CPU for too long period than necessary. Additively, interfaces are kept
polled (in the tick) even if no more packets are available.
In order to avoid such situations a new generic mechanism can be
implemented in proactive way, keeping track of the time spent on any
packet and fragmenting the time for any tick, stopping the processing
as soon as possible.
In order to implement such mechanism, the polling handler needs to
change, returning the number of packets processed.
While the intended logic is not part of this patch, the polling KPI is
broken by this commit, adding an int return value and the new flag
IFCAP_POLLING_NOCOUNT (which will signal that the return value is
meaningless for the installed handler and checking should be skipped).
Bump __FreeBSD_version in order to signal such situation.
Reviewed by: emaste
Sponsored by: Sandvine Incorporated
vr(4) overhauling(r177050).
It seems that filtering multicast addresses with multicast CAM
entries require accessing 'CAM enable bit' for each CAM entry.
Subsequent accessing multicast CAM control register without
toggling the 'CAM enable bit' seem to no effects.
In order to fix that separate CAM setup from CAM mask configuration
and CAM entry modification. While I'm here add VLAN CAM filtering
feature which will be enabled in future(FreeBSD now can receive
VLAN id insertion/removal event from vlan(4) on the fly).
For VT6105M hardware, explicitly disable VLAN hardware tag
insertion/stripping and enable VLAN CAM filtering for VLAN id 0.
This shall make non-VLAN frames set VR_RXSTAT_VIDHIT bit in Rx
status word.
Added multicast/VLAN CAM address definition to header file.
PR: kern/125010, kern/125024
MFC after: 1 week
years. All datasheet I have indicates the bit 15 is the
VR_RXSTAT_RX_OK. The bit 14 is reserved for all Rhine family
except VT6105M. VT6105M uses that bit to indicate a VLAN frame
with matching CAM VLAN id.
Use the VR_RXSTAT_RX_OK instead of VR_RXSTAT_RXERR when vr(4)
checks the validity of received frame.
This should fix occasional dropping frames on VT6105M.
Tested by: Goran Lowkrantz ( goran.lowkrantz at ismobile dot com )
MFC after: 1 week
state change and reliable error recovery.
o Moved vr_softc structure and relevant macros to header file.
o Use PCIR_BAR macro to get BARs.
o Implemented suspend/resume methods.
o Implemented automatic Tx threshold configuration which will be
activated when it suffers from Tx underrun. Also Tx underrun
will try to restart only Tx path and resort to previous
full-reset(both Rx/Tx) operation if restarting Tx path have failed.
o Removed old bit-banging MII interface. Rhine provides simple and
efficient MII interface. While I'm here show PHY address and PHY
register number when its read/write operation was failed.
o Define VR_MII_TIMEOUT constant and use it in MII access routines.
o Always honor link up/down state reported by mii layers. The link
state information is used in vr_start() to determine whether we
got a valid link.
o Removed vr_setcfg() which is now handled in vr_link_task(), link
state taskqueue handler. When mii layer reports link state changes
the taskqueue handler reprograms MAC to reflect negotiated duplex
settings. Flow-control changes are not handled yet and it should
be revisited when mii layer knows the notion of flow-control.
o Added a new sysctl interface to get statistics of an instance of
the driver.(sysctl dev.vr.0.stats=1)
o Chip name was renamed to reflect the official name of the chips
described in VIA Rhine I/II/III datasheet.
REV_ID_3065_A -> REV_ID_VT6102_A
REV_ID_3065_B -> REV_ID_VT6102_B
REV_ID_3065_C -> REV_ID_VT6102_C
REV_ID_3106_J -> REV_ID_VT6105_A0
REV_ID_3106_S -> REV_ID_VT6105M_A0
The following chip revisions were added.
