This makes our naming scheme more closely match other systems and the
expectations of much third-party software. MIPS builds which are little-endian
should require and exhibit no changes. Big-endian TARGET_ARCHes must be
changed:
From: To:
mipseb mips
mipsn32eb mipsn32
mips64eb mips64
An entry has been added to UPDATING and some foot-shooting protection (complete
with warnings which should become errors in the near future) to the top-level
base system Makefile.
using the o32 ABI. This mostly follows nwhitehorn's lead in implementing
COMPAT_FREEBSD32 on powerpc64.
o) Add a new type to the freebsd32 compat layer, time32_t, which is time_t in the
32-bit ABI being used. Since the MIPS port is relatively-new, even the 32-bit
ABIs use a 64-bit time_t.
o) Because time{spec,val}32 has the same size and layout as time{spec,val} on MIPS
with 32-bit compatibility, then, disable some code which assumes otherwise
wrongly when built for MIPS. A more general macro to check in this case would
seem like a good idea eventually. If someone adds support for using n32
userland with n64 kernels on MIPS, then they will have to add a variety of
flags related to each piece of the ABI that can vary. That's probably the
right time to generalize further.
o) Add MIPS to the list of architectures which use PAD64_REQUIRED in the
freebsd32 compat code. Probably this should be generalized at some point.
Reviewed by: gonzo
Wrong in that it must be guarded (it's configurable)
and bogus in that there's absolutely no rationale for
it not default to a page size like all other archs.
This patch is going to help in cases like mips flavours where you
want a more granular support on MAXCPU.
No MFC is previewed for this patch.
Tested by: pluknet
Approved by: re (kib)
In n32 and n64, add support for physical address above 4GB by having
64 bit page table entries and physical addresses. Major changes are:
- param.h: update PTE sizes, masks and shift values to support 64 bit PTEs.
- param.h: remove DELAY(), mips_btop(same as atop), mips_ptob (same as
ptoa), and reformat.
- param.h: remove casting to unsigned long in trunc_page and round_page
since this will be used on physical addresses.
- _types.h: have 64 bit __vm_paddr_t for n32.
- pte.h: update TLB LO0/1 access macros to support 64 bit PTE
- pte.h: assembly macros for PTE operations.
- proc.h: md_upte is now 64 bit for n32 and n64.
- exception.S and swtch.S: use the new PTE macros for PTE operations.
- cpufunc.h: TLB_LO0/1 registers are 64bit for n32 and n64.
- xlr_machdep.c: Add memory segments above 4GB to phys_avail[] as they are
supported now.
Reviewed by: jmallett (earlier version)
- 32 bit compilation will still use old 2 level page tables
- re-arrange pmap code so that adding another level is easier
- pmap code for 3 level page tables for n64
- update TLB handler to traverse 3 levels in n64
Reviewed by: jmallett
am now able to run 32 cores ok.. but I still will hang
on buildworld with a NFS problem. I suspect I am missing
a patch for the netlogic rge driver.
JC check and see if I am missing anything except your
core-mask changes
Obtained from: JC
address space for an address as aligned by the new pmap_align_tlb()
function, which is for constraints imposed by the TLB. [1]
o) Add a kmem_alloc_nofault_space() function, which acts like
kmem_alloc_nofault() but allows the caller to specify which find-space
option to use. [1]
o) Use kmem_alloc_nofault_space() with VMFS_TLB_ALIGNED_SPACE to allocate the
kernel stack address on MIPS. [1]
o) Make pmap_align_tlb() on MIPS align addresses so that they do not start on
an odd boundary within the TLB, so that they are suitable for insertion as
wired entries and do not have to share a TLB entry with another mapping,
assuming they are appropriately-sized.
o) Eliminate md_realstack now that the kstack will be appropriately-aligned on
MIPS.
o) Increase the number of guard pages to 2 so that we retain the proper
alignment of the kstack address.
