r357614 added CTLFLAG_NEEDGIANT to make it easier to find nodes that are
still not MPSAFE (or already are but aren’t properly marked). Use it in
preparation for a general review of all nodes.
This is non-functional change that adds annotations to SYSCTL_NODE and
SYSCTL_PROC nodes using one of the soon-to-be-required flags.
Reviewed by: hselasky, kib
Approved by: kib (mentor)
Differential Revision: https://reviews.freebsd.org/D23632
network device pointer might be NULL. Wait for any pending tasks to
complete before calling axge_stop().
MFC after: 1 week
Sponsored by: Mellanox Technologies
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
axge_setmulti()/axge_setpromisc() with axge_rxfilter().
Multicast filter programming and promiscuous mode requires
access to a common RX configuration register so there is no need to
use separate functions with added complexity. axge_rxfilter() does
not read back AXGE_RCR register since accessing a register in USB
is too slow and we already have all knowledge of required
configuration. Rebuilding RX filter configuration is simpler and
faster than manipulating every bits after reading back the
register.
Note, axge_rxfilter() does not set RCR_IPE(IP header alignment on
32bit boundary) to disable extra padding bytes insertion. The
extra padding wastes ethernet to USB host bandwidth as well as
complicating RX handling logic. Current USB framework requires
copying RX frames to mbufs so there is no need to worry about
alignment. Previously axge_rx_frame() performed wrong bound check
due to the extra padding and it was broken when RX checksum
offloading is disabled. See added comment in axge_rx_frame () for
actual RX packet layout.
In axge_init(), disable WOL. It's meaningless to enable WOL in
normal operation.
In axge_rxeof(), use properly sized mbuf rather than blindly
allocating a mbuf cluster.
Use RX H/W checksum offloading only when administrator requested RX
checksum offloading. Previously it always used RX H/W checksum
offloading result regardless of RX checksum offloading state.
Separate L4 checksum offloading validation from L3 one and properly
set required offloading bits for each layer. This is to fix setting
L4 checksum offloading bits for L3 packets.
There are still lots of RX errors(probably RX FIFO overflows) under
moderate load. Users are strongly recommended to enable ethernet
flow control.
Reviewed by: kevlo (initial version), hselasky
structures. This simplifies mbuf copy operation to USB buffers as
well as improving readability. The controller supports Microsoft
LSOv1(aka TSO) but this change set does not include the support due
to copying overhead to USB buffers and large amount of memory waste.
Remove useless ZLP padding which seems to come from Linux. Required
bits the code tried to set was not copied into USB buffer so it had
no effect. Unlike Linux, FreeBSD USB stack automatically generates
ZLP so no explicit padding is required in driver.[1]
Micro-optimize updating IFCOUNTER_OPACKETS counter by moving it out
of TX loop since updating counter is not cheap operation as it did
long time ago and we already know how many number of packets were
queued after exiting the loop.
While here, fix a checksum offloading bug which will happen when
upper stack computes checksum while H/W checksum offloading is
active. The controller should be notified to not recompute the
checksum in this case.
Reviewed by: kevlo (initial version), hselasky
Pointed out by: hselasky [1]
tables. Some drivers needed some slight re-arrangement of declarations
to accommodate this. Change the USB pnp tables slightly to allow
better compatibility with the system by moving linux driver info from
start of each entry to the end. All other PNP tables in the system
have the per-device flags and such at the end of the elements rather
that at the beginning.
Differential Review: https://reviews.freebsd.org/D3458
- Remove 4 extra bytes from the ethernet payload.
- The maximum RX buffer was incorrectly set. Increase it to 64K for
now, until the exact limit is understood.
- Enable hardware checksumming again.
- Make hardware data structure packed.
MFC after: 3 days
- Don't discard frames if the dropped or error flag is set.
- Don't remove the last 4-bytes of every packet.
- Add extra range check for data position offset when receiving data.
MFC after: 1 day
PR: 191432
adapters. Both devices support Gigabit Ethernet and USB 2.0, and the AX88179
supports USB 3.0. The driver was written by kevlo@ and lwhsu@, with a few
bug fixes from me.
MFC after: 2 months