#define REV_ID_VT6105_B0 0x83
#define REV_ID_VT6105_LOM 0x8A
#define REV_ID_VT6107_A0 0x8C
#define REV_ID_VT6107_A1 0x8D
#define REV_ID_VT6105M_B1 0x94
o Always show chip revision number in device attach. This shall help
identifying revision specific issues.
o Check whether EEPROM reloading is complete by inspecting the state
of VR_EECSR_LOAD bit. This bit is self-cleared after the EEPROM
reloading. Previously vr(4) blindly spins for 200us which may/may
not enough to complete the EEPROM reload.
o Removed if_mtu setup. It's done in ether_ifattach().
o Use our own callout to drive watchdog timer.
o In vr_attach disable further interrupts after reset. For VT6102 or
newer hardwares, diable MII state change interrupt as well because
mii state handling is done by mii layer.
o Add more sane register initialization for VT6102 or newer chips.
- Have NIC report error instead of retrying forever.
- Let hardware detect MII coding error.
- Enable MODE10T mode.
- Enable memory-read-multiple for VT6107.
o PHY address for VT6105 or newer chips is located at fixed address 1.
For older chips the PHY address is stored in VR_PHYADDR register.
Armed with these information, there is no need to re-read
VR_PHYADDR register in miibus handler to get PHY address. This
saves one register access cycle for each MII access.
o Don't reprogram VR_PHYADDR register whenever access to a register
located at a PHY address is made. Rhine fmaily allows reprogramming
PHY address location via VR_PHYADDR register depending on
VR_MIISTAT_PHYOPT bit of VR_MIISTAT register. This used to lead
numerous phantom PHYs attached to miibus during phy probe phase and
driver used to limit allowable PHY address in mii register accessors
for certain chip revisions. This removes one more register access
cycle for each MII access.
o Correctly set VLAN header length.
o bus_dma(9) conversion.
- Limit DMA access to be in range of 32bit address space. Hardware
doesn't support DAC.
- Apply descriptor ring alignment requirements(16 bytes alignment)
- Apply Rx buffer address alignment requirements(4 bytes alignment)
- Apply Tx buffer address alignment requirements(4 bytes alignment)
for Rhine I chip. Rhine II or III has no Tx buffer address
alignment restrictions, though.
- Reduce number of allowable number of DMA segments to 8.
- Removed the atomic(9) used in descriptor ownership managements
as it's job of bus_dmamap_sync(9).
With these change vr(4) should work on all platforms.
o Rhine uses two separated 8bits command registers to control Tx/Rx
MAC. So don't access it as a single 16bit register.
o For non-strict alignment architectures vr(4) no longer require
time-consuming copy operation for received frames to align IP
header. This greatly improves Rx performance on i386/amd64
platforms. However the alignment is still necessary for
strict-alignment platforms(e.g. sparc64). The alignment is handled
in new fuction vr_fixup_rx().
o vr_rxeof() now rejects multiple-segmented(fragmented) frames as
vr(4) is not ready to handle this situation. Datasheet said nothing
about the reason when/why it happens.
o In vr_newbuf() don't set VR_RXSTAT_FIRSTFRAG/VR_RXSTAT_LASTFRAG
bits as it's set by hardware.
o Don't pass checksum offload information to upper layer for
fragmented frames. The hardware assisted checksum is valid only
when the frame is non-fragmented IP frames. Also mark the checksum
is valid for corrupted frames such that upper layers doesn't need
to recompute the checksum with software routine.
o Removed vr_rxeoc(). RxDMA doesn't seem to need to be idle before
sending VR_CMD_RX_GO command. Previously it used to stop RxDMA
first which in turn resulted in long delays in Rx error recovery.
o Rewrote Tx completion handler.
- Always check VR_TXSTAT_OWN bit in status word prior to
inspecting other status bits in the status word.
- Collision counter updates were corrected as VT3071 or newer
ones use different bits to notify collisions.
- Unlike other chip revisions, VT86C100A uses different bit to
indicate Tx underrun. For VT3071 or newer ones, check both
VR_TXSTAT_TBUFF and VR_TXSTAT_UDF bits to see whether Tx
underrun was happend. In case of Tx underrun requeue the failed
frame and restart stalled Tx SM. Also double Tx DMA threshold
size on each failure to mitigate future Tx underruns.
- Disarm watchdog timer only if we have no queued packets,
otherwise don't touch watchdog timer.
o Rewrote interrupt handler.
- status word in Tx/Rx descriptors indicates more detailed error
state required to recover from the specific error. There is no
need to rely on interrupt status word to recover from Tx/Rx
error except PCI bus error. Other event notifications like
statistics counter overflows or link state events will be
handled in main interrupt handler.
