ethernet controller. The driver has been tested with the LinkSys
USB200M adapter. I know for a fact that there are other devices out
there with this chip but don't have all the USB vendor/device IDs.
Note: I'm not sure if this will force the driver to end up in the
install kernel image or not. Special magic needs to be done to exclude
it to keep the boot floppies from bloating again, someone please
advise.
other initializations succeeded.
- Initialize the TX and RX rings in epic_attach() rather than in
epic_init() where we're not supposed to fail. Similarly, free
the TX and RX rings in epic_detach() rather than in epic_stop().
- Change epic_init() to be a void function now that it can't fail.
Also change its parameter to a void * so that we have a correct
prototype for if_init.
- Now that epic_init() has a correct prototype, don't cast the
function pointer when initializing if_init.
- Fix nearby style bugs.
- Don't initialize if_output, ether_ifattach() does this for us.
- Use pci_enable_busmaster() instead of using pci_read_config()
and pci_write_config() directly.
- Don't try to enable I/O, bus_alloc_resource() does this for us.
- Unconditionally call *_stop() if device is in the tree. This is to
prevent callouts from happening after the device is gone. Checks for
bus_child_present() should be added in the future to keep from touching
potentially non-existent hardware in *_detach(). Found by iedowse@.
- Always check for and free miibus children, even if the device is not in
the tree since some failure cases could have gotten here.
- Call ether_ifdetach() in the irq setup failure case
- ti(4), xl(4): move ifmedia_init() calls to the beginning of attach so
that ifmedia_removeall() can be unconditionally called on detach. There
is no way to detect whether ifmedia has been initialized without using
a separate variable (as tl(4) does).
- Add comments to indicate assumptions of code path
bytes_in_mbuf rather than MCLBYTES. Add the ethertnet header to the
front of the mbuf. Adjust bytes_in_mbuf inside the loop that reads
the packet out of the card.
codec during initialization. This code mirrors the reset code used on
the VIA82c686 and fixes a codec initialization failure (SoundMAX
AD1885) reported by Matthias Schuendehuette.
in dc_detach() instead of only calling it if the hardware is preset.
This is a workaround for page faults in softclock() after a `dc'
device was detached, caused by not disabling a timer before freeing
its memory. The bus_child_present() checks should probably be
re-added later, but only to avoid the hardware accesses and not the
other resource cleanups in dc_stop().
Approved by: njl
Many internal structure changes for the FireWire driver.
- Compute CRC in CROM parsing.
- Add support for configuration ROM build.
- Simplify dummy buffer handling.
- busdma conversion
- Use swi_taskqueue_giant for -current. Mark the interrupt routine as MPSAFE.
- AR buffer handling.
Don't reallocate AR buffer but just recycle it.
Don't malloc and copy per packet in fwohci_arcv().
Pass packet to fw_rcv() using iovec.
Application must prepare receiving buffer in advance.
- Change fw_bind API so that application should pre-allocate xfer structure.
- Add fw_xfer_unload() for recycling struct fw_xfer.
- Add post_busreset hook
- Remove unused 'sub' and 'act_type' in struct fw_xfer.
- Remove npacket from struct fw_bulkxfer.
- Don't call back handlers in fwochi_arcv() if the packet has
not drained in AT queue
- Make firewire works on big endian platform.
- Use native endian for packet header and remove unnecessary ntohX/htonX.
- Remove FWXFERQ_PACKET mode. We don't use it anymore.
- Remove unnecessary restriction of FWSTMAXCHUNK.
- Don't set root node for phy config packet if the root node is
not cycle master capable but set myself for root node.
We should be the root node after next bus reset.
Spotted by: Yoshihiro Tabira <tabira@scd.mei.co.jp>
- Improve self id handling
Tested on: i386, sparc64 and i386 with forced bounce buffer
command config register. At the present, this represents a nop
because these bits should have been set earlier in the process. In
the future, we'll only set these bits when the driver requests the
resource, not when the bus code detects the resource.
Reviewed by: mdodd
network layer (ether).
- Don't abuse module names to facilitate ifconfig module loading;
such abuse isn't really needed. (And if we do need type information
associated with a module then we should make it explicit and not
use hacks.)
PCIM_CMD_MEMEN and PCIM_CMD_BUSMASTEREN, becaise some braindead
BIOSes (such as one found in my vprmatrix notebook) forget
to initialize it properly resulting in attachment failure.
