When copying big structures, LLVM generates calls to memmove(), because
it may not be able to figure out whether structures overlap. This caused
linker errors to occur. memmove() is now implemented using bcopy().
Ideally it would be the other way around, but that can be solved in the
future. On ARM we don't do add anything, because it already has
memmove().
Discussed on: arch@
Reviewed by: rdivacky
the net80211 layer has complete control over the handling of mgt frames
(in particular, the ac, tx rate, and retry count); this also allows us
to purge the M_LINK0 flag that was attached to mbufs to mark them as
needing encryption for shared key auth
o change ieee80211_send_setup to take a tid parameter so it can be used
to setup QoS frames
For receive:
o explicitly tag rx frames w/ M_AMPDU instead of passing frames through
the reorder processing according to the node having HT and the frame
being QoS data
o relax ieee80211_ampdu_reorder asserts to allow any frame to be passed
in, unsuitable frames are returned to the caller for normal processing;
this permits drivers that cannot inspect the PLCP to mark all data
frames as potential ampdu candidates with only a small penalty
o add M_AMPDU_MPDU to identify frames resubmitted from the reorder q
For transmit:
o tag aggregation candidates with M_AMPDU_MPDU
o fix the QoS ack policy set in ampdu subframes; we only support immediate
BA streams which should be marked for "normal ack" to get implicit block
ack behaviour; interestingly certain vendor parts BA'd frames with the
11e BA ack policy set
o do not assign a sequence # to aggregation candidates; this must be done
when frames are submitted for transmit (NB: this can/will be handled
better when aggregation is pulled up to net80211)
o construct a name for the com lock as done for other locks
o pass the device name to IEEE80211_LOCK_INIT so the mtx name
is constructed as foo_com_lock
o introduce *_LOCK_OBJ macro's to hide the lock contents and
minimize redundant code
Note this includes changes to all drivers and moves some device firmware
loading to use firmware(9) and a separate module (e.g. ral). Also there
no longer are separate wlan_scan* modules; this functionality is now
bundled into the wlan module.
Supported by: Hobnob and Marvell
Reviewed by: many
Obtained from: Atheros (some bits)
device and have had the crypto bits stripped from the 802.11 header
o strip mbuf flags in the rx path before passing up the stack
Reviewed by: thompsa, sephe, avatar
Approved by: re (blanket wireless)
o major overhaul of the way channels are handled: channels are now
fully enumerated and uniquely identify the operating characteristics;
these changes are visible to user applications which require changes
o make scanning support independent of the state machine to enable
background scanning and roaming
o move scanning support into loadable modules based on the operating
mode to enable different policies and reduce the memory footprint
on systems w/ constrained resources
o add background scanning in station mode (no support for adhoc/ibss
mode yet)
o significantly speedup sta mode scanning with a variety of techniques
o add roaming support when background scanning is supported; for now
we use a simple algorithm to trigger a roam: we threshold the rssi
and tx rate, if either drops too low we try to roam to a new ap
o add tx fragmentation support
o add first cut at 802.11n support: this code works with forthcoming
drivers but is incomplete; it's included now to establish a baseline
for other drivers to be developed and for user applications
o adjust max_linkhdr et. al. to reflect 802.11 requirements; this eliminates
prepending mbufs for traffic generated locally
o add support for Atheros protocol extensions; mainly the fast frames
encapsulation (note this can be used with any card that can tx+rx
large frames correctly)
o add sta support for ap's that beacon both WPA1+2 support
o change all data types from bsd-style to posix-style
o propagate noise floor data from drivers to net80211 and on to user apps
o correct various issues in the sta mode state machine related to handling
authentication and association failures
o enable the addition of sta mode power save support for drivers that need
net80211 support (not in this commit)
o remove old WI compatibility ioctls (wicontrol is officially dead)
o change the data structures returned for get sta info and get scan
results so future additions will not break user apps
o fixed tx rate is now maintained internally as an ieee rate and not an
index into the rate set; this needs to be extended to deal with
multi-mode operation
o add extended channel specifications to radiotap to enable 11n sniffing
Drivers:
o ath: add support for bg scanning, tx fragmentation, fast frames,
dynamic turbo (lightly tested), 11n (sniffing only and needs
new hal)
o awi: compile tested only
o ndis: lightly tested
o ipw: lightly tested
o iwi: add support for bg scanning (well tested but may have some
rough edges)
o ral, ural, rum: add suppoort for bg scanning, calibrate rssi data
o wi: lightly tested
This work is based on contributions by Atheros, kmacy, sephe, thompsa,
mlaier, kevlo, and others. Much of the scanning work was supported by
Atheros. The 11n work was supported by Marvell.
station exiting power save mode prepend them to the driver's
send q instead of appending them. This insures the packets
are not misordered wrt any packets already q'd for the station.
This corrects a problem noticed when using a VoIP phone talking
to an ath card in ap mode; the misordered packets caused noise.
Submitted by: "J.R. Oldroyd" <jr@opal.com>
MFC after: 2 weeks
the state machine clocks to INIT, node references are not reclaimed.
Add a new routine ieee80211_drain_ifq that does this and use it
instead of IF_DRAIN.
Submitted by: Sepherosa Ziehau
Obtained from: DragonFly
MFC after: 1 month
Crypto changes:
o change driver/net80211 key_alloc api to return tx+rx key indices; a
driver can leave the rx key index set to IEEE80211_KEYIX_NONE or set
it to be the same as the tx key index (the former disables use of
the key index in building the keyix->node mapping table and is the
default setup for naive drivers by null_key_alloc)
o add cs_max_keyid to crypto state to specify the max h/w key index a
driver will return; this is used to allocate the key index mapping
table and to bounds check table loookups
o while here introduce ieee80211_keyix (finally) for the type of a h/w
key index
o change crypto notifiers for rx failures to pass the rx key index up
as appropriate (michael failure, replay, etc.)
Node table changes:
o optionally allocate a h/w key index to node mapping table for the
station table using the max key index setting supplied by drivers
(note the scan table does not get a map)
o defer node table allocation to lateattach so the driver has a chance
to set the max key id to size the key index map
o while here also defer the aid bitmap allocation
o add new ieee80211_find_rxnode_withkey api to find a sta/node entry
on frame receive with an optional h/w key index to use in checking
mapping table; also updates the map if it does a hash lookup and the
found node has a rx key index set in the unicast key; note this work
is separated from the old ieee80211_find_rxnode call so drivers do
not need to be aware of the new mechanism
o move some node table manipulation under the node table lock to close
a race on node delete
o add ieee80211_node_delucastkey to do the dirty work of deleting
unicast key state for a node (deletes any key and handles key map
references)
Ath driver:
o nuke private sc_keyixmap mechansim in favor of net80211 support
o update key alloc api
These changes close several race conditions for the ath driver operating
in ap mode. Other drivers should see no change. Station mode operation
for ath no longer uses the key index map but performance tests show no
noticeable change and this will be fixed when the scan table is eliminated
with the new scanning support.
Tested by: Michal Mertl, avatar, others
Reviewed by: avatar, others
MFC after: 2 weeks
don't mark the MORE_DATA bit when taking it off the ps queue, there's
no 802.11 header then; we must wait to do this at encap time so
mark the mbuf instead.
Reviewed by: avatar
Approved by: re (scottl)
Obtained from: Atheros
here but it includes completed 802.11g, WPA, 802.11i, 802.1x, WME/WMM,
AP-side power-save, crypto plugin framework, authenticator plugin framework,
and access control plugin frameowrk.