- Don't touch VR_IMR register if we are in suspend mode. Touching
the register may hang the hardware if we are in suspended state.
Previously it seems that touching VR_IMR register in interrupt
handler was to work-around panic occurred in system shutdown
stage on SMP systems. I think that work-around would hide
root-cause of the panic and I couldn't reproduce the panic
with multiple attempts on my box.
o While padding space to meet minimum frame size, zero the pad data
in order to avoid possibly leaking sensitive data.
o Rewrote vr_start_locked().
- Don't try to queue packets if number of available Tx descriptors
are short than that of required one.
o Don't reinitialize hardware whenever media configuration is
changed. Media/link state changes are reported from mii layer if
this happens and vr_link_task() will perform necessary changes.
o Don't reinitialize hardware if only PROMISC bit was changed. Just
toggle the PROMISC bit in hardware is sufficient to reflect the
request.
o Rearrganed the IFCAP_POLLING/IFCAP_HWCSUM handling in vr_ioctl().
o Generate Tx completion interrupts for every VR_TX_INTR_THRESH-th
frames. This reduces Tx completion interrupts under heavy network
loads.
o Since vr(4) doesn't request Tx interrupts for every queued frames,
reclaim any pending descriptors not handled in Tx completion
handler before actually firing up watchdog timeouts.
o Added vr_tx_stop()/vr_rx_stop() to wait for the end of active
TxDMA/RxDMA cycles(draining). These routines are used in vr_stop()
to ensure sane state of MAC before releasing allocated Tx/Rx
buffers. vr_link_task() also takes advantage of these functions to
get to idle state prior to restarting Tx/Rx.
o Added vr_tx_start()/vr_rx_start() to restart Rx/Tx. By separating
Rx operation from Tx operation vr(4) no longer need to full-reset
the hardware in case of Tx/Rx error recovery.
o Implemented WOL.
o Added VT6105M specific register definitions. VT6105M has the
following hardware capabilities.
- Tx/Rx IP/TCP/UDP checksum offload.
- VLAN hardware tag insertion/extraction. Due to lack of information
for getting extracted VLAN tag in Rx path, VLAN hardware support
was not implemented yet.
- CAM(Content Addressable Memory) based 32 entry perfect multicast/
VLAN filtering.
- 8 priority queues.
o Implemented CAM based 32 entry perfect multicast filtering for
VT6105M. If number of multicast entry is greater than 32, vr(4)
uses traditional hash based filtering.
o Reflect real Tx/Rx descriptor structure. Previously vr(4) used to
embed other driver (private) data into these structure. This type
of embedding make it hard to work on LP64 systems.
o Removed unused vr_mii_frame structure and MII bit-baning
definitions.
o Added new PCI configuration registers that controls mii operation
and mode selection.
o Reduced number of Tx/Rx descriptors to 128 from 256. From my
testing, increasing number of descriptors above than 64 didn't help
increasing performance at all. Experimentations show 128 Rx
descriptors seems to help a lot reducing Rx FIFO overruns under
high system loads. It seems the poor Tx performance of Rhine
hardwares comes from the limitation of hardware. You wouldn't
satuarte the link with vr(4) no matter how fast CPU/large number of
descriptors are used.
o Added vr_statistics structure to hold various counter values.
No regression was reported but one variant of Rhine III(VT6105M)
found on RouterBOARD 44 does not work yet(Reported by Milan Obuch).
I hope this would be resolved in near future.
I'd like to say big thanks to Mike Tancsa who kindly donated a Rhine
hardware to me. Without his enthusiastic testing and feedbacks
overhauling vr(4) never have been possible. Also thanks to Masayuki
Murayama who provided some good comments on the hardware's internals.
This driver is result of combined effort of many users who provided
many feedbacks so I'd like to say special thanks to them.