Reviewed by: [1] alc
X-MFC-after: Making sure alc has not come up with a better interface.
o) Remove NBPG, PGOFSET and PGSHIFT. Use the standard names.
o) Remove some unused macros and move things from param.h to vmparam.h that
belong in the latter. (Actually, all of the kernel segment values, virtual
addresses, etc., belong in one place, but this is a step in the right
direction.)
ones implemented using assembly.
o) Use TRAPF_USERMODE() consistently rather than USERMODE(). Eliminate
<machine/psl.h> as a result.
o) Use intr_*() rather than *intr(), consistently.
o) Use register_t instead of u_int in some trap code.
o) Merge some more endian-related macros to machine/asm.h from NetBSD.
o) Add PTR_LI macro, which loads an address with the correct sign-extension for
a pointer.
o) Restore interrupts when bailing out due to an excessive IRQ in
nexus_setup_intr().
o) Remove unused functions from psraccess.S.
o) Enter temporary virtual entries for large memory access into the page tables
rather than simply hoping they stay resident in the TLB and we don't need to
do a refill for them.
o) Abstract out large memory mapping setup/teardown using some macros.
o) Do mips_dcache_wbinv_range() when using temporary virtual addresses just
like we do when we can use the direct map.
r201881 | imp | 2010-01-08 20:08:22 -0700 (Fri, 08 Jan 2010) | 3 lines
Rename mips_pcpu_init to mips_pcpu0_init since it applies only to the
BSP. Provide a missing prototype.
r200343 | imp | 2009-12-09 18:44:11 -0700 (Wed, 09 Dec 2009) | 4 lines
Get the sense of this right. We use uintpr_t for bus_addr_t when
we're building everything except octeon && 32-bit. As note before, we
need a clearner way, but at least now the hack is right.
r199760 | imp | 2009-11-24 10:15:22 -0700 (Tue, 24 Nov 2009) | 2 lines
Add in Cavium's CID. Report what the unknown CID is.
r199754 | imp | 2009-11-24 09:32:31 -0700 (Tue, 24 Nov 2009) | 6 lines
Include opt_cputype.h for all .c and .S files referencing TARGET_OCTEON.
Spell ld script name right.
r199599 | imp | 2009-11-20 09:32:26 -0700 (Fri, 20 Nov 2009) | 2 lines
Another kludge for 64-bit bus_addr_t with 32-bit pointers...
r199496 | gonzo | 2009-11-18 15:52:05 -0700 (Wed, 18 Nov 2009) | 5 lines
- Add cpu_init_interrupts function that is supposed to
prepeare stuff required for spinning out interrupts later
- Add API for managing intrcnt/intrnames arrays
- Some minor style(9) fixes
r198958 | rrs | 2009-11-05 11:15:47 -0700 (Thu, 05 Nov 2009) | 2 lines
For XLR adds extern for its bus space routines
r198669 | rrs | 2009-10-30 02:53:11 -0600 (Fri, 30 Oct 2009) | 5 lines
With this commit our friend RMI will now compile. I have
not tested it and the chances of it running yet are about
ZERO.. but it will now compile. The hard part now begins,
making it run ;-)
r198666 | imp | 2009-10-29 18:37:50 -0600 (Thu, 29 Oct 2009) | 2 lines
Add some newer MIPS CO cores.
r198665 | imp | 2009-10-29 18:37:04 -0600 (Thu, 29 Oct 2009) | 4 lines
db_expr_t is really closer to a register_t.
Submitted by: bde@
r198531 | gonzo | 2009-10-27 18:01:20 -0600 (Tue, 27 Oct 2009) | 3 lines
- Remove bunch of declared but not defined cach-related variables
- Add mips_picache_linesize and mips_pdcache_linesize variables
r198354 | neel | 2009-10-21 20:51:31 -0600 (Wed, 21 Oct 2009) | 9 lines
Get rid of the hardcoded constants to define cacheable memory:
SDRAM_ADDR_START, SDRAM_ADDR_END and SDRAM_MEM_SIZE
Instead we now keep a copy of the memory regions enumerated by
platform-specific code and use that to determine whether an address
is cacheable or not.
