demand-dial links with dynamic IP numbers where the program
that causes the dial bind()s to an interface address that is
subsequently changed after ppp negotiation.
The problem is defeated by adding negotiated addresses to the
tun interface as additional alias addresses and providing a set
of ``iface'' commands for managing the interface. Libalias is
also required (and what a name clash!) - it happily IP-aliases
the address so that the source is that of the primary (negotiated)
interface and un-IP-aliases it on the way back.
An ``enable iface-alias'' is done implicitly by the -alias command
line switch. If -alias isn't given, iface-aliasing is disabled by
default and can't be enabled 'till an ``alias enable yes'' is done.
``alias enable no'' silently disables iface-alias.
So, for dynamic-IP-type-connections, running ``ppp -alias -auto blah''
will work for the first connection, although existing bindings will
not survive a disconnect/connect as the TCP peer will be trying to
send to the old IP address - the packets won't route.
It's now a lot easier to add IPXCP to ppp with minor updates to
the new iface.[ch] (if anyone ever gets 'round to it).
It's also now possible to manually add interface aliases with
something like ``iface add 1.2.3.4/24 5.6.7.8''. This allows
multi-homed ppp links :-)
is not possible to switch to or from dedicated or direct mode,
but all other combinations are ok (eg. -auto -> -ddial).
o Cope with the fact that commands with optional context may not
be able to obtain a link with command_ChooseLink() (if all links
have been deleted for example).
o Allow `clone'ing in non-multilink mode. We may for example want
to configure two links in unilink mode and dial them both, using
the one that comes up first. It's also possible to rename
``deflink'' by cloning it, deleting the original, then setting
the mode of the new link.
Any `add' or `delete' command that uses MYADDR or HISADDR
will be added to the sticky route list (show ipcp). When
MYADDR or HISADDR change due to IPCP negotiations, and if
`sroutes' is enabled (the default), all sticky route
entries are updated in the routing table.
The end result is that `add default hisaddr' will ``stick'',
as will ``add myaddr 255.255.255.255 127.0.0.1'' and
``add 1.2.3.4 255.255.255.0 hisaddr''.
call it after link authentication.
o Pretty print our bundle MTU.
o Correct MP header encoding and decoding (should be network byte order).
o Add some debug diagnostics so that we can see MP fragment sending and
re-assembly.
and denied by default (POLA).
o Remove ``enable'' msext. Now, doing a ``set nbns'' will
automatically enable a NBNS ACK/NAK rather than a REJ.
o Add accept|disable|deny|enable dns. If we ``accept'',
we'll tell the peer what our nameservers are (if he asks).
The values in resolv.conf can be overridden with the
``set dns'' command. If we ``enable'', we'll REQ using
our resolv.conf entries, and any NAKs are written back to
resolv.conf.
o Remove ``show msext'' and show the relevent IP numbers in
``show ipcp''.
bundle (non-negotiated vars) or to their respective IPCP,
LCP or CCP.
o Enable rolling throughput statistics by default.
o Remove the `display' command. These values now appear in
`show bundle', `show ipcp', `show ccp' and `show lcp'.
o Initialise auth name & key at bundle create time (oops).
o Rename pppd-deflate (the id-24 hack) to deflate24.
o Don't send both a REJ and a NAK to an IPCP or LCP REQ.
Favour the REJ (already done at the CCP level).
o Recurse in datalink_UpdateSet() when we change state, otherwise
we end up setting no descriptors and getting jammed in the
imminent select() instead of doing the dial/login/hangup.
o Display our CHAP encryption method despite being built with DES.
o Display VJ as not negotiated in ``show ipcp'' when necessary.
o Shuffle things that live at the datalink level into
``show link'' rather than ``show modem''.
o Make both ``show'' commands prettier and more consistent,
and display carrier status, link type and our name in
``show modem''.
o Show redial and reconnect information in ``show link''
and remove ``show redial'' and ``show reconnect''.
o Down the correct link in bundle_LinkLost().
o Remove stale -direct and -background links at the end
of our main loop, not when we know they're going. This
prevents unexpected pointer-invalidations...
o If we ``set server'' with the same values twice, notice
and don't moan about failure.
