Many things have been changing in the kernel since mid-1996, so there's
quite some amount of diffs here already. It compiles, but i cannot
test it anywhere here.
2.2 candidate?
Closes PR # 1201.
from last time. Some people have pointed out that there were some odd
side-effects in the changes I made. Two things are different:
- sc_print_addr() will print 'foodev0:' (i.e. sd0:, st0:, cd0:, etc...)
if the device name is known. If it's not known, it'll use a longer
notation. This shortens error messages back to a sane length.
- Added a small function called sc_print_init() to set the sc_printing
flag so that sc_print_addr() will know that we want it to print a
linefeed. Used this in scsi_device_attach() to restore proper carriage
return printing behavior which I broke.
Remaining bogons: the NCR SCSI driver prints out information while the
device-specific attach routine is running with its own linefeeds. This
breaks up the individual messages emitted by the subdriver modules and
causes at least one message to appear on a line by itself without a
device spec prefix. I'm not sure of the correct way to fix this, and
I don't have any NCR SCSI hardware to test with anyway.
There's probably more, but I gather that a rewrite of the SCSI subsystem
is pending anyway, so I'll leave the rest to Those Who Know More About
This Than I (tm).
(since T_DIRECT just incidentally happens to be equal 0). This causes
more harm than it would do good. Instead , get it at the uk driver.
Reviewed by: obrien@NUXI.com (David O'Brien)
("Hey! Who made _you_ the keeper of all things BSDish?!") but this has
bugged me for a long time, and now that I finally have the chance
to hack on it (and test the results), I'll take my chances. I can also
point to other BSD implementations for precedents if you put my back to
the wall.
The only thing that's changed is how the messages are formatted. Now,
instead of having this:
aha0 at 0x330-0x333 irq 11 drq 5 on isa
(aha0:3:0): "HP C1553A 9503" type 1 removable SCSI 2
st0(aha0:3:0): Sequential-Access density code 0x24, variable blocks, write-enabled
(aha0:3:1): "HP C1553A 9503" type 8 removable SCSI 2
ch0(aha0:3:1): Medium-Changer 6 slot(s) 1 drive(s) 0 arm(s) 0 i/e-slot(s)
We have this:
aha0 at 0x330-0x333 irq 11 drq 5 on isa
scbus0 at aha0 bus 0
st0 at scbus0 target 3 lun 0
st0: <HP C1553A 9503> type 1 removable SCSI 2
st0: Sequential-Access density code 0x24, variable blocks, write-enabled
ch0 at scbus0 target 3 lun 1
ch0: <HP C1553A 9503> type 8 removable SCSI 2
ch0: Medium-Changer 6 slot(s) 1 drive(s) 0 arm(s) 0 i/e-slot(s)
Which is (to me anyway) is a lot more pleasant to look at. (Call me
crazy -- g'head: you know you wanna -- but the previous messages remind
me of Linux. Ever see the output from the linux device probes? It's a mess
of copyright notices, version numbers/dates, author e-mail addresses and
other crap. Let's not go there, okay? Bleh.)
Notice that devices are now specified in terms of the scsi bus they
live on rather than the adapter. This better reflects the contents
of the kernel config file (if you use wired-down device specifications
anyway) and removes some ambiguity that may arise if you have a multi-
channel adapter with more than one bus.
Also, sc_print_addr() now generates messages like this:
st0 at scbus0 target 3 lun 0: NOT READY asc:3a,0 Medium not present
instead of this:
st0(aha0:3:0): NOT READY asc:3a,0 Medium not present
I also added a quirk entry for the HP Superstore 12000e 6 tape DAT
autoloader, which needs SC_MORE_LUS in order for the changer device
to be properly probed and attached. (I'm working on a chcontrol utility
to manipulate the changer on this drive which should hopefully be general
enough to work with other changers too. If you want the prototype I have
now, it's at ftp://skynet.ctr.columbia.edu/pub/freebsd/changer.c.)
Remaining bugs:
- The 'foodev0: yadda yadda yadda' bits should probably be printed entirely
by the device-specific subdriver attach code instead of half by the
scsi_device_attach() routine and half by the device specific attach
routine like it is now.