r198310 | gonzo | 2009-10-20 17:13:08 -0600 (Tue, 20 Oct 2009) | 5 lines
- Commit missing part of "bt" fix: store PC register in pcb_context struct
in cpu_switch and use it in stack_trace function later. pcb_regs contains
state of the process stored by exception handler and therefor is not
valid for sleeping processes.
r198207 | imp | 2009-10-18 08:57:04 -0600 (Sun, 18 Oct 2009) | 2 lines
Undo spamage of last MFC.
r198206 | imp | 2009-10-18 08:56:33 -0600 (Sun, 18 Oct 2009) | 3 lines
_ALIGN has to return u_long, since pointers don't fit into u_int in
64-bit mips.
r198182 | gonzo | 2009-10-16 18:22:07 -0600 (Fri, 16 Oct 2009) | 11 lines
- Use PC/RA/SP values as arguments for stacktrace_subr instead of trapframe.
Context info could be obtained from other sources (see below) no only from
td_pcb field
- Do not show a0..a3 values unless they're obtained from the stack. These
are only confirmed values.
- Fix bt command in DDB. Previous implementation used thread's trapframe
structure as a source info for trace unwinding, but this structure
is filled only when exception occurs. Valid register values for sleeping
processes are in pcb_context array. For curthread use pc/sp/ra for current
frame
r198181 | gonzo | 2009-10-16 16:52:18 -0600 (Fri, 16 Oct 2009) | 2 lines
- Get rid of label_t. It came from NetBSD and was used only in one place
r198154 | rrs | 2009-10-15 15:03:32 -0600 (Thu, 15 Oct 2009) | 10 lines
Does 4 things:
1) Adds future RMI directories
2) Places intr_machdep.c in specfic files.arch pointing to the generic
intr_machdep.c. This allows us to have an architecture dependant
intr_machdep.c (which we will need for RMI) in the machine specific
directory
3) removes intr_machdep.c from files.mips
4) Adds some TARGET_XLR_XLS ifdef's for the machine specific intra_machdep.h. We
may need to look at finding a better place to put this. But first I want to
get this thing compiling.
r198066 | gonzo | 2009-10-13 19:43:53 -0600 (Tue, 13 Oct 2009) | 5 lines
- Move stack tracing function to db_trace.c
- Axe unused extern MipsXXX declarations
- Move all declarations for functions in exceptions.S/swtch.S
from trap.c to respective headers
r197685 | gonzo | 2009-10-01 14:05:36 -0600 (Thu, 01 Oct 2009) | 2 lines
- Sync caches properly when dealing with sf_buf
r196215 | imp | 2009-08-14 10:15:18 -0600 (Fri, 14 Aug 2009) | 6 lines
(u_int) is the wrong type here. Use unsigned long instead, even
though that's only less wrong...
r196199 | imp | 2009-08-13 13:47:13 -0600 (Thu, 13 Aug 2009) | 7 lines
Use unsigned long instead of unsigned for the integer casts here. The
former works for both ILP32 and LP64 programming models, while the
latter fails LP64.
r196089 | gonzo | 2009-08-09 19:49:59 -0600 (Sun, 09 Aug 2009) | 4 lines
- Make i/d cache size field 32-bit to prevent overflow
Submited by: Neelkanth Natu
r195582 | imp | 2009-07-10 13:07:07 -0600 (Fri, 10 Jul 2009) | 2 lines
fix prototype for MipsEmulateBranch.
r195581 | imp | 2009-07-10 13:06:43 -0600 (Fri, 10 Jul 2009) | 2 lines
Better definitions for a few types for n32/n64.
r195580 | imp | 2009-07-10 13:06:15 -0600 (Fri, 10 Jul 2009) | 5 lines
Fixed aligned macros...
r195478 | gonzo | 2009-07-08 16:28:36 -0600 (Wed, 08 Jul 2009) | 5 lines
- Port busdma code from FreeBSD/arm. This is more mature version
that takes into account all limitation to DMA memory (boundaries,
alignment) and implements bounce pages.
