and remove non-present symbols that are now reported by kmod_syms.awk.
Reviewed by: emaste
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D32878
VesaLocalBus or EISA. Internally, EISA and ISA are handled the same,
with VL being handled slightly differently. To avoid too much code
churn, retain the EISA name, despite it being used only for ISA
bus. When it is on the ISA bus, weird gymnastics are required with
EISA-space address accesses as well. Remove known models from the ahc
man page. Remove ahc_eisa module.
fallback targets to build the aic generated files. fmake doesn't like
the current construct, and since it doesn't have .MAKE.LEVEL, just
don't provide the fallback targets for fmake. This gives a little
extra compatibility to old systems trying to build new kernels at
almost no cost to the current code.
CWARNFALGS.$file centrally so we don't have to have it in all the
places. Remove a few warning flags that are no longer needed.
Also, always use -Wno-unknown-pragma to (hopefully temporarily) work
around #pragma ident in debug.h in the opensolaris code. Remove some
stale warning suppression that's no longer necessary.
We haven't noticed that it was missing because eisa has been disabled for
a while in -current, but it became apparent when some parallel-build stuff
was MFC'd to 10-stable and this module failed to build there.
options into kern.opts.mk and change all the places where we use
src.opts.mk to pull in the options. Conditionally define SYSDIR and
use SYSDIR/conf/kern.opts.mk instead of a CURDIR path. Replace all
instances of CURDIR/../../etc with STSDIR, but only in the affected
files.
As a special compatibility hack, include bsd.owm.mk at the top of
kern.opts.mk to allow the bare build of sys/modules to work on older
systems. If the defaults ever change between 9.x, 10.x and current for
these options, however, you'll wind up with the host OS' defaults
rather than the -current defaults. This hack will be removed when
we no longer need to support this build scenario.
Reviewed by: jhb
Differential Revision: https://phabric.freebsd.org/D529
drivers and their firmware were under active development, but those days
have passed. The firmware now exists in pre-compiled form, no longer
dependent on it's sources or on aicasm. If you wish to rebuild the
firmware from source, the glue still exists under the 'make firmware'
target in sys/modules/aic7xxx.
This also fixes the problem introduced with r257777 et al with building
kernels the old fashioned way in sys/$arch/compile/$CONFIG when the
ahc/ahd drivers were included.
components instead of with the kernel and/or modules. This ensures that it
gets built with the host compiler, not the compiler in obj/... used to build
the target components (which may be a cross-compiler outputting code for a
different architecture and using header files with types and options set up
for the wrong architecture).
Reviewed by: imp
The ISA probe uses an identify routine to probe all slot locations from
1 to 14 that do not conflict with other allocated resources. This required
making aic7770.c part of the driver core when compiled as a module.
aic7xxx.c:
aic79xx.c:
aic_osm_lib.c:
Use aic_scb_timer_start() consistently to start the watchdog timer.
This removes a few places that verbatum copied the code in
aic_scb_timer_start().
During recovery processing, allow commands to still be queued to
the controller. The only requirement we have is that our recovery
command be queued first - something the code already guaranteed.
The only other change required to make this work is to prevent
timers from being started for these newly queued commands.
Approved by: re
is a compiler tool and needs to be compiled by the host compiler. I've
tested this in i386->sparc cross-build, 4.7->current upgrade, normal
buildkernel target, and normal /sys/i386/compile/GENERIC configurations.
Submitted by: ru
