Each different radio chipset has a different "good" range of CCA
(clear channel access) parameters where, if you write something
out of range, it's possible the radio will go deaf.
Also, since apparently occasionally reading the NF calibration
returns "wrong" values, so enforce those limits on what is being
written into the CCA register.
Write a default value if there's no history available.
This isn't the case right now but it may be later on when "off-channel"
scanning occurs without init'ing or changing the NF history buffer.
(As each channel may have a different noise floor; so scanning or
other off-channel activity shouldn't affect the NF history of
the current channel.)
* I messed up a couple of things in if_athvar.h; so fix that.
* Undo some guesswork done in ar5416Set11nRateScenario() and introduce a
flags parameter which lets the caller set a few things. To begin with,
this includes whether to do RTS or CTS protection.
* If both RTS and CTS is set, only do RTS. Both RTS and CTS shouldn't be
set on a frame.
The defaults enabled three chains on the AR5416 even if the card has two
chains. This restores that and ensures that only the correct TX/RX
chainmasks are used.
When HT modes are enabled, all TX chains will be correctly enabled.
This should now enable analog chain swapping with 2-chain cards.
I'm not sure if this is needed for just the AR5416 or whether
it also applies to AR9160, AR9280 and AR9287 (later on); I'll have
to get clarification.
ath9k does a few different things here during config - if it's an early
AR5416 with two chains, it enables all three chains for calibration and
then restores the chainmask to the original values after initial
calibration has completed.
The reason behind this commit is to begin breaking out the chainmask
configuration for this specific reason; follow-up commits will add
the chainmask restore in the ar5416Reset() routine.
The linux ath9k driver and (from what I've been told) the atheros reference
driver does this; it then leaves discarding 11n frames to the 802.11 layer.
Whilst I'm here, merge in a fix from ath9k which maintains a turbo register
setting when enabling the 11n register; and remove an un-needed (duplicate)
flag setting.
The rxmonitor hook is called on each received packet. This can get very,
very busy as the tx/rx/chanbusy registers are thus read each time a packet
is received.
Instead, shuffle out the true per-packet processing which is needed and move
the rest of the ANI processing into a periodic event which runs every 100ms
by default.
sys/dev/ath/ath_hal/ar5416/ is getting very crowded and further
commits will make it even more crowded. Now is a good time to
shuffle these files out before any more extensive work is done
on them.
Create an ar9003 directory whilst I'm here; ar9003 specific
chipset code will eventually live there.
with these ADC DC Gain/Offset calibrations.
The whole idea is to calibrate a pair of ADCs to compensate for any
differences between them.
The AR5416 returns lots of garbage, so there's no need to do the
calibration there.
The AR9160 returns 0 for secondary ADCs when calibrating 2.4ghz 20mhz
modes. It returns valid data for the secondary ADCs when calibrating
2.4ghz HT/40 and any 5ghz mode.
The AR9100 at least doesn't have an external serial EEPROM
attached to the MAC; it instead stores the calibration data
in the normal system flash.
I believe earlier parts can do something similar but I haven't
experienced it first-hand.
This commit introduces an eepromdata pointer into the API but
doesn't at all commit to using it. A future commit will
include the glue needed to allow the AR9100 support code
to use this data pointer as the EEPROM.
the completion schedule from the hardware and returns AH_TRUE if
the hardware supports multi-rate retries (AR5212 and above); and
returns AH_FALSE if the hardware doesn't support multi-rate retries.
The sample rate module directly reads the TX completion descriptor
and extracts the TX schedule information from that. It will be
updated in a future commit to instead use this method to determine
the completion schedule.
If it does, don't then try reprogramming the NF "cap" values (ie
what values are the "maximum" value the NF can be) - instead,
just leave the current CCA value as the NF cap.
This was inspired by some similar work from ath9k. It isn't
a 100% complete solution (as there may be some reason where a
high NF CCA/cap is written, causing the baseband to stop thinking it
is able to transmit, leading to stuck beacon and interface reset)
which I'll investigate and look at fixing in a later commit.
Obtained from: Linux
AR5416 and later chipsets.
ath_hal_calibrateN() calls the HAL calibrateN function with rxchainmask=0x1.
This is not necessarily the case for AR5416 and later chipsets.
o rename the new variables to comply with the naming scheme
o move the new variables to an AR5212 specific struct
o use ahp when available
o revert to previous ts_flags check