alpha: tap driver, accept_filters, ata support for ATA100,
routed update to 2.22, truncate(1), syslogd(8) -n option, kenv(1),
periodic(8) controlled by periodic.conf, logger(1) support for
remote syslogs.
i386: tap driver, accept_filters, ata support for ATA100,
routed update to 2.22, truncate(1), syslogd(8) -n option, kenv(1),
periodic(8) controlled by periodic.conf, boot98cfg(8),
logger(1) support for remote syslogs.
PR: 20628
Submitted by: bmah@cisco.com (Bruce A. Mah)
Reviewed by: nik
Beyond changes to the build system, this includes fixing up the sample
freebsd.mc configuration for changes in defaults and syntax, removing
outdated documentation, and updating the release notes.
1. Correct FTP site for 4.0-stable snapshots and delete sentence
fragment immediately following.
[ not applicable to HEAD ]
2. Add FDDI section to table of contents (see #5 below) and add
one line of whitespace.
3. In userland section, document csh->tcsh, more->less, and
colorized ls.
4. In Ethernet section, do:
s/gigabit ethernet/Gigabit Ethernet/
s/fast ethernet/Fast Ethernet/
s/ethernet/Ethernet/
5. Pull DEC DEFPA/DEFEA *FDDI* cards out of the *Ethernet* section
and into their own second-level section.
6. Add missing period in section header in ATM section.
7. Tweak upgrading sectio with some new text, not sure if this is
much better though.
8. Add a blurb about the -stable mailing list.
[ changed to -current list in HEAD ]
PR: 20015
Submitted by: Bruce A. Mah <bmah@cisco.com>
- Add a note about supporting USB out of the box during installs and
beyond.
- Add a note about the changes to the i386 bootstrap to work around the
1024 cylinder problem. Note that boot0 is now 2 sectors long.
Reminded by: kkenn
controller chip. This chip is currently being used on the NetGear
FA312-TX adapter, which I guess is a replacement for the FA310-TX
(PNIC-based).
I added support for this chip by modifying the sis driver since
the SiS 900 and the NS DP83815 have almost the same programming
interface (the RX filter programming and PHY access methods are
different, but the general configuration, DMA scheme and register
layout are identical).
I would have had this done a lot sooner, but getting the damn MAC
address out of the EEPROM proved to be more complicated than expected.
NICs. (Finally!) The PCMCIA, ISA and PCI varieties are all supported,
though only the ISA and PCI ones will work on the alpha for now.
PCCARD, ISA and PCI attachments are all provided. Also provided an
ancontrol(8) utility for configuring the NIC, man pages, and updated
pccard.conf.sample. ISA cards are supported in both ISA PnP and hard-wired
mode, although you must configure the kernel explicitly to support the
hardwired mode since you have to know the I/O address and port ahead
of time.
Special thanks to Doug Ambrisko for doing the initial newbus hackery
and getting it to work in infrastructure mode.
USB-EL1202A chipset. Between this and the other two drivers, we should
have support for pretty much every USB ethernet adapter on the market.
The only other USB chip that I know of is the SMC USB97C196, and right
now I don't know of any adapters that use it (including the ones made
by SMC :/ ).
Note that the CATC chip supports a nifty feature: read and write combining.
This allows multiple ethernet packets to be transfered in a single USB
bulk in/out transaction. However I'm again having trouble with large
bulk in transfers like I did with the ADMtek chip, which leads me to
believe that our USB stack needs some work before we can really make
use of this feature. When/if things improve, I intend to revisit the
aue and cue drivers. For now, I've lost enough sanity points.