o Record dial script despite our link mode. The mode may
be changed later (next mod) :-) We never run scripts
in -direct and -dedicated modes.
o Make ``set server none'' functional again.
o Correct datalink state array so that we don't report an
``unknown'' state.
o Pass struct ipcp to IpcpCleanInterface, not struct fsm.
o Create TUN_PREFIX define rather than hard-coding in main.c
o prompt_TtyInit now handles a NULL prompt for -direct mode
rather than having to create one then destroy it uncleanly.
o Mention our mode in the "PPP Started" LogPHASE message.
o Bring all auto links up when we have something to send.
o Remove some redundant Physical_*() functions.
o Show which connection is running a command when logging
commands.
o Initialise throughput uptime correctly.
o Move Var*Version into command.c
o Remove struct pppVars (and there was much rejoicing) !
o Forward-decl some structs in .h files to avoid include
ordering requirements and remove a few more redundant
#includes.
struct lcp and display them in `show lcp'.
o Remove `show mru' and `show mtu' and make the data part of
`show lcp'. Also merge `set m[tr]u' and `set openmode'
implementations into the SetVariable function.
o `set timeout' only accepts the idle timer value as an argument.
o Move our lqr period into struct lcp, and create a `set lqrperiod'
command. Display it in `show lcp'.
o Remove VarRetryTimeout, and implement it at the LCP, PAP, CHAP,
CCP and IPCP levels, creating individual `set XXXretry' commands
for each. They must be separate because they have different
context requirements in multilink mode.
o Display default config values in `show ccp'.
o Tart the man page up a bit (wrt PPP/TCP, compression and LQR) and
explain the new commands.
o Don't remove routes and DOWN the interface when we're
closed in auto mode.
o Initialize the FSMs in bundle_Create.
o Initialize ipcp::if_mine & ipcp::if_peer only once (so
that we don't forget that we've SIOCAIFADDR'd the interface).
o Do a SIOCDIFADDR on the specific address to avoid hurting any
other (still non-existent) NCPs.
o Fix some error/diagnostic messages.
o The FSM layering is now more sane.
o Move a lot of the NCP stuff into our ipcpstate rather than having it
in the bundle, including control of the configured IP addresses. We
don't need hacks like the global `linkup' variable any more as the
FSM decides when our ppp.link* files get run. This is going to eventually
be configurable based on FSM events anyway.
o Fix a few inconsistencies when both sides require authentication.
o We now have "Ppp..." and "PPp" prompts, reflecting authentication
and network phase. We don't print loads of spurious prompts as we
change phases any more.
o Our phase is part of the bundle now.
o Fix a bug where the FSM wasn't calling LayerFinish.
o Close the FSM down correctly with a signal rather than slamming it
down as if the line was dropped (the undocumented ``down'' command
is still available though).
o Remove the forgotten `tunno' variable and fix references to it.
This structure will eventually contain a list of NCPs (currently
only IPCP is supported) and a list of physical `struct link's.
It will also derive from a struct link itself.
Make ModemTimeout() static - it's way to dangerous to be called
from outside !
Bump version to 1.9. Our first MP release should be 2.0.
IPCP, CCP and LCP are now just derived FSMs.
Comment each of the FSM implementations so that we can
tell what's going on.
Revise the state transitions so that CCP and IPCP actually
send terminate REQs when appropriate.
The OS & IPCP layers are still like spagetti (next job).
o Use INADDR_ANY and INADDR_BROADCAST instead of 0 and 0xffffffff
for IP addresses & masks.
o Move struct compreq into ipcp.c (it's none of anyone elses
business).
o Rename MAX_STATES to MAX_VJ_STATES.
o Allow a forth argument in ppp.secret, specifying a new
label. This gives control over which section of
ppp.link{up,down} is used based on the authenticated user.
o Support random address ranges in ppp.secret (not just in ppp.conf).
o Add a AUTHENTICATING INCOMING CONNECTIONS section to the man page.
o Add a bit more about DEFLATE in the man page.
o Fix the incorrect "you must specify a password in interactive
mode" bit of the manual.
o Space things in the man page consistently.
o Be more precice about where you can use MYADDR, HISADDR and INTERFACE
in the "add" command documentation.