- Add BUS_DMASYNC_POSTREAD case to bus_dmamap_sync_buf
r195440 | imp | 2009-07-08 00:01:37 -0600 (Wed, 08 Jul 2009) | 2 lines
Fix atomic_store_64 prototype for 64-bit systems.
r195392 | imp | 2009-07-05 20:27:03 -0600 (Sun, 05 Jul 2009) | 3 lines
The MCOUNT macro isn't going to work in 64-bit mode. Add a note to
this effect.
r195391 | imp | 2009-07-05 20:22:51 -0600 (Sun, 05 Jul 2009) | 3 lines
Provide a macro for PTR_ADDU as well. We may need to implement this
differently for N32... Use PTR_ADDU in DO_AST macro.
r195390 | imp | 2009-07-05 20:22:06 -0600 (Sun, 05 Jul 2009) | 4 lines
Change the addu here to daddu.
addu paranoina prodded by: jmallet@
r195382 | imp | 2009-07-05 15:16:26 -0600 (Sun, 05 Jul 2009) | 5 lines
addu and subu are special. We need to use daddu and dsubu here to get
proper behavior.
Submitted by: jmallet@
r195370 | imp | 2009-07-05 09:20:16 -0600 (Sun, 05 Jul 2009) | 6 lines
The SB1 has cohernet memory, so add it.
Also, Maxmem is better as a long.
Submitted by: Neelkanth Natu
r195369 | imp | 2009-07-05 09:19:28 -0600 (Sun, 05 Jul 2009) | 4 lines
The SB1 needs a special value for the cache field of the pte.
Submitted by: Neelkanth Natu
r195368 | imp | 2009-07-05 09:18:06 -0600 (Sun, 05 Jul 2009) | 2 lines
compute the areas to save registers in for 64-bit access correctly.
r195367 | imp | 2009-07-05 09:17:11 -0600 (Sun, 05 Jul 2009) | 3 lines
First cut at 64-bit types. not 100% sure these are all correct for
N32 ABI.
r195366 | imp | 2009-07-05 09:16:27 -0600 (Sun, 05 Jul 2009) | 3 lines
Trim unreferenced goo. SDRAM likely should be next, but it is still
referenced.
r195365 | imp | 2009-07-05 09:13:24 -0600 (Sun, 05 Jul 2009) | 9 lines
First cut at atomics for 64-bit machines and SMP machines.
# Note: Cavium provided a port that has atomics similar to these, but
# that does a syncw; sync; atomic; sync; syncw where we just do the classic
# mips 'atomic' operation (eg ll; frob; sc). It is unclear to me why
# the extra is needed. Since my initial target is one core, I'll defer
# investigation until I bring up multiple cores. syncw is an octeon specific
# instruction.
r195359 | imp | 2009-07-05 02:14:00 -0600 (Sun, 05 Jul 2009) | 4 lines
Bring in cdefs.h from NetBSD to define ABI goo.
Obtained from: NetBSD
r195358 | imp | 2009-07-05 02:13:19 -0600 (Sun, 05 Jul 2009) | 4 lines
Pull in machine/cdefs.h for the ABI definitions. Provide a PTR_LA,
ala sgi, and use it in preference to a bare 'la' so that it gets
translated to a 'dla' for the 64-bit pointer ABIs.
r195357 | imp | 2009-07-05 01:01:34 -0600 (Sun, 05 Jul 2009) | 2 lines
Use uintptr_t rather than unsigned here for 64-bit correctness.
r195356 | imp | 2009-07-05 01:00:51 -0600 (Sun, 05 Jul 2009) | 6 lines
Define __ELF_WORD_SIZE appropriately for n64. Note for N32 I believe
this is correct. While registers are 64-bit, n32 is a 32-bit ABI and
lives in a 32-bit world (with explicit 64-bit registers, however).
Change an 8, which was 4 + 4 or sizeof(int) + SZREG to be a simple '4
+ SZREG' to reflect the actual offset of the structure in question.
r195355 | imp | 2009-07-05 00:56:51 -0600 (Sun, 05 Jul 2009) | 7 lines
(1) Use uintptr_t in preference to unsigned. The latter isn't right for
64-bit case, while the former is.