Hardware donated by: Mike Tancsa (mike AT sentex dot net)
Reviewed by: remko (initial version)
Tested by: Mike Tancsa(x86), JoaoBR ( joao AT matik DOT com DOT br )
Marcin Wisnicki ( mwisnicki+freebsd AT gmail DOT com )
Stefan Ehmann ( shoesoft AT gmx DOT net )
Florian Smeets ( flo AT kasimir DOT com )
Phil Oleson ( oz AT nixil DOT net )
Larry Baird ( lab AT gta DOT com )
Milan Obuch ( freebsd-current AT dino DOT sk )
remko (initial version)
VR_STICKHW register would result in unexpected results on these
hardwares. wpaul said the following for the issue.
The vr_attach() routine unconditionally does this for all supported
chips:
/*
* Windows may put the chip in suspend mode when it
* shuts down. Be sure to kick it in the head to wake it
* up again.
*/
VR_CLRBIT(sc, VR_STICKHW, (VR_STICKHW_DS0|VR_STICKHW_DS1));
The problem is, the VR_STICKHW register is not valid on all Rhine
devices. The VT86C100A chip, which is present on the D-Link DFE-530TX
boards, doesn't support power management, and its register space is
only 128 bytes wide. The VR_STICKHW register offset falls outside this
range. This may go unnoticed in most scenarios, but if you happen to have
another PCI device in your system which is assigned the register
space immediately after that of the Rhine, the vr(4) driver will
incorrectly stomp it. In my case, the BIOS on my test board decided
to put the register space for my PRO/100 ethernet board right next
to the Rhine, and the Rhine driver ended up clobbering the IMR register
of the PRO/100 device. (Long story short: the board kept locking up on
boot. Took me the better part of the morning suss out why.)
The strictly correct thing to do would be to check the PCI config space
to make sure the device supports the power management capability and only
write to the VR_STICKHW register if it does.
Instead of inspecting chip revision numbers for the availability of
VR_STICKHW register, check the existence of power management capability
of the hardware as wpaul suggested.
Reported by: wpaul
Suggested by: wpaul
OK'ed by: jhb
The 6105M and 6102 does not have the DWORD alignment problem, so
don't m_defrag() every packet in the transmit path for those.
More stringent usage of tx-descriptor ring and its flags.
Tested on 6102 and 6105M, other chips may also be able to run
without the m_defrag() but I have neither hardware nor docs to
find out.
Sponsored by: Soekris Engineering
if_ioctl, if_watchdog, etc, or in functions that are used by
these methods only. In all other cases use device_printf().
This also fixes several panics, when if_printf() is called before
softc->ifp was initialized.
Submitted by: Alex Lyashkov <umka sevcity.net>
rather than in ifindex_table[]; all (except one) accesses are
through ifp anyway. IF_LLADDR() works faster, and all (except
one) ifaddr_byindex() users were converted to use ifp->if_addr.
- Stop storing a (pointer to) Ethernet address in "struct arpcom",
and drop the IFP2ENADDR() macro; all users have been converted
to use IF_LLADDR() instead.
I had to initialize the ifnet a bit earlier in attach so that the
if_printf()'s in vr_reset() didn't explode with a page fault.
- Use M_ZERO with contigmalloc() rather than an explicit bzero.
opt_device_polling.h
- Include opt_device_polling.h into appropriate files.
- Embrace with HAVE_KERNEL_OPTION_HEADERS the include in the files that
can be compiled as loadable modules.
Reviewed by: bde
o Axe poll in trap.
o Axe IFF_POLLING flag from if_flags.
o Rework revision 1.21 (Giant removal), in such a way that
poll_mtx is not dropped during call to polling handler.
This fixes problem with idle polling.
o Make registration and deregistration from polling in a
functional way, insted of next tick/interrupt.
o Obsolete kern.polling.enable. Polling is turned on/off
with ifconfig.
Detailed kern_poll.c changes:
- Remove polling handler flags, introduced in 1.21. The are not
needed now.
- Forget and do not check if_flags, if_capenable and if_drv_flags.
- Call all registered polling handlers unconditionally.
- Do not drop poll_mtx, when entering polling handlers.
- In ether_poll() NET_LOCK_GIANT prior to locking poll_mtx.
- In netisr_poll() axe the block, where polling code asks drivers
to unregister.
- In netisr_poll() and ether_poll() do polling always, if any
handlers are present.
- In ether_poll_[de]register() remove a lot of error hiding code. Assert
that arguments are correct, instead.