Validate the peers suggested IP by attempting to make a routing table
entry.
Give up IPCP negotiation if the peer NAKs us with an unusable IP.
Always SIOCDIFADDR then SIOCAIFADDR when configuring the tun device.
Using SIOCSIFDSTADDR allows duplicate dst addresses (which we don't
want)!!!
Allow up to 200 interface names (was 50) (now that ppp can play server
properly).
Up the version number (1.5 -> 1.6).
Cosmetic:
Log unexpected CCP packets in the CCP log rather than the ERROR log.
Log unexpected Config Reqs in the appropriate LCP/IPCP/CCP log rather
than the ERROR log.
Log failed route additions and deletions with WARN, not TCPIP.
Log the option id and length for unrecognised IPCP options.
Change some .Sq to .Ar in the man page.
Remove extraneous decls.
Add ``const'' to several places.
Allow ``make NOALIAS=1'' to remove IP aliasing.
Merge with OpenBSD - only the Makefiles vary.
We can now survive a compile with
-Wall -Wbad-function-cast -Wcast-align -Wcast-qual
-Winline -Wmissing-declarations -Wmissing-prototypes
-Wnested-externs -Wpointer-arith -Wredundant-decls
-Wshadow -Wstrict-prototypes -Wwrite-strings -Wchar-subscripts
(although the Makefile just contains -Wall).
o Add missing $Id$s
o Move extern decls from .c -> .h files
o Staticize
o Remove #includes from .h files
o style(9)ify includes
o bcopy -> memcpy
bzero -> memset
bcmp -> memcmp
index -> strchr
rindex -> strrchr
o Move timeout.h -> timer.h (making it consistent w/ timer.c)
o Add -Wmissing-prototypes
o Use syslog
o Remove references to stdout/stderr (incl perror())
o Introduce VarTerm - the interactive terminal or zero
o Allow "set timeout" to affect current session
o Change "set debug" to "set log"
o Allow "set log [+|-]flag"
o Make MSEXT and PASSWDAUTH stuff the default
o Move all #ifdef DEBUG stuff into the code - this
shouldn't be too much overhead. It's now controlled
with "set log +debug"
o Add "set log command, debug, tun, warn, error, alert"
o Remove cdefs.h, and assume an ansi compiler.
o Improve all diagnostic output
o Don't trap SIGSEGV
o SIGHUP now terminates again (log files are controlled
by syslog)
o Call CloseModem() when changing devices
o Fix parsing of third arg of "delete"
I think this fixes the "magic is same" problems that some
people have been experiencing.
The man page is being rewritten. It'll follow soon.
This will make a number of things easier in the future, as well as (finally!)
avoiding the Id-smashing problem which has plagued developers for so long.
Boy, I'm glad we're not using sup anymore. This update would have been
insane otherwise.
on their own without even attempting to get concensus in the IETF, but
there are also lots of Win95/NT boxes out there.
CLoses PR#1494
Submitted-By: Peter Childs <pjchilds@imforei.apana.org.au>
o Supporting SYNC SIO device (But need a device driver)
- add "set speed sync"
o Fixing bug for Predictor-1 function.
o Add new parameter that re-sent interval for set timeout commands.
o Improving RTT (Round Trip Time) and reducing processor time.
- Previous Timer service was using polling, and now using
SIGALRM ;-)
- A 0.94beta2 will not work correctly....
-- Follows are additinal feature not including 0.94beta2
o Support Proxy ARP
- add "enable/disable proxy" commands
o Marging common routine in CHAP/PAP.
o Enhancing LCP/IPCP log information.
o Support local Authfication connection on port 300x and tty.
- You can set up pair of your "hostname -s" and
password in ppp.secret. if either ppp.secret file nor
your hostname line don't exist, It will notify a message
and working as same as previous version.(Backword compatibility)
- If you did set up them, It's allow connection but nothing to do
except help and passwd command.
- add "passwd yourpasswd" commands
o Support afilter - keep Alive filter that a packet can send/receiving
according to ifilter/ofilter but doesn't count it as preventing idle
timer expires.
- Same syntax of other filters.
o Fixing bugs reported by current user for previous one. Thanks !!
Reviewed by: Atsushi Murai (amurai@spec.co.jp)
