Don't mention the authors name at startup. He's already credited
in the man page. Instead, make the message consistent with the
one given to the diagnostic port (and fix the grammar when entering
`term' mode).
Don't credit the zlib author in the man page as ppp isn't linked
directly with zlib (it's shared).
Mention when the OpenBSD port was first made available.
The delay defaults to 1 sec (as it always has) unless we've done
a ~p in interactive mode or we've actually detected a HDLC frame.
This is now cleanly implemented (via async timers) so that it is
possible for LCP to come up despite the delay if an LCP REQ is
received.
This will hopefully solve situations with slow servers or slirp
scenarios (where ECHO is left on the port for a second or so before
the peer enters packet mode).
Also, ~p in interactive mode no longer changes the value of the default
openmode delay and -dedicated mode enters packet mode in the right state
according to the value of openmode.
o Allow a forth argument in ppp.secret, specifying a new
label. This gives control over which section of
ppp.link{up,down} is used based on the authenticated user.
o Support random address ranges in ppp.secret (not just in ppp.conf).
o Add a AUTHENTICATING INCOMING CONNECTIONS section to the man page.
o Add a bit more about DEFLATE in the man page.
o Fix the incorrect "you must specify a password in interactive
mode" bit of the manual.
o Space things in the man page consistently.
o Be more precice about where you can use MYADDR, HISADDR and INTERFACE
in the "add" command documentation.
not in -auto mode isn't a good idea, and that the
add should be done in ppp.linkup instead.
Change "add 0 0 HISADDR" to "add default HISADDR". It's
more intuitive.
RTM_CHANGE if the RTM_ADD fails with an EEXIST.
Allow "delete! dst" (note the ``!'') to silently
fail if the RTM_DELETE fails with an ESRCH.
Also, make the ESRCH and EEXIST error conditions
more understandable to the casual observer.
when command logging is switched on.
o Display ******** for the authkey for "show auth"
o Document how \P should be used, and document the other chat escapes
while I'm there.
o Make sure the full command is displayed when a compound command
fails - ie, "set novar rubbish" should say "set novar: Invalid command"
rather than "novar: Invalid command"
Problem pointed out by: Theo de Raadt <deraadt@cvs.openbsd.org> (among others)
Validate the peers suggested IP by attempting to make a routing table
entry.
Give up IPCP negotiation if the peer NAKs us with an unusable IP.
Always SIOCDIFADDR then SIOCAIFADDR when configuring the tun device.
Using SIOCSIFDSTADDR allows duplicate dst addresses (which we don't
want)!!!
Allow up to 200 interface names (was 50) (now that ppp can play server
properly).
Up the version number (1.5 -> 1.6).
Cosmetic:
Log unexpected CCP packets in the CCP log rather than the ERROR log.
Log unexpected Config Reqs in the appropriate LCP/IPCP/CCP log rather
than the ERROR log.
Log failed route additions and deletions with WARN, not TCPIP.
Log the option id and length for unrecognised IPCP options.
Change some .Sq to .Ar in the man page.
Delete AF_LINK routes as well as AF_INET.
Allow the word `default' as the arg to `delete' or in place of the
first two args (dest & netmask) to `add'.
Accept INTERFACE as the third arg to `add'.
You can now say `add default interface' to create a default route
through the tun interface. It's reported that subsequent bind()s
will bind to a broadcast address and not to the address currently
assigned to the tun device - this is the first step towards
supporting that first connection that was around from before the
dynamic IP negotiation....
(I *really* meant to do this *before* committing the
deflate changes in the first place - oops).
Pppd is horribly broken in this respect - refer to the
ppp man page for details. Ppp *WON'T* negotiate deflate
with pppd by default - you must ``enable'' and ``accept''
``pppd-deflate'' in your config.
While I'm in there, update the cftypes in ccp.c so that
we recognise some more protocols (we don't actually do
anything with them - just send a REJ).
o Add "allow" command:
"allow users a b c" gives access to users a, b and c.
"allow modes auto" gives those users access to auto mode only.
"allow users *" and "allow modes *" are accepted.
No users and all modes are allowed by default.
UID 0 can do anything.
o Set the current label with the "load" and "dial" commands
so that the call to ppp.linkdown makes sense.
o Up the verison number.
o Don't OR MODE_AUTO for -background and -ddial.
o Don't OR MODE_INTER when we get a diagnostic connection.
o Allow up to 40 args per line (was 20).
o "set ifaddr" only changes the interface in AUTO mode (with other
modes, it happens after IPCP negotiation).
o Sort command descriptions in the man page.
o Support -dedicated mode where we just talk ppp forever (no login etc).
Stay as the invoking uid as much as possible.
Execution as a normal user is still forbidden for now,
so these changes are pretty ineffective.
The next commit will implement the modifications suggested
on -hackers a number of days ago.
Insist that uid == 0 for client ppp
Disallow client sockets if no password is specified
Don't exit on failure to open client socket for listening
Allow specification of null local password
Use reasonable size (smaller) ``vector''s in auth.c
Fix "passwd ..." usage message
Insist on "all" as arg to "quit" (if any)
Drop client socket connection before Cleanup() when "quit all"
This tells ppp to loopback packets addressed to
the ppp interface IP coming *from* the tun
device.
This means that you can ping the tun interface IP
from inside :-)
idependently time out any of the FSMs.
Split LCP logging into LCP, IPCP and CCP logging,
and make room in "struct fsm" for the log level
that the state machine should use.
"set stopped" directive. If the timeout occurs
it will cause a "Down" event, hanging up the line
if it's still up. This *isn't* part of the FSM
diagram, but I consider it ok as a "higher level
implementation specific timeout" as specified in
the rfc ;-}
Discussed briefly with: joerg