(2) include a SB1 specific coherency mapping
Submitted by: Neelkanth Nath (2)
r195352 | imp | 2009-07-05 00:44:37 -0600 (Sun, 05 Jul 2009) | 3 lines
db_expr_t should be a intptr_t, not an int. These expressions can be
addresses or numbers, and that's a intptr_t if I ever saw one.
r195351 | imp | 2009-07-05 00:43:01 -0600 (Sun, 05 Jul 2009) | 4 lines
Define COP0_SYNC for SB1 CPU.
Submitted by: Neelkanth Natu
r195350 | imp | 2009-07-05 00:39:37 -0600 (Sun, 05 Jul 2009) | 7 lines
Switch to ABI agnostic ta0-ta3. Provide defs for this in the right
places. Provide n32/n64 register name defintions. This should have
no effect for the O32 builds that everybody else uses, but should help
make N64 builds possible (lots of other changes are needed for that).
Obtained from: NetBSD (for the regdef.h changes)
r195128 | gonzo | 2009-06-27 17:27:41 -0600 (Sat, 27 Jun 2009) | 4 lines
- Add support for handling TLS area address in kernel space.
From the userland point of view get/set operations are
performed using sysarch(2) call.
r195076 | gonzo | 2009-06-26 13:54:06 -0600 (Fri, 26 Jun 2009) | 2 lines
- Add guards to ensure that these files are included only once
r194469 | gonzo | 2009-06-18 22:43:49 -0600 (Thu, 18 Jun 2009) | 16 lines
- Mark temp variable as "earlyclobber" in assembler inline in
atomic_fetchadd_32. Without it gcc would use it as input
register for v and sometimes generate following code for
function call like atomic_fetchadd_32(&(fp)->f_count, -1):
801238b4: 2402ffff li v0,-1
801238b8: c2230018 ll v1,24(s1)
801238bc: 00431021 addu v0,v0,v1
801238c0: e2220018 sc v0,24(s1)
801238c4: 1040fffc beqz v0,801238b8 <dupfdopen+0x2e8>
801238c8: 00000000 nop
Which is definitly wrong because if sc fails v0 is set to 0
and previous value of -1 is overriden hence whole operation
turns to bogus
r194164 | imp | 2009-06-14 00:14:25 -0600 (Sun, 14 Jun 2009) | 3 lines
bye bye. This is no longer referenced, but much code from it will
resurface for a bus-space implementation.
r194160 | imp | 2009-06-14 00:10:36 -0600 (Sun, 14 Jun 2009) | 3 lines
Cavium-specific goo is no longer necessary here. Of course, I now
have to write a bus space for cavium, but that shouldn't be too hard.
r194157 | imp | 2009-06-14 00:01:46 -0600 (Sun, 14 Jun 2009) | 2 lines
Move this to a more approrpiate plae.
r194156 | imp | 2009-06-13 23:29:13 -0600 (Sat, 13 Jun 2009) | 2 lines
Bring this in from the cavium port.
r193487 | gonzo | 2009-06-05 02:37:11 -0600 (Fri, 05 Jun 2009) | 2 lines
- Use restoreintr instead of enableint while accessing pcpu in DO_AST
r192864 | gonzo | 2009-05-26 16:40:12 -0600 (Tue, 26 May 2009) | 4 lines
- Replace CPU_NOFPU and SOFTFLOAT options with CPU_FPU. By default
we assume that there is no FPU, because majority of SoC does
not have it.
r192817 | gonzo | 2009-05-26 10:35:05 -0600 (Tue, 26 May 2009) | 2 lines
- Add type cast for atomic_cmpset_acq_ptr arguments
r192792 | gonzo | 2009-05-26 00:01:17 -0600 (Tue, 26 May 2009) | 2 lines
- Remove now unused NetBSDism intr.h
r192177 | gonzo | 2009-05-15 20:39:13 -0600 (Fri, 15 May 2009) | 4 lines
- Add MIPS_IS_KSEG0_ADDR, MIPS_IS_KSEG1_ADDR and MIPS_IS_VALID_PTR
macroses thet check if address belongs to KSEG0, KSEG1 or both
of them respectively.
