* Remove ar5416UpdateChainmasks();
* Remove the TX chainmask override code from the ar5416 TX descriptor
setup routines;
* Write a driver method to calculate the current chainmask based on the
operating mode and update the driver state;
* Call the HAL chainmask method before calling ath_hal_reset();
* Use the currently configured chainmask in the TX descriptors rather than
the hardware TX chainmasks.
Tested:
* AR5416, STA/AP mode - legacy and 11n modes
Right now the only way to set the chainmask is to set the hardware
configured chainmask through capabilities. This is fine for forcing
the chainmask to be something other than what the hardware is capable
of (eg to reduce TX/RX to one connected antenna) but it does change what
the HAL hardware chainmask configuration is.
For operational mode changes, it (may?) make sense to separately control
the TX/RX chainmask.
Right now it's done as part of ar5416_reset.c - ar5416UpdateChainMasks()
calculates which TX/RX chainmasks to enable based on the operating mode.
(1 for legacy and whatever is supported for 11n operation.) But doing
this in the HAL is suboptimal - the driver needs to know the currently
configured chainmask in order to correctly enable things for each
TX descriptor. This is currently done by overriding the chainmask
config in the ar5416 TX routines but this has to disappear - the AR9300
HAL support requires the driver to dynamically set the TX chainmask based
on the TX power and TX rate in order to meet mini-PCIe slot power
requirements.
So:
* Introduce a new HAL method to set the operational chainmask variables;
* Introduce null methods for the previous generation chipsets;
* Add new driver state to record the current chainmask separate from
the hardware configured chainmask.
Part #2 of this will involve disabling ar5416UpdateChainMasks() and moving
it into the driver; as well as properly programming the TX chainmask
based on the currently configured HAL chainmask.
Tested:
* AR5416, STA mode - both legacy (11a/11bg) and 11n rates - verified
that AR_SELFGEN_MASK (the chainmask used for self-generated frames like
ACKs and RTSes) is correct, as well as the TX descriptor contents is
correct.
currnet initialization sequence. Set it to simple mode only so that
systems can be updated from stable/7 to newer installations.
At some point, we should figure out why we cannot initialize performant
mode on this board.
PR: kern/153361
Reviewed by: scottl
Obtained from: Yahoo! Inc.
MFC after: 2 weeks
- Remove vestigial null pointer tests after malloc(..., M_WAITOK).
- Remove vestigal qualhack union
- Use strlcpy() instead of the error-prone strncpy() when parsing
EEPROM and copying strings
- Check the MAC address in the EEPROM strings more strictly.
- Expand the macro MXGE_NEXT_STRING() at its only user. Due to a typo,
the macro was very confusing.
- Remove unnecessary buffer limit check. The buffer is double-NUL
terminated per construction.
PR: kern/176369
Submitted by: Christoph Mallon <christoph.mallon gmx.de>
might have been enabled for them- now that we use all 32 bits of handle.
Fast Posting doesn't pass the full 32 bits.
Noticed by: Bugs in NetBSD. Only a NetBSD user might actually still use such old hardware.
MFC after: 1 week
Some hardware like DMA and GPIO controllers might require
more then 8 interrupts per device instance.
Submitted by: Daisuke Aoyama <aoyama at peach.ne.jp>
Discussed with: gber@, raj@
data, introduced by r246713. There are two places where ata_request is
filled in ATA_CAM: ata_cam_begin_transaction() and ata_cam_request_sense().
In the first case DMA should be done for addresses from the CCB. In second
case, DMA should be done to the different address, the address of the sense
buffer inside the CCB structure itself.
- Some mxge nics may store the serial number in the SN2 field of the
EEPROM. These will also have an SN=0 field, so parse the SN2 field,
and give it precedence.
- Skip MXGEFW_CMD_UNALIGNED_TEST on mxge nics which do not require it.
This saves roughly 10ms per port at device attach time.
