As part of an effort to extend Book-E to the 64-bit world, make the necessary
changes to the DPAA/dTSEC driver set to be integer-pointer conversion clean.
This means no more casts to int, and use uintptr_t where needed.
Since the NCSW source is effectively obsolete, direct changes to the source tree
are safe.
This was found while reworking the device tree nodes for dtsec to match the
Linux device tree. Instead of waiting and expecting later code to call
dpaa_portal_map_registers(), do the equivalent immediately upon mapping.
Otherwise, it's possible to access the pages before that function is called, and
hang the CPU.
BMan and QMan will do this at attach time. Even though the registers are mapped
now, dpaa_portal_map_registers() will be called at BMan and QMan attach time,
updating the mappings to be private, and in the case of cache-enabled registers,
marked as coherent memory mappings.
Summary:
PowerPC Book-E SMP is currently broken for unknown reasons. Pull in
Semihalf changes made c2012 for e500mc/e5500, which enables booting SMP.
This eliminates the shared software TLB1 table, replacing it with
tlb1_read_entry() function.
This does not yet support ePAPR SMP booting, and doesn't handle resetting CPUs
already released (ePAPR boot releases APs to a spin loop waiting on a specific
address). This will be addressed in the near future by using the MPIC to reset
the AP into our own alternate boot address.
This does include a change to the dpaa/dtsec(4) driver, to mark the portals as
CPU-private.
Test Plan:
Tested on Amiga X5000/20 (P5020). Boots, prints the following
messages:
Adding CPU 0, pir=0, awake=1
Waking up CPU 1 (dev=1)
Adding CPU 1, pir=20, awake=1
SMP: AP CPU #1 launched
top(1) shows CPU1 active.
Obtained from: Semihalf
Relnotes: Yes
Differential Revision: https://reviews.freebsd.org/D5945
Freescale's QorIQ line includes a new ethernet controller, based on their
Datapath Acceleration Architecture (DPAA). This uses a combination of a Frame
manager, Buffer manager, and Queue manager to improve performance across all
interfaces by being able to pass data directly between hardware acceleration
interfaces.
As part of this import, Freescale's Netcomm Software (ncsw) driver is imported.
This was an attempt by Freescale to create an OS-agnostic sub-driver for
managing the hardware, using shims to interface to the OS-specific APIs. This
work was abandoned, and Freescale's primary work is in the Linux driver (dual
BSD/GPL license). Hence, this was imported directly to sys/contrib, rather than
going through the vendor area. Going forward, FreeBSD-specific changes may be
made to the ncsw code, diverging from the upstream in potentially incompatible
ways. An alternative could be to import the Linux driver itself, using the
linuxKPI layer, as that would maintain parity with the vendor-maintained driver.
However, the Linux driver has not been evaluated for reliability yet, and may
have issues with the import, whereas the ncsw-based driver in this commit was
completed by Semihalf 4 years ago, and is very stable.
Other SoC modules based on DPAA, which could be added in the future:
* Security and Encryption engine (SEC4.x, SEC5.x)
* RAID engine
Additional work to be done:
* Implement polling mode
* Test vlan support
* Add support for the Pattern Matching Engine, which can do regular expression
matching on packets.
This driver has been tested on the P5020 QorIQ SoC. Others listed in the
dtsec(4) manual page are expected to work as the same DPAA engine is included in
all.
Obtained from: Semihalf
Relnotes: Yes
Sponsored by: Alex Perez/Inertial Computing