r191589 | gonzo | 2009-04-27 13:18:55 -0600 (Mon, 27 Apr 2009) | 3 lines
- Cast argument to proper type in order to avoid warnings like
"shift value is too large for given type"
r191577 | gonzo | 2009-04-27 12:29:59 -0600 (Mon, 27 Apr 2009) | 4 lines
- Use naming convention the same as MIPS spec does: eliminate _sel1 sufix
and just use selector number. e.g. mips_rd_config_sel1 -> mips_rd_config1
- Add WatchHi/WatchLo accessors for selctors 1..3 (for debug purposes)
r191451 | gonzo | 2009-04-23 22:17:21 -0600 (Thu, 23 Apr 2009) | 4 lines
- Define accessor functions for CP0 Config(16) register selects 1, 2, 3.
Content of these registers is defined in MIPS spec and can be used
for obtaining info about CPU capabilities.
r191282 | gonzo | 2009-04-19 16:02:14 -0600 (Sun, 19 Apr 2009) | 3 lines
- Make mips_bus_space_generic be of type bus_space_tag_t instead of
struct bus_space and update all relevant places.
r191084 | gonzo | 2009-04-14 20:28:26 -0600 (Tue, 14 Apr 2009) | 6 lines
Use FreeBSD/arm approach for handling bus space access: space tag is a pointer
to bus_space structure that defines access methods and hence every bus can
define own accessors. Default space is mips_bus_space_generic. It's a simple
interface to physical memory, values are read with regard to host system
byte order.
o add to platforms where it was missing (arm, i386, powerpc, sparc64, sun4v)
o define as "1" on amd64 and i386 where there is no restriction
o make the type returned consistent with ALIGN
o remove _ALIGNED_POINTER
o make associated comments consistent
Reviewed by: bde, imp, marcel
Approved by: re (kensmith)
a fair number of static data structures, making this an unlikely
option to try to change without also changing source code. [1]
Change default cache line size on ia64, sparc64, and sun4v to 128
bytes, as this was what rtld-elf was already using on those
platforms. [2]
Suggested by: bde [1], jhb [2]
MFC after: 2 weeks
CACHE_LINE_SIZE constant. These constants are intended to
over-estimate the cache line size, and be used at compile-time
when a run-time tuning alternative isn't appropriate or
available.
Defaults for all architectures are 64 bytes, except powerpc
where it is 128 bytes (used on G5 systems).
MFC after: 2 weeks
Discussed on: arch@
sys/param.h and move the MI numbers out of here. Also move the MI
defines. Also remove a couple defines not in use (not sure if it is
age, or OpenBSD origins for thse). Note the current values that are
overrides that appear to be odd in some way.
More cleanup could be done here: NBPG appears to be spelled PAGE_SIZE
these days. There's new ways to spell PGOFSET and PGSHIFT too, I
think. These constants duplicate the MI constants and are sprinkled
into the mips code only. Further investigation is needed.
mips32r2 and mips64r2 (and close relatives) processors. There
presently is support for ADMtek ADM5120, A mips 4Kc in a malta board,
the RB533 routerboard (based on IDT RC32434) and some preliminary
support for sibtye/broadcom designs. Other hardware support will be
forthcomcing.
This port boots multiuser under gxemul emulating the malta board and
also bootstraps on the hardware whose support is forthcoming...
Oleksandr Tymoshenko, Wojciech Koszek, Warner Losh, Olivier Houchard,
Randall Stewert and others that have contributed to the mips2 and/or
mips2-jnpr perforce branches. Juniper contirbuted a generic mips port
late in the life cycle of the misp2 branch. Warner Losh merged the
mips2 and Juniper code bases, and others list above have worked for
the past several months to get to multiuser.
In addition, the mips2 work owe a debt to the trail blazing efforts of
the original mips branch in perforce done by Juli Mallett.
