(reporting IFM_LOOP based on BMCR_LOOP is left in place though as
it might provide useful for debugging). For most mii(4) drivers it
was unclear whether the PHYs driven by them actually support
loopback or not. Moreover, typically loopback mode also needs to
be activated on the MAC, which none of the Ethernet drivers using
mii(4) implements. Given that loopback media has no real use (and
obviously hardly had a chance to actually work) besides for driver
development (which just loopback mode should be sufficient for
though, i.e one doesn't necessary need support for loopback media)
support for it is just dropped as both NetBSD and OpenBSD already
did quite some time ago.
- Let mii_phy_add_media() also announce the support of IFM_NONE.
- Restructure the PHY entry points to use a structure of entry points
instead of discrete function pointers, and extend this to include
a "reset" entry point. Make sure any PHY-specific reset routine is
always used, and provide one for lxtphy(4) which disables MII
interrupts (as is done for a few other PHYs we have drivers for).
This includes changing NIC drivers which previously just called the
generic mii_phy_reset() to now actually call the PHY-specific reset
routine, which might be crucial in some cases. While at it, the
redundant checks in these NIC drivers for mii->mii_instance not being
zero before calling the reset routines were removed because as soon
as one PHY driver attaches mii->mii_instance is incremented and we
hardly can end up in their media change callbacks etc if no PHY driver
has attached as mii_attach() would have failed in that case and not
attach a miibus(4) instance.
Consequently, NIC drivers now no longer should call mii_phy_reset()
directly, so it was removed from EXPORT_SYMS.
- Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe().
The purpose of that function is to perform the common steps to attach
a PHY driver instance and to hook it up to the miibus(4) instance and to
optionally also handle the probing, addition and initialization of the
supported media. So all a PHY driver without any special requirements
has to do in its bus attach method is to call mii_phy_dev_attach()
along with PHY-specific MIIF_* flags, a pointer to its PHY functions
and the add_media set to one. All PHY drivers were updated to take
advantage of mii_phy_dev_attach() as appropriate. Along with these
changes the capability mask was added to the mii_softc structure so
PHY drivers taking advantage of mii_phy_dev_attach() but still
handling media on their own do not need to fiddle with the MII attach
arguments anyway.
- Keep track of the PHY offset in the mii_softc structure. This is done
for compatibility with NetBSD/OpenBSD.
- Keep track of the PHY's OUI, model and revision in the mii_softc
structure. Several PHY drivers require this information also after
attaching and previously had to wrap their own softc around mii_softc.
NetBSD/OpenBSD also keep track of the model and revision on their
mii_softc structure. All PHY drivers were updated to take advantage
as appropriate.
- Convert the mebers of the MII data structure to unsigned where
appropriate. This is partly inspired by NetBSD/OpenBSD.
- According to IEEE 802.3-2002 the bits actually have to be reversed
when mapping an OUI to the MII ID registers. All PHY drivers and
miidevs where changed as necessary. Actually this now again allows to
largely share miidevs with NetBSD, which fixed this problem already
9 years ago. Consequently miidevs was synced as far as possible.
- Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that
weren't explicitly converted to support flow control before. It's
unclear whether flow control actually works with these but typically
it should and their net behavior should be more correct with these
changes in place than without if the MAC driver sets MIIF_DOPAUSE.
Obtained from: NetBSD (partially)
Reviewed by: yongari (earlier version), silence on arch@ and net@
driver would verify that requests for child devices were confined to any
existing I/O windows, but the driver relied on the firmware to initialize
the windows and would never grow the windows for new requests. Now the
driver actively manages the I/O windows.
This is implemented by allocating a bus resource for each I/O window from
the parent PCI bus and suballocating that resource to child devices. The
suballocations are managed by creating an rman for each I/O window. The
suballocated resources are mapped by passing the bus_activate_resource()
call up to the parent PCI bus. Windows are grown when needed by using
bus_adjust_resource() to adjust the resource allocated from the parent PCI
bus. If the adjust request succeeds, the window is adjusted and the
suballocation request for the child device is retried.
When growing a window, the rman_first_free_region() and
rman_last_free_region() routines are used to determine if the front or
end of the existing I/O window is free. From using that, the smallest
ranges that need to be added to either the front or back of the window
are computed. The driver will first try to grow the window in whichever
direction requires the smallest growth first followed by the other
direction if that fails.