- The wired-down device specifications in the kernel config file should
be used to control bus/device probing to some extent rather than just
for choosing names for devices we find. If the config says there's a
device at scbus0 target 0 lun 0 called sd0, we should look there and
check for a device that can be managed by the sd driver. If we don't
find one, we should probably complain that there's no device there or
that there is a device but of the wrong type. Once all the devices from
the wired down list have been probed, the code can then autodetect and
autoattach any devices that remain unassigned.
- Apparently some tape changers (hi Ulf!) return 'not ready/medium not
present' when the magazine is loaded but a tape has not been put in the
drive yet. This causes an open(/dev/ch0) to fail and prevents you from
using the changer.c utility to load the first tape into the drive. My
HP changer does not behave this way. The workaround is to manually load
a tape into the drive before attempting to use the changer program, but
you can get in trouble if you accidentally eject a tape without loading
a new one and you're at a remote location: you won't be able to load
any tapes anymore. I'm not sure what the correct software solution is
for this but ideally there should be one.
- I should not be doing this: I'm the NIS guru, not the SCSI guru.
(This is not my beautiful code. How did I get here? My god: what
have I done?)
This will make a number of things easier in the future, as well as (finally!)
avoiding the Id-smashing problem which has plagued developers for so long.
Boy, I'm glad we're not using sup anymore. This update would have been
insane otherwise.
series drives, and add the NAKAMICHI MO drive RMD-5200-S.
Closes PR # kern/2200: Change/Add new optical di...
Submitted by: akiyama@kme.mei.co.jp (Shunsuke Akiyama)
. also detect the Phlips CDD2000; it's software-compatible with the HP part
Submitted by: cau@cc.gatech.edu (Carlos Ugarte)
. correct the blocksize handling for CD-DA tracks, and fix multitrack
handling
Submitted by: nsayer@quack.kfu.com (Nick Sayer)
2.2 candidates!
All new code is "#ifdef PC98"ed so this should make no difference to
PC/AT (and its clones) users.
Ok'd by: core
Submitted by: FreeBSD(98) development team
drives require ST_Q_SNS_HLP, they also wrongly accept a blocksize of
1024 in the first place (for a QIC-150 cartridge), but complain later
about it. The hack is to only probe for 512 for them.
Reorder the entries in st_decide_mode() so that QIC >= 525 is properly
accepted as variable blocksize.
seems to work hre just fine though I can't check every file
that changed due to limmited h/w, however I've checked enught to be petty
happy withe hte code..
WARNING... struct lkm[mumble] has changed
so it might be an idea to recompile any lkm related programs
It will need to be changed
but it's the better starting point..
also add '?' to wildcarding in SCSI identification of devices..
so we can catch all PIONEER CD 6??* devices instead of having
separate entries for the 600, 602, 604X, 624X etc..
it's getting so we should have a small regexp routine in the kernel
maybe just a little one.. matching CDX-6[0-9][0-9][ A-Z] would be better
there will be drastic changes in this
but this is the best starting point..
Convert the remaining sysctl stuff to the new way of doing things.
the devconf stuff is the reason for the large number of files.
Cleaned up some compiler warnings while I were there.
itself. Will do this after this commit.)
Make scsiconf more flexible about recognizing ``foreign'' devices.
This part needs to be rewritten some day to allow for matches whithou
strict version number checks, but either Julian as Peter seem to be
too busy right now, so i'm finally commiting the version that's
working for me stable now for several months, as an interim
workaround.
Submitted by: akiyama@kme.mei.co.jp (Shunsuke Akiyama)
o don't use polled mode after the device probe phase
o don't biodone() a NULL buffer pointer
o increase the timeout for scsi_read_capacity(); WORMs are slooow
o make WORMMs known to scsiconf at all
This brings the driver in a state where it at least doesn't
immediately panic, nor hangs the controller any more. Unfortunately,
at least the YAMAHA CDR100 i've been testing with answered my write
attempts with an "Incorrect command sequence" response. Perhaps other
CD burners might work however.
Reviewed by: dufault
