sc_rixmap is an inverse map
NB: could eliminate the check for an invalid rate by filling in 0 for
invalid entries but the rate control modules use it to identify
bogus rates so leave it for now
o call ieee80211_encap in ieee80211_start so frames passed down to drivers
are already encapsulated
o remove ieee80211_encap calls in drivers
o fixup wi so it recreates the 802.3 head it requires from the 802.11
header contents
o move fast-frame aggregation from ath to net80211 (conditional on
IEEE80211_SUPPORT_SUPERG):
- aggregation is now done in ieee80211_start; it is enabled when the
packets/sec exceeds ieee80211_ffppsmin (net.wlan.ffppsmin) and frames
are held on a staging queue according to ieee80211_ffagemax
(net.wlan.ffagemax) to wait for a frame to combine with
- drivers must call back to age/flush the staging queue (ath does this
on tx done, at swba, and on rx according to the state of the tx queues
and/or the contents of the staging queue)
- remove fast-frame-related data structures from ath
- add ieee80211_ff_node_init and ieee80211_ff_node_cleanup to handle
per-node fast-frames state (we reuse 11n tx ampdu state)
o change ieee80211_encap calling convention to include an explicit vap
so frames coming through a WDS vap are recognized w/o setting M_WDS
With these changes any device able to tx/rx 3Kbyte+ frames can use fast-frames.
Reviewed by: thompsa, rpaulo, avatar, imp, sephe
o remove ic_myaddr from ieee80211com
o change ieee80211_ifattach to take the mac address of the physical device
and use that to setup the lladdr.
o replace all references to ic_myaddr in drivers by IF_LLADDR
o related cleanups (e.g. kill dead code)
PR: kern/133178
Reviewed by: thompsa, rpaulo
o break out version-related code to simplify rev'ing the protocol
o add parameter validation macros so checks that appear multiple places
are consistent (and easy to change)
o add protocol version check when looking for a scan candidate
o improve scan debug output format
o rewrite beacon update handling to calculate a bitmask of changed values
and pass that down through the driver callback so drivers can optimize work
o do slot bounds check before use when parsing received beacons
o add 9280 attach that sets up ini, cal, etc.
o new rf backend for 9280 and later parts
o split ini setup and spur mitigation support out to methods
and provide 9280-specific support
o minor fixups to shared code to handle 9280-specific work
Obtained from: Atheros (ini values and some code)
o add ah_configPCIE and ah_disablePCIE for drivers to configure PCIE
power save operation (modeled after ath9k, may need changes)
o add private state flag to indicate if device is PCIE (replaces private
hack in 5212 code)
o add serdes programming ini bits for 5416 and later parts and setup
for each part (5416 and 9160 logic hand-crafted from existing routines);
5212 remains open-coded but is now hooked in via ah_configPCIE
o add PCIE workaround gunk
o add ar5416AttachPCIE for iodomatic code used by 5416 and later parts
o add output mux support
o gpio pin count is chip-dependent
o 9280 and 9285 do input handling different
o hookup gpio interrupts
o no need to save/restore soft led state around reset
o mark phy type to indicate 1/2 or 1/4-rate operation
o use phy type instead of channel attributes to identify 1/2 and 1/4-rate
operation
o general cleanup of code including move phy constants to ah_internal.h
Eventually this code should go away and we should use the net0211 equivalents.
guaranteed to initialize its two last arguments. Therefore, there is a
warning in the subsequent caller ar5416FillVpdTable(), which doesn't
initialize those arguments.
Change getLowerUpperIndex() to assign values to indexL and indexR even
in the case of assertion failure.
Submitted by: Pavel Roskin <proski@gnu.org>