Subtractive bridges will first attempt to satisfy requests for child
resources from I/O windows (including attempts to grow the windows). If
that fails, the request is passed up to the parent PCI bus directly
however.
The PCI-PCI bridge driver will try to use firmware-assigned ranges for
child BARs first and only allocate a "fresh" range if that specific range
cannot be accommodated in the I/O window. This allows systems where the
firmware assigns resources during boot but later wipes the I/O windows
(some ACPI BIOSen are known to do this) to "rediscover" the original I/O
window ranges.
The ACPI Host-PCI bridge driver has been adjusted to correctly honor
hw.acpi.host_mem_start and the I/O port equivalent when a PCI-PCI bridge
makes a wildcard request for an I/O window range.
The new PCI-PCI bridge driver is only enabled if the NEW_PCIB kernel option
is enabled. This is a transition aide to allow platforms that do not
yet support bus_activate_resource() and bus_adjust_resource() in their
Host-PCI bridge drivers (and possibly other drivers as needed) to use the
old driver for now. Once all platforms support the new driver, the
kernel option and old driver will be removed.
PR: kern/143874 kern/149306
Tested by: mav
Rationale:
- unlike current behavior this seems to be compliant with OSS
specification:
http://manuals.opensound.com/developer/SNDCTL_DSP_GETIPTR.html
- this seems to meet expectations of some OSS programs compiled for or
ported from Linux, e.g. ALSA OSS plugin
- this doesn't seem to break any programs as far as current testing
shows
Tested by: nox, hselasky
MFC after: 4 days
structure, which acts as a proxy between them. This makes jail rules
persistent, i.e. they can be added before jail gets created, and they
don't disappear when the jail gets destroyed.
and our users complained when broken.
Similarly add LINT-NOINET, and for at least documentation purposes add
LINT-NOIP (which compiles out INET and INET6 and couple of NIC drivers).
Tested by: make universe (if you broke it since you fix it)
Reviewed by: gnn
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 2 weeks
buffer fills up causing the remote sender to enter into persist mode, but
there is still room available in the receive buffer when a window probe
arrives (either due to window scaling, or due to the local application
very slowing draining data from the receive buffer), then the single byte
of data in the window probe is accepted. However, this can cause rcv_nxt
to be greater than rcv_adv. This condition will only last until the next
ACK packet is pushed out via tcp_output(), and since the previous ACK
advertised a zero window, the ACK should be pushed out while the TCP
pcb is write-locked.
During the window while rcv_nxt is greather than rcv_adv, a few places
would compute the remaining receive window via rcv_adv - rcv_nxt.
However, this value was then (uint32_t)-1. On a 64 bit machine this
could expand to a positive 2^32 - 1 when cast to a long. In particular,
when calculating the receive window in tcp_output(), the result would be
that the receive window was computed as 2^32 - 1 resulting in advertising
a far larger window to the remote peer than actually existed.
Fix various places that compute the remaining receive window to either
assert that it is not negative (i.e. rcv_nxt <= rcv_adv), or treat the
window as full if rcv_nxt is greather than rcv_adv.
Reviewed by: bz
MFC after: 1 month
of the 61 bits available within the region for virtual addressing. Since
there's no good way for us to map out the gap in the virtual address space,
limit KVA to the architectural minimum implemented address bits. This still
gives us 1 petabyte of KVA, so no worries.
developers committing new code with broken include directories.
Fix a few whitespace issues.
Improve a couple of comments.
-W is now deprecated and is referred to as -Wextra (see gcc(1)).
Submitted by: arundel
of endian-ness issues with the AR724x.
From Luiz:
* Fix the bus space tag used so endian-ness is correctly handled;
* Only do the workaround for the AR7240; AR7241/AR7242 (PB92)
don't require this
From me:
* Add a read flush from openwrt
Submitted by: Luiz Otavio O Souza
use the PBVM. This eliminates the implied hardcoding of the
physical address at which the kernel needs to be loaded. Using the
PBVM makes it possible to load the kernel irrespective of the
physical memory organization and allows us to replicate kernel text
on NUMA machines.
While here, reduce the direct-mapped page size to the kernel's
page size so that we can support memory attributes better.
kernel configurations to apply WITH_* WITHOUT_* knobs we use for
module building as well to restrict or control opt_*.h flags.
Reviewed by: imp, +
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 2 weeks
