Just in case that no chimney sending buffer can be used.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8619
This bug has been bugging me for quite some time. I finally sat down
with enough coffee to figure it out.
The short of it - rounding up to the next intval multiple of the TSF value
only works if the AP is transmitting all its beacons on an interval of
the TSF. If it isn't - for example, doing staggered beacons on a multi-VAP
setup with a single hardware TSF - then weird things occur.
The long of it -
When powersave is enabled, the MAC and PHY are partially powered off.
They can't receive any packets (or transmit, for that matter.)
The target beacon timer programming will wake up the MAC/PHY just before
the beacon is supposed to be received (well, strictly speaking, at DTIM
so it can see the TIM - traffic information map - telling the STA whether
any traffic is there for it) and it happens automatically.
However, this relies on the target beacon time being programmed correctly.
If it isn't then the hardware will wake up and not hear any beacons -
and then it'll be asleep for said beacons. After enough of this, net80211
will give up and assume the AP went away.
This should fix both TSFOOR interrupts and disconnects from APs with powersave
enabled.
The annoying bit is that it only happens if APs stagger things or start
on a non-zero TSF. So, this would sometimes be fine and sometimes not be
fine.
What:
* I don't know (yet) why the code rounds up to the next intval.
For now, just disable rounding it and trust the value we get.
TODO:
* If we do see a beacon miss in STA mode then we should transition
out of sleep for a while so we can hear beacons to resync against.
I'd love a patch from someone to enable that particular behaviour.
Note - that doesn't require that net80211 brings the chip out of
sleep state - only that we wake the chip up through to full-on and
then let it go to sleep again when we've seen a beacon. The wifi
stack and AP can still completely just stay believing we're in sleep
mode.
Tested:
* AR9485, STA mode, powersave enabled
MFC after: 1 week
Relnotes: Yes
- Set IEEE80211_FEXT_SCAN_OFFLOAD flag; firmware can send null data
frames when associated.
- Check IEEE80211_SCAN_ACTIVE scan flag instead of IEEE80211_F_ASCAN
ic flag; the last is never set since r170530.
- Eliminate software scan (net80211) <-> site_survey (driver) race:
* override ic_scan_curchan and ic_scan_mindwell pointers so net80211
will not try to finish scanning automatically;
* inform net80211 about current status via ieee80211_cancel_scan()
and ieee80211_scan_done();
* remove corresponding workaround from rsu_join_bss().
Now the driver can associate to an AP with hidden SSID.
Tested with Asus USB-N10.
- Defined an abstract NVRAM I/O API (bhnd_nvram_io), decoupling NVRAM/SPROM
parsing from the actual underlying NVRAM data provider (e.g. CFE firmware
devices).
- Defined an abstract NVRAM data API (bhnd_nvram_data), decoupling
higher-level NVRAM operations (indexed lookup, data conversion, etc) from
the underlying NVRAM file format parsing/serialization.
- Implemented a new high-level bhnd_nvram_store API, providing indexed
variable lookup, pending write tracking, etc on top of an arbitrary
bhnd_nvram_data instance.
- Migrated all bhnd(4) NVRAM device drivers to the common bhnd_nvram_store
API.
- Implemented a common bhnd_nvram_val API for parsing/encoding NVRAM
variable values, including applying format-specific behavior when
converting to/from the NVRAM string representations.
- Dropped the now unnecessary bhnd_nvram driver, and moved the
broadcom/mips-specific CFE NVRAM driver out into sys/mips/broadcom.
- Implemented a new nvram_map file format:
- Variable definitions are now defined separately from the SPROM
layout. This will also allow us to define CIS tuple NVRAM
mappings referencing the common NVRAM variable definitions.
- Variables can now be defined within arbitrary named groups.
- Textual descriptions and help information can be defined inline
for both variables and variable groups.
- Implemented a new, compact encoding of SPROM image layout
offsets.
- Source-level (but not build system) support for building the NVRAM file
format APIs (bhnd_nvram_io, bhnd_nvram_data, bhnd_nvram_store) as a
userspace library.
The new compact SPROM image layout encoding is loosely modeled on Apple
dyld compressed LINKEDIT symbol binding opcodes; it provides a compact
state-machine encoding of the mapping between NVRAM variables and the SPROM
image offset, mask, and shift instructions necessary to decode or encode
the SPROM variable data.
The compact encoding reduces the size of the generated SPROM layout data
from roughly 60KB to 3KB. The sequential nature SPROM layout opcode tables
also simplify iteration of the SPROM variables, as it's no longer
neccessary to iterate the full NVRAM variable definition table, but
instead simply scan the SPROM revision's layout opcode table.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D8645
So that the caller can know the channel close error and react accordingly.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8600
So that the callers of vmbus_chan_open_br() could handle the passed in
bufring memory properly.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8569
vmbus_pcib requires NEW_PCIB, but in case that's not defined, we at
least shouldn't break build.
