Repeatedly-tripped-over-by: Vallo Kallaste <vallo@matti.ee>
When VINUMDEBUG is set, free any memory found still
allocated.
Only log errors if DEBUG_EXITFREE is set.
board versions with no BIOS. Separate mailbox interrupts from
IOCB interrupts. Read OUTMAILBOX5 while RISC_INT is active- not
after you clear it (potential race condition). Clear out older broken
BIG_ENDIAN goop. Don't negotiate narrow/async for LVD busses at startup
if already in LVD mode. Note usage of presumptive 1040C revision. For
all the LIP, PDB Changed, Loop UP/DOWN async events, mark fw state
as unknown as well as marking the need to do a getpdb on targets- after
a LIP for certain the f/w has to do PRLI/PLOGI for all targets again
and marking f/w state as unknown gives us a fighting chance to (start
to) hold up for that to complete.
that will SBusify an isp header or the lun/target portions of a request IOCB-
and have these only valid iff __sparc__ (no non-sparc SBus machine that *I*
know about).
free_vinum: Wait for daemon to stop by checking the
vinum_conf.flags & VF_DAEMONOPEN.
vinum_modevent:
When compiled with VINUMDEBUG, check if we have
forgotten to free any memory, and log an error if we
have.
vinumopen: Allow open of an empty subdisk (otherwise we can't
initialize it).
plexes_used and volumes_used. Now these fields are only informative,
and the <object>_allocated count is used for searches, etc. This also
required checking the object state before doing things with the
presumed object.
Problems-reported-by: Kiril Mitev <kiril@ideaglobal.com>
VINUM_<object>CONFIG: return ENXIO rather than EFAULT if an object
doesn't exist.
plexes_used and volumes_used. Now these fields are only informative,
and the <object>_allocated count is used for searches, etc. This also
required checking the object state before doing things with the
presumed object.
Problems-reported-by: Kiril Mitev <kiril@ideaglobal.com>
vinum_scandisk: increment drive use count when we find a good one.
plexes_used and volumes_used. Now these fields are only informative,
and the <object>_allocated count is used for searches, etc. This also
required checking the object state before doing things with the
presumed object.
Problems-reported-by: Kiril Mitev <kiril@ideaglobal.com>
Remove unused (and braindead) functions volume_index, plex_index,
sd_index and drive_index.
Add a flag VF_CREATED for volumes. VF_NEWBORN was being used in two
capacities, and they clashed, my Lord, they clashed.
find_object: restructure the search loop as a result of the change in
variable use.
Decrement object use count in the remove_<object> functions, not in
the free_<object> functions, which are often called with partially
initialized (and uncounted) objects.
plexes_used and volumes_used. Now these fields are only informative,
and the <object>_allocated count is used for searches, etc. This also
required checking the object state before doing things with the
presumed object.
Problems-reported-by: Kiril Mitev <kiril@ideaglobal.com>
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
longjmp. I suspect that the occasional double panic may be the result
of incorrect parameters to longjmp. This happens, of course, like the
entire file, only with -DVINUMDEBUG.
give_sd_to_plex: Don't set Raid-5 subdisk state here.
config_subdisk: handle the name parameter correctly when the subdisk
was referenced in a previous plex definition. The
name parameter must come first.
Handle autosizing relatively correctly. There is
still a danger of losing drive space if problems
occur with an autosized subdisk.
Set state to empty, not up, when complete. This also
solves a nagging problem about enforcing the need to
initialize RAID-5 plexes.
config_plex: handle the name parameter correctly when the plex
was referenced in a previous volume definition. The
name parameter must come first.
Handle initial state better.
update_plex_config:
Calculate the trim factor for RAID-5 plexes correctly.
Set the number of down subdisks correctly when reading
from disk config.
settings you've just sent them and return random values if you follow
the set by a get. This causes problems when you latter run a Tag-enabled
command when you've command tagged mode off.