- In ether_poll_[de]register() use standard return values in case of
error or success.
- Introduce poll_switch() that is a sysctl handler for kern.polling.enable.
poll_switch() goes through interface list and enabled/disables polling.
A message that kern.polling.enable is deprecated is printed.
Detailed driver changes:
- On attach driver announces IFCAP_POLLING in if_capabilities, but
not in if_capenable.
- On detach driver calls ether_poll_deregister() if polling is enabled.
- In polling handler driver obtains its lock and checks IFF_DRV_RUNNING
flag. If there is no, then unlocks and returns.
- In ioctl handler driver checks for IFCAP_POLLING flag requested to
be set or cleared. Driver first calls ether_poll_[de]register(), then
obtains driver lock and [dis/en]ables interrupts.
- In interrupt handler driver checks IFCAP_POLLING flag in if_capenable.
If present, then returns.This is important to protect from spurious
interrupts.
Reviewed by: ru, sam, jhb
IFF_DRV_RUNNING, as well as the move from ifnet.if_flags to
ifnet.if_drv_flags. Device drivers are now responsible for
synchronizing access to these flags, as they are in if_drv_flags. This
helps prevent races between the network stack and device driver in
maintaining the interface flags field.
Many __FreeBSD__ and __FreeBSD_version checks maintained and continued;
some less so.
Reviewed by: pjd, bz
MFC after: 7 days
over iteration of their multicast address lists when synchronizing the
hardware address filter with the network stack-maintained list.
Problem reported by: Ed Maste (emaste at phaedrus dot sandvine dot ca>
MFC after: 1 week
struct ifnet or the layer 2 common structure it was embedded in have
been replaced with a struct ifnet pointer to be filled by a call to the
new function, if_alloc(). The layer 2 common structure is also allocated
via if_alloc() based on the interface type. It is hung off the new
struct ifnet member, if_l2com.
This change removes the size of these structures from the kernel ABI and
will allow us to better manage them as interfaces come and go.
Other changes of note:
- Struct arpcom is no longer referenced in normal interface code.
Instead the Ethernet address is accessed via the IFP2ENADDR() macro.
To enforce this ac_enaddr has been renamed to _ac_enaddr.
- The second argument to ether_ifattach is now always the mac address
from driver private storage rather than sometimes being ac_enaddr.
Reviewed by: sobomax, sam
the device is suspended or shutting down. This will need to be rethought
slightly if we implement suspend/resume support within vr(4).
This appears to fix the vr_shutdown() panic on SMP machines.
My theory here is there's a race somewhere during vr_detach() with
vr_intr() in the SMP case which was sometimes being triggered,
although quite why this was happening is unclear (vr_stop() also
explicitly disables interrupts by writing to the IMR register).
MFC-to-RELENG_5* candidate.
PR: kern/62889
Tested by: seb at struchtrup dot com
MFC after: 10 days
as the original logic did. This fixes a race with vr_intr() which was
masked on UP systems and manifested on SMP systems.
PR: kern/62889
MFC after: 1 day
- Add *_locked() entry points as needed to avoid unnecessary lock thrashing.
- Use these entry points wisely.
- Only acquire the lock once when servicing an interrupt.
- Check 'suspended' on interrupt to avoid racing detach.
- Correct a mis-spelled comment.
- Don't take the lock in vr_reset() to avoid lock thrashing in attach.
- Comment this.
Reviewed by: -net (silence)
- Remove recursive locking situations. Remove the MTX_RECURSE bit.
- Take the lock for any routine which is not called from within if_vr.c
itself; this includes entry points called by newbus, ifnet, callout,
ifmedia, and polling subsystems.
- Remove spl references from the code added to miibus callbacks in rev 1.60.
- Add the INTR_MPSAFE bit.
- Tidy up some assignments; locks are not needed for taking the address
of something at a known offset, for example.
- Tested on the machine this was committed from.
Tested on: UP only, !debug.mpsafenet && debug.mpsafenet
Reviewed by: rwatson
Put some braces around the busy-wait loop in vr_rxeoc() to make the
no-op semicolon more obvious.
No functional changes.
Running on the machine I am committing from without problems.
Reviewed by: jmallett