Reviewed by: sephe
Approved by: sephe (mentor)
MFC after: 3 days
Sponsored by: Microsoft
Queues that do not need interrupts - for instance, output queues - do
not have a corresponding entry in vtpci_msix_vq_interrupts.
So, it was wrong to increment a pointer into that array when iterating
over such a queue.
I ran into this bug while trying to use virtio_console(4) that allocates
a lot of queues with every other being an output queue without an
interrupt handler (if MultiplePorts feature is negotiated).
MFC after: 2 weeks
Zero can be confused for a potentially valid value.
For example, if I load and unload sbp driver I get a lot of messages
like the following:
fw_tl_free: the xfer is not in the queue (tlabel=0, flag=0x0)
send: dst=0x00 tl=0x00 rt=0 tcode=0x0 pri=0x0 src=0x000
recv: dst=0x01 tl=0x21 rt=1 tcode=0x1 pri=0x0 src=0xffc0
KDB: stack backtrace:
db_trace_self_wrapper() at db_trace_self_wrapper+0x2b/frame 0xfffffe04464407e0
fw_tl_free() at fw_tl_free+0x18d/frame 0xfffffe0446440820
fw_xfer_unload() at fw_xfer_unload+0xca/frame 0xfffffe0446440840
fw_xferlist_remove() at fw_xferlist_remove+0x2f/frame 0xfffffe0446440870
sbp_detach() at sbp_detach+0x1e0/frame 0xfffffe04464408e0
device_detach() at device_detach+0x80/frame 0xfffffe0446440900
devclass_driver_deleted() at devclass_driver_deleted+0x6a/frame 0xfffffe0446440940
devclass_delete_driver() at devclass_delete_driver+0x7d/frame 0xfffffe0446440980
driver_module_handler() at driver_module_handler+0xff/frame 0xfffffe04464409d0
module_unload() at module_unload+0x32/frame 0xfffffe04464409f0
linker_file_unload() at linker_file_unload+0x24b/frame 0xfffffe0446440a40
kern_kldunload() at kern_kldunload+0xbc/frame 0xfffffe0446440a70
amd64_syscall() at amd64_syscall+0x314/frame 0xfffffe0446440bf0
Xfast_syscall() at Xfast_syscall+0xfb/frame 0xfffffe0446440bf0
MFC after: 2 weeks
Please see section 5.15 of 1394 OHCI Specification.
If the register is not implemented, then the physical response unit is
limited to the first 4GB of the physical memory.
In that case the non-cooperative debugging over firewire (using /dev/fwmem)
can not be expected to work if a target has more RAM than that.
The method is described in gdb.4 and the Developer's Handbook.
It seems that most of the consumer hardware does not implement
PhysicalUpperBound register.
MFC after: 1 week
Since hypervisor will not drain the TX bufring, once the channels are
revoked:
- Setup vmbus orphan handler properly.
- Make sure that suspension will not wait the TX bufring draining
forever.
- GC the pending TX descs on detach path, before freeing the busdma
stuffs.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8559
- Reference count the sub-channel when channel offer message is
processed, so that immediate rescind message on the same channel
will not race sub-channel open on driver side.
- Drop the above reference when sub-channel is closed, this closely
mimics the hypervisor's reaction when primary channel is closed
on the VM side. No drivers use sub-channel after primary channel
is closed.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8546
Drivers can now use vmbus_chan_{is_revoked,set_orphan,unset_orphan}() and
vmbus_xact_ctx_orphan() to fix their attach/detach DEVMETHODs for revoked
primary channels.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8545
It will be used to fix the primary channel revocation support.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8525
These functions are only used by management stuffs, so there are
no needs to introduce extra complexity.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8524
This will be used to fix device detach DEVMETHOD for revoked primary
channel.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8522
Minimal impact, would allow selection of LR media when KR is connected.
Reported by: Coverity
Approved by: davidch
MFC after: 7 days
Sponsored by: Broadcom Limited
* Obey the peer A-MPDU density if it's larger than the currently configured
one.
* Pay attention to the peer A-MPDU max-size and don't assume we can transmit
a full A-MPDU (64k!) if the peer announces smaller values.
Relnotes: ath(4): Fix A-MPDU transmit; obey A-MPDU density and max size.
This patch allows to specify PHY register offset for ukswitch. For instance,
switch MAICREL KS8995XA connected via MDIO to SoC, but PHY register starts
at 1. So hint for this case is: hint.ukswitch.0.phyoffset=1
No change/effect if hint is not set.
Submitted by: Hiroki Mori <yamori813@yahoo.co.jp>
Reviewed by: adrian, mizhka
Approved by: adrian(mentor)
Differential Revision: https://reviews.freebsd.org/D8584