Sponsored by: Myricom
MFC After: 7 days
- Re-fix build by restoring local removed in r247151, but protected
by #if defined(INET) || defined(INET6) so that the compile
succeeds in the !(INET||INET6) case.
- Protect call to in_pseudo() with an #ifdef INET, to allow
a kernel to link with mxge when INET is not compiled in.
- Also remove an errant (improperly commented) obsolete debugging printf
Thanks to Glebius for pointing out the !(INET||INET6) build issue.
Sponsored by: Myricom
MFC After: 7 days
an incorrectly calculated RTS duration value when transmitting aggregates.
These earlier 802.11n NICs incorrectly used the ACK duration time when
calculating what to put in the RTS of an aggregate frame. Instead it
should have used the block-ack time. The result is that other stations
may not reserve enough time and start transmitting _over_ the top of
the in-progress blockack field. Tsk.
This workaround is to popuate the burst duration field with the delta
between the ACK duration the hardware is using and the required duration
for the block-ack. The result is that the RTS field should now contain
the correct duration for the subsequent block-ack.
This doesn't apply for AR9280 and later NICs.
Obtained from: Qualcomm Atheros
- Add support for IPv6 rx csum offload
- Finally switch mxge from using its own driver lro, to
using tcp_lro
MFC after: 7 days
Sponsored by: Myricom Inc.
DragonFlyBSD, so it certainly doesn't need splsoftvm(). Remove it.
# I doubt this driver will now compile on older FreeBSD versions or DFBSD
# We should consider unifdefing it since that code seems unmaintained.
Specifically - never jack the TX FIFO threshold up to the absolute
maximum; always leave enough space for two DMA transactions to
appear.
This is a paranoia from the Linux ath9k driver. It can't hurt.
Obtained from: Linux ath9k
The default is to limit them to what the hardware is capable of.
Add sysctl twiddles for both the non-RTS and RTS protected aggregate
generation.
Whilst here, add some comments about stuff that I've discovered during
my exploration of the TX aggregate / delimiter setup path from the
reference driver.
- bear with me, there are lots of white space changes, I would not
do them, but I am a mere consumer of this stuff and if these drivers
are to stay in shape they need to be taken.
em driver changes: support for the new i217/i218 interfaces
igb driver changes:
- TX mq start has a quick turnaround to the stack
- Link/media handling improvement
- When link status changes happen the current flow control state
will now be displayed.
- A few white space/style changes.
lem driver changes:
- the shared code uncovered a bogus write to the RLPML register
(which does not exist in this hardware) in the vlan code,this
is removed.
CSUM_TCP too. They are all set explicitly by the kernel usually.
While here, fix an unrelated bug where hardware L4 checksum calculation
was accidentally disabled for some IPv6 packets.
Reported by: alfred@
MFC after: 3 days
This has reduced the number of TX delimiter and data underruns when
doing large UDP transfers (>100mbit).
This stops any HAL_INT_TXURN interrupts from occuring, which is a good
sign!
Obtained from: Qualcomm Atheros
* Delete this debugging print - I used it when debugging the initial
TX descriptor chaining code. It now works, so let's toss it.
It just confuses people if they enable TX descriptor debugging as they
get two slightly different versions of the same descriptor.
* Indenting.
part of ts_status. Thus:
* make sure we decode them from ts_flags, rather than ts_status;
* make sure we decode them regardless of whether there's an error or not.
This correctly exposes descriptor configuration errors, TX delimiter
underruns and TX data underruns.
Make dcons input polling adaptive, reducing poll rate to 1Hz after several
minutes of inactivty to reduce global interrupt rate. Most of users never
used FireWire debugging, so it is not very useful to consume power by it.
unnecessarily by a user thread waiting to run on a specific CPU after
calling sched_bind().
Reviewed by: rstone
Approved by: emaste (co-mentor)
Sponsored by: Sandvine Incorporated
MFC after: 1 week
