTX_DEF-initialized locks)
mtx_lock_spin(lock) for spin locks (MTX_SPIN-initialized)
similarily, for releasing a lock, we now have:
mtx_unlock(lock) for MTX_DEF and mtx_unlock_spin(lock) for MTX_SPIN.
We change the caller interface for the two different types of locks
because the semantics are entirely different for each case, and this
makes it explicitly clear and, at the same time, it rids us of the
extra `type' argument.
The enter->lock and exit->unlock change has been made with the idea
that we're "locking data" and not "entering locked code" in mind.
Further, remove all additional "flags" previously passed to the
lock acquire/release routines with the exception of two:
MTX_QUIET and MTX_NOSWITCH
The functionality of these flags is preserved and they can be passed
to the lock/unlock routines by calling the corresponding wrappers:
mtx_{lock, unlock}_flags(lock, flag(s)) and
mtx_{lock, unlock}_spin_flags(lock, flag(s)) for MTX_DEF and MTX_SPIN
locks, respectively.
Re-inline some lock acq/rel code; in the sleep lock case, we only
inline the _obtain_lock()s in order to ensure that the inlined code
fits into a cache line. In the spin lock case, we inline recursion and
actually only perform a function call if we need to spin. This change
has been made with the idea that we generally tend to avoid spin locks
and that also the spin locks that we do have and are heavily used
(i.e. sched_lock) do recurse, and therefore in an effort to reduce
function call overhead for some architectures (such as alpha), we
inline recursion for this case.
Create a new malloc type for the witness code and retire from using
the M_DEV type. The new type is called M_WITNESS and is only declared
if WITNESS is enabled.
Begin cleaning up some machdep/mutex.h code - specifically updated the
"optimized" inlined code in alpha/mutex.h and wrote MTX_LOCK_SPIN
and MTX_UNLOCK_SPIN asm macros for the i386/mutex.h as we presently
need those.
Finally, caught up to the interface changes in all sys code.
Contributors: jake, jhb, jasone (in no particular order)
* a ">" is really ">=" ;
* do not try to fetch zero-sized blocks from the card;
* make sure that bpf gets the packets it wants even with
bridging active;
adv_free() as the ISA probe routine doesn't malloc() ccb_infos but does
call adv_free().
- Release the ISA-only overrun DMA tags, bufs, and maps if the probe fails.
Tested by: rwatson
except for setting it. Also remove count from aha and replace it with
optional.
Also add commented out pccard lines for all the old card drivers.
They have to be commented out until they are converted because it
causes problems in NEWCARD.
striped plexes. This prevents various panics introduced in the last
rewrite of the locking code.
Suffered by: "Niels Chr. Bank-Pedersen" <ncbp@bank-pedersen.dk>
Turn off semaphores. Nobody else implements them, and there is lots of
AML out there which does totally absurd things with them, meaning that
if we try to do the right thing we are guaranteed to fail.
Use acpi_EvaluateInteger where possible.
Use FuncName rather than &FuncName when passing function addresses.
Don't evaluate the _REG method when we attach to an address space -
AcpiInstallAddressSpaceHandler does it for us.
acpi_EvaluateInteger.
Use acpi_EvaluateInteger instead of doing things the hard way where
possible.
AcpiSetSystemSleepState (unofficial) becomes AcpiEnterSleepState.
Use the AcpiGbl_FADT pointer rather than searching for the FADT.
incompletely converting simplelocks to mutexes (COM_LOCK() is supposed
to hide the SMP locking internals, but it now depends on mutex interfaces
being visible).
- When used on a 33MHz PCI BUS, the 53C1010-66 revision 0
requires extra clocks to be inserted in data out phase.
Revision 1 is fixed.
- The 53C1010-33 revision 1 requires internal cycles to be
disabled due to possible contentions on IO registers.
Revision 2 is fixed.
Fix:
- The probing of HVD from GPIO3 bit by the driver was reversed.
The driver could misprobe the bus mode of a 825 or 875 chip
that was not previously initialized (no BIOS for example).
is going away soon anyways. Instead, don't pass MTX_RECURSE to mtx_init,
so that WITNESS will panic if the driver mutex is recursed on.
- Use MTX_DEF in mtx_init() instead of assuming that it will be 0.
even if mode PS/2 is forced with bootflags. As a matter of fact,
chipsets needs some extra configuration for accessing PS/2 mode
from ECP. The current patch is only relevant for generic chipsets
since specific code is supposed to deal with this during detection.
an override as a loader settable variable (fxp_iomap). fxp_iomap is
a bitmap of fxp units that should be configured to use PCI I/O space
in stead of PCI Memory space.
Reviewed by: Kees Jan Koster <dutchman@tccn.cs.kun.nl>, dg@freebsd.org
